Hardware specification
----------------------
SoC: MediaTek MT7986A 4x A53
Flash: 128MB SPI-NAND, 8GB eMMC
RAM: 2GB DDR4
Ethernet: 2x 2.5GbE (Airoha EN8811H)
WiFi: MediaTek MT7976C 2x2 2.4G + 3x3 5G
Interfaces:
* M.2 Key-M: PCIe 2.0 x2 for NVMe SSD
* M.2 Key-B: USB 3.0 with SIM slot
* front USB 2.0 port
LED: Power, Status, WLAN2G, WLAN5G, LTE, SSD
Button: Reset, internal boot switch
Fan: PWM-controlled 5V fan
Power: 12V Type-C PD
Installation instructions for eMMC
----------------------------------
0. Set boot switch to boot from SPI-NAND (assuming stock rom or immortalwrt
running there).
1. Write GPT partition table to eMMC
Move openwrt-mediatek-filogic-bananapi_bpi-r3-mini-emmc-gpt.bin to
the device /tmp using scp and write it to /dev/mmcblk0:
dd if=/tmp/openwrt-*-r3-mini-emmc-gpt.bin of=/dev/mmcblk0
2. Reboot (to reload partition table)
3. Write bootloader and OpenWrt images
Move files to the device /tmp using scp:
- openwrt-*-bananapi_bpi-r3-mini-emmc-preloader.bin
- openwrt-*-bananapi_bpi-r3-mini-emmc-bl31-uboot.fip
- openwrt-*-bananapi_bpi-r3-mini-initramfs-recovery.itb
- openwrt-*-bananapi_bpi-r3-mini-squashfs-sysupgrade.itb
Write them to the appropriate partitions:
echo 0 > /sys/block/mmcblk0boot0/force_ro
dd if=/tmp/openwrt-*-bananapi_bpi-r3-mini-emmc-preloader.bin of=/dev/mmcblk0boot0
dd if=/tmp/openwrt-*-bananapi_bpi-r3-mini-emmc-bl31-uboot.fip of=/dev/mmcblk0p3
dd if=/tmp/openwrt-*-bananapi_bpi-r3-mini-initramfs-recovery.itb of=/dev/mmcblk0p4
dd if=/tmp/openwrt-*-bananapi_bpi-r3-mini-squashfs-sysupgrade.itb of=/dev/mmcblk0p5
sync
4. Remove the device from power, set boot switch to eMMC and boot into
OpenWrt. The device will come up with IP 192.168.1.1 and assume the
Ethernet port closer to the USB-C power connector as LAN port.
5. If you like to have Ethernet support inside U-Boot (eg. to boot via
TFTP) you also need to write the PHY firmware to /dev/mmcblk0boot1:
echo 0 > /sys/block/mmcblk0boot1/force_ro
dd if=/lib/firmware/airoha/EthMD32.dm.bin of=/dev/mmcblk0boot1
dd if=/lib/firmware/airoha/EthMD32.DSP.bin bs=16384 seek=1 of=/dev/mmcblk0boot1
Installation instructions for NAND
----------------------------------
0. Set boot switch to boot from eMMC (assuming OpenWrt is installed there
by instructions above. Using stock rom or immortalwrt does NOT work!)
1. Write things to NAND
Move files to the device /tmp using scp:
- openwrt-*-bananapi_bpi-r3-mini-snand-preloader.bin
- openwrt-*-bananapi_bpi-r3-mini-snand-bl31-uboot.fip
- openwrt-*-bananapi_bpi-r3-mini-initramfs-recovery.itb
- openwrt-*-bananapi_bpi-r3-mini-squashfs-sysupgrade.itb
Write them to the appropriate locations:
mtd write /tmp/openwrt-*-bananapi_bpi-r3-mini-snand-preloader.bin /dev/mtd0
ubidetach -m 1
ubiformat /dev/mtd1
ubiattach -m 1
volsize=$(wc -c < /tmp/openwrt-*-bananapi_bpi-r3-mini-snand-bl31-uboot.fip)
ubimkvol /dev/ubi0 -N fip -n 0 -s $volsize -t static
ubiupdatevol /dev/ubi0_0 /tmp/openwrt-*-bananapi_bpi-r3-mini-snand-bl31-uboot.fip
cd /lib/firmware/airoha
cat EthMD32.dm.bin EthMD32.DSP.bin > /tmp/en8811h-fw.bin
ubimkvol /dev/ubi0 -N en8811h-firmware -n 1 -s 147456 -t static
ubiupdatevol /dev/ubi0_1 /tmp/en8811h-fw.bin
ubimkvol /dev/ubi0 -n 2 -N ubootenv -s 126976
ubimkvol /dev/ubi0 -n 3 -N ubootenv2 -s 126976
volsize=$(wc -c < /tmp/openwrt-*-bananapi_bpi-r3-mini-initramfs-recovery.itb)
ubimkvol /dev/ubi0 -n 4 -N recovery -s $volsize
ubiupdatevol /dev/ubi0_4 /tmp/openwrt-*-bananapi_bpi-r3-mini-initramfs-recovery.itb
volsize=$(wc -c < /tmp/openwrt-*-bananapi_bpi-r3-mini-squashfs-sysupgrade.itb)
ubimkvol /dev/ubi0 -n 4 -N recovery -s $volsize
ubiupdatevol /dev/ubi0_4 /tmp/openwrt-*-bananapi_bpi-r3-mini-squashfs-sysupgrade.itb
3. Remove the device from power, set boot switch to NAND, power up and
boot into OpenWrt.
Partially based on immortalwrt support for the R3 mini, big thanks for
doing the ground work!
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add PHY driver for Airoha EN8811H PHY and package it as kernel module.
The PHY needs to load firmware from rootfs, so there is no point in
having the driver built-into the kernel.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Firmware for the built-in 2.5G Ethernet PHY of the MediaTek MT7988 SoC
is now part of linux-firmware, so we can package it.
Only a single file is needed with recent driver.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Move fip and factory into UBI static volumes.
Use fitblk instead of partition parser.
!! RUN INSTALLER FIRST !!
Existing users of previous OpenWrt releases or snapshot builds will
have to **re-run the updated installer** before upgrading to firmware
after this commit.
DO NOT flash or run even just the initramfs image unless you have
run the updated installer which moves the content of the 'factory'
partition into a UBI volume.
tl;dr: DON'T USE YET!
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Modernize bootloader and flash memory layout of the BPi-R64 similar to
how it has also been done for the BPi-R3.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* Switch to all-UBI layout on SPI-NAND
* use fitblk driver instead of uImage.FIT partition parser
* adapt sysupgrade
* bump COMPAT_VERSION
Remove BROKEN mark now that all needed changes are done.
Boards running images generated before this commit will require
full reflash of the bootloader, re-install from SD card is the
easiest way to achieve that.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add environment settings for the BananaPi BPI-R4 router board which
can boot from (and store its bootloader environment on) micro SD card,
SPI-NAND and eMMC.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Hardware
--------
SOC: MediaTek MT7988A (4x Cortex-A73)
RAM: 4 GiB DDR4
Flash: 128 MiB Winbond SPI-NAND
MMC: 8 GiB eMMC *or* microSD (cannot be used both)
ETH: 4x 1GE (1x WAN, 3x LAN)
2x SFP+ (10G, 5G, 2.5G, 1G)
USB: on-board USB 3.2 4-port hub
1x USB 3.2 port (type A connector)
1x M.2 for 4G/5G modem
2x mPCIe for additional modems
WiFi: optional MediaTek MT7996 Wi-Fi 7 module
(using 2x PCIe gen3 x2 on the mPCIe slots and 12V power)
Installation
------------
1. Decompress and write the sdcard image to a micro SD card and use that
to boot the R4 (both dip switches in upper position).
2. Use the bootloader menu accessible via the serial console to install
to SPI-NAND.
3. Switch to boot from SPI-NAND and install to eMMC.
Known issues
------------
- The RST button is hard-wired to the SoC reset and can't be read
from software. This can be changed by modifying the board (ie.
moving a 0-ohm resistor). However, in order to maintain compatibility
with the board as it comes from factory the button isn't used by
OpenWrt and the WPS button is used as factory/reset button instead.
- various small things still need to be fixed in DT
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Import patch from MediaTek SDK which allows using the third
PCIe host controller of the MT7988 SoC.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add UART pinctrl group for using only pins 80 and 81 for uart1.
This is needed on the BPi-R4 as RTS/CTS signals are used for other
on-board functions.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Replace previous patch adding paths and SerDes modes with patch series
pending upstream adding dedicated drivers for XFI T-PHY and USXGMII PCS,
extends LynxI PCS to be a standalone platform driver and as a consequence
makes much less changes to the actual Ethernet driver mtk_eth_soc.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Backport almost 50 commits from upstream Linux to improve thermal
drivers for MediaTek SoCs and add new LVTS driver for MT7988.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Let's pick a bunch of useful phylink changes which allow us to keep
drivers in sync with mainline Linux.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add 'fitblk' driver to replace the rejected/deprecated uImage.FIT
partition parser.
To use the new driver, add phandle /chosen/rootdisk and point it to
the MTD partition, UBI volume or block device holding the uImage.FIT.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Similar to supporting nvmem-layouts on MTD devices, also allow referencing
UBI and MMC devices in DT.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
In order to allow gradually migrating the boards currently using the
uImage.FIT partition (deprecated/rejected) parser to the new fitblk
driver, skip the partition parser code in case the new fitblk driver
(which serves the same purpose) is used.
As an indicator for the use of the new fitblk driver, check if the
/chosen/rootdisk property is present in the Device Tree.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The partition parser approach has been rejected upstream, it will be
replaced by a small block driver which is the solution suggestion by
upstream maintainers.
As the partition parser has only been used by the mediatek target, as
a first step, move it there.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Backport two commits from Linux 6.3 wiring up device node parents of
ubi devices (pointing to their MTD parent) as well as ubiblock devices
(poiting to their parent UBI volume).
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Convert qca807x PHY to new implementation like for other devices.
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Reviewed-by: Robert Marko <robimarko@gmail.com>
Now that Malibu (QCA807x) PHY is using the upstream driver, we dont need
support to define address of the first PHY in package, so remove the
malibu_first_phy_addr DTS property.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Now that QCA807x interface mode check was upstreamed, use the upstreamed
version and mark it as such.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Use order described as preferred in DTS Coding Style. Mostly just move
"compatible", "reg", "ranges" and "status" properties.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
PoE devices in the realtek target have the possibility to add PSE info
to the board description via 02_network. Make this available for all
targets, by moving the uci_set_poe() function to the globally available
uci-default.sh script.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
uci_set_poe() now performs two duties: filtering the list of device
ports to exclude non-PoE ports, and generating the PoE related device
config.
Extract the port filtering to an external function, which is made a bit
more readable by the use of 'sort -V [-r] | uniq -u' to filter duplicate
entries out of a (reverse) version sorted list.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
The ZyXEL XGS1250-12 has a chassis fan. The fan is positioned perfectly to
provide additional cooling to the Aquantia NBase-T phys. Testing has shown
that the phys can reach temperatures upwards of 72 degrees Celsius quite
easily at about 20 degrees Celsius ambient.
Support the chassis fan to give the phys a bit of extra cooling.
Signed-off-by: Tobias Schramm <tobias@t-sys.eu>
Currently, we are checking whether the PHY package mode matches the
individual PHY interface modes at PHY package probe time, but at that time
we only know the PHY package mode and not the individual PHY interface
modes as of_get_phy_mode() that populates it will only get called once the
netdev to which PHY-s are attached to is being probed and thus this check
will always fail and return -EINVAL.
So, lets move this check to .config_init_once as at that point individual
PHY interface modes should be populated.
Fixes: 16364e4100 ("generic: 6.1: backport QCA807x PHY patches")
Signed-off-by: Robert Marko <robimarko@gmail.com>
This Qualcomm Gigabit phy driver was mistakenly added because
MT76x8 does not support external phy, and it only supports max
100M full duplex speed.
Fixes: cadf517107 ("ralink: add support for mt7628")
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Xiaomi AX9000 apply a special PHY LEDs configuration where the unique
green LED for each qca807x PHY port is turned on also on 1000Mbps link.
Apply this special configuration to reflect original implementation.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Xiaomi AX3600 apply a special PHY LEDs configuration where the unique
green LED for each qca807x PHY port is turned on also on 1000Mbps link.
Apply this special configuration to reflect original implementation.
Also enable CONFIG_PHYLIB_LEDS to actually expose the PHY LEDs if
defined in DT.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Convert every qca807x PHY definition in DT to new PHY package
implementation to correctly support applying fixup for the correct PHY
mode.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Port 0-4 have the mode set to SGMII instead of PSGMII. Now that we use
the upstream qca807x driver, this conflicts with the qca SSDK driver
that expects the mode to be PSGMII as for not integrated driver, it does
refer to the real PHY mode.
Update the entry for port 0-4 to PSGMII to solve warning from qca SSDK
in ipq8074-ess.dtsi.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
IPQ807x have integrated qca8074 PHY supported by the upstream qca807x driver.
Enable it to use it instead of the downstream qca SSDK variant.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Adapt patches to new Upstream QCA807x PHY driver.
Rework the PHY patch to new PHY Package nodes.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Backport QCA807x PHY patches merged upstream that introduce the new
concept of PHY package.
Also add in generic config the new Kconfig CONFIG_QCA807X_PHY.
All affected patch automatically refreshed with make
target/linux/refresh.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Backport Aquantia PHY endianess patch. While the current implementation
works ok for Little-Endian targets, backport patch to prevent any kind
of malfunction if in the future we will have Big-Endian target with
Aquantia PHYs.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Commit d737ae99cb ("qualcommax: Fix Buffalo WXR-5950AX12 Ethernet
DTS") reverted the switch bmp to the original OEM definition and
added the malibu_first_phy_addr property.
Problem is that OEM bmp definition is wrong and actually doesn't make sense,
probably caused by copy-paste of the QCOM reference DTS without actually
setting real values. What actually fixed the regression was adding the
malibu_first_phy_addr as without it the MALIBU PHY was actually not
correctly configured and the Aquantia PHY were actually configured as
MALIBU PHY.
Fix all these wrong PHY definition.
The BPM is reverted and the following fixes are applied:
- Drop ESS_PORT1 as it's not actually attached in HW.
- Move ESS_PORT5 AGAIN from lan to wan. This refer to the first Aquantia
PHY that is labelled "wan"
- Move ESS_PORT6 AGAIN from wan to lan. This refer to the second
Aquantia PHY that is labelled "lan1".
Also PHY tag in MDIO node are renumbered to start from 0 following the
tagging standard used also in other dts and the not attached one (reg
0x18 and reg 0x1c) are correctly dropped.
Definition for port@1 in phyinfo is dropped as it doesn't exist.
dp nodes are updated to reference the new PHY tag numbering.
Fixes: d737ae99cb ("qualcommax: Fix Buffalo WXR-5950AX12 Ethernet DTS")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The NWA50AX Pro only has a eth0 interface for its only ethernet port.
Use this port for preinit.
Fixes non-working network in failsafe mode.
Signed-off-by: David Bauer <mail@david-bauer.net>
u64_stats_init() has been unable to handle NULL pointer since
6.1 kernel. This patch fixes kernel oops on mt76x8 and rt305x
sub-target.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
In the 5.15 kernel, we use the staging driver version instead of the
downstream file.
Fixes: 88d982e3bd ("ramips: 6.1: mt7621-dma: add hsdma driver to files")
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Fixes errors in the form of:
make[9]: Entering directory '/home/nick/openwrt/build_dir/target-mipsel_24kc_musl/linux-ramips_mt7620/linux-6.1.77'
CC drivers/net/ethernet/ralink/mtk_eth_soc.o
drivers/net/ethernet/ralink/mtk_eth_soc.c: In function 'fe_init':
drivers/net/ethernet/ralink/mtk_eth_soc.c:1368:51: warning: passing argument 2 of 'of_get_mac_address' discards 'const' qualifier from pointer target type [-Wdiscarded-qualifiers]
1368 | of_get_mac_address(priv->dev->of_node, dev->dev_addr);
| ~~~^~~~~~~~~~
In file included from drivers/net/ethernet/ralink/mtk_eth_soc.c:26:
./include/linux/of_net.h:16:59: note: expected 'u8 *' {aka 'unsigned char *'} but argument is of type 'const unsigned char *'
16 | extern int of_get_mac_address(struct device_node *np, u8 *mac);
| ~~~~^~~
drivers/net/ethernet/ralink/mtk_eth_soc.c: In function 'fe_probe':
drivers/net/ethernet/ralink/mtk_eth_soc.c:1641:9: error: too many arguments to function 'netif_napi_add'
1641 | netif_napi_add(netdev, &priv->rx_napi, fe_poll, napi_weight);
| ^~~~~~~~~~~~~~
In file included from ./include/linux/etherdevice.h:21,
from drivers/net/ethernet/ralink/mtk_eth_soc.c:21:
./include/linux/netdevice.h:2611:1: note: declared here
2611 | netif_napi_add(struct net_device *dev, struct napi_struct *napi,
| ^~~~~~~~~~~~~~
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
[split commit and rewrite commit message]
Signed-off-by: Nick Hainke <vincent@systemli.org>
Upstream commit f48dc6b96649 ("spi: Retire legacy GPIO handling") [0]
removed support using GPIOs as chip select. Fix it by replacing cs_gpio
with cs_gpiod.
[0] - f48dc6b966
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
[split commit and rewrite commit message]
Signed-off-by: Nick Hainke <vincent@systemli.org>
Change fe_hw_set_macaddr and the set_mac parameter to const to fix
errors in the form of:
drivers/net/ethernet/ralink/mtk_eth_soc.c: In function 'fe_set_mac_address':
drivers/net/ethernet/ralink/mtk_eth_soc.c:174:53: error: passing argument 2 of 'priv->soc->set_mac' discards 'const' qualifier from pointer target type [-Werror=discarded-qualifiers]
174 | priv->soc->set_mac(priv, dev->dev_addr);
| ~~~^~~~~~~~~~
drivers/net/ethernet/ralink/mtk_eth_soc.c:174:53: note: expected 'unsigned char *' but argument is of type 'const unsigned char *'
drivers/net/ethernet/ralink/mtk_eth_soc.c: In function 'fe_hw_init':
drivers/net/ethernet/ralink/mtk_eth_soc.c:1220:45: error: passing argument 2 of 'priv->soc->set_mac' discards 'const' qualifier from pointer target type [-Werror=discarded-qualifiers]
1220 | priv->soc->set_mac(priv, dev->dev_addr);
| ~~~^~~~~~~~~~
drivers/net/ethernet/ralink/mtk_eth_soc.c:1220:45: note: expected 'unsigned char *' but argument is of type 'const unsigned char *'
drivers/net/ethernet/ralink/mtk_eth_soc.c:1222:44: error: passing argument 2 of 'fe_hw_set_macaddr' discards 'const' qualifier from pointer target type [-Werror=discarded-qualifiers]
1222 | fe_hw_set_macaddr(priv, dev->dev_addr);
| ~~~^~~~~~~~~~
drivers/net/ethernet/ralink/mtk_eth_soc.c:155:75: note: expected 'unsigned char *' but argument is of type 'const unsigned char *'
155 | static inline void fe_hw_set_macaddr(struct fe_priv *priv, unsigned char *mac)
| ~~~~~~~~~~~~~~~^~~
cc1: all warnings being treated as errors
Signed-off-by: Nick Hainke <vincent@systemli.org>
Upstream dropped support for legacy driver [0]. Rewrite the driver like
the renesas pwm driver [1].
Fixes erros in the form of:
make: *** [/__w/openwrt/openwrt/openwrt/include/toplevel.mk:232: target/compile] Error 1
====== Make errors from logs/target/linux/compile.txt ======
| ^~~~~~~~~~~~~~
drivers/pwm/pwm-mediatek-ramips.c:107:19: note: (near initialization for 'mtk_pwm_ops.free')
drivers/pwm/pwm-mediatek-ramips.c:108:10: error: 'const struct pwm_ops' has no member named 'disable'
108 | .disable = mtk_pwm_disable,
| ^~~~~~~
drivers/pwm/pwm-mediatek-ramips.c:108:20: error: initialization of 'int (*)(struct pwm_chip *, struct pwm_device *, struct pwm_capture *, long unsigned int)' from incompatible pointer type 'void (*)(struct pwm_chip *, struct pwm_device *)' [-Werror=incompatible-pointer-types]
108 | .disable = mtk_pwm_disable,
| ^~~~~~~~~~~~~~~
drivers/pwm/pwm-mediatek-ramips.c:108:20: note: (near initialization for 'mtk_pwm_ops.capture')
cc1: all warnings being treated as errors
[0] - 0829c35dc5
[1] - ec00cd5e63
Signed-off-by: Nick Hainke <vincent@systemli.org>
Upstream dropped slave_id in dai_dma [0]. So drop it also in the mt7620
support patch.
Fixes errors in the form of:
sound/soc/ralink/ralink-i2s.c: In function 'ralink_i2s_init_dma_data':
sound/soc/ralink/ralink-i2s.c:452:17: error: 'struct snd_dmaengine_dai_dma_data' has no member named 'slave_id'
452 | dma_data->slave_id = i2s->txdma_req;
| ^~
sound/soc/ralink/ralink-i2s.c:462:17: error: 'struct snd_dmaengine_dai_dma_data' has no member named 'slave_id'
462 | dma_data->slave_id = i2s->rxdma_req;
| ^~
[0] - https://lore.kernel.org/r/20211122222203.4103644-3-arnd@kernel.org
Signed-off-by: Nick Hainke <vincent@systemli.org>
Upstream changed in ed5c2f5fd10d ("i2c: Make remove callback return void")
the i2c driver's remove function to return no value. Adapt the driver code
to compile with 5.15 and 6.1 like it is done in other projects [0].
Fixes errors in the form of:
make[8]: Leaving directory '/home/nick/openwrt/build_dir/target-mipsel_24kc_musl/linux-ramips_mt7621/linux-6.1.29'
CC drivers/pinctrl/pinctrl-aw9523.o
drivers/pinctrl/pinctrl-aw9523.c:1117:19: error: initialization of 'void (*)(struct i2c_client *)' from incompatible pointer type 'int (*)(struct i2c_client *)' [-Werror=incompatible-pointer-types]
1117 | .remove = aw9523_remove,
| ^~~~~~~~~~~~~
drivers/pinctrl/pinctrl-aw9523.c:1117:19: note: (near initialization for 'aw9523_driver.remove')
cc1: all warnings being treated as errors
[0] - https://gitlab.com/ddcci-driver-linux/ddcci-driver-linux/-/merge_requests/10/diffs
Signed-off-by: Nick Hainke <vincent@systemli.org>
Apply the "109-drivers-mt7621-dma-handle-error-from-device_reset.patch"
directly on the downstream maintained dma driver.
Signed-off-by: Nick Hainke <vincent@systemli.org>
Commit 87dd67f496f7 ("staging: mt7621-dma: remove driver from tree")
removed the mt7621-dma driver. Maintain the driver downstream in the
folder of the other mediatek drivers.
Signed-off-by: Nick Hainke <vincent@systemli.org>
Refresh kernel patches changed from the just introduced ipq60xx new
subtarget.
Patch automatically refreshed with make target/linux/refresh.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
These recipes are generic and will be used for other subtargets, so lets
move them to the target Makefile so they can reused.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Introduce support for the Qualcomm IPQ60xx SoC. WiFi support still has
to be handled and correctly fix hence this is currently marked as
source-only to have a solid base to progress on correct support of this
and hope Upstream QUIC publish newers ath11k drivers for this SoC.
Co-developed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Mantas Pucka <mantas@8devices.com>
[ improve commit description, add SoB for Robert, make it source-only ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Fix DTS error in LED color/function conversion due to a bug in the
conversion script.
Fixes: a9e0d97e1f ("ipq40xx: convert to new LED color/function format where possible")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add dtb makefile target to targets list to permit correct working of
make target/linux/dtb
Fixes: c47532b1ea ("kernel-buildOnmk: add support for compiling only DTS")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
bmips has all the dt-bindings includes inside each SoC .dtsi files, so let's
move the new includes there instead of adding them to each board .dts files.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Fix DTS error in LED color/function conversion due to a bug in the
conversion script.
Fixes: 19c45b95db ("ramips: convert to new LED color/function format where possible")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Fix DTS error in LED color/function conversion due to a bug in the
conversion script.
Fixes: 0c3f3eb229 ("lantiq: convert to new LED color/function format where possible")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Fix DTS error in LED color/function conversion due to a bug in the
conversion script.
Fixes: 33e7962329 ("ipq806x: convert to new LED color/function format where possible")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Initial conversion to new LED color/function format
and drop label format where possible. The same label
is composed at runtime.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Drop redundant label with new LED color/function format declared.
This was needed previously when the new format wasn't supported by
leds.sh functions script. Now that is supported this property
can be removed in favor of the new format.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Initial conversion to new LED color/function format
and drop label format where possible. The same label
is composed at runtime.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Drop redundant label with new LED color/function format declared.
This was needed previously when the new format wasn't supported by
leds.sh functions script. Now that is supported this property
can be removed in favor of the new format.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Initial conversion to new LED color/function format
and drop label format where possible. The same label
is composed at runtime.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Drop redundant label with new LED color/function format declared.
This was needed previously when the new format wasn't supported by
leds.sh functions script. Now that is supported this property
can be removed in favor of the new format.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Initial conversion to new LED color/function format
and drop label format where possible. The same label
is composed at runtime.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Initial conversion to new LED color/function format
and drop label format where possible. The same label
is composed at runtime.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Drop redundant label with new LED color/function format declared.
This was needed previously when the new format wasn't supported by
leds.sh functions script. Now that is supported this property
can be removed in favor of the new format.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Initial conversion to new LED color/function format
and drop label format where possible. The same label
is composed at runtime.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Drop redundant label with new LED color/function format declared.
This was needed previously when the new format wasn't supported by
leds.sh functions script. Now that is supported this property
can be removed in favor of the new format.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Initial conversion to new LED color/function format
and drop label format where possible. The same label
is composed at runtime.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Drop redundant label with new LED color/function format declared.
This was needed previously when the new format wasn't supported by
leds.sh functions script. Now that is supported this property
can be removed in favor of the new format.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Initial conversion to new LED color/function format
and drop label format where possible. The same label
is composed at runtime.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Initial conversion to new LED color/function format
and drop label format where possible. The same label
is composed at runtime.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Drop redundant label with new LED color/function format declared.
This was needed previously when the new format wasn't supported by
leds.sh functions script. Now that is supported this property
can be removed in favor of the new format.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Initial conversion to new LED color/function format
and drop label format where possible. The same label
is composed at runtime.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Initial conversion to new LED color/function format
and drop label format where possible. The same label
is composed at runtime.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Drop redundant label with new LED color/function format declared.
This was needed previously when the new format wasn't supported by
leds.sh functions script. Now that is supported this property
can be removed in favor of the new format.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Initial conversion to new LED color/function format
and drop label format where possible. The same label
is composed at runtime.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Initial conversion to new LED color/function format
and drop label format where possible. The same label
is composed at runtime.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Initial conversion to new LED color/function format
and drop label format where possible. The same label
is composed at runtime.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Drop redundant label with new LED color/function format declared.
This was needed previously when the new format wasn't supported by
leds.sh functions script. Now that is supported this property
can be removed in favor of the new format.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Backport patch fixing kernel panic with mcast packets, patch is already
scheduled to be backported to stable kernels and will be dropped once
new stable kernel version are released.
Fixes: #14554
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The rtl93xx SoC supports both 1000Base-X and 10GBase-CR on its SerDes
interfaces. Enable dynamic switching between mac-signaled modes to
support 1000Base-X and 10GBase-CR on the SFP port.
Signed-off-by: Tobias Schramm <tobias@t-sys.eu>
This patch adds support for 1000Base-X and 10GBase-CR directly on the
SerDes lanes of rtl93xx SoCs.
This fixes SFP/SFP+ support on devices like the XSG1250-12.
Signed-off-by: Tobias Schramm <tobias@t-sys.eu>
Backport patch to enable PHYLIB_LEDS kconfig dynamically instead of
having to select this config for every target that makes use of PHY LEDs
API.
All affected patch are automatically refreshed.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
CONFIG_PHYLIB_LEDS is required in order for phylib to probe the DT for LEDs
attached to PHY-s.
Fixes: 75ad5c2 ("qualcommax: switch to qca8081 upstream PHY driver")
Signed-off-by: Robert Marko <robimarko@gmail.com>
Commit daefc646e6 ("realtek: fix ZyXEL initramfs image generation")
fixed a shell expansion issue with zyxel-vers usage. Commit 045baca10b
("realtek: deduplicate GS1900 recipes") took care of this for the
rtl838x and rtl839x subtargets, but the single device officially
supported in rtl930x - the XGS1250-12 - was overlooked. This commit
updates the XGS1250-12 build recipe as well.
Signed-off-by: Stijn Segers <foss@volatilesystems.org>
Add even more missing Kconfig for video-core introduced by recent fixup
to video kmods.
Fixes: 76b0d24157 ("kernel: modules: video: fix video-core for 6.1")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Backport one patch merged upstream that prevent a deadlock for LED
netdev trigger and add a pending patch that fix kernel panic on
interface rename trigger notification with invalid dev.
Fixes: #14477
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add missing Kconfig for video-core introduced by recent fixup to video
kmods.
Fixes: 76b0d24157 ("kernel: modules: video: fix video-core for 6.1")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Linux 6.1 wraps core video drivers in a MEDIA_PLATFORM_DRIVERS submenu.
Enable that for 6.1 and add some new necessary undefines to
target/linux/generic/config-6.1 to avoid build failures.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
This adds support for the Fritzbox 3490 device. It contains two
SoCs, one Lantiq with a 5GHz WiFi and one QCA9558 with 2.4GHz
and 5 GHz WiFi. Only the Lantiq has access to the flash memory,
the Atheros runs fully from RAM and is booted by using a remoteproc
kernel module which is not supported with this commit.
The devices were manufactured with varying NAND chips which
requires Micron and non-Micron versions of the images.
Specifications:
- SoC: Lantiq 500 MHz
- RAM: 256 MB
- Storage: 512 MB NAND, 1MB FLASH
- Wireless, separate SOC QCA9558 with 128MB RAM (not supported yet):
· Qualcomm-QCA9558 w/ 3×3 MIMO for 2.4GHz 802.11b/g/n
· Qualcomm-QCA9880 w/ 3×3 MIMO for 5GHz 802.11a/ac
· AG71xx ethernet
- Ethernet: Built-in AR 803x, 7 port 4 phy switch,
4x 1000/100/10 port, Port 5 is fixed and connected to the WASP SOC
- Renesas µPD720202 USB3 PCIe, requires firmware binary on the device
- VDSL2 modem
- Without telephony or ISDN
Installation:
Check which NAND the device has by using the following procedure with
stock firmware:
Go to to http://<fritzbox_ip>/support.lua, download the support data
file and search for string "NAND device" to get the manufacturer kernel
output.
Use Micron image if Micron is displayed otherwise the non-Micron image.
Use the eva_ramboot.py script to boot the initramfs image. Follow the
procedure to interrupt booting by ftp into 192.168.178.1 within
5 seconds after poweron.
Then transfer the sysupgrade image to the device and run sysupgrade to
flash it to the NAND.
For making USB work, an renesas xhci firmware file (e.g. v2026) is
needed and it should be copied to /lib/firmware/ (file name
renesas_usb_fw.mem).
Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
This adds support for the Fritzbox 5490/5491 devices. They contain
two SoCs, one Lantiq without WiFi and one QCA9558 with 2.4GHz
and 5 GHz WiFi. Only the Lantiq has access to the flash memory,
the Atheros runs fully from RAM and is booted by using a remoteproc
kernel module which is not supported with this commit.
Both devices have fiber WAN ports.
The devices were manufactured with varying NAND chips which
requires Micron and non-Micron versions of the images.
Specifications:
- SoC: Lantiq 500 MHz
- RAM: 256 MB
- Storage: 512 MB NAND, 1MB FLASH
- Wireless, separate SOC QCA9558 with 128MB RAM (not supported yet):
· Qualcomm-QCA9558 w/ 3×3 MIMO for 2.4GHz 802.11b/g/n
· Qualcomm-QCA9880 w/ 3×3 MIMO for 5GHz 802.11a/ac
· AG71xx ethernet
- Ethernet: Built-in AR 803x, 7 port Lantiq gswip switch,
4x 1000/100/10 port (additional qca8334 switch for 2 ports), Port 5 is
fixed and connected to the Wireless SOC
- Renesas µPD720202 USB3 PCIe, requires firmware binary on the device
- AT 8033 based AON fiber port (5490) or GPON fiber port (5491)
Unsupported:
- DECT and ISDN telephony
- Two ethernet ports (on extra switch) and fiber port not working
Installation:
Check which NAND the device has by using the following procedure with
stock firmware:
Go to to http://<fritzbox_ip>/support.lua, download the support data
file and search for string "NAND device" to get the manufacturer kernel
output.
Use Micron image if Micron is displayed otherwise the non-Micron image.
Use the eva_ramboot.py script to boot the initramfs image. Follow the
procedure to interrupt booting by ftp into 192.168.178.1 within
5 seconds after poweron.
Then transfer the sysupgrade image to the device and run sysupgrade to
flash it to the NAND.
For making USB work, an renesas xhci firmware file (e.g. v2026) is
needed and it should be copied to /lib/firmware/ (file name
renesas_usb_fw.mem).
Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
This adds support for the Fritzbox 7490 device. It contains two
SoCs, one Lantiq without WiFi and one QCA9558 with 2.4GHz
and 5 GHz WiFi. Only the Lantiq has access to the flash memory,
the Atheros runs fully from RAM and is booted by using a remoteproc
kernel module and is not supported with this commit.
The devices were manufactured with varying NAND chips which
requires Micron and non-Micron versions of the images.
Specifications:
- SoC: Lantiq 500 MHz
- RAM: 256 MB
- Storage: 512 MB NAND, 1MB FLASH
- Wireless, separate SOC QCA9558 with 128MB RAM (not supported yet):
· Qualcomm-QCA9558 w/ 3×3 MIMO for 2.4GHz 802.11b/g/n
· Qualcomm-QCA9880 w/ 3×3 MIMO for 5GHz 802.11a/ac
· AG71xx ethernet
- Ethernet: Built-in AR 803x, 7 port 4 phy switch,
4x 1000/100/10 port, Port 5 is fixed and connected to the WASP SOC
- Renesas µPD720202 USB3 PCIe, requires firmware binary on the device
- VDSL2 modem
Unsupported:
- DECT and ISDN telephony
Installation:
Check which NAND the device has by using the following procedure with
stock firmware:
Go to to http://<fritzbox_ip>/support.lua, download the support data
file and search for string "NAND device" to get the manufacturer kernel
output.
Use Micron image if Micron is displayed otherwise the non-Micron image.
Use the eva_ramboot.py script to boot the initramfs image. Follow the
procedure to interrupt booting by ftp into 192.168.178.1 within
5 seconds after poweron.
Then transfer the sysupgrade image to the device and run sysupgrade to
flash it to the NAND.
For making USB work, an renesas xhci firmware file (e.g. v2026) is
needed and it should be copied to /lib/firmware/ (file name
renesas_usb_fw.mem).
Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
The Fritzbox 3490, 5490 and 7490 devices have a Renesas µPD720202
USB3 PCIe device, which requires an endian switch for PCIe slave
devices. The flag and setting is not implemented in the available
patches. Since adding this setting would break other devices,
a DTB setting lantiq,switch-pcie-endianess is added for selective
enablement.
Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
Comfast CF-E393AX is a dual-band Wi-Fi 6 POE ceiling mount access point.
Oem firmware is a custom openwrt 21.02 snapshot version.
We can gain access via ssh once we remove the root password.
Hardware specification:
SoC: MediaTek MT7981A 2x A53
Flash: 128 MB SPI-NAND
RAM: 256MB DDR3
Ethernet: 1x 10/100/1000 Mbps built-in PHY (WAN)
1x 10/100/1000/2500 Mbps MaxLinear GPY211C (LAN)
Switch: MediaTek MT7531AE
WiFi: MediaTek MT7976D
LEDS: 1x (Red, Blue and Green)
Button: Reset
UART: 3.3v, 115200n8
--------------------------
| Layout |
| ----------------- |
| 4 | VCC GND TX RX | <= |
| ----------------- |
--------------------------
Gain SSH access:
1. Login into web interface (http://apipaddress/computer/login.html),
and download the
configuration(http://apipaddress/computer/config.html).
2. Rename downloaded backup config - 'backup.file to backup.tar.gz',
Enter 'fakeroot' command then decompress the configuration:
tar -zxf backup.tar.gz
3. Edit 'etc/shadow', update (remove) root password:
With password =
'root:$1$xf7D0Hfg$5gkjmvgQe4qJbe1fi/VLy1:19362:0:99999:7:::'
'root:$1$xf7D0Hfg$5gkjmvgQe4qJbe1fi/VLy1:19362:0:99999:7:::'
to
Without password =
'root::0:99999:7:::'
'root::0:99999:7:::'
4. Repack 'etc' directory back to a new backup file:
tar -zcf backup-ssh.tar.gz etc/
5. Rename new config tar.gz file to 'backup-ssh.file'
Exit fakeroot - 'exit'
6. Upload new configuration via web interface, now you
can SSH with the following:
'ssh -vv -o HostKeyAlgorithms=+ssh-rsa \
-o PubkeyAcceptedAlgorithms=+ssh-rsa root@192.168.10.1'.
Backup the mtd partitions
- https://openwrt.org/docs/guide-user/installation/generic.backup
7. Copy openwrt factory firmware to the tmp folder to install via ssh:
'scp -o HostKeyAlgorithms=+ssh-rsa \
-o PubkeyAcceptedAlgorithms=+ssh-rsa \
*-mediatek-filogic-comfast_cf-e393ax-squashfs-factory.bin \
root@192.168.10.1:/tmp/'
'sysupgrade -n -F \
/tmp/*--mediatek-filogic-comfast_cf-e393ax-squashfs-factory.bin'
8. Once led has stopped flashing - Connect via ssh with the
default openwrt ip address - 'ssh root@192.168.1.1'
9. SSH copy the openwrt sysupgrade firmware and upgrade
as per the default instructions.
Signed-off-by: David Bentham <db260179@gmail.com>
Specifications:
lan: eth0
wan: eth1
Problem Description:
The lan wan port is reversed with the current machine.
Use eth0 as LAN port and eth1 as WAN port.
Signed-off-by: Weiping Yang <weiping.yang@gl-inet.com>
The driver for the cellular modems serial interface and qmi was missing
from the default device packages. The driver is required to interact
with the modem using AT commands.
Signed-off-by: Jan Fuchs <jf@simonwunderlich.de>
Backport PHY package MMD patch merged upstream that add support for
writing MMD regs for the PHY package and support for writing to PHY
package at an offset.
All affected patches automatically refreshed.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This patch converts ath10k calibration data to NVMEM format for
wave 1 devices with mtd ASCII MAC address. The "calibration"
NVMEM cell size is 0x844. All unportable MAC address settings
have been moved to '10_fix_wifi_mac' scripts.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
This patch converts ath10k calibration data to NVMEM format for
wave 1 devices with mtd binary MAC address. The "calibration"
NVMEM cell size is 0x844. The MAC addresses are assigned via dts.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
This patch converts ath10k calibration data to NVMEM format for
wave 1 devices with built-in MAC address. The "calibration"
NVMEM cell size is 0x844.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
This patch converts ath10k pre-calibration data to NVMEM format for
wave 2 devices with mtd ASCII MAC address. The "pre-calibration"
NVMEM cell size is 0x2f20. All unportable MAC address settings have
been moved to '10_fix_wifi_mac' scripts.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
This patch converts ath10k pre-calibration data to NVMEM format for
wave 2 devices with mtd binary MAC address. The "pre-calibration"
NVMEM cell size is 0x2f20. The MAC addresses are assigned via dts.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
This patch converts ath10k pre-calibration data to NVMEM format for
wave 2 devices with built-in MAC address. The "pre-calibration"
NVMEM cell size is 0x2f20.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
The ath10k driver will load both pre-calibration data and board-2.bin
if board-2.bin exists. So it's not necessary to remove it. And this
change won't increase jffs2 image size.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Backport at803x split patches merged upstream to tidy things up for the
at803x PHY driver.
New Kernel config are introduced hence any user needs to be updated.
Downstream ipq40xx patch require rework to correctly move them to the
qcom specific PHY directory.
All affected patch automatically refreshed.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Only bcm2708 and bcm2709 use "kernel.img" file name.
bcm2710 and bcm2711 use "kernel8.img" and bcm2712 uses "kernel_2712.img".
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Automatically detect boot partition instead of forcing /dev/mmcblk0p1.
This way users can still get /boot mounted when booting from USB.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Add missing Rasoberry Pi 5 board_name to set_preinit_iface in order to get
ethernet working on failsafe mode.
Fixes: 8b63d9a ("bcm27xx: add new bcm2712 subtarget")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* fix switch ports with modes other than 1000M/Full
* set 32-bit dma_coherent_mask to get PPE to work with 4 GiB of RAM
* sync driver for built-in 1GE PHY with MediaTek SDK sources
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The qca8081 phy needs to set the reset delay time,
otherwise it will not be detected by the mdio bus.
Fixes: 75ad5c2 ("qualcommax: switch to qca8081 upstream PHY driver")
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Switch to qca8081 upstream PHY. Update every device that have LEDs
attached to the qca8081 PHY to follow new way of defining the LEDs and
add original OEM configuration.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Backport upstream patch adding more speed modes to LED netdev trigger.
Fixes: 2c39269b6e ("generic: 6.1: backport qca808x LED support patch")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Backport qca808x LED support patch merged upstream needed to drop
handling of it from the SSDK for ipq807x target.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Backport merged upstream patch that adds support for firmware loader
from NVMEM or attached filesystem for Aquantia PHYs.
Refresh all kernel patches affected by this change.
Also update the path for aquantia .ko that got moved to dedicated
directory upstream.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
[rmilecki: port to 5.15]
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
They are unnecessary since ipq806x switched to DSA in
the commit 337e36e0ef.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Reviewed-by: Robert Marko <robimarko@gmail.com>
Refresh HSGMII patch due to recent PHY backport that cause
compilation warning for case not handled in phy_interface_num_ports.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Refresh 2.5G-SGMII patch due to recent PHY backport that cause
compilation warning for case not handled in phy_interface_num_ports.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
In order to get rid of having to modify U-boot bootcmd and having U-boot
load the Aquantia PHY-s firmware lets use some of the free space on SPI-NOR
to add a second ethphyfw partition and be able to load AQR FW via NVMEM
cells.
Signed-off-by: Robert Marko <robimarko@gmail.com>
It seems that the reset GPIO-s defined for the two AQR PHY-s are actually
reversed.
Manually testing confirmed that GPIO44 is actually reset GPIO of AQR at 0,
while GPIO59 is reset of AQR at 8:
root@OpenWrt:~# mdio 9*
DEV PHY-ID LINK
0x00 0x00000000 down
0x08 0x00000000 down
0x10 0x004dd0b1 down
0x11 0x004dd0b1 down
0x12 0x004dd0b1 down
0x13 0x004dd0b1 up
0x14 0x004dd0b1 down
0x15 0x04820a05 down
root@OpenWrt:~# gpioset gpiochip0 44=0
root@OpenWrt:~# mdio 9*
DEV PHY-ID LINK
0x08 0x00000000 down
0x10 0x004dd0b1 down
0x11 0x004dd0b1 down
0x12 0x004dd0b1 down
0x13 0x004dd0b1 up
0x14 0x004dd0b1 down
0x15 0x04820a05 down
root@OpenWrt:~# gpioset gpiochip0 44=1
root@OpenWrt:~# mdio 9*
DEV PHY-ID LINK
0x00 0x00000000 down
0x08 0x00000000 down
0x10 0x004dd0b1 down
0x11 0x004dd0b1 down
0x12 0x004dd0b1 down
0x13 0x004dd0b1 up
0x14 0x004dd0b1 down
0x15 0x04820a05 down
root@OpenWrt:~# gpioset gpiochip0 59=0
root@OpenWrt:~# mdio 9*
DEV PHY-ID LINK
0x00 0x00000000 down
0x10 0x004dd0b1 down
0x11 0x004dd0b1 down
0x12 0x004dd0b1 down
0x13 0x004dd0b1 up
0x14 0x004dd0b1 down
0x15 0x04820a05 down
root@OpenWrt:~# gpioset gpiochip0 59=1
root@OpenWrt:~# mdio 9*
DEV PHY-ID LINK
0x00 0x00000000 down
0x08 0x00000000 down
0x10 0x004dd0b1 down
0x11 0x004dd0b1 down
0x12 0x004dd0b1 down
0x13 0x004dd0b1 up
0x14 0x004dd0b1 down
0x15 0x04820a05 down
Signed-off-by: Robert Marko <robimarko@gmail.com>
Now that we have support for firmware loading via the kernel driver, it
makes sense to populate the firmware name as well, so if its present the
driver can load it.
In later patches, loading the FW via NVMEM will be added as well.
Signed-off-by: Robert Marko <robimarko@gmail.com>
This patch adds support for Raspberry Pi 5.
Instead of using 16K pages like Raspberry Pi OS, OpenWrt uses 4K pages due to
incompatibilities with F2FS and other applications.
There are multiple RPi forum posts with different cases and users are forcing
kernel8.img to workaround them, which is the 64 bit kernel of the RPi 4.
However, this isn't possible in OpenWrt because we only ship one kernel and we
would have to add RPi 5 support to bcm2711 subtarget (RPi 4) for that
workaround to work in OpenWrt.
Specification:
- Processor Broadcom BCM2712 2.4GHz quad-core 64-bit Arm Cortex-A76 CPU,
with cryptographic extension, 512KB L2 caches per core, 2048KB L3 cache
Features:
- VideoCore VII GPU, supports OpenGL ES 3.1, Vulkan 1.2
- Dual 4Kp60 HDMI display output with HDR support 4Kp60 HEVC decoder
- LPDDR4X-4267 SDRAM 4GB and 8GB
- Dual-band 802.11ac Wi-Fi
- Bluetooth 5.0 / Bluetooth Low Energy
- microSD card slot, with support for SDR104 high-speed mode
- 2 x USB 3.0 ports
- 2 x USB 2.0 ports
- Gigabit Ethernet
- 2 x 4 lane MIPI camera/display
- PCIe 2.0 x1
- 5V/5A power via USB-C
- Raspberry Pi standard 40-pin header
- Real-time clock RTC
- Power button
Build system: x86_64
Build-tested: bcm2712
Run-tested: bcm2712/RPi5
Signed-off-by: Marty Jones <mj8263788@gmail.com>
[Remove device variant, improve description]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Add support for BCM2712 (Raspberry Pi 5).
3bb5880ab3
Patches were generated from the diff between linux kernel branch linux-6.1.y
and rpi-6.1.y from raspberry pi kernel source:
- git format-patch linux-6.1.y...rpi-6.1.y
Build system: x86_64
Build-tested: bcm2708, bcm2709, bcm2710, bcm2711
Run-tested: bcm2710/RPi3B, bcm2711/RPi4B
Signed-off-by: Marty Jones <mj8263788@gmail.com>
[Remove applied and reverted patches, squash patches and config commits]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Ubiquiti Rocket M XW is a single-band, 2x2:2 external Wi-Fi AP, with optional
GPS receiver, with two external RP-SMA antenna connections, based on
AR9342 SoC. Two band variants exists, for 2.4GHz and 5GHz band, usable
with the same image.
Specs:
- CPU: Atheros AR9342 MIPS SoC at 535MHz
- RAM: 64MB DDR400
- ROM: 8MB SPI-NOR in SO16W package, MX25L6408E
- Wi-Fi Atheros AR9342 built-in 2x2:2 radio
- Ethernet: Atheros AR8035 PHY, limited to 100Mbps speeds due to
magnetics
- Power: 24V passive PoE input.
Installation: please refer to Ubiquiti Bullet M2HP for documentation.
The device runs with exactly same image as the Bullet, and after fixes
in preceding commit, is fully functional again. Add the alternative name
to the build system.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Since commit 6f2e1b7485 ("ath79: disable delays on AT803X config init")
Ubiquiti XW boards equipped with AR8035 PHY suffered from lack of
outbound traffic on the Ethernet port. This was caused by the fact, the
U-boot has set this during boot and it wasn't reset by the PHY driver,
and the corresponding setting in device tree was wrong.
Set the 'phy-mode = "rgmii-txid"' at the ð0, and drop this property
from PHY node, as it is not parsed there. This causes the device to
connect using Ethernet once again.
Fixes: db4b6535f8 ("ath79: Add support for Ubiquity Bullet M (XW)")
Fixes: 6f2e1b7485 ("ath79: disable delays on AT803X config init")
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Onboard AR8035 PHY supports 1000Base-T operation, but onboard
Ethernet magnetics do not. Reduce advertised link speeds to 100Mbps and
lower.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Add support for loading Aquantia FW from NVMEM for Zyxel NBG7815
restoring correct functionality of the 10g port.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add pending patch for ipq4019 MDIO MDC rate fix. The divisor was never
actually set resulting in the MDC rate running at a very low speed.
The same MDIO is used on ipq807x where Aquantia PHY are commonly used
where MDIO is used to load the PHY firmware. Running at higher speed is
required to make the firmware load faster as it does reduce load time
from 60+ second to 5-6 seconds.
Add as pending as upstream there seems to be some conflicts with quic
and me and it might take lots of time before this is effectively merged
upstream.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The safe max frame size for this ethernet switch is 1532 bytes,
excluding the DSA TAG and extra VLAN header, so the maximum
outgoing frame is 1542 bytes.
The available overhead is needed when using the DSA switch with
a cascaded Marvell DSA switch, which is something that exist in
real products, in this case the Inteno XG6846.
Use defines at the top of the size for max MTU so it is clear how
we think about this, add comments.
We need to adjust the RX buffer size to fit the new max frame size,
which is 1542 when the DSA tag (6 bytes) and VLAN header (4 extra
bytes) is added.
We also drop this default MTU:
#define ENETSW_TAG_SIZE (6 + VLAN_HLEN)
ndev->mtu = ETH_DATA_LEN + ENETSW_TAG_SIZE;
in favor of just:
ndev->mtu = ETH_DATA_LEN;
I don't know why the default MTU is trying to second guess the
overhead required by DSA and VLAN but the framework will also
try to bump the MTU for e.g. DSA tags, and the VLAN overhead is
not supposed to be included in the MTU, so this is clearly not
right.
Before this patch (on the lan1 DSA port in this case):
dsa_slave_change_mtu: master->max_mtu = 9724, dev->max_mtu = 10218, DSA overhead = 8
dsa_slave_change_mtu: master = extsw, dev = lan1
dsa_slave_change_mtu: master->max_mtu = 1510, dev->max_mtu = 9724, DSA overhead = 6
dsa_slave_change_mtu: master = eth0, dev = extsw
dsa_slave_change_mtu new_master_mtu 1514 > mtu_limit 1510
mdio_mux-0.1:00: nonfatal error -34 setting MTU to 1500 on port 0
My added debug prints before the nonfatal error: the first switch from the top
is the Marvell switch, the second in the bcm6368-enetsw with its 1510 limit.
After this patch the error is gone.
OpenWrt adds a VLAN to each port so we get VLAN tags on all frames. On this
setup we even have 4 more bytes left after the two DSA tags and VLAN so
we can go all the way up to 1532 as MTU.
Testing the new 1532 MTU:
eth0 ext1 enp7s0
.--------. .-----------. cable .------.
| enetsw | <-> | mv88e6152 | <-----> | host |
`--------´ `-----------´ `------´
On the router we set the max MTU for test:
ifconfig eth0 mtu 1520
ifconfig br-wan mtu 1520
ifconfig ext1 mtu 1506
An MTU of 1506 on ext1 is a logic consequence of the above setup:
this is the max bytes actually transferred. The framing added will be:
- 18 bytes standard ethernet header
- 4 bytes VLAN header
- 6 bytes DSA tag for enetsw
- 8 bytes DSA tag for mv88e6152
Sum: 1506 + 18 + 4 + 6 + 8 = 1542 which is out max frame size.
Test pinging from host:
ping -s 1478 -M do 192.168.1.220
PING 192.168.1.220 (192.168.1.220) 1478(1506) bytes of data.
1486 bytes from 192.168.1.220: icmp_seq=1 ttl=64 time=0.696 ms
1486 bytes from 192.168.1.220: icmp_seq=2 ttl=64 time=0.615 ms
Test pinging from router:
PING 192.168.1.2 (192.168.1.2): 1478 data bytes
1486 bytes from 192.168.1.2: seq=0 ttl=64 time=0.931 ms
1486 bytes from 192.168.1.2: seq=1 ttl=64 time=0.810 ms
The max IP packet without headers is 1478, the outgoing ICMP packet is
1506 bytes. Then the DSA, VLAN and ethernet overhead is added.
Let us verify the contents of the resulting ethernet frame of 1542 bytes.
Ping packet on router side as viewed with tcpdump:
00:54:51.900869 AF Unknown (1429722180), length 1538:
0x0000: 3d93 bcae c56b a83d 8874 0300 0004 8100 =....k.=.t......
0x0010: 0000 dada 0000 c020 0fff 0800 4500 05e2 ............E...
0x0020: 0000 4000 4001 b0ec c0a8 0102 c0a8 01dc ..@.@...........
0x0030: 0800 7628 00c3 0001 f5da 1d65 0000 0000 ..v(.......e....
0x0040: ce65 0a00 0000 0000 1011 1213 1415 1617 .e..............
0x0050: 1819 1a1b 1c1d 1e1f 2021 2223 2425 2627 .........!"#$%&'
0x0060: 2829 2a2b 2c2d 2e2f 3031 3233 3435 3637 ()*+,-./0123456
(...)
- 3d93 = First four bytes are the last two bytes of the destination
ethernet address I don't know why the first four are missing,
but it sure explains why the paket is 1538 bytes and not 1542
which is the actual max frame size.
- bcae c56b a83b = source ethernet address
- 8874 0300 0004 = Broadcom enetsw DSA tag
- 8100 0000 = VLAN 802.1Q header
- dada 0000 c020 0fff = EDSA tag for the Marvell (outer) switch,
- 0800 is the ethertype (part of the EDSA tag technically)
- Next follows the contents of the ping packet as it appears if
we dump it on the DSA interface such as tcpdump -i lan1
etc, there we get the stripped out packet, 1506 bytes.
- At the end 4 bytes of FCS.
This clearly illustrates that the DSA tag is included in the MTU
which we set up in Linux, but the VLAN tag and ethernet headers and
checksum is not.
Tested-by: Paul Donald <newtwen@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
This reverts commit dcdcfc1511.
This is a firmware for third-party u-boot mod, which should not
be carried here by us.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
The current dts file of dgs-1210-10p doesn't support link states
for the sfp ports (they are always up).
This patch tries to give better support for this and was run tested
on dgs-1210-10p.
It was heavily inspired from Paul Fertser, RaylynnKnight
and the author of dgs-1210-10mp-f.dts
https://forum.openwrt.org/t/dlink-dgs-1210-10p-with-glc-t-co-sfp/170928
Signed-off-by: Michel Thill <jmthill@gmail.com>
Commit e816591e22 ("ath79: qca: convert to nvmem-layout") mistakenly
switched the source of the mac address from the 'info' to 'art'
partition.
This patch updates all devices that share same 'parent' device tree file
and was tested to fix the problem for eap225-outdoor-v3 - device that I
actually own.
Fixes: e816591e22 ("ath79: qca: convert to nvmem-layout")
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
[amend commit message]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Enabling SMP on Danube[1] is incompatible with a patch that
adds support for interrupt handling on all cores on other
platforms[2]. This patch fixes the mentioned issue.
1. 084c20f6c5 ("lantiq: xway: kernel: enable SMP support ")
2. fbd33d6164 ("lantiq: enable interrupts on second VPEs")
Fixes: #13934Fixes: #14283
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
By default Linux will default to most IRQ-s being mapped to core 0 which
during high loads will completely swamp the core 0, so lets add the widely
used script that has been floating around forums for a long time to try and
optimize the IRQ mapping a bit.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Some of devices in this target have only 8 MiB space and are closing to
borders of usable space. Particularly, TP-Link RE305 v1 already suffers
from this issue[1], where with current partition layout, on release
images, there's not enough space for overlay. So activate small_flash
feature, which will remove some userspace hardening but will gain almost
1 MiB additional flash memory space. Here is small size comparison of
similar device (RE365 v1) with default config + LuCI:
kernel rootfs sysupgrade
current: 2305728 3635044 5964584
small_flash: 1713571 3320132 5047080
1. https://github.com/openwrt/openwrt/issues/14215
Suggested-by: Sander Vanheule <sander@svanheule.net>
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Renumber backport patches starting from 000 to tidy things up.
Also fix patch name format for the mmc backport patch.
Refresh patches affected by this renumber change.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Move stmmac backport fix patches from ipq806x to generic backport
directory as they got merged upstream and they fix wide performance
regression.
This will eventually cause performance increase on any user of the
stmmac driver.
Generic patch automatically refreshed with make target/linux/refresh.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add support for Ubiquiti LiteBeam M5 (XW).
The device was previously supported in ar71xx.
See commit: https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=d0988235dd277b9a832bbc4b2a100ac6e821f577
Add ALTX_MODEL for Ubiquiti AirGrid M5 HP (XW), Ubiquiti PowerBeam M5 300 (XW) in generic-ubnt.mk
This models are identical (firmware-wise) to the already supported Ubiquiti Nanostation Loco M (XW)
Add also Ubiquiti NanoBeam M5 to ALTX_MODEL of Ubiquiti Nanostation Loco M (XW) since it's another clone.
Tested on:
- Ubiquiti LiteBeam M5 (XW)
- Ubiquiti PowerBeam M5 (XW)
This also modify target/ath79/dts/ar9342_ubnt_xw.dtsi to use nvmem for calibration data
Checked that the caldata size in the eeprom partition are actually 0x440 on:
- Ubiquiti PowerBeam M5 (XW)
- Ubiquiti Nanostation M5 (XW)
- Ubiquiti LiteBeam M5 (XW)
- Ubiquiti AirGrid M5 HP (XW)
Signed-off-by: Samuele Longhi <agave@dracaena.it>
Booting from non-MMC devices on Rockchip targets without this
change results in a boot failure:
Model: FriendlyElec NanoPi R5S
Net: eth0: ethernet@fe2a0000
Hit any key to stop autoboot: 0
** Booting bootflow 'nvme#0.blk#1.bootdev.part_1' with script
** No partition table - mmc 0 **
** No partition table - mmc 0 **
Couldn't find partition mmc 0:1
Can't set block device
Wrong Image Type for bootm command
ERROR -91: Protocol wrong type for socket: can't get kernel image!
Boot failed (err=1)
This change fixes the default boot script for Rockchip targets to
support booting from non-MMC devices such as NVMe or USB drives.
Some targets with only a boot rom (e.g. NanoPi R5S) may require u-boot
to be installed on the eMMC or a MicroSD card in order to boot from
non-MMC devices.
Fixes: #14420
Reviewed-by: Tianling Shen <cnsztl@immortalwrt.org>
Signed-off-by: Justin Klaassen <justin@tidylabs.app>
The WLAN + WED reset sequence relies on being able to receive interrupts from
the card, in order to synchronize individual steps with the firmware.
When WED is stopped, leave interrupts running and rely on the driver turning
off unwanted ones.
WED DMA also needs to be disabled before resetting.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
