Commit Graph

27640 Commits

Author SHA1 Message Date
Olliver Schinagl
68e28cdc47 realtek: timer: Activate for RTL930x devices
Use the new timer driver for the RTL930x devices.

Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
[remove old clock provider, select MIPS_EXTERNAL_TIMER and refresh
kernel config]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
2023-01-28 17:30:26 +01:00
Sander Vanheule
38cba61bff
realtek: timer: Register enabled scheduler clock
Before calling sched_clock_register(), the timer used to drive the
scheduling clock should already be enabled. Otherwise the kernel log
will show strange time jumps during, and the watchdog might not be
pinged in a timely fashion, resulting in reboots.

[    0.160281] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[   78.104319] clocksource: Switched to clocksource realtek_otto_timer

Fixes: 3cc8011171 ("realtek: resurrect timer driver")
Signed-off-by: Sander Vanheule <sander@svanheule.net>
2023-01-28 15:23:03 +01:00
Zoltan HERPAI
6e428a8490 mxs: fix SD-card image generation for OLinuXino boards
Fixes: mxs: add generic subtarget (64ef920)

Adding the generic target caused the TARGET_BOOTFS_PARTSIZE to stay
hidden for these boards, crashing the FAT filesystem creation.

Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
2023-01-27 23:19:38 +01:00
Olliver Schinagl
7f5edeb8bd realtek: eth: Fix missing end of comment marker
Because this comment is followed by another comment, nothing luckily
breaks, so only a cosmetic change.

Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
2023-01-27 22:03:17 +01:00
Shiji Yang
cfb296b79a ath79: add support for D-Link DIR-629 A1
Specifications:
  SOC:      QCA9588 CPU 720 MHz AHB 200 MHz
  Switch:   AR8236
  RAM:      64 MiB DDR2-600
  Flash:    8 MiB
  WLAN:     Wi-Fi4 2.4 GHz 3*3
  LAN:      LAN ports *4
  WAN:      WAN port *1
  Buttons:  reset *1 + wps *1
  LEDs: ethernet *5, power, wlan, wps

MAC Address:
  use      address               source
  label    70:62:b8:xx:xx:96     lan && wlan
  lan      70:62:b8:xx:xx:96     mfcdata@0x35
  wan      70:62:b8:xx:xx:97     mfcdata@0x6a
  wlan     70:62:b8:xx:xx:96     mfcdata@0x51

Install via Web UI:
  Apply factory image in the stock firmware's Web UI.

Install via Emergency Room Mode:
  DIR-629 A1 will enter recovery mode when the system fails to boot or
  press reset button for about 10 seconds.

  First, set IP address to 192.168.0.1 and server IP to 192.168.0.10.
  Then we can open http://192.168.0.1 in the web browser to upload
  OpenWrt factory image or stock firmware. Some modern browsers may
  need to turn on compatibility mode.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2023-01-26 00:32:36 +01:00
John Audia
4e9365a654 kernel: bump 5.15 to 5.15.90
All patches automatically rebased.

Build system: x86_64
Build-tested: bcm2711/RPi4B, filogic/xiaomi_redmi-router-ax6000-ubootmod
Run-tested: bcm2711/RPi4B, filogic/xiaomi_redmi-router-ax6000-ubootmod

Signed-off-by: John Audia <therealgraysky@proton.me>
2023-01-26 00:16:00 +01:00
Sander Vanheule
8f47b87b0c realtek: rtl931x: drop LINKER_LOAD_ADDRESS bypass
RTL931x kernel builds were patched to bypass the LINKER_LOAD_ADDRESS
parameter, and hardcode it to 0x80220000. This doesn't make much sense,
since value of LINKER_LOAD_ADDRESS, load-ld, only appears to be a copy
of load-y, adjusted to the linker's taste.

Dropping the hacks for bypassing LINKER_LOAD_ADDRESS results in a kernel
that actually starts booting on an RTL9313 (Netgear MS510TXM), but
currently still hangs when the kernel switches timers.

Signed-off-by: Sander Vanheule <sander@svanheule.net>
2023-01-25 22:39:35 +01:00
Wenli Looi
7396263680 ath79: convert Netgear EX7300 caldata to nvmem
Transition to specify caldata in the DTS.

Signed-off-by: Wenli Looi <wlooi@ucalgary.ca>
2023-01-25 00:42:52 +01:00
Wenli Looi
f0eb73a888 ath79: consolidate Netgear EX7300 series images
This change consolidates Netgear EX7300 series devices into two images
corresponding to devices that share the same manufacturer firmware
image. Similar to the manufacturer firmware, the actual device model is
detected at runtime. The logic is taken from the netgear GPL dumps in a
file called generate_board_conf.sh.

Hardware details for EX7300 v2 variants
---------------------------------------
SoC: QCN5502
Flash: 16 MiB
RAM: 128 MiB
Ethernet: 1 gigabit port
Wireless 2.4GHz (currently unsupported due to lack of ath9k support):
- EX6250 / EX6400 v2 / EX6410 / EX6420: QCN5502 3x3
- EX7300 v2 / EX7320: QCN5502 4x4
Wireless 5GHz:
- EX6250: QCA9986 3x3 (detected by ath10k as QCA9984 3x3)
- EX6400 v2 / EX6410 / EX6420 / EX7300 v2 / EX7320: QCA9984 4x4

Signed-off-by: Wenli Looi <wlooi@ucalgary.ca>
2023-01-25 00:42:52 +01:00
John Audia
257e9fc57c kernel: bump 5.10 to 5.10.165
All patches automatically rebased.

Build system: x86_64
Build-tested: ramips/tplink_archer-a6-v3
Run-tested: ramips/tplink_archer-a6-v3

Signed-off-by: John Audia <therealgraysky@proton.me>
2023-01-24 23:08:43 +01:00
John Audia
9c3954bc46 kernel: bump 5.10 to 5.10.164
All patches automatically rebased

Build system: x86_64
Build-tested: ramips/tplink_archer-a6-v3
Run-tested: ramips/tplink_archer-a6-v3

Signed-off-by: John Audia <therealgraysky@proton.me>
2023-01-24 23:08:43 +01:00
Lorenz Brun
bec9e79a99 realtek: dsa: support active-high LEDs
The TP-LINK TL-ST1008F has active-high LEDs, so we need a device tree
property to express this.

Signed-off-by: Lorenz Brun <lorenz@brun.one>
[Tidy up code, restrict changes to 5.15]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
2023-01-24 21:55:44 +01:00
Sander Vanheule
d84dc5d4d7 realtek: rtl931x: drop CONFIG_NO_EXCEPT_FILL hack
On RTL931x builds, CONFIG_RTL931X was used as a stand-in for
CONFIG_NO_EXCEPT_FILL.  Now that the latter is always selected for
devices in the realtek target, this hack can be removed. Resulting
device images are binary identical.

Signed-off-by: Sander Vanheule <sander@svanheule.net>
2023-01-24 21:35:00 +01:00
Olliver Schinagl
1bf39d91d5 realtek: Refresh kernel config with no_except_fill
Update the config files with the previous commit.

Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
2023-01-24 21:00:19 +01:00
Olliver Schinagl
4db8598e42 realtek: Do not set KERNEL_ENTRY just to avoid NO_EXCEPT_FILL
It seems like we are offsetting the KERNEL_ENTRY to +0x400, which is
also accomplished by the NO_EXCEPT_FILL configuration option.

Since this is the default for MIPS_GENERIC_KERNEL, lets push a little
bit closer to that one by doing the same thing.

Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
2023-01-24 21:00:19 +01:00
Nick Hainke
ac21dff5b6 pistachio: switch to 5.15 by default
It appears that only a few users are using the pistachio SoC. The most
active user of the target has already approved the testing kernel and
so it is very unlikely bugs will be reported in the near future.
Therefore, the target should be directly bumped to 5.15.

Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Nick Hainke <vincent@systemli.org>
2023-01-24 00:30:47 +01:00
Nick Hainke
496d32cb78 pistachio: add 5.15 testing kernel
Manually refreshed:
- 903-MIPS-DTS-img-marduk-Add-NXP-SC16IS752IPW.patch
- 905-MIPS-DTS-img-marduk-Add-led-aliases.patch (led node was renamed to led-1)

Automatically refreshed:
- 109-MIPS-DTS-img-marduk-switch-mmc-to-1-bit-mode.patch
- 401-mtd-nor-support-mtd-name-from-device-tree.patch
- 901-MIPS-DTS-img-marduk-Add-SPI-NAND-flash.patch
- 902-MIPS-DTS-img-marduk-Add-Cascoda-CA8210-6LoWPAN.patch
- 904-MIPS-DTS-img-marduk-Add-partition-name.patch

Enable testing kernel.

Co-Developed-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Nick Hainke <vincent@systemli.org>
2023-01-24 00:30:47 +01:00
Nick Hainke
94059ce864 pistachio: 5:15: copy config and patch from 5.10
Copy config and patch from kernel 5.10 to kernel 5.15.

Signed-off-by: Nick Hainke <vincent@systemli.org>
[Updated the copy]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2023-01-24 00:30:19 +01:00
Robert Marko
e3082dc555
generic: backport fix for #nvmem-cell-cells false warning
Recent backport of NVMEM layout support as well as acommpanying OF changes
introduced a false #nvmem-cell-cells warning as #nvmem-cell-cells are
fully optional.

So, backport an upstream fix for this.

Fixes: 11759a5bf3 ("kernel: backport of changes & helpers")
Signed-off-by: Robert Marko <robimarko@gmail.com>
2023-01-23 19:08:01 +01:00
Nikolay Martynov
62dbcb8305 ramips: Fix root volume for tplink-er605-v2
This device has two sets of volumes: main ones (`kernel`, `rootfs`, etc) and
'backup' (`kernel.b`, `rootfs.b`, etc). Bootloader tries to determine which set of
volumes to use by looking at contens of `extra-para` and `extra-para.b` volumes.
These volumes contain JSON that looks like this:

```
{
	"dbootFlag": "1",
	"integerFlag": "1",
	"fwFlag": "GOOD",
	"score":1
}
```

It looks like the bootloader looks for `"fwFlag": "GOOD"` (as opposed to `BAD`)
then it compares `score` field - whichever 'good' volume has bigger score wins.
This determines which set of volumes to use to boot.

So for example if `extra-para` is good and has bigger score then `kernel`,
`rootfs`, etc volumes are used. This means bootloader needs to explain to the
kernel which volume to use for the rootfs. After looking at bootloader code with
disassembler I think it contains a bug. Relevant part of code looks something
like this:

```
  if (image_id == 0) {
    rootfs_volume_id = 8;
    rootfs_volume_name = "rootfs";
  }
  else {
    rootfs_volume_id = 0xf;
    rootfs_volume_name = "rootfs.b";
  }
  sprintf(
    &buffer,
    0x800,
    "console=ttyS0,115200 noinitrd ubi.mtd=3,2048 ubi.block=0,%s
    root=/dev/ubiblock0_%d DKMGT_IMAGE_ID=%d DKMGT_IMAGE_TYPE=ubi",
    rootfs_volume_name,
    rootfs_volume_id,
    image_id
    );
```

Where `image_id == 0` if 'normal' (not '*.b' set of volumes is used).
However from device dumps we know that from the factory `rootfs.b` has id 8 and
`rootfs` has id 15.

So from above we can see that ids and names of rootfs volumes do not match. More
over - they are hardcoded in the bootloader.

Both things are problematic for OpwnWRT which completely removes volumes on
update meaning that volume ids may actually change.

So instead of relying on bootloader to provide the kernel with root device this
patch forces kernel to determine root automatically - and it defaults to
`rootfs` volume which is correct for our purposes.

Overall this makes image boot fine from flash after sysupgrade from inirams.
assuming `extra-para*` volumes make bootloader use non-'*.b' set of volumes.

Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
2023-01-22 14:37:47 +01:00
Alexey Smirnov
f86658e269 omap: refresh config
Refresh target config by running:
make kernel_nconfig CONFIG_TARGET=target

Signed-off-by: Alexey Smirnov <s.alexey@gmail.com>
2023-01-22 02:08:28 +01:00
Alexey Smirnov
c2f0419a12 omap: enable ARM Accelerated Cryptographic Algorithms
This selects cryptographic algorithms implemented
using ARM specific CPU features.

Signed-off-by: Alexey Smirnov <s.alexey@gmail.com>
2023-01-22 02:08:28 +01:00
Alexey Smirnov
8a3a4c84d7 omap: enable cpuidle driver
This enables generic cpuidle driver for ARM.

Signed-off-by: Alexey Smirnov <s.alexey@gmail.com>
2023-01-22 02:08:28 +01:00
John Audia
6a3816efb7 kernel: bump 5.15 to 5.15.89
Removed upstreamed:
  ipq806x/patches-5.15/007-v6.3-ASoC-qcom-lpass-cpu-Fix-fallback-SD-line-index-handl.patch[1]

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.89&id=d4fa65960a9d0cb87a1102d47145675ceed7a4e6

All other patches automatically rebased.

Build system: x86_64
Build-tested: bcm2711/RPi4B, filogic/xiaomi_redmi-router-ax6000-ubootmod
Run-tested: bcm2711/RPi4B, filogic/xiaomi_redmi-router-ax6000-ubootmod

Signed-off-by: John Audia <therealgraysky@proton.me>
2023-01-22 01:41:10 +01:00
INAGAKI Hiroshi
614bba0958 realtek: use irq_force_affinity on otto timer instead
After commit e0d2c59ee995 ("genirq: Always limit the affinity to online
CPUs", 5.10) on Linux, the cpumask passed to irq_set_affinity of irqchip
driver is limited to online CPUs. When irq_do_set_affinity called from
otto timer driver with only one secondary CPU, that CPU is not marked as
online yet, filtered out by cpu_online_mask and fall to error path.
Then, fail to set affinity for that CPU and it leads to instability of
timer on secondary CPU(s).

At least, RTL839x system will be affected.

log:

[   37.560020] rcu: INFO: rcu_sched detected stalls on CPUs/tasks:
[   37.638025] rcu:     1-...!: (0 ticks this GP) idle=6ac/0/0x0 softirq=0/0 fqs=1  (false positive?)
[   37.752683]  (detected by 0, t=6002 jiffies, g=-1179, q=26293)
[   37.829510] Sending NMI from CPU 0 to CPUs 1:
[   37.886857] NMI backtrace for cpu 1 skipped: idling at r4k_wait_irqoff+0x1c/0x24
[   37.984801] rcu: rcu_sched kthread timer wakeup didn't happen for 5999 jiffies! g-1179 f0x0 RCU_GP_WAIT_FQS(5) ->state=0x402
[   38.132743] rcu:     Possible timer handling issue on cpu=1 timer-softirq=0
[   38.221033] rcu: rcu_sched kthread starved for 6000 jiffies! g-1179 f0x0 RCU_GP_WAIT_FQS(5) ->state=0x402 ->cpu=1
[   38.356336] rcu:     Unless rcu_sched kthread gets sufficient CPU time, OOM is now expected behavior.
[   38.474440] rcu: RCU grace-period kthread stack dump:
...

Replace to irq_force_affinity from irq_set_affinity and ignore
cpu_online_mask to fix the issue.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Tested-by: Olliver Schinagl <oliver@schinagl.nl>
2023-01-21 19:58:24 +01:00
Chuanhong Guo
f183ce35b8
kernel: mtk-bmt: fix usage of _oob_read
_oob_read returns number of bitflips on success while
bbt_nand_read should return 0.

Fixes: 2d49e49b18 ("mediatek: bmt: use generic mtd api")
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2023-01-21 10:54:23 +08:00
Brian Norris
ef649b0b14
ipq806x: Initial TP-Link and ASUS OnHub support
TP-Link and ASUS OnHub devices are very similar, sharing many of the
same characteristics and much of their Device Tree. They both run a
version of ChromeOS for their factory firmware, and so installation
instructions look very similar to Google Wifi [1].

Things I've tested, and are working:

 * Ethernet
 * WiFi (2.4 and 5 GHz)
 * LEDs
 * USB
 * eMMC
 * Serial console (if you wire it up yourself)
 * 2x CPU
 * Speaker

== Installation instructions summary ==

1. Flash *-factory.bin to a USB drive (e.g., with `dd`)
2. Insert USB drive, to boot OpenWrt from USB
3. Copy the same *-factory.bin over to device, and flash it to eMMC to
   make OpenWrt permanent

== Developer mode, booting from USB (Step 2) ==

To enter Developer Mode and boot OpenWrt from a USB stick:

1. Unplug power
2. Gain access to the "developer switch" through the bottom of the
   device
3. Hold down the "reset switch" (near the USB port / power plug)
4. Plug power back in
5. The LED on the device should turn white, then blink orange, then
   red. Release the reset switch.
6. Insert USB drive with OpenWrt factory.bin
7. Press the hidden developer switch under the device to boot to USB;
   you should see some activity lights (if you have any) on your USB
   drive
8. Depending on your configuration, the router's LED(s) should come on.
   You're now running OpenWrt off a USB stick.

These instructions are derived from:

https://www.exploitee.rs/index.php/Rooting_The_Google_OnHub#Enabling_%22Developer_Mode%22_on_the_OnHub
https://www.exploitee.rs/index.php/Asus_OnHub#Enabling_%22Developer_Mode%22_on_the_OnHub

~~Finding the developer switch:~~ for TP-Link, the developer switch is
on the bottom of the device, underneath some of the rubber padding and a
screw. For ASUS, remove the entire base, via 4 screws under the rubber
feet. See the Exploitee instructions for more info and photos.

== Making OpenWrt permanent (on eMMC) (Step 3) ==

Once you're running OpenWrt via USB:

1. Connect Ethernet to the LAN port; router's LAN address should be at
   192.168.1.1
2. Connect another system to the router's LAN, and copy the factory.bin
   image over, via SCP and SSH:

     scp -O openwrt-ipq806x-chromium-tplink_onhub-squashfs-factory.bin root@192.168.1.1:
     ssh root@192.168.1.1 -C "dd if=/dev/zero bs=512 seek=7552991 of=/dev/mmcblk0 count=33 && \
     dd if=/root/openwrt-ipq806x-chromium-tplink_onhub-squashfs-factory.bin of=/dev/mmcblk0"
3. Reboot and remove the USB drive.

== Developer mode beep ==

Note that every time you boot the OnHub in developer mode, the device
will play a loud "beep" after a few seconds. This is described in the
Chromium docs [2], and is intended to make it clear that the device is
not running Google software. It is nontrivial to completely disable this
beep, although it's possible to "acknowledge" developer mode (and skip
the beep) by using a USB keyboard to press CTRL+D every time you boot.

[1] https://openwrt.org/toh/google/wifi
[2] https://chromium.googlesource.com/chromiumos/docs/+/HEAD/developer_mode.md

Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2023-01-21 01:02:25 +01:00
Brian Norris
69d1b289b0
ipq806x: Add kmod-sound-soc-ipq8064-storm
For IPQ8064 systems based off the "Google Storm" reference platform,
such as the TP-Link OnHub.

Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2023-01-21 01:02:25 +01:00
Brian Norris
c20915e841
ipq806x: ASoC: qcom: lpass-cpu: Fix fallback SD line index handling
This fixes device tree registration for 'qcom,lpass-cpu' as used by
qcom-ipq8064 SoCs, and allows speaker audio to function.

This patch has been submitted (and merged, for -next; likely v6.3)
upstream.

Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2023-01-21 01:02:24 +01:00
Brian Norris
108ed0e1c7
ipq806x: config-5.15: Normalize
Refresh target config with `make kernel_menuconfig`, then save the
result. This drops missing symbols or otherwise accounts for defaults.
It should not change any functionality.

Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2023-01-21 01:02:24 +01:00
Brian Norris
84ee3436a4
ipq806x: Point to externally compiled dtbs in recipes
Similar to commit 4d8b42d8a7 ("ipq40xx: point to externally compiled
dtbs in recipes").

Currently, we patch our DTS files into the kernel source tree, so the
kernel build process will produce DTBs for us. The kernel-to-DTS
dependency can cause buildroot to perform excessive rebuilds of the
kernel though, which slows down device development iteration.

Buildroot also compiles DTBs on its own, to
$(KDIR)/image-$(DEVICE_DTS).dtb. With small adjustments, we can leverage
this, and stop patching DTS files into the kernel Makefile at the same
time.

Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2023-01-21 01:02:24 +01:00
Josef Schlehofer
6475d030b9 mvebu: cortexa9: use renamed U-boot binaries
Due to upstream change in U-boot the binaries were renamed [1].

[1] 87ac4b4b4c

Fixes: 2f83369e3e ("uboot-mvebu: update to version 2023.01")
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
2023-01-20 21:10:37 +01:00
André Valentin
5dee596501
ipq807x: Add ZyXEL NBG7815
ZyXEL NBG7815 is a premium 802.11ax "tri"-band router/AP.
Specifications:
* CPU: Qualcomm IPQ8072A Quad core Cortex-A53 2.2GHz
* RAM: 1 GB 2x Nanya NT5CC256M16ER-EK
* Storage:
        * 8MB serial flash Winbond W25Q64DW
        * 4GB eMMC flash Kingston EMMC04G-M627
* Ethernet:
        * 4x1G RJ45 ports (QCA8074A) with 1x status LED per port
        * 1x2.5G RJ45 port (QCA8081) with 1x status LED
        * 1x10G RJ45 port (AQR113C) with 1x status LED
* Switch: Qualcomm Atheros QCA8075
* WLAN:
        * 2.4GHz: Qualcomm QCN5024 4x4@40MHz 802.11b/g/n/ax 1147 Mbps PHY rate
        * 2x 5GHz: Qualcomm QCN5054 4x4 802.11a/b/g/n/ac/ax 2402 PHY rate
* Bluetooth CSR8811 using HSUART, currently unsupported
* USB: 1x USB3.0 Type-A port
* LED-s currently not supported:
        * White
        * Dark Blu
        * Amber
        * Purple
        * Purple and dark blue
        * Red
* Buttons:
        * 1x Soft reset
* Power: 12V DC Jack

Installation instructions:
* Disconnect WAN
* Reset device to factory defaults by pushing reset button 15 sec,
  LEDs should lit orange color.
* After 5-10 minutes, when the LEDs turn constant dark blue,
  put your LAN cable and connect at address 192.168.123.1 by telnet on port 23
* Login with
  NBG7815 login: root
  password: nbg7815@2019
* cd /tmp/ApplicationData
* wget -O openwrt-ipq807x-generic-zyxel_nbg7815-squashfs-sysupgrade.bin http://...
* wget https://github.com/itorK/nbg7815_tools/blob/main/flash_to_openwrt.sh
* run flash_to_openwrt.sh
If you can't use wget, you can transfer the files via nc.
See https://openwrt.org/inbox/toh/zyxel/nbg7815_armor_g5 for installation details.

Bluetooth usage:
* you need at least package bluez-utils, recommended bluez-daemon
* run following commands to enable and start
  hciattach  /dev/ttyMSM1 bcsp
  hciconfig hci0 up

Many thanks to itorK for his work on this device:
https://github.com/itorK/openwrt/tree/nbg7815

Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: André Valentin <avalentin@marcant.net>
2023-01-19 13:26:15 +01:00
André Valentin
952c738c0f
ipq807x: add nvmem uboot-env support
Enabling kernel symbol CONFIG_NVMEM_U_BOOT_ENV allows to use u-boot
environement variable ethaddr with nvmen. That way it is possible to assign
the MAC address to the ethernet device driver.

Example of usage in dts:
....
	partition@600000 {
			compatible = "u-boot,env";
			label = "0:appsblenv";
			reg = <0x600000 0x10000>;

			macaddr_lan: ethaddr {
			};
	};
....
&dp5 {
	status = "okay";
	phy-handle = <&qca8081>;
	label = "wan";
	nvmem-cells = <&macaddr_lan>;
	nvmem-cell-names = "mac-address-ascii";
	mac-address-increment = <1>;
};

This is needed for Zyxel NBG7815.

Signed-off-by: André Valentin <avalentin@marcant.net>
2023-01-19 13:26:15 +01:00
James Andrewartha
7c04e80f87 ipq40xx: convert Extreme AP3915i to DSA
Convert and re-enabled Extreme AP3915i to DSA.

Signed-off-by: James Andrewartha <trs80@ucc.asn.au>
2023-01-17 23:45:44 +01:00
Martin Schiller
539b52068a ipq40xx: add DSL support for FritzBox 7530
Set up MAC, LED, settings and default packages for DSL usage, similar
to the lantiq target.

Due to licensing uncertainty, we do not include the firmware files for the
DSL drivers. To have a working DSL setup, follow the instructions below.

Download the firmware files locally:

  mkdir -p files/lib/firmware/09a9
  wget -P files/lib/firmware/09a9 https://gitlab.com/prpl-foundation/intel/vrx518_aca_fw/-/raw/ugw-8.5.2/platform/xrx500/aca_fw.bin
  wget -P files/lib/firmware https://gitlab.com/prpl-foundation/intel/vrx518_ppe_fw/-/raw/ugw_8.5.2.10/platform/xrx500/ppe_fw.bin
  wget -P files/lib/firmware https://gitlab.com/prpl-foundation/intel/dsl_vr11_firmware_xdsl/-/raw/ugw-8.5.2/xcpe_8D1507_8D0901.bin
  ln -s xcpe_8D1507_8D0901.bin files/lib/firmware/vdsl.bin

For people building their own images:

Run the above commands in the root of your local OpenWrt clone,
and the firmware files will be part of the resulting images.

For people downloading images:

Copy the firmware files onto the router once it's booted up:
  scp -O -r files/lib/firmware root@fritz:/lib
Reboot the device afterwards.

Signed-off-by: Martin Schiller <ms.3headeddevs@gmail.com>
[cleaned up]
Signed-off-by: Andre Heider <a.heider@gmail.com>
[set up LED]
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Signed-off-by: Andre Heider <a.heider@gmail.com>
2023-01-16 23:41:41 +00:00
Martin Schiller
bc205a34a4 ipq40xx: fritzbox-7530.dts: increase dma coherent pool size
This is needed by the mei driver to be able to download the firmware.

Signed-off-by: Martin Schiller <ms.3headeddevs@gmail.com>
Signed-off-by: Andre Heider <a.heider@gmail.com>
2023-01-16 23:41:41 +00:00
Martin Schiller
cfd42a0098 ipq40xx: add Intel/Lantiq ATM hacks
Similar to the lantiq platform, these are required for DSL support.

Signed-off-by: Martin Schiller <ms.3headeddevs@gmail.com>
[switch to kernel 5.10 and 5.15]
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
[update patches based on UGW 8.5.2.10, remove 5.10 support]
Signed-off-by: Andre Heider <a.heider@gmail.com>
2023-01-16 23:41:41 +00:00
Daniel Golle
ab3c9ccb61
mediatek: filogic: fix sysupgrade on MMC on the BPi-R3
A previous attempt to simplify things went wrong and now sysupgrade
is broken on this device. Fix that.

Fixes: de94587e70 ("mediatek: filogic: don't rely on image preset in flash or sysupgrade")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-01-16 22:04:55 +00:00
Daniel Golle
86a2dae29a
mediatek: mt7622: fix sysupgrade on MMC on BPi-R64
A previous attempt to simplify things went wrong and now sysupgrade
is broken on this device. Fix that.

Fixes: d640cbac0e ("mediatek: mt7622: don't rely on existing image for sysupgrade")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-01-16 22:04:44 +00:00
Daniel Golle
83c0942ff7
kernel: fix kernel panic in mtk_ppe
The patch that adds support for hw flow-offloading counters on newer
MediaTek SoCs tries to prints acct->packets and acct->bytes in debugfs,
without checking that acct isn't null. This causes a kernel panic when
trying to read /sys/kernel/debug/ppe0/entries on older MediaTek SoCs.
Fix this by adding a check for acct.

Fixes: openwrt#11756
Fixes: 9721a42a27 ("kernel: support hw flow-offloading counters on newer MediaTek SoCs")
Reported-by: Stijn Tintel <stijn@linux-ipv6.be>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-01-16 22:04:35 +00:00
Nick Hainke
1cefb14230
archs38: switch to 5.15 by default
It appears that only a few users are using the archs38 SoC. The most
active user of the target has already approved the testing kernel and
so it is very unlikely bugs will be reported in the near future.
Therefore, the target should be directly bumped to 5.15.

Signed-off-by: Nick Hainke <vincent@systemli.org>
2023-01-16 20:48:01 +01:00
Dirk Buchwalder
26c095cb4d ipq807x: add Dynalink DL-WRX36
Dynalink DL-WRX36 is a AX WIFI router with 4 1G and 1 2.5G ports.

Specifications:

    •     CPU: Qualcomm IPQ8072A Quad core Cortex-A53 2.2GHz
    •     RAM: 1024MB of DDR3
    •     Storage: 256MB Nand
    •     Ethernet: 4x 1G RJ45 ports (QCA8075) + 1 2.5G Port (QCA8081)
    •     WLAN:
          2.4GHz: Qualcomm QCN5024 2x2 802.11b/g/n/ax 1174 Mbps PHY rate
          5GHz: Qualcomm QCN5054 4x4 802.11a/b/g/n/ac/ax 2402 PHY rate
    •     1x USB 3.0

    •     1 gpio-controlled dual color led (blue/red)

            • Buttons: 1x soft reset / 1x WPS
            • Power: 12V DC jack

        A poulated serial header is onboard (J1004)
        the connector size is a 4-pin 2.0 mm JST PH.
        RX/TX is working, u-boot bootwait is active, secure boot is enabled.

        Notes:
	- Serial is completely deactivated in the stock firmware image.
	- This commit adds only single partition support, that means
	  sysupgrade is upgrading the current rootfs partition.
	- Installation can be done by serial connection or
	  SSH access on OEM firmware

	Installation Instructions:

	Most part of the installation is performed from an initramfs image
	running OpenWrt, and there are two options to boot it.

	Boot initramfs option 1: Using serial connection (3.3V)
	1. Stop auto boot to get to U-boot shell
	2. Transfer initramfs image to device
	   (openwrt-ipq807x-generic-dynalink_dl-wrx36-initramfs-uImage.itb)
	   Tested using TFTP and a FAT-formatted USB flash drive.
	3. Boot the initramfs image
	   # bootm

	Boot initramfs option 2: From SSH access on OEM firmware
	1. Copy the initramfs image to a FAT-formatted flash drive
	   (tested on single-partition drive) and connect it to device USB port.
	2. Change boot command so it loads the initramfs image on next boot
	   Fallback to OEM firmware is provided.
	   # fw_setenv bootcmd 'usb start && fatload usb 0:1 0x44000000 openwrt-ipq807x-generic-dynalink_dl-wrx36-initramfs-uImage.itb && bootm 0x44000000; bootipq'
	3. Reboot the device to boot the initramfs
	   # reboot

	Install OpenWrt from initramfs image:
	1. Use SCP (or other way) to transfer OpenWrt factory image
	2. Connect to device using SSH (on a LAN port)
	3. Check MTD partition table.
	   rootfs and rootfs_1 should be mtd18 and mtd20
	   depending on current OEM slot.
	   # cat /proc/mtd
	4. Do a ubiformat to both rootfs partitions:
	   # ubiformat /dev/mtd18 -y -f /path_to/factory_image
	   # ubiformat /dev/mtd20 -y -f /path_to/factory_image
	5. Set U-boot env variable: mtdids
	   # fw_setenv mtdids 'nand0=nand0'
	6. Get offset of mtd18 to determine current OEM slot
	   - If current OEM slot is 1, offset is 16777216  (0x1000000)
	   - If current OEM slot is 2, offset is 127926272 (0x7a00000)
	   # cat /sys/class/mtd/mtd18/offset
	7. Set U-boot env variable: mtdparts
	   If current OEM slot is 1, run:
	   # fw_setenv mtdparts 'mtdparts=nand0:0x6100000@0x1000000(fs),0x6100000@0x7a00000(fs_1)'
	   If current OEM slot is 2, run:
	   # fw_setenv mtdparts 'mtdparts=nand0:0x6100000@0x7a00000(fs),0x6100000@0x1000000(fs_1)'
	8. Set U-boot env variable: bootcmd
	   # fw_setenv bootcmd 'setenv bootargs console=ttyMSM0,115200n8 ubi.mtd=rootfs rootfstype=squashfs rootwait; ubi part fs; ubi read 0x44000000 kernel; bootm 0x44000000#config@rt5010w-d350-rev0'
	9. Reboot the device
	   # reboot

        Note: this PR adds only single partition support, that means sysupgrade is
              upgrading the current rootfs partition

Signed-off-by: Dirk Buchwalder <buchwalder@posteo.de>
2023-01-16 12:42:23 +01:00
Matthew Hagan
6e03304c76 ipq807x: add Edgecore EAP102
The Edgecore EAP102 is a wall/ceiling mountable AP. The AP can be
powered by either PoE or AC adapter.

Device info:
 - IPQ8071-A SoC
 - 1GiB RAM
 - 256MiB NAND flash
 - 32MiB SPI NOR
 - 2 Ethernet ports
 - 1 Console port
 - 2GHz/5GHz AX WLAN
 - 2 USB 2.0 ports

Install instructions:

Prerequistes - TFTP server, preferrably within 192.168.1.0/24
	       Console cable plugged in (115200 8N1 no flow control)

1. Power on device and interrupt u-boot to obtain u-boot CLI

2. set serverip to IP address of the TFTP server:

	`setenv serverip 192.168.1.250`

3. Download image from TFTP server:

	`tftpboot 0x44000000 openwrt-ipq807x-generic-edgecore_eap102-squashfs-nand-factory.ubi`

4. Flash ubi image to both partitions and reset:

	`sf probe
	 imxtract 0x44000000 ubi
	 nand device 0
	 nand erase 0x0 0x3400000
	 nand erase 0x3c00000 0x3400000
	 nand write $fileaddr 0x0 $filesize
	 nand write $fileaddr 0x3c00000 $filesize
	 reset`

Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
2023-01-16 12:42:23 +01:00
Robert Marko
2ddb2057cd ipq807x: Add Xiaomi AX9000
Xiaomi AX9000 is a premium 802.11ax "tri"-band router/AP.
Specifications:
* CPU: Qualcomm IPQ8072A Quad core Cortex-A53 2.2GHz
* RAM: 1024MB of DDR3
* Storage: 256MB of parallel NAND
* Ethernet:
	* 4x1G RJ45 ports (QCA8075) with 1x status LED per port
	* 1x2.5G RJ45 port (QCA8081) with 1x status LED
* WLAN:
	* PCI based Qualcomm QCA9889 1x1 802.11ac Wawe 2 for IoT
	* 2.4GHz: Qualcomm QCN5024 4x4@40MHz 802.11b/g/n/ax 1147 Mbps PHY rate
	* 5.8GHz: Qualcomm QCN5054 4x4@80MHz or 2x2@160MHz 802.11a/b/g/n/ac/ax 2402Mbps PHY rate
	* 5GHz: PCI based Qualcomm QCN9024 4x4@160MHz 802.11a/b/g/n/ac/ax 4804Mbps PHY rate
* USB: 1x USB3.0 Type-A port
* LED-s:
	* System (Blue and Yellow)
	* Network (Blue and Yellow)
	* RGB light bar on top in X shape
* Buttons:
	* 1x Power switch
	* 1x Soft reset
	* 1x Mesh button
* Power: 12V DC Jack

Installation instructions:

Obtaining SSH access is mandatory
https://openwrt.org/inbox/toh/xiaomi/ax9000#obtain_ssh_access

Installation is done by the ubiformat method, through SSH:
1. Open an SSH shell to the router
2. Copy the file openwrt-ipq807x-generic-xiaomi_ax9000-initramfs-factory.ubi to the /tmp directory
3. Check which rootfs partition is your router booted in (0 = rootfs | 1 = rootfs_1):
nvram get flag_boot_rootfs

4. Find the rootfs and rootfs_1 mtd indexes respectively:
cat /proc/mtd
Please confirm if mtd21 and mtd22 are the correct indexes from above!

5. Use the command ubiformat to flash the opposite mtd with UBI image:

If nvram get flag_boot_rootfs returned 0:
ubiformat /dev/mtd22 -y -f /tmp/openwrt-ipq807x-generic-xiaomi_ax9000-initramfs-factory.ubi && nvram set flag_boot_rootfs=1 && nvram set flag_last_success=1 && nvram commit

otherwise:
ubiformat /dev/mtd21 -y -f /tmp/openwrt-ipq807x-generic-xiaomi_ax9000-initramfs-factory.ubi && nvram set flag_boot_rootfs=0 && nvram set flag_last_success=0 && nvram commit

6. Reboot the device by:
reboot

Previous commands flashed an ubinized OpenWrt initramfs that will serve as the intermediate step
since OpenWrt uses unified rootfs in order to fully utilize NAND and provide enough space for packages.
Continue in order to pernamently flash OpenWrt:

7. SSH into OpenWrt from one of the LAN ports
8. Copy the file openwrt-ipq807x-generic-xiaomi_ax9000-squashfs-sysupgrade.bin to the /tmp directory
9. Sysupgrade the device:
sysupgrade -n /tmp/openwrt-ipq807x-generic-xiaomi_ax9000-squashfs-sysupgrade.bin

Device will reboot with OpenWrt, and then sysupgrade can be used to upgrade the device when desired.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2023-01-16 12:42:23 +01:00
Dirk Buchwalder
bd17683261 ipq807x: add QNAP 301w
QNAP 301w is a AX WIFI router with 4 1G and 2 10G ports.

Specifications:

    •     CPU: Qualcomm IPQ8072A Quad core Cortex-A53 2.2GHz
    •     RAM: 1024MB of DDR3
    •     Storage: 4GB eMMC (contains kernel and rootfs) / 8MB NOR
          (contains art and u-boot-env)
    •     Ethernet: 4x 1G RJ45 ports + 2 10G ports (Aquantia AQR113C)
    •     WLAN:
          2.4GHz: Qualcomm QCN5024 4x4 (40 MHz) 802.11b/g/n/ax 1174 Mbps PHY rate
          5GHz: Qualcomm QCN5054 4x4 (80 MHz) or 2x2 (160 MHz) 802.11a/b/g/n/ac/ax 2402 PHY rate

    •     LEDs:
          7 x GPIO-controlled dual color LEDs + 2 GPIO-controlled single color LEDs

            • Buttons: 1x soft reset / 1x WPS
            • Power: 12V DC jack

        A poulated serial header is onboard.
        RX/TX is working, bootwait is active, secure boot is not enabled.

        SSH can be activated in the stock firmware, hold WPS button til the second beep
	(yes the router has a buzzer)
        SSH is available on port 22200, login with user admin and
	password "mac address of the router".

        Installation Instructions:

            • obtain serial access (https://openwrt.org/inbox/toh/qnap/301w#serial)
            • stop auto boot
            • setenv serverip 192.168.10.1
            • setenv ipaddr 192.168.10.10
            • tftpboot the initramfs image
              (openwrt-ipq807x-generic-qnap_301w-initramfs-fit-uImage.itb)
            • bootm

            • make sure that current_entry is set to "0":
              "fw_printenv -n current_entry" should be print "0". If not,
	       do "fw_setenv current_entry 0"
            • copy openwrt-ipq807x-generic-qnap_301w-squashfs-sysupgrade.bin
	          to the device to /tmp folder
            • sysupgrade -n /tmp/openwrt-ipq807x-generic-qnap_301w-squashfs-sysupgrade.bin
              this flashes openwrt to the first kernel and rootfs partition (mmcblk0p1 / mmcblk0p4)
            • reboot

        Note: this leaves the second kernel / rootfs parition untouched. So if you want
              to go back to stock, stop u-boot autoboot, "setenv current_entry 1" ,
	       "saveenv", "bootipq".
              Stock firmware should start from the second partition.
	      Then do a firmwareupgrade in the stock gui, that should overwrite the openwrt
	      in the first partitions

        Make 10G Aquantia phy's work:
              The aquantia phy's need a firmware to work. This can either be loaded
	      in linux with a userspace tool or in u-boot.

              I was not successfull to load the firmware in linux (aq-fw-download) but luckily there is
	      aq_load_fw available in u-boot. But first the right firmware needs to write
	      to the 0:ETHPHYFW mtd partition (it is empty on my device)

              Grab the ethphy firmware image from:
	      https://github.com/kirdesde/nbg7815_gpl/blob/master/target/linux/ipq/ipq807x_64/prebuilt_images/AQR_ethphyfw.mbn
	      and scp that to openwrt.

              Check the 0:ETHPHYFW partition number:
              cat /proc/mtd|grep "0:ETHPHYFW", should be mtd10.

              Backup the 0:ETHPHYFW partition:
              dd if=/dev/mtd10 of=/tmp/ethphyfw.backup, scp ethphyfw.backup to a save place.

              Write the new firmware image to the 0:ETHPHYFW partition:
              "mtd erase /dev/mtd10", "mtd -n write AQR_ethphyfw.mbn /dev/mtd10".

              Reboot to u-boot.

              Check if aq_load_fw is working:

              "aq_load_fw 0", that checks the firmware and if successfull,
	      loads iram and dram to one of the aquantia phy's.

              If that worked, add the aq_load_fw to the bootcmd:
              setenv bootcmd "aq_load_fw 0 && aq_load_fw 8 && bootipq"

              "saveenv"

              "reset"

              Board reboots and the firmware load to both phy's should start and
	      then openwrt boots.

              Check if the 10G ports work.

              Note: lan port labeled "10G-2" is configured as WAN port as per default.
	      All other port are in the br-lan. This can be changed in the network config.

Signed-off-by: Dirk Buchwalder <buchwalder@posteo.de>
2023-01-16 12:42:23 +01:00
Dirk Buchwalder
a36fc589fe ipq807x: add Edimax CAX1800
Edimax CAX1800 is a 802.11 ax dual-band AP
with PoE. AP can be ceiling or wall mount.

Specifications:

    •     CPU: Qualcomm IPQ8070A Quad core Cortex-A53 1.4GHz
    •     RAM: 512MB of DDR3
    •     Storage: 128MB NAND (contains rootfs) / 8MB NOR (contains art and uboot-env)
    •     Ethernet: 1x 1G RJ45 port (QCA8072) PoE
    •     WLAN:
          2.4GHz: Qualcomm QCN5024 2x2 802.11b/g/n/ax 574 Mbps PHY rate
          5GHz: Qualcomm QCN5054 2x2 802.11a/b/g/n/ac/ax 1201 PHY rate

    •     LEDs:
          3 x GPIO-controlled System-LEDs
          (form one virtual RGB System-LED)
            black_small_square  Buttons: 1x soft reset
            black_small_square  Power: 12V DC jack or PoE (802.3af )

        An unpopulated serial header is onboard.
        RX/TX is working, bootwait is active, secure boot is not enabled.

        SSH can be activated in the stock firmware, but it drops only
        to a limited shell .

        Installation Instructions:

            black_small_square obtain serial access
            black_small_square stop auto boot

            black_small_square tftpboot the initramfs image (serverip is set to 192.168.99.8 in uboot)
            black_small_square bootm

            black_small_square copy openwrt-ipq807x-generic-edimax_cax1800-squashfs-nand-factory.ubi
	      to the device
            black_small_square write the image to the NAND:
            black_small_square cat /proc/mtd and look for rootfs partition (should be mtd0)
            black_small_square ubiformat /dev/mtd0 -f -y  openwrt-ipq807x-generic-edimax_cax1800-squashfs-
              nand-factory.ubi
            black_small_square reboot

	Note: Device is not using dual partitioning (NAND contains other partitions
        with different manufacture data etc.)
	Draytek VigorAP 960C and Lancom LW-600 both look similar, but I haven't checked them.

Signed-off-by: Dirk Buchwalder <buchwalder@posteo.de>
2023-01-16 12:42:23 +01:00
Zhijun You
8253cb2de5 ipq807x: add Redmi AX6
Redmi AX6 is a budget 802.11ax dual-band router/AP

Specifications:
* CPU: Qualcomm IPQ8071A Quad core Cortex-A53 1.4GHz
* RAM: 512MB of DDR3
* Storage: 128MB NAND
* Ethernet: 4x1G RJ45 ports (QCA8075)
* WLAN:
	* 2.4GHz: Qualcomm QCN5024 2x2 802.11b/g/n/ax 574 Mbps PHY rate
	* 5GHz: Qualcomm QCN5054 4x4@80MHz or 2x2@160MHz 802.11a/b/g/n/ac/ax 2402 PHY rate
* LEDs:
	* System (Blue/Yellow)
	* Network (Blue/Yellow)
*Buttons: 1x soft reset
*Power: 12V DC jack

Installation instructions:

Obtaining SSH access is mandatory
https://openwrt.org/inbox/toh/xiaomi/xiaomi_redmi_ax6_ax3000#ssh_access

Installation is done by the ubiformat method, through SSH:
1. Open an SSH shell to the router
2. Copy the file openwrt-ipq807x-generic-redmi_ax6-initramfs-factory.ubi to the /tmp directory
3. Check which rootfs partition is your router booted in (0 = rootfs | 1 = rootfs_1):
nvram get flag_boot_rootfs

4. Find the rootfs and rootfs_1 mtd indexes respectively:
cat /proc/mtd
Please confirm if mtd12 and mtd13 are the correct indexes from above!

5. Use the command ubiformat to flash the opposite mtd with UBI image:

If nvram get flag_boot_rootfs returned 0:
ubiformat /dev/mtd13 -y -f /tmp/openwrt-ipq807x-generic-redmi_ax6-initramfs-factory.ubi && nvram set flag_boot_rootfs=1 && nvram set flag_last_success=1 && nvram commit

otherwise:
ubiformat /dev/mtd12 -y -f /tmp/openwrt-ipq807x-generic-redmi_ax6-initramfs-factory.ubi && nvram set flag_boot_rootfs=0 && nvram set flag_last_success=0 && nvram commit

6. Reboot the device by:
reboot

Previous commands flashed an ubinized OpenWrt initramfs that will serve as the intermediate step
since OpenWrt uses unified rootfs in order to fully utilize NAND and provide enough space for packages.
Continue in order to pernamently flash OpenWrt:

7. SSH into OpenWrt from one of the LAN ports
8. Copy the file openwrt-ipq807x-generic-redmi_ax6-squashfs-sysupgrade.bin to the /tmp directory
9. Sysupgrade the device:
sysupgrade -n /tmp/openwrt-ipq807x-generic-redmi_ax6-squashfs-sysupgrade.bin

Device will reboot with OpenWrt, and then sysupgrade can be used to upgrade the device when desired.

Signed-off-by: Zhijun You <hujy652@gmail.com>
2023-01-16 12:42:23 +01:00
Robert Marko
8364f08164 ipq807x: add Xiaomi AX3600
Xiaomi AX3600 is a budget 802.11ax dual-band router/AP.
Specifications:
* CPU: Qualcomm IPQ8071A Quad core Cortex-A53 1.4GHz
* RAM: 512MB of DDR3
* Storage: 256MB of parallel NAND
* Ethernet: 4x1G RJ45 ports (QCA8075) with 1x status LED per port
* WLAN:
	* PCI based Qualcomm QCA9889 1x1 802.11ac Wawe 2 for IoT
	* 2.4GHz: Qualcomm QCN5024 2x2 802.11b/g/n/ax 574 Mbps PHY rate
	* 5GHz: Qualcomm QCN5054 4x4@80MHz or 2x2@160MHz 802.11a/b/g/n/ac/ax 2402 PHY rate
* LED-s:
	* System (Blue and Yellow)
	* IoT (Blue)
	* Network (Blue and Yellow)
* Buttons: 1x Soft reset
* Power: 12V DC Jack

Installation instructions:

Obtaining SSH access is mandatory
https://openwrt.org/inbox/toh/xiaomi/xiaomi_ax3600#obtain_ssh_access

Installation is done by the ubiformat method, through SSH:
1. Open an SSH shell to the router
2. Copy the file openwrt-ipq807x-generic-xiaomi_ax3600-initramfs-factory.ubi to the /tmp directory
3. Check which rootfs partition is your router booted in (0 = rootfs | 1 = rootfs_1):
nvram get flag_boot_rootfs

4. Find the rootfs and rootfs_1 mtd indexes respectively:
cat /proc/mtd
Please confirm if mtd12 and mtd13 are the correct indexes from above!

5. Use the command ubiformat to flash the opposite mtd with UBI image:

If nvram get flag_boot_rootfs returned 0:
ubiformat /dev/mtd13 -y -f /tmp/openwrt-ipq807x-generic-xiaomi_ax3600-initramfs-factory.ubi -s 2048 -O 2048 && nvram set flag_boot_rootfs=1 && nvram set flag_last_success=1 && nvram commit

otherwise:
ubiformat /dev/mtd12 -y -f /tmp/openwrt-ipq807x-generic-xiaomi_ax3600-initramfs-factory.ubi -s 2048 -O 2048 && nvram set flag_boot_rootfs=0 && nvram set flag_last_success=0 && nvram commit

6. Reboot the device by:
reboot

Previous commands flashed an ubinized OpenWrt initramfs that will serve as the intermediate step
since OpenWrt uses unified rootfs in order to fully utilize NAND and provide enough space for packages.
Continue in order to pernamently flash OpenWrt:

7. SSH into OpenWrt from one of the LAN ports
8. Copy the file openwrt-ipq807x-generic-xiaomi_ax3600-squashfs-sysupgrade.bin to the /tmp directory
9. Sysupgrade the device:
sysupgrade -n /tmp/openwrt-ipq807x-generic-xiaomi_ax3600-squashfs-sysupgrade.bin

Device will reboot with OpenWrt, and then sysupgrade can be used to upgrade the device when desired.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Robert Marko <robimarko@gmail.com>
2023-01-16 12:42:23 +01:00
Robert Marko
bc120521db ipq807x: include kmods for wired networking by default
Include NSS DP and SSDK (Pulled as dependency) by default on ipq807x to
provide wired networking to the target.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2023-01-16 12:42:23 +01:00
Robert Marko
d092dee9ed ipq807x: include ath11k-ahb by default
All of the IPQ807x devices support having 2 radios, so lets include the
required driver as well.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2023-01-16 12:42:23 +01:00
Robert Marko
4359d10b01 kernel: 5.15: add missing kernel configuration options
Found during compilation of ipq807x with ALL_NONSHARED.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2023-01-16 12:42:23 +01:00
Robert Marko
b5f32064ed ipq807x: add Qualcomm Atheros IPQ807x target
Qualcomm Atheros IPQ807x is a modern WiSoC featuring:
* Quad Core ARMv8 Cortex A-53
	* @ 2.2 GHz (IPQ8072A/4A/6A/8A) Codename Hawkeye
	* @ 1.4 GHz (IPQ8070A/1A) Codename Acorn
* Dual Band simultaneaous IEEE 802.11ax
	* 5G: 8x8/80 or 4x4/160MHz (IPQ8074A/8A)
	* 5G: 4x4/80 or 2x2/160MHz (IPQ8071A/2A/6A)
	* 5G: 2x2/80MHz (IPQ8070A)
	* 2G: 4x4/40MHz (IPQ8072A/4A/6A/8A)
	* 2G: 2x2/40MHz (IPQ8070A/1A)
* 1x PSGMII via QCA8072/5 (Max 5x 1GbE ports)
* 2x SGMII/USXGMII (1/2.5/5/10 GbE) on Hawkeye
* 2x SGMII/USXGMII (1/2.5/5 GbE) on Acorn
* DDR3L/4 32/16 bit up to 2400MT/s
* SDIO 3.0/SD card 3.0/eMMC 5.1
* Dual USB 3.0
* One PCIe Gen2.1 and one PCIe Gen3.0 port (Single lane)
* Parallel NAND (ONFI)/LCD
* 6x QUP BLSP SPI/I2C/UART
* I2S, PCM, and TDMA
* HW PWM
* 1.8V configurable GPIO
* Companion PMP8074 PMIC via SPMI (GPIOS, RTC etc)

Note that only v2 SOC models aka the ones ending with A suffix are
supported, v1 models do not comply to the final 802.11ax and have
lower clocks, lack the Gen3 PCIe etc.

SoC itself has two UBI32 cores for the NSS offloading system, however
currently no offloading is supported.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2023-01-16 12:42:23 +01:00
Robert Marko
6c9329e088 generic: 5.15: add MHI SBL callback for ath11k
This adds the MHI SBL callback that ath11k will utilize in order to
support multiple PCI cards or AHB+PCI combo which currently does not
work due to QRTR ID-s conflicting.

This is a prerequisite for the mac80211 patch targeting ath11k as it
uses MHI from kernel.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2023-01-16 12:42:23 +01:00
Robert Marko
c01641bcc7 archs38: mark as source-only
archs38 seems to be pretty much unused, usually only treewide changes or
kernel bumps in order to branch off new stable are done to it.

Considering that target only support some Synopsis HS38 ARC reference
boards and no consumer hardware so mark the target as source-only to stop
using Buildbot resources on building the target and packages for it.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2023-01-16 11:05:34 +01:00
Harm Berntsen
09f313bfd7 ramips: mt7621: Add Arcadyan WE420223-99 support
The Arcadyan WE420223-99 is a WiFi AC simultaneous dual-band access
point distributed as Experia WiFi by KPN in the Netherlands. It features
two ethernet ports and 2 internal antennas.

Specifications
--------------
SOC   : Mediatek MT7621AT
ETH   : Two 1 gigabit ports, built into the SOC
WIFI  : MT7615DN
BUTTON: Reset
BUTTON: WPS
LED   : Power (green+red)
LED   : WiFi (green+blue)
LED   : WPS (green+red)
LED   : Followme (green+red)
Power : 12 VDC, 1A barrel plug

Winbond variant:
RAM   : Winbond W631GG6MB12J, 1GBIT DDR3 SDRAM
Flash : Winbond W25Q256JVFQ, 256Mb SPI
U-Boot: 1.1.3 (Nov 23 2017 - 16:40:17), Ralink 5.0.0.1

Macronix variant:
RAM   : Nanya NT5CC64M16GP-DI, 1GBIT DDR3 SDRAM
Flash : MX25l25635FMI-10G, 256Mb SPI
U-Boot: 1.1.3 (Dec  4 2017 - 11:37:57), Ralink 5.0.0.1

Serial
------
The serial port needs a TTL/RS-232 3V3 level converter! The Serial
setting is 57600-8-N-1. The board has an unpopulated 2.54mm straight pin
header.

The pinout is: VCC (the square), RX, TX, GND.

Installation
------------
See the Wiki page [1] for more details, it comes down to:

1. Open the device, take off the heat sink
2. Connect the SPI flash chip to a flasher, e.g. a Raspberry Pi. Also
   connect the RESET pin for stability (thanks @FPSUsername for reporting)
3. Make a backup in case you want to revert to stock later
4. Flash the squashfs-factory.trx file to offset 0x50000 of the flash
5. Ensure the bootpartition variable is set to 0 in the U-Boot
   environment located at 0x30000

Note that the U-Boot is password protected, this can optionally be
removed. See the forum [2] for more details.

MAC Addresses(stock)
--------------------
+----------+------------------+-------------------+
| use      | address          | example           |
+----------+------------------+-------------------+
| Device   | label            | 00:00:00:11:00:00 |
| Ethernet | + 3              | 00:00:00:11:00:03 |
| 2g       | + 0x020000f00001 | 02:00:00:01:00:01 |
| 5g       | + 1              | 00:00:00:11:00:01 |
+----------+------------------+-------------------+

The label address is stored in ASCII in the board_data partition

Notes
-----
- This device has a dual-boot partition scheme, but OpenWRT will claim
  both partitions for more storage space.

Known issues
------------
- 2g MAC address does not match stock due to missing support for that in
  macaddr_add
- Only the power LED is configured by default

References
----------
[1] https://openwrt.org/inbox/toh/arcadyan/astoria/we420223-99
[2] https://forum.openwrt.org/t/adding-openwrt-support-for-arcadyan-we420223-99-kpn-experia-wifi/132653

Acked-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: Harm Berntsen <git@harmberntsen.nl>
2023-01-15 13:41:02 +01:00
Florian Eckert
1e0604e0d1 kernel/x86: fix typo
Fix typo for KernelPackage w83627hf-wdt.

Signed-off-by: Florian Eckert <fe@dev.tdt.de>
2023-01-15 13:30:09 +01:00
Vincent Tremblay
9e4ede8344 ipq40xx: add support for Linksys WHW03 V2
SOC:             Qualcomm IPQ4019
WiFi 1:          QCA4019 IEEE 802.11b/g/n
WiFi 2:          QCA4019 IEEE 802.11a/n/ac
WiFi 3:          QCA8888 IEEE 802.11a/n/ac
Bluetooth:       Qualcomm CSR8811 (A12U)
Zigbee:          Silicon Labs EM3581 NCP + Skyworks SE2432L
Ethernet:        Qualcomm Atheros QCA8072 (2-port)
Flash 1:         Mactronix MX30LF4G18AC-XKI
RAM (NAND):      SK hynix H5TC4G63CFR-PBA (512MB)
LED Controller:  NXP PCA9633 (I2C)
Buttons:         Single reset button (GPIO).

- The three WiFis were fully tested and are configured with the same settings as in the vendor firmware.
- The specific board files were submitted to the ATH10k mailing list but I'm still waiting for a reply. They can be removed once they are approved upstream.
- Two ethernet ports are accessible on the device. By default one is configured as WAN and the other one is LAN. They are fully working.

Bluetooth:
========
- Fully working with the following caveats:
  - RFKILL need to be enabled in the kernel.
  - An older version of bluez is needed as bccmd is needed to configure the chip.

Zigbee:
======
- The spidev device is available in the /dev directory.
- GPIOs are configured the same way as in the vendor firmware.
- Tests are on-going. I am working on getting access to the Silicon Labs stack to validate that it is fully working.

Installation:
=========
The squash-factory image can be installed via the Linksys Web UI:
1. Open "http://192.168.1.1/ca" (Change the IP with the IP of your device).
2. Login with your admin password.
3. To enter into the support mode, click on the "CA" link and the bottom of the page.
4. Open the "Connectivity" menu and upload the squash-factory image with the "Choose file" button.
5. Click start. Ignore all the prompts and warnings by click "yes" in all the popups.

The device uses a dual partition mechanism. The device automatically revert to the previous partition after 3 failed boot attempts.
If you want to force the previous firmware to load, you can turn off and then turn on the device for 2 seconds, 3 times in a row.

It can also be done via TFTP:
1. Setup a local TFTP server and configure its IP to 192.168.1.100.
2. Rename your image to "nodes_v2.img" and put it to the TFTP root of your server.
3. Connect to the device through the serial console.
4. Power on device and press enter when prompted to drop into U-Boot.
5. Flash the partition of your choice by typing "run flashimg" or "run flashimg2".
6. Once flashed, enter "reset" to reboot the device.

Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Vincent Tremblay <vincent@vtremblay.dev>
2023-01-15 12:55:38 +01:00
John Audia
2835df54ab kernel: bump 5.10 to 5.10.163
Removed upstreamed:
  generic/101-Use-stddefs.h-instead-of-compiler.h.patch[1]

All patches automatically rebased.

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.163&id=ddd2bb08bd99b7ee4442fbbe0f9b80236fdd71d2

Build system: x86_64
Build-tested: ramips/tplink_archer-a6-v3
Run-tested: ramips/tplink_archer-a6-v3

Signed-off-by: John Audia <therealgraysky@proton.me>
2023-01-14 22:31:38 +01:00
Filip Milivojevic
990419dac3 ramips: cudy wr1300v1 reduce SPI freq to 10000000
Reducing SPI flash frequency allows the build to boot on both old variants
with W25Q128 chip and new variants with XM25QH128C chip.

The old 80000000 value only boots on devices with the W25Q128 flash.

This is also the change Cudy themselves made in their openwrt builds and
their .dts file.

Removed m25p,fast-read as it is not needed with slower speeds.

Signed-off-by: Filip Milivojevic <zekica@gmail.com>
2023-01-14 19:25:06 +01:00
Marcin Gajda
700c47a5f6 ipq40xx: Add support ZTE MF18A
Light and small router ( In Poland operators sells together with MC7010 outdoor modem to provide WIFI inside home).
Device specification

SoC Type: Qualcomm IPQ4019
RAM: 256 MiB
Flash: 128 MiB SPI NAND (Winbond W25N01GV)
ROM: 2MiB SPI Flash (GD25Q16)
Wireless 2.4 GHz (IP4019): b/g/n, 2x2
Wireless 5 GHz (QCA9982): a/n/ac, 3x3
Ethernet: 2xGbE (WAN/LAN1, LAN2)
USB ports: No
Button: 2 (Reset/WPS)
LEDs: 3 external leds: Power (blue) , WiFI (blue and red), SMARTHOME (blue and red) and 1 internal (blue) -- NOTE: Power controls all external led (if down ,all others also not lights even signal is up)
Power: 5VDC, 2,1A via USB-C socket
Bootloader: U-Boot
On board ZWave and Zigbee (EFR32 MG1P232GG..)  modules ( not supported by orginal software )
Installation

 1.Open MF18A case by ungluing rubber pad under the router and unscrew screws, and connect to serial console port,
   with the following pinout, starting from pin 1, which is the topmost pin when the board is upright (reset button on the bottom) :

    VCC (3.3V). Do not use unless you need to source power for the converer from it.
    TX
    RX
    GND

    Default port configuration in U-boot as well as in stock firmware is 115200-8-N-1.

 2.Place OpenWrt initramfs image for the device on a TFTP in the server's root. This example uses Server IP: 192.168.0.2

 3.Connect TFTP server to RJ-45 port (WAN/LAN1).

 4.Power on MF18A , stop in u-Boot (using ESC button) and run u-Boot commands:
    setenv serverip 192.168.0.2
    setenv ipaddr 192.168.0.1
    set fdt_high 0x85000000
    tftpboot 0x84000000 openwrt-ipq40xx-generic-zte_mf18a-initramfs-fit-zImage.itb
    bootm 0x84000000

 5.Please make backup of original partitions, if you think about revert to stock, specially mtd8 (Web UI) and mtd9 (rootFS). Use /tmp as temporary storage and do:

WEB PARITION

cat /dev/mtd8 > /tmp/mtd8.bin
scp /tmp/mtd8.bin root@YOURSERVERIP:/
rm /tmp/mtd8.bin
ROOT PARITION

cat /dev/mtd9 > /tmp/mtd9.bin
scp /tmp/mtd9.bin root@YOURSERVERIP:/
rm /tmp/mtd9.bin

If you are sure ,that you want to flash openwrt, from uBoot, before bootm, clean rootfs partition with command:
nand erase 0x1800000 0x1D00000

 6.Login via ssh or serial and remove stock partitions (default IP 192.168.1.1):
ubiattach -m 9 # it could return error if ubi was attached before or rootfs part was erased before
ubirmvol /dev/ubi0 -N ubi_rootfs # it could return error if rootfs part was erased before
ubirmvol /dev/ubi0 -N ubi_rootfs_data # some devices doesn't have it

 7. Install image via :
sysupgrade -n /tmp/openwrt-ipq40xx-generic-zte_mf18a-squashfs-sysupgrade.bin

previously wgeting bin. Sometimes it could print ubi attach error, but please ignore it if process goes forward.

Back to Stock (!!! need original dump taken from initramfs !!!) -------------

Place mtd8.bin and mtd9.bin initramfs image for the device on a TFTP in the server's root. This example uses Server IP: 192.168.0.2
Connect serial console (115200,8n1) to serial console connector .
Connect TFTP server to RJ-45 port (WAN/LAN1).
rename mtd8.bin to web.img and mtd9.bin to root_uImage_s
Stop in u-Boot (using ESC button) and run u-Boot commands:
This will erase Web and RootFS:
nand erase 0x1000000 0x800000
nand erase 0x1800000 0x1D00000

This will restore RootFS:
tftpboot 0x84000000 root_uImage_s
nand erase 0x1800000 0x1D00000
nand write 0x84000000 0x1800000 0x1D00000

This will restore Web Interface:
tftpboot 0x84000000 web.img
nand erase 0x1000000 0x800000
nand write 0x84000000 0x1000000 0x800000

After first boot on stock firwmare, do a factory reset. Push reset button for 5 seconds so all parameters will be reverted to the one printed on label on bottom of the router

As reference was taken MF289F support by Giammarco Marzano stich86@gmail.com and MF286D by Pawel Dembicki paweldembicki@gmail.com

Signed-off-by: Marcin Gajda <mgajda@o2.pl>
2023-01-14 19:19:36 +01:00
Luo Chongjun
b352124cd2 ath79: Fix glinet ar300m usb not working
glinet forum users reported the problem at
https://forum.gl-inet.com/t/gl-ar300m16-openwrt-22-03-0-rc5-usb-port-power-off-by-default/23199

The current code uses the regulator framework to control the USB power
supply. Although usb0 described in DTS refers to the regulator by
vbus-supply, but there is no code related to regulator implemented
in the USB driver of QCA953X, so the USB of the device cannot work.

Under the regulator framework, adding the regulator-always-on attribute
fixes this problem, but it means that USB power will not be able to be
turned off. Since we need to control the USB power supply in user space,
I didn't find any other better way under the regulator framework of Linux,
so I directly export gpio.

Signed-off-by: Luo Chongjun <luochongjun@gl-inet.com>
2023-01-14 19:13:42 +01:00
Keith Harrison
c13263ca07 ramips: add support for D-Link DIR-1935 A1
Add support for D-Link DIR-1935 A1 based on similarities to DIR-882 A1,
DIR-867 A1 and other DIR-8xx A1 models. Existing DIR-882 A1 openwrt
"factory" firmware installs without modificaitons via the D-Link
Recovery GUI and has no known incompatibilities with the DIR-1935 A1.

Changes to be committed:
       new file:   target/linux/ramips/dts/mt7621_dlink_dir-1935-a1.dts
       modified:   target/linux/ramips/image/mt7621.mk
       modified:   target/linux/ramips/mt7621/base-files/etc/board.d/01_leds

Specifications:
* Board: Not known
* SoC: MediaTek MT7621 Family
* RAM: 128 MB (DDR3)
* Flash: 16 MB (SPI NOR)
* WiFi: MediaTek MT7615 Family (x2)
* Switch: 1 WAN, 4 LAN (Gigabit)
* Ports: 1 USB 3.0
* Buttons: Reset, WiFi Toggle, WPS
* LEDs: Power (green/orange), Internet (green/orange), WiFi 2.4G (green),
        WiFi 5G (green)

Notes:
* 160MHz 5GHz is available in LuCi but does not appear to work (i.e. no
  SSID is visible in wifi scanning apps on other devices) with either
  official DIR-882 A1 firmware or a test build for the DIR-1935 A1 based
  on the 22.03.2 branch. 80 MHz 5GHz works.

Serial port:
* Untested (potential user damage/error)
* Expected to be identical to other DIR-8xx A1 models:
	* Parameters: 57600, 8N1
	* Location: J1 header (close to the Reset, WiFi and WPS buttons)
	* Pinout: 1 - VCC
		  2 - RXD
	          3 - TXD
		  4 - GND

Installation:
* D-Link Recovery GUI: power down the router, press and hold the reset
  button, then re-plug it. Keep the reset button pressed until the power
  LED starts flashing orange, manually assign a static IP address under
  the 192.168.0.xxx subnet (e.g. 192.168.0.2) and go to http://192.168.0.1

* Some modern browsers may have problems flashing via the Recovery GUI,
  if that occurs consider uploading the firmware through cURL:

    curl -v -i -F "firmware=@file.bin" 192.168.0.1

Signed-off-by: Keith Harrison <keithh@protonmail.com>
2023-01-14 19:09:56 +01:00
Felix Baumann
acd3b5e83b ramips: Alternative name Asus RT-AX1800U for Asus RT-AX53U
The Asus RT-AX1800U is identical to the already supported Asus RT-AX53U.
Use the ALT0 buildroot tags to show both devices.

Tested-by: Marian Sarcinschi <znevna@gmail.com>
Signed-off-by: Felix Baumann <felix.bau@gmx.de>
2023-01-14 19:05:41 +01:00
Jo Deisenhofer
f204c812e9 ramips: add support for xiaomi RA75 Range Extender
This device is a 'Range extender' variant of the Xiaomi 4A router.
Its identical to the 100m non-intl/chinese version as much as it can run
the same firmware, differences being form factor, LEDs, WPS button
and one 100M port only.
The stock firmware differs significantly, being 'app managed only'.

Device specification
--------------------
SoC:      MT7628DAN MIPS_24KEc@580MHz 2.4G-n 2x2
WiFi:     MT7612EN 5G-ac 80MHz 2T2R
Flash:    16MB W25Q128BV
DRAM:     64MB built-in SoC
Switch:   built-in SoC
Ethernet: 1x10/100 Mbps
USB:      None
Antennas: 2 x external, non-detachable
LEDs:     2 programmable blue/amber
Buttons:  WPS and reset (hidden)
Housing:  Range Extender / Wall wart
Serial:   115200,8n1

MAC Addresses
-------------
All 3 MACs are read from flash and identical to stock.
Label MAC is WIFI 2G

Installation
------------
No HTML UI on this device, serial console only. The serial connector
is unpopulated but standard size and clearly marked. Flash from the
U-Boot shell at boot by choosing (2) and flashing the sysupgrade file
via tftp.

Recovery/Debricking procedures of the xiaomi 4A and variants should
work, but there currently is no official source for the stock firmware.

Signed-off-by: Jo Deisenhofer <jo.deisenhofer@gmail.com>
2023-01-14 19:02:21 +01:00
Jo Deisenhofer
ab402f3d23 ramips: Move LED definition out of included dtsi into dts
Prepare for a new target with different led definitions that wants to
include this dtsi. The resulting dtb are unchanged, verified with dtdiff

Signed-off-by: Jo Deisenhofer <jo.deisenhofer@gmail.com>
2023-01-14 19:02:20 +01:00
Mikhail Zhilkin
1a35edfbdb ramips: add basic support for TP-Link EC330-G5u v1
This adds basic support for TP-Link EC330-G5u Ver:1.0 router (also known
as TP-Link Archer C9ERT).

Device specification
--------------------
SoC Type: MediaTek MT7621AT
RAM: 128 MiB, Nanya NT5CC64M16GP-DI
Flash: 128 MiB NAND, ESMT F59L1G81MA-25T
Wireless 2.4 GHz (MediaTek MT7615N): b/g/n, 4x4
Wireless 5 GHz (MediaTek MT7615N): a/n/ac, 4x4
Ethernet: 5xGbE (WAN, LAN1, LAN2, LAN3, LAN4)
USB ports: 1xUSB3.0
Button: 4 (Led, WiFi On/Off, Reset, WPS)
LEDs: 7 blue LEDs, 1 orange(amber) LED, 1 white(non-gpio) LED
Power: 12 VDC, 2 A
Connector type: Barrel
Bootloader: First U-Boot (1.1.3), Main U-Boot (1.1.3). Additionally,
original TP-Link firmware contains Image U-Boot (1.1.3).

Serial console (UART)
---------------------
                            V
+-------+-------+-------+-------+
| +3.3V |  GND  |  TX   |  RX   |
+---+---+-------+-------+-------+
    |              J2
    |
    +--- Don't connect

Installation
------------
1. Rename OpenWrt initramfs image to test.bin and place it on tftp server
   with IP 192.168.0.5
2. Attach UART, switch on the router and interrupt the boot process by
   pressing 't'
3. Load and run OpenWrt initramfs image:
      tftpboot
      bootm
4. Once inside OpenWrt, switch to the first boot image:
      fw_setenv BootImage 0
5. Run 'sysupgrade -n' with the sysupgrade OpenWrt image

Back to Stock
-------------
1. Run in the OpenWrt shell:
      fw_setenv BootImage 1
      reboot

Recovery
--------
1. Press Reset button and power on the router
2. Navigate to U-Boot recovery web server (http://192.168.0.1/) and upload
   the OEM firmware

MAC addresses
-------------
+---------+-------------------+-------------------+-------------+
|         | MAC example 1     | MAC example 2     | Algorithm   |
+---------+-------------------+-------------------+-------------+
| label   | 68:ff:7b:xx:xx:f4 | 50:d4:f7:xx:xx:da | label       |
| LAN     | 68:ff:7b:xx:xx:f4 | 50:d4:f7:xx:xx:da | label       |
| WAN     | 72:ff:7b:xx:xx:f5 | 54:d4:f7:xx:xx:db | label+1 [1] |
| WLAN 2g | 68:ff:7b:xx:xx:f4 | 50:d4:f7:xx:xx:da | label       |
| WLAN 5g | 68:ff:7b:xx:xx:f6 | 50:d4:f7:xx:xx:dc | label+2     |
+---------+-------------------+-------------------+-------------+
label MAC address was found in factory at 0x165 (text format
xx:xx:xx:xx:xx:xx).

Notes
-----
[1] WAN MAC address:
   a. First octet of WAN MAC is differ than others and OUI is not related
      to TP-Link company. This probably should be fixed.
   b. Flipping bits in first octet and hex delta are different for the
      different MAC examples:
      +-----------------+----------------+----------------+
      |                 | Example 1      | Example 2      |
      +-----------------+----------------+----------------+
      | LAN             | 68 = 0110 1000 | 50 = 0101 0000 |
      | MAC (1st octet) |         ^ ^ ^  |                |
      +-----------------+----------------+----------------+
      | WAN             | 72 = 0111 0010 | 54 = 0101 0100 |
      | MAC (1st octet) |         ^ ^ ^  |            ^   |
      +-----------------+----------------+----------------+
      | HEX delta       | 0xa            | 0x4            |
      +-----------------+----------------+----------------+
      | DEC delta       | 4              | 4              |
      +-----------------+----------------+----------------+
   c. DEC delta is a constant (4). This looks like a mistake in OEM
      firmware and probably should be fixed.
   Based on the above, I decided to keep correct OUI and make WAN MAC =
   label + 1.

[2] Bootloaders
   The device contains 3 bootloaders:
   - First U-Boot: U-Boot 1.1.3 (Mar 18 2019 - 12:50:24). The First U-Boot
     located on NAND Flash to load next full-feature Uboot.
   - Main U-Boot + its backup: U-Boot 1.1.3 (Mar 18 2019 - 12:50:29). This
     bootloader includes recovery webserver. Requires special uImages to
     continue the boot process:
        0x00 (os0, os1) - firmware uImage
        0x40 (os0, os1) - standalone uImage (OpenWrt kernel is here)
   - Additionally, both slots of the original TP-Link firmware contains
     Image U-Boot: U-Boot 1.1.3 (Oct 16 2019 - 08:14:45). It checks image
     magics and CRCs. We don't use this U-Boot with OpenWrt.

Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
2023-01-14 18:36:33 +01:00
INAGAKI Hiroshi
1f5f2e588a ramips: add support for ELECOM WRC-2533GHBK2-T
ELECOM WRC-2533GHBK2-T is a 2.4/5 GHz band 11ac (Wi-Fi 5) router, based
on MT7621A.

Specification:

- SoC      : MediaTek MT7621A
- RAM      : DDR3 128 MiB
- Flash    : SPI-NOR 16 MiB (Macronix MX25L12835FM2I-10G)
- WLAN     : 2.4/5 GHz 4T4R (2x MediaTek MT7615)
- Ethernet : 10/100/1000 Mbps x5
  - Switch : MediaTek MT7530 (SoC)
- LED/keys : 4x/3x (2x buttons, 1x slide-switch)
- UART     : through-hole on PCB
  - J4: 3.3V, RX, GND, TX from SoC side
  - 57600n8
- Power    : 12 VDC, 1.5 A

Flash instruction using factory image:

1. Boot WRC-2533GHBK2-T normally
2. Access to "http://192.168.2.1/" and open firmware update page
   ("ファームウェア更新")
3. Select the OpenWrt factory image and click apply ("適用") button
4. Wait ~150 seconds to complete flashing

MAC addresses:

LAN    : BC:5C:4C:xx:xx:FD (Config,  "ethaddr" (text))
WAN    : BC:5C:4C:xx:xx:FC (Config,  "wanaddr" (text), Label)
2.4 GHz: BC:5C:4C:xx:xx:FE (Factory, 0x4       (hex))
5 GHz  : BC:5C:4C:xx:xx:FF (Factory, 0x8004    (hex))

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2023-01-14 15:41:00 +01:00
INAGAKI Hiroshi
9fe648166e ramips: separate and update dtsi of ELECOM WRC-2533GHBK-I/GHBK2-T
ELECOM WRC-2533GHBK2-T has the almost same hardware as WRC-2533GHBK-I,
so separate the common parts from dts to dtsi.
Additionaly, add color/function properties to LED nodes and change the
trigger of wlan2g/wlan5g LED to "phy*tpt" trigger.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2023-01-14 15:41:00 +01:00
Markus Stockhausen
c03e458c86 realtek: Follow kernel comment style recommendation
While Linus is fine with longer code lines, comments should still be
within the 80 char limit.

Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
2023-01-13 22:34:16 +01:00
Davide Fioravanti
ea42a04161 realtek: add support for Netgear GS750E
This is an RTL8393-based switch with 48 RJ-45 and 2 SFP ports.

Hardware
--------
SoC:	Realtek RTL8393M
RAM:	128MB DDR3 (Nanya NT5CC64M16GP-DI)
FLASH:	8MB NOR (Macronix MX25L6433F)
ETH:	48x 10/100/1000 Mbps RJ-45 Ethernet
SFP:	2x SFP
BTN:
  - 1x	Reset button
LEDS:
  - 50x	Green-Amber leds: lan/sfp status
  - 1x	Green led: power (Always on)
UART:
  - 115200-8-N-1 (CN3, pin-out on PCB)

Everything works correctly except for the 2 SFP ports that are not
working unless you enable it every boot in U-Boot with the command:
	rtk network on

Installation
------------
You can install Openwrt using one of the following methods.

Warning: flashing OpenWrt will delete your current configuration.
Warning 2: if the -factory.bix file is not available anymore, you must
follow Method 2.

Method 1:
Check the firmware version currently running on your switch. If you are
running FW V1.0.1.10 or greater, you have to download the firmware
V1.0.1.8 from Netgear website and then flash this version. When the
switch restarts, it should be on version V1.0.1.8. Now you can get the
OpenWrt -factory.bix file and then flash it using the OEM web interface.

Method 2 (requires the UART connection):
Boot the -initramfs-kernel.bin image from U-Boot with these commands:
	rtk network on;
	tftpboot 0x8f000000 openwrt-realtek-rtl839x-netgear_gs750e-initramfs-kernel.bin;
	bootm;
And then flash the -sysupgrade.bin file from OpenWrt.

Revert to stock
---------------
Get the stock firmware from the Netgear website and flash it using the
OpenWrt web interface. Remember to not keep the current configuration
and check the "Force upgrade" checkbox

Once reverted to stock the firmware could complain in the UART console
about mtdblock3 and/or mtdblock4 not being mounted correctly but it
seems to work anyway without any problems. Sample error:
	mount: Mounting /dev/mtdblock4 on /mntlog failed: Input/output error

If you want to get rid of these error messages you can boot the
-initramfs-kernel.bin image from U-Boot with these commands:
	rtk network on;
	tftpboot 0x8f000000 openwrt-realtek-rtl839x-netgear_gs750e-initramfs-kernel.bin;
	bootm;

And then erase the corresponding partitions using the command:
	For mtdblock3:
		mtd erase jffs2_cfg
	For mtdblock4:
		mtd erase jffs2_log

Now you can reboot the switch and the errors should be gone

Note
----
To get the SFP ports fully working, all the right GPIOs must be found.
In the GPL sources I found these:
 - GPIO_14: SFP_TX_DIS1;
 - GPIO_19: SFP_TX_DIS0;

Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
2023-01-13 22:28:36 +01:00
Davide Fioravanti
79e0b503a4 realtek: rtl839x: enable driver for virtual mtd_concat devices in config
Enable the driver for the rtl839x target. It's required at least for
Netgear GS750E

Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
2023-01-13 22:22:38 +01:00
John Audia
843e3dace7 kernel: bump 5.15 to 5.15.87
Removed upstreamed:
  generic/hack-5.15/290-net-dsa-mv88e6xxx-depend-on-PTP-conditionally.patch[1]

Build system: x86_64
Build-tested: bcm2711/RPi4B, filogic/xiaomi_redmi-router-ax6000-ubootmod
Run-tested: bcm2711/RPi4B, filogic/xiaomi_redmi-router-ax6000-ubootmod

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.87&id=945e58bdaf6faf6e3f957d182244fa830acddab4

Signed-off-by: John Audia <therealgraysky@proton.me>
2023-01-13 22:04:22 +01:00
Nick Hainke
feeec1e14f archs38: enable 5.15 testing kernel
Add 5.15 as testing kernel.

Tested-by: Evgeniy Didin <didin@synopsys.com>
Signed-off-by: Nick Hainke <vincent@systemli.org>
2023-01-13 21:55:58 +01:00
Nick Hainke
f43dc6fd74 archs38: 5.15: copy config from 5.10
Copy config from 5.10 to 5.15.

Signed-off-by: Nick Hainke <vincent@systemli.org>
2023-01-13 21:55:57 +01:00
Florian Maurer
2e3d1edf59 lantiq: xrx200: Fix wifi LED on o2 box 6431
Wifi LED did not work using phy0radio, which somehow slipped through in
the previous testing

Signed-off-by: Florian Maurer <f.maurer@outlook.de>
2023-01-11 22:01:56 +01:00
Michal Hrusecky
f6b46c9269 mvebu: backport upstream patch to fix COMPHY reset
Upstream commit [1] included in the Linux kernel version 6.2 was
backported to Linux kernels 6.1.4, 6.0.18. It should be possible that it
is going to be backported even to the 5.15 series, but before it happens,
let's include it here.

It was discovered that on SOC Marvell Armada 3720, which is using e.g.
Turris MOX, and if you are also using it with older ARM Trusted Firmware
v1.5, it is not possible to detect connected USB 3.0 devices, but they
are working just fine when connected with USB 2.0 cable. This patch
fixes it.

[1] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/drivers/phy/marvell/phy-mvebu-a3700-comphy.c?id=b01d622d76134e9401970ffd3fbbb9a7051f976a

Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Michal Hrusecky <michal.hrusecky@turris.com>
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
[improve commit description, added tag to the patch]
2023-01-11 21:56:36 +01:00
Petr Štetiar
3b669bc3f3 at91: sam9x,sama5: fix racy SD card image generation
We've few low spec (make -j3) build workers attached to the 22.03
buildbot instance which from time to time exhibit following build
failure during image generation (shortened for brewity):

 + dd bs=512 if=root.ext4 of=openwrt-22.03...sdcard.img.gz.img
 dd: failed to open 'root.ext4': No such file or directory

Thats happening likely due to the fact, that on buildbots we've
`TARGET_PER_DEVICE_ROOTFS=y` which produces differently named filesystem
image in the SD card image target dependency chain:

 make_ext4fs -L rootfs ... root.ext4+pkg=68b329da

and that hardcoded `root.ext4` image filename becomes available from
other Make targets in the later stages. So lets fix this issue by using
IMAGE_ROOTFS Make variable which should contain proper path to the root
filesystem image.

Fixing remaining subtargets ommited in commit 5c3679e39b ("at91:
sama7: fix racy SD card image generation").

Fixes: 5c3679e39b ("at91: sama7: fix racy SD card image generation")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2023-01-11 15:23:18 +01:00
Philip Prindeville
26595eac05 x86: Add APU6 board support for startup detection
The APU6 is similar to the APU4 except for eth0 having
an SFP cage instead of RJ45.

Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
2023-01-11 15:16:53 +01:00
Philip Prindeville
5ffa8d06c8 x86: Add definitions for APU6 platform
The board is similar to an APU4 except it has an SFP cage for eth0.

Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz> [patch refresh]
2023-01-11 15:16:52 +01:00
Petr Štetiar
5c3679e39b at91: sama7: fix racy SD card image generation
We've few low spec (make -j3) build workers attached to the 22.03
buildbot instance which from time to time exhibit following build
failure during image generation:

 + dd bs=512 if=root.ext4 of=openwrt-22.03-snapshot-r20028-43d71ad93e-at91-sama7-microchip_sama7g5-ek-ext4-sdcard.img.gz.img seek=135168 conv=notrunc
 dd: failed to open 'root.ext4': No such file or directory

Thats likely due to the fact, that on buildbots we've
`TARGET_PER_DEVICE_ROOTFS=y` which produces differently named filesystem
image in the SD card image target dependency chain:

 make_ext4fs -L rootfs ... root.ext4+pkg=68b329da

and that hardcoded root.ext4 becomes available from other target in the
later stages. So lets fix this issue by using IMAGE_ROOTFS Make variable
which should contain proper path to the root filesystem image.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2023-01-11 15:16:52 +01:00
Christian Marangi
dca1b92ecd
Revert "TODROP: test for ipq4019 target"
This reverts commit 4eb587f7e0.

Pushed by mistake while merging a pr using script.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2023-01-11 14:29:44 +01:00
Christian Marangi
4eb587f7e0
TODROP: test for ipq4019 target
COMMIT TO DROP

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2023-01-11 14:28:41 +01:00
Christian Marangi
55c32a6ce3
ipq806x: refresh upstreamed patch with kernel version tag
Refresh upstreamed patch with kernel version tag and replace them with
the upstream version.

For krait-cc patch rework them with the upstream changes.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2023-01-10 20:59:21 +01:00
Stijn Tintel
f1aa8f34ff sunxi: switch to kernel 5.15
The testing kernel has been available since early 2022, and is running
fine for several people. Let's switch to it by default.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Tested-by: Karl Palsson <karlp@etactica.com>
Tested-by: Jan-Niklas Burfeind <openwrt@aiyionpri.me>
2023-01-09 21:39:46 +02:00
Stijn Tintel
55f93085bb qoriq: drop unused kernel config
While switching qoriq to kernel 5.15, the config for kernel 5.10 was
left behind. Drop it.

Fixes: 230f2fccd1 ("qoriq: switch to kernel 5.15")
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2023-01-09 21:39:45 +02:00
Hauke Mehrtens
ef3919bea9 layerscape: Add CONFIG_NVMEM_LAYERSCAPE_SFP kernel configuration option
The kernel configuration option is now available on kernel 5.10 and
5.15, add it to the config for 5.15 too.

Fixes: 8dfe69cdfc ("kernel: update nvmem subsystem to the latest upstream")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2023-01-08 18:51:27 +01:00
Hauke Mehrtens
111b183ca9 at91: Add CONFIG_NVMEM_MICROCHIP_OTPC kernel configuration option
The kernel configuration option is now available on kernel 5.10 and
5.15, add it to the config for 5.15 too.

Fixes: 8dfe69cdfc ("kernel: update nvmem subsystem to the latest upstream")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2023-01-08 16:10:49 +01:00
Hauke Mehrtens
0627874594 kernel: Refresh kernel patches
Make the patches apply cleanly again.

Fixes: 8dfe69cdfc ("kernel: update nvmem subsystem to the latest upstream")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2023-01-08 14:55:44 +01:00
Daniel Groth
89eb8b50d1 realtek: dgs-1210-10mp: add full sfp description
Added the full SFP description for both SFP ports (lan9, 10) on D-Link
DGS-1210-10MP, which enables hot-plug detection of SFP modules.
Added the patch to both kernel 5.10 and 5.15 dts files.

Signed-off-by: Daniel Groth <flygarn12@gmail.com>
2023-01-08 11:38:47 +01:00
Arınç ÜNAL
fc33c41c21 ramips: do not use GPIO function on switch pins on certain devices
The pins of the MT7530 switch that translate to GPIO 0, 3, 6, 9 and 12 has
got a function, by default, which does the same thing as the netdev
trigger. Because of bridge offloading on DSA, the netdev trigger won't see
the frames between the switch ports whilst the default function will.

Do not use the GPIO function on switch pins on devices that fall under this
category.

Keep it for:

mt7621_belkin_rt1800.dts: There's only one LED which is for the wan
interface and there's no bridge offloading between the "wan" interface and
other interfaces.

mt7621_yuncore_ax820.dts: There's no bridge offloading between the "wan"
and "lan" interfaces.

Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
2023-01-08 12:31:52 +08:00
Sebastian Schaper
3c31f6b521 ramips: add support for D-Link DAP-X1860 A1
The DAP-X1860 is a wall-plug AX1800 repeater.

Specifications:
- MT7621, 256 MiB RAM, 128 MiB SPI NAND
- MT7915 + MT7975 2x2 802.11ax (DBDC)
- Ethernet: 1 port 10/100/1000
- LED RSSI bargraph (2x green, 1x red/orange), status
  and RSSI LEDs are incorrectly populated red/orange
  (should be red/green according to documentation)

Installation:
- Keep reset button pressed during plug-in
- Web Recovery Updater is at 192.168.0.50
- Upload factory.bin, confirm flashing
  (seems to work best with Chromium-based browsers)

Revert to OEM firmware:
- tar -xvf DAP-X1860_RevA_Firmware_101b94.bin
- openssl enc -d -md md5 -aes-256-cbc -in FWImage.st2 \
  -out FWImage.st1 -k MB0dBx62oXJXDvt12lETWQ==
- tar -xvf FWImage.st1
- flash kernel_DAP-X1860.bin via Recovery

Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
2023-01-07 17:56:10 +01:00
Rafał Miłecki
11759a5bf3 kernel: backport of changes & helpers
This code is required for upcoming NVMEM changes.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2023-01-07 17:45:17 +01:00
Shiji Yang
9a07895729 mt76: add stand-alone MT7622 firmware package
Add a separate firmware package to avoid installing the MT7615 firmware
on all MT7622 target devices by default. Now we only add MT7615 firmware
packages for devices that use MT7615E. This commit also removes the
explicit dependency on kmod-mt7615e to refine the package dependency.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2023-01-07 17:11:00 +01:00
Shiji Yang
fc9dd3f083 mt76: add stand-alone MT7915 firmware package
The mt7915e driver supports MT7915, MT7916 and MT7986 chips. And Only
MT7915 series chips need the MT7915 firmware. To save storage, extract
them from the common code package and create a new package to provide
the firmware.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2023-01-07 17:11:00 +01:00
Shiji Yang
3dbaf89296 ramips: use default lzma dictionary size for better performance
limit dictionary size patch was introduced to solve the well known
"LZMA ERROR 1 - must RESET board to recover" error.
09b6755946 "ramips: limit dictionary size for lzma compression"

It seems that it has failed recently and we can use lzma loader to fix
this error by adding "$(Device/uimage-lzma-loader)". So just remove it
to use the default parameter -d24 for a higher compression ratio.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2023-01-07 16:56:16 +01:00
Hauke Mehrtens
2f847da79d kernel: Refresh kernel patches
Make the patches apply cleanly again.

Fixes: 8dfe69cdfc ("kernel: update nvmem subsystem to the latest upstream")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2023-01-07 14:53:10 +01:00
Rafał Miłecki
a1abf71827 kernel: fix bugs added with mac-address-ascii support
1. Check for -EPROBE_DEFER
If it occurs we have to return immediately. Trying other properties
could result in another error and ignoring -EPROBE_DEFER which has a
special meaning.

2. Check for read result
Assuming property->read() success can result in NULL pointer
dereference. It happens e.g. for "mac-address" with NVMEM cell
containing invalid MAC.

3. Simplify code
Don't move cell reading & nvmem_cell_put() into a loop. Simplify loop
code.

Fixes: ecd81de7a5 ("ath79: add nvmem cell mac-address-ascii support")
Cc: Yousong Zhou <yszhou4tech@gmail.com>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2023-01-07 12:02:30 +01:00
Jan Hoffmann
7c574525ee realtek: don't relocate kernel on HPE 1920 series
This is no longer needed now that the kernel is built with a load
address that matches the one hard-coded in the bootloader.

Signed-off-by: Jan Hoffmann <jan@3e8.eu>
2023-01-07 11:16:59 +01:00
David Bauer
e4a76673ff ath79: combine UniFi AC dual firmware-partitions
In order to maximize the available space on UniFi AC boards using a
dual-image partition layout, combine the two OS partitions into a single
partition.

This allows users to access more usable space for additional packages.

Don't limit the usable image size to the size of a single OS partition.
The initial installation has to be done with an older version of OpenWrt
in case the generated image exceeds the space of a single kernel
partition in the future.

Signed-off-by: David Bauer <mail@david-bauer.net>
2023-01-07 01:32:58 +01:00