9ff15f7ee3a0 devices: add device id for MediaTek MT7992E
94b3a3c1a6c4 devices: add device id for Qualcomm Atheros IPQ5018
9cec6b4dd2df devices: add device id for Qualcomm Atheros QCN6122
Link: https://github.com/openwrt/openwrt/pull/17878
Signed-off-by: Robert Marko <robimarko@gmail.com>
The ccache build relies on doctest, which
is useless and can be disabled.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/17700
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The ccache build requires xxhash, which is download from
the Internet. So add host-build package for xxhash.
Fixes: #16851
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
[ use git source proto ]
Link: https://github.com/openwrt/openwrt/pull/17700
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This downstream patch fixes a bug which could flood the logs with the
following message and would eventually lead to a crash.
ath11k c000000.wifi: failed to send HAL_REO_CMD_UPDATE_RX_QUEUE cmd, tid 0 (-105)
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/17182
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add support for Linksys MX2000 (Atlas 6) and MX5500 (Atlas 6 Pro).
These devices are completely identical except for the secondary wifi
chip used for 5Ghz: QCN6102 is used on MX2000 while QCN9024 is used
on MX5500
Speficiations:
* SoC: Qualcomm IPQ5018 (64-bit dual-core ARM Cortex-A53 @ 1.0Ghz)
* Memory: Winbond W634GU6NB-11 (512 MiB DDR3-933)
* Serial Port: 3v3 TTL 115200n8
* Wi-Fi: IPQ5018 (2x2 2.4 Ghz 802.11b/g/n/ax)
* Wi-Fi: MX2000: QCN6102 (2x2:2 5 Ghz 802.11an/ac/ax)
MX5500: QCN9024 (4x4:4 5 Ghz 802.11an/ac/ax)
* Ethernet: IPQ5018 integrated virtual switch connected to an external
QCA8337 switch (4 Ports 10/100/1000 GBASE-T)
* Flash: Macronix MX35UF2GE4AD (256 MiB)
* LEDs: 1x multi-color PWM LED
* Buttons: 1x WPS (GPIO 27 Active Low)
1x Reset (GPIO 28 Acive Low)
Flash instructions (in case of MX2000, else replace with MX5500 images):
1. On OEM firmware, login to the device (typically at http://192.168.1.1) and click 'CA'
in the bottom right corner -> Connectivity -> Manual Upgrade. Alternatively, browse to
http://<router IP>/fwupdate.html.
Upgrade firmware using openwrt-qualcommax-ipq50xx-linksys_mx2000-squashfs-factory.bin image.
Optionally install on second partition, after first boot check actual partition:
fw_printenv -n boot_part
and install firmware on second partition using command in case of 2:
mtd -r -e kernel -n write openwrt-qualcommax-ipq50xx-linksys_mx2000-squashfs-factory.bin kernel
and in case of 1:
mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq50xx-linksys_mx2000-squashfs-factory.bin alt_kernel
2. Installation using serial connection from OEM firmware (default login: root, password: admin):
fw_printenv -n boot_part
In case of 2:
flash_erase /dev/mtd12 0 0
nandwrite -p /dev/mtd12 openwrt-qualcommax-ipq50xx-linksys_mx2000-squashfs-factory.bin
or in case of 1:
flash_erase /dev/mtd14 0 0
nandwrite -p /dev/mtd14 openwrt-qualcommax-ipq50xx-linksys_mx2000-squashfs-factory.bin
After first boot install firmware on second partition:
mtd -r -e kernel -n write openwrt-qualcommax-ipq50xx-linksys_mx2000-squashfs-factory.bin kernel
or:
mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq50xx-linksys_mx2000-squashfs-factory.bin alt_kernel
3. Back to the OEM firmware.
Download firmware from OEM website:
MX2000: https://support.linksys.com/kb/article/585-en/
MX5500: https://support.linksys.com/kb/article/587-en/
From serial or SSH:
fw_printenv boot_part
in case of 1:
mtd -r -e alt_kernel -n write FW_MX2000_1.1.7.210469_prod.img alt_kernel
else in case of 2:
mtd -r -e kernel -n write FW_MX2000_1.1.7.210469_prod.img kernel
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/17182
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add QCN6122 platform support.
QCN6122 is a PCIe based solution that is attached to and enumerated
by the WPSS (Wireless Processor SubSystem) Q6 processor.
Though it is a PCIe device, since it is not attached to APSS processor
(Application Processor SubSystem), APSS will be unaware of such a decice
and hence it is registered to the APSS processor as a platform device(AHB).
Because of this hybrid nature, it is called as a hybrid bus device.
As such, QCN6122 is a hybrid bus type device and follows the same codepath
as for WCN6750.
This is a reversed engineered and heavily simplified version of below
downstream patch:
https://git.codelinaro.org/clo/qsdk/oss/system/feeds/wlan-open/-/ \
blob/NHSS.QSDK.12.4.5.r2/mac80211/patches/232-ath11k-qcn6122-support.patch
Co-developed-by: George Moussalem <george.moussalem@outlook.com>
Signed-off-by: Sowmiya Sree Elavalagan <ssreeela@codeaurora.org>
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/17182
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add ability to download and package ath11k firmware for QCN6122.
QCN6122 is specific/exclusive to the IPQ5018 platform and firmware
files are publishes in a subdirectory of the IPQ5018 firmware files.
While at it, add support for packaging BDFs for QCN6122 wifi and
update iwinfo to recognize QCN6122 wifi.
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/17182
Signed-off-by: Robert Marko <robimarko@gmail.com>
IPQ5018 uses different BDF and caldb addresses for vairous boards,
so let's support reading these addresses from the device tree.
Signed-off-by: Ziyang Huang <hzyitc@outlook.com>
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/17182
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add ability to download and package ath11k firmware for IPQ5018.
As part of commit 172ccf7, the source is pointed to the new QCA repo.
Until QCA publishes updated firmware for IPQ5018 and QCN6122, we need
to download the firmware from the old QUIC repo. As such, add a new
download routine for IPQ5018/QCN6122 to fetch the firmware files from
the old repo.
While at it, add support for packaging BDFs for IPQ5018-based boards
and update iwinfo to recognize IPQ5018 wifi.
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/17182
Signed-off-by: Robert Marko <robimarko@gmail.com>
Introduce support for the Qualcomm IPQ50xx SoC.
This series adds support for the following components:
- minimal boot support: GCC/pinctrl/watchdog/CPUFreq/SDI (upstreamed)
- USB2 (upstreamed)
- Thermal/Tsens
- PCIe gen2 1&2-lane PHY and controller
- PWM and PWM LED
- QPIC SPI NAND controller
- CMN PLL Block (provider of fixed rate clocks to GCC/ethernet/more.)
- Ethernet: IPQ5018 Internal GE PHY (1 gbps)
- Remoteproc MPD driver for IPQ5018 (2.4G) & QCN6122 (5/6G) Wifi
Co-developed-by: Ziyang Huang <hzyitc@outlook.com>
Signed-off-by: Ziyang Huang <hzyitc@outlook.com>
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/17182
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add support for the Qualcomm IPQ50xx in the QCA NSS dataplane driver.
The QCA implementation uses depracated DMA api calls and a downstream SCM
call, so convert to proper Linux DMA and SCM api calls.
In addition, add fixed-link support to support SGMII which is used to
connect the internal IPQ50xx switch to an external switch (ex. QCA8337)
Co-developed-by: Ziyang Huang <hzyitc@outlook.com>
Signed-off-by: Ziyang Huang <hzyitc@outlook.com>
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/17182
Signed-off-by: Robert Marko <robimarko@gmail.com>
The codename for IPQ50xx is Maple (abbreviated as 'MP'), so let's pass
the codename to allow the QCA-SSDK to build for the IPQ50xx SoC.
In addition, disable compiling the MP_PHY driver in favor of a native
driver being upstreamed.
Co-developed-by: Ziyang Huang <hzyitc@outlook.com>
Signed-off-by: Ziyang Huang <hzyitc@outlook.com>
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/17182
Signed-off-by: Robert Marko <robimarko@gmail.com>
Uses upstream DSA switch modules (rtl8365mb, rtl8366), similar to
RTL8367C and rtl8366rb swconfig drivers.
The package dependencies exclude targets built without kernel CONFIG_OF.
It also fixes the rtl8366rb LED support.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17182
Signed-off-by: Robert Marko <robimarko@gmail.com>
Replace outdated package names, order the remaining.
firewall4 is added again, since it is enabled by default.
The device is not a router by default, so this package
makes no sense in the default config. User can enable it
by theirself, or it will be automatically pulled via
dependency, e.g. luci-app-firewall.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Seems that the common style is to have whitespace around the operators
and the indent is single tab.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
The standard U-Boot boot scripts for Duckbills expect the
Linux kernel and device tree files installed below /boot
within the (ext4) root filesystem.
Also a raw zImage is expected instead of uImage.
Extend the SD card generation accordingly and while at,
install all possible Duckbill DT blobs there.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
The old RTL8231 driver integrated the MDIO bus access with the GPIO
control ops, making this driver not very portable to newer platforms.
It depended on the SoC ID instead of the compatible to determine the
MDIO access register, further complicating portability.
A new MFD driver is now available, which offers proper pin config as
well as optional LED support, which can work on any (bitbanged) MDIO
bus. Now that all devices have been migrated, we can drop the old code.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Fix broken NVMEM ASCII patch for x86 target as it does currently fail
compilation when OF is not compiled.
Also mute a warning for integer from pointer without a cast.
Fixes: 73a6cb983c46 ("generic: add pending support for NVMEM ASCII ENV layout driver")
Link: https://github.com/openwrt/openwrt/pull/17845
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
sf21 contains support for Bananapi BPI-RV2 which is a board available
to the general public. Limit the source-only flag to sf19a2890 instead.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Specification:
- Siflower SF21H8898
- 512MB DDR3, 128MB SPI-NAND and 16MB SPI-NOR
- 5x Gigabit ports (SF23P1240 QSGMII PHY and SF23P1211F RGMII PHY)
- 1x 2.5G port (Airoha EN8811H PHY)
- M.2 Key B slot with USB2.0, PCIEx1 and a NanoSIM card slot
- MiniPCIe slot with USB2.0 and PCIEx1
- 1x USB2.0 port through USB Hub
- PCF8563-compatible RTC
The SoC can only boot from SPI0. Two SPI flash chipselects are connected
to GPIO5 (SPI0 CS) and GPIO36 through a 2x2 jumper. It boots from
SPI-NOR or SPI-NAND depending on how the jumpers are connected.
The firmware can be flashed using U-boot web recovery from Siflower
vendor U-boot.
Link: https://github.com/openwrt/openwrt/pull/17115
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
The same GPIO controller is found on all current Siflower SoCs,
with different number of GPIOs. Add ngpios property instead of
specifying it with dt match data.
Link: https://github.com/openwrt/openwrt/pull/17115
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Move SF19A2890 images into a separated .mk in preparation for
more subtargets.
Link: https://github.com/openwrt/openwrt/pull/17115
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
The three packages base-files, libc and kernel are special, the former
can't be upgraded in place since it's content are modified on startup,
the latter two are virtual packages only used as constraints for the
package manager.
Historically base-files was "locked" via a special OPKG function, the
latter two were hidden from the package index and thereby never picked
as possible upgrade.
Time moved forward and we now have APK and tools like OWUT. The latter
compares available packages with installed packages and generates user
readable output, requiring versions for libc and kernel, too. At the
same time, APK uses a different looking mechanism, which is set during
installation instead of part of the package metadata.
In short, this patch adds version constraints to the three packages,
allowing them to be part of the package index.
Fixes: #17774Fixes: #17775Fixes: efahl/owut#31
Signed-off-by: Paul Spooren <mail@aparcar.org>
This reverts commit 3295f6f1c254cd7e5e5285a05581bf6abbde8999.
It looks like the eeprom gets broken after this change.
I think this change was not tested on a real device before it was
merged.
The MAC addresses will be broken again after this revert.
Fixes: #17818
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Make use of ASCII env NVMEM driver for Linksys EAX devices. This also
fix a problem with Linksys EAX devices where the 2 MAC interface had the
same MAC address causing a conflicts with FDB entry. This got much more
present with the DSA conversion making the system not usable.
To fix this, increment + 1 the MAC address for the WAN interface.
Link: https://github.com/openwrt/openwrt/pull/17839
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add pending patch to support NVMEM ASCII ENV layout driver. This is a
generic driver to handle simple NVMEM partition that store environment
in a simple text format. This is the case for Linksys devinfo partition
that are litterally txt file with format "name=value\n"
Such driver works similar to u-boot,env with a similar format. While at
it also introduce a patch to generalize mac-base handling for also other
layout driver.
Link: https://github.com/openwrt/openwrt/pull/17839
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Fix broken WAN on Linksys EAX and Asrock G10 by incrementing the WAN
interface MAC address + 1. This caused conflicting entry in the FDB
table and caused the WAN port to malfunction with the DSA conversion.
Fixes: #17157Fixes: #15585Fixes: #16604
Link: https://github.com/openwrt/openwrt/pull/17839
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Two commits which made their way into Linux stable broke the SATA
support on the BPi-R64.
Fix this by reverting a node rename which broke DT-overlay application
and import a (still pending) patch re-adding the 'syscon' compatible to
the pciesys clock-controller which also contains phy-mode bits
referenced by the ahci_mtk driver expecting to access them using
syscon_regmap_lookup_by_phandle().
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
b11bff90f2ad r8169: add support for RTL8125BP rev.b
b3593df26ab1 r8169: add support for RTL8125D rev.b
b299ea006928 r8169: adjust version numbering for RTL8126
bb18265c3aba r8169: remove support for chip version 11
2e20bf8cc057 r8169: remove unused flag RTL_FLAG_TASK_RESET_NO_QUEUE_WAKE
e340bff27e63 r8169: copy vendor driver 2.5G/5G EEE advertisement constraints
The EEE advertisement patch has been reworked for linux v6.6 because
phy_set_eee_broken() is only present on linux >= v6.13 and eee_broken_modes
declaration has been converted to a bitmap, so linkmode_set_bit() can't be
used either.
e340bff27eed623fb8e3721aa69e70
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Following the initial support of the Cudy WR3000H with PHY C22 for the 2.5G WAN
interface, several improvements fixing issues with RealTek RTL8221B PHYs have
been merged.
Therefore we can now bring the DT in line with other equipment and declare the
2.5G WAN PHY as C45.
Fixes: 9d66b8b ("mediatek: filogic: Add support for cudy wr3000h")
Signed-off-by: Juan Pedro Paredes Caballero <juanpedro.paredes@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17739
[reword commit description]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
On some but not all devices using the RTL8221B 2.5GBit/s PHY the SerDes
setup sequence may hang under some circumstances (eg. <2500M link
partner present during boot).
RTL8221B-VB-CG 2.5Gbps PHY (C45) mdio-bus:01: rtl822xb_config_init failed: -110
Work-around the issue by performing a hardware reset and subsequent
retry of the SerDes setup, which seems to always succeed.
Doing this requires moving ALDPS setup to config_init (which is anyway
the better place for that) as it otherwise doesn't survive the reset.
Also disable listening on MDIO address 0 which may be used by other PHYs
despite being spec'ed as "broadcast address", as bus activity on address
0 may otherwise confuse the RealTek PHY for good reasons.
Tested-by: Luis Mita <luis@luismita.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This new value points to where firmware can be downloaded. It's not
about a single release but all available firmware releases.
In the next step, this URL should be exposed via `ubus call system
board` as an entry of the `distribution` field. With that value, the
running firmware can check for newer releases.
We already have VERSION_REPO however that's different and only meant for
package managers to download their fitting package indexes/packages.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Link: https://github.com/openwrt/openwrt/pull/17780
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
With the current LED configuration using "mxl,led-config", the WAN LED
stops working after the interface is brought down and up again.
Since the driver also properly supports PHY LEDs now, switch to that
instead. This makes the LED work properly, but requires configuration
from userspace.
Fixes: #17782
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Link: https://github.com/openwrt/openwrt/pull/17785
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add kmod-drm-i915 to the default packages. It was build into the kernel
before and is now build as a kernel module.
Fixes: 77cfe8fd15d3 ("x86: make i915 as a kmod with required firmware")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Link: https://github.com/openwrt/openwrt/pull/17781
Signed-off-by: Robert Marko <robimarko@gmail.com>
Update URL variable to reflect switch to Github for development
The old URL returns HTTP 404
Signed-off-by: Felix Baumann <felix.bau@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/17752
Signed-off-by: Robert Marko <robimarko@gmail.com>
Use 'remove_oem_ubi_volume' function to remove OEM UBI volume before upgrade.
This allows to upgrade even if we have OEM firmware on the second partition.
Applies to Linksys MX4200/MX4300/MX5300/MX8500.
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/14720
Signed-off-by: Robert Marko <robimarko@gmail.com>
Update u-boot env variables only when changes are made.
Applies to Linksys MX4200/MX4300/MX5300/MX8500.
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/14720
Signed-off-by: Robert Marko <robimarko@gmail.com>
Dual firmware devices like Linksys MX4200, MX4300, MX5300 and MX8500 use separate rootfs partition.
This option helps to keep all configuration during upgrade.
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/14720
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add new option to be able to perform upgrade on current partition for dual firmware devices:
"-s stay on current partition (for dual firmware devices)"
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/14720
Signed-off-by: Robert Marko <robimarko@gmail.com>
