mirror of
https://github.com/openwrt/openwrt.git
synced 2025-03-14 16:26:34 +00:00
qualcommax: ipq50xx: add support for Linksys MX2000 and MX5500
Add support for Linksys MX2000 (Atlas 6) and MX5500 (Atlas 6 Pro).
These devices are completely identical except for the secondary wifi
chip used for 5Ghz: QCN6102 is used on MX2000 while QCN9024 is used
on MX5500
Speficiations:
* SoC: Qualcomm IPQ5018 (64-bit dual-core ARM Cortex-A53 @ 1.0Ghz)
* Memory: Winbond W634GU6NB-11 (512 MiB DDR3-933)
* Serial Port: 3v3 TTL 115200n8
* Wi-Fi: IPQ5018 (2x2 2.4 Ghz 802.11b/g/n/ax)
* Wi-Fi: MX2000: QCN6102 (2x2:2 5 Ghz 802.11an/ac/ax)
MX5500: QCN9024 (4x4:4 5 Ghz 802.11an/ac/ax)
* Ethernet: IPQ5018 integrated virtual switch connected to an external
QCA8337 switch (4 Ports 10/100/1000 GBASE-T)
* Flash: Macronix MX35UF2GE4AD (256 MiB)
* LEDs: 1x multi-color PWM LED
* Buttons: 1x WPS (GPIO 27 Active Low)
1x Reset (GPIO 28 Acive Low)
Flash instructions (in case of MX2000, else replace with MX5500 images):
1. On OEM firmware, login to the device (typically at http://192.168.1.1) and click 'CA'
in the bottom right corner -> Connectivity -> Manual Upgrade. Alternatively, browse to
http://<router IP>/fwupdate.html.
Upgrade firmware using openwrt-qualcommax-ipq50xx-linksys_mx2000-squashfs-factory.bin image.
Optionally install on second partition, after first boot check actual partition:
fw_printenv -n boot_part
and install firmware on second partition using command in case of 2:
mtd -r -e kernel -n write openwrt-qualcommax-ipq50xx-linksys_mx2000-squashfs-factory.bin kernel
and in case of 1:
mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq50xx-linksys_mx2000-squashfs-factory.bin alt_kernel
2. Installation using serial connection from OEM firmware (default login: root, password: admin):
fw_printenv -n boot_part
In case of 2:
flash_erase /dev/mtd12 0 0
nandwrite -p /dev/mtd12 openwrt-qualcommax-ipq50xx-linksys_mx2000-squashfs-factory.bin
or in case of 1:
flash_erase /dev/mtd14 0 0
nandwrite -p /dev/mtd14 openwrt-qualcommax-ipq50xx-linksys_mx2000-squashfs-factory.bin
After first boot install firmware on second partition:
mtd -r -e kernel -n write openwrt-qualcommax-ipq50xx-linksys_mx2000-squashfs-factory.bin kernel
or:
mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq50xx-linksys_mx2000-squashfs-factory.bin alt_kernel
3. Back to the OEM firmware.
Download firmware from OEM website:
MX2000: https://support.linksys.com/kb/article/585-en/
MX5500: https://support.linksys.com/kb/article/587-en/
From serial or SSH:
fw_printenv boot_part
in case of 1:
mtd -r -e alt_kernel -n write FW_MX2000_1.1.7.210469_prod.img alt_kernel
else in case of 2:
mtd -r -e kernel -n write FW_MX2000_1.1.7.210469_prod.img kernel
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/17182
Signed-off-by: Robert Marko <robimarko@gmail.com>
This commit is contained in:
George Moussalem
Robert Marko
parent
f76b846eea
commit
398f4a9737
22
package/boot/uboot-envtools/files/qualcommax_ipq50xx
Normal file
22
package/boot/uboot-envtools/files/qualcommax_ipq50xx
Normal file
@ -0,0 +1,22 @@
|
||||
[ -e /etc/config/ubootenv ] && exit 0
|
||||
|
||||
touch /etc/config/ubootenv
|
||||
|
||||
. /lib/uboot-envtools.sh
|
||||
. /lib/functions.sh
|
||||
|
||||
board=$(board_name)
|
||||
|
||||
case "$board" in
|
||||
linksys,mx2000|\
|
||||
linksys,mx5500)
|
||||
idx="$(find_mtd_index u_env)"
|
||||
[ -n "$idx" ] && \
|
||||
ubootenv_add_uci_config "/dev/mtd$idx" "0x0" "0x40000" "0x20000"
|
||||
;;
|
||||
esac
|
||||
|
||||
config_load ubootenv
|
||||
config_foreach ubootenv_add_app_config
|
||||
|
||||
exit 0
|
||||
@ -39,8 +39,10 @@ ALLWIFIBOARDS:= \
|
||||
edimax_cax1800 \
|
||||
linksys_homewrk \
|
||||
linksys_mr7350 \
|
||||
linksys_mx2000 \
|
||||
linksys_mx4200 \
|
||||
linksys_mx5300 \
|
||||
linksys_mx5500 \
|
||||
linksys_mx8500 \
|
||||
linksys_whw03 \
|
||||
netgear_lbr20 \
|
||||
@ -175,8 +177,10 @@ $(eval $(call generate-ipq-wifi-package,edgecore_eap102,Edgecore EAP102))
|
||||
$(eval $(call generate-ipq-wifi-package,edimax_cax1800,Edimax CAX1800))
|
||||
$(eval $(call generate-ipq-wifi-package,linksys_homewrk,Linksys HomeWRK))
|
||||
$(eval $(call generate-ipq-wifi-package,linksys_mr7350,Linksys MR7350))
|
||||
$(eval $(call generate-ipq-wifi-package,linksys_mx2000,Linksys MX2000))
|
||||
$(eval $(call generate-ipq-wifi-package,linksys_mx4200,Linksys MX4200))
|
||||
$(eval $(call generate-ipq-wifi-package,linksys_mx5300,Linksys MX5300))
|
||||
$(eval $(call generate-ipq-wifi-package,linksys_mx5500,Linksys MX5500))
|
||||
$(eval $(call generate-ipq-wifi-package,linksys_mx8500,Linksys MX8500))
|
||||
$(eval $(call generate-ipq-wifi-package,linksys_whw03,Linksys WHW03))
|
||||
$(eval $(call generate-ipq-wifi-package,netgear_lbr20,Netgear LBR20))
|
||||
|
||||
@ -0,0 +1,325 @@
|
||||
#include "ipq5018.dtsi"
|
||||
#include "ipq5018-ess.dtsi"
|
||||
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
#include <dt-bindings/leds/common.h>
|
||||
|
||||
/ {
|
||||
|
||||
aliases {
|
||||
ethernet0 = &dp1;
|
||||
ethernet1 = &dp2;
|
||||
led-boot = &led_system_blue;
|
||||
led-failsafe = &led_system_red;
|
||||
led-running = &led_system_blue;
|
||||
led-upgrade = &led_system_red;
|
||||
serial0 = &blsp1_uart1;
|
||||
};
|
||||
|
||||
chosen {
|
||||
bootargs-append = " root=/dev/ubiblock0_0 coherent_pool=2M";
|
||||
stdout-path = "serial0:115200n8";
|
||||
};
|
||||
|
||||
keys {
|
||||
compatible = "gpio-keys";
|
||||
pinctrl-0 = <&button_pins>;
|
||||
pinctrl-names = "default";
|
||||
|
||||
wps-button {
|
||||
label = "wps";
|
||||
gpios = <&tlmm 27 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_WPS_BUTTON>;
|
||||
};
|
||||
|
||||
reset-button {
|
||||
label = "reset";
|
||||
gpios = <&tlmm 28 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_RESTART>;
|
||||
};
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "pwm-leds";
|
||||
|
||||
led_system_red: red {
|
||||
color = <LED_COLOR_ID_RED>;
|
||||
function = LED_FUNCTION_POWER;
|
||||
pwms = <&pwm 3 1250000>;
|
||||
max-brightness = <255>;
|
||||
};
|
||||
|
||||
green {
|
||||
color = <LED_COLOR_ID_GREEN>;
|
||||
function = LED_FUNCTION_POWER;
|
||||
pwms = <&pwm 0 1250000>;
|
||||
max-brightness = <255>;
|
||||
};
|
||||
|
||||
led_system_blue: blue {
|
||||
color = <LED_COLOR_ID_BLUE>;
|
||||
function = LED_FUNCTION_POWER;
|
||||
pwms = <&pwm 1 1250000>;
|
||||
max-brightness = <255>;
|
||||
};
|
||||
};
|
||||
|
||||
reserved-memory {
|
||||
q6_mem_regions: q6_mem_regions@4b000000 {
|
||||
no-map;
|
||||
reg = <0x0 0x4b000000 0x0 0x3000000>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&sleep_clk {
|
||||
clock-frequency = <32000>;
|
||||
};
|
||||
|
||||
&xo_board_clk {
|
||||
clock-frequency = <24000000>;
|
||||
};
|
||||
|
||||
&blsp1_uart1 {
|
||||
status = "okay";
|
||||
|
||||
pinctrl-0 = <&serial_0_pins>;
|
||||
pinctrl-names = "default";
|
||||
};
|
||||
|
||||
&crypto {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&cryptobam {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&prng {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&pwm {
|
||||
status = "okay";
|
||||
|
||||
#pwm-cells = <2>;
|
||||
pinctrl-0 = <&pwm_pins>;
|
||||
pinctrl-names = "default";
|
||||
};
|
||||
|
||||
&qfprom {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&qpic_bam {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&qpic_nand {
|
||||
pinctrl-0 = <&qpic_pins>;
|
||||
pinctrl-names = "default";
|
||||
status = "okay";
|
||||
|
||||
partitions {
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
nand@0 {
|
||||
compatible = "spi-nand";
|
||||
reg = <0>;
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
nand-ecc-engine = <&qpic_nand>;
|
||||
|
||||
nand-ecc-strength = <8>;
|
||||
nand-ecc-step-size = <512>;
|
||||
nand-bus-width = <8>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "0:SBL1";
|
||||
reg = <0x00000000 0x80000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@80000 {
|
||||
label = "0:MIBIB";
|
||||
reg = <0x00080000 0x80000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@100000 {
|
||||
label = "0:QSEE";
|
||||
reg = <0x00100000 0x100000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@200000 {
|
||||
label = "0:DEVCFG";
|
||||
reg = <0x00200000 0x40000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@240000 {
|
||||
label = "0:CDT";
|
||||
reg = <0x00240000 0x40000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@280000 {
|
||||
label = "0:APPSBLENV";
|
||||
reg = <0x00280000 0x80000>;
|
||||
};
|
||||
|
||||
partition@300000 {
|
||||
label = "0:APPSBL";
|
||||
reg = <0x00300000 0x140000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@440000 {
|
||||
label = "0:ART";
|
||||
reg = <0x00440000 0x100000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@540000 {
|
||||
label = "0:TRAINING";
|
||||
reg = <0x00540000 0x80000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@5c0000 {
|
||||
label = "u_env";
|
||||
reg = <0x005c0000 0x80000>;
|
||||
};
|
||||
|
||||
partition@640000 {
|
||||
label = "s_env";
|
||||
reg = <0x00640000 0x40000>;
|
||||
};
|
||||
|
||||
partition@680000 {
|
||||
label = "devinfo";
|
||||
reg = <0x00680000 0x40000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@6c0000 {
|
||||
label = "kernel";
|
||||
reg = <0x006c0000 0x5200000>;
|
||||
};
|
||||
|
||||
partition@ec0000 {
|
||||
label = "rootfs";
|
||||
reg = <0x0ec0000 0x4a00000>;
|
||||
};
|
||||
|
||||
partition@58c0000 {
|
||||
label = "alt_kernel";
|
||||
reg = <0x058c0000 0x5200000>;
|
||||
};
|
||||
|
||||
partition@60c0000 {
|
||||
label = "alt_rootfs";
|
||||
reg = <0x060c0000 0x4a00000>;
|
||||
};
|
||||
|
||||
partition@aac0000 {
|
||||
label = "sysdiag";
|
||||
reg = <0x0aac0000 0x200000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@acc0000 {
|
||||
label = "syscfg";
|
||||
reg = <0x0acc0000 0x4400000>;
|
||||
read-only;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&tlmm {
|
||||
button_pins: button-state {
|
||||
pins = "gpio27", "gpio28";
|
||||
function = "gpio";
|
||||
drive-strength = <8>;
|
||||
bias-pull-up;
|
||||
};
|
||||
|
||||
mdio1_pins: mdio-state {
|
||||
mdc-pins {
|
||||
pins = "gpio36";
|
||||
function = "mdc";
|
||||
drive-strength = <8>;
|
||||
bias-pull-up;
|
||||
};
|
||||
|
||||
mdio-pins {
|
||||
pins = "gpio37";
|
||||
function = "mdio";
|
||||
drive-strength = <8>;
|
||||
bias-pull-up;
|
||||
};
|
||||
};
|
||||
|
||||
pwm_pins: pwm-state {
|
||||
mux_1 {
|
||||
pins = "gpio1";
|
||||
function = "pwm1";
|
||||
drive-strength = <8>;
|
||||
};
|
||||
|
||||
mux_2 {
|
||||
pins = "gpio30";
|
||||
function = "pwm3";
|
||||
drive-strength = <8>;
|
||||
};
|
||||
|
||||
mux_3 {
|
||||
pins = "gpio46";
|
||||
function = "pwm0";
|
||||
drive-strength = <8>;
|
||||
};
|
||||
};
|
||||
|
||||
qpic_pins: qpic-state {
|
||||
clock-pins {
|
||||
pins = "gpio9";
|
||||
function = "qspi_clk";
|
||||
drive-strength = <8>;
|
||||
bias-disable;
|
||||
};
|
||||
|
||||
cs-pins {
|
||||
pins = "gpio8";
|
||||
function = "qspi_cs";
|
||||
drive-strength = <8>;
|
||||
bias-disable;
|
||||
};
|
||||
|
||||
data-pins {
|
||||
pins = "gpio4", "gpio5", "gpio6", "gpio7";
|
||||
function = "qspi_data";
|
||||
drive-strength = <8>;
|
||||
bias-disable;
|
||||
};
|
||||
};
|
||||
|
||||
serial_0_pins: uart0-state {
|
||||
pins = "gpio20", "gpio21";
|
||||
function = "blsp0_uart0";
|
||||
bias-disable;
|
||||
};
|
||||
};
|
||||
|
||||
&tsens {
|
||||
status = "okay";
|
||||
};
|
||||
@ -0,0 +1,262 @@
|
||||
/dts-v1/;
|
||||
|
||||
#include "ipq5018.dtsi"
|
||||
#include "ipq5018-mx-base.dtsi"
|
||||
|
||||
/ {
|
||||
model = "Linksys MX2000";
|
||||
compatible = "linksys,mx2000", "qcom,ipq5018";
|
||||
};
|
||||
|
||||
/*
|
||||
* ===============================================================
|
||||
* _______________________ _______________________
|
||||
* | IPQ5018 | | QCA8337 |
|
||||
* | +------+ +--------+ | | +--------+ +------+ |
|
||||
* | | MAC0 |---| GE Phy | | | | Phy0 |---| MAC1 | |
|
||||
* | +------+ +--------+ | | +--------+ +------+ |
|
||||
* | +------+ +--------+ | | +--------+ +------+ |
|
||||
* | | MAC1 |---| Uniphy |-+-SGMII-+-| SerDes |---| MAC6 | |
|
||||
* | +------+ +--------+ | | +--------+ +------+ |
|
||||
* |_______________________| |_______________________|
|
||||
*
|
||||
* ===============================================================
|
||||
*/
|
||||
|
||||
&switch {
|
||||
status = "okay";
|
||||
|
||||
switch_mac_mode = <MAC_MODE_SGMII_CHANNEL0>;
|
||||
|
||||
qcom,port_phyinfo {
|
||||
// MAC0 -> GE Phy -> QCA8337 Phy4
|
||||
port@0 {
|
||||
port_id = <1>;
|
||||
mdiobus = <&mdio0>;
|
||||
phy_address = <7>;
|
||||
};
|
||||
|
||||
// MAC1 ---SGMII---> QCA8337 SerDes
|
||||
port@1 {
|
||||
port_id = <2>;
|
||||
forced-speed = <1000>;
|
||||
forced-duplex = <1>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
// MAC1 ---SGMII---> QCA8337 SerDes
|
||||
&dp2 {
|
||||
status = "okay";
|
||||
phy-mode = "sgmii";
|
||||
|
||||
fixed-link {
|
||||
speed = <1000>;
|
||||
full-duplex;
|
||||
};
|
||||
};
|
||||
|
||||
&mdio0 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
/* IPQ5018 GE Phy -> Not connected
|
||||
* needs to be enabled for QSDK to identify the IPQ5018 dummy switch
|
||||
*/
|
||||
&ge_phy {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&mdio1 {
|
||||
status = "okay";
|
||||
|
||||
pinctrl-0 = <&mdio1_pins>;
|
||||
pinctrl-names = "default";
|
||||
reset-gpios = <&tlmm 39 GPIO_ACTIVE_LOW>;
|
||||
|
||||
// QCA8337 Phy0 not connected
|
||||
qca8337_0: ethernet-phy@0 {
|
||||
reg = <0>;
|
||||
};
|
||||
|
||||
// QCA8337 Phy1 -> WAN
|
||||
qca8337_1: ethernet-phy@1 {
|
||||
reg = <1>;
|
||||
};
|
||||
|
||||
// QCA8337 Phy2 -> LAN1
|
||||
qca8337_2: ethernet-phy@2 {
|
||||
reg = <2>;
|
||||
};
|
||||
|
||||
// QCA8337 Phy3 -> LAN2
|
||||
qca8337_3: ethernet-phy@3 {
|
||||
reg = <3>;
|
||||
};
|
||||
|
||||
// QCA8337 Phy4 -> LAN3
|
||||
qca8337_4: ethernet-phy@4 {
|
||||
reg = <4>;
|
||||
};
|
||||
|
||||
// QCA8337 switch
|
||||
switch1: ethernet-switch@17 {
|
||||
compatible = "qca,qca8337";
|
||||
reg = <17>;
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
ports {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
port@2 {
|
||||
reg = <2>;
|
||||
label = "wan";
|
||||
phy-handle = <&qca8337_1>;
|
||||
};
|
||||
|
||||
port@3 {
|
||||
reg = <3>;
|
||||
label = "lan3";
|
||||
phy-handle = <&qca8337_2>;
|
||||
};
|
||||
|
||||
port@4 {
|
||||
reg = <4>;
|
||||
label = "lan2";
|
||||
phy-handle = <&qca8337_3>;
|
||||
};
|
||||
|
||||
port@5 {
|
||||
reg = <5>;
|
||||
label = "lan1";
|
||||
phy-handle = <&qca8337_4>;
|
||||
};
|
||||
|
||||
port@6 {
|
||||
reg = <6>;
|
||||
label = "cpu";
|
||||
phy-mode = "sgmii";
|
||||
ethernet = <&dp2>;
|
||||
qca,sgmii-enable-pll;
|
||||
|
||||
fixed-link {
|
||||
speed = <1000>;
|
||||
full-duplex;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&q6v5_wcss {
|
||||
status = "okay";
|
||||
|
||||
memory-region = <&q6_mem_regions>;
|
||||
firmware-name = "ath11k/IPQ5018/hw1.0/q6_fw.mdt",
|
||||
"ath11k/IPQ5018/hw1.0/m3_fw.mdt",
|
||||
"ath11k/QCN6122/hw1.0/m3_fw.mdt";
|
||||
|
||||
/* The QCN6102 radio should map to UPD ID 2. Without */
|
||||
/* bootargs, the firmware will expect it to be on UPD ID 3 */
|
||||
boot-args = <
|
||||
/* type: */ 0x1 /* PCIE0 */
|
||||
/* length: */ 4
|
||||
/* UPD ID: */ 2
|
||||
/* reset GPIO: */ 15
|
||||
/* reserved: */ 0 0>;
|
||||
|
||||
// IPQ5018
|
||||
q6_wcss_pd1: pd-1 {
|
||||
firmware-name = "ath11k/IPQ5018/hw1.0/q6_fw.mdt";
|
||||
|
||||
resets =
|
||||
<&gcc GCC_WCSSAON_RESET>,
|
||||
<&gcc GCC_WCSS_BCR>,
|
||||
<&gcc GCC_CE_BCR>;
|
||||
reset-names =
|
||||
"wcss_aon_reset",
|
||||
"wcss_reset",
|
||||
"ce_reset";
|
||||
|
||||
clocks =
|
||||
<&gcc GCC_WCSS_AHB_S_CLK>,
|
||||
<&gcc GCC_WCSS_ACMT_CLK>,
|
||||
<&gcc GCC_WCSS_AXI_M_CLK>;
|
||||
clock-names =
|
||||
"gcc_wcss_ahb_s_clk",
|
||||
"gcc_wcss_acmt_clk",
|
||||
"gcc_wcss_axi_m_clk";
|
||||
|
||||
// qcom,halt-regs = <&tcsr_q6_block 0xa000 0xd000 0x0>;
|
||||
interrupts-extended =
|
||||
<&wcss_smp2p_in 8 IRQ_TYPE_NONE>,
|
||||
<&wcss_smp2p_in 9 IRQ_TYPE_NONE>,
|
||||
<&wcss_smp2p_in 12 IRQ_TYPE_NONE>,
|
||||
<&wcss_smp2p_in 11 IRQ_TYPE_NONE>;
|
||||
interrupt-names =
|
||||
"fatal",
|
||||
"ready",
|
||||
"spawn-ack",
|
||||
"stop-ack";
|
||||
|
||||
qcom,smem-states =
|
||||
<&wcss_smp2p_out 8>,
|
||||
<&wcss_smp2p_out 9>,
|
||||
<&wcss_smp2p_out 10>;
|
||||
qcom,smem-state-names =
|
||||
"shutdown",
|
||||
"stop",
|
||||
"spawn";
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
// QCN6102 5G
|
||||
q6_wcss_pd2: pd-2 {
|
||||
firmware-name = "ath11k/IPQ5018/hw1.0/q6_fw.mdt";
|
||||
|
||||
interrupts-extended =
|
||||
<&wcss_smp2p_in 16 IRQ_TYPE_NONE>,
|
||||
<&wcss_smp2p_in 17 IRQ_TYPE_NONE>,
|
||||
<&wcss_smp2p_in 20 IRQ_TYPE_NONE>,
|
||||
<&wcss_smp2p_in 19 IRQ_TYPE_NONE>;
|
||||
interrupt-names =
|
||||
"fatal",
|
||||
"ready",
|
||||
"spawn-ack",
|
||||
"stop-ack";
|
||||
|
||||
qcom,smem-states =
|
||||
<&wcss_smp2p_out 16>,
|
||||
<&wcss_smp2p_out 17>,
|
||||
<&wcss_smp2p_out 18>;
|
||||
qcom,smem-state-names =
|
||||
"shutdown",
|
||||
"stop",
|
||||
"spawn";
|
||||
status = "okay";
|
||||
};
|
||||
};
|
||||
|
||||
&wifi0 {
|
||||
// IPQ5018
|
||||
qcom,rproc = <&q6_wcss_pd1>;
|
||||
qcom,ath11k-calibration-variant = "Linksys-MX2000";
|
||||
qcom,ath11k-fw-memory-mode = <2>;
|
||||
qcom,bdf-addr = <0x4c400000>;
|
||||
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&wifi1 {
|
||||
// QCN6102 5G
|
||||
qcom,rproc = <&q6_wcss_pd2>;
|
||||
qcom,userpd-subsys-name = "q6v5_wcss_userpd2";
|
||||
qcom,ath11k-calibration-variant = "Linksys-MX2000";
|
||||
qcom,ath11k-fw-memory-mode = <2>;
|
||||
qcom,bdf-addr = <0x4d100000>;
|
||||
qcom,m3-dump-addr = <0x4df00000>;
|
||||
|
||||
status = "okay";
|
||||
};
|
||||
@ -0,0 +1,240 @@
|
||||
/dts-v1/;
|
||||
|
||||
#include "ipq5018.dtsi"
|
||||
#include "ipq5018-mx-base.dtsi"
|
||||
|
||||
/ {
|
||||
model = "Linksys MX5500";
|
||||
compatible = "linksys,mx5500", "qcom,ipq5018";
|
||||
};
|
||||
|
||||
/*
|
||||
* ===============================================================
|
||||
* _______________________ _______________________
|
||||
* | IPQ5018 | | QCA8337 |
|
||||
* | +------+ +--------+ | | +--------+ +------+ |
|
||||
* | | MAC0 |---| GE Phy | | | | Phy0 |---| MAC1 | |
|
||||
* | +------+ +--------+ | | +--------+ +------+ |
|
||||
* | +------+ +--------+ | | +--------+ +------+ |
|
||||
* | | MAC1 |---| Uniphy |-+-SGMII-+-| SerDes |---| MAC6 | |
|
||||
* | +------+ +--------+ | | +--------+ +------+ |
|
||||
* |_______________________| |_______________________|
|
||||
*
|
||||
* ===============================================================
|
||||
*/
|
||||
|
||||
&switch {
|
||||
status = "okay";
|
||||
|
||||
switch_mac_mode = <MAC_MODE_SGMII_CHANNEL0>;
|
||||
|
||||
qcom,port_phyinfo {
|
||||
// MAC0 -> GE Phy -> QCA8337 Phy4
|
||||
port@0 {
|
||||
port_id = <1>;
|
||||
mdiobus = <&mdio0>;
|
||||
phy_address = <7>;
|
||||
};
|
||||
|
||||
// MAC1 ---SGMII---> QCA8337 SerDes
|
||||
port@1 {
|
||||
port_id = <2>;
|
||||
forced-speed = <1000>;
|
||||
forced-duplex = <1>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
// MAC1 ---SGMII---> QCA8337 SerDes
|
||||
&dp2 {
|
||||
status = "okay";
|
||||
phy-mode = "sgmii";
|
||||
|
||||
fixed-link {
|
||||
speed = <1000>;
|
||||
full-duplex;
|
||||
};
|
||||
};
|
||||
|
||||
&mdio0 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
/* IPQ5018 GE Phy -> Not connected
|
||||
* needs to be enabled for QSDK to identify the IPQ5018 dummy switch
|
||||
*/
|
||||
&ge_phy {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&mdio1 {
|
||||
status = "okay";
|
||||
|
||||
pinctrl-0 = <&mdio1_pins>;
|
||||
pinctrl-names = "default";
|
||||
reset-gpios = <&tlmm 39 GPIO_ACTIVE_LOW>;
|
||||
|
||||
// QCA8337 Phy0 not connected
|
||||
qca8337_0: ethernet-phy@0 {
|
||||
reg = <0>;
|
||||
};
|
||||
|
||||
// QCA8337 Phy1 -> WAN
|
||||
qca8337_1: ethernet-phy@1 {
|
||||
reg = <1>;
|
||||
};
|
||||
|
||||
// QCA8337 Phy2 -> LAN1
|
||||
qca8337_2: ethernet-phy@2 {
|
||||
reg = <2>;
|
||||
};
|
||||
|
||||
// QCA8337 Phy3 -> LAN2
|
||||
qca8337_3: ethernet-phy@3 {
|
||||
reg = <3>;
|
||||
};
|
||||
|
||||
// QCA8337 Phy4 -> LAN3
|
||||
qca8337_4: ethernet-phy@4 {
|
||||
reg = <4>;
|
||||
};
|
||||
|
||||
// QCA8337 switch
|
||||
switch1: ethernet-switch@17 {
|
||||
compatible = "qca,qca8337";
|
||||
reg = <17>;
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
ports {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
port@2 {
|
||||
reg = <2>;
|
||||
label = "wan";
|
||||
phy-handle = <&qca8337_1>;
|
||||
};
|
||||
|
||||
port@3 {
|
||||
reg = <3>;
|
||||
label = "lan3";
|
||||
phy-handle = <&qca8337_2>;
|
||||
};
|
||||
|
||||
port@4 {
|
||||
reg = <4>;
|
||||
label = "lan2";
|
||||
phy-handle = <&qca8337_3>;
|
||||
};
|
||||
|
||||
port@5 {
|
||||
reg = <5>;
|
||||
label = "lan1";
|
||||
phy-handle = <&qca8337_4>;
|
||||
};
|
||||
|
||||
port@6 {
|
||||
reg = <6>;
|
||||
label = "cpu";
|
||||
phy-mode = "sgmii";
|
||||
ethernet = <&dp2>;
|
||||
qca,sgmii-enable-pll;
|
||||
|
||||
fixed-link {
|
||||
speed = <1000>;
|
||||
full-duplex;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&pcie0_phy {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&pcie0 {
|
||||
status = "okay";
|
||||
|
||||
perst-gpios = <&tlmm 15 GPIO_ACTIVE_LOW>;
|
||||
|
||||
bridge@0,0 {
|
||||
reg = <0x00000000 0 0 0 0>;
|
||||
#address-cells = <3>;
|
||||
#size-cells = <2>;
|
||||
ranges;
|
||||
|
||||
wifi@1,0 {
|
||||
status = "okay";
|
||||
|
||||
/* QCN9074: ath11k lacks DT compatible for PCI cards */
|
||||
compatible = "pci17cb,1104";
|
||||
reg = <0x00010000 0 0 0 0>;
|
||||
|
||||
qcom,ath11k-calibration-variant = "Linksys-MX5500";
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&q6v5_wcss {
|
||||
status = "okay";
|
||||
|
||||
memory-region = <&q6_mem_regions>;
|
||||
firmware-name = "ath11k/IPQ5018/hw1.0/q6_fw.mdt",
|
||||
"ath11k/IPQ5018/hw1.0/m3_fw.mdt";
|
||||
|
||||
// IPQ5018
|
||||
q6_wcss_pd1: pd-1 {
|
||||
firmware-name = "ath11k/IPQ5018/hw1.0/q6_fw.mdt";
|
||||
|
||||
resets =
|
||||
<&gcc GCC_WCSSAON_RESET>,
|
||||
<&gcc GCC_WCSS_BCR>,
|
||||
<&gcc GCC_CE_BCR>;
|
||||
reset-names =
|
||||
"wcss_aon_reset",
|
||||
"wcss_reset",
|
||||
"ce_reset";
|
||||
|
||||
clocks =
|
||||
<&gcc GCC_WCSS_AHB_S_CLK>,
|
||||
<&gcc GCC_WCSS_ACMT_CLK>,
|
||||
<&gcc GCC_WCSS_AXI_M_CLK>;
|
||||
clock-names =
|
||||
"gcc_wcss_ahb_s_clk",
|
||||
"gcc_wcss_acmt_clk",
|
||||
"gcc_wcss_axi_m_clk";
|
||||
|
||||
interrupts-extended =
|
||||
<&wcss_smp2p_in 8 0>,
|
||||
<&wcss_smp2p_in 9 0>,
|
||||
<&wcss_smp2p_in 12 0>,
|
||||
<&wcss_smp2p_in 11 0>;
|
||||
interrupt-names =
|
||||
"fatal",
|
||||
"ready",
|
||||
"spawn-ack",
|
||||
"stop-ack";
|
||||
|
||||
qcom,smem-states =
|
||||
<&wcss_smp2p_out 8>,
|
||||
<&wcss_smp2p_out 9>,
|
||||
<&wcss_smp2p_out 10>;
|
||||
qcom,smem-state-names =
|
||||
"shutdown",
|
||||
"stop",
|
||||
"spawn";
|
||||
status = "okay";
|
||||
};
|
||||
};
|
||||
|
||||
&wifi0 {
|
||||
// IPQ5018
|
||||
qcom,rproc = <&q6_wcss_pd1>;
|
||||
qcom,ath11k-calibration-variant = "Linksys-MX5500";
|
||||
qcom,ath11k-fw-memory-mode = <2>;
|
||||
qcom,bdf-addr = <0x4c400000>;
|
||||
|
||||
status = "okay";
|
||||
};
|
||||
@ -0,0 +1,31 @@
|
||||
define Device/linksys_ipq50xx_mx_base
|
||||
$(call Device/FitImageLzma)
|
||||
DEVICE_VENDOR := Linksys
|
||||
BLOCKSIZE := 128k
|
||||
PAGESIZE := 2048
|
||||
KERNEL_SIZE := 8192k
|
||||
IMAGE_SIZE := 83968k
|
||||
NAND_SIZE := 256m
|
||||
SOC := ipq5018
|
||||
IMAGES += factory.bin
|
||||
IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi | linksys-image type=$$$$(DEVICE_MODEL)
|
||||
endef
|
||||
|
||||
define Device/linksys_mx2000
|
||||
$(call Device/linksys_ipq50xx_mx_base)
|
||||
DEVICE_MODEL := MX2000
|
||||
DEVICE_DTS_CONFIG := config@mp03.5-c1
|
||||
DEVICE_PACKAGES := ath11k-firmware-qcn6122 \
|
||||
ipq-wifi-linksys_mx2000
|
||||
endef
|
||||
TARGET_DEVICES += linksys_mx2000
|
||||
|
||||
define Device/linksys_mx5500
|
||||
$(call Device/linksys_ipq50xx_mx_base)
|
||||
DEVICE_MODEL := MX5500
|
||||
DEVICE_DTS_CONFIG := config@mp03.1
|
||||
DEVICE_PACKAGES := kmod-ath11k-pci \
|
||||
ath11k-firmware-qcn9074 \
|
||||
ipq-wifi-linksys_mx5500
|
||||
endef
|
||||
TARGET_DEVICES += linksys_mx5500
|
||||
@ -0,0 +1,45 @@
|
||||
#!/bin/sh
|
||||
|
||||
. /lib/functions/uci-defaults.sh
|
||||
. /lib/functions/system.sh
|
||||
|
||||
ipq50xx_setup_interfaces()
|
||||
{
|
||||
local board="$1"
|
||||
case $board in
|
||||
linksys,mx2000|\
|
||||
linksys,mx5500)
|
||||
ucidef_set_interfaces_lan_wan "lan1 lan2 lan3" "wan"
|
||||
;;
|
||||
esac
|
||||
}
|
||||
|
||||
ipq50xx_setup_macs()
|
||||
{
|
||||
local board="$1"
|
||||
local lan_mac=""
|
||||
local wan_mac=""
|
||||
local label_mac=""
|
||||
|
||||
case "$board" in
|
||||
linksys,mx2000|\
|
||||
linksys,mx5500)
|
||||
label_mac=$(mtd_get_mac_ascii devinfo hw_mac_addr)
|
||||
lan_mac=$label_mac
|
||||
wan_mac=$label_mac
|
||||
ucidef_set_network_device_mac eth0 $label_mac
|
||||
;;
|
||||
esac
|
||||
|
||||
[ -n "$lan_mac" ] && ucidef_set_interface_macaddr "lan" $lan_mac
|
||||
[ -n "$wan_mac" ] && ucidef_set_interface_macaddr "wan" $wan_mac
|
||||
[ -n "$label_mac" ] && ucidef_set_label_macaddr $label_mac
|
||||
}
|
||||
|
||||
board_config_update
|
||||
board=$(board_name)
|
||||
ipq50xx_setup_interfaces $board
|
||||
ipq50xx_setup_macs $board
|
||||
board_config_flush
|
||||
|
||||
exit 0
|
||||
@ -0,0 +1,47 @@
|
||||
#!/bin/sh
|
||||
|
||||
[ -e /lib/firmware/$FIRMWARE ] && exit 0
|
||||
|
||||
. /lib/functions/caldata.sh
|
||||
|
||||
board=$(board_name)
|
||||
|
||||
case "$FIRMWARE" in
|
||||
"ath11k/IPQ5018/hw1.0/cal-ahb-c000000.wifi.bin")
|
||||
case "$board" in
|
||||
linksys,mx2000|\
|
||||
linksys,mx5500)
|
||||
caldata_extract "0:ART" 0x1000 0x20000
|
||||
label_mac=$(mtd_get_mac_ascii devinfo hw_mac_addr)
|
||||
ath11k_patch_mac $(macaddr_add $label_mac 1) 0
|
||||
ath11k_remove_regdomain
|
||||
ath11k_set_macflag
|
||||
;;
|
||||
esac
|
||||
;;
|
||||
"ath11k/QCN6122/hw1.0/cal-ahb-b00a040.wifi1.bin")
|
||||
case "$board" in
|
||||
linksys,mx2000)
|
||||
caldata_extract "0:ART" 0x26800 0x20000
|
||||
label_mac=$(mtd_get_mac_ascii devinfo hw_mac_addr)
|
||||
ath11k_patch_mac $(macaddr_add $label_mac 2) 0
|
||||
ath11k_remove_regdomain
|
||||
ath11k_set_macflag
|
||||
;;
|
||||
esac
|
||||
;;
|
||||
"ath11k/QCN9074/hw1.0/cal-pci-0001:01:00.0.bin")
|
||||
case "$board" in
|
||||
linksys,mx5500)
|
||||
caldata_extract "0:ART" 0x26800 0x20000
|
||||
label_mac=$(mtd_get_mac_ascii devinfo hw_mac_addr)
|
||||
ath11k_patch_mac $(macaddr_add $label_mac 2) 0
|
||||
ath11k_remove_regdomain
|
||||
ath11k_set_macflag
|
||||
;;
|
||||
esac
|
||||
;;
|
||||
*)
|
||||
exit 1
|
||||
;;
|
||||
esac
|
||||
12
target/linux/qualcommax/ipq50xx/base-files/etc/init.d/bootcount
Executable file
12
target/linux/qualcommax/ipq50xx/base-files/etc/init.d/bootcount
Executable file
@ -0,0 +1,12 @@
|
||||
#!/bin/sh /etc/rc.common
|
||||
|
||||
START=99
|
||||
|
||||
boot() {
|
||||
case $(board_name) in
|
||||
linksys,mx2000|\
|
||||
linksys,mx5500)
|
||||
mtd resetbc s_env || true
|
||||
;;
|
||||
esac
|
||||
}
|
||||
@ -0,0 +1,84 @@
|
||||
PART_NAME=firmware
|
||||
REQUIRE_IMAGE_METADATA=1
|
||||
|
||||
RAMFS_COPY_BIN='fw_printenv fw_setenv head'
|
||||
RAMFS_COPY_DATA='/etc/fw_env.config /var/lock/fw_printenv.lock'
|
||||
|
||||
remove_oem_ubi_volume() {
|
||||
local oem_volume_name="$1"
|
||||
local oem_ubivol
|
||||
local mtdnum
|
||||
local ubidev
|
||||
|
||||
mtdnum=$(find_mtd_index "$CI_UBIPART")
|
||||
if [ ! "$mtdnum" ]; then
|
||||
return
|
||||
fi
|
||||
|
||||
ubidev=$(nand_find_ubi "$CI_UBIPART")
|
||||
if [ ! "$ubidev" ]; then
|
||||
ubiattach --mtdn="$mtdnum"
|
||||
ubidev=$(nand_find_ubi "$CI_UBIPART")
|
||||
fi
|
||||
|
||||
if [ "$ubidev" ]; then
|
||||
oem_ubivol=$(nand_find_volume "$ubidev" "$oem_volume_name")
|
||||
[ "$oem_ubivol" ] && ubirmvol "/dev/$ubidev" --name="$oem_volume_name"
|
||||
fi
|
||||
}
|
||||
|
||||
linksys_mx_do_upgrade() {
|
||||
local setenv_script="/tmp/fw_env_upgrade"
|
||||
|
||||
CI_UBIPART="rootfs"
|
||||
boot_part="$(fw_printenv -n boot_part)"
|
||||
if [ -n "$UPGRADE_OPT_USE_CURR_PART" ]; then
|
||||
if [ "$boot_part" -eq "2" ]; then
|
||||
CI_KERNPART="alt_kernel"
|
||||
CI_UBIPART="alt_rootfs"
|
||||
fi
|
||||
else
|
||||
if [ "$boot_part" -eq "1" ]; then
|
||||
echo "boot_part 2" >> $setenv_script
|
||||
CI_KERNPART="alt_kernel"
|
||||
CI_UBIPART="alt_rootfs"
|
||||
else
|
||||
echo "boot_part 1" >> $setenv_script
|
||||
fi
|
||||
fi
|
||||
|
||||
boot_part_ready="$(fw_printenv -n boot_part_ready)"
|
||||
if [ "$boot_part_ready" -ne "3" ]; then
|
||||
echo "boot_part_ready 3" >> $setenv_script
|
||||
fi
|
||||
|
||||
auto_recovery="$(fw_printenv -n auto_recovery)"
|
||||
if [ "$auto_recovery" != "yes" ]; then
|
||||
echo "auto_recovery yes" >> $setenv_script
|
||||
fi
|
||||
|
||||
if [ -f "$setenv_script" ]; then
|
||||
fw_setenv -s $setenv_script || {
|
||||
echo "failed to update U-Boot environment"
|
||||
return 1
|
||||
}
|
||||
fi
|
||||
nand_do_upgrade "$1"
|
||||
}
|
||||
|
||||
platform_check_image() {
|
||||
return 0;
|
||||
}
|
||||
|
||||
platform_do_upgrade() {
|
||||
case "$(board_name)" in
|
||||
linksys,mx2000|\
|
||||
linksys,mx5500)
|
||||
remove_oem_ubi_volume rootfs
|
||||
linksys_mx_do_upgrade "$1"
|
||||
;;
|
||||
*)
|
||||
default_do_upgrade "$1"
|
||||
;;
|
||||
esac
|
||||
}
|
||||
Loading…
x
Reference in New Issue
Block a user