mirror of
https://github.com/openwrt/openwrt.git
synced 2025-03-14 16:26:34 +00:00
siflower: sf21: add support for Bananapi BPI-RV2
Specification: - Siflower SF21H8898 - 512MB DDR3, 128MB SPI-NAND and 16MB SPI-NOR - 5x Gigabit ports (SF23P1240 QSGMII PHY and SF23P1211F RGMII PHY) - 1x 2.5G port (Airoha EN8811H PHY) - M.2 Key B slot with USB2.0, PCIEx1 and a NanoSIM card slot - MiniPCIe slot with USB2.0 and PCIEx1 - 1x USB2.0 port through USB Hub - PCF8563-compatible RTC The SoC can only boot from SPI0. Two SPI flash chipselects are connected to GPIO5 (SPI0 CS) and GPIO36 through a 2x2 jumper. It boots from SPI-NOR or SPI-NAND depending on how the jumpers are connected. The firmware can be flashed using U-boot web recovery from Siflower vendor U-boot. Link: https://github.com/openwrt/openwrt/pull/17115 Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
This commit is contained in:
parent
c057db94f8
commit
b8a8bf53e9
@ -0,0 +1,92 @@
|
||||
/dts-v1/;
|
||||
#include "sf21h8898_bananapi_bpi-rv2.dtsi"
|
||||
|
||||
/ {
|
||||
model = "Bananapi BPI-RV2 (Booting from NAND)";
|
||||
compatible = "bananapi,bpi-rv2-nand", "siflower,sf21h8898";
|
||||
};
|
||||
|
||||
&spi0 {
|
||||
status = "okay";
|
||||
num-cs = <2>;
|
||||
cs-gpios = <&gpio 5 GPIO_ACTIVE_LOW>, <&gpio 36 GPIO_ACTIVE_LOW>;
|
||||
|
||||
flash@0 {
|
||||
compatible = "spi-nand";
|
||||
reg = <0>;
|
||||
spi-max-frequency = <35000000>;
|
||||
spi-tx-bus-width = <2>;
|
||||
spi-rx-bus-width = <2>;
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "fbl";
|
||||
reg = <0x0 0x20000>;
|
||||
};
|
||||
|
||||
partition@20000 {
|
||||
label = "ubi";
|
||||
reg = <0x20000 0x0>;
|
||||
compatible = "linux,ubi";
|
||||
|
||||
volumes {
|
||||
factory: ubi-volume-factory {
|
||||
volname = "factory";
|
||||
|
||||
nvmem-layout {
|
||||
compatible = "fixed-layout";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
macaddr_factory_0: macaddr@0 {
|
||||
compatible = "mac-base";
|
||||
reg = <0x0 0x6>;
|
||||
#nvmem-cell-cells = <1>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
rootdisk: ubi-volume-fit {
|
||||
volname = "fit";
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
flash@1 {
|
||||
compatible = "jedec,spi-nor";
|
||||
reg = <1>;
|
||||
spi-max-frequency = <35000000>;
|
||||
spi-tx-bus-width = <2>;
|
||||
spi-rx-bus-width = <2>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "bootloader-nor";
|
||||
reg = <0x0 0x90000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@90000 {
|
||||
label = "factory-nor";
|
||||
reg = <0x90000 0x10000>;
|
||||
};
|
||||
|
||||
partition@a0000 {
|
||||
label = "firmware-nor";
|
||||
reg = <0xa0000 0xf60000>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
82
target/linux/siflower/dts/sf21h8898_bananapi_bpi-rv2-nor.dts
Normal file
82
target/linux/siflower/dts/sf21h8898_bananapi_bpi-rv2-nor.dts
Normal file
@ -0,0 +1,82 @@
|
||||
/dts-v1/;
|
||||
#include "sf21h8898_bananapi_bpi-rv2.dtsi"
|
||||
|
||||
/ {
|
||||
model = "Bananapi BPI-RV2 (Booting from NOR)";
|
||||
compatible = "bananapi,bpi-rv2-nor", "siflower,sf21h8898";
|
||||
};
|
||||
|
||||
&spi0 {
|
||||
status = "okay";
|
||||
num-cs = <2>;
|
||||
cs-gpios = <&gpio 5 GPIO_ACTIVE_LOW>, <&gpio 36 GPIO_ACTIVE_LOW>;
|
||||
|
||||
flash@0 {
|
||||
compatible = "jedec,spi-nor";
|
||||
reg = <0>;
|
||||
spi-max-frequency = <35000000>;
|
||||
spi-tx-bus-width = <2>;
|
||||
spi-rx-bus-width = <2>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "bootloader";
|
||||
reg = <0x0 0x90000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
factory: partition@90000 {
|
||||
label = "factory";
|
||||
reg = <0x90000 0x10000>;
|
||||
|
||||
nvmem-layout {
|
||||
compatible = "fixed-layout";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
macaddr_factory_0: macaddr@0 {
|
||||
compatible = "mac-base";
|
||||
reg = <0x0 0x6>;
|
||||
#nvmem-cell-cells = <1>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
rootdisk: partition@a0000 {
|
||||
label = "firmware";
|
||||
reg = <0xa0000 0xf60000>;
|
||||
compatible = "denx,fit";
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
flash@1 {
|
||||
compatible = "spi-nand";
|
||||
reg = <1>;
|
||||
spi-max-frequency = <35000000>;
|
||||
spi-tx-bus-width = <2>;
|
||||
spi-rx-bus-width = <2>;
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "fbl-nand";
|
||||
reg = <0x0 0x20000>;
|
||||
};
|
||||
|
||||
partition@20000 {
|
||||
label = "ubi-nand";
|
||||
reg = <0x20000 0x0>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
204
target/linux/siflower/dts/sf21h8898_bananapi_bpi-rv2.dtsi
Normal file
204
target/linux/siflower/dts/sf21h8898_bananapi_bpi-rv2.dtsi
Normal file
@ -0,0 +1,204 @@
|
||||
// SPDX-License-Identifier: (GPL-2.0 OR MIT)
|
||||
/dts-v1/;
|
||||
#include "sf21h8898.dtsi"
|
||||
|
||||
/ {
|
||||
chosen {
|
||||
bootargs = "root=/dev/fit0 rootwait";
|
||||
stdout-path = "serial1:115200n8";
|
||||
rootdisk = <&rootdisk>;
|
||||
};
|
||||
|
||||
memory@20000000 {
|
||||
device_type = "memory";
|
||||
reg = <0x0 0x20000000 0x0 0x20000000>;
|
||||
};
|
||||
|
||||
usb_vbus: regulator@0 {
|
||||
compatible = "regulator-fixed";
|
||||
regulator-name = "usb_vbus";
|
||||
regulator-min-microvolt = <5000000>;
|
||||
regulator-max-microvolt = <5000000>;
|
||||
gpio = <&gpio 37 GPIO_ACTIVE_HIGH>;
|
||||
enable-active-high;
|
||||
};
|
||||
};
|
||||
|
||||
&spi0_pins {
|
||||
pinctrl-single,pins = <
|
||||
SPI0_TXD FUNC_MODE0
|
||||
SPI0_RXD FUNC_MODE0
|
||||
SPI0_CLK FUNC_MODE0
|
||||
SPI0_HOLD FUNC_MODE0
|
||||
SPI0_WP FUNC_MODE0
|
||||
>;
|
||||
};
|
||||
|
||||
&watchdog {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&uart1 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&iomux {
|
||||
rtc_int_gpio: rtc-int-pins {
|
||||
pinctrl-single,pins = <PHY_INT GPIO_MODE>;
|
||||
// disable internal bias as it's externally (and weakly) pulled up
|
||||
pinctrl-single,bias-pullup = <0 SW_PU 0 SW_PU>;
|
||||
pinctrl-single,bias-pulldown = <0 SW_PD 0 SW_PD>;
|
||||
};
|
||||
};
|
||||
|
||||
&i2c0 {
|
||||
status = "okay";
|
||||
|
||||
rtc: rtc@51 {
|
||||
compatible = "analogtek,at8563", "nxp,pcf8563";
|
||||
reg = <0x51>;
|
||||
#clock-cells = <0>;
|
||||
interrupts-extended = <&gpio 40 IRQ_TYPE_LEVEL_LOW>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&rtc_int_gpio>;
|
||||
};
|
||||
};
|
||||
|
||||
&xgmac0 {
|
||||
status = "okay";
|
||||
phy-handle = <&phy1>;
|
||||
nvmem-cells = <&macaddr_factory_0 0>;
|
||||
nvmem-cell-names = "mac-address";
|
||||
};
|
||||
|
||||
&xgmac1 {
|
||||
status = "okay";
|
||||
phy-handle = <&phy2>;
|
||||
nvmem-cells = <&macaddr_factory_0 0>;
|
||||
nvmem-cell-names = "mac-address";
|
||||
};
|
||||
|
||||
&xgmac2 {
|
||||
status = "okay";
|
||||
phy-handle = <&phy3>;
|
||||
nvmem-cells = <&macaddr_factory_0 0>;
|
||||
nvmem-cell-names = "mac-address";
|
||||
};
|
||||
|
||||
&xgmac3 {
|
||||
status = "okay";
|
||||
phy-handle = <&phy4>;
|
||||
nvmem-cells = <&macaddr_factory_0 0>;
|
||||
nvmem-cell-names = "mac-address";
|
||||
};
|
||||
|
||||
&xgmac4 {
|
||||
status = "okay";
|
||||
phy-handle = <&phy15>;
|
||||
nvmem-cells = <&macaddr_factory_0 1>;
|
||||
nvmem-cell-names = "mac-address";
|
||||
mac-address-increment = <1>;
|
||||
/delete-property/ pinctrl-0;
|
||||
};
|
||||
|
||||
&xgmac5 {
|
||||
status = "okay";
|
||||
tx-internal-delay-ps = <2499>;
|
||||
rx-internal-delay-ps = <1519>;
|
||||
phy-mode = "rgmii-txid";
|
||||
phy-handle = <&phy6>;
|
||||
nvmem-cells = <&macaddr_factory_0 0>;
|
||||
nvmem-cell-names = "mac-address";
|
||||
};
|
||||
|
||||
&mdio0 {
|
||||
reset-gpios = <&gpio 30 GPIO_ACTIVE_LOW>;
|
||||
reset-delay-us = <10000>;
|
||||
reset-post-delay-us = <100000>;
|
||||
|
||||
phy1: ethernet-phy@1 {
|
||||
compatible = "ethernet-phy-ieee802.3-c22";
|
||||
reg = <0x1>;
|
||||
};
|
||||
|
||||
phy2: ethernet-phy@2 {
|
||||
compatible = "ethernet-phy-ieee802.3-c22";
|
||||
reg = <0x2>;
|
||||
};
|
||||
|
||||
phy3: ethernet-phy@3 {
|
||||
compatible = "ethernet-phy-ieee802.3-c22";
|
||||
reg = <0x3>;
|
||||
};
|
||||
|
||||
phy4: ethernet-phy@4 {
|
||||
compatible = "ethernet-phy-ieee802.3-c22";
|
||||
reg = <0x4>;
|
||||
};
|
||||
|
||||
phy6: ethernet-phy@6 {
|
||||
compatible = "ethernet-phy-ieee802.3-c22";
|
||||
reg = <0x6>;
|
||||
reset-gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
|
||||
reset-assert-us = <10000>;
|
||||
reset-deassert-us = <100000>;
|
||||
};
|
||||
|
||||
phy15: ethernet-phy@f {
|
||||
compatible = "ethernet-phy-ieee802.3-c22";
|
||||
reg = <0xf>;
|
||||
reset-gpios = <&gpio 39 GPIO_ACTIVE_LOW>;
|
||||
reset-assert-us = <10000>;
|
||||
reset-deassert-us = <100000>;
|
||||
};
|
||||
};
|
||||
|
||||
&pcie_phy {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
/*
|
||||
* M.2 Key B slot. Other GPIO pins connected to the slot:
|
||||
* GPIO0: WAKEUP
|
||||
* GPIO8: W_DISABLE
|
||||
* GPIO10: CLKREQ_N
|
||||
* GPIO38: FULL_CARD_POFF
|
||||
*/
|
||||
&pcie0 {
|
||||
reset-gpios = <&gpio 19 GPIO_ACTIVE_LOW>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
/*
|
||||
* MiniPCIE slot. Other GPIO pins connected to the slot:
|
||||
* GPIO11: PEWAKE
|
||||
* GPIO12: CLKREQ_N
|
||||
*/
|
||||
&pcie1 {
|
||||
reset-gpios = <&gpio 9 GPIO_ACTIVE_LOW>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb_phy {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&dpns {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&edma {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&qsgmii_pcs {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&sgmii_pcs {
|
||||
status = "okay";
|
||||
};
|
@ -18,3 +18,22 @@ define Device/NAND
|
||||
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb with-initrd | pad-to 128k
|
||||
IMAGE/sysupgrade.bin = append-kernel | fit gzip $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb external-static-with-rootfs | append-metadata
|
||||
endef
|
||||
|
||||
define Device/bananapi_bpi-rv2
|
||||
DEVICE_VENDOR := Bananapi
|
||||
DEVICE_PACKAGES := kmod-usb-dwc2 kmod-phy-sf21-usb kmod-phy-airoha-en8811h kmod-rtc-pcf8563
|
||||
endef
|
||||
|
||||
define Device/bananapi_bpi-rv2-nand
|
||||
DEVICE_MODEL := BPi-RV2 (Booting from NAND)
|
||||
DEVICE_DTS := sf21h8898_bananapi_bpi-rv2-nand
|
||||
$(call Device/bananapi_bpi-rv2)
|
||||
endef
|
||||
TARGET_DEVICES += bananapi_bpi-rv2-nand
|
||||
|
||||
define Device/bananapi_bpi-rv2-nor
|
||||
DEVICE_MODEL := BPi-RV2 (Booting from NOR)
|
||||
DEVICE_DTS := sf21h8898_bananapi_bpi-rv2-nor
|
||||
$(call Device/bananapi_bpi-rv2)
|
||||
endef
|
||||
TARGET_DEVICES += bananapi_bpi-rv2-nor
|
||||
|
@ -8,6 +8,9 @@ siflower_setup_interfaces()
|
||||
local board="$1"
|
||||
|
||||
case $board in
|
||||
bananapi,bpi-rv2-n*)
|
||||
ucidef_set_interfaces_lan_wan 'eth0 eth1 eth2 eth3 eth5' 'eth4'
|
||||
;;
|
||||
*)
|
||||
ucidef_set_interfaces_lan_wan 'eth0 eth1 eth2' 'eth3'
|
||||
;;
|
||||
|
@ -5,6 +5,9 @@ platform_do_upgrade() {
|
||||
local board=$(board_name)
|
||||
|
||||
case "$board" in
|
||||
bananapi,bpi-rv2-nand)
|
||||
fit_do_upgrade "$1"
|
||||
;;
|
||||
*)
|
||||
default_do_upgrade "$1"
|
||||
;;
|
||||
|
Loading…
x
Reference in New Issue
Block a user