Some local patches have been sent to upstream and they are slightly
different from the upstream version. So it's better to replace them
to avoid conflicts with the new mac80211 backport driver. The
different parts have been merged into patch 996.
This commit also includes some additional fixes:
* Fix watchdog function.
* Improve MT7620 register initialization.
* Introduce DMA busy watchdog for rt2800.
P.S.
Sometimes rt2800 series chips may fall into a DMA busy state. The
tx queues become very slow and the client cannot connect to the AP.
Usually, We can see a lot of hostapd warnings at this point:
'hostapd: IEEE 802.11: did not acknowledge authentication response'
The DMA busy watchdog can help the driver automatically recover
from this abnormal state. By the way, setting higer 'cell_density'
and disabling 'disassoc_low_ack' can significantly reduce the
probability of the DMA busy.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Kernel 6.1 has introduced support for RTW8822BU network adapter, which
is an USB variant of the rtw8822b 802.11ac chipset family.
Build and install the corresponding module in the rtw88 package
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Current rtw88 build configuration builds modules for all chips supported by
rtw88 driver family. This brings the following issues:
- adding a chip with a different bus is not convenient (all chips currently
depends on PCI)
- some features requirements are not relevant for all chips in family (eg
802.11AC is enforced but RTW88-8723DE is only a 802.11b/g/n chip)
Remove those constraints/issues by adding one module build option per
supported chip, and add intermediate options to properly cascade
dependencies.
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Device specification:
- MT7629 with 16MB NOR flash W25Q128 and 128 MB DDR3 RAM.
- MT7761N and MT7762N wireless chips (currenlty no driver in OpenWrt available)
- WiFi is NOT working on this device
- Dual core but second CPU doesn't seem to work (Error message during boot: "CPU1: failed to come online")
There are two similar merge requests for similar devices with the same issues:
- https://github.com/openwrt/openwrt/pull/12286
- https://github.com/openwrt/openwrt/pull/5084
UART interface is next to the reset button, pinout:
- 1: TX (the pin with the arrow marker)
- 2: RX
- 3: GND
- 4: VCC
UART settings: 115200,8n1, 3.3V
U-Boot menu can be entered by pressing Ctrl+B during startup.
Booting initramfs:
- Set your computers IP adress to 192.168.1.110
- Run a TFTP server providing the initramfs image
- Power on the AP, press Ctrl+B to get to the U-Boot menu
- Select "1. System Load Linux to SDRAM via TFTP"
- Update kernel file name, input server IP and input device IP (if they deviate from the defaults)
- After booting, create a backup of all partitions, especially for kernel and root_fs. They are required for reverting back to stock firmware
- The sysupgrade image can be flashed now
MAC adresses:
- LAN and 2.4GHz use the same MAC (the one printed on the device)
- 5GHz WiFi MAC is LAN MAC + 1
GPIOs:
- GPIO 21 is the reset pin (low active)
- GPIO 55 is for the green LED (active high)
- GPIO 56 is for the yellow/amber LED (active high)
Signed-off-by: Roland Reinl <reinlroland+github@gmail.com>
Specification:
- MT7622BV SoC with 2.4GHz wifi
- MT7975AN + MT7915AN for 5GHz
- MT7531BE Switch
- 512MB RAM
- 128 MB flash
- 3 LEDs (red, orange, white)
- 2 buttons (WPS and Reset)
MAC addresses:
- WAN MAC is stored in partition "Odm" at offset 0x83
- LAN (as printed on the device) is WAN MAC + 1
- WLAN MAC (2.4 GHz) is WAN MAC + 2
- WLAN MAC (5GHz) is WAN MAC + 3
Disassembly: Remove 4 screws in the bottom and 2 screws in the top (after removing the blue cover on the top), then the board can be pulled out.
The pins for the serial console are already labeled on the board (VCC, TX, RX, GND). Serial settings: 3.3V, 115200,8n1
Flashing via Recovery Web Interface:
- Set your IP address to 192.168.0.10, subnetmask 255.255.255.25
- Press the reset button while powering on the deivce
- Keep the reset button pressed until the status LED blinks fast
- Open a Chromium based and goto http://192.168.0.1
- Download openwrt-mediatek-mt7622-dlink_eagle-pro-ai-m32-a1-squashfs-recovery.bin
Flashing via uBoot:
- Open the case, connect to the UART console
- Set your IP address to 10.10.10.3, subnet mask 255.255.255.0. Connect to one of the LAN interfaces of the router
- Run a tftp server which provides openwrt-mediatek-mt7622-dlink_eagle-pro-ai-m32-initramfs-kernel.bin. You can rename the file to iverson_uImage (no extension), then you don't have to enter the whole file name in uboot later.
- Power on the device and select "1. System Load Linux to SDRAM via TFTP." in the boot menu
- Enter image file, tftp server IP and device IP (if they differ from the default).
- TFTP download to RAM will start. After a few seconds OpenWrt initramfs should start
- The initramfs is accessible via 192.168.1.1, change your IP address accordingly (or use multiple IP addresses on your interface)
- Create a backup of the Kernel1 partition, this file is required if a revert to stock should be done later
- Perform a sysupgrade using openwrt-mediatek-mt7622-dlink_eagle-pro-ai-m32-squashfs-sysupgrade.bin
- Reboot the device. OpenWrt should start from flash now
Revert back to stock using the Recovery Web Interface:
- Set your IP address to 192.168.0.10, subnetmask 255.255.255.25
- Press the reset button while powering on the deivce
- Keep the reset button pressed until the status LED blinks fast
- Open a Chromium based and goto http://192.168.0.1
- Flash a decrypted firmware image from D-Link. Decrypting an firmware image is described below.
Decrypting a D-Link firmware image:
- Download https://github.com/RolandoMagico/firmware-utils/blob/M32/src/m32-firmware-util.c
- Compile a binary from the downloaded file, e.g. gcc m32-firmware-util.c -lcrypto -o m32-firmware-util
- Run ./m32-firmware-util M32 --DecryptFactoryImage <OriginalFirmware> <OutputFile>
- Example for firmware 1.03.01_HOTFIX: ./m32-firmware-util M32 --DecryptFactoryImage M32-REVA_1.03.01_HOTFIX.enc.bin M32-REVA_1.03.01_HOTFIX.decrypted.bin
Revert back to stock using uBoot:
- Open the case, connect to the UART console
- Set your IP address to 10.10.10.3, subnet mask 255.255.255.0. Connect to one of the LAN interfaces of the router
- Run a tftp server which provides the previously created backup of the Kernel1 partition. You can rename the file to iverson_uImage (no extension), then you don't have to enter the whole file name in uboot later.
- Power on the device and select "2. System Load Linux Kernel then write to Flash via TFTP." in the boot menu
- Enter image file, tftp server IP and device IP (if they differ from the default).
- TFTP download to FLASH will start. After a few seconds the stock firmware should start again
There is also an image openwrt-mediatek-mt7622-dlink_eagle-pro-ai-m32-a1-squashfs-tftp.bin which can directly be flashed via U-Boot and TFTP. It can be used if no backup of the Kernel1 partition is reuqired.
Flahsing via OEM web interface is currently not possible, the OEM images are encrypted and require a specific memory layout which is not compatible to the partition layout of OpenWrt.
Signed-off-by: Roland Reinl <reinlroland+github@gmail.com>
If /root is created with too permissive permissions, then sshd won't
trust the contents of /root/.ssh as being adequately protected.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
ath9k-htc USB-based adapters also support 5/10MHz channel bandwidth.
Move the code handling the features in debugfs to common-debug.c,
and create proper registration functions to use in debug.c and
htc_drv_debug.c, leaving only debugfs registration there.
While at that, refresh one patch that would conflict otherwise.
Tested on TP-Link Archer C7v2 (ath79) and TP-Link WN722Nv1 (AR9287)
and WN822Nv2 (AR7010+AR9287).
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
ath9k-htc USB-based adapterssupport 5/10MHz channel bandwidth, the
same as standard ath9k ones.
Move the code handling the features in debugfs to common-debug.c,
and create proper registration functions to use in debug.c and
htc_drv_debug.c, leaving only debugfs registration there.
While at that, refresh one patch that would conflict otherwise.
Tested on TP-Link Archer C7v2 (ath79) and TP-Link WN722Nv1 (AR9287)
and WN822Nv2 (AR7010+AR9287).
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
With the case of asking an invalid version that is too big, getver.sh
might return an invalid output in the form of HEAD~-2260475641.
This is caused by BASE_REV - GET_REV using a negative number.
Prevent this by checking if BASE_REV - GET_REV actually return 0 or a
positive number and set REV variable accordingly. With the following
change, invalid revision number will result in unknown printed instead
of the invalid HEAD~-NUMBERS output.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
In-kernel driver for MCS7715 USB-serial bridge has a bool option,
enabling support for parallel port on that chip - which is tied to the
same kernel module. Enable it and select kmod-ppdev, as the image size
increase is minimal and the package isn't bundled in the images by
default.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
This fixes a well known "LZMA ERROR 1" error on Sercomm NA502,
reported on the OpenWrt forum. [1]
[1]: https://forum.openwrt.org/t/176942
Signed-off-by: Szabolcs Hubai <szab.hu@gmail.com>
creates SGE encrypted factory images
to use via the D-Link web interface
rename the old factory unencrypted images to recovery
for use in the recovery console when recovery is needed
DIR-1935-A1 , DIR-853-A1 , DIR-853-A3 , DIR-867-A1 ,
DIR-878-A1 and DIR-882-A1
Signed-off-by: Alan Luck <luckyhome2008@gmail.com>
Since kernel 5.11, the PXA I2C driver has been converted to generic I2C
recovery, which makes the I2C bus completely lock up if recovery pinctrl
is present in the DT and I2C recovery is enabled.
This effectively completely broke I2C on Methode uDPU and eDPU boards
as both of them rely on I2C recovery.
After a discussion upstream, it was concluded that there is no simple fix
and that the blamed upstream commit:
0b01392c18b9993a584f36ace1d61118772ad0ca ("i2c: pxa: move to generic GPIO
recovery") should be reverted.
I have sent the revert upstream, it should be merged soon so lets "fix"
OpenWrt as well.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Adjust our local ath10k-ct patches to the change
from the -ct 6.2 version to 6.4.
This restores e.g. the LED functionality.
Fixes: 7d3651f1b9 ("ath10k-ct: switch to 6.4")
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Commit 947b44d9ae ("ipq807x: fix wrong define for LAN and WAN ess mask")
started fixing wrong switch_lan_bmp that defined lan there weren't
actually present. This displayed a fragility in the malibu phy init code
in qca-ssdk.
Add patch to fix this.
Quoting the patch detailed description:
I'm very confused by this and to me it's not clear the real usage of
this logic.
From what I can see the usage of this is EXTREMELY FRAGILE and results
in dangerous results if the OEM (or anyone that by chance try to
implement things in a logical manner) deviates from the default values
from the "magical template".
To be in more details. With QSDK 12.4, some tweaks were done to improve
autoneg and now on every call of port status, the phydev is tried to
add. This resulted in the call and log spam of an error with ports that
are actually not present on the system with qsdk reporting phydev is
NULL. This itself is not an error and printing the error is correct.
What is actually an error from ages is setting generic bitmap reporting
presence of port that are actually not present. This is very common on
OEM where the switch_lan_bmp is always a variant of 0x1e (that on bitmap
results in PORT1 PORT2 PORT3 PORT4 present) or 0x3e (PORT1 PORT2 PORT3
PORT4 PORT5). Reality is that many device are used as AP with one LAN
port or one WAN port. (or even exotic configuration with PORT1 not
present and PORT2 PORT3 PORT4 present (Xiaomi 3600)
With this finding one can say... ok nice, then lets update the DT and
set the correct bitmap...
Again world is a bad place and reality is that this cause wonderful
regression in some case of by extreme luck the first ever connected
port working and the rest of the switch dead.
The problem has been bisected to all the device that doesn't have the
PORT1 declared in any of the bitmap.
With this perfection in mind, on to the REAL problem.
malibu_phy_hw_init FOR SOME REASON, set a global variable first_phy_addr
to the first detected PHY addr that coincidentally is always PORT1.
PORT1 addr is 0x0. The entire code in malibu_phy use this variable to
derive the phy addrs in some function.
Declaring a bitmap where the PORT1 is missing (or worse PORT4 the only
one connected) result in first_phy_addr set to 1 or whatever phy addr is
detected first setting wrong value all over the init stage.
To fix this, just drop this variable and hardcode everything to assume
the first phy adrr is ALWAYS 0 and remove calculation and use define for
special case.
With the following change normal switch traffic is restored and ports
function is recovered.
Fixes: #13945
Fixes: 947b44d9ae ("ipq807x: fix wrong define for LAN and WAN ess mask")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Information about package license is important, so lets add it.
Fixes: 79ee0d2cee ("debugcc: add new package to debug IPQ based SoC clocks")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
I find myself manually compiling dtc as a staticly linked binary rather
often while porting a new device to OpenWrt as dtc is rarely included in
various vendor modifications of OpenWrt.
So, since dtc offers a convenient meson option to build it as staticaly
linked binary, lets make it a compile time option.
Signed-off-by: Robert Marko <robimarko@gmail.com>
switch_lan_bmp and switch_wan_bmp have wrong values and now cause
problems with the new version of the qca-ssdk.
Fix the wrong entry and drop the redundant switch_cpu_bmp.
Also introduce some convenient define to better understand values in
this map.
Fixes: eea264fead ("kernel: qca-ssdk: update to 12.4")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Tested-by: Robert Marko <robimarko@gmail.com> # Dynalink AX3600 and Qnap 301W
Reviewed by: Robert Marko <robimarko@gmail.com>
eee02ccca8c8 device: add support to configure eee
bb28f6a291d9 wireless: fix sign comparison warning
35facc8306f5 wireless: fix premature removal of hotplug devices due to down state
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Now that netifd and uci-defaults.sh supports a way to setup DSA port
conduit without using iproute2 tool, set DSA port conduit directly in
board.d, that will fill board.d and will instruct netifd to setup the
port.
Drop special init.d qca8k_set_port script and ip-tiny from target dep as
they are not required anymore.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add additional uci-defaults function for configuring GRO settings and
conduit for network devices.
Tweaking the GRO values might increase performance on some low spec
device that lack some offload feature on gmac.
Tweaking conduit interface is specific to DSA based devices and is
useful for multi-CPU scenario where one CPU is dedicated to one single
port.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Generalize ucidef_set_network_device functions to use a more generic
_ucidef_set_network_device_common that takes as args the option and the
value to apply instead of hardcoding.
This is to reduce duplicated code in preparation for addition of
additional option for board.d usage.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
841b05fbb91e system-linux: fix compilation error if IFLA_DSA_MASTER is not supported
5c9ecc1ff74f system-linux: make system_if_get_master_ifindex static
2dc7f450f3a2 system-linux: add option to configure DSA conduit device
838f815db5ef system-linux: add support for configurable GRO option
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Update the devel/gdb package to version 13.2
* Remove the upstreamed patch 001-Add-support-for-readline-8.2.patch
* Adjust 130-gdb-ctrl-c.patch to upstream changes
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Allow selecting KERNEL_SLUB_DEBUG and KERNEL_SLUB_DEBUG_ON manually and
provide detailed help for both.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
From the symbol help message:
> SLUB has extensive debug support features. Disabling these can result
> in significant savings in code size.
There seems to be no need to enable those debugging features for
standard use.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Currently for 802.1s only, for wifi 2.4GHz in g/n mode, 40MHz is never
permitted.
This is probably due to the complexity of setting periodic check for the
intolerant bit. When noscan option is set, we ignore the presence of the
intoleran bit in near AP, so we can enable 40MHz and ignore any complex
logic for checking.
Fixes: #13112
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Also channel 7 for 2.4GHz can be set to HT40PLUS. Permit this and add it
to the list of the channels.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
noscan option for mesh was broken and actually never applied.
This is caused by a typo where ssid->noscan value is check instead of
conf->noscan resulting in the logic swapped and broken.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
noscan option was changed to hostapd_noscan but the entry in
wpa_supplicant was never updated resulting in the noscan option actually
never set.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Update SSDK version to 12.4, this fixes weird SFP port link up/downs
while there is no SFP module plugged in.
Signed-off-by: Robert Marko <robimarko@gmail.com>
SSDK has switched to using the upstream SMEM helper to get the SoC ID and
then look it up in the QCA SMEM ID header, so we need these in order for
SSDK to compile as they are currently undefined.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Update to latest version.
Remove "100-increase-tmpfile-name-length-limit.patch" because project
is now using limits.h with PATH_MAX [0].
Automatically refreshed:
- 030-allow-to-use-different-magic.patch
[0] - 99d430f344
Signed-off-by: Nick Hainke <vincent@systemli.org>
0352a33 uloop: support new interval and signal APIs
1468cc4 syntax: don't treat `as` and `from` as reserved keywords
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
3a07943 block: support skipping uuid check
56a9b4e block: consider currently mounted root device first
9cd09d4 block: try to find the root device on both / and /rom
c1a8d95 block: support extroot on already mounted overlay
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
