This is an automatically generated commit which aids following Kernel patch
history, as git will see the move and copy as a rename thus defeating the
purpose.
For the original discussion see:
https://lists.openwrt.org/pipermail/openwrt-devel/2023-October/041673.html
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
This commit adds the logic required to install OpenWrt on a
Cisco/Viptela vEdge 1000 while nicely integrating with the already
present bootloader and making it possible to roll back to stock OS.
The vEdge 1000 has a built-in SSD with a ext2 partition from which
the stock u-boot boots the Linux kernel from.
In order for Linux not to be confused about which partition the root
file system is on, there are some tricks needed to ensure the partition
is identifiable at boot time. For this we use blkid as part of the
scripts, and sfdisk as part of the manual installation process
documented on the wiki. Thus, those packages have been added as a
platform dependency. Finally, the u-boot environment is updated which
requires the use of uboot-envtools.
Tested on a Cisco vEdge 1000.
Signed-off-by: Christian Svensson <blue@cmd.nu>
Link: https://github.com/openwrt/openwrt/pull/16140
Signed-off-by: Robert Marko <robimarko@gmail.com>
Yuncore CPE200 is an outdoor unit with IEEE 802.11ac radio.
Hardware:
- SoC: MediaTek MT7628DAN (MIPS 580MHz)
- Flash: 8 MiB Spansion S25FL064K
- RAM: 64 MiB (built-into SoC)
- WLAN: 5 GHz (MT7613AE)
- Ethernet: 1x 10/100 Mbps WAN, 1x 10/100 LAN (MT7628)
- Buttons: 1 Reset button, 2 buttons for display UI (unsupported)
- LEDs: 4x Green (Power, LAN, WAN, WiFi)
- Display: 4 digit 7-segment display driven by an additional
microcontroller (unsupported)
- Serial console: unpopulated header, 57600 8n1 (RX only)
- Power: 12 VDC, 1 A
Installation:
The installation can be done via the recovery HTTP server which is built
into the bootloader. Hold down the reset button while connecting the
device to power and keep holding a bit more than 3 seconds. Connect to
http://192.168.0.100/ and upload sysupgrade.bin file.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
er is missing from platform_copy_config() and octeon_move_config(), so
config is lost on every sysupgrade.
Signed-off-by: Jakob Haufe <sur5r@sur5r.net>
Link: https://github.com/openwrt/openwrt/pull/16238
Signed-off-by: Robert Marko <robimarko@gmail.com>
MediaTek SDK uses eth2 as additional LAN port and eth1 as WAN.
Do the same also in OpenWrt to keep settings aligned with the SDK.
Suggested-by: Bc-bocun Chen <bc-bocun.chen@mediatek.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
'SANE' is a protocol for remote access to scanners as implemented by the
'saned' daemon. Like FTP, it uses separate control and data connections.
So let´s enable this in the kernel and add them to 'kmod-nf-nathelper-extra'.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
NetBIOS name service requests are sent as broadcast messages from an
unprivileged port and responded to with unicast messages to the
same port. This make them hard to firewall properly because connection
tracking doesn't deal with broadcasts.
So let´s enable this in the kernel and add them to 'kmod-nf-nathelper-extra'.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Try to do a clean disconnection via L3 request before the connection is
stopped.
Because this might take up to 6 seconds (the driver does 3 attempts with
a timeout of 2 seconds each), a termination timeout needs to be defined
in the init script.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Move the code for disconnection on exit to a separate function, and also
call it in the code paths for SIGINT and the "quit" CLI command.
While at it, make the patch description a bit clearer.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Move the code for disconnection on exit to a separate function, and also
call it in the code path for the "quit" CLI command.
While at it, make the patch description a bit clearer.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Use the correct return value in error message.
Fixes: 6e4c9738be ("ltq-vdsl-vr11-app: add version 4.23.1 for vr11 targets")
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Use the correct return value in error message.
Fixes: 1daaef31b3 ("ltq-vdsl-app: disconnect when service is stopped")
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Drop config and files for Linux 6.1.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16057
Signed-off-by: Robert Marko <robimarko@gmail.com>
Switch to Linux kernel version 6.6.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16057
Signed-off-by: Robert Marko <robimarko@gmail.com>
Userspace handling is deprecated.
Unused wan mac added to dts. Requires DSA to implement.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16246
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Empty trailing fields get lost when the lines are split and merged again
at colons, resulting in unparsable entries. Only use the split fields for
matching against the other file, but emit the original line unchanged
to fix the issue.
Fixes: de7ca7dafa ("base-files: merge /etc/passwd et al at sysupgrade config restore")
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Set and get vlan 4k for rtl8367d family chips
Co-authored-by: Serge Vasilugin <vasilugin@yandex.ru>
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/14804
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Set and get mc index for rtl8367d family chips
Co-authored-by: Serge Vasilugin <vasilugin@yandex.ru>
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/14804
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Set and get ports speed for rtl8367d family chips
Co-authored-by: Serge Vasilugin <vasilugin@yandex.ru>
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/14804
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Detect the RTL8367D chip family and set the appropriate extif
Co-authored-by: Serge Vasilugin <vasilugin@yandex.ru>
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/14804
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* Adds the x86_64 dependency for mlxsw_core
* Removes the redundant mlxsw_core dependency
from mlxsw-minimal and mlxsw-spectrum
* Removes the DCB configuration symbols because
they were moved into the generic configuration
Signed-off-by: Til Kaiser <mail@tk154.de>
Link: https://github.com/openwrt/openwrt/pull/15362
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Disables Data Center Bridging support for some network drivers by
default to avoid compilation errors when CONFIG_DCB is enabled.
Signed-off-by: Til Kaiser <mail@tk154.de>
Link: https://github.com/openwrt/openwrt/pull/15362
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit adds the currently missing Mellanox
Spectrum-2, Spectrum-3, and Spectrum-4 firmware files.
Signed-off-by: Til Kaiser <mail@tk154.de>
Link: https://github.com/openwrt/openwrt/pull/15362
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit adds the missing x86 dependency for
the Mellanox mlxcpld LED driver.
Signed-off-by: Til Kaiser <mail@tk154.de>
Link: https://github.com/openwrt/openwrt/pull/15362
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Radxa ROCK 3B is a Pico-ITX form factor SBC[1] using the Rockchip
RK3568(J).
Hardware
--------
- Rockchip RK3568(J) SoC
- Quad A55 CPU
- Mali-G52 GPU
- 1 TOPS @ INT8 NPU
- 2GB/4GB/8GB LPDDR4 RAM
- eMMC connector
- Micro SD Card slot
- NVMe SSD through the M.2 M Key (2-lane PCIe 3.0)
- SPI Flash for bootloader
- 2x Gigabit ethernet port (one supports PoE with add-on PoE HAT)
- 1x M.2 E Key socket with SDIO, UART and USB interfaces
- 1x M.2 B Key socket with PCIe, SATA, and USB interfaces
- 1x SIM card socket
- 1x USB 3.0 Type-A HOST port
- 1x USB 3.0 Type-A OTG port
- 2x USB 2.0 Type-A HOST ports
- 40 Pin GPIO header
[1] https://radxa.com/products/rock3/3b
Installation
------------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card or
internal eMMC using dd.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://github.com/openwrt/openwrt/pull/16185
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Radxa ROCK 3C is a high-performance, low-cost SBC[1] using the
Rockchip RK3566.
Hardware
--------
- Rockchip RK3566 SoC
- Quad A55 CPU
- Mali-G52-2EE GPU
- 1 TOPS @ INT8 NPU
- 1GB/2GB/4GB LPDDR4 RAM
- eMMC connector
- Micro SD Card slot
- NVMe SSD through the M.2 M Key connector(2230) or M.2 Extension
board(2232/2260/2280)
- SATA through the Radxa Penta SATA HAT
- 1x Gigabit ethernet port(supports PoE with add-on PoE HAT)
- WiFi6/BT5.4 (not supported yet on OpenWrt)
- 1x USB 3.0 Type-A HOST port
- 2x USB 2.0 Type-A HOST ports
- 1x USB 2.0 Type-A OTG port
- 40 Pin GPIO header
[1] https://radxa.com/products/rock3/3c
Installation
------------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card or
internal eMMC using dd.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://github.com/openwrt/openwrt/pull/16185
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Another instance of files in build_dir symlinking to staging_dir. While
the symlinks do not currently cause any bugs in the libtool package,
such symlinks were found to make the build more fragile, as writing to
the symlink may accidentally modify the shared file in staging_dir. Pass
--copy to bootstrap to disable the symlinking.
Link: https://github.com/openwrt/openwrt/pull/15825
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
In Gluon's Github Actions CI, we were occasionally seeing bizarre build
errors that looked like a config.sub file had been corrupted, or changed
while it was being executed.
The cause turned out to be an interaction of the symlinks created by
autoreconf (pointing from individual tools' build dirs into
`staging_dir/host/share/automake-1.16`) and OpenWrt's host-build.mk,
which replaced config.guess and config.sub *after* autoreconf. The
result was that the replacement of these files ended up following the
symlinks and writing the files in `staging_dir/host/share/automake-1.16`
instead of a package's build dir. This could cause other packages' builds
to fail if they were currently executing the scripts while they were
being written.
To fix this, disable autoreconf's symlinking feature, so that modifying
these files in a package's build directory can't accidentally affect the
staged versions.
Link: https://github.com/openwrt/openwrt/pull/15825
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
OpenWRT by default uses the Ninja generator, but some packages disable
Ninja and use the default Unix Makefiles generator. This generator can
be overridden in the user environment with `CMAKE_GENERATOR`. This patch
explicitly sets the correct generator when `PKG_USE_NINJA:=0`.
In particular, the `mt76` package uses the Makefiles generator.
Signed-off-by: Ivan Romanov <drizt72@zoho.eu>
Link: https://github.com/openwrt/openwrt/pull/16263
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>