Migrate to "new" image generation method. Device profiles will be generated
based on image/Makefile instead of profiles/ , which will also allow to
automatically build images for all supported devices via buildbot.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
rk3399 ATF requires arm toolchain to build the m0 pmu driver.
As OpenWrt doesn't ship this toolchain so download the prebuilt one
just like what we did in arm-trusted-firmware-mvebu.
Fixes: 5d1cb52da0 ("arm-trusted-firmware-rockchip: Update to 2.9")
Reported-by: Wurzer Juergen <wurzer.juergen@gmail.com>
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
General specification:
SoC Type: MediaTek MT7620A (580MHz)
ROM: 8 MB SPI-NOR (MX25L6406E)
RAM: 64 MB DDR (W9751G6KB-25)
Switch: MediaTek MT7530
Ethernet: 5 ports - 5×100MbE (WAN, LAN1-4)
Wireless: 2.4 GHz (MediaTek RT5390): b/g/n
Wireless: 5 GHz (MediaTek MT7610EN): ac/n
Buttons: 2 button (POWER, WPS/RESET)
Bootloader: U-Boot 1.1.3
Power: 12 VDC, 0.5 A
MACs:
| LAN | [Factory + 0x04] - 2 |
| WLAN 2.4g | [Factory + 0x04] - 1 |
| WLAN 5g | [Factory + 0x8004] - 3 |
| WAN | [Factory + 0x04] - 2 |
OEM easy installation:
1. Use a PC to browse to http://192.168.0.1.
2. Go to the System section and open the Firmware Update section.
3. Under the Local Update at the right, click on the CHOOSE FILE...
4. When a modal window appears, choose the firmware file and click on
the Open.
5. Next click on the UPDATE FIRMWARE button and upload the firmware image.
Wait for the router to flash and reboot.
OEM installation using the TFTP method (need level converter):
1. Download the latest firmware image.
2. Set up a Tftp server on a PC (e.g. Tftpd32) and place the firmware
image to the root directory of the server.
3. Power off the router and use a twisted pair cable to connect the PC
to any of the router's LAN ports.
4. Configure the network adapter of the PC to use IP address 192.168.0.180
and subnet mask 255.255.255.0.
5. Connect serial port (57600 8N1) and turn on the router.
6. Then interrupt "U-Boot Boot Menu" by hitting 2 key (select "2: Load
system code then write to Flash via TFTP.").
7. Press Y key when show "Warning!! Erase Linux in Flash then burn new
one. Are you sure? (Y/N)"
Input device IP (192.168.0.1) ==:192.168.0.1
Input server IP (192.168.0.180) ==:192.168.0.180
Input Linux Kernel filename () ==:firmware_name
The router should download the firmware via TFTP and complete flashing in
a few minutes.
After flashing is complete, use the PC to browse to http://192.168.1.1 or
ssh to proceed with the configuration.
Signed-off-by: Alexey Bartenev <41exey@proton.me>
The Ten64 board[1] is based around NXP's Layerscape LS1088A SoC.
It is capable of booting both standard Linux distributions
from disk devices, using EFI, and booting OpenWrt
from NAND.
See the online manual for more information, including the
flash layout[2].
This patchset adds support for generating Ten64 images
for NAND boot.
For disk boot, one can use the EFI support that was
recently added to the armvirt target.
We previously supported NAND users by building
inside our armvirt/EFI target[3], but this approach
is not suitable for OpenWrt upstream. Users who
used our supplied NAND images will be able to upgrade
to this via sysupgrade.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
[1] - https://www.traverse.com.au/hardware/ten64
[2] - https://ten64doc.traverse.com.au/hardware/flash/
[3] - Example:
285e4360e1
Device specifications:
======================
* Qualcomm/Atheros AR9344
* 128 MB of RAM
* 16 MB of SPI NOR flash
* 2x 10/100 Mbps Ethernet
* 2T2R 2.4/5 GHz Wi-Fi
* 4x GPIO-LEDs (1x wifi, 2x ethernet, 1x power)
* 1x GPIO-button (reset)
* 2x fast ethernet
- lan1
+ builtin switch port 1
+ used as WAN interface
- lan2
+ builtin switch port 2
+ used as LAN interface
* 9-30V DC
* external antennas
Flashing instructions:
======================
Log in to https://192.168.127.253/
Username: admin
Password: moxa
Open Maintenance > Firmware Upgrade and install the factory image.
Serial console access:
======================
Connect a RS232-USB converter to the maintenance port.
Pinout: (reset button left) [GND] [NC] [RX] [TX]
Firmware Recovery:
==================
When the WLAN and SYS LEDs are flashing, the device is in recovery mode.
Serial console access is required to proceed with recovery.
Download the original image from MOXA and rename it to 'awk-1137c.rom'.
Set up a TFTP server at 192.168.127.1 and connect to a lan port.
Follow the instructions on the serial console to start the recovery.
Signed-off-by: Maximilian Martin <mm@simonwunderlich.de>
This commit adds support for Mercusys MR90X(EU) v1 router.
Device specification
--------------------
SoC Type: MediaTek MT7986BLA, Cortex-A53, 64-bit
RAM: MediaTek MT7986BLA (512MB)
Flash: SPI NAND GigaDevice GD5F1GQ5UEYIGY (128 MB)
Ethernet: MediaTek MT7531AE + 2.5GbE MaxLinear GPY211C0VC (SLNW8)
Ethernet: 1x2.5Gbe (WAN/LAN 2.5Gbps), 3xGbE (WAN/LAN 1Gbps, LAN1, LAN2)
WLAN 2g: MediaTek MT7975N, b/g/n/ax, MIMO 4x4
WLAN 5g: MediaTek MT7975P(N), a/n/ac/ax, MIMO 4x4
LEDs: 1 orange and 1 green status LEDs, 4 green gpio-controlled
LEDs on ethernet ports
Button: 1 (Reset)
USB ports: No
Power: 12 VDC, 2 A
Connector: Barrel
Bootloader: Main U-Boot - U-Boot 2022.01-rc4. Additionally, both UBI
slots contain "seconduboot" (also U-Boot 2022.01-rc4)
Serial console (UART)
---------------------
V
+-------+-------+-------+-------+
| +3.3V | GND | TX | RX |
+---+---+-------+-------+-------+
|
+--- Don't connect
The R3 (TX line) and R6 (RX line) are absent on the PCB. You should
solder them or solder the jumpers.
Installation (UART)
-------------------
1. Place OpenWrt initramfs image on tftp server with IP 192.168.1.2
2. Attach UART, switch on the router and interrupt the boot process by
pressing 'Ctrl-C'
3. Load and run OpenWrt initramfs image:
tftpboot initramfs-kernel.bin
bootm
4. Once inside OpenWrt, set / update env variables:
fw_setenv baudrate 115200
fw_setenv bootargs "ubi.mtd=ubi0 console=ttyS0,115200n1 loglevel=8 earlycon=uart8250,mmio32,0x11002000 init=/etc/preinit"
fw_setenv fdtcontroladdr 5ffc0e70
fw_setenv ipaddr 192.168.1.1
fw_setenv loadaddr 0x46000000
fw_setenv mtdids "spi-nand0=spi-nand0"
fw_setenv mtdparts "spi-nand0:2M(boot),1M(u-boot-env),50M(ubi0),50M(ubi1),8M(userconfig),4M(tp_data)"
fw_setenv netmask 255.255.255.0
fw_setenv serverip 192.168.1.2
fw_setenv stderr serial@11002000
fw_setenv stdin serial@11002000
fw_setenv stdout serial@11002000
fw_setenv tp_boot_idx 0
5. Run 'sysupgrade -n' with the sysupgrade OpenWrt image
Installation (without UART)
---------------------------
1. Login as root via SSH (router IP, port 20001, password - your web
interface password)
2. Open for editing /etc/hotplug.d/iface/65-iptv (e.g., using WinSCP and
SSH settings from the p.1)
3. Add a newline after "#!/bin/sh":
telnetd -l /bin/login.sh
4. Save "65-iptv" file
5. Toggle "IPTV/VLAN Enable" checkbox in the router web interface and
save
6. Make sure that telnetd is running:
netstat -ltunp | grep 23
7. Login via telnet to router IP, port 23 (no username and password are
required)
8 Upload OpenWrt "initramfs-kernel.bin" to the "/tmp" folder of the
router (e.g., using WinSCP and SSH settings from the p.1)
9. Stock busybox doesn't contain ubiupdatevol command. Hence, we need to
download and upload the full version of busybox to the router. For
example, from here:
https://github.com/xerta555/Busybox-Binaries/raw/master/busybox-arm64
Upload busybox-arm64 to the /tmp dir of the router and run:
in the telnet shell:
cd /tmp
chmod a+x busybox-arm64
10. Check "initramfs-kernel.bin" size:
du -h initramfs-kernel.bin
11. Delete old and create new "kernel" volume with appropriate size
(greater than "initramfs-kernel.bin" size):
ubirmvol /dev/ubi0 -N kernel
ubimkvol /dev/ubi0 -n 1 -N kernel -s 9MiB
12. Write OpenWrt "initramfs-kernel.bin" to the flash:
./busybox-arm64 ubiupdatevol /dev/ubi0_1 /tmp/initramfs-kernel.bin
13. u-boot-env can be empty so lets create it (or overwrite it if it
already exists) with the necessary values:
fw_setenv baudrate 115200
fw_setenv bootargs "ubi.mtd=ubi0 console=ttyS0,115200n1 loglevel=8 earlycon=uart8250,mmio32,0x11002000 init=/etc/preinit"
fw_setenv fdtcontroladdr 5ffc0e70
fw_setenv ipaddr 192.168.1.1
fw_setenv loadaddr 0x46000000
fw_setenv mtdids "spi-nand0=spi-nand0"
fw_setenv mtdparts "spi-nand0:2M(boot),1M(u-boot-env),50M(ubi0),50M(ubi1),8M(userconfig),4M(tp_data)"
fw_setenv netmask 255.255.255.0
fw_setenv serverip 192.168.1.2
fw_setenv stderr serial@11002000
fw_setenv stdin serial@11002000
fw_setenv stdout serial@11002000
fw_setenv tp_boot_idx 0
14. Reboot to OpenWrt initramfs:
reboot
15. Login as root via SSH (IP 192.168.1.1, port 22)
16. Upload OpenWrt sysupgrade.bin image to the /tmp dir of the router
17. Run sysupgrade:
sysupgrade -n /tmp/sysupgrade.bin
Recovery
--------
1. Press Reset button and power on the router
2. Navigate to U-Boot recovery web server (http://192.168.1.1/) and
upload the OEM firmware
Recovery (UART)
---------------
1. Place OpenWrt initramfs image on tftp server with IP 192.168.1.2
2. Attach UART, switch on the router and interrupt the boot process by
pressing 'Ctrl-C'
3. Load and run OpenWrt initramfs image:
tftpboot initramfs-kernel.bin
bootm
4. Do what you need (restore partitions from a backup, install OpenWrt
etc.)
Stock layout
------------
0x000000000000-0x000000200000 : "boot"
0x000000200000-0x000000300000 : "u-boot-env"
0x000000300000-0x000003500000 : "ubi0"
0x000003500000-0x000006700000 : "ubi1"
0x000006700000-0x000006f00000 : "userconfig"
0x000006f00000-0x000007300000 : "tp_data"
ubi0/ubi1 format
----------------
U-Boot at boot checks that all volumes are in place:
+-------------------------------+
| Volume Name: uboot Vol ID: 0|
| Volume Name: kernel Vol ID: 1|
| Volume Name: rootfs Vol ID: 2|
+-------------------------------+
MAC addresses
-------------
+---------+-------------------+-----------+
| | MAC | Algorithm |
+---------+-------------------+-----------+
| label | 00:eb:xx:xx:xx:be | label |
| LAN | 00:eb:xx:xx:xx:be | label |
| WAN | 00:eb:xx:xx:xx:bf | label+1 |
| WLAN 2g | 00:eb:xx:xx:xx:be | label |
| WLAN 5g | 00:eb:xx:xx:xx:bd | label-1 |
+---------+-------------------+-----------+
label MAC address was found in UBI partition "tp_data", file
"default-mac". OEM wireless eeprom is also there (file
"MT7986_EEPROM.bin").
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Hardware
========
CPU Qualcomm Atheros QCA9558
RAM 256MB DDR2
FLASH 2x 16M SPI-NOR (Macronix MX25L12805D)
WIFI Qualcomm Atheros QCA9558
Atheros AR9590
Installation
============
1. Attach to the serial console of the AP-105.
Interrupt autoboot and change the U-Boot env.
$ setenv rb_openwrt "setenv ipaddr 192.168.1.1;
setenv serverip 192.168.1.66;
netget 0x80060000 ap115.bin; go 0x80060000"
$ setenv fb_openwrt "bank 1;
cp.b 0xbf100040 0x80060000 0x10000; go 0x80060000"
$ setenv bootcmd "run fb_openwrt"
$ saveenv
2. Load the OpenWrt initramfs image on the device using TFTP.
Place the initramfs image as "ap105.bin" in the TFTP server
root directory, connect it to the AP and make the server reachable
at 192.168.1.66/24.
$ run rb_openwrt
3. Once OpenWrt booted, transfer the sysupgrade image to the device
using scp and use sysupgrade to install the firmware.
Signed-off-by: David Bauer <mail@david-bauer.net>
Hardware
--------
SOC: MediaTek MT7986
RAM: 1024MB DDR3
FLASH: 128MB SPI-NAND (Winbond)
WIFI: Mediatek MT7986 DBDC 802.11ax 2.4/5 GHz
ETH: Realtek RTL8221B-VB-CG 2.5 N-Base-T PHY with PoE
UART: 3V3 115200 8N1 (Pinout silkscreened / Do not connect VCC)
Installation
------------
1. Download the OpenWrt initramfs image. Copy the image to a TFTP server
2. Connect the TFTP server to the WAX220. Conect to the serial console,
interrupt the autoboot process by pressing '0' when prompted.
3. Download & Boot the OpenWrt initramfs image.
$ setenv ipaddr 192.168.2.1
$ setenv serverip 192.168.2.2
$ tftpboot openwrt.bin
$ bootm
4. Wait for OpenWrt to boot. Transfer the sysupgrade image to the device
using scp and install using sysupgrade.
$ sysupgrade -n <path-to-sysupgrade.bin>
Signed-off-by: Flole Systems <flole@flole.de>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Now that qualcommax exists as a target and dependencies have been updated
let move ipq807x support to subtarget of qualcommax.
This is mostly copy/paste with the exception of having to update SSDK and
NSS-DP to use CONFIG_TARGET_SUBTARGET.
This is a preparation for later addition of IPQ60xx and IPQ50xx support.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Currently, ipq807x only covers Qualcomm IPQ807x SoC-s.
However, Qualcomm also has IPQ60xx and IPQ50xx SoC-s under the AX WiSoC-s
and they share a lot of stuff with IPQ807x, especially IPQ60xx so to avoid
duplicating kernel patches and everything lets make a common target with
per SoC subtargets.
Start doing that by renaming ipq807x to qualcommax so that dependencies
on ipq807x target can be updated.
Signed-off-by: Robert Marko <robimarko@gmail.com>
This adds support for Beeline Smart Box TURBO+ (Serсomm S3 CQR) router.
Device specification
--------------------
SoC Type: MediaTek MT7621AT (880 MHz, 2 cores)
RAM (Nanya NT5CC64M16GP): 128 MiB
Flash (Macronix MX30LF1G18AC): 128 MiB
Wireless 2.4 GHz (MT7603EN): b/g/n, 2x2
Wireless 5 GHz (MT7615N): a/n/ac, 4x4
Ethernet: 5 ports - 5×GbE (WAN, LAN1-4)
USB ports: 1xUSB3.0
Buttons: 2 button (reset, wps)
LEDs: Red, Green, Blue
Zigbee (EFR32MG1B232GG): 3.0
Stock bootloader: U-Boot 1.1.3
Power: 12 VDC, 1.5 A
Installation (fw 2.0.9)
-----------------------
1. Login to the web interface under SuperUser (root) credentials.
Password: SDXXXXXXXXXX, where SDXXXXXXXXXX is serial number of the
device written on the backplate stick.
2. Navigate to Setting -> WAN. Add:
Name - WAN1
Connection Type - Static
IP Address - 172.16.0.1
Netmask - 255.255.255.0
Save -> Apply. Set default: WAN1
3. Enable SSH and HTTP on WAN. Setting -> Remote control. Add:
Protocol - SSH
Port - 22
IP Address - 172.16.0.1
Netmask - 255.255.255.0
WAN Interface - WAN1
Save ->Apply
Add:
Protocol - HTTP
Port - 80
IP Address - 172.16.0.1
Netmask - 255.255.255.0
WAN interface - WAN1
Save -> Apply
4. Set up your PC ethernet:
Connection Type - Static
IP Address - 172.16.0.2
Netmask - 255.255.255.0
Gateway - 172.16.0.1
5. Connect PC using ethernet cable to the WAN port of the router
6. Connect to the router using SSH shell under SuperUser account
7. Make a mtd backup (optional, see related section)
8. Change bootflag to Sercomm1 and reboot:
printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3
reboot
9. Login to the router web interface under admin account
10. Remove dots from the OpenWrt factory image filename
11. Update firmware via web using OpenWrt factory image
Revert to stock
---------------
Change bootflag to Sercomm1 in OpenWrt CLI and then reboot:
printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3
mtd backup
----------
1. Set up a tftp server (e.g. tftpd64 for windows)
2. Connect to a router using SSH shell and run the following commands:
cd /tmp
for i in 0 1 2 3 4 5 6 7 8 9 10; do nanddump -f mtd$i /dev/mtd$i; \
tftp -l mtd$i -p 172.16.0.2; md5sum mtd$i >> mtd.md5; rm mtd$i; done
tftp -l mtd.md5 -p 171.16.0.2
Recovery
--------
Use sercomm-recovery tool.
Link: https://github.com/danitool/sercomm-recovery
MAC Addresses (fw 2.0.9)
------------------------
+-----+------------+---------+
| use | address | example |
+-----+------------+---------+
| LAN | label | *:e8 |
| WAN | label + 1 | *:e9 |
| 2g | label + 4 | *:ec |
| 5g | label + 5 | *:ed |
+-----+------------+---------+
The label MAC address was found in Factory 0x21000
Factory image format
--------------------
+---+-------------------+-------------+--------------------+
| # | Offset | Size | Description |
+---+-------------------+-------------+--------------------+
| 1 | 0x0 | 0x200 | Tag Header Factory |
| 2 | 0x200 | 0x100 | Tag Header Kernel1 |
| 3 | 0x300 | 0x100 | Tag Header Kernel2 |
| 4 | 0x400 | SIZE_KERNEL | Kernel |
| 5 | 0x400+SIZE_KERNEL | SIZE_ROOTFS | RootFS(UBI) |
+---+-------------------+-------------+--------------------+
Co-authored-by: Mikhail Zhilkin <csharper2005@gmail.com>
Signed-off-by: Maximilian Weinmann <x1@disroot.org>
The armvirt target has been renamed to armsr (Arm SystemReady),
so the GRUB configuration also needs to change.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
This commit add u-boot env config for GL-MT3000, so
that we can use fw_printenv to print u-boot env and
use fw_setenv to set u-boot env in GL-MT3000.
Signed-off-by: Jianhui Zhao <zhaojh329@gmail.com>
Update bootloader environment for BPi-R3 and BPi-R64 to adapt to new
device tree overlay mechanism now that support for multiple device
tree overlays has been added.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This adds a separate package for EFI on Arm SystemReady
compatible machines. 32-bit Arm UEFI is supported as well.
It is very similar to x86-64 EFI setup, without the
need for BIOS backward compatibility and slightly
different default modules.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Add support for the Xunlong Orange Pi R1 Plus LTS.
Manually generated of-platdata files to avoid swig dependency.
Tested-by: Volkan Yetik <no3iverson@gmail.com>
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Add support for the Xunlong Orange Pi R1 Plus.
Manually generated of-platdata files to avoid swig dependency.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
At this moment loadaddr in most layerscape boards are configured to
0x81000000. 5.15 kernel on some boards is bigger than 5.10 and it cause error:
Loading kernel from FIT Image at 81000000 ...
Using 'config-1' configuration
Trying 'kernel-1' kernel subimage
Description: ARM64 OpenWrt Linux-5.15.112
Created: 2023-05-21 17:39:35 UTC
Type: Kernel Image
Compression: gzip compressed
Data Start: 0x810000ec
Data Size: 7513944 Bytes = 7.2 MiB
Architecture: AArch64
OS: Linux
Load Address: 0x80000000
Entry Point: 0x80000000
Hash algo: crc32
Hash value: 6fd69550
Hash algo: sha1
Hash value: ee34c753ffb615e199a428762824ad4a0aaef90a
Verifying Hash Integrity ... crc32+ sha1+ OK
Loading fdt from FIT Image at 81000000 ...
Using 'config-1' configuration
Trying 'fdt-1' fdt subimage
Description: ARM64 OpenWrt fsl_ls1088a-rdb-sdboot device tree blob
Created: 2023-05-21 17:39:35 UTC
Type: Flat Device Tree
Compression: uncompressed
Data Start: 0x8172a98c
Data Size: 19794 Bytes = 19.3 KiB
Architecture: AArch64
Hash algo: crc32
Hash value: 59792ba3
Hash algo: sha1
Hash value: 135585a49f86cd85acea559b78b0098ae99d5e12
Verifying Hash Integrity ... crc32+ sha1+ OK
Booting using the fdt blob at 0x8172a98c
Uncompressing Kernel Image
ERROR: new format image overwritten - must RESET the board to recover
resetting ...
This patch changes loadaddr to 0x88000000 (like LS1012A-FRDM board) to
avoid overlapping for bigger images (like initramfs) too.
Tested-by: Alexandra Alth <alexandra@alth.de> [LS1088ARDB]
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Add new package for building bootloader for the SiFive U-series boards. Supported
boards at this stage are the HiFive Unleashed and HiFive Unmatched.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
OpenSBI is a form of a first-stage bootloader, which initializes
certain parts of an SoC and then passes on control to the second
stage bootloader i.e. an u-boot image.
We're introducing the package with release v1.2, which provides
SBI v0.3 and the SBI SRST extensions which helps to gracefully
reboot/shutdown various HiFive-U SoCs.
Tested on SiFive Unleashed and Unmatched boards.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Add new build option BOARD_QFN/BOARD_BGA.
This option is only useful for MT7981 device.
MT7981A/B: BOARD_BGA, MT7981C: BOARD_QFN.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Add reserved memory for pstore/ramoops to device tree used by Linux
as well as U-Boot.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The Compex WPQ873 is a development board with two M.2 B-key
slots for cellular modems.
Device info:
- IPQ8072A SoC
- 512MiB RAM
- 256MiB NAND flash
- 8MiB SPI NOR
- 3x 1GigE ports
- 1x 2.5GigE port
- 2.4GHz/5GHz AX WLAN
- 1x USB 3.0 port
- 1x M.2 B-key socket with PCIe 3.0
- 1x M.2 B-key socket with PCIe 2.0 and USB 3.0
- 4x SIM card slots
- Bluetooth LE 5.0 (QCA4024)
Prerequisites
1) TFTP server
2) 3.3V USB to TTL cable for UART console
2.54mm pitch 4-pin header for UART is readily provided on board, no modifications are necessary to access it
TTL connector pinout: 2=TX, 3=RX, 4=GND
Arrow marks pin 1 which is 3.3V
Serial port settings: 115200 8N1 no flow control
The device will most likely ship with a QSDK-based firmware.
1. Power on device and interrupt u-boot to obtain u-boot CLI
2. set serverip to IP address of the TFTP server, for example:
`setenv serverip 192.168.1.10`
3. Download image from TFTP server:
`tftpboot 0x44000000 openwrt-ipq807x-generic-compex_wpq873-squashfs-factory.ubi`
4. Flash ubi image to both partitions and reset:
`sf probe
imxtract 0x44000000 ubi
nand device 0
nand erase 0x0 0x3400000
nand erase 0x3c00000 0x3400000
nand write $fileaddr 0x0 $filesize
nand write $fileaddr 0x3c00000 $filesize
reset`
Afterwards, you can use sysupgrade to flash new OpenWRT images.
Signed-off-by: Antti Nykänen <antti.nykanen@nokia.com>
Zyxel EX5601-T0 specifics
--------------
The operator specific firmware running on the Zyxel branded
EX5601-T0 includes U-Boot modifications affecting the OpenWrt
installation.
Partition Table
| dev | size | erasesize | name |
| ---- | -------- | --------- | ------------- |
| mtd0 | 20000000 | 00040000 | "spi0.1" |
| mtd1 | 00100000 | 00040000 | "BL2" |
| mtd2 | 00080000 | 00040000 | "u-boot-env" |
| mtd3 | 00200000 | 00040000 | "Factory" |
| mtd4 | 001c0000 | 00040000 | "FIP" |
| mtd5 | 00040000 | 00040000 | "zloader" |
| mtd6 | 04000000 | 00040000 | "ubi" |
| mtd7 | 04000000 | 00040000 | "ubi2" |
| mtd8 | 15a80000 | 00040000 | "zyubi" |
The router boots BL2 which than loads FIP (u-boot).
U-boot has hardcoded a command to always launch Zloader "mtd read zloader 0x46000000" and than "bootm". Bootargs are deactivated.
Zloader is the zyxel booloader which allow to dual-boot ubi or ubi2, by default access to zloader is blocked.
Too zloader checks that the firmware contains a particolar file called zyfwinfo.
Additional details regarding Zloader can be found here:
https://hack-gpon.github.io/zyxel/https://forum.openwrt.org/t/adding-openwrt-support-for-zyxel-ex5601-t0/155914
Hardware
--------
SOC: MediaTek MT7986a
CPU: 4 core cortex-a53 (2000MHz)
RAM: 1GB DDR4
FLASH: 512MB SPI-NAND (Micron xxx)
WIFI: Wifi6 Mediatek MT7976 802.11ax 5 GHz 4x4 + 2.4GHZ 4x4
ETH: MediaTek MT7531 Switch + SoC
3 x builtin 1G phy (lan1, lan2, lan3)
1 x MaxLinear GPY211B 2.5 N-Base-T phy5 (lan4)
1 x MaxLinear GPY211B 2.5Gbit xor SFP/N-Base-T phy6 (wan)
USB: 1 x USB 3.2 Enhanced SuperSpeed port
UART: 3V3 115200 8N1 (Pinout: GND KEY RX TX VCC)
VOIP: 2 FXS ports for analog phones
MAC Address Table
-----------------
eth0/lan Factory 0x002a
eth1/wan Factory 0x0024
wifi 2.4Ghz Factory 0x0004
wifi 5Ghz Factory 0x0004 + 1
Serial console (UART)
---------------------
+-------+-------+-------+-------+-------+
| +3.3V | RX | TX | KEY | GND |
+---+---+-------+-------+-------+-------+
|
+--- Don't connect
Installation
------------
Keep in mind that openwrt can only run on the UBI partition, the openwrt firmware is not able to understand the zloader bootargs.
The procedure allows restoring the UBI partition with the Zyxel firmware and retains all the OEM functionalities.
1. Unlock Zloader (this will allow to swap manually between partitions UBI and UBI2):
- Attach a usb-ttl adapter to your computer and boot the router.
- While the router is booting at some point you will read the following: `Please press Enter to activate this console.`
- As soon as you read that press enter, type root and than press enter again (just do it, don't care about the logs scrolling).
- Most likely the router is still printing the boot log, leave it boot until it stops.
- If everything went ok you should have full root access "root@EX5601-T0:/#".
- Type the following command and press enter: "fw_setenv EngDebugFlag 0x1".
- Reboot the router.
- As soon as you read `Hit any key to stop autoboot:` press Enter.
- If everything went ok you should have the following prompt: "ZHAL>".
- You have successfully unlocked zloader access, this procedure must be done only once.
2. Check the current active partition:
- Boot the router and repeat the steps above to gain root access.
- Type the following command to check the current active image: "cat /proc/cmdline".
- If `rootubi=ubi` it means that the active partition is `mtd6`
- If `rootubi=ubi2` it means that the active partition is `mtd7`
- As mentioned earlier we need to flash openwrt into ubi/mtd6 and never overwrite ubi2/mtd7 to be able to fully roll-back.
- To activate and boot from mtd7 (ubi2) enter into ZHAL> command prompt and type the following commands:
atbt 1 # unlock write
atsw # swap boot partition
atsr # reboot the router
- After rebooting check again with "cat /proc/cmdline" that you are correctly booting from mtd7/ubi2
- If yes proceed with the installation guide. If not probably you don't have a firmware into ubi2 or you did something wrong.
3. Flashing:
- Download the sysupgrade file for the router from openwrt, than we need to add the zyfwinfo file into the sysupgrade tar.
Zloader only checks for the magic (which is a fixed value 'EXYZ') and the crc of the file itself (256bytes).
I created a script to create a valid zyfwinfo file but you can use anything that does exactly the same:
https://raw.githubusercontent.com/pameruoso/OpenWRT-Zyxel-EX5601-T0/main/gen_zyfwinfo.sh
- Add the zyfwinfo file into the sysupgrade tar.
- Enter via telnet or ssh into the router with admin credentials
- Enter the following commands to disable the firmware and model checks
"zycli fwidcheck off" and "zycli modelcheck off"
- Open the router web interface and in the update firmware page select the "restore default settings option"
- Select the sysupgrade file and click on upload.
- The router will flash and reboot itself into openwrt from UBI
4. Restoring and going back to Zyxel firmware.
- Use the ZHAL> command line to manually swap the boot parition to UBI2 with the following:
atbt 1 # unlock write
atsw # swap boot partition
atsr # reboot the router
- You will boot again the Zyxel firmware you have into UBI2 and you can flash the zyxel firmware to overwrite the UBI partition and openwrt.
Working features
----------------
3 gbit lan ports
Wifi
Zyxel partitioning for coexistance with Zloader and dual boot.
WAN SFP port (only after exporting pins 57 and 10. gpiobase411)
leds
reset button
serial interface
usb port
lan ethernet 2.5 gbit port (autosense)
wan ethernet 2.5 gbit port (autosense)
Not working
----------------
voip (missing drivers or proper zyxel platform software)
Swapping the wan ethernet/sfp xor port
----------------
The way to swap the wan port between sfp and ethernet is the following:
export the pins 57 and 10.
Pin 57 is used to probe if an sfp is present.
If pin 57 value is 0 it means that an sfp is present into the cage (cat /sys/class/gpio/gpio468/value).
If pin 57 value is 1 it means that no sfp is inserted into the cage.
In conclusion by default both 57 an 10 pins are by default 1, which means that the active port is the ethernet one.
After inserting an SFP pin 57 will become 0 and you have to manually change the value of pin 10 to 0 too.
This is totally scriptable of course.
Leds description
------------
All the leds are working out of the box but the leds managed by the 2 maxlinear phy (phy 5 lan, phy6 wan).
To activate the phy5 led (rj45 ethernet port led on the back of the router) you have to use mdio-tools.
To activate the phy6 led (led on the front of the router for 2.5gbit link) you have to use mdio-tools.
Example:
Set lan5 led to fast blink on 2500/1000, slow blink on 10/100:
mdio mdio-bus mmd 5:30 raw 0x0001 0x33FC
Set wan 2.5gbit led to constant on when wan is 2.5gbit:
mdio mdio-bus mmd 6:30 raw 0x0001 0x0080
Signed-off-by: Pietro Ameruoso <p.ameruoso@live.it>
Specifications:
SOC: QCA9563 775 MHz + QCA9880
Switch: QCA8337N-AL3C
RAM: Winbond W9751G6KB-25 64 MiB
Flash: Winbond W25Q128FVSG 16 MiB
WLAN: Wi-Fi4 2.4 GHz 3*3 + 5 GHz 3*3
LAN: LAN ports *4
WAN: WAN port *1
Buttons: reset *1 + wps *1
LEDs: ethernet *5, power, wlan, wps
MAC Address:
use address source1 source2
label 40:9b:xx:xx:xx:3c lan && wlan u-boot,env@ethaddr
lan 40:9b:xx:xx:xx:3c devdata@0x3f $label
wan 40:9b:xx:xx:xx:3f devdata@0x8f $label + 3
wlan2g 40:9b:xx:xx:xx:3c devdata@0x5b $label
wlan5g 40:9b:xx:xx:xx:3e devdata@0x76 $label + 2
Install via Web UI:
Apply factory image in the stock firmware's Web UI.
Install via Emergency Room Mode:
DIR-859 A1 will enter recovery mode when the system fails to boot
or press reset button for about 10 seconds.
First, set computer IP to 192.168.0.5 and Gateway to 192.168.0.1.
Then we can open http://192.168.0.1 in the web browser to upload
OpenWrt factory image or stock firmware. Some modern browsers may
need to turn on compatibility mode.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
1. Remove unnecessary new lines in the dts.
2. Remove duplicate included file "gpio.h" in the device dts.
3. Add missing button labels "reset" and "wps".
4. Unify the format of the reg properties.
5. Add u-boot environment support.
6. Reduce spi clock frequency since the max value suggested by the
chip datasheet is only 25 MHz.
7. Add seama header fixup for DIR-859 A1. Without this header fixup,
u-boot checksum for kernel will fail after the first boot.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
A missing '\' caused the remaining parameters not to be passed to make.
This fixes the following error:
| gcc -c [...] fiptool.c -o fiptool.o
| In file included from fiptool.h:16,
| from fiptool.c:19:
|fiptool_platform.h:19:11: fatal error: openssl/sha.h: No such file or directory
| 19 | # include <openssl/sha.h>
| | ^~~~~~~~~~~~~~~
|compilation terminated.
|make[3]: *** [Makefile:58: fiptool.o] Error 1
as the HOST_CFLAGS are no longer passed.
then, HOST_CFLAGS is specified as a command argument, this
is a specific problem of our built since appending these
needs the override directive.
Fixes: df28bfe03247 ("tfa-layerscape: Change to github and use the latest tag")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The default location of tfa-layerscape has been changed from
codeuaurora to github. Also use the latest tag for Layerscape
Linux Development POC from NXP.
v2:
* restored ls1021a-afrdm board
* added platform defines to fiptool so ls-ddr-phy can be built
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@protonmail.ch>
(reset PKG_RELEASE)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The default location of uboot-layerscape has been changed
from codeuaurora to github. Also use the latest tag for
Layerscape Linux Development POC from NXP.
Tested on:
* NXP FRWY-LS1012A
* NXP LS1028A-RDB
* NXP LS1046A-RDB
V2: Remove ls1028ardb specifix fixups not needed with new uboot
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@protonmail.ch>
(reset PKG_RELEASE)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Add support for the FriendlyARM NanoPi R2C.
Manually generated of-platdata files to avoid swig dependency.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Instead of adding these common variables again and again simply create a
shared set for each SoC.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Based on Paul Fertser <fercerpav@gmail.com>'s guidance:
Change AUTORELEASE in rules.mk to:
```
AUTORELEASE = $(if $(DUMP),0,$(shell sed -i "s/\$$(AUTORELEASE)/$(call commitcount,1)/" $(CURDIR)/Makefile))
```
then update all affected packages by:
```
for i in $(git grep -l PKG_RELEASE:=.*AUTORELEASE | sed 's^.*/\([^/]*\)/Makefile^\1^';);
do
make package/$i/clean
done
```
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Hardware specification:
- SoC: MediaTek MT7621AT (880 MHz)
- Flash: 16 MB (Macronix MX25L12835FM2I-10G)
- RAM: 128 MB (Nanya NT5CC64M16GP-DI)
- WLAN 2.4 GHz: 2x2 MediaTek MT7603EN
- WLAN 5 GHz: 2x2 MediaTek MT7615N
- Ethernet: 1x 10/100/1000 Mbps
- LED: Power, Wifi, WPS
- Button: Reset, WPS
- UART: 1:VCC, 2:GND, 3:TX, 4:RX (from LAN port)
Serial console @ 57600,8n1
Flash instructions:
Connect to serial console and start up the device. As the bootloader got
locked you need to type in a password to unlock U-Boot access.
When you see the following output on the console:
relocate_code Pointer at: 87f1c000
type in the super secure password:
1234567890
Then select TFTP boot from RAM by selecting option 1 in the boot menu.
As Linksys decided to leave out a basic TFTP configuration you need to
set server- & client ip as well as the image filename the device will
search for. You need to use the initramfs openwrt image for the TFTP
boot process.
Once openwrt has booted up, upload the sysupgrade image via scp and run
sysupgrade as normal.
Signed-off-by: Christoph Krapp <achterin@gmail.com>
Add support for the Firefly ROC-RK3328-CC.
Manually generated of-platdata files to avoid swig dependency.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Support uboot for NXP LS1028ARDB reference board. GIC V3 has to
be disabled in the uboot config to allow booting upstream kernels.
This patch can be dropped once uboot is updated to 2022.04 version
to nxp-qoriq github lf-6.1.1 branch.
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@protonmail.ch>
There seems to be a difference in firmware calling convention
between upstream and NXP kernels. On some cpus like ls1028
it will hang on firmware secure get random when using LF uboot
with upstream kernel. Instead of commenting it out, don't call
get radnom seed when "kaslr-seed" is not present in device tree.
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@protonmail.ch>
The image_header_t typedef has been removed from
uboot v2023.01 [1], replaced with legacy struct.
[1] f3543e6944
Fixes: 3d5c542 ("uboot-mediatek: update to U-Boot 2023.01")
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
CONFIG_SYS_TEXT_BASE has been renamed to CONFIG_TEXT_BASE
in uboot v2023.01 [1], fixes all this variable.
[1] 984639039f
Fixes: 3d5c5427 ("uboot-mediatek: update to U-Boot 2023.01")
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
The ZyXEL WSM20 aka Multy M1 is a cheap mesh router system by ZyXEL
based on the MT7621 CPU.
Specifications
==============
SoC: MediaTek MT7621AT (880MHz)
RAM: 256MiB
Flash: 128MiB NAND
Wireless: 802.11ax (2x2 MT7915E DBDC)
Ethernet: 4x 10/100/1000 (MT7530)
Button: 1x WPS, 1x Reset, 1x LED On/Off
LED: 7 LEDs (3x white, 2x red, 2x green)
MAC address assignment
======================
The MAC address assignment follows stock: The label MAC address is the LAN
MAC address, the WAN address is read from flash.
The WiFi MAC addresses are set in userspace to label MAC + 1 and label MAC
+ 2.
Installation (web interface)
============================
The device is cloud-managed, but there is a hidden local firmware upgrade
page in the OEM web interface. The device has to be registered in the
cloud in order to be able to access this page.
The system has a dual firmware design, there is no way to tell which
firmware is currently booted. Therefore, an -initramfs version is flashed
first.
1. Log into the OEM web GUI
2. Access the hidden upgrade page by navigating to
https://192.168.212.1/gui/#/main/debug/firmwareupgrade
3. Upload the -initramfs-kernel.bin file and flash it
4. Wait for OpenWrt to boot and log in via SSH
5. Transfer the sysupgrade file via SCP
6. Run sysupgrade to install the image
7. Reboot and enjoy
NB: If the initramfs version was installed in RAS2, the sysupgrade script
sets the boot number to the first partition. A backup has to be performed
manually in case the OEM firwmare should be kept.
Installation (UART method)
==========================
The UART method is more difficult, as the boot loader does not have a
timeout set. A semi-working stock firmware is required to configure it:
1. Attach UART
2. Boot the stock firmware until the message about failsafe mode appears
3. Enter failsafe mode by pressing "f" and "Enter"
4. Type "mount_root"
5. Run "fw_setenv bootmenu_delay 3"
6. Reboot, U-Boot now presents a menu
7. The -initramfs-kernel.bin image can be flashed using the menu
8. Run the regular sysupgrade for a permanent installation
Changing the partition to boot is a bit cumbersome in U-Boot, as there is
no menu to select it. It can only be checked using mstc_bootnum. To change
it, issue the following commands in U-Boot:
nand read 1800000 53c0000 800
mw.b 1800004 1 1
nand erase 53c0000 800
nand write 1800000 53c0000 800
This selects FW1. Replace "mw.b 1800004 1 1" by "mw.b 1800004 2 1" to
change to the second slot.
Back to stock
=============
It is possible to flash back to stock, but a OEM firmware upgrade is
required. ZyXEL does not provide the link on its website, but the link
can be acquired from the OEM web GUI by analyzing the transferred JSON
objects.
It is then a matter of writing the firmware to Kernel2 and setting the
boot partition to FW2:
mtd write zyxel.bin Kernel2
echo -ne "\x02" | dd of=/dev/mtdblock7 count=1 bs=1 seek=4 conv=notrunc
Signed-off-by: Andreas Böhler <dev@aboehler.at>
Credits to forum users Annick and SirLouen for their initial work on this
device
The Alcatel HH40V is a CAT4 LTE router used by various ISPs.
Specifications
==============
SoC: QCA9531 650MHz
RAM: 128MiB
Flash: 32MiB SPI NOR
LAN: 1x 10/100MBit
WAN: 1x 10/100MBit
LTE: MDM9607 USB 2.0 (rndis configuration)
WiFi: 802.11n (SoC integrated)
MAC address assignment
======================
There are three MAC addresses stored in the flash ROM, the assignment
follows stock. The MAC on the label is the WiFi MAC address.
Installation (TFTP)
===================
1. Connect serial console
2. Configure static IP to 192.168.1.112
3. Put OpenWrt factory.bin file as firmware-system.bin
4. Press Power + WPS and plug in power
5. Keep buttons pressed until TFTP requests are visible
6. Wait for the system to finish flashing and wait for reboot
7. Bootup will fail as the kernel offset is wrong
8. Run "setenv bootcmd bootm 0x9f150000"
9. Reset board and enjoy OpenWrt
Installation (without UART)
===========================
Installation without UART is a bit tricky and requires several steps too
long for the commit message. Basic steps:
1. Create configure backup
2. Patch backup file to enable SSH
3. Login via SSH and configure the new bootcmd
3. Flash OpenWrt factory.bin image manually (sysupgrade doesn't work)
More detailed instructions will be provided on the Wiki page.
Tested by: Christian Heuff <christian@heuff.at>
Signed-off-by: Andreas Böhler <dev@aboehler.at>
TP-Link TL-XDR608x comes with locked vendor loader. Add U-Boot build
for replacement loader for both TL-XDR6086 and TL-XDR6088. The only
difference at U-Boot level is the different filename requested via
TFTP, matching the corresponding OpenWrt build artifacts for each
device.
The TP-Link TL-XDR4288 has the same hardware as the TP-Link TL-XDR6088
except for the wireless part. Also create a uboot for the TP-Link
TL-XDR4288.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
[rebase to uboot 23.04, correct led and button]
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
