This patch adds support for the MikroTik RouterBOARD mAP lite
https://routerboard.com/RBmAPL-2nD
Specifications:
- SoC: Qualcomm QCA9533 (650MHz)
- RAM: 64MB
- Storage: 16MB NOR SPI flash
- Wireless: builtin QCA9533, 2x2:2
- Ethernet: 1x100M
This is another 16M SPI NOR mikrotik device. The machine file is named
mach-rbspi.c because I plan to add support for several of the other spi-based
RouterBOARD devices in subsequent patches: they share most of the hardware
and thus the same codebase.
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
Add support for the EBR-2310, which is almost identical to the DIR-615
rev E4, without the wifi.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
TP-Link TL-WA850RE v2 is a wall-plug N300 Wi-Fi range extender,
based on Qualcomm/Atheros QCA9533 v2.
Short specification:
- 550/391/195 MHz (CPU/DDR/AHB)
- 1x 10/100 Mbps Ethernet
- 32 MB of RAM (DDR1)
- 4 MB of FLASH
- 2T2R 2.4 GHz
- 2x internal antennas (embedded on PCB)
- 9x LED (all can be turned off with GPIO15), 2x button
- UART (J3) header on PCB
Flash instruction: use "factory" image directly in vendor GUI.
Warning: this device does not include any kind of recovery mechanism
in the bootloader and disassembling process is not trivial.
You can access vendor firmware over serial line using:
- login: root
- password: sohoadmin
Image was tested only in US version of the device, but should work
also with the same device version sold in other countries.
Available FLASH space, with LEDE trunk, is only 240 KB.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
After "73d923e base-files: emit tagged switch configuration by default"
some default network configurations are broken because the lan and wan
ifnames are forcibly set to untagged netdevs.
Adjust the offending set_interfaces_lan_wan() calls to use the proper
tagged device names.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
TP-Link Archer C59v1 is a dual-band AC1350 router, based on Qualcomm/Atheros
QCA9561+QCA9886.
Specification:
- 775/650/258 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 2T2R 5 GHz
- 5x 10/100 Mbps Ethernet
- USB 2.0 port
- 8x LED (controled by 74HC595), 3x button
- UART header on PCB
TP-Link Archer C60v1 is a dual-band AC1350 router, based on Qualcomm/Atheros
QCA9561+QCA9886.
Specification:
- 775/650/258 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 2T2R 5 GHz
- 5x 10/100 Mbps Ethernet
- 7x LED, 2x button
- UART header on PCB
Currently not working:
- Port LAN1 on C59, LAN4 on C60
- WiFi 5GHz (missing ath10k firmware for QCA9886 chip)
- Update from oficial web interface ( tplink-saveloader not support "product-info")
Flash instruction:
1. Set PC to fixed ip address 192.168.0.66
2. Download lede-ar71xx-generic-archer-cXX-v1-squashfs-factory.bin
and rename it to tp_recovery.bin
3. Start a tftp server with the file tp_recovery.bin in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
the firmware should be transferred from the tftp server
8. Wait ~30 second to complete recovery.
Flash instruction under U-Boot, using UART:
1. tftp 0x81000000 lede-ar71xx-...-sysupgrade.bin
2. erase 0x9f020000 +$filesize
3. cp.b $fileaddr 0x9f020000 $filesize
4. reset
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
[Jo-Philipp Wich: remove duplicate ATH79_MACH_ARCHER_C59/C60_V1 entries]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Support Abicom International Scorpion SC450 Board
QCA9550 700MHz Extended Temperature Range
256MB DDR2
256MB NAND Flash
16MB NOR Flash
10/100/1000 Ethernet
15W Max, 3x3 Mode, Full Power TX Power
802.3-at POE+ & DC Input options
100x 85mm
USB
PCIe
SFP
GPIO/LED
Signed-off-by: Conor O'Gorman <i@conorogorman.net>
Support Abicom International Scorpion SC300M Module
QCA9550 700MHz Extended Temperature Range
256MB DDR2
256MB Nand Flash
16MB SPI Flash
802.11a/na/b/g/ng
GPIO x 22, USB x2, PCIe x2
10/100/1000 Ethernet
23dBm, Optional Onboard Antenna
DC Input, 8-20V DC
85 x 55 mm
Signed-off-by: Conor O'Gorman <i@conorogorman.net>
Mikrotik RB411U has only one ethernet port - eth0. This patch allows to create
correct config with one lan section.
Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
Add full support for Mikrotik RB-941-2nD (hAP lite)
Original patch by Sergey Sergeev <adron@yapic.net> and
more information is available here:
https://wiki.openwrt.org/toh/mikrotik/rb941_2nd
I updated and adapted the patch to apply cleanly to LEDE trunk
and added proper numbering for the switch ports (matching case
labels).
Tested working on actual hardware with the information
provided in the above webpage. Sysupgrade works.
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
There's a GPIO that can switch between power to USB pins for the
internal MiniPCIe slot or the external USB port.
People are more likely to use the external one so enable it by default.
Existing configurations should be unaffected
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add full support for TP-Link RE450.
The wireless SoC is similiar to Archer C7: QCA9558 + QCA9880 (pci).
The ethernet interface is AR8035, but the mdio is connected to the gpio and
the chipset builtin mdio bus isn't used, which is unique (and weird), so the
kernel gpio mdio module is used.
The two ethernet leds are connected to the GPIO, so they are both configured,
one to indicate link status and the other to indicate data transfer.
The generation of the image was added to the image Makefile.
The return value of tplink-safeloader is not ignored anymore (to fail on error)
The result factory image is flashable from the stock web ui.
Signed-off-by: Tal Keren <kooolk@gmail.com>
[rd@radekdostal.com: ar71xx: RE450: do not build RE450 for nand]
Signed-off-by: Radek Dostál <rd@radekdostal.com>
[hyniu@o2.pl: ar71xx: RE450: Renaming LED accordance with the standard]
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
[jo@mein.io: squash fixes from Radek and Henryk into original commit]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The TL-WR842N v2 has the following switch port layout with swconfig port 0
being connected to eth1:
Power LAN4 LAN3 LAN2 LAN1 WAN USB
(*) | [...] | [...] | [...] | [...] | [...] | [.]
swconfig port: 1 4 3 2 n/a
netdev: eth1 eth1 eth1 eth1 eth0
Adjust the board defaults to match this model specific layout.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This board is very old and unlikely to still be relevant today. Support
for it contains a significant amount of device specific baggage which is
worth getting rid of.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
YunCore SR3200 is a dual-band AC1200 router, based on Qualcomm/Atheros
QCA9563+QCA9882+QCA8337N.
YunCore XD3200 (FCC ID: 2ADUG-XD3200) is a dual-band AC1200 ceiling mount
AP with PoE support, based on Qualcomm/Atheros QCA9563+QCA9882+QCA8334.
Common specification:
- 775/650/258 MHz (CPU/DDR/AHB)
- 128 MB or RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 2T2R 2.4 GHz, with ext. PA (SKY65174-21), up to 30 dBm
- 2T2R 5 GHz, with ext. PA (SKY85405-11) and LNA (SKY85601-11), up to 30 dBm
SR3200 specification:
- 5x 10/100/1000 Mbps Ethernet
- 6x ext. RP-SMA antennas (actually, only 4 are connected with radio chips)
- 3x LED (+ 5x LED in RJ45 sockets), 1x button
- UART header on PCB
XD3200 specification:
- 2x 10/100/1000 Mbps Ethernet, with 802.3at PoE support (WAN port)
- 4x internal antennas
- 3 sets of LEDs on external PCB (+ 2x LED near RJ45 sockets), 1x button
- UART and JTAG (custom 6-pin, 2 mm pitch) headers on PCB
LED for 5 GHz WLAN is currently not supported on both devices as it is
connected directly to the QCA9882 radio chip.
Flash instruction under vendor firmware, using telnet/SSH:
1. If your firmware does not have root password, go to point 5
2. Connect PC with 192.168.1.x address to LAN or WAN port
3. Power up device, enter failsafe mode with button (no LED indicator!)
4. Change root password and reboot (mount_root, passwd ..., reboot -f)
5. Upload lede-ar71xx-...-sysupgrade.bin to /tmp using SCP
6. Connect PC with 192.168.188.x address to LAN port, SSH to 192.168.188.253
7. Invoke:
- cd /tmp
- fw_setenv bootcmd "bootm 0x9fe80000 || bootm 0x9f050000"
- mtd -e firmware -r write lede-ar71xx-...-sysupgrade.bin firmware
Flash instruction under U-Boot, using UART:
1. tftp 0x80060000 lede-ar71xx-...-sysupgrade.bin
2. erase 0x9f050000 +$filesize
3. cp.b $fileaddr 0x9f050000 $filesize
4. setenv bootcmd "bootm 0x9fe80000 || bootm 0x9f050000"
5. saveenv && reset
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
This patch fixes the ethernet switch initial config for Mikrotik RB450 and RB450G.
The previous version wrongly changed the RouterStation Pro config. This one creates a specific config for the RB450G and leaves the RouterStation Pro unchanged.
Signed-off-by: João Chaínho <joaochainho@gmail.com>
CPE830 is a clone of AP90Q, with different type of antenna (panel)
and additional 4 LEDs for WiFi signal level indication.
Use the same flash approach as for YunCore AP90Q.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
YunCore AP90Q is an outdoor CPE/AP based on Qualcomm/Atheros QCA9531 v2.
Short specification:
- 650/600/216 MHz (CPU/DDR/AHB)
- 2x 10/100 Mbps Ethernet, passive PoE support
- 64/128 MB of RAM (DDR2)
- 16 MB of FLASH
- 2T2R 2.4 GHz with external PA, up to 29 dBm
- 2x internal 5 dBi omni antennas
- 4x LED, 1x button
- UART (JP1) header on PCB
Flash instruction under U-Boot, using UART:
1. tftp 0x80060000 lede-ar71xx-generic-ap90q-squashfs-sysupgrade
2. erase 0x9f050000 +$filesize
3. cp.b $fileaddr 0x9f050000 $filesize
4. setenv bootcmd "bootm 0x9f050000"
5. saveenv && reset
Flash instruction under vendor fimrware, using telnet/SSH:
1. Connect PC with 192.168.1.x address to WAN port
2. Power up device, enter failsafe mode with button (no LED indicator!)
3. Change root password and reboot (mount_root, passwd ..., reboot -f)
4. Upload lede-ar71xx-generic-ap90q-squashfs-sysupgrade.bin to /tmp using SCP
5. Connect PC with 192.168.188.x address to LAN port, SSH to 192.168.188.253
6. Invoke:
- cd /tmp
- fw_setenv bootcmd "bootm 0x9f050000"
- mtd erase firmware
- mtd -r write lede-ar71xx-generic-ap90q-squashfs-sysupgrade.bin firmware
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
COMFAST CF-E380AC v1/v2 is a ceiling mount AP with PoE
support, based on Qualcomm/Atheros QCA9558+QCA9880+AR8035.
There are two versions of this model, with different RAM
and U-Boot mtd partition sizes:
- v1: 128 MB of RAM, 128 KB U-Boot image size
- v2: 256 MB of RAM, 256 KB U-Boot image size
Version number is available only inside vendor GUI,
hardware and markings are the same.
Short specification:
- 720/600/200 MHz (CPU/DDR/AHB)
- 1x 10/100/1000 Mbps Ethernet, with PoE support
- 128 or 256 MB of RAM (DDR2)
- 16 MB of FLASH
- 3T3R 2.4 GHz, with external PA (SE2576L), up to 28 dBm
- 3T3R 5 GHz, with external PA (SE5003L1), up to 30 dBm
- 6x internal antennas
- 1x RGB LED, 1x button
- UART (T11), LEDs/GPIO (J7) and USB (T12) headers on PCB
- external watchdog (Pericon Technology PT7A7514)
Flash instruction:
Original firmware is based on OpenWrt.
Use sysupgrade image directly in vendor GUI.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
As we already have support for CF-E316N v2 and many devices from
this vendor look similar, the support was included in existing
mach-*.c file, with few cleanups and fixes.
All 3 devices are based on Qualcomm/Atheros QCA9531 v2.
COMFAST CF-E320N v2 is a ceiling mount AP with PoE support.
Short specification:
- 650/393/216 MHz (CPU/DDR/AHB)
- 2x 10/100 Mbps Ethernet, both with PoE support
- 64 MB of RAM (DDR2)
- 16 MB of FLASH
- 2T2R 2.4 GHz, up to 22 dBm
- 2x internal antennas
- 1x RGB LED, 1x button
- UART (J1), GPIO (J9) and USB (J2) headers on PCB
- external watchdog (Pericon Technology PT7A7514)
COMFAST CF-E520N/CF-E530N are in-wall APs with USB and PoE support.
They seem to have different only the front panel.
Short specification:
- 650/393/216 MHz (CPU/DDR/AHB)
- 2x 10/100 Mbps Ethernet, WAN with PoE support
- 1x USB 2.0 (in CF-E520N covered by panel, available on PCB)
- 32 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz, up to 22 dBm
- 2x internal antennas
- 1x LED, 1x button
- UART (J1) headers on PCB
Flash instruction:
Original firmware is based on OpenWrt.
Use sysupgrade image directly in vendor GUI.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
OpenMesh devices have often LEDs which are not yet used by OpenWrt. These
should still be available as disabled LEDs in the system configuration for
easier modification.
Signed-off-by: Jaylin Yu <jaylin.yu@open-mesh.com>
[sven.eckelmann@open-mesh.com: Remove LEDs already specified via diag.sh,
add wifi/status LEDs]
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
Polling every 40ms causes more than 10% CPU load on weak devices. An
interval of 200ms is much more reasonable.
Signed-off-by: Martin Weinelt <martin@darmstadt.freifunk.net>
[Matthias Schiffer: adapt OpenWrt patch; add ramips; extend commit message]
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Both the MR12 and MR16 are single gigabit ethernet devices, similar to the
MR18. This change gives them the correct network config on a fresh install.
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
[Jo-Philipp Wich: adjust for alphabetical ordering, line wrap commit msg]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This patch adds support solely for version 1 of the TP-Link WR802N.
It is based on Rick Pannen's patch posted on the OpenWrt devel list.
Signed-off-by: Julius Schulz-Zander <julius@inet.tu-berlin.de>
These boards do not have a switch, so they should have never been added
to this file in the first place.
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
This patch adds support for the Airtight C-60.
SOC: Atheros AR9344 rev 2 (CPU:560.000MHz)
RAM: 128 MiB
NOR: MX25L3205D 4MiB
NAND: ST Micro NAND 32MiB 3,3V 8-bit
SW-NET: AR8327N (2 Ports)
WLAN1: Dual-Band AR9340 Rev:2 (built-in SoC)
WLAN2: Dual-Band AR9300 Rev:4 PCIe Chip
The switch is setup for an accesspoint:
LAN1: (gigabit) is the wan-port.
LAN2: (fast ethernet) is bridged with the br-lan.
Flashing Guide (via initramfs):
1. Connect a PC to the serial port of the C-60.
power up the C-60.
Enter u-boot command prompt:
#> nand erase
#> setenv bootcmd "bootm 0x9f060000"
#> saveenv
#> setenv ipaddr 192.168.1.1
#> setenv netmask 255.255.255.0
#> setenv serverip 192.168.1.100
#> setenv bootfile lede-ar71xx-nand-c-60-initramfs-kernel.bin
#> tftpboot
#> bootm
2. Wait for the C-60 to boot LEDE.
On the root prompt. Enter:
# ubiformat /dev/mtd4
# ubiattach -p /dev/mtd4
3. After that copy the sysupgrade.tar onto the router and run:
# sysupgrade sysupgrade.tar
to flash the image.
Special thanks to Chris Blake <chrisrblake93@gmail.com>. He provided
a C-60 unit and he helped with debugging the switch, LEDs and platfrom
support.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The D-Link DIR-869 A1 doesn't accept images with the jffs2 marker added
after the checksummed range, so we need to include it in the checksum and
fix it on first boot.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
This includes:
- use of local 'board' variable in LED names, wherever possible
- merge of boards with exactly the same LED configuration
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Keep everything in alphabetical order. Boards are ordered in two steps,
first within/inside common configuration (case section), then sections,
globally.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
This includes:
- code style fixes
- removal of huge comment (it should be in doc, not here) and some small ones
- removal of redundant config for DR531/WPJ531 as the default is the same
- merge of boards with exactly the same interfaces config
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Convert etc/board.d/02_network in ar71xx target to the same shape
as we have in ramips target. Split code into two new functions:
- interface/s setup in ar71xx_setup_interfaces()
- MAC/s setup in ar71xx_setup_macs()
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
This patch adds support for Cisco's Z1.
Detailed instructions for the flashing the device can
be found in the OpenWrt wiki:
<https://wiki.openwrt.org/toh/meraki/z1>
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
Local variable declarations outside of functions are illegal since the Busybox
update to v1.25.0, therfore remove them from the appropriate places.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
- quote the interface name
- remove call of not existing function
- remove the proto if it's the default proto
Signed-off-by: Mathias Kresin <dev@kresin.me>
Zbtlink ZBT-WE1526 is based on Qualcomm Atheros QCA9531 v2.
Short specification:
- 650/400/200 MHz (CPU/DDR/AHB)
- 5x 10/100 Mbps Ethernet
- 1x USB 2.0
- 128 MB of RAM (DDR2)
- 16 MB of FLASH
- 2T2R 2.4 GHz, up to 22 dBm
- two external, non-detachable antennas
- 8x LED, 1x button
- UART header (pinout: VCC, RX, TX, GND)
Flash instruction:
Use sysupgrade in vendor firmare which is based on OpenWrt.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
The stock firmware uses the single LED as status indicator only. Using the
same LED both for status and as ethernet indicator is uncommon, and has
been confusing users who were using the device as a WLAN mesh node (so the
LED was just off, as no ethernet was connected).
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
The network defaults for the WZR-HP-G300NH and CR3000 models wrongly set the
lan interface to a vlan tagged device while the switch was set up in untagged
mode, leading to broken lan side ethernet connectivity by default.
Fix the issue by emitting untagged interfaces, consistent with the switch
setting on the device.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
jjPlus JWAP230 is based on Qualcomm Atheros QCA9558 + QCA8337.
Short specification:
- 720/600/200 MHz (CPU/DDR/AHB)
- 2x 10/100/1000 Mbps Ethernet
- 128 MB of RAM (DDR2)
- 16 MB of FLASH
- 3T3R 2.4 GHz with external PA (SST12LP15A), up to 28 dBm
- 3x MMCX connectors
- power input: 802.3at PoE or wide range DC (36-57 V)
- optional 802.3af PSE
- 1x mini-PCIe connector with PCIe, USB buses and SIM slot
- 1x mini-PCIe connector with PCIe bus
- 1x USB type-A connector
- 6x LED, 1x button (hardware reset)
- RS232 (MAX3223) and (E)JTAG headers
Default configuration:
- WAN on eth1 (RJ45 near LEDs with PoE input)
- LAN on eth0 (RJ45 near DC jack)
- left top LED set to be status LED
- all LEDs configurable form user space
Flash instruction (do it under U-Boot, using RS232):
1. tftp 0x80060000 lede-ar71xx-generic-jwap230-squashfs-sysupgrade.bin
2. erase 0x9f050000 +$filesize
3. cp.b $fileaddr 0x9f050000 $filesize
4. setenv bootcmd "bootm 0x9f050000"
5. saveenv && reset
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Wallys DR531 is based on Qualcomm Atheros QCA9531 v2.
Short specification:
- 550/400/200 MHz (CPU/DDR/AHB)
- 2x 10/100 Mbps Ethernet
- 64 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz with external PA (SE2576L), up to 30 dBm
- 2x MMCX connectors
- mini-PCIe connector with PCIe/USB buses and SIM slot
- 7x LED, 1x button, 1x optional buzzer
- UART, (E)JTAG and LED headers
Default configuration:
- WAN on eth1 (RJ45 near DC jack)
- LAN on eth0 (RJ45 near button)
- S4 LED set to be status LED
- all LEDs configurable form user space
- button configured for reset
Flash instruction (do it under U-Boot, using UART):
1. tftp 0x80060000 lede-ar71xx-generic-dr531-squashfs-sysupgrade.bin
2. erase 0x9f050000 +$filesize
3. cp.b $fileaddr 0x9f050000 $filesize
4. setenv bootcmd "bootm 0x9f050000"
5. saveenv && reset
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
It was intended as a workaround when jffs2 eof mark was included in the
checksum calculation in seama header. When qihoo-c301 support was
introduced the board name was not inserted into the case list (because I
was not aware of it's existence), but the issue was fixed by excluding
the jffs2 marker as part of the checksum data
Now we are at it, drop it.
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Reordered the VLANs so the LAN ports are set to VLAN 1 and the WAN port is set to VLAN 2, as in the other routers in the config file. Moreover, this model had this VLAN mapping in OpenWRT Chaos Calmer. It seems that the VLAN were switched when fixing a bug in the port mapping ( OpenWRT changeset 47799 )
Signed-off-by: David Pinilla Caparrós <dpinitux@gmail.com>
This patch adds the target profile SOM9331 and configures hardware
functionality for the 3x Eth Ports & corresponding LED's, the USB Host,
the USART to USB bridge and the System LED.
Signed-off-by: Allan Nick Pedrana <nik9993@gmail.com>
RB912 has one usb shared between external USB and miniPCIe slot. GPIO52 can
reroute power to external USB (=1) or internal miniPCIe slot (=0)
Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
- CPU QCA9531-BL3A
- RAM: 64MB
- flash: 16MB
- USB
AP143 platform, similar to tl-wr841n v10/v11, but with USB
Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
To avoid confusion with different unifiac devices, rename existing target
"unifiac" to "unifiac-lite", before "unifiac-pro" is introduced.
Signed-off-by: P.Wassi <p.wassi at gmx.at>
OpenWrt can be flashed with following uboot commands:
tftpboot 0x80500000 openwrt-ar71xx-generic-wpj342-16M-squashfs-sysupgrade.bin
erase 0x9f030000 +$filesize
cp.b $fileaddr 0x9f030000 $filesize
Signed-off-by: Christian Mehlis <christian@m3hlis.de>
SVN-Revision: 49157
This patch provides full GPIO support for WNR2200 (LEDs and buttons).
It exposes all LEDs to operating system, including Ethernet ones.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
SVN-Revision: 49101
This patch provides full GPIO support for WNR1000v2 (LEDs and buttons).
It exposes all LEDs to operating system, including Ethernet ones.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
SVN-Revision: 49076
This patch provides full GPIO support for WNR612v2 (LEDs and buttons).
It exposes all LEDs to operating system, including Ethernet ones.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
SVN-Revision: 48924
This patch add speed_mask parameter to Ethernet port LED initialization
during system startup. LEDs are configured to show amber light for 10 Mbps
link and green for 100 Mbps as described on device label.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
SVN-Revision: 48923
This patch provides full GPIO support for WNR2000v3 (LEDs and buttons).
It exposes all LEDs to operating system, including Ethernet ones.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
SVN-Revision: 48922
This patch adds support for the Bitmain Antrouter R1
http://wiki.openwrt.org/toh/bitmain/r1
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
SVN-Revision: 48058
The MR18 stores the ath9k eeprom values on the NAND.
This patch makes it possible to retrieve the images
from there.
Signed-off-by: Chris R Blake <chrisrblake93@gmail.com>
SVN-Revision: 47948
move all library includes and 'firmware already exists'
check to the top of the script.
Signed-off-by: Chris R Blake <chrisrblake93@gmail.com>
SVN-Revision: 47947
OpenWrt configuration part of support for the PowerCloud Systems
CR5000. The CR5000 is a dual-band 802.11n wireless router with
8MB flash, 64MB RAM, (unused on stock firmware) USB 2.0 port and
five port gigabit ethernet switch. The CR5000 was sold as
hardware for the Skydog cloud-managed router service.
Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com>
SVN-Revision: 47946
OpenWRt configuration part of support for the PowerCloud
Systems CR3000. The CR3000 is a 802.11n 2.4 GHz wireless router with
8MB flash, 64MB RAM, a four port gigabit ethernet switch, and a fast
ethernet wan port that was sold by PowerCloud Systems as
hardware for the Skydog cloud-managed router service.
Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com>
SVN-Revision: 47945
Openwrt configuration part of support for PowerCloud CAP324
Cloud AP. The CAP324 Cloud AP is a device sold by PowerCloud Systems
who's stock firmware (CloudCommand) provides 'cloud' based managment
of large numbers access points.
The CAP324 is a dual-band 802.11n wireless access point with 16MB flash
and 128MB RAM and single gigabit ethernet port. It can be powered via PoE
or a wall wart.
Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com>
SVN-Revision: 47944
This patch adds support for Cisco's MR18.
Detailed instructions for the flashing the device can
be found in the OpenWrt forum thread:
<https://forum.openwrt.org/viewtopic.php?id=59248>
Signed-off-by: Chris R Blake <chrisrblake93@gmail.com>
SVN-Revision: 47878
Replace former uci-defaults.sh implementation with the uci-defaults-new.sh one
and update all users accordingly.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47867
Include /lib/functions/system.sh in 02_network to define missing
mtd_get_mac_binary() procedure.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47723
This removes calls to ucidef_set_interfaces_lan_wan() and
ucidef_set_interfaces_lan() on boards where all relevant info can be
inferred from the switch definition.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47722
This changes uci-defaults-new.sh, config_generate and all relevant board.d
files in order combine ucidef_add_switch() and ucidef_add_switch_ports() into
a single function.
Also removes now superfluous enable and reset arguments.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47721
Out of 69 switch definitions, only 3 pass something different than "1" as
values for reset and enable, with one of those three being invalid.
This change ...
* removes the reset and enable arguments from ucidef_add_switch()
* unconditionally writes reset:1 and enable:1 to JSON
* converts the three users of nonstandard values to ucidef_add_switch_attr()
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47720
This is based on patches from Federico Fissore <f.fissore@arduino.cc>
especially this one:
7e2976fa83
The console is running with 250000 baud which is a non standard baud
rate and needs an extra patch to be applied, I will try to get this
patch upstream or something else which accomplish the same.
Some upstream code looks like there are many different versions of this
SoC, are these only internal versions and all versions on the consumer
market are the same? I saw different GPIO configuration and flash sizes
of 8MB and 16MB?
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 47451
The international version is completely different from the already
supported Chinese version. The WLAN of the QCA956x SoC used by this router
has been fixed in r46948.
This patch looks like it changes a lot in
700-MIPS-ath79-openwrt-machines.patch; that is not the case. Unfortunately,
quilt decided to completely reorganize the Kconfig patch even though only
a single section has been added.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 47420
This patch supersedes the v1 from September 17th.
Bumping the patch version - the MiniBox profile showed up under M, but
since it's called 'Gainstrong MiniBox v1.0' now it looks out of place.
Renamed the profile to gs-minibox-v1.mk to fix that.
The following patch adds support for the Gainstrong MiniBox into trunk
(or 'Designated Driver' :D ).
Fixed items:
- Inverted LED polarity (OOLITE seems to suffer from the same problem).
- Changed uppercase MINIBOX_V1_ prefix as requested.
- Prefixes are now gs_minibox_ similar to gs_oolite_ (same vendor).
- Mention the vendor (Gainstrong) in code headers.
Compiles fine, has been confirmed working by owners on 15.05.
Question: I've seen some boards use tools/firmware-utils/src/mktplinkfw.c,
the MiniBox images build fine without, so I'm wondering: do I need to add
it in there as well? Any added benefit?
Thank you
Signed-off by: Stijn Segers <francesco.borromini@inventati.org>
SVN-Revision: 47234
Sets the LEDs to boardname:color:led-name
Sets the LAN to eth0
Other corrections such as the Machine Name and HWIDs
v2 corrects the profile names in the Makefile and changes tabs to spaces
in the Makefile 'define Device/' like the other devices.
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
SVN-Revision: 47221
This patch adds kernel and userspace support for the Ubiquiti Networks airGateway Pro.
Signed-off-by: Matthew Reeve <mreeve at tenxnetworks.com>
SVN-Revision: 46961
This patch adds support for TP-LINK TL-WDR3320 v2.
This router uses a chinese version 2 firmware header,.
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
SVN-Revision: 46934
The GPIO pins for "POE passthrough" of Ubiquiti Nanostation models are the
following:
* Ubiquiti Nanostation M XM: Pin 8
* Ubiquiti Nanostation M XW: Pin 2
The previous definition of the pins was mixed up between XM and XW model.
Signed-off-by: Lars Kruse <lists@sumpfralle.de>
SVN-Revision: 46922
This adds full support (sans sysupgrading from vendor firmware) for the COMFAST
CF-E316N v2 (aka CF-E316V2, CF-E316N-V2 and CF-E316Nv2.0, no FCC ID) by
Shenzhen Four Seas Global Link Network Technology Co., Ltd (this company is
actively refusing to provide GPL'd sources for the OpenWrt version they ship
with the device, damn them).
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
SVN-Revision: 46852
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
This patch adds support for TP-Link TL-WDR6500 v2.
The firmware has a U-Boot header for kernel, and a TP-LINK v2 header for
the whole firmware, so I have to create a new firmware creation method.
SVN-Revision: 46663
This patch adds support for the Onion Omega.
https://onion.io/omega
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
Acked-by: Boken Lin <bl@onion.io>
Tested-by: Jacky Huang <huangfangcheng@163.com>
SVN-Revision: 46458
As r46245 disabled the board.bin template workaround, 5GHz wifi stopped working
on these devices. This adds them to the calibration data loading introduced in
r46244 and thus makes 5GHz work again for these devices.
Signed-off-by: Christian Beier <cb@shoutrlabs.com>
SVN-Revision: 46415
Internal GPIO pins are used for PoE passthrough setups in multi-port
routers. This patch implemnets control over this hardware feature for
Ubiquiti Nanostations and TP-Link CPE510.
Signed-off-by: Lars Kruse <lists@sumpfralle.de>
SVN-Revision: 46271
This patch adds support for the Cisco WAP4410N, an access point that uses the
AR9132 SoC. Web upgrades from stock are not yet possible, UART access required
for the initial flash.
Signed-off-by: Ryan A Young <rayoung@utexas.edu>
SVN-Revision: 46250
Currently one board uses the "proper" way of providing firmware
with the name ath10k/cal-pci-<pci address>.bin, whereas other
boards patch board.bin template in preinit and rely on a custom
ath10k patch to use calibration data from the template.
This patch makes all boards use the first method.
Signed-off-by: Matti Laakso <malaakso@elisanet.fi>
SVN-Revision: 46244
This patch adds support for the Bitmain Antminer S3 Cryptocurrency Miner
http://wiki.openwrt.org/toh/bitmain/s3
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
SVN-Revision: 46236
rocket-m titanium is a device based on ar9344 with 802.11af poe.
It doesn't use the SoC wifi, instead it's using an ar9280 connected to
the pci bus. The gps version of the rocket-m ti is working, but
gps is untested. The gps is connected to the first serial port.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
SVN-Revision: 46234
This patch adds support for the Bitmain Antminer S1 Cryptocurrency Miner
http://wiki.openwrt.org/toh/bitmain/s1
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
Acked-by: James Hilliard <james.hilliard1@gmail.com>
SVN-Revision: 46044
This patch is to add support for the Meraki MR12 and MR16 Access Points.
Currently everything is working, minus the 2nd NIC interface on the MR12
which is built into the SoC.
Signed-off-by: Chris R Blake <chrisrblake93 at gmail.com>
SVN-Revision: 45726
It is common that the router provider be used rather than product name.
One can see this in target/linux/ar71xx/base-files/etc/uci-defaults/01_leds
Signed-off-by: Michael J. Bazzinotti <mbazzinotti@gmail.com>
SVN-Revision: 45630
This patch adds support for the XW version of the Rocket M series devices
manufactured by Ubiquiti, based on the Atheros AR9342 SoC.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
SVN-Revision: 45553
None of the LEDs are enabled by default on the Hornet-UB X2 board
(the 16/64MB version of the Hornet-UB), because it uses a different
board-name ("hornet-ub-x2"); but hornet-ub and hornet-ub-x2 boards
are equivalent WRT their LEDs.
SIgned-off-by: Joshua Judson Rosen <jrosen@harvestai.com>
SVN-Revision: 45328
OpenWrt can be flashed with following uboot commands:
tftpboot 0x80500000 openwrt-ar71xx-generic-wpj558-16M-squashfs-sysupgrade.bin
erase 0x9f030000 +$filesize
cp.b $fileaddr 0x9f030000 $filesize
Signed-off-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 44620
This patch adds user-space support for the TL-MR12U board based on the mr13u patches.
Signed-off-by: Daniel Petre <daniel.petre@gmail.com>
SVN-Revision: 44426
This patch adds support for MERCURY MAC1200R, a dual band 802.11bgn + 802.11ac
router based on the AR9344, with QCA988x ath10k radio and 5 Fast Ethernet ports
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
SVN-Revision: 44359
This device is very similar to the TL-WR841N v8, only two LED GPIOs are
different.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 44255
The board is already supported by OpenWrt. WNR1000v2/WNR1000v2-VC are
pretty much the same as WNR2000v3/WNR612v2, therefore the same
initialization code and flash layout is used.
Signed-off-by: Ștefan Rusu <saltwaterc@gmail.com>
Tested-by: Douglas Fraser <1dsfraser@gmail.com>
SVN-Revision: 44221
This patch adds an entry in the uci-defaults' led-file to configure the
WAN and WLAN LEDs by default.
Signed-off-by: Vincent Wiemann <me@bibbl.com>
SVN-Revision: 44165
the GPIO controlling the rf filter is not configured properly by this patch.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 44077
This new argument is used right after starting regular preinit (which
happens if failsafe wasn't triggered). The main purpose of "preinit"
argument is to indicate that failsafe can be triggered, however we were
missing a way to inform user that we don't wait for a trigger anymore.
With this change it's clear when failsafe mode can be triggered.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 43715
