Move nvmem-cells definitions to dts files for compatibility with other files
in which mt7628an_tplink_8m.dtsi is loaded, to prevent overwriting
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Partially revert commit 98ddfbc56a ("generic: 6.6: backport upstream
commits for mtk_eth_soc") as the commit breaks WED. A better solution to
assign PPE units in case of WED has still to be found.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Allow a wider audience to test this pending series.
Use about to be submitted v3 which factors out block notification support.
Apart from dropping the no longer needed (and problematic) fallback for
for the 'partitions' node being present at the device parent there are
no intended functional changes.
As opening a block device as file is not supported yet in Kernel v6.6,
use the previous method as backporting seems a bit too involving.
Fixes: #15642
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The WS-AP3710i does not correctly expose its label-mac on eth0 anymore
since the change to simpleLoader.
Fix this by obtaining the label-mac from the U-Boot environment.
Signed-off-by: David Bauer <mail@david-bauer.net>
With the introduction of the simpleImage loader, the MAC address is not
set by the bootloader anymore.
Fix this by reading the MAC address from the U-Boot environment
partition.
Signed-off-by: David Bauer <mail@david-bauer.net>
We haven't received any bug reports in the past few weeks. So it's
time to set kernel 6.6 as the default and remove kernel 6.1 support.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
The broadcom-wl driver was removed from OpenWrt, remove also the
profiles using it.
Fixes: e772b75d5d ("broadcom-wl: remove package")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The braodcom-wl driver was removed from OpenWrt, remove the special
exports it needed.
Fixes: e772b75d5d ("broadcom-wl: remove package")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This file is executable:
target/linux/ramips/dts/mt7621_dlink_dir-2150-a1.dts
Has to be fixed.
Fixes: 30e8fd73ec ("ramips: Add support for D-Link DIR-2150-A1")
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
This commit fixes random lan mac for sercomm dxx devices.
Fixes: 3395184825 ("ramips: mt7621: nix mac-address-increment")
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
0db4f9785c changed the variable name from
athaddr to ethaddr. Restore.
Fixes: 0db4f9785c ("ath79: convert ath10k calibration data to NVMEM (ASCII MAC)")
Signed-off-by: Rosen Penev <rosenp@gmail.com>
This router has two rootfs partitions and dualboot is used.
Vendor firmware may swap the rootfs partition location, u-boot append
'ubi.mtd=rootfs' in the end of cmdline. Since we use fixed-partitions,
force boot from the first rootfs partition to avoid boot failure.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/15700
Signed-off-by: Robert Marko <robimarko@gmail.com>
Backport an upstream Linux fix to prevent BPF kfunc functions from being
removed during linker optimization when building BTF-enabled vmlinux.
The telltale sign of this occurring is build log warnings (e.g. mips64el):
BTFIDS vmlinux
WARN: resolve_btfids: unresolved symbol bpf_verify_pkcs7_signature
WARN: resolve_btfids: unresolved symbol bpf_lookup_user_key
WARN: resolve_btfids: unresolved symbol bpf_lookup_system_key
WARN: resolve_btfids: unresolved symbol bpf_key_put
WARN: resolve_btfids: unresolved symbol bpf_iter_task_next
WARN: resolve_btfids: unresolved symbol bpf_iter_css_task_new
WARN: resolve_btfids: unresolved symbol bpf_get_file_xattr
WARN: resolve_btfids: unresolved symbol bpf_ct_insert_entry
NM System.map
SORTTAB vmlinux
Link: https://lore.kernel.org/bpf/ZlkoM6%2FPSxVcGM6X@kodidev-ubuntu/
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/15697
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The wifi radios on wax620 and wax630 got a random mac
address on boot. So fix this by using ath11k_patch_mac
and give a static mac address from label-mac-device.
Tested and working on wax620 and wax630.
Signed-off-by: Kristian Skramstad <kristian+github@83.no>
Link: https://github.com/openwrt/openwrt/pull/15597
Signed-off-by: Robert Marko <robimarko@gmail.com>
octeontx is currently stuck on kernel 5.15 since using 6.1 breaks booting,
and unfortunately nobody has stepped up to fix this issue.
Gateworks who were primary users have supported the removal.
Link: https://github.com/openwrt/openwrt/pull/15686
Signed-off-by: Robert Marko <robimarko@gmail.com>
The bump to kernel 6.6 increased the GPIO base from
412 to 512 on this target.
We need to compensate for that in the GPIO numbers being passed
to uci to fix following kernel report:
[ 24.176183] export_store: invalid GPIO 423
Tested on a Wallys DR40x9 board.
Please note that:
Boards "rtl30vw" and "wpj428" are not being altered here.
They define GPIO numbers which are even below the previous
base of 412 which looks wrong.
Actual testing on these boards should be conducted to validate
and optionally fix GPIO numbering.
Suggested-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Koen Vandeputte <koen.vandeputte@citymesh.com>
The WLR-1240 (ZX-5434) is an AC1200 Wave 2 outdoor repeater
with omnidirectional antennas for wall or pole mounting.
The device is manufactured by Todaair and meant to be used with
a tuya-based app, there is no webinterface for configuration.
Specifications:
- MT7628AN, 8 MiB SPI NOR flash, 64 MiB RAM, 2x2 802.11n
- MT7613 2x2 802.11ac Wave 2
- 802.3af PoE or 12V 1A 5.5x2.1 power supply (included)
- top RGB LED ring
TFTP installation:
- rename sysupgrade to `firmware_auto.bin`
- provide at 192.168.1.10 during boot
HTTP installation:
- keep reset button pressed for 5 seconds during power on (light blue
LED flashes slowly, then quickly to confirm, then remains steady on)
- recovery web interface is at 192.168.1.1, upload sysupgrade
Opening the device
- use suction cup to remove top cap within LED ring
- two screws are located in holes underneath silicone sealant
- two further screws are located at the bottom
initramfs boot
- open device, connect serial console (pins are labelled)
- keep pressing `4` during second tftp attempt to enter uboot shell
- run `tftpboot 82000000` to avoid memory overlap, then `bootm`
Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
The WLR-1230 (ZX-5207) is an AC1200 Wave 2 outdoor repeater
with sector antennas for wall or pole mounting.
The device is manufactured by Todaair and meant to be used with
a tuya-based app, there is no webinterface for configuration.
Specifications:
- MT7628AN, 8 MiB SPI NOR flash, 64 MiB RAM, 2x2 802.11n
- MT7613 2x2 802.11ac Wave 2
- 802.3af PoE or 12V 1A 5.5x2.1 power supply (included)
- 3 LEDs WLAN, LAN, RES; PWR LED is not software-controllable
TFTP installation:
- rename sysupgrade to `firmware_auto.bin`
- provide at 192.168.1.10 during boot
HTTP installation:
- keep reset button pressed for 5 seconds during power on (LEDs
flash slowly, then quickly to confirm, then remain steady on)
- recovery web interface is at 192.168.1.1, upload sysupgrade
Opening the device
- two screws are located in the bottom left and right corners
underneath the label, inner tray slides out easily
initramfs boot
- open device, connect serial console (pins are labelled)
- keep pressing `4` during second tftp attempt to enter uboot shell
- run `tftpboot 82000000` to avoid memory overlap, then `bootm`
Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
Add the kmod-mt7915e wifi driver to the default packages for the Ruijie
RG-X60 Pro. kmod-mt7915e has to be added recently and was not done
before merging the support for Ruijie RG-X60 Pro.
Fixes: 3de3c2bdfa ("mediatek: add support for Ruijie RG-X60 Pro")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cudy assigns hardware versions to its devices on its website, and
the Cudy TR1200 router is now Cudy TR1200 v1.
OpenWrt currently uses both variants, and this commit removes
inconsistencies using only the new name.
Signed-off-by: Luis Mita <luis@luismita.com>
Switch to new nvmem binding.
Also fixes a issue that the MAC address assigned to lan/wan was reversed.
Tested-by: Yangyu Chen <cyy@cyyself.name>
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Hardware
--------
- SOC: MediaTek MT7981
- ram: 256MB DDR3
- FLASH: 16MB SPI-NOR
- Ethernet: 2x1Gb Lan 1x1Gb Wan
- WIFI: MediaTek MT7981 2x2 DBDC 802.11ax 2T2R (2.4/5)
- LEDs: 2xLan 1x Wan 1x WIFI 1xSTATUS
MAC table, same as stock firmware:
LAN: 80:3F:5D:xx:xx:x1 partition "hw" at 0x44e (ASCII)
WAN: 80:3F:5D:xx:xx:x2 partition "hw" at 0x460 (ASCII)
2G: 80:3F:5D:xx:xx:x3 partition "factory" at 0x4 (binary), on label
5G: 80:3F:5D:xx:xx:x3 Same as 2G
Installation Method 1: ssh
--------------------------
1. Connect PC to the lan port. Set the PC IP to 192.168.10.100 if
required.
2. Navigate to http://192.168.10.1/
3. Log into the Wavlink WebGUI. Default username/password is
admin/admin.
4. Use WebGUI to upgrade the firmware to
WAVLINK_WN586X3-A_M86X3A_V240113_WO-GDBYFM-modified.bin
downloaded from
https://github.com/themaverickdm/firmware-misc/tree/main/wavlink/wl-wn586x3
Warning: All settings will be lost!
5. Wait about 5 minutes, and after flashing is completed, log into
the router using (with admin123 as password):
ssh root@192.168.10.1
6. scp the openwrt image file onto the router, usually under /tmp
somewhere.
openwrt-mediatek-filogic-wavlink_wl-wn586x3-squashfs-sysupgrade.bin
7. Flash openwrt image file like so:
mtd write \
openwrt-mediatek-filogic-wavlink_wl-wn586x3-squashfs-sysupgrade.bin \
firmware
Warning: Previous firmware will be overwritten!
8. Wait about 5 minutes, and after the flashing is completed, set
the PC IP to 192.168.1.100 if required and log into the router
like so:
ssh root@192.168.1.1
Installation Method 2: u-boot
-----------------------------
1. Connect UART: TX-> 586X3 RX, RX-> 586X3 TX, GND-> 586 GND.
2. Connect PC to the wan (not lan!) port.
3. Setup the tftp server on PC, set IP to 192.168.10.100,
4. Power on the device. Select '2' to upgrade firmware in Uboot.
5. Input the image name and start to upgrade.
Uboot console log:
CPU: MediaTek MT7981
Model: mt7981-rfb
DRAM: 256 MiB
Core: 34 devices, 13 uclasses, devicetree: embed
Loading Environment from nowhere... OK
In: serial@11002000
Out: serial@11002000
Err: serial@11002000
Net:
Warning: ethernet@15100000 (eth0) using random MAC address -
02:47:fb:b2:53:2d
eth0: ethernet@15100000
UBOOT WN586X3A
gpio: pin 9 (gpio 9) value is 0
gpio: pin 10 (gpio 10) value is 0
gpio: pin 5 (gpio 5) value is 0
gpio: pin 12 (gpio 12) value is 0
gpio: pin 13 (gpio 13) value is 0
*** U-Boot Boot Menu ***
1. Startup system (Default)
2. Upgrade firmware
3. Upgrade ATF BL2
4. Upgrade ATF FIP
5. Upgrade single image
6. Load image
0. U-Boot console
Co-authored-by: R Maru <deviantmaru@gmail.com>
Signed-off-by: R Maru <deviantmaru@gmail.com>
Signed-off-by: Sijia Huang <engineer31@win-star.com>
Before the nvmem rework, this was already handled in dts with
mtd-cal-data instead of qca,no-eeprom. No need to duplicate. Also, the
800 size value seems nonsensical. 440 is the standard.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Userspace handling is deprecated.
Also fix a bug with userspace handling where the wrong calibration data
was being used for the PCI card. The dts was correct but userspace was
not.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
These symbols have already been removed from the upstream Linux source
code. They are automatically compared and removed by a kernel config
scanning script[1].
[1] https://github.com/openwrt/openwrt/pull/15324
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
This is an automatically generated commit which aids following Kernel patch
history, as git will see the move and copy as a rename thus defeating the
purpose.
For the original discussion see:
https://lists.openwrt.org/pipermail/openwrt-devel/2023-October/041673.html
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Make the OF-compatible zImage per-board selectable. This allows the
image to only be built with the wrapper if the target actually uses it.
This fixes build-failures for the mpc85xx-p2020 subtarget.
Fixes: 557c094f0579 ("mpc85xx: only build zImage on required targets")
Signed-off-by: David Bauer <mail@david-bauer.net>
Set the appropriate cpu_port value based on the use of realtek,extif0 to extif2
instead of the additional cpu_port parameter.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/15033
Signed-off-by: Robert Marko <robimarko@gmail.com>
Set the appropriate cpu_port value based on the use of realtek,extif0 or realtek,extif1 parameter.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/15033
Signed-off-by: Robert Marko <robimarko@gmail.com>
All NETGEAR EX6150v2 validate the rootfs for which OpenWrt places a
fakeheader at the position, where the bootloader expects it.
Some EX6150v2 bootloaders do however make a broken assumption about
where the rootfs starts. This is due to them calculating the rootfs
start not based upon the kernel-length but the string-offset of the
FIT-image.
We have to be compatible with both this broken as well as the valid
calculation. So we do relocate the FDT string section to a
block-boundary and enlarge the FIT image to end at this boundary +
BLOCKSIZE / 2. This way, both the broken as well as correct calculations
do expect the rootfs-header at the same position.
It is worth noting, that this is a rare edge-case in which only happens
if the image-length as well as the start of the string-section are not
placed in the same erase-block. This is an edge-case which happens very
rarely (thus it was not spotted prior).
Affected:
- U-Boot 2012.07 (Jun 16 2016 - 11:59:37)
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 8f9546f7b0a14f3afa813e39ed45c968ece24464)
The recently added D-Link DNS-320L and the Zyxel NSA310S
is missing an RTC module so let's give them the default
Marvell RTC at least.
Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The gpio is actually low active, fix it.
Fixes: 40e7fab9e4 ("mediatek: add Nokia EA0326GMP support")
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/15651
Signed-off-by: Robert Marko <robimarko@gmail.com>
The IMX device-tree's for arm moved from arch/arm/boot/dts to
arch/arm/boot/dts/nxp/imx. Use that if using the 6.6 kernel.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
copy 6.1 patches to 6.6 and fixup:
- removed patches already upstream
- adapted pathnames of dts patches for new kernel
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Patch 733-01-net-ethernet-mtk_eth_soc-use-napi_build_skb.patch needs
a refresh as line numbers no longer match.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
For the first-time installation (mostly migrates from vendor firmware)
the ubiblock is not ready, but bootdev detection relies on it. This
means users must create ubiblock manually otherwise the sysupgrade
will not work.
Now a unique case is added for nand devices which use new fit format,
let's move to it.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Hardware specification:
SoC: MediaTek MT7981B 2x A53
Flash: 128 MB SPI-NAND
RAM: 256MB
Ethernet: 4x 10/100/1000 Mbps
Switch: MediaTek MT7531AE
WiFi: MediaTek MT7976C
Button: Reset, WPS/Mesh
Power: DC 12V 1A
Gain SSH access:
1. Login into web interface, and download the configuration.
2. Download the configration utilities:
https://firmware.download.immortalwrt.eu.org/cnsztl/mediatek/filogic/openwrt-mediatek-mt7981-nokia-ea0326gmp-config-utils.tar.gz
These binaries are extraced from the factory firmware, which are
dynamically linked with aarch64 musl 1.1.24. To use them, you
must run them under the same runtime environment, otherwise the
binaries will not work properly!
3. Upload the configuration and utilities to a suitable environment.
4. Uncompress the utilities, move them to '/bin' and give them executable permisison:
tar -zxf openwrt-mediatek-mt7981-nokia-ea0326gmp-config-utils.tar.gz
mv mkconfig seama /bin
chmod +x /bin/mkconfig
chmod +x /bin/seama
5. Decrypt and uncompress the configuration:
Enter fakeroot if you are not login as root.
mkconfig -a de-enca -m EA0326GMP_3FE79221BAAA -i EA0326GMP_3FE79221BAAA-xxxxxxxx-backup.tar.gz -o backup.tar.gz
tar -zxf backup.tar.gz
6. Edit 'etc/config/dropbear', set 'enable' to '1'.
7. Edit 'etc/passwd', remove root password: 'root::1:0:99999:7:::'.
8. Repack the configuration:
tar -zcf backup.tar.gz etc/
mkconfig -a enca -m EA0326GMP_3FE79221BAAA -i backup.tar.gz -o EA0326GMP_3FE79221BAAA-xxxxxxxx-backup.tar.gz
9. Upload new configuration via web interface, now you can SSH to EA0326GMP.
A minimum configuration which enabled SSH access is also provided
to simplify the process:
https://firmware.download.immortalwrt.eu.org/cnsztl/mediatek/filogic/openwrt-mediatek-mt7981-nokia-ea0326gmp-enable-ssh.tar.gz
Flash instructions:
1. SSH to EA0326GMP, backup everything, especially 'Factory' part.
2. Write new BL2:
mtd write openwrt-mediatek-filogic-nokia_ea0326gmp-preloader.bin BL2
3. Write new FIP:
mtd write openwrt-mediatek-filogic-nokia_ea0326gmp-bl31-uboot.fip FIP
4. Set static IP on your PC:
IP 192.168.1.254/24, GW 192.168.1.1
5. Serve OpenWrt initramfs image using TFTP server.
6. Cut off the power and re-engage, wait for TFTP recovery to complete.
7. After OpenWrt has booted, perform sysupgrade.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Prior to performing a PROGRAM LOAD RANDOM DATA operation, a WRITE
ENABLE (06h) command must be issued to change the contents of the
memory array. Following a WRITE ENABLE (06) command, **first a PROGRAM
LOAD (02h or 32h) command must be issued to reset the cache**, then
issue a PROGRAM LOAD RANDOM DATA (84h or 34h) command
This is dirty fix provided to use by MediaTek engineer Sky Huang which
may resolve the "OpenWrt Kiss of Death" issue we've been seeing on the
Linksys E8450 aka. Belkin RT3200. However, it means that everything has
to be re-written with that patch already applied, ie. we need to rebuild
the installer once it is part of snapshot builds to have any effect.
Users already on FIP-in-UBI layout are advised to re-write 'fip' UBI
volume and 'bl2' MTD partition manually once from within Linux after
this fix has been applied.
A similar fix will also be required for U-Boot.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Buffalo WSR-2533DHPL2 is a 2.4/5 GHz band 11ac (Wi-Fi 5) router, based
on MediaTek MT7621A.
Specification:
- SoC : MediaTek MT7621AT
- RAM : DDR3 128 MiB (Winbond W631GG6MB12J)
- Flash : RAW-NAND 128 MiB (Winbond W29N01HVSINF)
- WLAN : 2.4/5 GHz (2x MediaTek MT7615N)
- Ethernet : 10/100/1000 Mbps x4
- Switch : MediaTek MT7530 (SoC)
- LED/keys : 8x/6x (2x buttons, 1x slide-switch)
- UART : through-hole on PCB (J4)
- arrangement : 3.3V, GND, TX, RX from triangle-mark
- settings : 57600n8
- Power : 12VDC 1.5A
Flash instruction using factory.bin image:
1. boot WSR-2533DHPL2 normally with "Router" mode
2. access to the WebI ("http://192.168.11.1/") on the device and open
firmware update page
("管理" -> "ファームウェア更新")
3. select the OpenWrt factory.bin image and click update ("更新実行")
button
Attention: do not use "factory-uboot.bin" image
4. Wait ~120 seconds to complete flashing
Flash instruction using initramfs image:
1. prepare the TFTP server with the initramfs image renamed to
"linux.trx-recovery" and IP address "192.168.11.2"
2. press the "AOSS" button while powering on the WSR-2533DHPL2
3. after 10 seconds, release the "AOSS" button, WSR-2533DHPL2 downloads
the initramfs image and boot with it automatically
4. on the initramfs image, download the factory-uboot.bin image to the
device and perform sysupgrade with it and "-F" option
5. wait ~120 seconds to complete flashing
Notes:
- There are 2x factory*.bin images for different purposes.
- factory.bin : for flashing on OEM WebUI
- factory-uboot.bin: for flashing on OEM bootloader or initramfs image
factory-uboot.bin is useful for recoverying the device, or refreshing
when the kernel partition is expanded in the future. sysupgrade on
this device accepts factory-uboot.bin with option "-F", but on that
situation, user configurations won't be kept, so it's not for normal
use.
MAC addresses:
LAN : 18:EC:E7:xx:xx:E0 (board_data, "mac" (text))
WAN : 18:EC:E7:xx:xx:E0 (board_data, "mac" (text))
2.4 GHz: 18:EC:E7:xx:xx:E1 (Factory, 0x4 (hex))
5 GHz : 18:EC:E7:xx:xx:E4 (Factory, 0x8004 (hex))
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Buffalo WSR-2533DHPLS is a 2.4/5 GHz band 11ac router, based on MediaTek
MT7621A.
Very similar to Buffalo WSR-2533DHPL, but with NAND, different GPIO
and TRX partitions.
Specification:
- SoC : MediaTek MT7621AT
- RAM : DDR3 256 MiB (Samsung K4B2G1646F-BYMA)
- Flash : RAW-NAND 128 MiB
(Winbond W29N01HV or KIOXIA TC58BVG0S3HTAI0)
- WLAN : 2.4/5 GHz (2x MediaTek MT7615N)
- Ethernet : 10/100/1000 Mbps
- Switch : MediaTek MT7530 (SoC) 4 ports
- LED/keys : 8x/6x (2x buttons, 1x slide-switch)
- UART : through-hole on PCB (J4)
- arrangement : 3.3V, GND, TX, RX from triangle-mark
- settings : 115200n8
- Power : 12VDC 1.5A
Flash instruction using factory.bin image:
1. boot WSR-2533DHPLS normally with "Router" mode
2. access to the WebI ("http://192.168.11.1/") on the device and open
firmware update page
("管理" -> "ファームウェア更新")
3. select the OpenWrt factory.bin image and click update ("更新実行")
button
Attention: do not use "factory-uboot.bin" image
4. Wait ~120 seconds to complete flashing
Flash instruction using initramfs image:
1. prepare the TFTP server with the initramfs image renamed to
"linux.trx-recovery" and IP address "192.168.11.2"
2. press the "AOSS" button while powering on the WSR-2533DHPLS
3. after 10 seconds, release the "AOSS" button, WSR-2533DHPLS downloads
the initramfs image and boot with it automatically
4. on the initramfs image, download the factory-uboot.bin image to the
device and perform sysupgrade with it and "-F" option
5. wait ~120 seconds to complete flashing
Notes:
- The embedded addresses in eeprom data in Factory partition have
Buffalo's OUI, but they don't match with the actual addresses
assigned to wlan devices. So fixup addresses by the user-space
script.
root@localhost:/# hexdump -C /dev/mtdblock3 | grep "^0000[08]000\s"
00000000 15 76 a0 00 88 57 ee bc 01 a8 15 76 c3 14 00 80 |.v...W.....v....|
00008000 15 76 a0 00 88 57 ee bc 01 f8 15 76 c3 14 00 80 |.v...W.....v....|
See "MAC addresses" below for actual addresses.
- There are 2x factory*.bin images for different purposes.
- factory.bin : for flashing on OEM WebUI
- factory-uboot.bin: for flashing on OEM bootloader or initramfs image
factory-uboot.bin is useful for recoverying the device, or refreshing
when the kernel partition is expanded in the future. sysupgrade on
this device accepts factory-uboot.bin with option "-F", but on that
situation, user configurations won't be kept, so it's not for normal
use.
MAC addresses:
LAN : 90:96:F3:xx:xx:30 (board_data, "mac" (text))
WAN : 90:96:F3:xx:xx:30 (board_data, "mac" (text))
2.4 GHz: 90:96:F3:xx:xx:31
5 GHz : 90:96:F3:xx:xx:38
[original work]
Signed-off-by: Audun-Marius Gangstø <audun@gangsto.org>
[convert to ubi, fix/improve DT, add sysupgrade support]
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Switch trx parser to parser_trx of Linux Kernel from mtdsplit_trx to
split firmware partition using model-specific trx magic number on
some Buffalo devices.
This change is tested on Buffalo WSR-2533DHPL.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Move Build/buffalo-trx to image-commands.mk from image/mt7622.mk to use
that definition from ramips as well.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
This pull request ports Ruijie RG-X60 Pro router support to the main branch.
Parameters:
- SoC : MediaTek MT7986A Quad-core ARM Cortex-A53 2.0GHz
- RAM : DDR3 512MiB (W634GU6QB)
- Flash : SPI-NAND 128 MiB (W25N01GVZEIG)
- WLAN : MediaTek MT7986A integration dual-band WiFi 6
- 2.4 GHz : b/g/n/ax, MIMO 4x4
- 5 GHz : a/n/ac/ax, MIMO 4x4
- Ethernet : 10/100/1000 Mbps x4 (MediaTek MT7531AE)
2500Mbps x 1 (Realtek RTL8221B-VB-CG)
- UART : through-hole on PCB
- [J500] GND, TX, RX, 3.3V (115200n1)
- Buttons : Mesh, Reset
- LEDs : 1x Power (Blue)
1x Turbo (Purple)
- Power : 12 VDC, 3 A
How to Installation:
1. Remove the case and connect the TTL cable to the corresponding position.
2. Power on the device and quickly press "down" on the keyboard, then
U-Boot will stay in the menu.
3. Select "1. Upgrade Firmware", select "0. TFTP Client(Default)".
4. Input the IP address, input the Openwrt image file name to be
flashed, start the TFTP server, and press "Enter".
5. Wait for the flashing to complete.
How return to stock:
1. Remove the case and connect the TTL cable to the corresponding
position.
2. Power on the device and quickly press "down" on the keyboard, then
U-Boot will stay in the menu.
3. Select "1. Upgrade Firmware", select "0. TFTP Client(Default)".
4. Input the IP address, input the Stock “E-WEBOS” image file name to
be flashed, start the TFTP server, and press "Enter".
5. Wait for the flashing to complete.
About recovery:
Connect uart, use u-boot menu to flash stock firmware image or boot
OpenWrt initramfs image.
About MAC Address:
+---------+-------------------+-----------+
| | MAC | Algorithm |
+---------+-------------------+-----------+
| WAN | 10:82:3D:XX:XX:9E | label |
| LAN | 10:82:3D:XX:XX:9F | label+1 |
| WLAN 2g | 10:82:3D:XX:XX:A0 | label+2 |
| WLAN 5g | 10:82:3D:XX:XX:A1 | label+3 |
+---------+-------------------+-----------+
Signed-off-by: Ashley Lee <code@emtips.net>
The Yafut tool now has limited capabilities for working on filesystem
images stored in regular files. This enables preparing Yaffs2 images
for devices with NOR flash using upstream Yaffs2 filesystem code instead
of the custom kernel2minor tool.
Since minimizing the size of the resulting filesystem image size is
important and upstream Yaffs2 code requires two allocator reserve blocks
to be available when writing a file to the filesystem, a trick is
employed while preparing an OpenWRT image: the blank filesystem image
that Yafut operates on initially contains two extra erase blocks that
are chopped off after the kernel file is written. This is safe to do
because Yaffs2 has a true log structure and therefore only ever writes
sequentially (and the size of the kernel file is known beforehand).
While the two extra erase blocks are necessary for writes, Yaffs2 code
seems to be perfectly capable of reading back files from a "truncated"
filesystem that does not contain these extra erase blocks.
In terms of image size, this new approach is only marginally worse than
the current kernel2minor-based one: specifically, upstream Yaffs2 code
needs to write three object headers (each of which takes up an entire
data chunk) when the kernel file is written to the filesystem:
- an object header for the kernel file when it is created,
- an object header for the root directory when the kernel file is
created,
- an updated object header for the kernel file when the latter is
fully written (so that its new size can be recorded).
kernel2minor only writes two of these headers, which is the absolute
minimum required for reading the file back. This means that the
Yafut-based approach causes firmware images to be at most one erase
block (64 kB) larger than those created using kernel2minor, but only in
the very unfortunate scenario where the size of the kernel file is
really close to a multiple of the erase block size.
The rest of the calculations performed when the empty filesystem image
is first prepared stems from the Yaffs2 layout used by MikroTik NOR
devices: each 65,536-byte erase block contains 63 chunks, each of which
consists of 1024 bytes of data followed by 16-byte Yaffs tags without
ECC data; each such group of 63 chunks is then followed by 16 bytes of
padding, which translates to "-C 1040 -B 64k -E" in the Yafut
invocation. Yaffs2 checkpoints and summaries are disabled (using
Yafut's -P and -S switches, respectively) as they are merely performance
optimizations that require extra storage space. The -L and -M switches
are used to force little-endian or big-endian byte order (respectively)
in the resulting filesystem image, no matter what byte order the build
host uses. The tr invocation is used to ensure that the filesystem
image is initialized with 0xFF bytes (which are an indicator of unused
space for Yaffs2 code).
Signed-off-by: Michał Kępień <openwrt@kempniu.pl>
Link: https://github.com/openwrt/openwrt/pull/13453
Signed-off-by: Robert Marko <robimarko@gmail.com>
Instead of extracting WiFi precal as well as MAC addresses in userspace
use recently introduced NVMEM-on-UBI instead.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Tested-by: Christian Lamparter <chunkeey@gmail.com>
Hardware:
- SoC: MediaTek MT7628AN (MIPS 580MHz)
- Flash: 16 MiB XMC 25QH128CH10
- RAM: 128 MiB ESMT M14D1G1664A
- WLAN: 2.4 GHz (MT7628), 5 GHz (MT7613BEN 802.11ac)
- Ethernet: 1x 10/100 Mbps WAN, 1x 10/100 LAN (MT7628)
- USB 2.0 port
- Buttons: 1 Reset button, 1 slider button
- LEDs: 1x Red, 1x White
- Serial console: unpopulated header, 115200 8n1
- Power: 5 VDC, 2 A
MAC addresses:
+---------+-------------------+-----------+
| | MAC | Algorithm |
+---------+-------------------+-----------+
| WAN | 80:af:ca:xx:xx:x0 | label |
| LAN | 80:af:ca:xx:xx:x0 | label |
| WLAN 2g | 80:af:ca:xx:xx:x0 | label |
| WLAN 5g | 80:af:ca:xx:xx:x2 | label+2 |
+---------+-------------------+-----------+
Installation:
The installation must be done via TFTP by disassembling the router.
On other occasions Cudy has distributed intermediate firmware to make
installation easier, and so I recommend checking the Wiki for this
device if there is a more convenient solution than the one below.
To install using TFTP:
1. Upgrade to a beta firmware (signed by Cudy) that can be downloaded
from the wiki. This is required in order to use an unlocked u-boot.
2. Connect to UART.
3. While the router is turning on, press 1.
4. Connect to LAN and set your IP to 192.168.1.88/24. Configure a TFTP
server and an OpenWrt initramfs-kernel.bin firmware file as recovery.bin.
5. Press Enter three times. Verify the filename.
6. If you can reach LuCI or SSH now, just use the sysupgrade image with
the 'Keep settings' option turned off.
If you don't want to use the beta firmware nor the unlocked u-boot, you
can install the firmware writing the sysupgrade image on the firmware
partition of the SPI flash.
Signed-off-by: Luis Mita <luis@luismita.com>
For MT7620, we should always prevent main ethernet interface from
going down due to phy link changes. And the ralink net driver does
not support cable test function, so this patch won't change any
behavior.
Ref:
6fcba5eec3 ("ramips: port 0034-NET-multi-phy-support.patch to 5.4")
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/15591
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
CI tells us that we need to, so lets refresh them.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/15010
Signed-off-by: Robert Marko <robimarko@gmail.com>
Select 6.6 as testing kernel on bcm47xx.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/15010
Signed-off-by: Robert Marko <robimarko@gmail.com>
Since 6.1 is now default, drop 5.15 support.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/15010
Signed-off-by: Robert Marko <robimarko@gmail.com>
Default to kernel 6.1 on bcm47xx.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/15010
Signed-off-by: Robert Marko <robimarko@gmail.com>
Refresh kernel patches. Remove patches already included in the kernel.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/15010
Signed-off-by: Robert Marko <robimarko@gmail.com>
This is an automatically generated commit.
When doing `git bisect`, consider `git bisect --skip`.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/15010
Signed-off-by: Robert Marko <robimarko@gmail.com>
Use ath11k_patch_mac and ath11k_set_macflag functions
instead of fix_wifi_mac script.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/15580
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add support for D-Link DIR-2055 A1 based on similarities to DIR-1960 A1,
as well as various DIR-8xx A1 models. Existing DIR-1960 A1 openwrt
"factory" firmware installs without modifications via the D-Link Recovery
GUI and has no known incompatibilities with the DIR-2055 A1.
Changes to be committed:
new file: target/linux/ramips/dts/mt7621_dlink_dir-2055-a1.dts
modified: target/linux/ramips/image/mt7621.mk
modified: target/linux/ramips/mt7621/base-files/etc/board.d/01_leds
modified: target/linux/ramips/mt7621/base-files/lib/upgrade/platform.sh
Specifications:
Board: Not known
SoC: MediaTek MT7621 Family (MT7621AT)
RAM: 256 MB (Micron 9OK17 D9PTK, should be DDR3 MT41K128M16JT-125)
Flash: 128 MB (Winbond W29N01HVSINA)
WiFi: MediaTek MT7615 Family (MT7615N x2)
Switch: 1 WAN, 4 LAN (Gigabit)
Ports: 1 USB 3.0 (front)
Buttons: Reset, WiFi Toggle, WPS
LEDs: Power (white/orange), Internet (white/orange),
WiFi 2.4G (white), WiFi 5G (white)
Notes:
Only known difference vs. the DIR-1960 A1 is that the DIR-2055 A1
doesn't have a USB activity LED
Serial port:
Tested to be identical to various DIR-8xx A1 models with a similar
enclosure/pcb design:
Parameters: 57600, 8N1, 3.3V TTL no flow control
Location: J1 header (close to the Reset, WiFi and WPS buttons)
Pinout: 1 - VCC 2 - RXD 3 - TXD 4 - GND
Did not connect VCC when using
Installation:
D-Link Recovery GUI: power down the router, press and hold the reset
button, then re-plug it. Keep the reset button pressed until the power
LED starts flashing orange, manually assign a static IP address under
the 192.168.0.xxx subnet (e.g. 192.168.0.2) and go to
http://192.168.0.1
Some modern browsers may have problems flashing via the Recovery GUI,
if that occurs consider uploading the firmware through cURL:
curl -v -i -F "firmware=@file.bin" 192.168.0.1
Signed-off-by: Keith Harrison <keithh@protonmail.com>
The option CONFIG_SND_DRIVERS is activated by default in the generic
configuration, do not deactivate it for tegra. This fixes the build of
the kmod-sound-dummy package on tegra.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Split the kmod-video-dma into kmod-video-dma-sg and
kmod-video-dma-contig. The old one contained two kmods, but sometimes
only one of them is build which caused problems. The configuration
options are not manually selectable in the kernel and hidden in OpenWrt.
Currently this causes build failures on some targets.
Fixes: 4d7cbe0a55 ("kernel: video-dma: explicitly state packaged modules")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
We don't have any passive trip point hence we can set the polling delay
for passive trip to 0 effectively disabling this polling.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Split thermal zone for puzzle chassis. Thermal platform supports only
one sensor per thermal zone.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Fix missing property in puzzle thermal. The thing was never supposed to
work.
Property #thermal-sensor-cells was missing from the puzzle hwmon, making
the entire thermal platform referencing that fail to probe with -EINVAL.
The puzzle hwmon expose 2 termistor but they probably use an userspace
downstream utility to configure and handle thermal. For this reason we
really don't know what they use the sensor for or when it's attached.
We use them to sensor if the Chassis gets too hot due to ambient
temperature and generic components getting too warm.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
- Make step_wise thermal governor respect hysteresis
This is done by importing a downstream patch, backporting the same feature
now present in Linux v6.10+ would be too messy.
- Introduce thermal zone for the WT61P803 uC (chassis and board sensors)
- Introduce thermal zones for AQR NBase-T PHYs
- No longer modify existing SoC thermal zones (which are now only in charge
for emergency shutdown, and can be interrupt driven instead of polled)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Hardware
--------
CPU: Freescale P1020 2xe500 PPC
RAM: 256M DDR3 (Micron MT41J64M16JT-15E:G "D9MNJ")
NAND: 128M (Micron 2CA1)
BTN: 1x Reset
LED: Power - ETH - Radio1 - Radio2
UART: RJ-45 Cisco Pinout - 115200 8N1
Installation
------------
NOTE: You can find a repo with up-to-date instructions as well as
the required files here:
https://github.com/blocktrron/msm460-flashing
Required files
==============
You need a command-files as well as a U-Boot image.
The command-file has the following content (padded to 131072 bytes).
If you copy paste these, remove the newlines!
```
U-BOOT setenv ethaddr 02:03:04:05:06:07; setenv ipaddr 192.168.1.1;
setenv serverip 192.168.1.66; tftpboot 0x3000000 msm460-uboot.bin;
nand device; nand erase 0 0xC0000; nand write 0x3000000 0x0 0xC0000; reset
```
You can download the required U-Boot from this repository:
https://github.com/blocktrron/u-boot-msm/releases
Preparation
===========
Prepare a TFTP server serving two files:
- U-Boot NAND image as `msm460-uboot.bin`.
- OpenWrt factory image as `msm460-factory.bin`
- Command-file names `commands.tftp`
You can start a TFTP server in the current directory using dnsmasq:
```bash
sudo dnsmasq --no-daemon --listen-address=0.0.0.0 \
--port=0 --enable-tftp=enxd0 --tftp-root="$(pwd)" \
--user=root --group=root
```
Replace `enxd0` with the name of your network interface.
Procedure
=========
1. Assign yourself the IP-Address 192.168.1.66/24.
3. Connect the Router to the PC while keeping the reset button
pressed.
4. The LEDs will eventually begin to flash.
They will start to flash faster after around 15 seconds.
5. Release the reset button.
6. Start a new shell
7. Make sure you are currently in the directory where the tftp server
is located.
8. Run the following command:
```bash
tftp 192.168.1.1 -m binary -c put commands.tftp nflashd.cccc9999
```
You get the message "Transfer timed out."
To find out if you have been successful, please check the
blinking LED Pattern.
Signed-off-by: David Bauer <mail@david-bauer.net>
Add a universal zImage which can be loaded by mpc85xx boards at
load address 0x3000000. This allows boards to boot kernels larger than
16MB even if the image is loaded temporarily from NAND at offset
0x1000000 which some bootloaders do by default.
Signed-off-by: David Bauer <mail@david-bauer.net>
Dual-slot NAS based on Marvell Kirkwood.
Specifications:
- Marvell 88F6702 @1GHz
- 256Mb RAM
- 128Mb NAND
- 1x GbE LAN (Marvell 88E1318R)
- 1x USB 2.0
- 2x SATA
- Weltrend WT69P3 ("supervisor" MCU chip)
- Serial on J2 (115200,8n1)
- Newer bootROM so kwboot-ing via serial is possible
Notes:
- The Weltrend MCU is controlled by the package added in utils/dns320l-mcu.
- The original MAC address is stored in the "mini firmware" image's first
17 bytes.
- Compared to the original MTD layout, the uImage+rootfs are now stored in
a common ubi partition.
Installation:
1. Serial console
- Connect your levelshifter to the serial console
on J2 (refer to the wiki page for pinout)
2. Update u-boot
- Download the u-boot.kwb image for the device
- Powercycle the NAS
- Run "kwboot -b u-boot-dns320l/u-boot.kwb /dev/ttyUSB0 -p"
- Connect to the serial console with minicom
- tftp 0x0800000 u-boot-dns320l/u-boot.kwb
(Please note that "PHY reset timed out" seems to be customary
on kirkwood devices, the egiga0 interface works regardless.)
- nand erase 0x0 100000
- nand write 0x0800000 0x0 0x100000
- reset
3. Install OpenWrt
- Boot up the initramfs image
- tftpboot 0x800000 openwrt-kirkwood-generic-dlink_dns320l-initramfs-uImage; bootm 0x800000
- Download the sysupgrade image and perform sysupgrade
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Reviewed-by: Pawel Dembicki <paweldembicki@gmail.com>
Fix broken IB_STANDALONE option for OPKG due to an error in ifdef logic
where we weren't adding the required entry to reference the local files
in repositories.conf
Rework the ifdef to more explicit and restore original functionality of
this option.
While at it also provide different README for APK or OPKG.
Fixes: d788ab376f ("build: add APK package build capabilities")
Link: https://github.com/openwrt/openwrt/pull/15599
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Upstream commit 83b7f0b8aeab ("ARM: tegra: Add OPP tables and power
domains to Tegra20 device-trees") added power domains to all devices
supporting power management and one of them is Video Decoder Engine.
Because of lacking driver for VDE, its power gate couldn't be driven
which inhibited reboot of the whole device.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Simple refresh to get rid of any fuzz and drop serial patch. With few
bug fixes around tegra serial driver the spurious IRQ didn't appear any
more during test. Let's see how long that'll last.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
This is an automatically generated commit which aids following Kernel patch
history, as git will see the move and copy as a rename thus defeating the
purpose.
For the original discussion see:
https://lists.openwrt.org/pipermail/openwrt-devel/2023-October/041673.html
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
This is an automatically generated commit.
When doing `git bisect`, consider `git bisect --skip`.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Use a simple Shell script like on filogic target to get rid of downstream
patch for the Ethernet driver which was rejected upstream long ago.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This adds the legacy /dev/fb* device file for kernel 6.6 again.
Linux upstream commit 701d2054fa31 ("fbdev: Make support for
userspace interfaces configurable") made this configurable and we
deactivated this option by default for kernel 6.6. On x86 we are not
space constrained and some users need this legacy interface.
Fixes: #15222
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Backport commit fixing detection of SFP modules which has been broken
since Linux 6.4 for some modules.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
In preparation to update to upcoming Linux 6.6.33 move accepted patches
from mediatek target to backport folder, so moving to newer Linux 6.6
releases becomes easier and also other patches on top can be applied
more easily.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Make sure all patches can again be applied using 'git am' on the
corresponding linux-stable git tree.
Fixes: a7ae4ed0a3 ("kernel: fix tools build breakage on macos with x86")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This is an automatically generated commit which aids following Kernel patch
history, as git will see the move and copy as a rename thus defeating the
purpose.
For the original discussion see:
https://lists.openwrt.org/pipermail/openwrt-devel/2023-October/041673.html
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Fix compile error:
drivers/dma/ralink-gdma.c: In function 'gdma_dma_config':
drivers/dma/ralink-gdma.c:197:40: error: 'struct dma_slave_config' has no member named 'slave_id'
197 | chan->slave_id = config->slave_id;
| ^~
drivers/dma/ralink-gdma.c:206:40: error: 'struct dma_slave_config' has no member named 'slave_id'
206 | chan->slave_id = config->slave_id;
| ^~
make[8]: *** [scripts/Makefile.build:243: drivers/dma/ralink-gdma.o] Error 1
ref: https://lore.kernel.org/all/20211122222203.4103644-1-arnd@kernel.org/
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
The gdma driver has been removed from the upstream. Let's move it
to the local files. This patch also removed unsupported compatible
string and sub-target.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Add missing ';;' to the end of shell switch case statement.
Fixes: c71b68acdd ("mediatek: filogic: add Adtran SmartRG Mount Stuart series")
Reported-by: @gl-dude
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Disable image building for the board, since the kernel of the main branch
is to big to fit into the kernel partition.
Signed-off-by: Nick Hainke <vincent@systemli.org>
Dell/SonicWall APL26-0AE (marketed as SonicPoint ACe) is a dual band
wireless access point. End of life as of 2022-07-31.
Specification
SoC: QualcommAtheros QCA9550
RAM: 256 MB DDR2
Flash: 32 MB SPI NOR
WIFI: 2.4 GHz 3T3R integrated
5 GHz 3T3R QCA9890 oversized Mini PCIe card
Ethernet: 2x 10/100/1000 Mbps QCA8334
port labeled lan1 is PoE capable (802.3at)
USB: 1x 2.0
LEDs: LEDs: 6x which 5 are GPIO controlled and two of them are dual color
Buttons: 2x GPIO controlled
Serial: RJ-45 port, SonicWall pinout
baud: 115200, parity: none, flow control: none
Before flashing, be sure to have a copy of factory firmware, in case You
wish to revert to original firmware.
All described procedures were done in following environment:
ROM Version: SonicROM (U-Boot) 8.0.0.0-11o
SafeMode Firmware Version: SonicOS 8.0.0.0-14o
Firmware Version: SonicOS 9.0.1.0
In case of other versions, following installation instructions might be
ineffective.
Installation
1. Prepare TFTP server with OpenWrt sysupgrade image and rename that
image to "sp_fw.bin".
2. Connect to one of LAN ports.
3. Connect to serial port.
4. Hold the reset button (small through hole on side of the unit),
power on the device and when prompted to stop autoboot, hit any key.
The held button can now be released.
5. Alter U-Boot environment with following commands:
setenv bootcmd bootm 0x9F110000
saveenv
6. Adjust "ipaddr" (access point, default is 192.168.1.1) and "serverip"
(TFTP server, default is 192.168.1.10) addresses in U-Boot
environment, then run following commands:
tftp 0x80060000 sp_fw.bin
erase 0x9F110000 +0x1EF0000
cp.b 0x80060000 0x9F110000 $filesize
7. After successful flashing, execute:
boot
8. The access point will boot to OpenWrt. Wait few minutes, until the
wrench LED will stop blinking, then it's ready for configuration.
Known issues
Initramfs image can't be bigger than specified kernel size, otherwise
bootloader will throw LZMA decompressing error. Switching to lzma-loader
should workaround that.
This device has Winbond 25Q256FVFG and doesn't have reliable reset, which
causes hang on reboot, thus broken-flash-reset needs to be added. This
property addition causes dispaly of "scary" warning on each boot, take
this warnig into consideration.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
After the spliting dts folder of ARM architecture in upstream,
layerscape routines need to be adjusted for new solution.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Mostly done by 'make kernel_oldconfig'.
armv8_64b has added one entry manually:
CONFIG_CRYPTO_CURVE25519=y
as workaround for error:
aarch64-openwrt-linux-musl-ld: crypto/crypto_engine.o: in function
`crypto_engine_register_kpp':
crypto_engine.c:687: undefined reference to `crypto_register_kpp'
crypto_engine.c:687:(.text+0x57c): relocation truncated to fit:
R_AARCH64_CALL26 against undefined symbol `crypto_register_kpp'
aarch64-openwrt-linux-musl-ld: crypto/crypto_engine.o: in function
`crypto_engine_unregister_kpp':
crypto/crypto_engine.c:693: undefined reference to `crypto_unregister_kpp'
crypto_engine.c:693:(.text+0x5a0): relocation truncated to fit:
R_AARCH64_CALL26 against undefined symbol `crypto_unregister_kpp'
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
This is an automatically generated commit which aids following Kernel patch history,
as git will see the move and copy as a rename thus defeating the purpose.
See: https://lists.openwrt.org/pipermail/openwrt-devel/2023-October/041673.html
for the original discussion.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
This is an automatically generated commit.
During a `git bisect` session, `git bisect --skip` is recommended.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Fortinet FortiWiFi 51E (FWF-51E) is a UTM with 1x WLAN and 1x SSD, based
on Armada 385 (88F6820).
Specification:
- SoC : Marvell Armada 385 88F6820
- RAM : DDR3 2 GiB (4x Micron MT41K512M8DA-107, "D9SGQ")
- Flash : SPI-NOR 128 MiB (Macronix MX66L1G45GMI-10G)
- SSD : mSATA SSD 32 GB (A-DATA XM21E (AXM21ES3-32GM-B))
- mode : SATA III 6Gbps
- power : 3.3 VDC, 3.1 W (Max.)
- Ethernet : 7x 10/100/1000 Mbps
- LAN 1-5 : Marvell 88E6176
- WAN 1, 2 : Marvell 88E1512 (2x)
- WLAN : Fortinet EMP7618-FT (Atheros AR9382 (2T2R))
- interface : MiniPCIe
- LEDs/Keys : 18x/1x
- UART : "CONSOLE" port (RJ-45, RS-232C level)
- port : ttyS0
- settings : 9600bps 8n1
- assignment : 1:NC , 2:NC , 3:TXD, 4:GND,
5:GND, 6:RXD, 7:NC , 8:NC
- note : compatible with Cisco console cable
- HW Monitoring: nuvoTon NCT7802Y
- Power : 12 VDC, 2 A
- plug : Molex 5557-02R
Flash instruction using initramfs image:
1. Power on FWF-51E and interrupt to show bootmenu
2. Call "[I]: System information." -> "[S]: Set serial port baudrate."
and set baudrate to 9600 bps
3. Call "[R]: Review TFTP parameters.", check TFTP parameters and
connect computer to "Image download port" in the parameters
4. Prepare TFTP server with the parameters obtained above
5. Rename OpenWrt initramfs image to "image.out" and put to TFTP
directory
6. Call "[T]: Initiate TFTP firmware transfer." to download initramfs
image from TFTP server
7. Type "R" key when the following message is showed, to boot initramfs
image without flashing to spi-nor flash
"Save as Default firmware/Backup firmware/Run image without saving:[D/B/R]?"
8. On initramfs image, backup mtd if needed
minimum:
- "firmware-info"
- "kernel"
- "rootfs"
9. On initramfs image, upload sysupgrade image to the device and perform
sysupgrade
10. Wait ~200 seconds to complete flashing and rebooting.
If the device is booted with stock firmware, login to bootmenu and
call "[B]: Boot with backup firmware and set as default." to set the
first OS image as default and boot it.
Notes:
- Both colors of Bi-color LEDs on the front panel cannot be turned on at
the same time.
- "PWR" and "Logo" LEDs are connected to power source directly.
- The following partitions are added for OpenWrt.
These partitions are contained in "uboot" partition (0x0-0x1fffff) on
stock firmware.
- "firmware-info"
- "dtb"
- "u-boot-env"
- "board-info"
Image header for bootmenu tftp:
0x0 - 0xf : ?
0x10 - 0x2f : Image Name
0x30 - 0x17f: ?
0x180 - 0x183: Kernel Offset*
0x184 - 0x187: Kernel Length*
0x188 - 0x18b: RootFS Offset (ext2)*
0x18c - 0x18f: RootFS Length (ext2)*
0x190 - 0x193: DTB Offset
0x194 - 0x197: DTB Length
0x198 - 0x19b: Data Offset (jffs2)
0x19c - 0x19f: Data Length (jffs2)
0x1a0 - 0x1ff: ?
*: required for initramfs image
MAC addresses:
(eth0): 90:6C:AC:xx:xx:98 (board-info (OpenWrt), 0xd880 (hex))
WAN 1 : 90:6C:AC:xx:xx:99
WAN 2 : 90:6C:AC:xx:xx:9A
LAN 1 : 90:6C:AC:xx:xx:9B
LAN 2 : 90:6C:AC:xx:xx:9C
LAN 3 : 90:6C:AC:xx:xx:9D
LAN 4 : 90:6C:AC:xx:xx:9E
LAN 5 : 90:6C:AC:xx:xx:9F
WLAN : 88:DC:96:xx:xx:xx (MiniPCIe Card)
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Tested-by: Raylynn Knight <rayknight@me.com>
Fortinet FortiWiFi 50E-2R (FWF-50E-2R) is a UTM with 2x WLAN, based on
Armada 385 (88F6820).
Specification:
- SoC : Marvell Armada 385 88F6820
- RAM : DDR3 2 GiB (4x Nanya NT5CC512M8EN-EK)
- Flash : SPI-NOR 128 MiB (Macronix MX66L1G45GMI-10G)
- Ethernet : 7x 10/100/1000 Mbps
- LAN 1-5 : Marvell 88E6176
- WAN 1, 2 : Marvell 88E1512 (2x)
- WLAN : Gemtek WMDQ-177ACN (Qualcomm Atheros QCA9892 (2T2R))
(2x)
- interface : MiniPCIe
- LEDs/Keys : 18x/1x
- UART : "CONSOLE" port (RJ-45, RS-232C level)
- port : ttyS0
- settings : 9600bps 8n1
- assignment : 1:NC , 2:NC , 3:TXD, 4:GND,
5:GND, 6:RXD, 7:NC , 8:NC
- note : compatible with Cisco console cable
- HW Monitoring: nuvoTon NCT7802Y
- Power : 12 VDC, 2.5 A
- plug : Molex 5557-02R
Flash instruction using initramfs image:
1. Power on FWF-50E-2R and interrupt to show bootmenu
2. Call "[I]: System information." -> "[S]: Set serial port baudrate."
and set baudrate to 9600 bps
3. Call "[R]: Review TFTP parameters.", check TFTP parameters and
connect computer to "Image download port" in the parameters
4. Prepare TFTP server with the parameters obtained above
5. Rename OpenWrt initramfs image to "image.out" and put to TFTP
directory
6. Call "[T]: Initiate TFTP firmware transfer." to download initramfs
image from TFTP server
7. Type "R" key when the following message is showed, to boot initramfs
image without flashing to spi-nor flash
"Save as Default firmware/Backup firmware/Run image without saving:[D/B/R]?"
8. On initramfs image, backup mtd if needed
minimum:
- "firmware-info"
- "kernel"
- "rootfs"
9. On initramfs image, upload sysupgrade image to the device and perform
sysupgrade
10. Wait ~200 seconds to complete flashing and rebooting.
If the device is booted with stock firmware, login to bootmenu and
call "[B]: Boot with backup firmware and set as default." to set the
first OS image as default and boot it.
Notes:
- Both colors of Bi-color LEDs on the front panel cannot be turned on at
the same time.
- "PWR" and "Logo" LEDs are connected to power source directly.
- The following partitions are added for OpenWrt.
These partitions are contained in "uboot" partition (0x0-0x1fffff) on
stock firmware.
- "firmware-info"
- "dtb"
- "u-boot-env"
- "board-info"
Image header for bootmenu tftp:
0x0 - 0xf : ?
0x10 - 0x2f : Image Name
0x30 - 0x17f: ?
0x180 - 0x183: Kernel Offset*
0x184 - 0x187: Kernel Length*
0x188 - 0x18b: RootFS Offset (ext2)*
0x18c - 0x18f: RootFS Length (ext2)*
0x190 - 0x193: DTB Offset
0x194 - 0x197: DTB Length
0x198 - 0x19b: Data Offset (jffs2)
0x19c - 0x19f: Data Length (jffs2)
0x1a0 - 0x1ff: ?
*: required for initramfs image
MAC addresses:
(eth0): 90:6C:AC:xx:xx:98 (board-info (OpenWrt), 0xd880 (hex))
WAN 1 : 90:6C:AC:xx:xx:99
WAN 2 : 90:6C:AC:xx:xx:9A
LAN 1 : 90:6C:AC:xx:xx:9B
LAN 2 : 90:6C:AC:xx:xx:9C
LAN 3 : 90:6C:AC:xx:xx:9D
LAN 4 : 90:6C:AC:xx:xx:9E
LAN 5 : 90:6C:AC:xx:xx:9F
WLAN 1: 1C:49:7B:xx:xx:xx (MiniPCIe Card)
WLAN 2: 1C:49:7B:xx:xx:xx (MiniPCIe Card)
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Tested-by: Raylynn Knight <rayknight@me.com>
Fortinet FortiGate 52E (FG-52E) is a UTM, based on Armada 385 (88F6820).
Specification:
- SoC : Marvell Armada 385 88F6820
- RAM : DDR3 2 GiB (4x Micron MT41K512M8DA-107, "D9SGQ")
- Flash : SPI-NOR 128 MiB (Macronix MX66L1G45GMI-10G)
- SSD : mSATA SSD 64 GB (2x A-DATA XM21E (AXM21ES3-32GM-B))
- mode : SATA III 6Gbps
- power : 3.3 VDC, 3.1 W (Max.)
- Ethernet : 7x 10/100/1000 Mbps
- LAN 1-5 : Marvell 88E6176
- WAN 1, 2 : Marvell 88E1512 (2x)
- LEDs/Keys : 18x/1x
- UART : "CONSOLE" port (RJ-45, RS-232C level)
- port : ttyS0
- settings : 9600bps 8n1
- assignment : 1:NC , 2:NC , 3:TXD, 4:GND,
5:GND, 6:RXD, 7:NC , 8:NC
- note : compatible with Cisco console cable
- HW Monitoring: nuvoTon NCT7802Y
- Power : 12 VDC, 2.5 A
- plug : Molex 5557-02R
Flash instruction using initramfs image:
1. Power on FG-52E and interrupt to show bootmenu
2. Call "[I]: System information." -> "[S]: Set serial port baudrate."
and set baudrate to 9600 bps
3. Call "[R]: Review TFTP parameters.", check TFTP parameters and
connect computer to "Image download port" in the parameters
4. Prepare TFTP server with the parameters obtained above
5. Rename OpenWrt initramfs image to "image.out" and put to TFTP
directory
6. Call "[T]: Initiate TFTP firmware transfer." to download initramfs
image from TFTP server
7. Type "R" key when the following message is showed, to boot initramfs
image without flashing to spi-nor flash
"Save as Default firmware/Backup firmware/Run image without saving:[D/B/R]?"
8. On initramfs image, backup mtd if needed
minimum:
- "firmware-info"
- "kernel"
- "rootfs"
9. On initramfs image, upload sysupgrade image to the device and perform
sysupgrade
10. Wait ~200 seconds to complete flashing and rebooting.
If the device is booted with stock firmware, login to bootmenu and
call "[B]: Boot with backup firmware and set as default." to set the
first OS image as default and boot it.
Notes:
- Both colors of Bi-color LEDs on the front panel cannot be turned on at
the same time.
- "PWR" and "Logo" LEDs are connected to power source directly.
- The following partitions are added for OpenWrt.
These partitions are contained in "uboot" partition (0x0-0x1fffff) on
stock firmware.
- "firmware-info"
- "dtb"
- "u-boot-env"
- "board-info"
Image header for bootmenu tftp:
0x0 - 0xf : ?
0x10 - 0x2f : Image Name
0x30 - 0x17f: ?
0x180 - 0x183: Kernel Offset*
0x184 - 0x187: Kernel Length*
0x188 - 0x18b: RootFS Offset (ext2)*
0x18c - 0x18f: RootFS Length (ext2)*
0x190 - 0x193: DTB Offset
0x194 - 0x197: DTB Length
0x198 - 0x19b: Data Offset (jffs2)
0x19c - 0x19f: Data Length (jffs2)
0x1a0 - 0x1ff: ?
*: required for initramfs image
MAC addresses:
(eth0): 90:6C:AC:xx:xx:98 (board-info (OpenWrt), 0xd880 (hex))
WAN 1 : 90:6C:AC:xx:xx:99
WAN 2 : 90:6C:AC:xx:xx:9A
LAN 1 : 90:6C:AC:xx:xx:9B
LAN 2 : 90:6C:AC:xx:xx:9C
LAN 3 : 90:6C:AC:xx:xx:9D
LAN 4 : 90:6C:AC:xx:xx:9E
LAN 5 : 90:6C:AC:xx:xx:9F
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Fortinet FortiGate 51E (FG-51E) is a UTM, based on Armada 385 (88F6820).
Specification:
- SoC : Marvell Armada 385 88F6820
- RAM : DDR3 2 GiB (4x Micron MT41K512M8DA-107, "D9SGQ")
- Flash : SPI-NOR 128 MiB (Macronix MX66L1G45GMI-10G)
- SSD : mSATA SSD 32 GB (A-DATA XM21E (AXM21ES3-32GM-B))
- mode : SATA III 6Gbps
- power : 3.3 VDC, 3.1 W (Max.)
- Ethernet : 7x 10/100/1000 Mbps
- LAN 1-5 : Marvell 88E6176
- WAN 1, 2 : Marvell 88E1512 (2x)
- LEDs/Keys : 18x/1x
- UART : "CONSOLE" port (RJ-45, RS-232C level)
- port : ttyS0
- settings : 9600bps 8n1
- assignment : 1:NC , 2:NC , 3:TXD, 4:GND,
5:GND, 6:RXD, 7:NC , 8:NC
- note : compatible with Cisco console cable
- HW Monitoring: nuvoTon NCT7802Y
- Power : 12 VDC, 2.5 A
- plug : Molex 5557-02R
Flash instruction using initramfs image:
1. Power on FG-51E and interrupt to show bootmenu
2. Call "[I]: System information." -> "[S]: Set serial port baudrate."
and set baudrate to 9600 bps
3. Call "[R]: Review TFTP parameters.", check TFTP parameters and
connect computer to "Image download port" in the parameters
4. Prepare TFTP server with the parameters obtained above
5. Rename OpenWrt initramfs image to "image.out" and put to TFTP
directory
6. Call "[T]: Initiate TFTP firmware transfer." to download initramfs
image from TFTP server
7. Type "R" key when the following message is showed, to boot initramfs
image without flashing to spi-nor flash
"Save as Default firmware/Backup firmware/Run image without saving:[D/B/R]?"
8. On initramfs image, backup mtd if needed
minimum:
- "firmware-info"
- "kernel"
- "rootfs"
9. On initramfs image, upload sysupgrade image to the device and perform
sysupgrade
10. Wait ~200 seconds to complete flashing and rebooting.
If the device is booted with stock firmware, login to bootmenu and
call "[B]: Boot with backup firmware and set as default." to set the
first OS image as default and boot it.
Notes:
- Both colors of Bi-color LEDs on the front panel cannot be turned on at
the same time.
- "PWR" and "Logo" LEDs are connected to power source directly.
- The following partitions are added for OpenWrt.
These partitions are contained in "uboot" partition (0x0-0x1fffff) on
stock firmware.
- "firmware-info"
- "dtb"
- "u-boot-env"
- "board-info"
Image header for bootmenu tftp:
0x0 - 0xf : ?
0x10 - 0x2f : Image Name
0x30 - 0x17f: ?
0x180 - 0x183: Kernel Offset*
0x184 - 0x187: Kernel Length*
0x188 - 0x18b: RootFS Offset (ext2)*
0x18c - 0x18f: RootFS Length (ext2)*
0x190 - 0x193: DTB Offset
0x194 - 0x197: DTB Length
0x198 - 0x19b: Data Offset (jffs2)
0x19c - 0x19f: Data Length (jffs2)
0x1a0 - 0x1ff: ?
*: required for initramfs image
MAC addresses:
(eth0): 70:4C:A5:xx:xx:98 (board-info (OpenWrt), 0xd880 (hex))
WAN 1 : 70:4C:A5:xx:xx:99
WAN 2 : 70:4C:A5:xx:xx:9A
LAN 1 : 70:4C:A5:xx:xx:9B
LAN 2 : 70:4C:A5:xx:xx:9C
LAN 3 : 70:4C:A5:xx:xx:9D
LAN 4 : 70:4C:A5:xx:xx:9E
LAN 5 : 70:4C:A5:xx:xx:9F
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Tested-by: Raylynn Knight <rayknight@me.com>
Add a new dtsi which contains the common parts of Fortinet
FortiGate/FortiWiFi 5xE series devices.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Add a new dtsi which contains the common parts of Fortinet
FortiGate/FortiWiFi 3xE series devices.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Rename the common dtsi of Fortinet FortiGate 30E/50E for the preparation
of adding support for the other FortiGate/FortiWiFi 3xE/5xE devices.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Add a common definition of Fortinet FortiGate devices to
image/cortexa9.mk for a preparation of adding support for
other FortiGate 3xE/5xE devices.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Hardware:
SoC: Qualcomm Atheros QCA956X ver 1 rev 0
CPU clock: 775.000 MHz
Memory: 128 MB DDR2
Flash: 32 MB SPI NOR mx25l25635e
Switch: Atheros AR8327 rev. 4
Ethernet: 5x 10/100/1000 Mbps (1 WAN + 4 LAN)
Buttons: 1x Reset
Serial: TX, RX, GND, VCC
Baudrate: 115200
Wifi: Qualcomm Atheros qca988x 802.11ac/n - 3x3
Qualcomm Atheros AR9561 802.11b/g/n - 3x3
Not working:
Leds: 1x via a SPI controller
Display: ST7789V or ILI9341V
controlled by stm32f205.
Note:
DSA changes are ready, but we have an issue with
ports not working after 20-30 minutes. So for now
we use swconfig.
Installation: serial connection only
There is a J11 four pin connector. You need to connect TX, RX and GND.
You can find very good information about the device here
https://github.com/alexanderhenne/AFi-R?tab=readme-ov-file#finding-j11
Upgrading via serial port:
1. Download the kernel initramfs image. Copy the image to a TFTP server
2. Connect to console on the AP, and connect the LAN1 port to your PC LAN
3. Stop autoboot to get to U-boot shell
Interrupt the autoboot process by pressing any key when prompted
4. Transfer the kernel image with TFTP
Set your ip address on your TFTP server to 192.168.1.254
# tftpboot 0x81000000 amplifi-router-hd-initramfs-kernel.bin
5. Load the image
# bootm 0x81000000
6. SCP sysupgrade image from your PC to the Amplifi HD
(If you use a newer mac use scp -O)
# scp openwrt-ath79-generic-ubnt_amplifi-router-hd-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/
7. Write sysupgrade to the firmware partition
# mtd write /tmp/openwrt-ath79-generic-ubnt_amplifi-router-hd-squashfs-sysupgrade.bin firmware
8. Reboot your device
# reboot
Credit to alexanderhenne for all the information.
Signed-off-by: Kristian Skramstad <kristian+github@83.no>
ELECOM WRC-X1800GS is a 2.4/5 GHz band 11ax (Wi-Fi 6) router, based on
MT7621A.
Specification:
- SoC : MediaTek MT7621A
- RAM : DDR3 256 MiB
- Flash : RAW-NAND 128 MiB (Macronix MX30LF1G28AD-TI)
- WLAN : 2.4/5 GHz 2T2R (MediaTek MT7915D)
- Ethernet : 5x 10/100/1000 Mbps
- switch : MediaTek MT7530 (SoC)
- LEDs/Keys (GPIO) : 7x/4x
- UART : pin-header on PCB ("J5")
- arrangement : 3.3V, TX, RX, NC, GND from tri-angle marking
- settings : 115200n8
- Power : 12 VDC, 1 A
Flash instruction using initramfs-factory image:
1. Boot WRC-X1800GS normally with "Router" mode
2. Access to "http://192.168.2.1/" and open firmware update page
("ファームウェア更新")
3. Select the OpenWrt initramfs-factory image and click apply ("適用")
button
4. After flashing initramfs-factory image and reboot, upload the
sysupgrade image and perform sysupgrade with it
5. Wait ~120 seconds to complete flashing
Notes:
- WRC-X1800GS has 2x os images. Those are switched on every firmware
updating on stock firmware, but dual-boot feature on this device
cannot be handled on OpenWrt. So the 1st image is always used on
OpenWrt.
This is controlled by "bootnum" variable embedded in "persist"
partition (addr: 0x4).
- WRC-X1800GS has 2x HW revisions. There are some small changes, but the
same DeviceTree in stock firmware is used for both revisions.
On this support of WRC-X1800GS, 2x green:wlan-2g-N LEDs are defined
for each revision and the same default triggers are set.
MAC addresses:
LAN : 38:97:A4:xx:xx:38 (Factory, 0x1fdfa (hex) / Ubootenv, ethaddr (text))
WAN : 38:97:A4:xx:xx:3B (Factory, 0x1fdf4 (hex))
2.4 GHz: 38:97:A4:xx:xx:39
5 GHz : 38:97:A4:xx:xx:3A
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
The EnGenius EAP1300 and EAP1300EXT use identical boards and firmware
(as flashed) from the vendor.
As with the EAP1300, the EAP1300EXT requires a specific firmware version
to flash OpenWRT. Unfortunately, the required firmware is truncated on
the vendor's website.
A working file can be created as follows:
```
curl \
https://www.engeniustech.com/wp_firmware/eap1300-all-v3.5.3.5_c1.9.04.bin \
| perl -pe 's/\x09EAP1300_A/\x0cEAP1300EXT_A/' \
> eap1300ext-all-v3.5.3.5_c1.9.04.bin
```
The file should have sha256:
`58a1197a426139a12b03fd432334e677124cbe3384349bd7337f2ee71f1dcfd4`.
Please see commit 2b4ac79 for further
details.
The vendor firmware must be decrypted before it can be flashed from
OpenWRT. A tool able to do that is available from:
https://github.com/ryancdotorg/enfringement/blob/main/decrypt.py
Signed-off-by: Ryan Castellucci <code@ryanc.org>
The vendor U-Boot on the Cudy M3000 and the Yuncore AX835 assign random
mac addresses on boot and set the 'local-mac-address' property which
prevents Openwrt from assigning the correct address from evmem.
This patch removes the alias for ethernet0 so that U-Boot doesn't add the
property, removes the workaround from 02_network, and adds back the nvmem
definition for the M3000.
Signed-off-by: Leon M. Busch-George <leon@georgemail.eu>
OpenWrt supported the D-Link DSM G600 A in the past. It has
64 MB of RAM and 16 MB of flash so it will run just fine,
and should be quite usable with a rootfs on an external
harddrive.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
OpenWrt supported the Freecom FSG-3 in the past. It has
64 MB of RAM so will run fine, but the bare 4 MB of flash
makes it a non-default target. The generated compressed
image is currently below 4MB (just 3.3 MB) though, so it
should be possible to flash just fine with a rootfs on
a harddrive or USB stick, which is what the FSG-3 used
in the past as well.
The device has a WAN port on eth0 and three LAN ports on
eth1. The LAN ports are probably a DSA switch but the
old OpenWrt base never activated that, instead it relies
on boot defaults.
Due to questionable usablity without tweaking and further
work this image is not built by default, but made available
for developers who know what they are doing.
The TAR+CRC image generation is a rewritten version of the
earlier support code.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
OpenWrt supported the Iomega NAS100D in the past and it has
64 MB of RAM so if booted from a harddrive it will probably
work just fine. The APEX boot loader already has a build
variant for this machine that we can just pick up and use.
This device has a single ethernet port so bring this online
with DHCP as expected for a NAS device.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Several of the IXP4xx machines mount root on external harddrives
so add EXT4 and rootfs-part to the featureset so the right
features are always selected.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Common specifications:
* Mediatek MT7988A (4x Cortex-A73, up to 1.8 GHz clock speed)
* 8 GiB eMMC
* 2 GiB DDR4 RAM
* 1x 10000M/1000M/100M + 3x 1000M/100M/10M LAN ports
* MT7996 Tri-band (2.4G, 5G, 6G) 4T4R 802.11be Wi-Fi
* Airoha AG3352 GPS
* Renesas DA14531MOD Bluetooth
* 2 buttons (Reset, Mesh/WPS)
* uC-controlled RGB LED via I2C
* 2x LED for each 1G port, 3x LED for each 10G port
* USB 3.0 type A port
* 3.3V-level 115200 baud UART console via 4-pin Dupont connector
exposed at the bottom of the device
* USB-C PD power input
SDG-8733: 1x 10000M/1000M/100M WAN port
SDG-8734: 1x USXGMII/10GBase-R/5GBase-R/2500Base-X/1000Base-X/SGMII SFP+
Both models are also available in versions including 2x FXS POTS interfaces
for analog phones. Those interfaces are not supported by OpenWrt.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add missing call to emmc_copy_config which either writes the sysupgrade
tar.gz backup file or clears the existing rootfs_data overlay.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Backport patch adding support for the AQR114C PHY and add support for
PHY LEDs and polarity setting of Aquantia 3rd and 4th generation PHYs.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Carambola3 is a WiFi module based on Qualcomm/Atheros QCA4531
http://wiki.8devices.com/carambola3
Specification:
- 650/600/216 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 32 MB of FLASH
- 2T2R 2.4 GHz
- 2x 10/100 Mbps Ethernet
- 1x USB 2.0 Host socket
- UART for serial console
- 12x GPIO
Flash instructions:
Upgrading from ar71xx target:
- Upload image into the board:
scp openwrt-ath79-generic-8dev_carambola3-squashfs-sysupgrade.bin \
root@192.168.1.1/tmp/
- Run sysupgrade
sysupgrade -F /tmp/openwrt-ath79-generic-8dev_carambola3-squashfs-sysupgrade.bin
Upgrading from u-boot:
- Set up tftp server with openwrt-ath79-generic-8dev_carambola3-initramfs-kernel.bin
- Go to u-boot (reboot and press ESC when prompted)
- Set TFTP server IP
setenv serverip 192.168.1.254
- Set device ip from the same subnet
setenv ipaddr 192.168.1.1
- Copy new firmware to board
tftpboot 0x82000000 initramfs.bin
- Boot OpenWRT
bootm 0x82000000
- Upload image openwrt-ath79-generic-8dev_carambola3-squashfs-sysupgrade.bin into the board
- Run sysupgrade.
Signed-off-by: Andrey Bondar <a.bondar@8devices.com>
Link: https://github.com/openwrt/openwrt/pull/15514
Signed-off-by: Robert Marko <robimarko@gmail.com>
Specifications:
CPU: MT7628AN 580MHz
RAM: 64MB DDR2
FLASH: 8MB EN25QH64 NOR SPI
WIFI: 2.4GHz 2x2 MT7628 b/g/n internal
WIFI: 5GHz 1x1 MT7610E ac/n PCI
LTE: Qualcomm MDM9207
ETH: 4xLAN 100base-T integrated
SWITCH: RT3050-ESW Port 0,1,2,3: LAN, Port 6: CPU
LEDS: LAN, WAN, Power, 3x signal strength, WiFi
BTNS: Reset, WiFi toggle
UART: Near ETH ports, Vcc-GND-RX-TX, 115200, 8N1
Installation:
1. Update using recovery mode
- set your IP to 192.168.0.225, subnet mask: 255.255.255.0
- start tftp server, rename tftp-recovery.bin to
tp_recovery.bin and place it into the server's directory
- while holdig the "reset" button, power on the device
- keep holding "reset" until the file is being transferred
Notes:
This board has only one MAC address programmed
in the "romfile" partition:
- MAC for phy0 (2.4GHz) at romfile 0xf100 (0)
- MAC for phy1 (5GHz) at romfile 0xf100 (-1)
- stock firmware re-uses phy0 MAC for ethernet
- stock firmware uses romfile 0xf100 (1) for WWAN;
not used since QMI interface is raw IP
Signed-off-by: Lea Teuberth <lea.teuberth@outlook.com>
mt7915e driver supports MT7915 & MT7916 devices and MT7981 & MT7986
on-SoC wireless controllers. Devices based on MT7988 and possibly other
next chipsets are quite unlikely to need it (MT7988 was designed to be
used with MT7996).
Move kmod-mt7915e to DEVICE_PACKAGES of relevant devices.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Currently, in case that PSGMII calibration fails it will panic the kernel
which is not ideal and is preventing any debugging to be done.
So, since PGMII calibration failing only means that wired networking wont
work lets convet the panic() call to dev_error.
Link: https://github.com/openwrt/openwrt/pull/15542
Signed-off-by: Robert Marko <robimarko@gmail.com>
This commit adds support for Netgear Orbi Pro SXR80 and SXS80 (collectively known as SXK80)
Specifications:
---------------
* CPU: Qualcomm IPQ8074A Quad core Cortex-A53
* RAM: 1024MB
* Storage: SPI-NAND 512 MiB (Winbond W29N04GZ)
* Ethernet: 4x 1G RJ45 ports (QCA8075) 1x 2.5G RJ45 LAN/WAN (QCA8081)
* WLAN:
- 2.4 GHz: Qualcomm QCN5024 4x4
- 2x 5 GHz: Qualcomm QCN5054 4x4 (second radio high channels only)
* LEDs:
- Power: (Green and red)
- Front: (Blue, green, red and white)
* Buttons:
- 1x Soft reset
- 1x Sync/WPS
* Power: 12V DC Jack
Installation instructions (Telnet):
-----------------------------------
*Note, this guide assumes SXR80, for SXS80 change the firmware file name as appropriate
1. Put firmware file openwrt-qualcommax-ipq807x-netgear_sxr80-initramfs-uImage.itb in root of TFTP server available at 192.168.1.10.
2. Enable telnet by going to http://[ip of device]/debug.htm and clicking on the tickbox 'Enable telnet'
3. Telnet into the device and login using the same username and password as the web interface:
4. Run the following command:
`fw_setenv bootcmd 'env default -a; saveenv; reset'`
5. Reboot the router, once the web interface is available again re-enable telnet via http://[ip of device]/debug.htm and telnet into the device.
6. Run the following command:
`fw_printenv`
It should look similar to the below:
```
baudrate=115200
bootargs=console=ttyMSM0,115200n8
bootcmd=mii write 0x0 0x0 0x800; sleep 1; nmrp; bootdni; boot_DNI_secureboot
bootdelay=2
ipaddr=192.168.1.1
netmask=255.255.255.0
serverip=192.168.1.10
soc_version_major=2
soc_version_minor=0
```
**If you see the message:**
`Warning: Bad CRC, using default environment`
**DO NOT CONTINUE, YOU WILL BRICK YOUR DEVICE**
7. Run the following command:
`fw_setenv originalboot 'mii write 0x0 0x0 0x800; sleep 1; nmrp; bootdni; boot_DNI_secureboot'`
(This should match what's in the bootcmd variable displayed in step 6)
8. Run the following commands:
```
fw_setenv wrttftp 'mii write 0x0 0x0 0x800; sleep 1; nmrp; if tftpboot openwrt-qualcommax-ipq807x-netgear_sxr80-initramfs-uImage.itb; then bootm; fi; bootdni; boot_DNI_secureboot'
fw_setenv wrtboot 'mii write 0x0 0x0 0x800; sleep 1; nmrp; nand read 0x40000000 0x1980000 0x06d00000; bootm 0x40000000'
fw_setenv bootcmd 'run wrttftp'
```
9. Ensure SXR/S device is attached via ethernet (LAN port) to the same ethernet segment as the TFTP server.
10. Reboot the device, it should reboot into OpenWrt and be available on 192.168.1.1
11. Once OpenWrt has booted, update the bootcmd using the following command:
`fw_setenv bootcmd 'run wrtboot'`
12. Flash the sysupgrade image
13. It should boot into OpenWrt
References to SXK80 GPL source:
https://www.downloads.netgear.com/files/GPL/SXK80-V3.2.0.108_gpl_src.tar.bz2.zip
Signed-off-by: Flole Systems <flole@flole.de>
Signed-off-by: Andrew Smith <gul.code@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/14939
Signed-off-by: Robert Marko <robimarko@gmail.com>
It seems that on Spectrum SAX1V1K QCA8081 is being brought out of reset
too quickly and thus causing it to get stuck in an invalid autoneg
register configuration mode.
Setting an deasset delay seems to fix this, so lets set it.
Fixes: #15493
Link: https://github.com/openwrt/openwrt/pull/15541
Signed-off-by: Robert Marko <robimarko@gmail.com>
filogic: Add support for D-Link AQUILA PRO AI M30
Specification:
- MT7981 CPU using 2.4GHz and 5GHz WiFi (both AX)
- 1GB RAM
- 16MB NOR
- 128MB NAND
- 3 LEDs (red, green, blue, white)
- 2 buttons (reset, user defined)
- 1 2.5Gbit WAN port (Airoha EN8811h)
- 1 1Gbit LAN ports
- 1 single lane M.2 SSD slot
- 1 mikroBus socket
- externel HW WDT (25s refresh time)
- i2c RTC (with battery backup)
Serial Interface
- UBS-C CDC-ACM
- 3 Pins GND, RX, TX
- Settings: 115200, 8N1
MAC addresses are not populated on the early samples.
Signed-off-by: John Crispin <john@phrozen.org>
The IXP4xx is well supported upstream and can readily be
supported with kernel v6.6. To simplify things after the
DTS directory was renamed, switch to v6.6 only.
Bring in some outstanding patches.
Tested on the Gateworks GW2348-4.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
These patches have partial acceptance upstream and are still
a WIP, now there is merge window for kernel v6.10 so these
will not be reposted until that is over. In the meantime,
let's add the current state to OpenWrt so the ethernet on
Gemini is up and working (tested on several devices).
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix multiple issue with manifest handling where APK was hardcoded
and fix a logic error where (TODO) APK _check_keys was called for the
OPKG codepath instead of correctly calling for the APK codepath.
Fixes: d788ab376f ("build: add APK package build capabilities")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add ubi volumes for mt7988a-rfb and support for using factory data
for Ethernet MAC addresses and MT7996 WLAN calibration data.
Also add rootdisk handle. Removes the need to keep using nmbm
Signed-off-by: Felix Fietkau <nbd@nbd.name>
A new option called `USE_APK` is added which generated APK packages
(.apk) instead of OPKG packages (.ipk).
Some features like fstools `snapshot` command are not yet ported
Signed-off-by: Paul Spooren <mail@aparcar.org>
Without serial or network access the only option for initial
configuration, is a attached display with USB keyboard, but the keyboard
driver needs to be installed first. So enable keyboard driver by default
to avoid this issue.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Because recent changes to procd, last "console" argument was used as
primary argument and causing no terminal to be spawned on serial
interface. So drop the hardcoded consoles in boot script, since dts has
already an alias specified, which lets procd decide where to spawn the
terminal.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
The old overlay remained after upgrades and would cause failure on first
boot after upgrade, in which no new overlay could be created while old
one was unusable.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Hardware specification:
========
SoC: Qualcomm IPQ8072A
Flash: 512MB (Fidelix FMND4G08S3J-ID)
RAM: 1GB (2x Kingston DDR3L D2516ECMDXGJD)
Ethernet: 1x 10/100/1000/2500/5000Mbps (Marvell AQR114C)
Ethernet: 4x 10/100/1000Mbps (Qualcomm QCA8075)
WiFi1: 6GHz ax 4x4 (Qualcomm QCN9024 + Skyworks SKY85784-11) - channels 33-229
WiFi2: 5GHz ax 4x4 (Qualcomm QCN5054 + Skyworks SKY85755-11) - channels 36-177
WiFi3: 2.4GHz ax 4x4 (Qualcomm QCN5024 + Skyworks SKY8340-11)
IoT: Bluetooth 5, Zigbee and Thread (NXP K32W041)
LED: 1x RGB status (NXP PCA9633)
USB: 1x USB 3.0
Button: WPS, Reset
Flash instructions:
========
1. Manually upgrade firmware using openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin image.
More details can be found here: https://www.linksys.com/support-article?articleNum=47547
After first boot check actual partition:
- fw_printenv -n boot_part
and install firmware on second partition using command in case of 2:
- mtd -r -e kernel -n write openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin kernel
and in case of 1:
- mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin alt_kernel
2. Installation using serial connection from OEM firmware (default login: root, password: admin):
- fw_printenv -n boot_part
In case of 2:
- flash_erase /dev/mtd21 0 0
- nandwrite -p /dev/mtd21 openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin
or in case of 1:
- flash_erase /dev/mtd23 0 0
- nandwrite -p /dev/mtd23 openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin
After first boot install firmware on second partition:
- mtd -r -e kernel -n write openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin kernel
or:
- mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin alt_kernel
3. Installation from initramfs image using USB drive:
Put the initramfs image on the USB drive:
- dd bs=1M if=openwrt-qualcommax-ipq807x-linksys_mx8500-initramfs-uImage.itb of=/dev/sda
Stop u-boot and run:
- usb start && usbboot $loadaddr 0 && bootm $loadaddr
Write firmware to the flash from initramfs:
- mtd -e kernel -n write openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin kernel
and:
- mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin alt_kernel
4. Back to the OEM firmware:
- mtd -e kernel -n write FW_MX8500_1.0.11.208937_prod.img kernel
and:
- mtd -r -e alt_kernel -n write FW_MX8500_1.0.11.208937_prod.img alt_kernel
5. USB recovery:
Put the initramfs image on the USB:
- dd bs=1M if=openwrt-qualcommax-ipq807x-linksys_mx8500-initramfs-uImage.itb of=/dev/sda
Set u-boot env:
- fw_setenv bootusb 'usb start && usbboot $loadaddr 0 && bootm $loadaddr'
- fw_setenv bootcmd 'run bootusb; if test $auto_recovery = no; then bootipq; elif test $boot_part = 1; then run bootpart1; else run bootpart2; fi'
AQR firmware:
========
1. Firmware loading:
To properly load the firmware and initialize AQR PHY, we must use the u-boot aq_load_fw function.
To do this, you need to modify u-boot env:
With USB recovery:
- fw_setenv bootcmd 'aq_load_fw; run bootusb; if test $auto_recovery = no; then bootipq; elif test $boot_part = 1; then run bootpart1; else run bootpart2; fi'
and without:
- fw_setenv bootcmd 'aq_load_fw; if test $auto_recovery = no; then bootipq; elif test $boot_part = 1; then run bootpart1; else run bootpart2; fi'
2. Firmware updating:
Newer firmware (AQR-G4_v5.6.5-AQR_WNC_SAQA-L2_GT_ID45287_VER24005.cld) is available in the latest OEM firmware.
To load this firmware via u-boot, we need to add the MBN header and update 0:ethphyfw partition.
For MBN header we can use script from this repository: https://github.com/testuser7/aqr_mbn_tool
- python aqr_mbn_tool.py AQR-G4_v5.6.5-AQR_WNC_SAQA-L2_GT_ID45287_VER24005.cld
To update partition we need to install kmod-mtd-rw package first:
- insmod mtd-rw.ko i_want_a_brick=1
- mtd -e /dev/mtd26 -n write aqr_fw.mbn /dev/mtd26
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/14883
Signed-off-by: Robert Marko <robimarko@gmail.com>
Define common Linksys MX device for MX4200v1/v2 and MX5300.
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/14883
Signed-off-by: Robert Marko <robimarko@gmail.com>
Remove gpio16 from the default NAND pinctrl configuration
as its unused and only needed for LCD.
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/14883
Signed-off-by: Robert Marko <robimarko@gmail.com>
All three PCIe ports are reported non working on Meraki MR42/MR52 boards
since kernel 6.1 with the issue of PCIe PHY link never coming up thus
no WLAN cards are available on the boards.
After debugging it seems that PCIe worked on 5.15 and older purely by
accident as device DTS was using /delete-property/ perst-gpios; in each
of the 3 PCIe nodes but there was no "perst-gpios" property in the SoC DTSI
as it was still using the older "perst-gpio" property so it was not getting
removed from the device DTS.
However, in kernel 6.1 commit ("ARM: dts: qcom-*: replace deprecated
perst-gpio with perst-gpios") updated all Qualcomm DTS-es to use the newer
"perst-gpios" and thus once ipq806x moved to 6.1 PCIe stopped working as
now that property was being dropped from the device DTS.
So, since the removal of PERST pins seems to have been wrong from the start
lets drop the property removal from MR42/MR52.
Fixes: #15408
Link: https://github.com/openwrt/openwrt/pull/15509
Signed-off-by: Robert Marko <robimarko@gmail.com>
Our kernel export stripping has been broken on 6.6 from the start since
upstream kernel really reworked stuff in ("kbuild: generate KSYMTAB entries
by modpost") and other commits as well.
So, until this is either fixed or reworked lets drop the patch as it doesnt
make sense to carry it knowing its broken and it can always be easily
restored.
Link: https://github.com/openwrt/openwrt/pull/15498
Signed-off-by: Robert Marko <robimarko@gmail.com>
This code assumed that the mt7628an_tplink_8m.dtsi file defines
mediatek,mtd-eeprom for the wmac and sets status to okay.
The mediatek,mtd-eeprom definition was removed in commit e93f41adee
("ramips: convert MT7628 EEPROM to NVMEM format") but the dts for these
two devices was not adapted to include the eeprom position on its own.
The status = "okay" property was removed in 0a1d15642f ("ramips:
mt7628: use nvmem-layout"), but the property was not added to these dts
files.
Without this change wifi does not work for these devices.
Fixes: e93f41adee ("ramips: convert MT7628 EEPROM to NVMEM format")
Fixes: 0a1d15642f ("ramips: mt7628: use nvmem-layout")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Linux kernel commit 90c2d2eb7ab5 ("MIPS: pci: lantiq: switch to using
gpiod API") not only switched to the gpiod API, but also inverted /
changed the polarity of the GPIO.
According to the PCI specification, the RST# pin is an active-low
signal. However, most of the device trees that have been widely used for
a long time (mainly in the openWrt project) define this GPIO as
active-high and the old driver code inverted the signal internally.
Apparently there are actually boards where the reset gpio must be
operated inverted. For this reason, we cannot use the GPIOD_OUT_LOW/HIGH
flag for initialization. Instead, we must explicitly set the gpio to
value 1 in order to take into account any "GPIO_ACTIVE_LOW" flag that
may have been set.
In order to remain compatible with all these existing device trees, we
should therefore keep the logic as it was before the commit.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
This is required for linux-6.1 compatibility.
IRQs are not automatically mapped from HW to virtual IRQ numbers when
the IRQ domain is registered. This happens when the IRQ number is read
from the device tree based on the IRQ domain from the device tree now.
In kernel 5.15 it was done when the IRQ domain was registered.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
This is required for linux-6.1 compatibility.
IRQs are not automatically mapped from HW to virtual IRQ numbers when
the IRQ domain is registered. This happens when the IRQ number is read
from the device tree based on the IRQ domain from the device tree now.
In kernel 5.15 it was done when the IRQ domain was registered.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
This is required for linux-6.1 compatibility.
IRQs are not automatically mapped from HW to virtual IRQ numbers when
the IRQ domain is registered. This happens when the IRQ number is read
from the device tree based on the IRQ domain from the device tree now.
In kernel 5.15 it was done when the IRQ domain was registered.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Use dev_err_probe() to get rid of the following warning which is
seen when the PCIe PHY has not been probed yet:
pcie-xrx200 1d900000.pcie: failed to get the PCIe PHY
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
This backports some patches for the gswip switch driver.
I copied them from this repository:
https://github.com/xdarklight/linux/commits/lantiq-gswip-integration-20221022
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
[drop some patches which may break functionality at the moment]
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
If the reverted timer driver fails to allocate interrupts handle the
error better.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
[moved printk before the cleanup for-loop]
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Make all the patches apply and delete the ones already integrated into
upstream Linux kernel. This also refreshes some of the kernel
configurations.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
[refreshed for linux 6.1.89]
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
This is an automatically generated commit which aids following Kernel patch
history, as git will see the move and copy as a rename thus defeating the
purpose.
For the original discussion see:
https://lists.openwrt.org/pipermail/openwrt-devel/2023-October/041673.html
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
This refreshes the configuration for Linux kernel 5.15.
I first selected the xrx200 subtarget and then refreshed the target
kernel configuration using this command:
make kernel_oldconfig CONFIG_TARGET=target
Then I selected one subtarget after the other and refreshed their
configuration using this command:
make kernel_oldconfig CONFIG_TARGET=subtarget
I compared the kernel configuration used to compile the kernel from the
build directory for each subtarget before and after this task and it was
still the same.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
[refreshed config for linux 5.15.158]
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
There is a custom LED controller between the 3 SoC GPIO outputs and
the red and blue LEDs of the device. It implements a strange mapping
that includes fixed, flashing, and breathing modes.
The current DTS configuration causes OpenWrt to flash the LEDs over
the controller's own flashing, resulting in chaotic output in boot,
failsafe, and upgrade modes.
This change fixes the LEDs in the best way possible as long as each
OpenWrt running state is limited to be signaled by a single led.
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15440
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
There is no need to use 'list_for_each_entry_safe' here, as nothing is
removed from the list in the 'for' loop.
Use 'list_for_each_entry' instead, it is slightly less verbose.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://github.com/openwrt/openwrt/pull/15435
Link: https://github.com/openwrt/openwrt/pull/15435
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Fixes the issue of RTL8221B-VB-CG not being detected correctly.
Reverts changes from f6c27b2, leaving only the read_c45 test.
Fixed: #15093
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Lets give Linux 6.6 a try.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://github.com/openwrt/openwrt/pull/15416
Signed-off-by: Robert Marko <robimarko@gmail.com>
Refresh kernel config for Linux 6.6.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://github.com/openwrt/openwrt/pull/15416
Signed-off-by: Robert Marko <robimarko@gmail.com>
Refresh the only remaining downstream patch.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://github.com/openwrt/openwrt/pull/15416
Signed-off-by: Robert Marko <robimarko@gmail.com>
This is an automatically generated commit.
When doing `git bisect`, consider `git bisect --skip`.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://github.com/openwrt/openwrt/pull/15416
Signed-off-by: Robert Marko <robimarko@gmail.com>
Update default kernel version to 6.6 and drop configs and patches for
kernel 6.1. We can also omit the conditional to include DTS dir.
Signed-off-by: Stefan Kalscheuer <stefan@stklcode.de>
Link: https://github.com/openwrt/openwrt/pull/15449
Signed-off-by: Robert Marko <robimarko@gmail.com>
Like AVM 1200 these devices also do not use QCA807x PHY at all and thus
they disables all of the individual PHY nodes, however this is not enough
anymore since the conversion to PHY package.
Now its now enough to disable the PHY-s in the package alone, but the PHY
package node itself must also be disabled.
Fixes: 1b931c33a2 ("ipq40xx: adapt to new Upstream QCA807x PHY driver")
Link: https://github.com/openwrt/openwrt/pull/15444
Signed-off-by: Robert Marko <robimarko@gmail.com>
- Soc: MediaTek MT7621AT
- RAM: 512 MB (DDR3)
- Flash: 16 MB (SPI NOR)
- WiFi: MediaTek MT7905DAN, MediaTek MT7975DN
- Ethernet: 1 WAN, 3 LAN (Gigabit)
- Buttons: Reset, Joylink
- LEDs: (red, blue, green), routed to one indicator in the top of the
device
- Power: DC 12V 1A tip positive
- 1 TF Card Slot
The pins for the serial console are already labeled on the board
J4(V, R, T, G). Serial settings: 3.3V, 115200
MAC addresses:
| | MAC | Algorithm |
| ------- | ----------------- | --------- |
| label | dc:d8:xx:xx:xx:01 | label |
| LAN | dc:d8:xx:xx:xx:01 | label |
| WAN | dc:d8:xx:xx:xx:02 | label+1 |
| WLAN 2g | dc:d8:xx:xx:xx:03 | label+2 |
| WLAN 5g | de:d8:xx:xx:xx:04 | label+3 |
1. rename the
openwrt-ramips-mt7621-jdcloud_re-cp-02-squashfs-sysupgrade.bin
to JDCOS.bin
2. start a TFTP server from IP address 192.168.68.10 and serve the
image named JDCOS.bin
3. connect your device to the LAN port
4. power up the router and press any key on the console to interrupt
the boot process.
5. enter the following commands on the router console
1. setenv bootcount 6
2. saveenv
3. reset
> NOTE: wait for the restart, it will automatically fetch the
> image named JDCOS.bin from the TFTP server and write it into
> the flash. After the writing is completed, the router will be
> automatically restarted.
Unable to recognize large-capacity TF card, see #14042. But the patch
https://github.com/openwrt/openwrt/issues/14042#issuecomment-1910769942
works
Co-Authored-By: Jianti Chen <clbcjt@outlook.com>
Signed-off-by: Sheng Huang <shenghuang147@gmail.com>
Hardware:
SoC: MT7981b
RAM: 256 MB
Flash: 128 MB SPI NAND
Ethernet:
1x 2.5Gbps (rtl8221b)
1x 1Gbps (integrated phy)
WiFi: 2x2 MT7981
Buttons: Reset, WPS
LED: 1x multicolor
Solder on UART:
- remove rubber ring on the bottom
- remove screws
- pull up the cylinder, maybe help by push on an ethernet socket with a screwdriver
- remove the (3) screws holding the board in the frame
- remove the board from the frame to get to the screws for the silver, flat heat shield
- remove the (3) screws holding the heat shield
- solder UART pins to the back of the board
- make sure to have the pins point out on side with the black, finned heat spread
- the markings for the pins are going to be below the silver heat shield
- Vcc is not needed
If you don't intend on using the UART outside of the installation process, you might not
want to solder:
- carefully scrape off the thin layer of epoxy on the holes (not the copper)
- place your pin header with the UART attached in the holes
- the pins, starting with the one closest to the socket:
- Vcc (not required)
- GND
- RX
- TX
- either wedge the header or hold it with your fingers so that the pins stay in contact with the board
Installation (UART):
- attach an Ethernet cable to the 1Gbps port (black) on the router
- hold the reset button while powering the router
- press CTRL-C or wait for the timeout to get to the U-Boot prompt
- prepare a TFTP server on the network to supply ..-initramfs-kernel.bin
- use 'tftpboot' in the U-Boot shell to pull the image
- boot the image using 'bootm'
- push the ..-sysupgrade to the router using your preferred method
- perform the upgrade with 'sysupgrade -n'
There is a recovery mechanism that involves fetching a file called 'recovery.bin' but that is not understood yet.
Signed-off-by: Leon M. Busch-George <leon@georgemail.eu>
FCC ID: A8J-EWS660AP
Engenius ENS1750 is an outdoor wireless access point with
2 gigabit ethernet ports, dual-band wireless,
internal antenna plates, and 802.3at PoE+
Engenius EWS660AP, ENS1750, and ENS1200 are "electrically identical,
different model names are for marketing purpose" according to docs
provided by Engenius to the FCC.
**Specification:**
- QCA9558 SOC 2.4 GHz, 3x3
- QCA9880 WLAN mini PCIe card, 5 GHz, 3x3, 26dBm
- AR8035-A PHY RGMII GbE with PoE+ IN
- AR8033 PHY SGMII GbE with PoE+ OUT
- 40 MHz clock
- 16 MB FLASH MX25L12845EMI-10G
- 2x 64 MB RAM
- UART at J1 populated, RX grounded
- 6 internal antenna plates (5 dbi, omni-directional)
- 5 LEDs, 1 button (power, eth0, eth1, 2G, 5G) (reset)
**MAC addresses:**
Base MAC addressed labeled as "MAC"
Only one Vendor MAC address in flash
eth0 *:d4 MAC art 0x0
eth1 *:d5 --- art 0x0 +1
phy1 *:d6 --- art 0x0 +2
phy0 *:d7 --- art 0x0 +3
**Serial Access:**
the RX line on the board for UART is shorted to ground by resistor R176
therefore it must be removed to use the console
but it is not necessary to remove to view boot log
optionally, R175 can be replaced with a solder bridge short
the resistors R175 and R176 are next to the UART RX pin
**Installation:**
2 ways to flash factory.bin from OEM:
Method 1: Firmware upgrade page:
OEM webpage at 192.168.1.1
username and password "admin"
Navigate to "Firmware Upgrade" page from left pane
Click Browse and select the factory.bin image
Upload and verify checksum
Click Continue to confirm and wait 3 minutes
Method 2: Serial to load Failsafe webpage:
After connecting to serial console and rebooting...
Interrupt uboot with any key pressed rapidly
execute `run failsafe_boot` OR `bootm 0x9fd70000`
wait a minute
connect to ethernet and navigate to
"192.168.1.1/index.htm"
Select the factory.bin image and upload
wait about 3 minutes
**Return to OEM:**
If you have a serial cable, see Serial Failsafe instructions
otherwise, uboot-env can be used to make uboot load the failsafe image
ssh into openwrt and run
`fw_setenv rootfs_checksum 0`
reboot, wait 3 minutes
connect to ethernet and navigate to 192.168.1.1/index.htm
select OEM firmware image from Engenius and click upgrade
**TFTP recovery:**
Requires serial console, reset button does nothing
rename initramfs.bin to '0101A8C0.img'
make available on TFTP server at 192.168.1.101
power board, interrupt boot
execute tftpboot and bootm 0x81000000
**Format of OEM firmware image:**
The OEM software of ENS1750 is a heavily modified version
of Openwrt Kamikaze. One of the many modifications
is to the sysupgrade program. Image verification is performed
simply by the successful ungzip and untar of the supplied file
and name check and header verification of the resulting contents.
To form a factory.bin that is accepted by OEM Openwrt build,
the kernel and rootfs must have specific names...
openwrt-ar71xx-generic-ens1750-uImage-lzma.bin
openwrt-ar71xx-generic-ens1750-root.squashfs
and begin with the respective headers (uImage, squashfs).
Then the files must be tarballed and gzipped.
The resulting binary is actually a tar.gz file in disguise.
This can be verified by using binwalk on the OEM firmware images,
ungzipping then untaring.
Newer EnGenius software requires more checks but their script
includes a way to skip them, otherwise the tar must include
a text file with the version and md5sums in a deprecated format.
The OEM upgrade script is at /etc/fwupgrade.sh.
OKLI kernel loader is required because the OEM software
expects the kernel to be no greater than 1536k
and the factory.bin upgrade procedure would otherwise
overwrite part of the kernel when writing rootfs.
Note on PLL-data cells:
The default PLL register values will not work
because of the external AR8035 switch between
the SOC and the ethernet port.
For QCA955x series, the PLL registers for eth0 and eth1
can be see in the DTSI as 0x28 and 0x48 respectively.
Therefore the PLL registers can be read from uboot
for each link speed after attempting tftpboot
or another network action using that link speed
with `md 0x18050028 1` and `md 0x18050048 1`.
The clock delay required for RGMII can be applied
at the PHY side, using the at803x driver `phy-mode`.
Therefore the PLL registers for GMAC0
do not need the bits for delay on the MAC side.
This is possible due to fixes in at803x driver
since Linux 5.1 and 5.3
Tested-by: Kevin Abraham <kevin@westhousefarm.com>
Signed-off-by: Kevin Abraham <kevin@westhousefarm.com>
Add additional PWM fan cooling step and enable fan on BPi-R4.
Suggested-by: Frank Wunderlich <frank-w@public-files.de>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
We should setup the registers for trapping LLDP packets to the CPU.
Currently, these packets are forwarded to all ports which is not desired
behaviour.
Signed-off-by: Kevin Jilissen <info@kevinjilissen.nl>
These registers control the handling of Link Layer Discovery Protocol
(LLDP) packets. This seems to be a typo in the naming.
Signed-off-by: Kevin Jilissen <info@kevinjilissen.nl>
This device is similiar to the Wavlink WL-WN531A3.
Hardware
--------
SoC: Mediatek MT7620A
RAM: 64MB
FLASH: 8MB NOR (GigaDevice GD25Q64CS)
ETH:
- 2x 10/100/1000 Mbps Ethernet (RTL8211F)
- 3x 10/100 Mbps Ethernet (integrated in SOC)
WIFI:
- 2.4GHz: 1x (integrated in SOC) (2x2:2)
- 5GHz: 1x MT7612E (2x2:2)
- 4 external antennas
BTN:
- 1x Reset button
- 1x Touchlink button
- 1x Turbo button
- 1x Wps button
- 1x ON/OFF switch
LEDS:
- 1x Red led (system status)
- 1x Blue led (system status)
- 5x Blue leds (ethernet ports)
- 1x Power led
- 1x Wifi led
UART:
- 57600-8-N-1
Everything works correctly.
Installation
------------
Flash the initramfs image in the OEM firmware interface
When Openwrt boots, flash the sysupgrade image otherwise you won't be
able to keep configuration between reboots.
In my case the whole device was locked and there was no way
to flash the image, except for flashing directly to the flash
via an spi-flasher. You need to put the sysupgrade image file at
the beginning of 0x60000.
Notes
-----
1) Router mac addresses:
LAN XX:XX:XX:XX:XX:F0 (factory @ 0x28)
WAN XX:XX:XX:XX:XX:F1 (factory @ 0x2e)
WIFI 2G XX:XX:XX:XX:XX:F2 (factory @ 0x04)
WIFI 5G XX:XX:XX:XX:XX:F3 (factory @ 0x8004)
LABEL XX:XX:XX:XX:XX:F2
Signed-off-by: Eros Brigmann <erosbrigmann@gmail.com>
All kernel config files are refreshed by
`make kernel_oldconfig CONFIG_TARGET={subtarget_target,subtarget}`
"CONFIG_SQUASHFS_DECOMP_SINGLE=y" is manually selected as all ath79
SoCs are single core processors.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
The upcoming 6.6 kernel will introduce a new upstream generic
"gpio-latch" driver. It will conflict with the downstream MikroTik
GPIO latch driver. Let's rename it to avoid any potential issues.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Hardware:
- SoC: MediaTek MT7981B
- CPU: 2x 1.3 GHz Cortex-A53
- Flash: 128 MiB SPI NAND
- RAM: 512 MiB
- WLAN: 2.4 GHz, 5 GHz (MediaTek MT7976CN, 802.11ax)
- Ethernet: 1x 10/100/1000/2500 Mbps RTL8221B WAN, 1x10/100/1000 Mbps MT7981 LAN
- USB 3.0 port
- Buttons: 1 Reset button, 1 slider button
- LEDs: 1x Red, 1x White
- Serial console: internal test points, 115200 8n1
- Power: 5 VDC, 3 A
MAC addresses:
+---------+-------------------+-----------+
| | MAC | Algorithm |
+---------+-------------------+-----------+
| WAN | 80:af:ca:xx:xx:x1 | label+1 |
| LAN | 80:af:ca:xx:xx:x0 | label |
| WLAN 2g | 80:af:ca:xx:xx:x0 | label |
| WLAN 5g | 82:af:ca:xx:xx:x0 | |
+---------+-------------------+-----------+
Installation:
The installation must be done via TFTP by disassembling the router. On other occasions Cudy has distributed intermediate firmware to make installation easier, and so I recommend checking the Wiki for this device if there is a more convenient solution than the one below.
To install using TFTP:
1. Connect to UART.
2. With the router off, press the RESET button. While the router is turning on, the button should continue to be pressed for at least 5 seconds.
3. A u-boot shell will automatically open.
4. Connect to LAN and set your IP to 192.168.1.88/24. Configure a TFTP server and an OpenWrt initramfs-kernel.bin firmware file.
5. Run these steps in u-boot using the name of your file.
setenv bootfile initramfs-kernel.bin
tftpboot
bootm
6. If you can reach LuCI or SSH now, just use the sysupgrade image with the 'Keep settings' option turned off.
Signed-off-by: Luis Mita <luis@luismita.com>
Hardware Specification:
SoC: Mediatek MT7621DAT (MIPS1004Kc 880 MHz, dual core)
RAM: 128 MB
Storage: 128 MB NAND flash
Ethernet: 5x 10/100/1000 Mbps LAN1,LAN2,LAN3,LAN4 & WAN
Wireless: 2.4GHz: Mediatek MT7603EN up to 300Mbps (802.11b/g/n MIMO 2x2)
Wireless: 5GHz: Mediatek MT7615N up to 1733Mbps (802.11n/ac MU-MIMO 4x4)
LEDs: Power (white & amber), Internet (white & amber)
LEDs: 2.4G (White), 5Ghz (White)
Buttons: WPS, Reset
MAC Table
Label xx:xx:xx:xx:xx:EB
LAN xx:xx:xx:xx:xx:EB
2.4Ghz xx:xx:xx:xx:xx:EC
5Ghz xx:xx:xx:xx:xx:ED
WAN xx:xx:xx:xx:xx:EE
Flash instructions:
D-Link normal OEM firmware update page
1. upload OpenWRT factory.bin like any D-Link upgrade image
D-Link Recovery GUI:
1. Push and hold reset button (on the bottom of the device) until power led starts flashing (about 10 secs or so) while plugging in the power cable.
2. Give it ~30 seconds, to boot the recovery mode GUI
3. Connect your client computer to LAN1 of the device
4. Set your client IP address manually to 192.168.0.2 / 255.255.255.0
5. Call the recovery page for the device at http://192.168.0.1/
6. Use the provided emergency web GUI to upload the recovery.bin to the device
Firefox on Windows in a Private Window (incognito) works me
Internet Explorer mode in Microsoft Edge works for others
seems to not work in Linux or virtual machine on Linux for most
some see success using 'curl -v -i -F "firmware=@file.bin" 192.168.0.1'
Thanks to @frkca and @rodneyrod for testing and pushing for its creation
Signed-off-by: Alan Luck <luckyhome2008@gmail.com>
Setting the LED name and abandoning the label and using the
function/color syntax for some TP-Link Archer series routers:
Archer C2 v1, Archer C20 v1, Archer C20i and Archer C50 v1
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Abandoning the label and using the function/color syntax for some dlink
dir series routers: dir-1960-a1, dir-2660-a1, dir-2640-a1, dir-3040-a1
and dir-3060-a1
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Rename from mt7621_dlink_dir-xx60-a1.dtsi to mt7621_dlink_dir_nand_128m.dtsi
and associated group name when creating the mt7621.mk image
Co-authored-by: Alan Luck <luckyhome2008@gmail.com>
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Continuation of commit 8b66f1a. Set the switch address on the MDIO bus to 31.
This is required for all boards currently working with the mt7530 DSA driver.
Fixes: #15419
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Backport patch merged upstream for rgmii-id support in stmmac-ipq806x.
This is needed for some device that directly connets PHY to the gmac
port and require rgmii-id phy-modes.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
WPJ419 is still manually defining SPI node, so lets
convert it to use the existing upstream labels for SPI node.
Link: https://github.com/openwrt/openwrt/pull/15415
Signed-off-by: Robert Marko <robimarko@gmail.com>
