This reverts commit 3bd2cee9bf.
Based on my testing, we are unable to control USB power supply
through some third-party tools (e.g. uhubctl) or sysfs in userspace.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/17339
Signed-off-by: Robert Marko <robimarko@gmail.com>
set macaddress correctly for board
Signed-off-by: Florian Maurer <f.maurer@outlook.de>
Link: https://github.com/openwrt/openwrt/pull/17305
Signed-off-by: Robert Marko <robimarko@gmail.com>
The blocksize was too high, resulting in forgetting the config on sysupgrade
It is not needed for SPI-NOR.
Signed-off-by: Florian Maurer <f.maurer@outlook.de>
Link: https://github.com/openwrt/openwrt/pull/17305
Signed-off-by: Robert Marko <robimarko@gmail.com>
The boards where renamed, but BUILD_DEVICES was not adapted. This
variable points to the board name. Without this change the u-boot
binaries are not selected in the configuration.
Copy the u-boot binaries under the BUILD_DEVICES name as it is expected
by the image scripts.
Fixes: 33e23e8922 ("build: d1: add SUPPORTED_DEVICES")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
No need to pass the option no-warn-rwx-segments. Since v2.12, TF-A
automatically selects it if needed.
A patch is added to revert commit 03a581e2 ("feat(stm32mp1-fdts): remove
RTC clock configuration").
This commit removed RTC clock configuration, as it assumed that it was done
correctly by OPTEE.
But it is not the case. Without this patch the RTC is in a bad state,
consequently the wifi module cannot be initialized.
stm32_rtc 5c004000.rtc: rtc_ck is slow
stm32_rtc 5c004000.rtc: Can't enter in init mode. Prescaler config failed.
stm32_rtc: probe of 5c004000.rtc failed with error -110
sdio mmc1:0001:1: Direct firmware load for brcm/brcmfmac43430-sdio.st,stm32mp135f-dk.bin failed with error -2
brcmfmac: brcmf_sdio_htclk: HT Avail timeout (1000000): clkctl 0x50
Tested on STM32MP135F-DK.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/17243
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Since v2.12, TF-A automatically selects the no-warn-rwx-segments option if
needed.
So move this hack to the package Makefiles.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/17243
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Now the tool mkeficapsule is built by default if EFI_LOADER config is set
(which is the case by default for armv7).
This tool needs gnutls, which only exists in the packages feed.
As we don't need mkeficapsule, just disable it.
Tested on STM32MP135F-DK.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/17243
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested on STM32MP135F-DK.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/17243
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tenbay WR3000K is an 802.11ax (Wi-Fi 6) router, based on MediaTek MT7981B.
- SoC: MetiaTek MT7981B
- RAM: Hynex H5TQ2G863GFR 512MiB
- Flash: Winbond W25N01GVZEIG 128MiB
- Wi-Fi: MediaTek MT7976C (2.4GHz/5GHz, 802.11ax, 2x2 MIMO, AX3000)
- MediaTek MT7915E: 2.4GHz and 5GHz
- Ethernet: 1x 10/100/1000 Mbps WAN + 3x 10/100/1000 Mbps LAN
- Switch: MediaTek MT7531AE
- UART: J4 (115200 baud)
- LEDs: Power
- Buttons: Reset, WPS
- PWR: 12V/1A DC, 5.5×2.1 connector
| Vendor | OpenWrt Interface | Address | Notes |
|---------|-------------------|---------------|------------------------------------------------|
| WAN | wan | Label MAC | Stored MAC in factory + offset 4, label MAC is Stored MAC - 2 |
| LAN | br-lan | Label MAC+1 | |
| 2.4GHz | phy0-ap0 | Label MAC + 2 | |
| 5GHz | phy1-ap0 | Label MAC + 3 | |
- 0x000000000000-0x000000100000 : "BL2"
- 0x000000100000-0x000000180000 : "u-boot-env"
- 0x000000180000-0x000000380000 : "Factory"
- 0x000000380000-0x000000580000 : "FIP"
- 0x000000580000-0x000003580000 : "ubi"
- 0x000003580000-0x000006580000 : "ubi1"
- 0x000006580000-0x0000065a0000 : "Product"
- 0x0000065a0000-0x000007580000 : "Custom"
- The original partition-Ubi partition-Ubi1 is an AB dual system, and Openwrt only uses Ubi. So flash requires modifying the uboot variable `boot_from=ubi` to ensure that it only starts from Ubi.
- The Product and Custom partitions are original and only exist to align with the original layout; they are not used by OpenWrt.
- id: 0, kernel
- id: 1, rootfs
- id: 2, rootfs_data
- **USB-to-TTL Serial Adapter** (e.g., CH340 or CP2102).
- **Dupont Wires** (male-to-male, 3 wires).
- **PC/Laptop** with a serial communication tool.
- Screwdriver (to open the router case).
1. **OpenWrt Firmware**:
- Download the appropriate `wr3000k-<build_time>-mediatek-filogic-tenbay_wr3000k-squashfs-sysupgrade.bin` firmware file for your router from the [OpenWrt website](https://openwrt.org/).
2. **Serial Communication Tool**:
- Windows: PuTTY, Tera Term.
- Linux/Mac: Minicom, screen.
3. (Optional) **TFTP Server**:
- Install a TFTP server like Tftpd64 or tftp-hpa.
---
1. Open the router casing and locate the **TX, RX, and GND** pins.
2. Connect the router pins to the USB-to-TTL adapter as follows:
- **TX (router)** → **RX (adapter)**
- **RX (router)** → **TX (adapter)**
- **GND (router)** → **GND (adapter)**
3. Do **not** connect the VCC pin to avoid damage.
- **Baud rate**: 115200
- **Data bits**: 8
- **Stop bits**: 1
- **Parity**: None
- **Flow control**: None
---
1. Power on the router and observe the serial terminal output.
2. When prompted (e.g., `Hit any key to stop autoboot: 3`), press the '/' key quickly to interrupt the boot process.
3. You will see the U-Boot Boot Menu:
```plaintext
*** U-Boot Boot Menu ***
1. Factory mode
2. Startup system (Default)
3. Upgrade firmware
4. Upgrade ATF BL2
5. Upgrade ATF FIP
6. Upgrade single image
7. Load image
0. U-Boot console
Press UP/DOWN to move, ENTER to select, ESC/CTRL+C to quit
```
4. Select Option 0 by typing 0 and pressing Enter.
5. Input into
```plaintext
MT7981> setenv boot_from ubi
MT7981> saveenv
Saving Environment to MTD... Erasing on MTD device 'nmbm0'... OK
Writing to MTD device 'nmbm0'... OK
OK
MT7981> printenv
baudrate=115200
boot_from=ubi
...
```
the above indicates system will start from *ubi*.
and then type
```plaintext
MT7981> reset
```
will boot from *ubi*
1. Power on the router and observe the serial terminal output.
2. When prompted (e.g., `Hit any key to stop autoboot: 3`), press the '/' key quickly to interrupt the boot process.
3. You will see the U-Boot Boot Menu:
```plaintext
*** U-Boot Boot Menu ***
1. Factory mode
2. Startup system (Default)
3. Upgrade firmware
4. Upgrade ATF BL2
5. Upgrade ATF FIP
6. Upgrade single image
7. Load image
0. U-Boot console
Press UP/DOWN to move, ENTER to select, ESC/CTRL+C to quit
```
4. Choose Option 3: Upgrade Firmware
Enter Upgrade Mode
Select Option 3 by typing 3 and pressing Enter.
Upgrade Methods
You will be prompted to choose between:
```plaintext
*** Upgrading Firmware ***
Run image after upgrading? (Y/n): y
Available load methods:
0 - TFTP client (Default)
1 - Xmodem
2 - Ymodem
3 - Kermit
4 - S-Record
5 - RAM
Select (enter for default): 0
Input U-Boot's IP address: 192.168.1.1
Input TFTP server's IP address: 192.168.1.10
Input IP netmask: 255.255.255.0
Input file name: wr3000k-<build_time>-mediatek-filogic-tenbay_wr3000k-squashfs-sysupgrade.bin
```
Type Enter to proceed. The router will erase the old firmware and write the new one.
Signed-off-by: Jianyu Zhuang <xzjianyu@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17172
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hardware:
SoC: MT7981b
RAM: 512 MB
Flash: 256 MB SPI NAND
Ethernet:
1x2.5Gbps (rtl8221b)
WiFi: 2x2 MT7981
Button: Reset
LED: 1x multicolor
Installation
------------
At the moment, firmware installation is only possible via a transition firmware.
It's can be requested from the manufacturer by email to support@cudy.com
Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17225
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
`btusb` fails to start on MT7925 hardware without the appropriate
firmware being loaded first:
```
bluetooth hci0: Direct firmware load for mediatek/mt7925/BT_RAM_CODE_MT7925_1_1_hdr.bin failed with error -2
bluetooth hci0: Falling back to sysfs fallback for: mediatek/mt7925/BT_RAM_CODE_MT7925_1_1_hdr.bin
```
Package firmware for MediaTek MT7925 Bluetooth from `linux-firmware`.
Signed-off-by: Rani Hod <rani.hod@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17331
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The board has been redesigned due to previous hardware bugs
(with other reasons maybe).
Changes in new board:
- Added a gpio beeper
- Added a Atmel i2c eeprom
- Added a Atmel i2c ECC accelerator
- Added a Philips RTC module
- Added two RS485
- Removed WPS button
- Replaced USB3 port with M.2 B-key for LTE modules
- Swapped GbE LEDs gpio
Also assigned wifi mac with nvmem binding, added iface setup for failsafe,
increased phy assert time for rtl8221b, and updated LED labels.
Keeping compatibility for old version is not necessary here as only
few samples were sent to those interested in it.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/17253
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Package bnxt_en kernel module for Broadcom NetXtreme-C/E based Ethernet
network chips like BCM573xx and BCM574xx.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17301
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
4b849214b137 ipq8074: add TP-Link EAP620 HD v1 BDF Add board file for TP-Link EAP620 HD v1. Sourced from bdwlan_US.bin in stock firmware 1.1.0 Build 20211028
Signed-off-by: Shymon Samsel <ssamsel@umass.edu>
Link: https://github.com/openwrt/openwrt/pull/17254
Signed-off-by: Robert Marko <robimarko@gmail.com>
Specifications:
* SoC: Qualcomm IPQ8072A (64-bit Quad-core Arm Cortex-A53 @ 1.4 GHz)
* Memory: 2x ESMT M15T4G16256A-DEBG2G (1 GiB DDR3-1866 13-13-13)
* Serial Port: 3v3 TTL 115200n8
* Wi-Fi: QCA5054 (4x4 5 GHz 802.11ax)
* Wi-Fi: QCN5024 (2x2 2.4 GHz 802.11b/g/n/ax)
* Ethernet: AR8031 (10/100/1000BASE-T)
* Flash: Winbond W29N01HZSINF (128 MiB)
* LEDs: 1x Blue Status (GPIO 42 Active High)
* Buttons: 1x Reset (GPIO 50 Active Low)
Installation Instructions (Serial+TFTP):
1. Solder 4 pin header to JP1 and bridge pads of R58 and R62.
2. Connect 3V3 TTL port to TX, RX, and GND, which are positions 1, 2, and 3 respectively.
Be sure to crossover TX and RX.
3. Copy RAM firmware
openwrt-qualcommax-ipq807x-tplink_eap620hd-v1-initramfs-uImage.itb
to a TFTP server's root that is in the same subnet as your AP.
4. Power up the AP hold Ctrl+B in the serial console (115200n8) until autoboot is halted.
5. Run the following commands in the U-boot prompt:
# setenv serverip <TFTP server addr>
# setenv ipaddr <addr of AP>
# tftpboot 0x44000000 openwrt-qualcommax-ipq807x-tplink_eap620hd-v1-initramfs-uImage.itb
# bootm
You may need to type Ctrl+C and Enter before running these commands
to clear invisible characters from the buffer.
6. Run the following command in a terminal to copy the sysupgrade image
to be installed (check IP address):
$ scp -O openwrt-qualcommax-ipq807x-tplink_eap620hd-v1-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/
7. Activate the OpenWrt serial console and run the following commands:
# cd /tmp
# sysupgrade -n openwrt-qualcommax-ipq807x-tplink_eap620hd-v1-squashfs-sysupgrade.bin
8. The AP will reboot and OpenWrt will be successfully installed.
Known Issues:
* 5GHz radio instability (upstream current ath11k build bug maybe?)
Device support directly followed from EAP660HDv1 support
Links: #15832
Signed-off-by: Shymon Samsel <ssamsel@umass.edu>
Link: https://github.com/openwrt/openwrt/pull/17254
Signed-off-by: Robert Marko <robimarko@gmail.com>
In the process of upstreaming the local phy driver back in 2017, it
seems rt3050.dtsi was left out when updating the compatible string.
Add device reset as the driver needs it.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17257
Signed-off-by: Robert Marko <robimarko@gmail.com>
The dual-boot partition layout for the Zyxel GS1900 switches results in
6.9MB for both kernel and rootfs. Depending on the package selection,
this may already leave no space for the user overlay.
Merge the two firmware partitions, effectively dropping dual boot
support with OpenWrt. This results in a firmware partition of 13.9MB,
which should leave some room for the future.
To maintain install capabilites on new devices, an image is required
that still fits inside the original partition. The initramfs is used as
factory install image, so ensure this meets the old size constraints.
The factory image can be flashed via the same procedure as vendor images
when reverting to stock, can be installed from stock, or can be launched
via tftpboot.
Link: https://github.com/openwrt/openwrt/issues/16439
Link: https://github.com/openwrt/openwrt/pull/16442
Tested-by: Stijn Segers <foss@volatilesystems.org>
Signed-off-by: Sander Vanheule <sander@svanheule.net>
GPIO 5 on the RTL8231 is defined reset the system, but fails to actually
do so. This triggers a kernel a number of warnings and backtrace for
GPIO pins that can sleep, such as the RTL8231's. Two warnings are
emitted by libgpiod, and a third warning by gpio-restart itself after it
fails to restart the system:
[ 106.654008] ------------[ cut here ]------------
[ 106.659240] WARNING: CPU: 0 PID: 4279 at drivers/gpio/gpiolib.c:3098 gpiod_set_value+0x7c/0x108
[ Stack dump and call trace ]
[ 106.826218] ---[ end trace d1de50b401f5a153 ]---
[ 106.962992] ------------[ cut here ]------------
[ 106.968208] WARNING: CPU: 0 PID: 4279 at drivers/gpio/gpiolib.c:3098 gpiod_set_value+0x7c/0x108
[ Stack dump and call trace ]
[ 107.136718] ---[ end trace d1de50b401f5a154 ]---
[ 111.087092] ------------[ cut here ]------------
[ 111.092271] WARNING: CPU: 0 PID: 4279 at drivers/power/reset/gpio-restart.c:46 gpio_restart_notify+0xc0/0xdc
[ Stack dump and call trace ]
[ 111.256629] ---[ end trace d1de50b401f5a155 ]---
By removing gpio-restart from this device, we skip the restart-by-GPIO
attempt and rely only on the watchdog for restarts, which is already the
de facto behaviour.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Userspace handling is deprecated.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17311
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add the label-mac-device alias.
Signed-off-by: Fabian Bläse <fabian@blaese.de>
Link: https://github.com/openwrt/openwrt/pull/17313
Signed-off-by: Robert Marko <robimarko@gmail.com>
The AR8035 PHY is used in most Octeon boards supported by OpenWRT (all
the Ubiquiti routers at least). To be able to use its PHY-specific
functionality (cable testing, LED Control, ...) it should be built on
Octeon. It also needs the regulator framework, so enable that as well.
These boards are not space-constrained, so this really has no downsides.
Tested on an EdgeRouter Lite, cable tests now work with ethtool-full.
Signed-off-by: Lorenz Brun <lorenz@brun.one>
Link: https://github.com/openwrt/openwrt/pull/17318
Signed-off-by: Robert Marko <robimarko@gmail.com>
Fix the hexdump applet's formatting with certain format types
by applying the upstream fix for 1.37.0.
Also refresh patches.
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Link: https://github.com/openwrt/openwrt/pull/17308
[Changed to 002- patch file name prefix]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This backport patch inserted suspend/resume callbacks
for the wrong PHY driver.
The fixed patch is needed for Huawei AP5030DN
to initialize its second PHY.
Refresh all affected patch with make target/linux/refresh.
Fixes: 06cdc07f8c ("ath79: add support for Huawei AP5030DN")
Signed-off-by: Marco von Rosenberg <marcovr@selfnet.de>
Link: https://github.com/openwrt/openwrt/pull/17312
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Sets openwrt,netdev-name for the gmac nodes in the dts of BPI-R4 which
correspond to the two sfp slots. By default they are automatically
named as eth1 and eth2 in bad order, however 'SFP1-WAN' and 'SFP2-LAN'
are printed on the PCB and the official metal case has labels 'SFP-WAN'
and 'SFP-LAN'. Thus, label the ports accordingly to match the
board/case labels.
The COMPAT_VERSION is increased to denote that configuration has to be
adjusted manually.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Sets openwrt,netdev-name for the gmac1 node in the dts of BPI-R3, which
corresponds to the sfp1 slot, to have a proper naming and match the
label on the official BPI-R3 metal case. This renames the port from eth1
to sfp1.
The COMPAT_VERSION is increased to denote that configuration has to be
adjusted manually.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Add support in filogic subtarget for our own custom property
`openwrt,netdev-name` in the device tree instead of `label` for
renaming interfaces. This was suggested upstream to avoid potential
conflicts [1].
[1] https://lore.kernel.org/netdev/20240709124503.pubki5nwjfbedhhy@skbuf/
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
access to undeclared variable radio In [anonymous function](), file /usr/share/hostap/hostapd.uc, line 830, byte 45:
Signed-off-by: Florian Maurer <f.maurer@outlook.de>
Userspace handling is deprecated. MAC address stuff needs to remain
handled in userspace as it's encrypted. Maybe an NVMEM driver can be
written in the future...
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17276
Signed-off-by: Robert Marko <robimarko@gmail.com>
e00958884416 fw4: do not add physical devices for soft offload
dfbcc1cd127c fw4: skip not existing netdev names in flowtable device list
18fc0ead19fa init: use the reload data trigger to reload firewall on procd data changes
Fixes: https://github.com/openwrt/openwrt/issues/13410
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Currently if the host system has cmocka installed it will leak the host
path and try to use the host cmocka and build tests.
This will obviously fail, so backport upstream commit allowing disabling
of tests and disable building them.
Fixes: openwrt/packages#25456
Link: https://github.com/openwrt/openwrt/pull/17297
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add QCA2066 firmware package, ath11k is already supported.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/17260
Signed-off-by: Robert Marko <robimarko@gmail.com>
The qusb_phy node looks for the following supply:
"vdd", "vdda-pll", "vdda-phy-dpdm"
And ssphy node looks for the following supply:
"vdda-phy", "vdda-pll"
So fix the usb regulator supply for RT-AX89X.
Fixes: 1306237 ("qualcommax: use PHY regulator for USB GPIO")
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/17290
Signed-off-by: Robert Marko <robimarko@gmail.com>
93461ca4c827 unet-cli: only apply defaults on create
3e5766783d5d unet-tool: add support for confirming password
074d3659ca4a unet-cli: confirm password when creating new seed based key
bf3488a3807a unet-cli: add add/set-local-host command
9eb57c528461 unet-cli: add support for setting interface zone
a0a2d80f3459 ubus: add firewall rules for network port/pex_port via procd
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2e206dbe77ec service: add support for triggers on service/instance data changes
735b48728fca service: remove leftover lines from previous commit
32469644a029 service: allow incremental changes to service properties
fd01fb852302 service: fix double free bug when dealing with data
Signed-off-by: Felix Fietkau <nbd@nbd.name>
058a099f5bc5 interface: fix memleak and reload issue for the zone attribute
ea01ed41f321 interface: remove unnecessary NULL checks before free()
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Not all Kirkwood systems have the Marvell MV88E6XXX switches.
Drop those from the generic config and add them as modules
in the systems that have it.
This was inferred by inspecting the upstream DTS files for any
mv88e* strings and adding the mv88e6xxx kmod package to those
that have an upstream device tree with an MV88E6xxx switch
and an OpenWrt image target.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
d22d7db581d5 bpf_skb_utils.h: add missing include to fix build against newer kernel headers
bbd3e0eb1419 host: fix peer routes on a node acting as gateway
b17164751fc7 unet-tool: add support for generating keys from salt + seed passphrase
041e05870c20 unet-tool: add support for dumping pubkey from signed file
b58920d420cb unet-tool: add support for extracting network data from signed bin file
f335f5b40b4e unet-cli: add support for generating key from seed
8b1f1d099352 unet-cli: add support for importing networks from signed data
188ba05eadf2 unet-cli: add missing command line help for import
8f15fc306a40 unet-cli: fix add-ssh-host with seed keys
486bc3b86dc2 pex-msg: enable broadcast for global PEX socket
e4a24cdfbc1c unet-cli: fix defaults on create
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This is using mac-base and so a 0 needs to be added.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17274
Signed-off-by: Robert Marko <robimarko@gmail.com>
