Backport upstream fix for incorrect ifdeffery and dependency of CONFIG_KEXEC,
which causes compilation errors with the following symbols:
CONFIG_CRASH_CORE=y
CONFIG_KEXEC_CORE=y
CONFIG_CRASH_DUMP=y
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
This patch adds support for Mikrotik RB5009UG+S+IN.
Specifications:
- SoC: Marvell Armada 7040 (88F7040) - 4 cores, ARMv8 Cortex-A72, 1.4GHz, 64bit
- RAM: 1024MB DDR4
- Flash: 16MB SPI NOR flash, 1024MB NAND
- Ethernet:
* Marvell 88E6393X - Amethyst:
* one 2.5G RJ45 port via Qualcomm QCA8081 PHY
* seven 1G RJ45 ports via built-in PHY-s
* one 10G SFP+ cage
* All ports share the same 10G switch uplink to the CPU
- LED: User, SFP, Hdr1, Hdr2
- Buttons: Reset
- UART: 115200 8n1 on the MikroTik 16 pin header
- USB: One USB3 port
- Power: 24-57 V via
* DC jack
* 802.3af/at PoE on Ethernet 1
* 2-pin terminal on the side
16 Pin header pinout:
1 GND Vcc RX ? GND
#--------------------#
|.-. .-. .-. .-. .-. |
|'-' '-' '-' '-' '-' |
|.-. .-. .-. .-. .-. |
|'-' '-' '-' '-' '-' |
#--------------------#
2 CLK DO /CS TX DI
Do note that the default RouterBoot has disabled UART even when the
required hard-config bit is set to indicate UART support.
Patched RouterBoot must be used if UART is desired.
Also, since ARM64 Linux support does not support in any way appending the
DTB to the kernel image we use mainline U-Boot with added RB5009 support
in order to boot OpenWrt.
MikroTik uses YAFFS to store the boot kernel and we use YAFUT to put U-Boot
as the kernel which RouterBoot then simply boots as an ELF.
Install instructions:
NOTE: In case you are using an existing out of tree version of OpenWrt make
sure to reinstall RouterOS via Netinstall to return the expected partition
layout.
1. Prepare FAT or EXT4 formatted USB drive with OpenWrt initramfs:
* Copy bin/targets/mvebu/cortexa72/openwrt-mvebu-cortexa72-mikrotik_rb5009-initramfs-uImage.itb
to the root of FAT or EXT4 formatted USB drive.
* Plug in the drive to the RB5009 USB port
2. Boot the modified OpenWrt built U-Boot ELF:
u-boot.elf from bin/targets/mvebu/cortexa72/u-boot-rb5009/u-boot.elf
Consult OpenWrt wiki for common instructions on switching to boot from
Ethernet once as well as serving the file:
https://openwrt.org/toh/mikrotik/common
Once U-Boot is booted it will attempt to boot in the following order:
1. NAND
2. USB
3. Network
NAND is expected to fail but USB or Networking need to serve the OpenWrt
initramfs image and after booting it will be accessible from LAN ports
on the default 192.168.1.1 IP with default credentials.
3. Flash modified RouterBoot that enables UART (Optional but recommended):
https://public.robimarko.eu/RB5009/70x0-7.15-uart.fwf
* Copy the file over to the booted OpenWrt initramfs to /tmp
* Run: mtd erase RouterBOOT-primary
* Run: mtd write /tmp/70x0-7.15-uart.fwf RouterBOOT-primary
4. Install U-Boot to boot OpenWrt:
* Copy the u-boot.elf from bin/targets/mvebu/cortexa72/u-boot-rb5009/u-boot.elf
to OpenWrt initramfs to /tmp.
* Run: . /lib/functions.sh
* Run: yafut -d /dev/mtd$(find_mtd_index "YAFFS") -w -i /tmp/u-boot.elf -o kernel -T
This will use yafut to copy the U-Boot as kernel in YAFFS so that RouterBoot boots it.
5. Wipe the NAND UBI partition:
* Run: ubiformat /dev/mtd$(find_mtd_index "ubi") -y
This will prepare the existing RouterOS rootfs partition for OpenWrt.
6. Flash OpenWrt:
* Copy the bin/targets/mvebu/cortexa72/openwrt-mvebu-cortexa72-mikrotik_rb5009-squashfs-sysupgrade.bin
to OpenWrt initramfs to /tmp.
* Run: sysupgrade /tmp/openwrt-mvebu-cortexa72-mikrotik_rb5009-squashfs-sysupgrade.bin
Device will reboot, boot U-Boot and then OpenWrt.
Recovery:
In case you need to reinstall OpenWrt if it crashes after U-Boot, there is
a recovery mechanism in OpenWrt to boot the OpenWrt initramfs.
You need to hold the reset button while U-Boot is booting and then it will
boot the OpenWrt initramfs from:
1. USB
2. Networking
In recovery mode U-Boot will light all of the LED-s except for the switch
ones.
In case you want to return to RouterOS, you can simply do that via
Netinstall like on any other MikroTik board.
Credits also go to Serhii Serhieiev <adron@mstnt.com> who origininally
figured out the RouterBoot modification for UART, the missing 10G MVPP2
support in U-Boot as well as the custom aux loader to boot directly via
RouterBoot.
Link: https://github.com/openwrt/openwrt/pull/15765
Signed-off-by: Robert Marko <robimarko@gmail.com>
MikroTik RB5009 uses RouterBoot as its bootloader like all MikroTik devices
running RouterOS, meaning that its not FIT compatible and can only boot
ELF images.
Now this is not so much of an issue on ARM or MIPS since kernel supports
appending DTB-s to it (Or we patch the kernel to embed it), but on ARM64
there is intentionally no such support.
RouterBoot will pass a DTB, but its the broken MikroTik one which is a
modified reference DTB and incorrect in more places than its valid so we
cannot use it to boot our kernel.
Thus, the solution is to use an intermediary loader and luckily for us
Armada 7040 is well supported in U-Boot which makes it a great option since
it supports anything that we will ever need to boot.
Upstream U-Boot currently requires the Armada boards to be converted to
OF_UPSTREAM before adding anything new and this requires updating all of
the drivers to accomodate the Linux DTS, while I plan to do this eventually
we will need to keep this board downstream for now.
Most stuff is supported in U-Boot, including networking since the switch
is preconfigured by RouterBoot.
A custom environment is used to try and boot from the following devices:
1. NAND (UBI)
2. USB
3. Networking
If NAND boot fails then U-Boot will attempt to boot OpenWrt initramfs from
USB or via networking.
There is a manual recovery mechanism implemented where if the reset button
is held when U-Boot is booting it will try to boot OpenWrt initramfs from:
1. USB
2. Networking
When U-Boot is in recovery mode it will light all of the LED-s except the
switch ones.
Link: https://github.com/openwrt/openwrt/pull/15765
Signed-off-by: Robert Marko <robimarko@gmail.com>
In order to not have to ship envtools configuration per board, we can
instead rely on the kernel U-Boot environment NVMEM driver through which
envtools can read/write the environement.
Since size difference is negligeble and this subtarget has rather large
storage regardless, enable it by default.
Link: https://github.com/openwrt/openwrt/pull/15765
Signed-off-by: Robert Marko <robimarko@gmail.com>
MikroTik RB5009 will be using advantage of the MikroTik platform drivers,
RouterBoot partition parser and SPI NOR variable erase support.
Link: https://github.com/openwrt/openwrt/pull/15765
Signed-off-by: Robert Marko <robimarko@gmail.com>
Marvell 70x0 and 80x0 both have ARM SBSA Generic Watchdog built-in,
so lets enable the required driver for them.
Link: https://github.com/openwrt/openwrt/pull/15765
Signed-off-by: Robert Marko <robimarko@gmail.com>
MikroTik RB5009 uses Qualcomm QCA8081 PHY for the 2.5G RJ45 port,
so we need to enable the driver for it.
Link: https://github.com/openwrt/openwrt/pull/15765
Signed-off-by: Robert Marko <robimarko@gmail.com>
QCA808x does not currently fill in the possible_interfaces.
This leads to Phylink not being aware that it supports 2500Base-X as well
so in cases where it is connected to a DSA switch like MV88E6393 it will
limit that port to phy-mode set in the DTS.
That means that if SGMII is used you are limited to 1G only while if
2500Base-X was set you are limited to 2.5G only.
Populating the possible_interfaces fixes this, so lets backport the patches
from kernel 6.9.
This also includes a backport of the Phylink PHY validation series from
kernel 6.8 that allows the use of possible_interfaces.
Link: https://github.com/openwrt/openwrt/pull/15765
Signed-off-by: Robert Marko <robimarko@gmail.com>
Marvell Amethyst switches use a different SMI GPIO pin setup than other
switches, and since RB5009 uses Amethyst switch and its SMI bus to talk
to QCA8081 lets backport the required fix from kernel 6.9.
Link: https://github.com/openwrt/openwrt/pull/15765
Signed-off-by: Robert Marko <robimarko@gmail.com>
Now that SSDK has been updated to use in-kernel SMEM ID-s to identify
the SoC its running on instead of relying on the downstream socinfo.h
header we can move the read_ipq_soc_version_major() function directly to
cpr3-util.c as its the only user of anything from the header and drop it.
Link: https://github.com/openwrt/openwrt/pull/15786
Signed-off-by: Robert Marko <robimarko@gmail.com>
This hack is used to make sure that the mfd device starts before the
mtd driver[1]. Now the linux driver framework "struct spi_driver {}"
can always ensure this.
[1] 47f8fd1dde ("ar71xx: rewrite SPI drivers for the RB4xx boards")
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
After porting the ar71xx target to the new ath79 target, we are now
using the device tree instead of the device mach file. And the
platform drivers already support deferred probe. So there is no need
to keep it.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Trying to compile for ipq60xx will fail with:
ERROR: modpost: "qca808x_phy_reset" [build_dir/target-aarch64_cortex-a53_musl/linux-qualcommax_ipq60xx/qca-ssdk-2024.06.13~c451136b/qca-ssdk.ko] undefined!
So, lets fix this by disabling Manhattan switch and PHY support as this is
the new 2.5G quad port switch that is not present on ipq60xx boards.
Fixes: 87a45ea432 ("kernel: qca-ssdk: update 12.5 to 2024-06-13")
Signed-off-by: Robert Marko <robimarko@gmail.com>
There are some new commits, so refresh and update patches.
Some build warnings have been fixed upstream too.
Add backport target/linux/generic/backport-6.6/722-v6.10-dt-bindings-arm-qcom-ids-Add-SoC-ID-for-IPQ5321.patch.
Removed upstream:
[-] qca-ssdk/patches/101-hsl_phy-add-support-for-detection-PSGMII-PHY-mode.patch
[-] qca-ssdk/patches/201-fix-compile-warnings.patch
List of changes:
2024-04-16 -c451136b- qca-ssdk: strip MRPPE code
2024-06-05 -f455a820- [qca-ssdk]: fix enum-int-mismatch warnings
2024-05-31 -bbfc0fa9- Merge "[qca-ssdk]: update eee status of phydev"
2024-05-31 -adbe9dc5- Merge "[qca-ssdk]: support psgmii and uqsxgmii mode of kernel"
2024-05-31 -d06ca777- Merge "[qca-ssdk]: fix 5G issue with the AQR FW that use 5gbaser for 5G speed"
2024-05-31 -c6f539a5- Merge "qca-ssdk: support mrppe pktedit padding functions"
2024-04-29 -c321e2a9- qca-ssdk: support mrppe pktedit padding functions
2024-05-24 -ee6e201e- qca-ssdk: Fix the big endian compile error
2024-05-15 -8c116bb9- [qca-ssdk]: update eee status of phydev
2024-05-20 -f0341a2c- Merge "qca-ssdk: Enable igmp for PPE MINI profile"
2024-05-16 -44a0ce93- qca-ssdk: Enable igmp for PPE MINI profile
2024-05-15 -8b91bbf6- [qca-ssdk]: support psgmii and uqsxgmii mode of kernel
2024-05-14 -7eec1658- [qca-ssdk]: fix 5G issue with the AQR FW that use 5gbaser for 5G speed
2024-05-12 -b9f5ea0e- [qca-ssdk]: ethtool support, do not change wake-up timer when the requested timer is 0
2024-05-09 -5e2c15ed- Merge "[qca-ssdk]: remove check when mht clock enable"
2024-05-09 -a1563b90- Merge "[qca-ssdk] support new sku IPQ5321"
2024-04-23 -f04b7680- [qca-ssdk]: show unknown status when link down
2024-03-22 -33b91b30- [qca-ssdk]: remove check when mht clock enable
2024-04-29 -b6362f2b- Merge "qca-ssdk:fix bug in marina nptv6 iid cal"
2024-04-29 -097033ae- Merge "[qca-ssdk] support cypress uniphy0 connecting MHT switch port0"
2024-04-24 -d45560fd- qca-ssdk:fix bug in marina nptv6 iid cal
2024-04-24 -7d7a42af- qca-ssdk: enable policer counter on low memory profile
2024-04-18 -e36cf6ea- Merge "[qca-ssdk]: change portvlan egress mode initial value as untouched"
2024-04-18 -27817881- Merge "[qca-ssdk]: update the aqr phy supported ability"
2024-04-18 -5a3a693c- Merge "qca-ssdk:support marina nptv6"
2024-04-16 -129fe9b3- Merge "qca-ssdk: support tunnel fields and innner fields inverse"
2024-01-09 -fc8f6abd- qca-ssdk:support marina nptv6
Signed-off-by: Kristian Skramstad <kristian+github@83.no>
Link: https://github.com/openwrt/openwrt/pull/15771
Signed-off-by: Robert Marko <robimarko@gmail.com>
This adds two more common PHY brands to the image.
Realtek is used on the Google Coral "Phanbell" board (i.MX8MQ).
SMSC has been used on various Raspberry Pi boards.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Support for 'fsl,imx8mq-usb-phy' is needed for USB to work
on NXP i.MX8MQ and i.MX8MP platforms.
Tested with a Google Coral "Phanbell" board.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
This was discovered when trying to run OpenWrt on Hetzner Cloud's
Arm-based instances.
Hetzner uses QEMU/KVM with virtio-gpu as the main display device,
together with an ACPI firmware. This was not displaying a console
previously.
This setup can be emulated by qemu using options below:
qemu-system-aarch64 \
-machine virt \
-bios QEMU_EFI.fd \
-device virtio-gpu \
-usb \
-device qemu-xhci,id=xhci \
-device usb-tablet,bus=xhci.0 \
-device usb-kbd,bus=xhci.0 \
-vnc :0
Signed-off-by: Mathew McBride <matt@traverse.com.au>
This PMU (performance management unit) related kernel option
can appear under certain kernel configurations (such as
KVM being enabled).
Disable them, as we do with other PMU-related options.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
It has its own dedicated knob
Signed-off-by: Nathaniel Wesley Filardo <nwfilardo@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15761
Signed-off-by: Robert Marko <robimarko@gmail.com>
New dependencies required for the module to be useful, and correct IPv6 support
Signed-off-by: Nathaniel Wesley Filardo <nwfilardo@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15761
Signed-off-by: Robert Marko <robimarko@gmail.com>
Running the glibc-static check with GCC14 as the host compiler will fail:
Please install a static glibc package. (Missing libutil.a, librt.a or libpthread.a)
However, this error will get printed even with the required static
libraries installed when GCC14 is used.
Manually running the check exposes the real error:
<stdin>: In function ‘main’:
<stdin>:1:45: error: implicit declaration of function ‘timer_gettime’ [-Wimplicit-function-declaration]
GCC14 now errors on implicit declarations by default, so lets add the
required time.h header to fix compilation and thus the check.
Link: https://github.com/openwrt/openwrt/pull/15778
Signed-off-by: Robert Marko <robimarko@gmail.com>
Fakeroot uses an egrep configure check to look for the string "time64"
within a preprocessed include of the sys/stat.h header
in order to decide whether or not to create declarations
and internal functions used for wrapping the native functions
stat64_time64 fstat64_time64 lstat64_time64 and fstatat64_time64.
On specific older versions of glibc these functions are not included,
but there are some references to "time64" unrelated to functions,
like aliasing the time64_t typedef to the standard time_t typedef
when the size of a word is 64 bits or defining it if not.
In this case, a grep for "stat64"
of the preprocessed sys/stat.h header matches nothing,
however, the grep for "time64" in the configure check
of the preprocessed sys/stat.h header matches a line
that has nothing to do with the functions
that will be wrapped as a result of successful matching.
__extension__ typedef __int64_t __time64_t;
This causes the attempt to wrap the functions to occur,
which fails due to some of the corresponding macros being empty
since the native declarations they are based on do not exist,
causing a common error claiming that a part of the syntax is missing.
error: expected '=', ',', ';', 'asm' or '__attribute__' before ...
Fix this by making the testing regular expression more complex
in order to match actual function names ending in "_time64"
with or without a set of preceding underscores, but none after.
Signed-off-by: Michael Pratt <mcpratt@pm.me>
Link: https://github.com/openwrt/openwrt/pull/15773
Signed-off-by: Robert Marko <robimarko@gmail.com>
Currently, the build option to enable/disable engine support isn't
reflected in the final '/etc/ssl/openssl.cnf' config. It assumes `engines`
is always enabled, producing an error whenever running any
commands in openssl util or programs that explicitly use settings
from '/etc/ssl/openssl.cnf'.
```
➤ openssl version
FATAL: Startup failure (dev note: apps_startup()) for openssl
307D1EA97F000000:error:12800067:lib(37):dlfcn_load:reason(103):crypto/dso/dso_dlfcn.c:118:filename(libengines.so):
Error loading shared library libengines.so: No such file or directory
307D1EA97F000000:error:12800067:lib(37):DSO_load:reason(103):crypto/dso/dso_lib.c:152:
307D1EA97F000000:error:0700006E:lib(14):module_load_dso:reason(110):crypto/conf/conf_mod.c:321:module=engines, path=engines
307D1EA97F000000:error:07000071:lib(14):module_run:reason(113):crypto/conf/conf_mod.c:266:module=engines
```
Build should check for the `CONFIG_OPENSSL_ENGINE` option, and comment out `engines`
if not explicitly enabled.
Example:
```
[openssl_init]
providers = provider_sect
```
After this change, openssl util works correctly.
```
➤ openssl version
OpenSSL 3.0.14 4 Jun 2024 (Library: OpenSSL 3.0.14 4 Jun 2024)
```
Signed-off-by: Sean Khan <datapronix@protonmail.com>
Link: https://github.com/openwrt/openwrt/pull/15661
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add a set of upstream patches for the imx8m{m,n,p} based Venice
boards.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Link: https://github.com/openwrt/openwrt/pull/15736
Signed-off-by: Robert Marko <robimarko@gmail.com>
The GW74xx's first RJ45 is eth0 which should be the WAN adapter, not
eth1 which is the CPU uplink port to the switch.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Link: https://github.com/openwrt/openwrt/pull/15736
Signed-off-by: Robert Marko <robimarko@gmail.com>
qoriq has had kernel 6.1 as testing for 2 months now, so lets default to
it and drop 5.15 support.
Link: https://github.com/openwrt/openwrt/pull/15767
Signed-off-by: Robert Marko <robimarko@gmail.com>
224d497dd94f srec2bin: drop unused "dum" variable
6777b2d51961 uimage_sgehdr: use "char" type for header struct strings
81db3025aac5 uimage_sgehdr: drop unused "ltmp" variable
bd7fcc74b43e pc1crypt: make decrypt/encrypt functions take void * as argument
6ac44974185a linksys: add magic header generation tool for e8350 v1
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
224d497dd94f srec2bin: drop unused "dum" variable
6777b2d51961 uimage_sgehdr: use "char" type for header struct strings
81db3025aac5 uimage_sgehdr: drop unused "ltmp" variable
bd7fcc74b43e pc1crypt: make decrypt/encrypt functions take void * as argument
6ac44974185a linksys: add magic header generation tool for e8350 v1
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Currently, information from MikroTik hard_config is only available via
sysfs, meaning that we have to rely on userspace to for example setup MACs.
So, lets provide a basic NVMEM layout based driver to expose the same cells
as sysfs driver exposes.
Do note that the we dont extract the WLAN caldata and BDF-s at this point.
Reviewed-by: Thibaut VARÈNE <hacks@slashdirt.org>
Link: https://github.com/openwrt/openwrt/pull/15665
Signed-off-by: Robert Marko <robimarko@gmail.com>
Move the hard config tag ID-s to a separate header so they can be reused
by the NVMEM driver as well.
Link: https://github.com/openwrt/openwrt/pull/15665
Signed-off-by: Robert Marko <robimarko@gmail.com>
This driver has already been packed as a software package. There is
no need to build it into the kernel.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
