Commit Graph

89 Commits

Author SHA1 Message Date
Chuanhong Guo
a9360452f0 ath79: add support for Qihoo C301
Specifications:
- SoC: AR9344
- RAM: 128MB
- Flash: 2 * 16MB (MX25L12845)
- Ethernet: 2 * FE LAN & 1 * FE WAN
- WiFi: 2.4G: AR9344 5G: QCA9882

Flash instruction:
1. Hold reset and power up the router
2. Set your IP to 192.168.1.x
3. Open 192.168.1.1 and upload the generated *factory* firmware

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2019-07-16 09:51:03 +08:00
David Bauer
cb3cd52694 ath79: add support for devolo WiFi pro 1750x
Hardware
--------
CPU:   Qualcomm Atheros QCA9558
RAM:   128M DDR2
FLASH: 16MiB
ETH:   1x Atheros AR8035 (PoE in)
WiFi2: QCA9558 3T3R
WiFi5: QCA9880 3T3R
BTN:   1x Reset
LED:   1x LED Power (non-controllable)
       1x LED Status (internal)
       1x LED LAN (controlled by PHY)
       1x LED WLAN
BEEP:  1x GPIO attached piezo beeper
UART:  3.3V GND TX RX (115200-N-8) (3.3V is square pad)
       Header is located next to external-LED header.

Installation
------------
Make sure you set a password for the root user as prompted on first
setup!

1. Upload OpenWRT sysupgrade image via SSH to the device.
Use /tmp as the destination folder on the device.
User is root, password the one set in the web interface.

2. Install OpenWRT with

> sysupgrade -n -F /tmp/<openwrt-image-name>

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-07-14 16:20:53 +02:00
Adrian Schmutzler
1174b94bc9 ath79: Fix whitespace errors in 11-ath10k-caldata
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-07-09 23:05:51 +02:00
Adrian Schmutzler
ab02584685 ath79: Use -v1 suffix for TP-Link WDR3600/4300
In ath79, identifiers tplink_tl-wdr3600 and tplink_tl-wdr4300 have
been used while most other TP-Link devices include the revision.

Although there actually is only one major revision of these
devices, they bear the revision on their bottom (v1.x). TP-Link
also refers to the devices as V1 on its web page.

This patch thus adds -v1 to both so it is more consistent
with other devices and with what you would expect from reading
the on-device sticker and the support pages.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-07-03 07:45:00 +02:00
Adrian Schmutzler
28baaaae82 ath79: Merge cases in 11-ath10k-caldata
Cosmetical patch that just merges two cases.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-06-15 19:55:32 +02:00
Adrian Schmutzler
fde0abf267 ath79: Add support for TP-Link Archer C25 v1
The TP-Link Archer C25 is a low-cost dual-band router.

Specification:

- CPU: Atheros QCA9561 775 MHz
- RAM: 64 MB
- Flash: 8 MB
- Wifi: 3x3 2.4 GHz (integrated), 1x1 5 GHz QCA9887
- NET: 5x 10/100 Mbps Ethernet

Some LEDs are controlled by an additional 74HC595 chip, but not
all of them as e.g. for the C59.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-06-10 11:25:47 +02:00
Adrian Schmutzler
fcb920ffe7 ath79: Consistently label art partition with lower case
This patch harmonizes the label and alias for art partitions
across ath79. Since lower case seems to be more frequent, use that
consistently.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-06-10 11:25:41 +02:00
Adrian Schmutzler
4d807ad2d9 ath79: Read MAC addresses from flash in 11-ath10k-caldata
In commit c3a8518 eth0 and eth1 have been swapped for some devices,
but 11-ath10k-caldata has not been updated.
Instead of fixing this by swapping eth0/eth1, this patch will read
addresses from flash (as done for several devices already) so
adjustments due to eth order become obsolete.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-06-10 11:25:41 +02:00
Ryan Mounce
6d6985ff0e ath79: add support for WD My Net N750
SoC: AR9344
RAM: 128MB
Flash: 16MiB Winbond 25Q128BVFG SPI NOR
5GHz WiFi: AR9380 PCIe 3x3:3 802.11n
2.4GHz WiFi: AR9344 (SoC) AHB 2x2:2 802.11n

5x Gigabit ethernet via AR8327N switch (green + amber LEDs)
2x USB 2.0 via GL850G hub
4x front LEDs from SoC GPIO
1x front WPS button from SoC GPIO
1x bottom reset button from SoC GPIO

Known issues:
AR8327N LEDs only have default functionality, not presented in sysfs.
This is a regression from ar71xx.

UART header JP1, 115200 no parity 1 stop
TX
GND
VCC
(N/P)
RX

See https://openwrt.org/toh/wd/n750 for flashing detail.
Procedures unchanged from ar71xx.

Tested sysupgrade + factory flash from WD Emergency Recovery

Signed-off-by: Ryan Mounce <ryan@mounce.com.au>
2019-05-27 22:44:08 +02:00
Davide Fioravanti
f5d2c91415 ath79: add support for TP-Link Archer D50 V1
TP-Link Archer D50 v1 is a dual-band AC1200 router + modem.
The router section is based on Qualcomm/Atheros QCA9531 + QCA9882.
The "DSL" section is based on BCM6318 but it's currently not supported.

Internally eth0 is connected to the Broadcom CPU.

Router section - Specification:

CPU: QCA9531 650/600/200 MHz (CPU/DDR/AHB)
RAM: 64 MB (DDR2)
Flash: 8 MB (SPI NOR)
Wifi 2.4GHz: QCA9531 2T2R
Wifi 5GHz: QCA9982 2T2R
4x 10/100 Mbps Ethernet
8x LED, 3x button
UART header on PCB

Known issues:
DSL not working (eth0) (WIP)

UART connection
---------------
J2 HEADER (Qualcomm CPU)
. TX
. RX
. GND
O VCC

J16 HEADER (Broadcom CPU)
O VCC
. GND
. RX
. TX

The following instructions require a connection to the J2 UART header.

Flash instruction under U-Boot, using UART
------------------------------------------
 1. Press any key to stop autobooting and obtain U-Boot CLI access.
 2. Setup ip addresses for U-Boot and your tftp server.
 3. Issue below commands:
	tftpboot 0x81000000 openwrt-ath79-generic-tplink_archer-d50-v1-squashfs-sysupgrade.bin
	erase 0x9f020000 +$filesize
	cp.b 0x81000000 0x9f020000 $filesize
	reset

Initramfs instruction under U-Boot for testing, using UART
----------------------------------------------------------
 1. Press any key to stop autobooting and obtain U-Boot CLI access.
 2. Setup ip addresses for U-Boot and your tftp server.
 3. Issue below commands:
	tftpboot 0x81000000 openwrt-ath79-generic-tplink_archer-d50-v1-initramfs-kernel.bin
	bootm 0x81000000

Restore the original firmware
-----------------------------
 0. Backup every partition using the OpenWrt web interface
 1. Download the OEM firmware from the TP-Link website
 2. Extract the bin file in a folder (eg. Archer_D50v1_0.8.0_1.3_up_boot(170223)_full_2017-02-24_09.37.45.bin)
 3. Remove the U-Boot and the Broadcom image part from the file.
    Issue the following command:
	dd if="Archer_D50v1_0.8.0_1.3_up_boot(170223)_full_2017-02-24_09.37.45.bin" of="Archer_D50v1_0.8.0_1.3_up_boot(170223)_full_2017-02-24_09.37.45.bin.mod" skip=257 bs=512 count=15616
 4. Double check the .mod file size. It must be 7995392 bytes.
 5. Flash it using the OpenWrt web interface. Force the update if needed.
    WARNING: Remember to NOT keep settings.

 5b. (Alternative to 5.) Flash it using the U-Boot and UART connection.
     Issue below commands in the U-Boot:
        tftpboot 0x81000000 Archer_D50v1_0.8.0_1.3_up_boot(170223)_full_2017-02-24_09.37.45.bin.mod
        erase 0x9f020000 +$filesize
        cp.b 0x81000000 0x9f020000 $filesize
        reset

Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [removed
default-state = "off", it's already the default, added pcie node,
fixed typo]
2019-05-18 17:59:49 +02:00
sven friedmann
30dcbc741d ath79: add support for EnGenius ECB1750
Specification:

- Qualcomm Atheros SoC QCA9558
- 720/600/200 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 1x 10/100/1000 Mbps Ethernet
- 3T3R 2.4 GHz (QCA9558 WMAC)
- 3T3R 5.8 Ghz (QCA9880-BR4A, Senao PCE4553AH)

https://fccid.io/A8J-ECB1750

Tested and working:

- lan, wireless, leds, sysupgrade (tftp)

Flash instructions:

1.) tftp recovery

- use a 1GbE switch or direct attached 1GbE link
- setup client ip address 192.168.1.10 and start tftpd
- save "openwrt-ath79-generic-engenius_ecb1750-initramfs-kernel.bin" as "ap.bin" in tfpd root directory
- plugin powercord and hold reset button 10secs.. "ap.bin" will be downloaded and executed
- afterwards login via ssh and do a sysuprade

2.) oem webinterface factory install (not tested)

Use normal webinterface upgrade page und select "openwrt-ath79-generic-engenius_ecb1750-squashfs-factory.bin".

3.) oem webinterface command injection

OEM Firmware already running OpenWrt (Attitude Adjustment 12.09).
Use OEM webinterface and command injection. See wiki for details.

https://openwrt.org/toh/engenius/engenius_ecb1750_1

Signed-off-by: sven friedmann <sf.openwrt@okay.ms>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[use interrupt-driven "gpio-keys" binding]
2019-05-18 13:43:55 +02:00
Daniel Gimpelevich
f61e754522 ath79: add support for Netgear EX6400 and EX7300
This is sold as a dual-band 802.11ac range extender. It has a sliding
switch for Extender mode or Access Point mode, a WPS button, a recessed
Reset button, a hard-power button, and a multitude of LED's, some
multiplexed via an NXP 74AHC164D chip. The internal serial header pinout is
Vcc, Tx, Rx, GND, with GND closest to the corner of the board. You may
connect at 115200 bps, 8 data bits, no parity, 1 stop bit.

Specification:
- System-On-Chip: QCA9558
- CPU/Speed: 720 MHz
- Flash-Chip: Winbond 25Q128FVSG
- Flash size: 16 MiB
- RAM: 128 MiB
- Wireless No1: QCA9558 on-chip 2.4GHz 802.11bgn, 3x3
- Wireless No2: QCA99x0 chip 5GHz 802.11an+ac, 4x4
- PHY: Atheros AR8035-A

Installation:
If you can get to the stock firmware's firmware upgrade option, just feed
it the factory.img and boot as usual. As an alternative, TFTP the
factory.img to the bootloader.

Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
[whitespace fix in DTS and reorder of make variables]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-04-09 11:09:26 +02:00
Markus Scheck
de2f888024 ath79: add support for OCEDO Ursus
SOC:   Qualcomm Atheros QCA9558
RAM:   128MB
FLASH: 16MB (Macronix MX25L12845EMI-10G)
WLAN1: QCA9558 2.4GHz 802.11bgn 3SS
WLAN2: QCA9880 5GHz 802.11ac 3SS
LED:   Power, LAN1, LAN2, 2.4GHz, 5GHz
Serial:Next to SPI Flash,
       Pinout is 3V3 - GND - TX - RX (Square Pin is 3V3)
       The Serial setting is 115200-8-N-1

INSTALLATION:

1. Serve an OpenWrt ramdisk image named "ursus.bin".
   Set your IP-address to 192.168.100.8/24.
2. Connect to the serial. Power up the device and interrupt
   the boot process.
3. Set the correct bootcmd with
   > setenv bootcmd run bootcmd_1
   > saveenv
4. Run
   > tftpboot 0x81000000 ursus.bin
   > bootm 0x81000000
5. Wait for OpenWrt to boot up.
6. Transfer OpenWrt sysupdate image and flash via sysupgrade.

Signed-off-by: Markus Scheck <markus.scheck1@gmail.com>
Tested-by: David Bauer <mail@david-bauer.net>
[whitespace fix, renamed LED labels and SoC type fix]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-04-08 18:37:04 +02:00
INAGAKI Hiroshi
643fcfc8d6 ath79: add support for NEC Aterm WG1200CR
NEC Aterm WG1200CR is a 2.4/5 GHz band 11ac router,
based on Qualcomm Atheros QCA9563.

Specification:

- SoC		: Qualcomm Atheros QCA9563
- RAM		: DDR2 128 MiB
- Flash		: SPI-NOR 8 MiB
- WLAN		: 2.4/5 GHz 2T2R
  - 2.4 GHz	: QCA9563 (SoC)
  - 5 GHz	: QCA9888
- Ethernet	: 2x 10/100/1000 Mbps
  - Switch	: QCA8334
- LEDs/Input	: 12x/4x (2x buttons, 1x slide-switch)
- UART		: through-hole on PCB
  - JP1: Vcc, GND, NC, TX, RX from power connector side
  - 115200 bps

Flash instruction using factory image:

1. Boot WG1200CR normaly
2. Access to "http://192.168.10.1/" and open firmware update page
("ファームウェア更新")
3. Select the OpenWrt factory image and click update ("更新") button
to perform firmware update
4. Wait ~150 seconds to complete flashing

Known issues:

- cannot be controlled LEDs other than Power (Green/Red)
  - only Power LEDs are connected to SoC GPIO; other LEDs
    connected to the gpiochip on ath10k chip (QCA9888)

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [commit
message formatting]
2019-04-06 19:14:06 +02:00
Tobias Schramm
d78e229903 ath79: Add support for Ubiquiti NanoBeam AC
The NanoBeam is a small AR9342 based directional 5 GHz AC CPE with hardware
almost identical to the Ubiquiti NanoStation AC loco. Over the NanoStation
AC loco it has 5 additional LEDs. Four of those LEDs are used as rssi
indicators, the fifth LED is used as an ethernet link/activity indicator.

CPU:   Atheros AR9342 SoC
RAM:   64 MB DDR2
Flash: 16 MB NOR SPI
WLAN:  QCA988X
Ports: 1x GbE

Flashing procedure is identical to the NanoStation AC loco and can be performed
either via serial or the factory firmware upgrade.

Serial flashing:

1. Connect to serial header on device (8N1 115200)
2. Power on device and enter uboot console
3. Set up tftp server serving an openwrt initramfs build
4. Load initramfs build using the command tftpboot in the uboot cli
5. Boot the loaded image using the command bootm
6. Copy squashfs openwrt sysupgrade build to the booted device
7. Use mtd to write sysupgrade to partition "firmware"
8. Reboot and enjoy

Flashing through factory firmware:

1. Ensure firmware version v8.5.0.36727 is installed. Up/downgrade to this exact version.
2. Patch fwupdate.real binary using `hexdump -Cv /bin/ubntbox | sed 's/14 40 fe fe/00 00 00 00/g' | hexdump -R > /tmp/fwupdate.real`
3. Make the patched fwupdate.real binary executable using `chmod +x /tmp/fwupdate.real`
4. Copy the squashfs factory image to /tmp on the device
5. Flash OpenWRT using `/tmp/fwupdate.real -m <squashfs-factory image>`
6. Wait for the device to reboot

Thanks to @cybermaus for testing!

Tested-by: Maurits van Dueren den Hollander <cybermaus@gmail.com>
Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
2019-03-22 00:40:29 +01:00
Adrian Schmutzler
e1ba59ea5c ath79: Speed up caldata/eeprom handling
Reading and writing to and from flash storage is slowed down
enormously by some functions which use a block size of 1.

This patch reworks the extraction scripts to be much faster and
efficient by reading and writing in possibly one big block.

This is based on the initial commit a69e101 for ipq40xx by
Christian Lamparter <chunkeey@gmail.com>.

Speed comparison @ UBNT AC-Mesh (just manually) results
in a time reduction by three orders of magnitude (99.9 %).

> time dd if=/dev/mtd6 of=/lib/firmware/test-slow bs=1 count=4096 skip=4096
4096+0 records in
4096+0 records out
real    0m 16.84s
user    0m 0.07s
sys     0m 13.54s

> time dd if=/dev/mtd6 of=/lib/firmware/test-fast bs=4096 count=1 skip=4096 iflag=skip_bytes
1+0 records in
1+0 records out
real    0m 0.02s
user    0m 0.00s
sys     0m 0.02s

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Rosen Penev <rosenp@gmail.com>
2019-03-13 16:27:41 +01:00
Tomasz Maciej Nowak
ee34740ca3 ath79: add suport for EnGenius EPG5000
EnGenius EPG5000 (v1.0.0, marketed as IoT Gateway) is a dual band
wireless router.

Specification
SoC:		Qualcomm Atheros QCA9558
RAM:		256 MB DDR2
Flash:		16 MB SPI NOR
WIFI:		2.4 GHz 3T3R integrated
		5 GHz 3T3R QCA9880 Mini PCIe card
Ethernet:	5x 10/100/1000 Mbps QCA8337N
USB:		1x 2.0
LEDS:		4x GPIO controlled
Buttons:	2x GPIO controlled
UART:		4 pin header, starting count from white triangle on PCB
		1. VCC 3.3V, 2. GND, 3. TX, 4. RX
		baud: 115200, parity: none, flow control: none

Installation
1. Connect to one of LAN (yellow) ethernet ports,
2. Open router configuration interface,
3. Go to Tools > Firmware,
4. Select OpenWrt factory image with dlf extension and hit Apply,
5. Wait few minutes, after the Power LED will stop blinking, the router
   is ready for configuration.

Alternative installation
1. Prepare TFTP server with OpenWrt sysupgrade image,
2. Connect to one of LAN (yellow) ethernet ports,
3. Connect to UART port (leaving out VCC pin!),
4. Power on router,
5. When asked to enter a number 1 or 3 hit 2, this will select flashing
   image from TFTP server option,
6. You'll be prompted to enter TFTP server ip (default is 192.168.99.8),
   then router ip (default is 192.168.99.9) and for last, image name
   downloaded from TFTP server (default is uImageESR1200_1750),
7. After providing all information U-Boot will start flashing the image,
   You can observe progress on console, it'll take few minutes and when
   the Power LED will stop blinking, router is ready for configuration.

Additional information
If connected to UART, when prompted for number on boot, one can enter
number 4 to open bootloader (U-Boot) command line.
OEM firmware shell password is: aigo3d0a0tdagr
useful for creating backup of original firmware.
When doing upgrade from OpenWrt ar71xx image, it is recomended to not keep
the old configuration.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2019-03-13 16:25:35 +01:00
Piotr Dymacz
db91418766 ath79: add support for TP-Link RE350K v1
TP-Link RE350K v1 (FCC ID: TE7RE350K) is a wall-plug AC1200 Wi-Fi range
extender with 'Kasa Smart' support. Device is based on Qualcomm/Atheros
QCA9558 + QCA9882 + AR8035 platform and is available only on US market.

Specification:

- 720/600/200 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of flash (SPI NOR)
- 1x 1 Gbps Ethernet (AR8035)
- 2T2R 2.4 GHz (QCA9558), with ext. PA (SE2565T) and LNA (SKY65971-11)
- 2T2R 5 GHz (QCA9882), with ext. PA (SE5003L1-R) and LNA (SKY65981-11)
- 2x U.FL connector on PCB
- 2x dual-band PCB antennas
- 1x LED, 2x dual-color LED (all driven by GPIO)
- 3x button (app config, led, reset)
- 1x mechanical on/off slide switch
- 1x UART (4-pin, 2.54 mm pitch) header on PCB
- 1x JTAG (8-pin, 1.27 mm pitch) header on PCB

Flash instruction:
Use 'factory' image directly in vendor GUI (default IP: 192.168.0.254,
default credentials: admin/admin).

Warning:
This device does not include any kind of recovery mechanism in U-Boot.

Vendor firmware access:
You can access vendor firmware over serial (RX line requires jumper
resistor in R306 place, near XTAL) with: root/sohoadmin credentials.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2019-03-11 22:00:26 +01:00
Piotr Dymacz
6fa94d5e8f ath79: add support for YunCore A770
YunCore A770 is a ceiling AC750 AP with 2 Fast Ethernet ports, PoE
(802.3at) support, based on QCA9531 + QCA9887.

Specification:

- 650/597/216 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of flash (SPI NOR)
- 2x 10/100 Mbps Ethernet (PoE 802.3at support in WAN port)
- 2T2R 2.4 GHz (QCA9531), with ext. PA and LNA
- 1T1R 5 GHz (QCA9887), with ext. FEM (SKY85728-11)
- 2x regular LED, 1x RGB LED (all driven by GPIO)
- 1x button (reset)
- DC jack for main power input (12 V)
- UART header on PCB

Flash instruction:

1. First, gain root access to the device, following below steps:

- Login into web gui (default password/IP: admin/192.168.188.253).
- Go to 'Advanced' -> 'Management' -> 'System' and download backup of
  configuration (bakfile.bin).
- Open the file as tar.gz archive, edit/update 'shadow' file and change
  hash of root password to something known.
- Repack the archive, rename it back to 'bakfile.bin' and use to
  restore configuration of the device.
- After that, device will reboot and can be accessed over SSH.

2. Then, install OpenWrt:

- Login over SSH and issue command:
  fw_setenv bootcmd "bootm 0x9f050000 || bootm 0x9fe80000"
- Upload 'sysupgrade' image and install it (only if previous command
  succeeded) with command: 'sysupgrade -n -F openwrt-...'.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2019-03-09 16:31:17 +01:00
Dmitry Tunin
21e90685b6 ath79: speed up ath9k-eeprom extraction
This is a simple copy of ipq40xx: speed up ath10k-caldata
extraction commit a69e101ed1

Tested on DIR-825-B1

3768+0 records in
3768+0 records out
real	0m 11.90s
user	0m 0.03s
sys	0m 9.94s

1+0 records in
1+0 records out
real	0m 0.03s
user	0m 0.00s
sys	0m 0.03s

With this change eeprom extraction is fast enough to get
working Wi-Fi after initial install.

Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com>
2019-03-02 12:59:48 +01:00
Bart Lauret
4386054549 ath79: add support for TP-Link Archer C5 v1
TP-Link Archer C5 v1 is a dual band router
based on Qualcomm/Atheros QCA9558 + QCA9880.

Specification:

 - 720 MHz CPU
 - 128 MB of RAM (Various chips)
 - 16 MB of FLASH (Various chips)
 - SoC QCA9558 integrated 3T3R 2.4 GHz Wi-Fi
 - minipcie slot with 3T3R 5 GHz QCA9880-BR4A
 - 5x 10/100/1000 Mbps Ethernet (AR8327N Switch)
 - 10x LEDs, 2x software buttons

For further informwation on the device, visit the wiki:
<https://openwrt.org/toh/tp-link/archer-c5-c7-wdr7500>

Signed-off-by: Bart Lauret <bblauret@gmail.com>
2019-02-28 11:32:55 +01:00
INAGAKI Hiroshi
93d4439454 ath79: add support for I-O DATA WN-AC1600DGR
I-O DATA WN-AC1600DGR is a 2.4/5 GHz band 11ac router, based on
Qualcomm Atheros QCA9557.

Specification:

- SoC:      Qualcomm Atheros QCA9557
- RAM:      128 MB
- Flash:    16 MB
- WLAN:     2.4/5 GHz
  - 2.4 GHz: 2T2R (SoC internal)
  - 5 GHz:   3T3R (QCA9880)
- Ethernet: 5x 10/100/1000 Mbps
  - Switch: QCA8337N
- LED/key:  6x/6x(4x buttons, 1x slide switch)
- UART:     through-hole on PCB
  - Vcc, GND, TX, RX from ethernet port side
  - 115200n8

Flash instruction using factory image:

1. Connect the computer to the LAN port of WN-AC1600DGR
2. Connect power cable to WN-AC1600DGR and turn on it
3. Access to "http://192.168.0.1/" and open firmware update page
("ファームウェア")
4. Select the OpenWrt factory image and click update ("更新") button
5. Wait ~150 seconds to complete flashing

Alternative flash instruction using initramfs image:

1. Prepare a computer and TFTP server software with the IP address
"192.168.99.8" and renamed OpenWrt initramfs image
"uImageWN-AC1600DGR"
2. Connect between WN-AC1600DGR and the computer with UART
3. Connect power cable to WN-AC1600DGR, press "4" on the serial
console and enter the U-Boot console
4. execute "tftpboot" command on the console and download initramfs
image from the TFTP server
5. execute "bootm" command and boot OpenWrt
6. On initramfs image, download the sysupgrade image to the device
and perform sysupgrade with it
7. Wait ~150 seconds to complete flashing

This commit also removes unnecessary "qca,no-eeprom" property from
the ath10k wifi node.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2019-02-14 16:56:15 +01:00
Oldřich Jedlička
12310f05b7 ath79: add support for TP-LINK Archer C7 v4
TP-Link Archer C7 v4 is a dual-band AC1750 router, based on the
Qualcomm/Atheros QCA9561 SoC + QCA9880.

Specification:

- 775/650/258 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 3T3R 5 GHz
- 5x 10/100/1000 Mbps Ethernet
- 7x LED, 2x button
- UART header on PCB

Flash instruction:
1. Upload openwrt-ath79-generic-tplink_archer-c7-v4-squashfs-factory.bin
   via Web interface

Flash instruction using TFTP recovery:
1. Set PC to fixed ip address 192.168.0.66
2. Download openwrt-ath79-generic-tplink_archer-c7-v4-squashfs-factory.bin
   and rename it to ArcherC7v4_tp_recovery.bin
3. Start a tftp server with the file tp_recovery.bin in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
   the firmware should be transferred from the tftp server
8. Wait ~30 second to complete recovery.

Signed-off-by: Oldřich Jedlička <oldium.pro@gmail.com>
2019-02-05 19:37:31 +01:00
Skirmantas Lauzikas
9c01273e5e ath79: add support for TP-Link Archer C2 V3 (AC900)
This commit adds support for the TP-link Archer C2 V3 (AC900).

Specifications:

 - CPU: QCA9563 750Mhz
 - Ram: 64MB (DDR2)
 - Flash: 8MB (SPI NOR)
 - Ethernet: 5x 10/100/1000
 - Wifi: QCA9563 bgn + QCA9887 an+ac
 - 9x Leds, 2x buttons

Flash instructions:

Upload openwrt-ath79-generic-tplink_archer-c2-v3-squashfs-factory.bin
via the router Web interface and flash as normal firmware update.

Signed-off-by: Skirmantas Lauzikas <skirmantas.lauzikas@blackraven.lt>
[reorder entries, fix trailing whitespace in dts, add firmware partition
 compatible string, remove led default off states, use default on state
 for system led, reuse tplink-safeloader-uimage image build recipe, squash
 with dynamic partitioning commit, reword commit message, add
 installation instructions]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2019-01-27 16:41:10 +01:00
Django Armstrong
1c2f7b5115 ath79: add support for Devolo WiFi Pro 1750e
Hardware
--------
CPU:   Qualcomm Atheros QCA9558
RAM:   128M DDR2
FLASH: 16MiB
ETH:   1x Atheros AR8035 (PoE in)
       1x Atheros AR8033
WiFi2: QCA9558 3T3R (SiGE SE2565T 2.4 GHz power amp x3)
WiFi5: QCA9880 3T3R (Skyworks 5003L1 5 GHz power amp x3)
BTN:   1x Reset
       1x WPS
       1x USB eject
LED:   1x LED blue
       1x LED red
BEEP:  1x GPIO attached piezo beeper
UART:  3.3V GND TX RX (115200-N-8) (3.3V is pin closest to rear ports)
       Dupont 4 pin header
       Rear RJ45 serial port non-functional
USB:   1x v2.0

Installation
------------
Make sure you set a password for the root user as prompted on first
setup!

1. Upload OpenWRT sysupgrade image via SSH to the device.
Use /tmp as the destination folder on the device.
User is root, password previously set in the web interface.

2. Install OpenWRT with

> sysupgrade -n -F /tmp/<openwrt-image-name>

Signed-off-by: Django Armstrong <iamdjango@hotmail.com>
2019-01-26 21:46:33 +01:00
David Bauer
c8115167f9 ath79: add support for devolo WiFi pro 1200i
Hardware
--------
CPU:   Qualcomm Atheros QCA9558
RAM:   128M DDR2
FLASH: 16MiB
ETH:   1x Atheros AR8035 (PoE in)
WiFi2: QCA9558 2T2R
WiFi5: QCA9880 2T2R
BTN:   1x Reset
LED:   1x LED blue
       1x LED red
BEEP:  1x GPIO attached piezo beeper
UART:  3.3V GND TX RX (115200-N-8) (3.3V is square pad)
       Header is located next to reset-button

Installation
------------
Make sure you set a password for the root user as prompted on first
setup!

1. Upload OpenWRT sysupgrade image via SSH to the device.
Use /tmp as the destination folder on the device.
User is root, password the one set in the web interface.

2. Install OpenWRT with

> sysupgrade -n -F /tmp/<openwrt-image-name>

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-01-05 21:55:22 +01:00
David Bauer
8d68be8057 ath79: add support for devolo WiFi pro 1750i
Hardware
--------
CPU:   Qualcomm Atheros QCA9558
RAM:   128M DDR2
FLASH: 16MiB
ETH:   1x Atheros AR8035 (PoE in)
WiFi2: QCA9558 3T3R
WiFi5: QCA9880 3T3R
BTN:   1x Reset
LED:   1x LED blue
       1x LED red
BEEP:  1x GPIO attached piezo beeper
UART:  3.3V GND TX RX (115200-N-8) (3.3V is square pad)
       Header is located next to reset-button

Installation
------------
Make sure you set a password for the root user as prompted on first
setup!

1. Upload OpenWRT sysupgrade image via SSH to the device.
Use /tmp as the destination folder on the device.
User is root, password the one set in the web interface.

2. Install OpenWRT with

> sysupgrade -n -F /tmp/<openwrt-image-name>

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-01-05 21:55:22 +01:00
Christoph Krapp
59b99e1924 ath79: align GL-AR750S boardname to other GL.iNet devices
As the official device name is GL-AR750S, rename the board accordingly.

Signed-off-by: Christoph Krapp <achterin@googlemail.com>
2019-01-01 19:42:41 +01:00
Georgi Vlaev
d03aae1a09 ath79: add support for TP-Link Archer C6 v2
This patch adds support for TP-Link Archer C6 v2 (EU)

Hardware specification:
- SOC: Qualcomm QCA9563 @ 775MHz
- Flash: GigaDevice GD25Q64CSIG (8MiB)
- RAM: Zentel A3R1GE40JBF (128 MiB DDR2)
- Ethernet: Qualcomm QCA8337N: 4x 1Gbps LAN + 1x 1Gbps WAN
- Wireless:
  - 2.4GHz (bgn) QCA9563 integrated (3x3)
  - 5GHz (ac) Qualcomm QCA9886 (2x2)
- Button: 1x power, 1x reset, 1x wps
- LED: 6x LEDs: power, wlan2g, wlan5g, lan, wan, wps
- UART: There's no UART header on the board

Flash instructions:

Upload
openwrt-ath79-generic-tplink_archer-c6-v2-squashfs-factory.bin
via the router Web interface.

Flash instruction using tftp recovery:

1. Connect the computer to one of the LAN ports of the router
2. Set the computer IP to 192.168.0.66
3. Start a tftp server with the OpenWrt factory image in the
   tftp root directory renamed to ArcherC6v2_tp_recovery.bin.
4. Connect power cable to router, press and hold the reset
   button and turn the router on
5. Keep the reset button pressed until the WPS LED lights up
6. Wait ~150 seconds to complete flashing

According to the GPL source the non-EU variant has different
GPIOs assigned to some of the LEDs and buttons. The flash
layout might be different as well. The wikidevi entry for
Archer A6/C6 assumes they are identical.

Signed-off-by: Georgi Vlaev <georgi.vlaev@gmail.com>
2018-12-31 16:25:11 +01:00
Guan-Hong Lin
9ebb44aef4 ath79: add support for EnGenius EWS511AP
EnGenius EWS511AP is a wireless managed wall AP with PoE support,
based on Qualcomm/Atheros QCA9531(Honeybee) + QCA9887.

Short specification:

- 128MB of RAM
- 16 MB of SPI FLASH
- 2T2R 2.4 GHz (QCA9531), 802.11b/g/n
- 1T1R 5 GHz (QCA9887), 802.11ac/n/a
- 2x 10/100 Mbps Ethernet (one port with PoE support)
- 1x Power LED, 2x LAN LEDs, 1x WLAN 2.4G LED, 1x WLAN 5G LED
- 1x RESET button
- built-in watchdog chipset

Flash instruction:

From EnGenius firmware to OpenWrt firmware:

Original firmware is based on QSDK.
Use sysupgrade firmware directly in vendor GUI.
Reset to factory default is necessary.

From OpenWrt firmware to EnGenius firmware:

1. Setup a TFTP server on your computer and configure static IP to 192.168.99.8
   Put the OpenWrt firmware in the root directory on your computer.
2. Power up EWS511AP. Press 4 and then press any key to enter u-boot.
3. Download OpenWrt firmware
   (ath)> tftpboot 0x80060000 ${dir}"openwrt-ath79-generic-engenius_ews511ap-squashfs-sysupgrade.bin"
4. Flash the firmware
   (ath)> erase 0x9f060000 +f50000
   (ath)> cp.b $fileaddr 0x9f060000 $filesize
5. Reboot
   (ath)> reset

Signed-off-by: Guan-Hong Lin <GH.Lin@senao.com>
2018-12-31 16:25:09 +01:00
INAGAKI Hiroshi
caf306ce91 ath79: add support for ELECOM WRC-1750GHBK2-I/C
ELECOM WRC-1750GHBK2-I/WRC-1750GHBK2-C are 2.4/5 GHz band 11ac
routers, based on Qualcomm Atheros QCA9563.

This commit also includes small fix; use "0x0x03000101" as pll_1000
instead of "0x03000000".

Specification:

- SoC:      Qualcom Atheros QCA9563
- RAM:      128 MB (DDR2)
- Flash:    16 MB (SPI-NOR)
- WLAN:     2.4/5 GHz
  - 2.4 GHz: 2T2R (SoC internal)
  - 5 GHz:   3T3R (QCA9880)
- Ethernet: 10/100/1000 Mbps
- LED/key:  4x/3x (2x buttons, 1x slide-switch)
- UART:     through-hole on PCB
  - Vcc, RX, GND, TX from switch (QCA8337N) side
  - 115200n8

Flash instruction using factory image:

1. Boot WRC-1750GHBK2-I/C normaly
2. Access to "http://192.168.2.1/" and open firmware upgrade page
("ファームウェア更新 手動更新(アップデート)")
3. Select the OpenWrt factory image and click apply ("適用") button
to perform firmware update
4. On the (initramfs) factory image, perform sysupgrade with
squashfs-sysupgrade image
5. Wait ~150 seconds to complete flashing

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-12-31 21:38:53 +09:00
David Bauer
98f826fdc0 ath79: use caldata patching for Archer C58/C59
With this commit the TP-Link Archer C58 and Archer C59 use caldata
patching in order to set the correct 5GHz MAC-address.

Tested on TP-Link Archer C59 v1.

For more details see commit 330965b.

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-12-31 13:28:31 +01:00
Christoph Krapp
af28d8a539 ath79: add support for GL.iNet GL-AR750S
Right now this patch adds nor image generation only. NAND image
generation is not supportet at the moment.

Furtheremore support for the MicroSD port is not implemented as of now.

Specification:
- SOC: QCA9563 (775MHz)
- Flash: 16 MiB (W25Q128FVSG)
- RAM: 128 MiB DDR2
- Ethernet: 2x 1Gbps LAN + 1x 1Gbps WAN
- Wireless: 2.4GHz (bgn) and 5GHz (ac)
- USB: 1x USB 2.0 port
- Button: 1x switch button, 1x reset button
- LED: 3x LEDS (green)
  - Another LED can be accessed on GPIO 7 if soldered

Flash instruction:
- Set static ip to 192.168.1.2
- Unplug the power cord
- Hold reset button
- Plug power back in
- Right led will flash 5 times
- Release reset button
- Browse to 192.168.1.1
- Choose sysupgrade image in NOR-flash section
- Press "update nor firmware"
- After successful transfer unplug network cable before device restarts

Signed-off-by: Christoph Krapp <achterin@googlemail.com>
[resolve merge conflicts, rename buttons, use switch input type for mode
switch]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-12-31 13:28:20 +01:00
Weijie Gao
abc7ed2c58 ath79: add support for D-Link DIR-859 A1
Hardware spec of DIR-859 A1:
SoC: QCA9563
DRAM: 64MB DDR2
Flash: 16MB SPI-NOR
Switch: QCA8337N
WiFi 5.8GHz: QCA9880

USB is supported on the PCB but not connected.

Flash instructions:

1. Upgrade the factory.bin through the factory web interface or the u-boot
   failsafe interface.
   The firmware will boot up correctly for the first time.
   Do not power off the device after OpenWrt has booted. Otherwise the u-boot
   will enter failsafe mode as the checksum of the firmware has been changed.
2. Upgrade the sysupgrade.bin in OpenWrt.
   After upgrading completes the u-boot won't complain about the firmware
   checksum and it's OK to use now.
3. If you powered off the device before upgrading the sysupgrade.bin, just
   upgrade the factory.bin through the u-boot failsafe interface and then goto
   step 2.

Signed-off-by: Weijie Gao <hackpascal@gmail.com>
[squash commits, use common seama recipes, sync factory image recipe
with ramips version]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-12-30 20:08:13 +01:00
David Bauer
97dc323a4c ath79: fix Archer A7 v5 5GHz MAC adress
Currently all Archer A7 v5 have the same (incorrect) MAC address.
The address is currently derived from eth1 which is not present on the
QCA9563. Use eth0 to get the correct MAC address.

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-12-29 12:35:47 +01:00
David Bauer
e67da34431 ath79: add support for devolo WiFi pro 1750c
Hardware
--------
CPU:   Qualcomm Atheros QCA9558
RAM:   128M DDR2
FLASH: 16MiB
ETH:   1x Atheros AR8035 (PoE in)
WiFi2: QCA9558 3T3R
WiFi5: QCA9880 3T3R
BTN:   1x Reset
LED:   1x LED blue
       1x LED red
BEEP:  1x GPIO attached piezo beeper
UART:  3.3V GND TX RX (115200-N-8) (3.3V is square pad)
       Header is located next to reset-button

There is also a Micro-B USB-port present but this only seems to be a
dummy as the circuit next to it is not present (at least in my unit).

It is also not mentioned in the devolo manual.

Installation
------------
Make sure you set a password for the root user as prompted on first
setup!

1. Upload OpenWRT sysupgrade image via SSH to the device.
Use /tmp as the destination folder on the device.
User is root, password the one set in the web interface.

2. Install OpenWRT with

> sysupgrade -n -F /tmp/<openwrt-image-name>

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-12-27 14:06:38 +01:00
David Bauer
1724d4e9ed ath79: add support for devolo WiFi pro 1200e
Hardware
--------
CPU:   Qualcomm Atheros QCA9558
RAM:   128M DDR2
FLASH: 16MiB
ETH:   1x Atheros AR8035 (PoE in)
       1x Atheros AR8033
WiFi2: QCA9558 2T2R
WiFi5: QCA9880 2T2R
BTN:   1x Reset
LED:   1x LED blue
       1x LED red
BEEP:  1x GPIO attached piezo beeper
UART:  3.3V GND TX RX (115200-N-8) (3.3V is square pad)
       Header is located next to reset-button

Installation
------------
Make sure you set a password for the root user as prompted on first
setup!

1. Upload OpenWRT sysupgrade image via SSH to the device.
Use /tmp as the destination folder on the device.
User is root, password the one set in the web interface.

2. Install OpenWRT with

> sysupgrade -n -F /tmp/<openwrt-image-name>

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-12-27 14:06:38 +01:00
TOCK Chiu
8471944325 ath79: add support for TP-Link Archer C7 v5
This commit adds support for TP-Link Archer C7 v5, leveraging most effort
from commit ea9baee and 1e4ee63. Archer C7 v5 is identical to Archer A7 v5
but with a different flash layout.

Specification:
-   QCA9563 SoC (750 MHz)
-   128 MiB of RAM (DDR2)
-   16 MiB of flash (SPI)
-   5x 1 Gbps Ethernet (1x WAN + 4x LAN)
-   2.4GHz (bgn) SoC internal + 5GHz (ac) QCA9880
-   10x LED, 2x button
-   UART header on PCB

Flash instructions:
1.  Upload openwrt-ath79-generic-tplink_archer-c7-v5-squashfs-factory.bin
    via web interface.

Flash instructions using TFTP recovery:
1.  Plug PC to one of the LAN ports
2.  Set PC to fixed IP address 192.168.0.66
3.  Rename the factory image to ArcherC7v5_tp_recovery.bin and place it in
    TFTP root directory
4.  Turn on the router with the reset button pressed for about 15 secs
5.  Release the button and wait about 150 secs to complete flashing

Signed-off-by: TOCK Chiu <tock.chiu@gmail.com>
2018-12-27 14:06:38 +01:00
INAGAKI Hiroshi
c566439c9b ath79: add support for NEC Aterm WG800HP
NEC Aterm WG800HP is a 2.4/5 GHz band 11ac router, based on Qualcomm
Atheros QCA9563.

Specification:

- Qualcomm Atheros QCA9563
- 64 MB of RAM (DDR2)
- 8 MB of Flash (SPI-NOR)
- 2.4/5 GHz wifi
  - 2.4 GHz: 2T2R (SoC internal)
  - 5 GHz: 1T1R (QCA9887)
- 4x 10/100/1000 Mbps Ethernet
- 8x LEDs, 3x keys (2x buttons, 1x slide-switch)
- UART through-hole on PCB (J2)
  - Vcc, GND, NC, TX, RX from SoC side
  - 115200n8

Flash instruction using factory image:

1. Connect the computer to the LAN port on WG800HP
2. Connect power cable to WG800HP and turn on it
3. Access to "http://192.168.10.1/" and open firmware update page
("ファームウェア更新")
4. Select the OpenWrt factory image and click update ("更新") button
5. Wait ~150 seconds to complete flashing

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-12-24 19:18:07 +01:00
Karl-Felix Glatzer
1e4ee63cc8 ath79: add support for TP-Link Archer A7
This patch adds support for TP-Link Archer A7

Specification:
- SOC: QCA9563
- Flash: 16 MiB (SPI)
- RAM: 128 MiB (DDR2)
- Ethernet: 4x 1Gbps LAN + 1x 1Gbps WAN
- Wireless:
  - 2.4GHz (bgn) SoC internal
  - 5GHz (ac) QCA988x
- USB: 1x USB 2.0 port
- Button: 1x power, 1x reset, 1x wps
- LED: 10x LEDs
- UART: holes in PCB
  - Vcc, GND, RX, TX from ethernet port side
  - 115200n8

Flash instructions:

Upload openwrt-ath79-generic-tplink_archer-a7-v5-squashfs-factory.bin
via the Webinterface.

Flash instruction using tftp recovery:

1. Connect the computer to one of the LAN ports of the Archer A7
2. Set the computer IP to 192.168.0.66
3. Start a tftp server with the OpenWrt factory image in the tftp
   root directory renamed to ArcherC7v5_tp_recovery.bin
2. Connect power cable to Archer A7, press and hold the reset button
   and turn the router on
3. Keep the reset button pressed for ~5 seconds
4. Wait ~150 seconds to complete flashing

Changes since first revision:

  - Flash instructions using stock image webinterface
  - Changed "Version 5" in model string to "v5"
  - Split DTS file in qca9563_tplink_archer-x7-v5.dtsi
    and qca9563_tplink_archer-a7-v5.dts
  - Firmware image is now build with dynamic partitioning
  - Default to ath10k-ct

Changes since second revision:
  - Changed uboot@0 to uboot@20000 in DTS file
  - Fixed ordering issue in board led script
  - Specify firmware partition format in DTS file
  - Rebased Makefile device definition on common
    Device/tplink-safeloader-uimage definition
  - Merged switch section in network script
    (same configuration as tplink,tl-wdr3600
    and tplink,tl-wdr4300)

Signed-off-by: Karl-Felix Glatzer <karl.glatzer@gmx.de>
2018-12-17 08:09:13 +01:00
Sebastian Kemper
6c3c4436ee ath79: add d-link dir-825-c1 and dir-835-a1
This commit ports both dir-825-c1 and dir-835-a1 from ar71xx to ath79.
They're pretty much identical, except dir-835-a1 has less LEDs.

The routers come with 128 MByte of RAM and 16 MBytes of flash and sport
2.4GHz and 5.0GHz wireless. Both routers have entries already in
OpenWrt's TOH. Please check there for more information on these
antiquities.

https://openwrt.org/toh/hwdata/d-link/d-link_dir-825_c1
https://openwrt.org/toh/hwdata/d-link/d-link_dir-835_a1

Installation:

1. Connect to the web interface of the vendor firmware (usually
   listening on 192.168.0.1).
2. Go to "Tools", then "Firmware".
3. In the "Firmware Upgrade" box click "Browse".
4. Select the OpenWrt factory image for your router.
5. Click "Upload", confirm the popups if you agree to flash the file you
   selected.
6. Wait for firmware upgrade to complete. It takes about 5 minutes.

Run-tested on dir-825-c1. dir-835-a1 should work as well, but I don't
have this router so I can't confirm.

Signed-off-by: Sebastian Kemper <sebastian_ml@gmx.net>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [trivial changes]
2018-12-17 00:21:34 +01:00
Marcin Jurkowski
3c3eaa57d9 ath79: add support for TP-Link TL-WR842N/ND v1 router
This ports support for TP-Link TL-WR842N/ND v1 from ar71xx.

CPU: Atheros AR7241 400 MHz
RAM: 32 MiB
FLASH: 8 MiB
PORTS: 4 Port 100/10 Switch, 1 Port 100/10 Wan
WiFi: Atheros AR9287
LED: SYS, WiFi, LAN, WAN, 3G, QSS
BTN: WiFi, Reset/WPS

AR71xx target used "tl-mr3420" as board id so force flag is needed
if upgrading from old target.

Signed-off-by: Marcin Jurkowski <marcin1j@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [trivial cleanup]
2018-12-15 21:35:45 +01:00
INAGAKI Hiroshi
3358cae523 ath79: add support for I-O DATA WN-AG300DGR
I-O DATA WN-AG300DGR is a 2T2R 2.4/5 GHz 11n router, based on Atheros
AR1022.

WN-AG300DGR does not have an LED to indicates power or system status,
I set "router" LED as OpenWrt status LED.

There is no eeprom data for 5 GHz wlan in "art" partition.

Specification:

- Atheros AR1022
- 64 MB of RAM (DDR2)
- 8 MB of Flash (SPI-NOR)
- 2T2R 2.4/5GHz wifi
  - 2.4 GHz: SoC internal
  - 5 GHz: Atheros AR93x2
- 5x 10/100/1000 Mbps Ethernet
- 6x LEDs, 6x keys (4x buttons, 1x slide switch)
- 1x USB 2.0 Type-A
- UART through-hole on PCB
  - Vcc, GND, TX, RX from ethernet port side
  - 115200n8

Flash instruction using factory image:

1. Connect the computer to the LAN port on WN-AG300DGR
2. Connect power cable to WN-AG300DGR and turn it
3. Access to "http://192.168.0.1/" and open firmware update page
("ファームウェア")
4. Select the OpenWrt factory image and click update ("更新") button
5. Wait ~150 seconds to complete flashing

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-12-06 20:26:57 +01:00
Chuanhong Guo
9dd7147f6b ath79: add support for Winchannel WB2000
WB2000 is a dual-band 11N AP using AR9344.
The factory firmware used the original DB120 partition table
with a small kernel partition at the end of firmware and the
kernel will easily get oversized in the future. Since it has
to be flashed using UART I also swapped kernel/rootfs and
changed the default load address.

Specification:

- SoC: Atheros AR9344
- RAM: 128 MB
- Flash: 16 MB
- Ethernet: 10/100/1000 Mbps (Atheros AR8035)
- 2x USB 2.0
- WIFI: AR9344(2G) + AR9382(5G)
- RTC: DS1338

Known issue:
5G ath9k led doesn't work due to commit ccab68f.

Flash instruction:
Set up a TFTP server on your computer and configure static IP.
Connect UART (J11 TX/GND/RX) and press any key to enter U-boot
shell.
1. Change the default boot command:
   setenv bootcmd 'bootm 0x9f050000 || bootm 0x9fd50000'
   saveenv
2. Set your router ipaddr and server ipaddr. e.g.:
   setenv ipaddr 192.168.1.1
   setenv serverip 192.168.1.50
3. Load and flash the firmware:
   tftp 0x80060000 fw.bin
   erase 0x9f050000 +$filesize
   cp.b $fileaddr 0x9f050000 $filesize
4. Reset your router:
   reset

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
[Drop the i2c node unit address. Move the ath9k-leds node out of the spi
node, it doesn't belong there. Add the #gpio-cells property to the pci
wifi node. All fix dtc compiler warnings]
Signed-off-by: Mathias Kresin <dev@kresin.me>

merge
2018-12-06 20:26:30 +01:00
Russell Senior
73127a878d ath79: add support for Ubiquiti AirRouter
Indoor low-power router with 2.4 GHz radio

CPU:    Atheros AR7241 rev 1
RAM:    32 MB
Flash:  8 MB NOR SPI
Switch: Atheros AR7240
Ports:  1x WAN, 4x LAN 10/100 Ethernet
WLAN:   Atheros AR9285 (2.4 GHz)
USB:    1x USB2 host port

Note: Ethernet WAN/LAN port naming is reversed from ar71xx.
WAN is eth0; LAN is eth1.1.

UART settings: 115200, 8N1

                LEDs
        +--------------------------
        |
        |
        |
        |
        |
        |
        |
        |
    VCC | x x
     RX | * x
        | x x
        | x x
     TX | * x
    GND | * x
        |
        |
        |
        |
        +--------------------------
                ETHERNET PORTS

Installation from Ubiquiti firmware, is as for other ubnt-xm AirOs devices.

Signed-off-by: Russell Senior <russell@personaltelco.net>
2018-12-03 07:58:56 +01:00
Mathias Kresin
68d77241cd ath79: rename glinet x750
The boardname is gl-x750 and is already used for the led names.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-11-27 21:11:54 +01:00
David Bauer
946ffe470d ath79: add support for Archer C58/C59 v1
This commit adds support for the Archer C58 v1 and C59 v1, previously
supported in the ar71xx target.

CPU:   Qualcomm QCA9561
RAM:   64M (C58) / 128M (C59)
FLASH: 8M (C58) / 16M (C59)
WiFi:  QCA9561 bgn 3x3:3
       QCA9888 nac 2x2:2
LED:   Power, WiFi 2.4, WiFi 5, WAN green, WAN amber, LAN, WPS
       Only C59: USB
BTN:   WPS, WiFi, Reset

Installation
------------

Via Web-UI:
Update factory image via Web-UI.

Via TFTP:
Rename factory image to "tp_recovery.bin" and place it in the root-dir
of your tftp server. Configure to listen on 192.168.0.66. Power up the
router while holding down the reset-button. The router will flash itself
and reboot.

Note: For TFTP, you might need a switch between router and computer, as
link establishment might take to long.

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-11-26 12:05:45 +01:00
Luo chongjun
9989fd5154 ath79: add support for GL-iNet GL-X750
this patch adds supports for GL-X750.

Specification:
- SOC: QCA9531 (650MHz)
- Flash: 16 MiB (W25Q128FVSG)
- RAM: 128 MiB DDR2
- Ethernet: 10/100: 1xLAN + 10/100: 1xWAN
- Wireless: 2.4GHz (bgn) and 5GHz (ac)
- USB: 1x USB 2.0 port
- Button: 1x reset button
- LED: 5x LEDS (green)

Flash instruction:
The original firmware is openwrt, so both LuCI or sysupgrade can be used.

Signed-off-by: Luo chongjun <luochongjun@gl-inet.com>
2018-11-26 12:05:45 +01:00
YuheiOKAWA
27eae6597e ath79: add support for PQI Air Pen
SoC: AR9330 (or AR9331 revision?)
Ethernet x1, Wireless 2.4G, uSD card slot x1.
USB Power, include Li-Po Battery.

Flash 8MiB. (factory is dual image)
1. write image is use half 4MiB size from factory.
  write initramfs image to mtd6 and mtd7.
2. change next boot setting. next is mtd6 boot.
  echo -ne "\x01" | dd of=/dev/mtdblock8 conv=notrunc bs=1 count=1 seek=0

3. rewrite sysupgrade image.
  change next boot setting. next is mtd4.
  echo -ne "\x00" | dd of=/dev/mtdblock8 conv=notrunc bs=1 count=1 seek=0

OEM mtd.
dev:    size   erasesize  name
mtd0: 00040000 00010000 "u-boot"
mtd1: 00010000 00010000 "u-boot-env"
mtd2: 00010000 00010000 "ART"
mtd3: 00010000 00010000 "NVRAM"
mtd4: 00140000 00010000 "uImage"
mtd5: 00280000 00010000 "rootfs"
mtd6: 00140000 00010000 "uImage2"
mtd7: 00280000 00010000 "rootfs2"
mtd8: 00010000 00010000 "CONF"

Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>
2018-10-28 10:59:14 +01:00
Roger Pueyo Centelles
23f9b2d9a9 ath79: Add support for Ubiquiti LiteAP ac (LAP-120)
This commit adds support for the Ubiquiti LiteAP ac (LAP-120), an outdoor
5 GHz AC access point with an integrated 120° 16 dBi antenna. The device
was previously known as LiteBeam AP ac but was later rebranded.

CPU:    Atheros AR9342 SoC
RAM:    64 MB DDR2
Flash:  16 MB NOR SPI
Ports:  1 GbE port (PoE in)
WLAN:   5 GHz QCA899X (PCI)

The integrated QCA899X is a Ubiquiti branded part with modified vendor
and product id (0777:11ac9). It is very similar to the NanoStation loco
AC, except for the 2.4 GHz management radio (missing here).

Installation procedure is the same as the NanoStation [loco] AC:

1. Connect to serial header on device
2. Power on device and enter uboot console
3. Set up tftp server serving an openwrt initramfs build
4. Load initramfs build using the command tftpboot in the uboot cli
5. Boot the loaded image using the command bootm
6. Copy squashfs openwrt sysupgrade build to the booted device
7. Use mtd to write sysupgrade to partition "firmware"
8. Reboot and enjoy

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
2018-10-28 10:59:09 +01:00