Commit Graph

55013 Commits

Author SHA1 Message Date
Thomas Langer
0e3911b608 kernel: netsupport: Extract sched-prio and sched-red
Extract the kmod-sched-prio and kmod-sched-red kernel modules from the
big kmod-sched package. This allows adding the two kernel modules to
OpenWrt without adding the kmod-sched and all its depdnecy.

Signed-off-by: Thomas Langer <tlanger@maxlinear.com>
Signed-off-by: Hauke Mehrtens <hmehrtens@maxlinear.com>
2022-08-06 21:32:35 +02:00
Hauke Mehrtens
fa85e44d3c kernel: netsupport: Add kmod-sched-drr
This adds a package with the DRR scheduler.

Signed-off-by: Hauke Mehrtens <hmehrtens@maxlinear.com>
2022-08-06 21:32:35 +02:00
Hauke Mehrtens
c94ba95e6c kernel: netsupport: kmod-sched: Reorder packages
This puts the kmod-sched packages into an alphabetical order.
I kept the kmod-sched-core at the top as this is the main package.
No changes other than reordering were done.

Signed-off-by: Hauke Mehrtens <hmehrtens@maxlinear.com>
2022-08-06 21:32:35 +02:00
Thomas Langer
1b956e66cc kernel: netsupport: kmod-sched: explicitly define included modules
Change SCHED_MODULES_EXTRA to an explicit list of modules
instead of taking everything that is not filtered out.
This removes the need of updating the filter each time an extra
sch_*, act_* or similar is added with an own kmod definition.

Signed-off-by: Thomas Langer <tlanger@maxlinear.com>
Signed-off-by: Hauke Mehrtens <hmehrtens@maxlinear.com>
2022-08-06 21:32:35 +02:00
Hauke Mehrtens
3cc878a8d3 kernel: netsupport: kmod-sched: Add kmod-lib-textsearch dependency
The CONFIG_NET_EMATCH_TEXT configuration option depends on the
kmod-lib-textsearch package.

Signed-off-by: Hauke Mehrtens <hmehrtens@maxlinear.com>
2022-08-06 21:32:35 +02:00
Hauke Mehrtens
606e357bf8 kernel: netsupport: kmod-sched: Remove sch_fq_codel and sch_fifo
The sch_fq_codel.ko and the sch_fifo.ko are always compiled into the
kernel, they are activated in the generic kernel configuration. There is
no need to activate the build of these kernel modules in the kmod-sched*
packages.

Signed-off-by: Hauke Mehrtens <hmehrtens@maxlinear.com>
2022-08-06 21:32:35 +02:00
André Valentin
2cc5059240 ramips: add support for ZyXEL LTE3301-Plus
The ZyXEL LTE3301-PLUS is an 4G indoor CPE with 2 external LTE antennas.

Specifications:

 - SoC: MediaTek MT7621AT
 - RAM: 256 MB
 - Flash: 128 MB MB NAND (MX30LF1G18AC)
 - WiFi: MediaTek MT7615E
 - Switch: 4 LAN ports (Gigabit)
 - LTE: Quectel EG506 connected by USB3 to SoC
 - SIM: 1 micro-SIM slot
 - USB: USB3 port
 - Buttons: Reset, WPS
 - LEDs: Multicolour power, internet, LTE, signal, Wifi, USB
 - Power: 12V, 1.5A

The device is built as an indoor ethernet to LTE bridge or router with
Wifi.

UART Serial:

57600N1
Located on populated 5 pin header J5:

 [o] GND
 [ ] key - no pin
 [o] RX
 [o] TX
 [o] 3.3V Vcc

MAC assignment:
lan:  98:0d:67:ee:85:54 (base, on the device back)
wlan: 98:0d:67:ee:85:55

Installation from web GUI:

- Log in as "admin" on http://192.168.1.1/
- Upload OpenWrt initramfs-recovery.bin image on the
  Maintenance -> Firmware page
- Wait for OpenWrt to boot and ssh to root@192.168.1.1
- format ubi device: ubiformat /dev/mtd6
- attach ubi device: ubiattach -m6
- create rootfs volume: ubimkvol /dev/ubi0 -n0 -N rootfs -s 1MiB
- rootfs_data volume: ubimkvol /dev/ubi0 -n1 -N rootfs_data -s 1MiB
- run sysupgrade with sysupgrade image

For more details about flashing see
commit 2449a63208 ("ramips: mt7621: Add support for ZyXEL NR7101").

Please note that this commit is needed:
firmware-utils: add marcant changes for ZyXEL NBG6716 and LTE3301-PLUS

Signed-off-by: André Valentin <avalentin@marcant.net>
2022-08-06 20:33:59 +02:00
Manuel Niekamp
0dc5821489 ath79: add support for Sophos AP15
The Sophos AP15 seems to be very close to Sophos AP55/AP100.

Based on:
commit 6f1efb2898 ("ath79: add support for Sophos AP100/AP55 family")
author    Andrew Powers-Holmes <andrew@omnom.net>
          Fri, 3 Sep 2021 15:53:57 +0200 (23:53 +1000)
committer Hauke Mehrtens <hauke@hauke-m.de>
          Sat, 16 Apr 2022 16:59:29 +0200 (16:59 +0200)

Unique to AP15:
 - Green and yellow LED
 - 2T2R 2.4GHz 802.11b/g/n via SoC WMAC
 - No buttons
 - No piezo beeper
 - No 5.8GHz

Flashing instructions:
 - Derived from UART method described in referenced commit, methods
   described there should work too.
 - Set up a TFTP server; IP address has to be 192.168.99.8/24
 - Copy the firmware (initramfs-kernel) to your TFTP server directory
   renaming it to e.g. boot.bin
 - Open AP's enclosure and locate UART header (there is a video online)
 - Terminal connection parameters are 115200 8/N/1
 - Connect TFTP server and AP via ethernet
 - Power up AP and cancel autoboot when prompted
 - Prompt shows 'ath> '
 - Commands used to boot:
    ath> tftpboot 0x81000000 boot.bin
    ath> bootm 0x81000000
 - Device should boot OpenWRT
 - IP address after boot is 192.168.1.1/24
 - Connect to device via browser
 - Permanently flash using the web ui (flashing sysupgrade image)
 - (BTW: the AP55 images seem to work too, only LEDs are not working)

Testing done:
 - To be honest: Currently not so much testing done.
 - Flashed onto two devices
 - Devices are booting
 - MAC addresses are correct
 - LEDs are working
 - Scanning for WLANs is working

Big thanks to all the people working on this great project!
(Sorry about my english, it is not my native language)

Signed-off-by: Manuel Niekamp <m.niekamp@richter-leiterplatten.de>
2022-08-06 20:33:59 +02:00
Jan-Niklas Burfeind
75dffdc8cf ath79: add variant UniFi AP LR
The hardware difference is the antenna which has a higher gain compared
to the original UniFi AP.

The variant was supported before in ar71xx.

Signed-off-by: Jan-Niklas Burfeind <git@aiyionpri.me>
2022-08-06 20:15:30 +02:00
Jan-Niklas Burfeind
50e1f3d84d ath79: rename references of UniFi to UniFi AP
extract the compatible and model to make room for other variants

follow-up of
commit dc23df8a8c ("ath79: change Ubiquiti UniFi AP model name to include "AP"")

Signed-off-by: Jan-Niklas Burfeind <git@aiyionpri.me>
2022-08-06 20:15:30 +02:00
Reto Schneider
2293f1abe4 ramips: mt7628: fix memory controller reset bit
According to MediaTek MT7688 Datasheet v1.4, as well as the MT7628
counterpart, the memory controller reset bit (MC_RST) is 10, not 20.
Reset bit 20 is used for for UART 2 (UART2_RST).

Please note: Due to the lack of hardware, I was not able to test this
change.

Signed-off-by: Reto Schneider <reto.schneider@husqvarnagroup.com>
2022-08-06 19:58:46 +02:00
David Yang
577f3fdbc9 ramips: add support for Netcore NW5212
This patch adds support for Netcore NW5212, provided by some carrier in
China.

Specifications:
--------------

* SoC: Mediatek MT7620A
* RAM: 128MB DDR2
* Flash: 16MB SPI NOR flash (Winbond W25Q128BV)
* WiFi 2.4GHz: builtin
* Ethernet: builtin
* LED: Power, WAN, LAN 1-4, WiFi
* Buttons: Reset (GPIO 13)
* UART: Serial console (57600 8n1)
* USB: 1 x USB2

Installation:
------------

The router comes with OpenWrt 14.07 built with MTK SDK. However, as the
modem is provided by carriers, so the web interface is highly minimized and
only contains a static page with no interaction options.

There are two possible ways to gain the access.

1) Open the shell and use a UART2USB convert to gain TTY access. Please
   notice you have to remove resistance R54 at the back of the board
   otherwise you won't be able to input anything.
2) Use built-in backdoor. Access http://192.168.1.1/cgi-bin/_/testxst to
   start dropbear service at port 9122. Be warned the software is super
   old and only diffie-hellman-group1-sha1, diffie-hellman-group14-sha1,
   kexguess2@matt.ucc.asn.au is support, you may not be able to connect it
   with an up-to-date ssh client.

After you can control the device, flash the firmware as usual. Here are
some hints for that.

Option 1 (via original firmware):

1) Setup HTTP server on your computer, for example:
     python3 -m http.server
2) Connect to the route and flash:
     cd /tmp
     wget http://<your-computer-host>/<your-firmware-name>
     mtd -r write <your-firmware-name> firmware

Option 2 (replacing u-boot via breed):

1) Download breed-mt7620-reset13.bin from https://breed.hackpascal.net/
2) Setup HTTP server on your computer, for example:
     python3 -m http.server
   You can skip this step if your breed is already accessible from HTTP,
   since the original wget does not support HTTPS.
3) Connect to the route and flash breed:
     cd /tmp
     wget http://<your-computer-host>/breed-mt7620-reset13.bin
     mtd write breed-mt7620-reset13.bin Bootloader
4) Reboot. Hold reset key or press any key in TTY to enter breed.
5) Access breed web interface (http://192.168.1.1/). Choose the flash
   layout to be 0x50000 and flash new firmware.

MAC addresses:
-------------

There are three MACs stored in factory, as in MT7620A reference design:

source address   usage
   0x4 label     WLAN
  0x28 label     MAC 1
  0x2e label + 1 MAC 2

However, the OEM firmware only uses one single MAC (label) for all
interfaces, probably a misconfiguration.

Signed-off-by: David Yang <mmyangfl@gmail.com>
2022-08-06 19:58:46 +02:00
David Yang
b00a02aaa0 ramips: add support for Netgear PR2000
This patch adds support for Netgear PR2000, sold as "Travel Router and
Range Extender".

Specifications:
--------------

* SoC: Mediatek MT7620N
* RAM: 64MB DDR2
* Flash: 16MB SPI NOR flash (Macronix MX25L12805D)
* WiFi 2.4GHz: builtin
* Ethernet: builtin
* LED: Power, Internet, WiFi, USB
* Buttons: Reset (GPIO 1/2)
* UART: Serial console (57600 8n1)
* USB: 1 x USB2

SPECIAL NOTES:
-------------

Problem: WiFi is super weak, but SSID beacons seems to be right.

Solve: Change 36h in factory partition (namely 0xf60036) to be 0x0.

Explain: Clearly Netgear have different ideas on how EEPROM is used. Bit 2
of 36h indicates the presence of External LNA for 11g (2.4 GHz) band,
which seems to be incorrectly set by Netgear (originally 0x04). Lifting it
solves the problem of weak RX signal.

Installation:
------------

There are two possible ways to install the firmware. Flashing via web
interface of original firmware is not tested due to a broken firmware.

1) Open the shell and use a UART2USB convert to gain TTY access (TP7: RXD,
   TP9: TXD, TP10: GND). Please notice you have to remove resistance R54
   next to TP7 otherwise you won't be able to input anything.
2) Use well-known Netgear debug switch. Access
   http://192.168.168.1/setup.cgi?todo=debug to start telnet service
   (username: root, password: <none>).

Please back up firmware if you want to go back to the original.

After you can control the device, flash the firmware as usual. Here are
some hints for that.

Option 1 (via nmrpflash):

1) Download nmrpflash from https://github.com/jclehner/nmrpflash
2) Use *-factory.img and flash:
     nmrpflash -L
     nmrpflash -i net* -f <your-firmware-name>
3) Turn off then turn on the device, wait it finishing flash.

Option 2 (replacing u-boot via breed):

1) Download breed-mt7620-reset1.bin from https://breed.hackpascal.net/
2) Setup HTTP server on your computer, for example:
     python3 -m http.server
   You can skip this step if your breed is already accessible from HTTP,
   since the original wget does not support HTTPS.
3) Connect to the route and flash breed:
     cd /tmp
     wget http://<your-computer-host>/breed-mt7620-reset1.bin
     dd if=breed-mt7620-reset1.bin of=/dev/mtdblock0 bs=64k
4) Reboot. Hold reset key or press any key in TTY to enter breed.
5) Access breed web interface (http://192.168.1.1/). Choose memory layout
   to be 0x40000 and flash new firmware.

Remark:
------

As a "Range Extender", it has a switch to switch between Wired mode (GPIO
21 low) and Wireless mode (GPIO 20 low), which is not implemented in this
patch. However, the router will be turned off when it switches to the
middle, which makes this switch much less useful.

MAC addresses:
-------------

The OEM firmware uses one single MAC for all interfaces, located at
0xf700b0.

Signed-off-by: David Yang <mmyangfl@gmail.com>
2022-08-06 19:58:46 +02:00
Lea Teuberth
45255aa0e8 ramips: adding support for Asus RP-AC56
Specifications:
	CPU:     MT7621A dual-core 880MHz
	RAM:     64MB DDR2
	FLASH:   16MB MX25L12805D NOR SPI
	WIFI:    2.4GHz 2x2 MT7603 b/g/n PCI
	WIFI:    5GHz 2x2 MT7662 a/b/ac PCI
	ETH:     1xLAN 1000base-T integrated
	SWITCH:  MT7530 Port 0: LAN, Port 6: CPU
	LED:     Power, 2.4GHz WiFi, 5GHz WiFi
	BTN:     WPS, Reset
	UART:    Near ETH port, from ETH: 3V3-TxD-GND-RxD 57600 8n1
	MISC:    Audio support

Installation:
	1. Update using recovery mode
	   - while holdig "reset" button, power on the device
	   - keep holding "reset" until power led is flashing yellow
	   - set own IP to 192.168.1.75, subnet mask: 255.255.255.0
	   - push firmware image (can be factory.bin or sysupgrade.bin)
	     using tftp client in binary mode to 192.168.1.1

Notes:
	This board has only two MAC addresses programmed in the "factory" partition:
	- MAC for wlan0 (2.4GHz) at offset 0x0004
	- MAC for wlan1 (5GHz) at offset 0x8004
	- stock firmware re-uses wlan0 MAC for ethernet
	- no valid addresses found in 0x28, 0x2e, 0xe000 and 0xe006

Signed-off-by: Lea Teuberth <lea.teuberth@outlook.com>
2022-08-06 19:58:46 +02:00
Nick Hainke
9edda3169f trace-cmd: update to v3.1.2
Remove outdated patches:
- 100-musl.patch
- 110-mac80211_tracepoint.patch

Trace-cmd now uses libtracefs and livtraceevent as libraries.
The plugins moved to libtraceevent.

Signed-off-by: Nick Hainke <vincent@systemli.org>
2022-08-06 19:58:46 +02:00
Nick Hainke
6d84e78cd9 libtracefs: add Linux kernel trace file system library
Needed by trace-cmd.

Signed-off-by: Nick Hainke <vincent@systemli.org>
2022-08-06 19:58:46 +02:00
Nick Hainke
b108810601 libtraceevent: add Linux kernel trace event library
Needed by trace-cmd.

Signed-off-by: Nick Hainke <vincent@systemli.org>
2022-08-06 19:58:46 +02:00
Nick Hainke
0cb1ce9748 elfutils: update to 0.187
Changes:
debuginfod: Support -C option for connection thread pooling.

debuginfod-client: Negative cache file are now zero sized instead of
                   no-permission files.

addr2line: The -A, --absolute option, which shows file names including
           the full compilation directory is now the default.  To get the
           old behavior use the new option --relative.

readelf, elflint: Recognize FDO Packaging Metadata ELF notes

libdw, debuginfo-client: Load libcurl lazily only when files need to
                         be fetched remotely. libcurl is now never
                         loaded when DEBUGINFOD_URLS is unset. And when
                         DEBUGINFOD_URLS is set, libcurl is only loaded
                         when the debuginfod_begin function is called.

Signed-off-by: Nick Hainke <vincent@systemli.org>
2022-08-06 19:58:46 +02:00
Olliver Schinagl
404cad6470 base-files: LED/trigger/heartbeat: Add support for inversion
The heartbeat trigger has the option to be inverted, however
openwrt/uci/luci have no way to set this.

This patch adds this support.

Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
2022-08-06 19:58:46 +02:00
Olliver Schinagl
b8f27251c9 base-files: LED/gpio: Ensure inverted is read as a boolean
The sysfs interface for the GPIO takes a boolean value. Ensure we get
one from uci.

Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
2022-08-06 19:58:46 +02:00
John Audia
ccff2fbaea kernel: bump 5.10 to 5.10.135
All patches automatically rebased.

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-08-06 19:58:46 +02:00
John Audia
122b625e74 kernel: bump 5.15 to 5.15.59
Patches automatically rebased.

Build system: x86_64
Build-tested: bcm2711/RPi4B, mt7622/RT3200
Run-tested: bcm2711/RPi4B, mt7622/RT3200

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-08-06 19:58:46 +02:00
Petr Štetiar
7df6795d4c zlib: backport fix for heap-based buffer over-read (CVE-2022-37434)
zlib through 1.2.12 has a heap-based buffer over-read or buffer overflow
in inflate in inflate.c via a large gzip header extra field. NOTE: only
applications that call inflateGetHeader are affected. Some common
applications bundle the affected zlib source code but may be unable to
call inflateGetHeader.

Fixes: CVE-2022-37434
References: https://github.com/ivd38/zlib_overflow
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2022-08-06 15:00:08 +02:00
Petr Štetiar
98df6bd99c generic: 5.15: disable CONFIG_DEBUG_INFO_REDUCED symbol
This came up during build testing of mvebu/cortexa9 target with 5.15
kernel.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2022-08-06 15:00:08 +02:00
INAGAKI Hiroshi
cef3f05a55 realtek: add support for Panasonic Switch-M48eG PN28480K
Panasonic Switch-M48eG PN28480K is a 48 + 4 port gigabit switch, based on
RTL8393M.

Specification:

- SoC           : Realtek RTL8393M
- RAM           : DDR3 128 MiB (Winbond W631GG8KB-15)
- Flash         : SPI-NOR 32 MiB (Macronix MX25L25635FMI-10G)
- Ethernet      : 10/100/1000 Mbps x48 + 2
  - port  1-40  : TP, RTL8218B x5
  - port 41-48  : RTL8218FB
    - port 41-44: TP
    - port 45-48: TP/SFP (Combo)
- LEDs/Keys     : 7x / 1x
- UART          : RS-232 port on the front panel (connector: RJ-45)
  - 3:TX, 4:GND, 5:GND, 6:RX (pin number: RJ-45)
  - 9600n8
- Power         : 100-240 VAC, 50/60 Hz, 0.5 A
  - Plug        : IEC 60320-C13
- Stock OS      : VxWorks based

Flash instruction using initramfs image:

1.  Prepare the TFTP server with the IP address 192.168.1.111
2.  Rename the OpenWrt initramfs image to "0101A8C0.img" and place it to
    the TFTP directory
3.  Download the official upgrading firmware (ex: pn28480k_v30000.rom)
    and place it to the TFTP directory
4.  Boot M48eG and interrupt the U-Boot with Ctrl + C keys
5.  Execute the following commands and boot with the OpenWrt initramfs
    image

    rtk network on
    tftpboot 0x81000000
    bootm

6.  Backup mtdblock files to the computer by scp or anything and reboot
7.  Interrupt the U-Boot and execute the following commands to re-create
    filesystem in the flash

    ffsmount c:/
    ffsfmt c:/

    this step takes a long time, about ~ 4 mins

8.  Execute the following commands to put the official images to the
    filesystem

    updatert <official image>

    example:

      updatert pn28480k_v30000.rom

    this step takes about ~ 40 secs

9.  Set the environment variables of the U-Boot by the following commands

    setenv loadaddr 0xb4e00000
    setenv bootcmd 'sleep 10; bootm;'
    saveenv

    'sleep 10;' is required as dummy to execute 'bootm' command correctly

10: Download the OpenWrt initramfs image and boot with it

    tftpboot 0x81000000 0101A8C0.img
    bootm

11: On the initramfs image, download the sysupgrade image and perform
    sysupgrade with it

    sysupgrade <imagename>

12: Wait ~ 120 seconds to complete flashing

Known Issues:

- 4x SFP ports are provided as combo ports by the RTL8218FB chip, but the
  phy driver has no support for it. Currently, only TP ports work by the
  RTL8218B support.

Note:

- "Switch-M48eG" is a model name, and "PN28480K" is a model number.
  Switch-M48eG has an another (old) model number ("PN28480"), it's not a
  Realtek based hardware.

- Switch-M48eG has a "POWER" LED (Green), but it's not connected to any
  GPIO pin.

- U-Boot checks the runtime images in the flash when booting and fails
  to execute "bootcmd" variable if the images are not existing.

- A filesystem is formed in the flash (0x100000-0x1DFFFFF) on the stock
  firmware and it includes the stock images, configuration files and
  checksum files. It's unknown format, can't be managed on the OpenWrt.
  To get the enough space for OpenWrt, move the filesystem to the head
  of "fs_reserved" partition by execution of "ffsfmt" and "updatert".

- A GPIO pin on PCA9539 is used for resetting external RTL8218B phys and
  RTL8218FB phy.
  This should be specified as "reset-gpios" property in MDIO node, but
  the current configuration of RTL8218B phy in the driver seems to be
  incomplete and RTL8218FB won't be configured on RTL8218D support.
  So, ethernet ports on these phys will be broken after hard-resetting.
  At the moment, configure this pin as gpio-hog to avoid breaking by
  resetting.

- This model has 2x Microchip TCN75A thermal sensors. Linux Kernel
  supports TCN75 chip on lm75 driver, but no support for TCN75'A'
  variant.
  At the moment, use TCN75 support for the chips instead.

Back to the stock firmware:

1. Delete "loadaddr" variable and set "bootcmd" to the original value

   on U-Boot:

     setenv loadaddr
     setenv bootcmd 'ffsrdm c:/runtime.had 0x81000000;alphadec c:/runtime.had 0x81000240 0x80010000;'

   on OpenWrt:

     fw_setenv loadaddr
     fw_setenv bootcmd 'ffsrdm c:/runtime.had 0x81000000;alphadec c:/runtime.had 0x81000240 0x80010000;'

2. Perform reset or reboot

  on U-Boot:

    reset

  on OpenWrt:

    reboot

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2022-08-06 14:39:57 +02:00
INAGAKI Hiroshi
4974ee7341 realtek: enable pca953x GPIO driver for rtl839x subtarget
The system status LED on Panasonic Switch-M48eG PN28480K is connected to
a PCA9539PW. To use the LED as a status LED of OpenWrt while booting,
enable the pca953x driver and built-in to the kernel.
Also enable CONFIG_GPIO_PCA953X_IRQ to use interrupt via RTL83xx GPIO.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2022-08-06 14:39:57 +02:00
INAGAKI Hiroshi
fa52e5e254 realtek: add support for Panasonic Switch-M24eG PN28240K
Panasonic Switch-M24eG PN28240K is a 24 + 2 port gigabit switch, based on
RTL8382M.

Specification:

- SoC           : Realtek RTL8382M
- RAM           : DDR3 128 MiB (Winbond W631GG8KB-15)
- Flash         : SPI-NOR 32 MiB (Macronix MX25L25635FMI-10G)
- Ethernet      : 10/100/1000 Mbps x24 + 2
  - port  1-8   : TP, RTL8218B
  - port  9-16  : TP, RTL8218B (SoC)
  - port 17-24  : RTL8218FB
    - port 17-22: TP
    - port 23-24: TP/SFP (Combo)
- LEDs/Keys     : 7x / 1x
- UART          : RS-232 port on the front panel (connector: RJ-45)
  - 3:TX, 4:GND, 5:GND, 6:RX (pin number: RJ-45)
  - 9600n8
- Power         : 100-240 VAC, 50/60 Hz, 0.5 A
  - Plug        : IEC 60320-C13
- Stock OS      : VxWorks based

Flash instruction using initramfs image:

1.  Prepare the TFTP server with the IP address 192.168.1.111
2.  Rename the OpenWrt initramfs image to "0101A8C0.img" and place it to
    the TFTP directory
3.  Download the official upgrading firmware (ex: pn28240k_v30000.rom)
    and place it to the TFTP directory
4.  Boot M24eG and interrupt the U-Boot with Ctrl + C keys
5.  Execute the following commands and boot with the OpenWrt initramfs
    image

    rtk network on
    tftpboot 0x81000000
    bootm

6.  Backup mtdblock files to the computer by scp or anything and reboot
7.  Interrupt the U-Boot and execute the following commands to re-create
    filesystem in the flash

    ffsmount c:/
    ffsfmt c:/

    this step takes a long time, about ~ 4 mins

8.  Execute the following commands to put the official images to the
    filesystem

    updatert <official image>

    example:

      updatert pn28240k_v30000.rom

    this step takes about ~ 40 secs

9.  Set the environment variables of the U-Boot by the following commands

    setenv loadaddr 0xb4e00000
    setenv bootcmd bootm
    saveenv

10: Download the OpenWrt initramfs image and boot with it

    tftpboot 0x81000000 0101A8C0.img
    bootm

11: On the initramfs image, download the sysupgrade image and perform
    sysupgrade with it

    sysupgrade <imagename>

12: Wait ~ 120 seconds to complete flashing

Known Issues:

- 2x SFP ports are provided as combo ports by the RTL8218FB chip, but the
  phy driver has no support for it. Currently, only TP ports work by the
  RTL8218D support.

Note:

- "Switch-M24eG" is a model name, and "PN28240K" is a model number.
  Switch-M24eG has an another (old) model number ("PN28240"), it's not a
  Realtek based hardware.

- Switch-M24eG has a "POWER" LED (Green), but it's not connected to any
  GPIO pin.

- U-Boot checks the runtime images in the flash when booting and fails
  to execute "bootcmd" variable if the images are not existing.

- A filesystem is formed in the flash (0x100000-0x1DFFFFF) on the stock
  firmware and it includes the stock images, configuration files and
  checksum files. It's unknown format, can't be managed on the OpenWrt.
  To get the enough space for OpenWrt, move the filesystem to the head
  of "fs_reserved" partition by execution of "ffsfmt" and "updatert".

- A GPIO pin on PCA9539 is used for resetting external RTL8218B phy and
  RTL8218FB phy.
  This should be specified as "reset-gpios" property in MDIO node, but
  the current configuration of RTL8218B phy in the phy driver seems to
  be incomplete and RTL8218FB won't be configured on RTL8218D support.
  So, ethernet ports on these phys will be broken after hard-resetting.
  At the moment, configure this pin as gpio-hog to avoid breaking by
  resetting.

Back to the stock firmware:

1. Delete "loadaddr" variable and set "bootcmd" to the original value

   on U-Boot:

     setenv loadaddr
     setenv bootcmd 'bootm 0x81000000'

   on OpenWrt:

     fw_setenv loadaddr
     fw_setenv bootcmd 'bootm 0x81000000'

2. Perform reset or reboot

  on U-Boot:

    reset

  on OpenWrt:

    reboot

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2022-08-06 14:39:57 +02:00
INAGAKI Hiroshi
3d669ec9cd realtek: add support for Panasonic Switch-M16eG PN28160K
Panasonic Switch-M16eG PN28160K is a 16 + 2 port gigabit switch, based on
RTL8382M.

Specification:

- SoC           : Realtek RTL8382M
- RAM           : DDR3 128 MiB (Winbond W631GG8KB-15)
- Flash         : SPI-NOR 32 MiB (Macronix MX25L25635FMI-10G)
- Ethernet      : 10/100/1000 Mbps x16 + 2
  - port 1-8    : TP, RTL8218B (SoC)
  - port 9-16   : RTL8218FB
    - port  9-14: TP
    - port 15-16: TP/SFP (Combo)
- LEDs/Keys     : 7x / 1x
- UART          : RS-232 port on the front panel (connector: RJ-45)
  - 3:TX, 4:GND, 5:GND, 6:RX (pin number: RJ-45)
  - 9600n8
- Power         : 100-240 VAC, 50/60 Hz, 0.5 A
  - Plug        : IEC 60320-C13
- Stock OS      : VxWorks based

Flash instruction using initramfs image:

1.  Prepare the TFTP server with the IP address 192.168.1.111
2.  Rename the OpenWrt initramfs image to "0101A8C0.img" and place it to
    the TFTP directory
3.  Download the official upgrading firmware (ex: pn28160k_v30003.rom)
    and place it to the TFTP directory
4.  Boot M16eG and interrupt the U-Boot with Ctrl + C keys
5.  Execute the following commands and boot with the OpenWrt initramfs
    image

    rtk network on
    tftpboot 0x81000000
    bootm

6.  Backup mtdblock files to the computer by scp or anything and reboot
7.  Interrupt the U-Boot and execute the following commands to re-create
    filesystem in the flash

    ffsmount c:/
    ffsfmt c:/

    this step takes a long time, about ~ 4 mins

8.  Execute the following commands to put the official images to the
    filesystem

    updatert <official image>

    example:

      updatert pn28160k_v30003.rom

    this step takes about ~ 40 secs

9.  Set the environment variables of the U-Boot by the following commands

    setenv loadaddr 0xb4e00000
    setenv bootcmd bootm
    saveenv

10: Download the OpenWrt initramfs image and boot with it

    tftpboot 0x81000000 0101A8C0.img
    bootm

11: On the initramfs image, download the sysupgrade image and perform
    sysupgrade with it

    sysupgrade <imagename>

12: Wait ~ 120 seconds to complete flashing

Known Issues:

- 2x SFP ports are provided as combo ports by the RTL8218FB chip, but the
  phy driver has no support for it. Currently, only TP ports work by the
  RTL8218D support.

Note:

- "Switch-M16eG" is a model name, and "PN28160K" is a model number.
  Switch-M16eG has an another (old) model number ("PN28160"), it's not a
  Realtek based hardware.

- Switch-M16eG has a "POWER" LED (Green), but it's not connected to any
  GPIO pin.

- U-Boot checks the runtime images in the flash when booting and fails
  to execute "bootcmd" variable if the images are not existing.

- A filesystem is formed in the flash (0x100000-0x1DFFFFF) on the stock
  firmware and it includes the stock images, configuration files and
  checksum files. It's unknown format, can't be managed on the OpenWrt.
  To get the enough space for OpenWrt, move the filesystem to the head
  of "fs_reserved" partition by execution of "ffsfmt" and "updatert".

- A GPIO pin on PCA9539 is used for resetting external RTL8218FB phy.
  This should be specified as "reset-gpios" property in MDIO node, but
  RTL8218FB won't be configured on RTL8218D support in the phy driver.
  So, ethernet ports on the phy will be broken after hard-resetting.
  At the moment, configure this pin as gpio-hog to avoid breaking by
  resetting.

Back to the stock firmware:

1. Delete "loadaddr" variable and set "bootcmd" to the original value

   on U-Boot:

     setenv loadaddr
     setenv bootcmd 'bootm 0x81000000'

   on OpenWrt:

     fw_setenv loadaddr
     fw_setenv bootcmd 'bootm 0x81000000'

2. Perform reset or reboot

  on U-Boot:

    reset

  on OpenWrt:

    reboot

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2022-08-06 14:39:57 +02:00
Hans Dedecker
a23d132cff odhcp6c: update to git HEAD
7d21e8d dhcpv6: add option to ignore stateless advertise

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
2022-08-05 18:31:24 +02:00
Christian Lamparter
d6801e0d3f kernel: silence refresh warning
|Warning: trailing whitespace in line 66 of drivers/mtd/parsers/Kconfig

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-08-05 14:10:42 +02:00
Daniel Kestrel
8756a04787 lantiq: fix lan port 3+4 phy-mode settings for Fritzbox 3390
There are forum reports that 2 LAN ports are still not working,
the phy-mode settings are adjusted to fix the problem.

Fixes: #10371
Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
2022-08-05 14:10:42 +02:00
Olliver Schinagl
943905b0b6 realtek: Fix typo in Kconfig prompt
As the symbol RTL930x shows, the bool enables the RTL930x platform, not
the RTL839x one.

Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
(slightly changed commit subject)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-08-05 14:10:42 +02:00
Chen Minqiang
31cca8f8d3 umdns: add missing syscall to seccomp filter
There is some syscall missing:
'getdents64'
'getrandom'
'statx'
'newfstatat'

Found with:
'mkdir /etc/umdns; ln -s /tmp/1.json /etc/umdns/; utrace /usr/sbin/umdns'

Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
2022-08-05 14:10:42 +02:00
Leo Soares
35a0f2b00c ath79: add LTE led for GL.iNet GL-XE300
This commit adds the LTE led for GL.iNet GL-XE300
to the default leds config.

Signed-off-by: Leo Soares <leo@hyper.ag>
2022-08-05 14:10:42 +02:00
Wenli Looi
4cccea02a6 ramips: fix fw_setsys
This change was included in the original pull request but later omitted
for some reason:

https://github.com/openwrt/openwrt/pull/4936

Signed-off-by: Wenli Looi <wlooi@ucalgary.ca>
2022-08-05 14:10:42 +02:00
Wenli Looi
0bfe1cfbb1 ramips: support fw_printenv for Netgear WAX202
Config partition contains uboot env for the first 0x20000 bytes.
The rest of the partition contains other data including the device MAC
address and the password printed on the label.

Signed-off-by: Wenli Looi <wlooi@ucalgary.ca>
2022-08-05 14:10:42 +02:00
Leo Soares
2b03f207e0 kernel: add kmod-usb-hid-mcp2221
"The MCP2221 is a USB-to-UART/I2C serial converter which enables
USB connectivity in applications that have a UART and I2C interfaces."
<https://www.microchip.com/en-us/product/MCP2221>

Signed-off-by: Leo Soares <leo@hyper.ag>
(replaced GPIOLIB KConfig with @GPIO_SUPPORT)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-08-05 14:10:42 +02:00
Christian Lamparter
3678881773 kernel: usb-serial-cp210x: @GPIO_SUPPORT
all other drivers depend on @GPIO_SUPPORT rather than
forcing CONFIG_GPIOLIB=y.

(I wonder what would happen if someone decides to try
UML with USBIP?)

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-08-05 14:10:42 +02:00
Paul Spooren
8019410f56 x86: add missing Lex 3I380NX network detection
The Lex 3I380NX industrial PC has 4 ethernet controllers on board
which need pmc_plt_clk0 - 3 to function, add it to the critclk_systems
DMI table, so that drivers/clk/x86/clk-pmc-atom.c will mark the clocks
as CLK_CRITICAL and they will not get turned off.

This commit is nearly redundant to 3d0818f5eba8 ("platform/x86:
pmc_atom: Add Lex 3I380D industrial PC to critclk_systems DMI table")
but for all Lex Baytrail devices.

The original vendor firmware is only available using the WaybackMachine:
http://www.lex.com.tw/products/3I380NX.html

Signed-off-by: Michael Schöne <michael.schoene@rhebo.com>
Signed-off-by: Paul Spooren <paul.spooren@rhebo.com>
(Hans broader version for more Lex Baytrail systems, v5.15)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-08-05 14:10:11 +02:00
Roland Barenbrug
456b9029d7 ltq-vdsl-app: Fix counter overflow resulting in negative values
The re-transmit counters can overflow the 32 bit representation resulting
in negative values being displayed. Background being that the numbers are
treated at some point as signed INT rather than unsigned INT.
Change the counters from 32 bit to 64 bit, should provide sufficient room
to avoid any overflow. Not the nicest solution but it works

Fixes: #10077
Signed-off-by: Roland Barenbrug <roland@treslong.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
2022-08-05 13:49:30 +02:00
Mark Mentovai
beeb49740b libmnl: fix build when bash is not located at /bin/bash
This fixes the libmnl build on macOS, which ships with an outdated bash
at /bin/bash. During the OpenWrt build, a modern host bash is built and
made available at staging_dir/host/bin/bash, which is present before
/bin/bash in the build's PATH.

This is similar to 8f7ce3aa6d, presently appearing at
package/kernel/mac80211/patches/build/001-fix_build.patch.

Signed-off-by: Mark Mentovai <mark@mentovai.com>
2022-07-31 20:30:20 +02:00
Shiji Yang
1330816178 ramips: add support for H3C TX1800 Plus / TX1801 Plus / TX1806
H3C TX180x series WiFi6 routers are customized by different carrier.
While these three devices look different, they use the same motherboard
inside. Another minor difference comes from the model name definition
in the u-boot environment variable.

Specifications:
 SOC:      MT7621 + MT7915
 ROM:      128 MiB
 RAM:      256 MiB
 LED:      status *2
 Button:   reset *1 + wps/mesh *1
 Ethernet:        lan *3 + wan *1 (10/100/1000Mbps)
 TTL Baudrate:    115200
 TFTP server IP:  192.168.124.99

MAC Address:
 use        address(sample 1)   address(sample 2)    source
 label      88:xx:xx:98:xx:12   88:xx:xx:a2:xx:a5   u-boot-env@ethaddr
 lan        88:xx:xx:98:xx:13   88:xx:xx:a2:xx:a6   $label +1
 wan        88:xx:xx:98:xx:12   88:xx:xx:a2:xx:a5   $label
 WiFi4_2G   8a:xx:xx:58:xx:14   8a:xx:xx:52:xx:a7   (Compatibility mode)
 WiFi5_5G   8a:xx:xx:b8:xx:14   8a:xx:xx:b2:xx:a7   (Compatibility mode)
 WiFi6_2G   8a:xx:xx:18:xx:14   8a:xx:xx:12:xx:a7
 WiFi6_5G   8a:xx:xx:78:xx:14   8a:xx:xx:72:xx:a7

Compatibility mode is used to guarantee the connection of old devices
that only support WiFi4 or WiFi5.

TFTP + TTL Installation:
Although a TTL connection is required for installation, we do not need
to tear down it. We can find the TTL port from the cooling hole at the
bottom. It is located below LAN3 and the pins are defined as follows:
|LAN1|LAN2|LAN3|----|WAN|
--------------------
    |GND|TX|RX|VCC|

1. Set tftp server IP to 192.168.124.99 and put initramfs firmware in
   server's root directory, rename it to a simple name "initramfs.bin".
2. Plug in the power supply and wait for power on, connect the TTL cable
   and open a TTL session, enter "reboot", then enter "Y" to confirm.
   Finally push "0" to interruput boot while booting.
3. Execute command to install a initramfs system:
   # tftp 0x80010000 192.168.124.99:initramfs.bin
   # bootm 0x80010000
4. Backup nand flash by OpenWrt LuCI or dd instruction. We need those
   partitions if we want to back to stock firmwre due to official
   website does not provide download link.
   # dd if=/dev/mtd1 of=/tmp/u-boot-env.bin
   # dd if=/dev/mtd4 of=/tmp/firmware.bin
5. Edit u-boot env to ensure use default bootargs and first image slot:
   # fw_setenv bootargs
   # fw_setenv bootflag 0
6. Upgrade sysupgrade firmware.
7. About restore stock firmware: flash the "firmware" and "u-boot-env"
   partitions that we backed up in step 4.
   # mtd write /tmp/u-boot-env.bin u-boot-env
   # mtd write /tmp/firmware.bin firmware

Additional Info:
The H3C stock firmware has a 160-byte firmware header that appears to
use a non-standard CRC32 verification algorithm. For this part of the
data, the u-boot does not check it so we can just directly replace it
with a placeholder.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2022-07-31 19:23:24 +02:00
John Audia
364575e3a3 kernel: bump 5.15 to 5.15.58
All patches automatically rebased.

Build system: x86_64
Build-tested: bcm2711/RPi4B, mt7622/RT3200
Run-tested: bcm2711/RPi4B, mt7622/RT3200

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-07-31 18:55:22 +02:00
John Audia
9d2ffe8cb8 x86: update defconfig for 5.15.57
Add some new/missing symbols relating to speculative execution mitigations[1].

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/diff/arch/x86/Kconfig?id=v5.15.57&id2=v5.15.56

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-07-31 18:55:22 +02:00
John Audia
317f59a0ee kernel: bump 5.15 to 5.15.57
All patches automatically rebased.

Build system: x86_64
Build-tested: bcm2711/RPi4B, mt7622/RT3200
Run-tested: bcm2711/RPi4B, mt7622/RT3200

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-07-31 18:55:22 +02:00
John Audia
4921ab0be4 kernel: bump 5.15 to 5.15.56
Manually rebased:
  bcm27xx/patches-5.15/950-0470-sound-usb-add-device-quirks-for-A4Tech-FHD-1080p-web.patch

Remove upstreamed:
  bcm27xx/patches-5.15/950-0060-tty-amba-pl011-Add-un-throttle-support.patch[1]

All other patches automatically rebased.

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.56&id=2db3b95166f72e6481a79b82b1d6f94f4b18fcc1

Build system: x86_64
Build-tested: bcm2711/RPi4B, mt7622/RT3200
Run-tested: bcm2711/RPi4B, mt7622/RT3200

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-07-31 18:55:22 +02:00
John Audia
ce014b1e39 kernel: bump 5.15 to 5.15.55
All patches automatically rebased.

Build system: x86_64
Build-tested: bcm2711/RPi4B, mt7622/RT3200
Run-tested: bcm2711/RPi4B, mt7622/RT3200

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-07-31 18:55:22 +02:00
John Audia
e4af991220 kernel: bump 5.15 to 5.15.54
All patches automatically rebased.

Build system: x86_64
Build-tested: bcm2711/RPi4B, mt7622/RT3200
Run-tested: bcm2711/RPi4B, mt7622/RT3200

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-07-31 18:55:22 +02:00
Andre Heider
81bc733c33 arm-trusted-firmware-mvebu: update cm3 gcc to 11.2
https://developer.arm.com/tools-and-software/open-source-software/developer-tools/gnu-toolchain/downloads

Signed-off-by: Andre Heider <a.heider@gmail.com>
2022-07-31 18:53:24 +02:00
Andre Heider
794cefd3e3 arm-trusted-firmware-mvebu: update to v2.7
Remove the backported patches and add another to allow building with the
OpenWrt build system.

Signed-off-by: Andre Heider <a.heider@gmail.com>
2022-07-31 18:53:24 +02:00