Commit Graph

3710 Commits

Author SHA1 Message Date
Szabolcs Hubai
d41b8a570f ramips: mt7621: use lzma-loader for Sercomm NA502
This fixes a well known "LZMA ERROR 1" error on Sercomm NA502,
reported on the OpenWrt forum. [1]

[1]: https://forum.openwrt.org/t/176942

Signed-off-by: Szabolcs Hubai <szab.hu@gmail.com>
2023-11-12 15:32:24 +01:00
Alan Luck
4c0dc68f46 ramips: add encrypted SGE factory image for D-Link devices
creates SGE encrypted factory images
to use via the D-Link web interface
rename the old factory unencrypted images to recovery
for use in the recovery console when recovery is needed
DIR-1935-A1 , DIR-853-A1 , DIR-853-A3 , DIR-867-A1 ,
DIR-878-A1 and DIR-882-A1

Signed-off-by: Alan Luck <luckyhome2008@gmail.com>
2023-11-12 15:03:05 +01:00
Filip Milivojevic
168beef1dd
ramips: Cudy WR1300v2 fix mt7613 calibration data length
Since MT7613 is handled by MT7615 driver, and other devices using MT7615
have reg = <0x8000 0x4da8>; this needs updating or eeprom data fails to load.

Signed-off-by: Filip Milivojevic <zekica@gmail.com>
2023-11-08 17:16:18 +01:00
Mikhail Zhilkin
45a50a06fb treewide: fix MERCUSYS brand spelling
This commit fixes MERCUSYS brand spelling. The proper name is capitalized.

Link: https://www.mercusys.com/
Link: https://github.com/torvalds/linux/blob/master/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_core.c#L7779

Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
2023-11-03 23:06:07 +01:00
Daniel Golle
bc335f2967 ramips: add support for MeiG SLT866 4G CPE
Hardware:
 - SoC: Mediatek MT7621 (MT7621AT)
 - Flash: 32 MiB SPI-NOR (Macronix MX25L25635E)
 - RAM: 128 MiB
 - Ethernet: Built-in, 2 x 1GbE
 - 3G/4G Modem: MEIG SLM828 (currently only supported with ModemManager)
 - SLIC: Si32185 (unsupported)
 - Power: 12V via barrel connector
 - Wifi 2.4GHz: Mediatek MT7603BE 802.11b/g/b
 - Wifi 5GHz: Mediatek MT7613BE 802.11ac/n/a
 - LEDs: 8x (7 controllable)
 - Buttons: 2x (RESET, WPS)

Installing OpenWrt:
 - sysupgrade image is compatible with vendor firmware.

Recovery:
 - Connect to any of the Ethernet ports, configure local IP:
   10.10.10.3/24 (or 192.168.10.19/24, depending on OEM)
 - Provide firmware file named 'mt7621.img' on TFTP server.
 - Hold down both, RESET and WPS, then power on the board.
 - Watch network traffic using tcpdump or wireshark in realtime to
   observe progress of device requesting firmware. Once download has
   completed, release both buttons and wait until firmware comes up.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-11-03 21:16:29 +00:00
Mikhail Zhilkin
1cb85e1251
ramips: fix wrong permissions on dts files
This commit fixes wrong permissions on dts files. Before the commit these
dts files are executable:
   -rwxrwxr-x mt7620a_dlink_dir-806a-b1.dts
   -rwxrwxr-x mt7621_wavlink_wl-wn573hx1.dts

Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
2023-11-02 20:42:53 +01:00
Mikhail Zhilkin
7666940efe ramips: enable wireless LEDs activity blinking for TP-Link EC330-G5u v1
This commit enables wireless LEDs activity blinking for TP-Link EC330-G5u
v1 router.

Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
2023-10-31 13:56:58 +01:00
Shiji Yang
f025135f16 ramips: fix Gigabit Ethernet port of the HiWiFi HC5861
HiWiFi HC5861 has a GbE port which connected to the RTL8211E PHY
chip. This patch adds the missing Realtek PHY driver package and
sets the correct external PHYs base address to make it work again.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2023-10-29 22:49:35 +01:00
Milan Krstic
17465fc77e ramips: add support for ZyXEL LTE5398-M904
ZyXEL LTE5398-M904 is a dual band 802.11ac indoor LTE/3G CPE with an FXS
port.

Specifications:

* SoC: Mediatek MT7621AT
* RAM: 256 MB
* Flash: 128MB NAND (MX30LF1G18AC)
* WiFi: MediaTek MT7603 2.4G + MediaTek MT7615 5G
* Switch: 2 GbE ports MT7530
* LTE/3G: Quectel EG18-EA LTE-A Cat. 18
* SIM: 1 micro-SIM card slot
* Buttons: Reset, WPS
* LEDs: power (G/B), internet (G), LTE (R/G/Orange), WiFi (G), voice (G)
* VoIP: 1 FXS RJ11 port
* Power: 12V, 2A

UART serial console:

57600,8N1
Unpopulated header J5:

 [o] GND
 [ ] key - no pin
 [o] RX
 [o] TX
 [o] 3.3V Vcc

Installation:

* Log in as root using ssh to 192.168.1.1
* scp OpenWrt initramfs-recovery.bin image to root@192.168.1.1:/tmp/
* Prepare bootloader config by running:
   nvram setro uboot DebugFlag 0x1
   nvram setro uboot CheckBypass 0
   nvram commit
* Run "mtd_write -w write /tmp/initramfs-recovery.bin Kernel" and reboot
* Wait for OpenWrt to boot and ssh to root@192.168.1.1
* Run sysupgrade with OpenWrt squashfs-sysupgrade.bin image

For mode details about flashing see:
2449a63208 (ramips: mt7621: Add support for ZyXEL NR7101, 2021-04-19)

Unsupported:

* FXS/Voice

Signed-off-by: Milan Krstic <milan.krstic@gmail.com>
2023-10-29 18:51:11 +01:00
Rani Hod
fe5e498777 ramips: TP-link archer A6/C6 device tree updates
Set correct GPIO (10) for the WPS button. This matches GPIO settings in
vendor GPL sources. Note that GPL sources also mention a USB indicator
LED (GPIO 13) but the device has neither an external USB port nor a USB LED.

In addition, prefixes (button-, led-) are added to relevant DT entries,
as well as color and function specifications for LEDs.

Closes: #13736

Reported-by: Waldemar Czabaj <kaball@wp.pl>
Signed-off-by: Rani Hod <rani.hod@gmail.com>
(added led mitigations for wifi leds)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2023-10-22 11:11:43 +02:00
Shiji Yang
6f31941d38 Revert "ramips: convert MT7915 EEPROM to NVMEM format"
Some MT7915 devices need to load the second part of the eeprom to
work properly. The mt76 driver is not yet ready to read the pre-cal
data via the NVMEM cell. Therefore, partially revert commit to fix
the device probe issue on some devices.

P.S.
Except for D-Link and Ubnt devices, It is still uncertain whether
pre-cal data is required for other devices in the patch.

This partially reverts commit 9ac891f8c4.

Fixes: https://github.com/openwrt/openwrt/issues/13700
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2023-10-17 20:57:07 +08:00
Shiji Yang
9921973ca4
ramips: add missing mt76 packages for Telco Electronics X1
Telco Electronics X1 has MT7603E and MT7612E PCIe NICs. They are
driven by kmod-mt7603 and kmod-mt76x2.

Ref: 73e0f52b6e ("ramips: add support for Telco Electronics X1")
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2023-10-17 12:07:28 +02:00
Shiji Yang
366ffa53bd
ramips: fix factory partition size for SNR-CPE-W4N
The starting address of 'factory' partition is 0x40000, and the
starting address of the next partition is 0x50000. It's obvious
that the correct size for the 'factory' is 0x10000, just like
other MT7620 devices.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2023-10-17 12:07:28 +02:00
Shiji Yang
b5d059d677
ramips: fix frequency limit property for some Edimax devices
These three devices uses MT7612E PCIe NIC and supported by the
'mt76' driver. So the right frequency limit property should be
`ieee80211-freq-limit`.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2023-10-17 12:07:27 +02:00
Shiji Yang
95e241d2af
ramips: remove useless status property from wmac dts node
On the ramips target, all 'wmac' nodes in SoC dtsi are enabled by
default except mt7628. There is no need to mark them as 'okay'
again. So these useless properties can be removed.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2023-10-17 12:07:27 +02:00
Shiji Yang
f53fa2a0cb
ramips: convert mt76 PCIe NIC EEPROM to NVMEM format for legacy SoCs
This patch converts MT761{0,2,3} PCIe WiFi calibration data to NVMEM
format for legacy Ralink SoCs (MT7620 and Mt7628). The EEPROM size of
the MT7610 and MT7612 is 0x200. there are only three devices uses
MT7613 NIC, ASUS RT-AC1200 V2, COMFAST CF-WR758AC V2 and Keenetic
KN-1613. The EEPROM size of them is 0x4da8.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2023-10-17 12:07:27 +02:00
Shiji Yang
e93f41adee
ramips: convert MT7628 EEPROM to NVMEM format
This patch converts MT7628 WiFi calibration data to NVMEM format. The
EEPROM size is 0x400.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2023-10-17 12:07:26 +02:00
Shiji Yang
da42c329c6
ramips: convert rt2x00 EEPROM to NVMEM format
This patch converts legacy Ralink SoCs and MT7620 WiFi calibration
data to NVMEM format. The EEPROM size is 0x200.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2023-10-17 12:07:26 +02:00
Shiji Yang
f35ddef268
ramips: fix mtd partition node names for Phicomm PSG1208
The mtd partition node name should be "partition@${offset}".
However, the offsets of the PSG1208 don't match the partition
'reg' properties. This patch correct the wrong offsets.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2023-10-17 12:07:26 +02:00
Shiji Yang
7668fc8112
ramips: fix DTS EEPROM property for some MT7628 devices
The MT7628 integrated wireless is driven by `mt76`, so the right
EEPROM property name is `mediatek,mtd-eeprom`.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2023-10-17 12:07:26 +02:00
Shiji Yang
58502650e1
ramips: convert the remaining mtd-mac-address to NVMEM format
`mtd-mac-address` has been abandoned. Therefore, convert them to
NVMEM format. This patch also removes some useless mtd-mac-address
properties.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2023-10-17 12:07:22 +02:00
Bjørn Mork
2e57028424
ramips: fix ZyXEL NR7101 bricking typo
A typo snuck in with the addition of Cudy M1800, changing
"nr7101" to "nt7101". The result is a default network config
for NR7101 without the only ethernet interface on the NR7101,
thereby soft bricking it.

Fixes: f6d394e9f2 ("ramips: add support for Cudy M1800")
Signed-off-by: Bjørn Mork <bjorn@mork.no>
2023-10-15 19:28:59 +02:00
Shiji Yang
9ac891f8c4
ramips: convert MT7915 EEPROM to NVMEM format
This patch converts MT7915 WiFi calibration data to NVMEM format. The
EEPROM size is 0xe00.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2023-10-09 11:15:52 +02:00
Shiji Yang
65cd6a6fec
ramips: convert MT7613 and MT7615 EEPROM to NVMEM format for MT7621
This patch converts MT7613 and MT7615 WiFi calibration data to NVMEM
format. The EEPROM size is 0x4da8.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2023-10-09 11:15:52 +02:00
Shiji Yang
2c02a9b9e4
ramips: convert MT7610 and MT7612 EEPROM to NVMEM format for MT7621
This patch converts MT7610 and MT7612 WiFi calibration data to NVMEM
format. The EEPROM size is 0x200.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2023-10-09 11:15:52 +02:00
Shiji Yang
fb4cea45ec
ramips: convert MT7603 EEPROM to NVMEM format
This patch converts MT7603 WiFi calibration data to NVMEM format. The
EEPROM size is 0x400.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2023-10-09 11:15:52 +02:00
Shiji Yang
230d5de707
ramips: correct NVMEM MAC address node name and label for Bolt Arion
The node name&label should match the address in the 'reg' property,
so it's better to change the incorrect offset to the 0x28.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2023-10-09 11:15:51 +02:00
Shiji Yang
22b0c36ae7
ramips: fix EEPROM size for I-O DATA WN-DEAX1800GR
I-O DATA WN-DEAX1800GR uses MT7915 PCIe NIC. The correct EEPROM
size is 0xe00.

Fixes: ac68fbf526 ("ramips: add support for I-O DATA WN-DEAX1800GR")
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2023-10-09 11:15:51 +02:00
Alexey D. Filimonov
ff95f859eb ramips: cf-ew72-v2: Add support for COMFAST CF-EW72 V2
Add support for COMFAST CF-EW72 V2

Hardware:
-   SoC: Mediatek MT7621 (MT7621DAT or MT7621AT)
-   Flash: 16 MiB NOR
-   RAM: 128 MiB
-   Ethernet: Built-in, 2 x 1GbE
-   Power: only 802.3af PD on any port, injector supplied in the box
-   PoE passthrough: No
-   Wifi 2.4GHz: Mediatek MT7603BE 802.11b/g/b
-   Wifi 5GHz: Mediatek MT7613BEN 802.11ac/n/a
-   LEDs: 8x (only 1 is both visible and controllable, see below)
-   Buttons: 1x (RESET)

Installing OpenWrt:
Flashing is done using Mediatek U-Boot System Recovery Mode
-   make wired connection with 2 cables like this:
-     -   PC (LAN) <-> PoE Injector (LAN)
-     -   PoE Injector (POE) <-> CF-EW72 V2 (LAN). Leave unconnected to CF-EW72 V2 yet.
-   configure 192.168.1.(2-254)/24 static ip address on your PC LAN
-   press and keep pressed RESET button on device
-   power the device by plugging PoE Injector (POE) <-> CF-EW72 V2 (LAN) cable
-   wait for about 10 seconds until wifi led stops blinking and release RESET button
-   navigate from your PC to http://192.168.1.1 and upload OpenWrt *-factory.bin firmware file
-   proceed until router starts blinking with wifi led again (flashing) and stops (rebooting to OpenWrt)

MAC addresses as verified by OEM firmware:
  vendor OpenWrt  address
  LAN    lan\eth0 label
  WAN    wan     label + 1
  2g     phy0    label + 2
  5g     phy1    label + 3

  The label MAC address was found in 0xe000.

LEDs detailed:
  The only both visible and controllable indicator is blue:wlan LED.
  It is not bound by default to indicate activity of any wireless interfaces.

  Place (WAN->ANT) | Num | GPIO | LED name (LuCI)   | Note
  -----------------|-----|-----------------------------------------------------------------------------------------
             power | 1   |      |                   | POWER LED. Not controlled with GPIO.
      hidden_led_2 | 2   | 13   | blue:hidden_led_2 | This LED does not have proper hole in shell.
               wan | 3   |      |                   | WAN LED. Not controlled with GPIO.
      hidden_led_4 | 4   | 16   | blue:hidden_led_4 | This LED does not have proper hole in shell.
               lan | 5   |      |                   | LAN LED. Not controlled with GPIO.
      noconn_led_6 | 6   |      |                   | Not controlled with GPIO, possibly not connected
              wlan | 7   | 15   | blue:wlan         | WLAN LED. Wireless indicator.
      noconn_led_8 | 8   |      |                   | Not controlled with GPIO, possibly not connected

  mt76-phy0 and mt76-phy1 leds also exist in OpenWrt, but do not exist on board.

Signed-off-by: Alexey D. Filimonov <alexey@filimonic.net>
2023-09-27 00:10:16 +02:00
Andreas Böhler
191da23551 ramips: fix Mercusys MR70X LAN port assignments
A bug report in the forum found that the MR70X lists four LAN ports in LuCI
while it has only three. This adds the device to the network setup file
to fix the issue.

Identified-by: Forum User "Lexeyko"
Signed-off-by: Andreas Böhler <dev@aboehler.at>
2023-09-24 17:09:26 +02:00
Sijia Huang
ab12a01cd7 ramips: add support for WAVLINK WL-WN573HX1
Hardware
--------

Specifications:
- Device: WAVLINK WL-WN573HX1 Outdoor AP
- SoC: MT7621AT
- Flash: 16MB
- RAM: 256MB
- Switch:1 LAN (10/100/1000 Mbps)
- WiFi: MT7905 2x2 2.4G + MT7975 2x2 5G
- LEDs: 1x STATUS (blue, configurable)
		1x LAN (green)

Product link:
https://www.wavlink.com/en_us/product/WL-WN573HX1.html

Signed-off-by: Sijia Huang <engineer31@win-star.com>
2023-09-24 12:36:52 +02:00
John Audia
ac422c9788
kernel: bump 5.15 to 5.15.132
Changelog: https://cdn.kernel.org/pub/linux/kernel/v5.x/ChangeLog-5.15.132

Removed upstreamed:
	bcm53xx/patches-5.15/037-v6.6-0006-ARM-dts-BCM53573-Add-cells-sizes-to-PCIe-node.patch[1]
	bcm53xx/patches-5.15/037-v6.6-0007-ARM-dts-BCM53573-Use-updated-spi-gpio-binding-proper.patch[2]
	bcm53xx/patches-5.15/037-v6.6-0008-ARM-dts-BCM5301X-Extend-RAM-to-full-256MB-for-Linksy.patch[3]

All other patches automatically rebased.

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.132&id=b35f3ca1877e024887df205ede952863d65dad36
2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.132&id=2840d9b9c8750be270fb1153ccd5b983cbb5d592
3. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.132&id=f086e859ddc252c32f0438edff241859c0f022ce

Build system: x86_64
Build-tested: ramips/tplink_archer-a6-v3
Run-tested: ramips/tplink_archer-a6-v3

Signed-off-by: John Audia <therealgraysky@proton.me>
2023-09-20 14:13:00 +02:00
Max Qian
794349a28a ramips: RT1800: fix invalid octal number error
This commit removes the padded zeros in the date formatting.
The padded zeros from the date command causes the numbers
to be interpreted as an octal number by printf. Months, days,
and years with the number 08 or 09 raise an error in printf as an
"invalid octal number" and get interpreted as a zero.

Signed-off-by: Max Qian <public@maxqia.com>
2023-09-17 13:52:55 -07:00
Aviana Cruz
46d673033b
ramips: add support for mtk eip93 crypto engine
Mediatek EIP93 Crypto engine is a crypto accelerator which
is available in the Mediatek MT7621 SoC.

Signed-off-by: Aviana Cruz <gwencroft@proton.me>
Co-authored-by: Richard van Schagen <vschagen@icloud.com>
Co-authored-by: Chukun Pan <amadeus@jmu.edu.cn>
2023-09-12 14:57:54 +02:00
Daniel Golle
3b86c1f929 kernel: backport two fixes for MediaTek Ethernet driver
Fix PSE port assignment for 3rd GMAC on MT7988 and make sure dma_addr
is always initialized to prevent potentially accessing uninitialized
stack memory in the error path.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-09-11 14:09:48 +01:00
Piotr Dymacz
f1aaa267f0 ramips: add support for ALFA Network AX1800RM
ALFA Network AX1800RM (FCC ID: 2AB877621) is a dual-band Wi-Fi 6
(AX1800) router, based on MediaTek MT7621A + MT79x5D platform.

Specifications:

- SOC:      MT7621A (880 MHz)
- DRAM:     DDR3 256 MiB (Nanya NT5CC128M16JR-EK)
- Flash:    16 MiB SPI NOR (EN25QH128A-104HIP)
- Ethernet: 4x 10/100/1000 Mbps (SOC's built-in switch)
- Wi-Fi:    2x2:2 2.4/5 GHz (MT7905DAN + MT7975DN)
            (MT7905DAN doesn't support background DFS scan/BT)
- LED:      6x green, 1x green/red
- Buttons:  2x (reset, WPS)
- Antenna:  4x external, non-detachable omnidirectional
- UART:     1x 4-pin (2.54 mm pitch, J4, not populated)
- Power:    12 V DC/1 A (DC jack)

MAC addresses:

LAN:     00:c0:ca:xx:xx:4e (factory 0x4, +2)
WAN:     00:c0:ca:xx:xx:4f (factory 0x4, +3)
2.4 GHz: 00:c0:ca:xx:xx:4c (factory 0x4, device's label)
5 GHz:   00:c0:ca:xx:xx:4c (factory 0xa)

Flash instructions for web-based U-Boot recovery:

1. Power the device with WPS button pressed and wait around 10 seconds.
2. Setup static IP 192.168.1.2/24 on your PC.
3. Go to 192.168.1.1 in browser and upload 'recovery' image.

The device runs LEDE 17.01 (kernel 4.4.x) based firmware with 'failsafe'
mode available which allows alternative upgrade method:

1. Run device in 'failsafe' mode and change password for default user.
2. SSH to the device, transfer 'sysupgrade' image and perform upgrade
   in forced mode, without preserving settings: 'sysupgrade -n -F ...'.

Other notes:

If you own early version of this device, the vendor firmware might
refuse OpenWrt image because of missing custom header. In that case,
ask vendor's customer support for stock firmware without custom header
support/requirement.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2023-09-11 11:41:57 +02:00
John Audia
58bb5e147a kernel: bump 5.15 to 5.15.131
Changelog: https://cdn.kernel.org/pub/linux/kernel/v5.x/ChangeLog-5.15.131

All patches automatically rebased.

Build system: x86_64
Build-tested: ramips/tplink_archer-a6-v3
Run-tested: ramips/tplink_archer-a6-v3

Signed-off-by: John Audia <therealgraysky@proton.me>
2023-09-08 21:24:48 +02:00
Daniel Golle
f631c7bbb1 generic: sync MediaTek Ethernet driver with upstream
Import commits from upstream Linux replacing some downstream patches.
Move accepted patches from pending-{5.15,6.1} to backport-{5.15,6.1}.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-08-28 16:35:22 +01:00
Rani Hod
a4eb1ea331 ramips: add support for D-Link DRA-1360
The DRA-1360 rev A is a wall-plug AC1300 repeater.
Hardware is identical (same FCC ID, black case instead of white)
to D-Link DAP-1620 rev B, which is already supported, but a
different model name, revision, and hardware ID are needed.
Thus, the bulk of the DAP-1620 device tree is extracted to a
common dtsi included by the two models' device trees.

Repeating specs and installation instructions from e4c7703:
(note that the RAM size mentioned there was incorrect, oops)

Specs:
- SoC: MT7621AT (880MHz dual-core MIPS1004Kc)
- Memory: 128 MiB RAM, 16 MiB NOR SPI
- WiFi: MT7615DN 2x2 802.11n + 2x2 802.11ac (DBDC)
- Ethernet: 1 RJ45 port 10/100/1000
- Power/status LED: red+green
- LED RSSI bargraph: 2x green, 1x red+green

Installation:
- Keep reset button pressed during plug-in
- Web Recovery Updater is at 192.168.0.50
  (pings are ignored, it listens only for http)
- Upload factory.bin, confirm flashing
  (seems to work best with Chromium-based browsers)

Revert to OEM firmware:
- tail -c+117 DRA1360A1_FW112B03.bin | \
  openssl aes-256-cbc -d -md md5 -out decrypted.bin \
  -k c471706398cb147c6619f8a04a18d53e9c17ede8
- flash decrypted.bin via D-Link Web Recovery

Signed-off-by: Rani Hod <rani.hod@gmail.com>
2023-08-27 19:13:36 +02:00
INAGAKI Hiroshi
ac68fbf526 ramips: add support for I-O DATA WN-DEAX1800GR
I-O DATA WN-DEAX1800GR is a 2.4/5 GHz band 11ax (Wi-Fi 6) router, based
on MT7621A.

Specification:

- SoC         : MediaTek MT7621A
- RAM         : DDR3 256 MiB (Nanya NT5CC128M16JR-EK)
- Flash       : RAW NAND 128 MiB (Winbond W29N01HVSINF)
- WLAN        : 2.4/5 GHz (MediaTek MT7915)
- Ethernet    : 5x 10/100/1000 Mbps
  - Switch    : MT7530 (SoC)
- LEDs/Keys   : 6x/3x
- UART        : through-hole on PCB (J2)
  - assignment: 3.3V, GND, TX, RX from "1" marking
  - settings  : 115200n8
- Power       : 12 VDC, 1 A

Flash instruction using initramfs-factory image:

1. Boot WN-DEAX1800GR normally
2. Access to "http://192.168.0.1/" and open firmware update page
   ("ファームウェア")
3. Select the OpenWrt initramfs-factory.bin image and click update
   ("更新") button to perform firmware update
4. On the initramfs image, perform sysupgrade with the
   squashfs-sysupgrade.bin image
5. Wait ~120 seconds to complete flashing

Note:

- This device has 2x OS images on the flash storage. In this support,
  the first one will be used.

Warning:

- Do not use "saveenv" command on U-Boot CLI.
  This device has wrong u-boot-env data. The actual length of individual
  env data installed to the device is 0x1000 (4 KiB), but installed
  U-Boot requires 0x20000 (128 KiB). So U-Boot determines the data is
  invalid. Then, if you perform saving environment data with saveenv on
  U-Boot CLI, installed env data will be overwritten with too few
  default values without individual values (SSID, password, MAC
  addresses, etc...).

MAC addresses:

LAN    : 50:41:B9:xx:xx:F4 (Config, ethaddr (text))
WAN    : 50:41:B9:xx:xx:F6 (Config, wanaddr (text))
2.4 GHz: 50:41:B9:xx:xx:F4 (Config, rmac (text) / Factory, 0x4 (hex))
5 GHz  : 50:41:B9:xx:xx:F5 (none)

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2023-08-20 01:26:15 +02:00
INAGAKI Hiroshi
9088b5445f ramips: improve sysupgrade helpers for I-O DATA devices
I-O DATA devices manufactured by MSTC (MitraStar Technology Corp.)
have some important flags for booting, "bootnum" and "debugflag".
The almost devices have both flags but some devices have only
"bootnum" flag.
So optimize helper functions in iodata.sh to set each flags.

- both:
  - WN-AX1167GR2
  - WN-AX2033GR
  - WN-DX1167R
  - WN-DX1200GR
  - WN-DX2033GR

- "bootnum" only
  - WN-DEAX1800GR

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2023-08-20 01:26:15 +02:00
Ivan Pavlov
54e5e396c5 ramips: improve Xiaomi mi-mini indications
Sets status indications led color on Xiaomi mi-mini router as other Xiaomi routers

Signed-off-by: Ivan Pavlov <AuthorReflex@gmail.com>
2023-08-14 20:08:05 +02:00
John Audia
daed3322d3 kernel: bump 5.15 to 5.15.125
1. Add new symbols to generic config
2. Bump kernel
   Changelog: https://lore.kernel.org/stable/2023080818-groin-gradient-a031@gregkh/

   All patches automatically rebased.

Signed-off-by: John Audia <therealgraysky@proton.me>
2023-08-09 22:06:24 +02:00
John Audia
81c1172c36 kernel: bump 5.15 to 5.15.124
Changelog: https://lore.kernel.org/stable/2023080341-curliness-salary-4158@gregkh/

1. Needed to make a change to to package/kernel/linux/modules/netsupport.mk
   due to upstream moving vxlan to its own directory[1].  @john-tho suggested
   using the the 6.1 xvlan FILES to circumvent.
2. All patches automatically rebased.

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.124&id=77396fa9096abdbfbb87d63e73ad44d5621cf103

Signed-off-by: John Audia <therealgraysky@proton.me>
2023-08-09 22:06:23 +02:00
John Audia
8590531048 kernel: bump 5.15 to 5.15.123
Manually rebased:
	bcm4908/patches-5.15/071-v6.1-0001-net-broadcom-bcm4908_enet-handle-EPROBE_DEFER-when-g.patch
	bcm53xx/patches-5.15/180-usb-xhci-add-support-for-performing-fake-doorbell.patch
	ipq40xx/patches-5.15/902-dts-ipq4019-ap-dk04.1.patch[*]

Removed upstreamed:
	backport-5.15/735-v6.5-net-bgmac-postpone-turning-IRQs-off-to-avoid-SoC-han.patch[1]
	backport-5.15/817-v6.5-01-leds-trigger-netdev-Recheck-NETDEV_LED_MODE_LINKUP-o.patch[2]
	pending-5.15/143-jffs2-reduce-stack-usage-in-jffs2_build_xattr_subsys.patch[3]
	pending-5.15/160-workqueue-fix-enum-type-for-gcc-13.patch[4]
	bcm53xx/patches-5.15/036-v6.5-0003-ARM-dts-BCM5301X-Drop-clock-names-from-the-SPI-node.patch[5]
	bcm53xx/patches-5.15/036-v6.5-0015-ARM-dts-BCM5301X-fix-duplex-full-full-duplex.patch[6]

All other patches automatically rebased.

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.123&id=02474292a44205c1eb5a03634ead155a3c9134f4
2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.123&id=86b93cbfe104e99fd3d25a49748b99fb88101573
3. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.123&id=79b9ab357b6f5675007f4c02ff8765cbd8dc06a2
4. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.123&id=d528faa9e828b9fc46dfb684a2a9fd8c2e860ed8
5. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.123&id=5899bc4058e89d5110a23797ff94439c53b77c25
6. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.123&id=95afd2c7c7d26087730dc938709e025a303e5499

Build system: x86/64
Build-tested: ramips/tplink_archer-a6-v3
Run-tested: ramips/tplink_archer-a6-v3

Co-authored-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John Audia <therealgraysky@proton.me>
[rebased ipq40xx/patches-5.15/902-dts-ipq4019-ap-dk04.1.patch ]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2023-07-30 18:02:47 +02:00
Shiji Yang
96010bb17c ramips: mt7621-wdt: use phandle to access system controller registers
These patches allow the driver to access some watchdog registers via a
phandle to the system controller node[1]. To apply these changes, we
need to add "mediatek,sysctl" to the SoC dtsi. This commit also remove
the redundent clocks, interrupts and resets properties.

[1] https://lore.kernel.org/all/20230214103936.1061078-2-sergio.paracuellos@gmail.com

Tested on Motorola MWR03 (MT7628)

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2023-07-30 13:09:23 +02:00
Shiji Yang
1f818b09f8 ramips: add proper system clock and reset driver support for legacy SoCs
This series of upstream patches properly implement a clock and reset
driver for old ralink SoCs[1]. And it includes some related fixes[2] and
improvements[3][4]. All patches have been merged into linux-next. They
will be part of upcoming Linux 6.5. In order to switch to the new system
controller driver, all clocks and resets properties in SoC dtsi have been
updated, and kernel symbol "CONFIG_CLK_MTMIPS" have been added to the
kernel config files.

[1] https://lore.kernel.org/all/20230619040941.1340372-1-sergio.paracuellos@gmail.com
[2] https://lore.kernel.org/all/20230622-mips-ralink-clk-wuninitialized-v1-1-ea9041240d10@kernel.org
[3] https://lore.kernel.org/all/OSYP286MB03120BABB25900E113ED42B7BC5CA@OSYP286MB0312.JPNP286.PROD.OUTLOOK.COM
[4] https://lore.kernel.org/all/TYAP286MB03151148AF8C054621DD55C3BC23A@TYAP286MB0315.JPNP286.PROD.OUTLOOK.COM

Tested on Motorola MWR03 (MT7628)
Tested on Haier HW-L1W (MT7620)

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2023-07-30 13:09:23 +02:00
Shiji Yang
8cacf2bda8 ramips: add proper system clock and reset driver support for mt7621
This series of upstream patches makes the system controller node as a
reset provider[1][2], and it also includes some clock and reset driver
fixes[3][4]. Meanwhile, all clocks and resets properties in the SoC
device tree have been updated to be compatible with the new driver.

[1] https://lore.kernel.org/r/20220110114930.1406665-2-sergio.paracuellos@gmail.com
[2] https://lore.kernel.org/r/20220210094859.927868-2-sergio.paracuellos@gmail.com
[3] https://lore.kernel.org/r/20221217074806.3225150-1-sergio.paracuellos@gmail.com
[4] https://lore.kernel.org/r/20230206083305.147582-1-sergio.paracuellos@gmail.com

Tested on RAISECOM MSG1500 X.00

Signed-off-by: John Thomson <git@johnthomson.fastmail.com.au>
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2023-07-30 13:09:23 +02:00
Shiji Yang
b4ea49ad44 ramips: pinctrl: support requesting different functions for same group
MT7620 wireless radio needs change the pin group function between
"gpio" and "pa" during the calibration process. However, ralink
pinctrl driver doesn't support requesting different functions for
the same group. This patch enables pinctrl consumers to perform
such operations.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2023-07-29 15:07:11 +01:00
Rafał Miłecki
03b3284805 ramips: use NVMEM cells with mt76 EEPROM for Netgear R6220 & WNDR3700 v5
This uses new upstream DT binding. It's more generic (NVMEM) compared to
the old one (MTD).

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2023-07-28 19:42:46 +02:00