Commit Graph

136 Commits

Author SHA1 Message Date
Daniel Golle
98e6ea32a4 mediatek: use DEVICE_DTC_FLAGS and drop DTC_FLAGS where not needed
The MT7986 RFB was intended to use device tree overlays and for that
reason modified DTC_FLAGS. zyxel_ex5601-t0-stock later on probably
copied it from there. Both boards do not actually use device tree
overlays, so remove setting DTC_FLAGS from both.

The BPi-R3 does use device tree overlays, use DEVICE_DTC_FLAGS to give
it an extra 4kb of padding for overlays to be applied.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-06-06 13:26:19 +01:00
Daniel Golle
7b536c4ec9 mediatek: use DEVICE_DTC_FLAGS for BPi-R64
Make sure there is an extra 4kb of padding to apply device tree overlays
on the BPi-R64.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-06-06 13:09:28 +01:00
Daniel Golle
7a0ec001ff mediatek: sync MT7986 device trees with upstream
Sync device tree files for MT7986 boards with what landed in upstream
Linux tree to easy maintainance and also allow for a smooth update to
Linux 6.1.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-06-05 11:36:32 +01:00
Daniel Golle
34bb33094a mediatek: use updated device tree overlay mechanism for BPi-R64
Use new device tree overlay mechanism for the BananaPi BPi-R64 board.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-06-05 11:36:32 +01:00
Daniel Golle
037ce27244 mediatek: follow-up with renamed Build/bl2 and Build/bl31-uboot
Use renamed build step names for all boards which were not handled by
commit c620409d58 ("mediatek: filogic: add uboot build for mt7981")
and now breaking the build.

Fixes: c620409d58 ("mediatek: filogic: add uboot build for mt7981")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-05-27 21:57:01 +01:00
Chukun Pan
dc2d4d7393 mediatek: filogic: add Qihoo 360T7 support
Hardware specification:
  SoC: MediaTek MT7981B 2x A53
  Flash: ESMT F50L1G41LB 128MB
  RAM: MT5CC128M16JR-EK 256MB
  Ethernet: 4x 10/100/1000 Mbps
  Switch: MediaTek MT7531AE
  WiFi: MediaTek MT7976C
  Button: Reset, WPS
  Power: DC 12V 1A

Flash instructions:
  1. Attach UART, boot the stock firmware until
     the message about failsafe mode appears.
  2. Enter failsafe mode by pressing "f" and "Enter"
  3. Type "mount_root", then run
     "fw_setenv bootmenu_delay 3"
  4. Back up all mtd partitions before flashing.
  5. Reboot, U-Boot now presents a menu.
  6. Connect to your PC via the Gigabit port of the router,
     set a static ip on the ethernet interface of your PC.
     (ip 192.168.1.254, gateway 192.168.1.1)
  7. Select "Upgrade ATF BL2", then use this file:
     openwrt-mediatek-filogic-qihoo_360t7-preloader.bin
  8. Select "Upgrade ATF FIP", then use this file:
     openwrt-mediatek-filogic-qihoo_360t7-bl31-uboot.fip
  9. Download the initramfs image, and type "reset",
     waiting for tftp recovery to complete.
  a. After openwrt boots up, perform sysupgrade.

Note:
  1. Since NMBM is disabled, we must back up all partitions.
  2. Flash instructions is based on commit 28df7f7.

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
2023-05-27 11:17:08 +01:00
Chukun Pan
c620409d58 mediatek: filogic: add uboot build for mt7981
Rename previous uboot build to mt7986-*.

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
2023-05-27 11:01:45 +01:00
Daniel Golle
43d27b0252 mediatek: fix, clean and unify SD card image generation
Make sure sub-images on the SD card are size-checked, allow
generating SD card without squashfs and/or initramfs.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-05-26 14:31:36 +01:00
Sam Shih
e3a681bab4 mediatek: add basic mt7988 device tree support
This add basic device tree support for mediatek MT7988 SoC

Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-05-23 15:53:22 +01:00
Daniel Golle
d6fef27f2d mediatek: mt7623: build SD card without all filesystems
Allow building SD card images without having both initramfs and squashfs
present on the card, just like it has already been done for the mt7622
and filogic subtargets.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-05-22 23:04:09 +01:00
Pietro Ameruoso
1c05388ab0 mediatek: add support for Zyxel EX5601-T0 router
Zyxel EX5601-T0 specifics
--------------
The operator specific firmware running on the Zyxel branded
EX5601-T0 includes  U-Boot modifications affecting the OpenWrt
installation.

Partition Table
| dev  | size     | erasesize | name          |
| ---- | -------- | --------- | ------------- |
| mtd0 | 20000000 | 00040000  | "spi0.1"      |
| mtd1 | 00100000 | 00040000  | "BL2"         |
| mtd2 | 00080000 | 00040000  | "u-boot-env"  |
| mtd3 | 00200000 | 00040000  | "Factory"     |
| mtd4 | 001c0000 | 00040000  | "FIP"         |
| mtd5 | 00040000 | 00040000  | "zloader"     |
| mtd6 | 04000000 | 00040000  | "ubi"         |
| mtd7 | 04000000 | 00040000  | "ubi2"        |
| mtd8 | 15a80000 | 00040000  | "zyubi"       |

The router boots BL2 which than loads FIP (u-boot).
U-boot has hardcoded a command to always launch Zloader "mtd read zloader 0x46000000" and than "bootm". Bootargs are deactivated.
Zloader is the zyxel booloader which allow to dual-boot ubi or ubi2, by default access to zloader is blocked.
Too zloader checks that the firmware contains a particolar file called zyfwinfo.
Additional details regarding Zloader can be found here:
https://hack-gpon.github.io/zyxel/
https://forum.openwrt.org/t/adding-openwrt-support-for-zyxel-ex5601-t0/155914

Hardware
--------
SOC: MediaTek MT7986a
CPU: 4 core cortex-a53 (2000MHz)
RAM: 1GB DDR4
FLASH: 512MB SPI-NAND (Micron xxx)
WIFI: Wifi6 Mediatek MT7976 802.11ax 5 GHz 4x4 + 2.4GHZ 4x4
ETH: MediaTek MT7531 Switch + SoC
3 x builtin 1G phy (lan1, lan2, lan3)
1 x MaxLinear GPY211B 2.5 N-Base-T phy5 (lan4)
1 x MaxLinear GPY211B 2.5Gbit xor SFP/N-Base-T phy6 (wan)
USB: 1 x USB 3.2 Enhanced SuperSpeed port
UART: 3V3 115200 8N1 (Pinout: GND KEY RX TX VCC)
VOIP: 2 FXS ports for analog phones

MAC Address Table
-----------------
eth0/lan    Factory 0x002a
eth1/wan    Factory 0x0024
wifi 2.4Ghz Factory 0x0004
wifi 5Ghz   Factory 0x0004 + 1

Serial console (UART)
---------------------
+-------+-------+-------+-------+-------+
| +3.3V |  RX   |  TX   |  KEY  |  GND  |
+---+---+-------+-------+-------+-------+
    |
    +--- Don't connect

Installation
------------
Keep in mind that openwrt can only run on the UBI partition, the openwrt firmware is not able to understand the zloader bootargs.
The procedure allows restoring the UBI partition with the Zyxel firmware and retains all the OEM functionalities.

1. Unlock Zloader (this will allow to swap manually between partitions UBI and UBI2):
- Attach a usb-ttl adapter to your computer and boot the router.
- While the router is booting at some point you will read the following: `Please press Enter to activate this console.`
- As soon as you read that press enter, type root and than press enter again (just do it, don't care about the logs scrolling).
- Most likely the router is still printing the boot log, leave it boot until it stops.
- If everything went ok you should have full root access "root@EX5601-T0:/#".
- Type the following command and press enter: "fw_setenv EngDebugFlag 0x1".
- Reboot the router.
- As soon as you read `Hit any key to stop autoboot:` press Enter.
- If everything went ok you should have the following prompt: "ZHAL>".
- You have successfully unlocked zloader access, this procedure must be done only once.

2. Check the current active partition:
- Boot the router and repeat the steps above to gain root access.
- Type the following command to check the current active image: "cat /proc/cmdline".
- If `rootubi=ubi` it means that the active partition is `mtd6`
- If `rootubi=ubi2` it means that the active partition is `mtd7`
- As mentioned earlier we need to flash openwrt into ubi/mtd6 and never overwrite ubi2/mtd7 to be able to fully roll-back.
- To activate and boot from mtd7 (ubi2) enter into ZHAL> command prompt and type the following commands:
atbt 1  # unlock write
atsw    # swap boot partition
atsr    # reboot the router
- After rebooting check again with "cat /proc/cmdline" that you are correctly booting from mtd7/ubi2
- If yes proceed with the installation guide. If not probably you don't have a firmware into ubi2 or you did something wrong.

3. Flashing:
- Download the sysupgrade file for the router from openwrt, than we need to add the zyfwinfo file into the sysupgrade tar.
Zloader only checks for the magic (which is a fixed value 'EXYZ') and the crc of the file itself (256bytes).
I created a script to create a valid zyfwinfo file but you can use anything that does exactly the same:
https://raw.githubusercontent.com/pameruoso/OpenWRT-Zyxel-EX5601-T0/main/gen_zyfwinfo.sh
- Add the zyfwinfo file into the sysupgrade tar.
- Enter via telnet or ssh into the router with admin credentials
- Enter the following commands to disable the firmware and model checks
"zycli fwidcheck off" and "zycli modelcheck off"
- Open the router web interface and in the update firmware page select the "restore default settings option"
- Select the sysupgrade file and click on upload.
- The router will flash and reboot itself into openwrt from UBI

4. Restoring and going back to Zyxel firmware.
- Use the ZHAL> command line to manually swap the boot parition to UBI2 with the following:
atbt 1  # unlock write
atsw    # swap boot partition
atsr    # reboot the router
- You will boot again the Zyxel firmware you have into UBI2 and you can flash the zyxel firmware to overwrite the UBI partition and openwrt.

Working features
----------------
3 gbit lan ports
Wifi
Zyxel partitioning for coexistance with Zloader and dual boot.
WAN SFP port (only after exporting pins 57 and 10. gpiobase411)
leds
reset button
serial interface
usb port
lan ethernet 2.5 gbit port (autosense)
wan ethernet 2.5 gbit port (autosense)

Not working
----------------
voip (missing drivers or proper zyxel platform software)

Swapping the wan ethernet/sfp xor port
----------------
The way to swap the wan port between sfp and ethernet is the following:
export the pins 57 and 10.
Pin 57 is used to probe if an sfp is present.
If pin 57 value is 0 it means that an sfp is present into the cage (cat /sys/class/gpio/gpio468/value).
If pin 57 value is 1 it means that no sfp is inserted into the cage.
In conclusion by default both 57 an 10 pins are by default 1, which means that the active port is the ethernet one.
After inserting an SFP pin 57 will become 0 and you have to manually change the value of pin 10 to 0 too.
This is totally scriptable of course.

Leds description
------------
All the leds are working out of the box but the leds managed by the 2 maxlinear phy (phy 5 lan, phy6 wan).
To activate the phy5 led (rj45 ethernet port led on the back of the router) you have to use mdio-tools.
To activate the phy6 led (led on the front of the router for 2.5gbit link) you have to use mdio-tools.
Example:
Set lan5 led to fast blink on 2500/1000, slow blink on 10/100:
mdio mdio-bus mmd 5:30 raw 0x0001 0x33FC

Set wan 2.5gbit led to constant on when wan is 2.5gbit:
mdio mdio-bus mmd 6:30 raw 0x0001 0x0080

Signed-off-by: Pietro Ameruoso <p.ameruoso@live.it>
2023-05-22 17:58:59 +02:00
Daniel Golle
a384490b10 mediatek: fix append-gl-metadata when running in buildbot
Use same logic as in append-metadata so build doesn't fail in case of
missing build-key (it was previously failing on the buildbot runners).

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-05-19 09:34:22 +01:00
Daniel Golle
fd0118c0a5 mediatek: remove left-over reference to make_gl_metadata.py
When adding support for the GL.iNet GL-MT3000 a reference to the
non-existent make_gl_metadata.py script was accidentally added.
Remove it, flashing from vendor firmware also works fine without that.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-05-18 11:24:07 +01:00
Daniel Golle
7cbe34170e mediatek: add support for the GL.iNet GL-MT3000
The MT-3000 is a pocket-sized Wi-Fi 6 router based on MediaTek MT7981.

Specification:
 - SoC: MediaTek MT7981B
 - CPU: 2x 1.3 GHz Cortex-A53
 - Flash: 256 MiB Macronix SPI NAND
 - RAM: 512 MiB Nanya DDR4
 - WLAN: 2.4 GHz, 5 GHz (MediaTek MT7976CN)
 - Ethernet:
    - 1x 10/100/1000 Mbps built-in PHY (LAN)
    - 1x 10/100/1000/2500 Mbps MaxLinear GPY211 PHY (WAN)
 - USB 3.0 port
 - Buttons: 1 button, 1 switch
 - LEDs: 1x light-blue, 1x warm-white
 - Serial console: internal 4-pin header, 115200 8n1
 - PWM controlled fan with tacho
 - Power: 5 VDC, 3 A (USB Type-C)

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-05-18 02:41:49 +01:00
David Bauer
c9cb6411c1 mediatek: add support for Cudy WR3000 v1
Hardware
--------
MediaTek MT7981 WiSoC
256MB DDR3 RAM
16MB SPI-NOR (XMC XM25QH128C)
MediaTek MT7981 2x2 DBDC 802.11ax 2T2R (2.4 / 5)
UART: 115200 8N1 3.3V
      [LEDS] VCC-GND-RX-TX [ETH]
      Header is located below the heatsink

Case
----
Unscrew the 4 bottom screws. Remove the top of the case by inserting a
small screwdriver into the ventilation holes and lift the top cover.

This works best by beginning near the ETH-ports. The top is clipped on
the front near the LEDs with two plastic clips. The back has a single
clip in the middle. Start at one of the back edges.

MAC-Addresses
-------------
80:AF:CA:00:F9:C6 LAN
80:AF:CA:00:F9:C7 WAN
80:AF:CA:00:F9:C6 W2
82:AF:CA:30:F9:C6 W5

Installation
------------

1. Connect to the serial port as described in the "Hardware" section.

2. Power on the device. Keep pressing the "0" key to enter the U-Boot
   shell.

3. Download the OpenWrt initramfs image. Place it on an TFTP server
   connected to the Cudy LAN ports. Make sure the server is reachable at
   192.168.1.2. Rename the image to "cudy3000.bin"

4. Download and boot the OpenWrt initramfs image.

   $ tftpboot 0x46000000 cudy3000.bin; bootm 0x46000000

5. Transfer the OpenWrt sysupgrade image to the device using scp.
   Install with sysupgrade.

Note: Cudy does not yet provide a image for disabling their
signature-protection. This has happened in the past. Make sure to check
the wiki for a possible easier installation method.

Signed-off-by: David Bauer <mail@david-bauer.net>
2023-05-18 01:46:13 +02:00
Chukun Pan
21be2c26d5 mediatek: add support for TP-Link TL-XDR4288/608x
Hardware specification:
  SoC: MediaTek MT7986A 4x A53
  Flash: ESMT F50L1G41LB 128MB
  RAM: ESMT M15T4G16256A 512MB
  Ethernet (Max Speed):
    XDR4288: 1x 2.5G Wan, 1x 2.5G Lan, 4x 1G Lan
    XDR6086: 1x 2.5G Wan, 1x 2.5G Lan, 1x 1G Lan
    XDR6088: 1x 2.5G Wan, 1x 2.5G Lan, 4x 1G Lan
  WiFi:
    XDR4288: MT7976DAN (2.4G 2T2R, 5G 3T3R)
    XDR6086/XDR6088:
      WiFi1: MT7976GN 2.4GHz 4T4R
      WiFi2: MT7976AN 5GHz 4T4R
  Button: Reset, WPS, Turbo
  USB: 1 x USB 3.0
  Power: DC 12V 4A

Flash instructions:
  1. Execute the following operation to open nc shell:
     https://openwrt.org/inbox/toh/tp-link/xdr-6086#rooting
  2. Replace the stock bootloader to OpenWrt's:
     dd bs=131072 conv=sync of=/dev/mtdblock9 if=/tmp/xxx-preloader.bin
     dd bs=131072 conv=sync of=/dev/mtdblock9 seek=28 if=/tmp/xxx-bl31-uboot.fip
  3. Connect to your PC via the Gigabit port of the router,
     set a static ip on the ethernet interface of your PC.
     (ip 192.168.1.254, gateway 192.168.1.1)
  4. Download the initramfs image, and restart the router,
     waiting for tftp recovery to complete.
  5. After openwrt boots up, perform sysupgrade.

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
[Add uboot build, fit and sysupgrade support, fix RealTek PHYs]
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-04-22 04:10:19 +01:00
Daniel Golle
e92b153e99 mediatek: introduce KERNEL_LOADADDR to Device/Default template
We need to reset KERNEL_LOADADDR if we use it on a per-device base.
Otherwise the previous value will be kept in case a device doesn't
define KERNEL_LOADADDR and relies on the default.

Move initializing KERNEL_LOADADDR to target/linux/mediatek/image/Makefile,
similar to how it's done also on the ramips target.

This fixes image size related breakage on devices which rely on the
default value of KERNEL_LOADADDR.

While at it use 0x48000000 which is more common than the previous default
0x44000000 for the filogic subtarget.

Fixed: e7c399bee6 ("filogic: add support for ASUS TUF-AX4200")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-04-05 17:12:55 +01:00
David Bauer
f25abdf144 mediatek: make TUF-AX4200 KERNEL simply expanded
The KERNEL variable was recursively expanded, breaking other devices.

Signed-off-by: David Bauer <mail@david-bauer.net>
2023-04-04 02:08:32 +02:00
Andrew Sim
ed2849958f mediatek: re-add wireless driver for TUF-AX4200
The wireless driver package was incorrectly removed from the TUF-AX4200
device-packages, resulting in images without wireless functionality.

Fixes: d98c4fb8bf ("mediatek: broaden filogic target description")

Signed-off-by: Andrew Sim <andrewsimz@gmail.com>
[rework commit description]
Signed-off-by: David Bauer <mail@david-bauer.net>
2023-03-29 17:03:42 +02:00
Daniel Golle
d98c4fb8bf mediatek: broaden filogic target description
The filogic subtarget now also supports MT7981 and will in future
also support MT7988. Reflect that in the target description.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-03-27 19:07:54 +01:00
David Bauer
e7c399bee6 filogic: add support for ASUS TUF-AX4200
Hardware
--------
SOC:   MediaTek MT7986
RAM:   512MB DDR3
FLASH: 256MB SPI-NAND (Winbond W25N02KV)
WIFI:  Mediatek MT7986 DBDC 802.11ax 2.4/5 GHz
ETH:   MediaTek MT7531 Switch
       MaxLinear GPY211C 2.5 N-Base-T PHY
UART:  3V3 115200 8N1 (Pinout silkscreened / Do not ocnnect VCC)

Installation
------------

1. Download the OpenWrt initramfs image. Copy the image to a TFTP server
   reachable at 192.168.1.66/24. Rename the image to tufax4200.bin.

2. Connect the TFTP server to the AX4200. Conect to the serial console,
   interrupt the autoboot process by pressing '4' when prompted.

3. Download & Boot the OpenWrt initramfs image.

   $ setenv ipaddr 192.168.1.1
   $ setenv serverip 192.168.1.66
   $ tftpboot 0x46000000 tufax4200.bin
   $ bootm 0x46000000

4. Wait for OpenWrt to boot. Transfer the sysupgrade image to the device
   using scp and install using sysupgrade.

   $ sysupgrade -n <path-to-sysupgrade.bin>

Missing features
----------------

 - The LAN port LEDs are driven by the switch but OpenWrt does not
   correctly configure the output.

Signed-off-by: David Bauer <mail@david-bauer.net>
2023-03-24 20:30:29 +01:00
Marcel Ziswiler
f6d2a23cbc mediatek: add support for Netgear WAX206
Specifications:
* SoC: MediaTek MT7622BV
* RAM: DDR3 512 MiB (Nanya NT5CC256M16ER-EK)
* Flash: SPI-NAND 256 MiB (Toshiba TC58CVG1S3HRAIJ)
* Wi-Fi 2.4/5 GHz 4T4R:
  * 2.4 GHz: MediaTek MT7622BV
  * 5 GHz: MediaTek MT7915AN/MT7975AN
* Ethernet: 4x 10/100/1000 Mbps LAN,
            1x 10/100/1000/2500 Mbps WAN (Realtek RTL8221B PHY)
* Switch: MediaTek MT7531AE
* LEDs/Keys: 8/1 (Power, Internet, LAN1, LAN2, LAN3, LAN4,
             Wifin and Wifia dual-colour LEDs + Reset pin)
* UART: Marked J19 on board VCC GND TX RX, beginning from "1". 3.3v,
        115200n8
* Power: 12 VDC, 2.5 A

Installation:
* Flash the factory image through the stock web interface, or TFTP to
  the bootloader. NMRP can be used to TFTP without opening the case.
* U-Boot allows booting an initramfs image via TFTP as follows:
  setenv ipaddr 192.168.1.1
  setenv serverip 192.168.1.100
  tftpboot openwrt-mediatek-mt7622-netgear_wax206-initramfs-recovery.itb
  bootm

Known Limitations:
* The 2.5G WAN port labeled 'wan' only works for speeds up to 1G at the
  moment. If connected to a multi-gig port the speed has to be manually
  set to 1G/full either for the switch port or in OpenWrt. For example
  add the following to /etc/rc.local to set it on boot:
  /usr/sbin/ethtool -s wan speed 1000 duplex full

Revert to stock firmware:
* Flash the stock firmware to the bootloader using TFTP/NMRP.

References to WAX206 GPL source:
https://www.downloads.netgear.com/files/GPL/WAX206_V1.0.4.0_Source.rar

* openwrt/target/linux/mediatek/dts/mt7622-netgear-wax206.dts
  DTS file for this device.
* openwrt/target/linux/mediatek/image/mt7622.mk
  Image creation code for this device

Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
[fix WAN port (1G only), adjust partition layout, adjust image creation]
Signed-off-by: Thomas Kupper <thomas.kupper@gmail.com>
2023-02-18 15:46:45 +01:00
Shiji Yang
9a07895729 mt76: add stand-alone MT7622 firmware package
Add a separate firmware package to avoid installing the MT7615 firmware
on all MT7622 target devices by default. Now we only add MT7615 firmware
packages for devices that use MT7615E. This commit also removes the
explicit dependency on kmod-mt7615e to refine the package dependency.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2023-01-07 17:11:00 +01:00
Shiji Yang
fc9dd3f083 mt76: add stand-alone MT7915 firmware package
The mt7915e driver supports MT7915, MT7916 and MT7986 chips. And Only
MT7915 series chips need the MT7915 firmware. To save storage, extract
them from the common code package and create a new package to provide
the firmware.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2023-01-07 17:11:00 +01:00
Chuanhong Guo
d29dbf052a
mediatek: drop redmi-ax6000 variant with modified env
This variant uses xiaomi factory u-boot and modified u-boot-env &
bootcmd.
By modifying uboot-env, the xiaomi firmware recovery provided in
the vendor u-boot doesn't work anymore. It's possible to put
u-boot into a state where it refuese to take any serial input.
If the u-boot is in this state, users can't restore their
firmware without taking the flash off the board.
We now have a -stock variant where the vendor u-boot is used in
a way that xiaomi firmware recovery still works, and a -ubootmod
variant where we get rid of all xiaomi components, have more
usable space and no uart console lock. These two should cover all
use cases and we don't need this variant anymore.
Drop this redmi-ax6000 variant. Existing users of this variant
should perform a u-boot mod or restore to the -stock layout.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2022-12-30 16:11:59 +08:00
Furong Xu
8bac5dc18a mediatek: add new layout for Xiaomi Redmi Router AX6000 for OpenWrt U-Boot
This new layout is only bootable with OpenWrt U-Boot. It reuses the
two crash partions and expands the ubi partion to the end of whole flash.

Do not use this layout with stock U-Boot!

Signed-off-by: Furong Xu <xfr@outlook.com>
2022-12-29 03:00:31 +00:00
Chen Minqiang
18bea173a6 mediatek: add alternative stock layout for Xiaomi Redmi Router AX6000
In this implementation, the flash partition layout is adjusted to avoid
modifying the uboot environment of mtdparts. This ensures that the 30M
ubi_kernel partition remains aligned with the stock ubi partition, and
the kernel volume is placed in it. This allows the stock uboot to boot
from it without changing the mtdparts, which is useful for reverting back
to the stock firmware using Xiaomi Firmware Tools. In actual testing,
modifying mtdparts has been found to break Xiaomi Firmware Tools.

1. use ARTIFACTS to generate initramfs-factory.ubi for easy installation.
2. The NAND flash layout is changed to allow for reverting back to the
   stock firmware.
3. Before performing sysupgrade, do some cleanup in platform_pre_upgrade
   to ensure a clean installation of OpenWRT.
4. Setup the uboot env to ensure that the system always boot, which can
   be helpful for users who may forget to do this before sysupgrade in
   the initramfs.

New flash instructions:
1. Gain ssh access. Please refer to:
   https://openwrt.org/toh/xiaomi/redmi_ax6000#installation)

2. Check which system current u-boot is loading from:
   COMMAND: `cat /proc/cmdline`
   sample OUTPUT: `console=ttyS0,115200n1 loglevel=8 firmware=1 uart_en=1`
   if firmware=1, current system is ubi1
   if firmware=0, current system is ubi0

3. Setup nvram and write the firmware:
   If the current system is ubi1, please set it up so that the next time
   it will boot from ubi, and write the firmware to ubi:
```
nvram set boot_wait=on
nvram set uart_en=1
nvram set flag_boot_rootfs=0
nvram set flag_last_success=0
nvram set flag_boot_success=1
nvram set flag_try_sys1_failed=0
nvram set flag_try_sys2_failed=0
nvram commit
ubiformat /dev/mtd8 -y -f /tmp/initramfs-factory.ubi
```
   If the current system is ubi, please set it up so that the next time
   it will boot from ubi1, and write the firmware to ubi1:
```
nvram set boot_wait=on
nvram set uart_en=1
nvram set flag_boot_rootfs=1
nvram set flag_last_success=1
nvram set flag_boot_success=1
nvram set flag_try_sys1_failed=0
nvram set flag_try_sys2_failed=0
nvram commit
ubiformat /dev/mtd9 -y -f /tmp/initramfs-factory.ubi
```

4. After rebooting, the system should now boot into the openwrt initramfs.
   Flash the squashfs-sysupgrade.bin via using ssh or luci.
```
sysupgrade -n /tmp/squashfs-sysupgrade.bin
```
Done.

For existing users of the Redmi AX6000 running OpenWrt, here are the steps to
switch to this new layout:

1. Flash initramfs-factory.ubi
```
mtd -r -e ubi write /tmp/initramfs-factory.ubi ubi
```

2. After rebooting, the system will boot into the new openwrt-initramfs.
Log in and perform a sysupgrade to complete the process.
```
sysupgrade -n /tmp/squashfs-sysupgrade.bin
```

Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2022-12-17 15:04:16 +08:00
Furong Xu
d9e1362581 mediatek: add LED support for Xiaomi Redmi AX6000
add DT nodes and default package for the LEDs on Redmi AX6000

Signed-off-by: Furong Xu <xfr@outlook.com>
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2022-12-16 21:42:02 +08:00
Alex Hansen
7dbac3433f mediatek: add support for reyee AX3200-E5
This is yet another model of the Ruijie RG-EW3200GX PRO with a slightly
different flash layout, install process is the same.

Specifications:
SoC: MT7622B
RAM: 256MB
Flash: XMC XM25QH128C or Winbond WQ25Q128JVSQ 16MB SPI NOR
Ethernet: 5x1GbE
Switch: MT7531BE
WiFi: 2.4G: MT7622 5G: MT7915AN+MT7975AN
3LEDs: System LED(blue) + Mesh LED(green) + Mesh LED(red)
2Keys: Mesh button + Reset button
UART: Marked J19 on board. 3.3v, 115200n1
Power: 12V 2.5A

Flash instruction:
1. Serve the initramfs.img using a TFTP server with address 10.10.10.3.
2. Interrupt the uboot startup process via UART.
3. Select "System Load Linux to SDRAM via TFTP" item.
4. (important) Back up firmware(mtd7) partitions with:
    dd if=/dev/mtd7 of=/tmp/firmware.bin
    and then download the firmware.bin image via SCP.
5. Flash the OpenWrt sysupgrade firmware.

Recovery stock firmware:

1. Transfer the firmware.bin image to the device.
2. Flash the image with:
    mtd write firmware.bin firmware

Signed-off-by: Alex Hansen <mralexh123@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-12-06 12:43:15 +00:00
Felix Fietkau
4f1e54801e mediatek: drop the use of device tree overlays on mt7986a-rfb board
The boot loader does not support it. Instead make NAND the default image for
this board

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-11-09 20:43:45 +01:00
Chukun Pan
641e4f2f04 mediatek: add Xiaomi Redmi Router AX6000 support
Hardware specification:
  SoC: MediaTek MT7986A 4x A53
  Flash: ESMT F50L1G41LB 128 MB
  RAM: K4A4G165WF-BCWE 512 MB
  Ethernet: 4x 10/100/1000 Mbps
  WiFi1: MT7976GN 2.4GHz ax 4x4
  WiFi2: MT7976AN 5GHz ax 4x4
  Button: Mesh, Reset

Flash instructions:
  1. Gain ssh and serial port access, see the link below:
     https://openwrt.org/toh/xiaomi/redmi_ax6000#installation
  2. Use ssh or serial port to log in to the router, and
     execute the following command:
     nvram set boot_wait=on
     nvram set flag_boot_rootfs=0
     nvram set flag_boot_success=1
     nvram set flag_last_success=1
     nvram set flag_try_sys1_failed=8
     nvram set flag_try_sys2_failed=8
     nvram commit
  3. Set a static ip on the ethernet interface of your computer
     (e.g. default: ip 192.168.31.100, gateway 192.168.31.1)
  4. Download the initramfs image, rename it to initramfs.bin,
     and host it with the tftp server.
  5. Interrupt U-Boot and run these commands:
     setenv mtdparts nmbm0:1024k(bl2),256k(Nvram),256k(Bdata),2048k(factory),2048k(fip),256k(crash),256k(crash_log),112640k(ubi)
     saveenv
     tftpboot initramfs.bin
     bootm
  6. After openwrt boots up, use scp or luci web
     to upload sysupgrade.bin to upgrade.

Revert to stock firmware:
  Restore mtdparts back to default, then use the
  vendor's recovery tool (Windows only).

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
2022-10-30 14:30:22 +00:00
Daniel Golle
f38276c9be mediatek: filogic: enable thermal, I2C and PWM of the BPi-R3
Setup thermal zone, select pins and enabled drivers for I2C (on 26-pin
GPIO bank) and PWM (1x fan and 1x GPIO bank).

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-10-07 16:45:10 +01:00
Yoonji Park
c27279dc26 mediatek: add support for ipTIME A6004MX Add basic support for ipTIME A6004MX.
Hardware:
SoC: MediaTek MT7629 Cortex-A7 (ARMv7 1.25GHz, Dual-Core)
RAM: DDR3 128MB
Flash: Macronix MX35LF1GE4AB (SPI-NAND 128MB)
WiFi: MediaTek MT7761N (2.4GHz) / MediaTek MT7762N (5GHz) - no driver
Ethernet: SoC (WAN) / MediaTek MT7531 (LAN x4)
UART: [GND, RX, TX, 3.3V] (115200)

Installation:
- Flash recovery image with TFTP recovery

Revert to stock firmware:
- Flash stock firmware with TFTP recovery

TFTP Recovery method:
1. Unplug the router
2. Hold the reset button and plug in
3. Release when the power LED stops flashing and go off
4. Set your computer IP address manually to 192.168.0.x / 255.255.255.0
5. Flash image with TFTP client to 192.168.0.1

Signed-off-by: Yoonji Park <koreapyj@dcmys.kr>
2022-09-12 01:43:49 +01:00
Daniel Golle
a34cd4f66a mediatek: bananapi-r3: remove kmod-btmtkuart from default packages
The package kmod-btmtkuart is specific for MT7622 and isn't available
for MT7986 (which doesn't have this built-in Bluetooth like MT7622).

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-09-10 03:23:20 +01:00
Daniel Golle
007c8809c1 mediatek: fix typo in bpi-r64 image recipe
Janusz Dziedzic reported a typo introduced by a recent commit. Fix it.

Fixes: 50c892d67b ("mediatek: bpi-r64: make initramfs/recovery optional")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-09-08 19:30:56 +01:00
Daniel Golle
50c892d67b mediatek: bpi-r64: make initramfs/recovery optional
Only include recovery image in SD card image generated for the
BananaPi BPi-R64 if building with CONFIG_TARGET_ROOTFS_INITRAMFS
This allows to build images larger than 32 MB (the limit for
initramfs/recovery image) by deselecting initramfs.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-09-08 02:51:11 +01:00
Daniel Golle
1a6f6a1e8c mediatek: bpi-r3: make initramfs/recovery optional
Only include recovery image in SD card image generated for the
BananaPi BPi-R3 if building with CONFIG_TARGET_ROOTFS_INITRAMFS.
This allows to build images larger than 32 MB (the limit for
initramfs/recovery image) by deselecting initramfs.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-09-08 02:51:11 +01:00
Daniel Golle
a96382c1bb mediatek: add support for Bananapi BPi-R3
The Bananapi BPi-R3 is a development router board built around the
MediaTek Filogic 830 (MT7986A) SoC.
The board can boot either from microSD, SPI-NAND, SPI-NOR or eMMC.
Only either SPI-NAND or SPI-NOR can be used at the same time, also only
either microSD or eMMC can be used. The various storage options can be
selected using small SMD switches on the board.

Specs:
 * MediaTek MT7986A (Filogic 830) 4x ARM Cortex A53
 * 4T4R 2.4G 802.11bgnax (MT7975N)
 * 4T4R 5G 802.11anac/ax (MT7975P)
 * 2 GB DDR4 RAM
 * 8 GB eMMC
 * 128 MB SPI-NAND flash
 * 32 MB SPI-NOR flash
 * on-board MT7531 GbE switch
 * 2x SFP+ (1 GbE / 2.5 GbE)
 * 5x GbE network port
 * miniPCIe slot (only USB 2.0 connected)
 * uSIM slot (connected to miniPCIe interface)
 * M.2 KEY-E PCIe interface (PCIe x2)
 * microSD card interface
 * 26 PIN GPIO

Hardware details: https://wiki.banana-pi.org/Banana_Pi_BPI-R3

Working:
 * all 4 boot methods incl. installation via U-Boot, sysupgrade, ...
 * copper LAN and WAN ports
 * SFP1 (connected to gmac1, eth1 in Linux)
 * WiFi
 * LEDs
 * Buttons
 * PSTORE/ramoops based dual-boot

Not Working (missing driver features):
 * SFP2 (connected to MT7531 switch)

Untested:
 * M.2/NGFF slot (PCIe x2)
 * mPCIe slot (USB 2.0 + SIM)

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-08-30 13:36:28 +01:00
Felix Fietkau
cffc77ae55 mediatek: add filogic subtarget
Initially this covers MT7986 only, but it will later be expanded to cover other
Filogic branded platforms by MediaTek

Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-08-28 20:33:15 +01:00
Henrik Riomar
31d86a1a11 mediatek: add Ubiquiti UniFi 6 LR v2 targets
Add targets:
 * Ubiquiti UniFi 6 LR v2
 * Ubiquiti UniFi 6 LR v2 (U-Boot mod)

This target does not have a RGB led bar like v1 did

Used target/linux/ramips/dts/mt7621_ubnt_unifi.dtsi as inspiration

The white dome LED is default-on, blue will turn on when the system is
in running state

Signed-off-by: Henrik Riomar <henrik.riomar@gmail.com>
2022-06-11 19:51:33 +01:00
Henrik Riomar
5c8d3893a7 mediatek: new target ubnt_unifi-6-lr-v1-ubootmod
based on current ubnt_unifi-6-lr-ubootmod

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
[added SUPPORTED_DEVICES for compatibility with existing setups]
Signed-off-by: Henrik Riomar <henrik.riomar@gmail.com>
2022-06-11 19:51:18 +01:00
Henrik Riomar
15a02471bb mediatek: new target mt7622-ubnt-unifi-6-lr-v1
Based on current mt7622-ubnt-unifi-6-lr, this is a preparation for
adding a v2 version of this target

* v1 - with led-bar
* v2 - two simple GPIO connected LEDs (in later commits)

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
[added SUPPORTED_DEVICES for compatibility with existing setups]
Signed-off-by: Henrik Riomar <henrik.riomar@gmail.com>
2022-06-11 19:50:26 +01:00
INAGAKI Hiroshi
58b3b557b6 mediatek: mt7622: add support for ELECOM WRC-X3200GST3
ELECOM WRC-X3200GST3 is a 2.4/5 GHz band 11ax (Wi-Fi 6) router, based on
MT7622B.

Specifications:

- SoC		: MediaTek MT7622B
- RAM		: DDR3 512 MiB (Nanya NT5CC256M16ER-EK)
- Flash		: SPI-NAND 128 MiB (Winbond W25N01GVZEIG)
- WLAN		: 2.4/5 GHz 4T4R
  - 2.4 GHz	: MediaTek MT7622B (SoC)
  - 5 GHz	: MediaTek MT7915A
- Ethernet	: 5x 10/100/1000 Mbps
  - Switch	: MediaTek MT7531
- LEDs/Keys	: 6x/4x (2x buttons, 1x slide-switch)
- UART		: through-hole on PCB
  - J19: 3.3V, GND, TX, RX from power jack side
  - 115200n8
- Power		: 12 VDC, 1.5 A

Flash instruction using factory image:

1. Boot WRC-X3200GST3 normally with "Router" mode
2. Access to "http://192.168.2.1/" and open firmware update page
   ("ファームウェア更新")
3. Select the OpenWrt factory image and click apply ("適用") button
4. Wait ~120 seconds to complete flashing

MAC Addresses:

LAN    : 04:AB:18:xx:xx:77 (Factory, 0x7FFF4 (hex))
WAN    : 04:AB:18:xx:xx:78 (Factory, 0x7FFFA (hex))
2.4 GHz: 04:AB:18:xx:xx:79 (Factory, 0x4     (hex))
5 GHz  : 04:AB:18:xx:xx:7A (none)

Note:

- currently, there is no "phy1tpt" trigger for 5 GHz wlan (MT7915) in
  "trigger" file of LEDs, use "phy1radio" trigger instead

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2022-05-21 22:27:01 +01:00
Chuanhong Guo
d9ea9c06e9 mediatek: build ubnt-ledbar as a module
The config for LEDS_UBNT_LEDBAR doesn't stay in mt7629 kconfig because
of its I2C dependency. Build it as a module and let buildroot handle
this config option instead.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2022-04-30 23:13:33 +08:00
Richard Huynh
9f9477b275 mediatek: Add support for Xiaomi Redmi Router AX6S
Also known as the "Xiaomi Router AX3200" in western markets,
but only the AX6S is widely installation-capable at this time.

SoC: MediaTek MT7622B
RAM: DDR3 256 MiB (ESMT M15T2G16128A)
Flash: SPI-NAND 128 MiB (ESMT F50L1G41LB or Gigadevice GD5F1GQ5xExxG)
WLAN: 2.4/5 GHz 4T4R
2.4 GHz: MediaTek MT7622B
5 GHz: MediaTek MT7915E
Ethernet: 4x 10/100/1000 Mbps
Switch: MediaTek MT7531B
LEDs/Keys: 2/2 (Internet + System LED, Mesh button + Reset pin)
UART: Marked J1 on board VCC RX GND TX, beginning from "1". 3.3v, 115200n8
Power: 12 VDC, 1.5 A

Notes:
U-Boot passes through the ethaddr from uboot-env partition,
but also has been known to reset it to a generic mac address
hardcoded in the bootloader.

However, bdata is also populated with the ethernet mac addresses,
but is also typically never written to. Thus this is used instead.

Installation:
1. Flash stock Xiaomi "closed beta" image labelled
'miwifi_rb03_firmware_stable_1.2.7_closedbeta.bin'.
(MD5: 5eedf1632ac97bb5a6bb072c08603ed7)

2. Calculate telnet password from serial number and login

3. Execute commands to prepare device
nvram set ssh_en=1
nvram set uart_en=1
nvram set boot_wait=on
nvram set flag_boot_success=1
nvram set flag_try_sys1_failed=0
nvram set flag_try_sys2_failed=0
nvram commit

4. Download and flash image
On computer:
python -m http.server
On router:
cd /tmp
wget http://<IP>:8000/factory.bin
mtd -r write factory.bin firmware

Device should reboot at this point.

Reverting to stock:
Stock Xiaomi recovery tftp that accepts their signed images,
with default ips of 192.168.31.1 + 192.168.31.100.
Stock image should be renamed to tftp server ip in hex (Eg. C0A81F64.img)
Triggered by holding reset pin on powerup.

A simple implementation of this would be via dnsmasq's
dhcp-boot option or using the vendor's (Windows only)
recovery tool available on their website.

Signed-off-by: Richard Huynh <voxlympha@gmail.com>
2022-03-20 18:33:39 +00:00
Langhua Ye
ce8a33b021 mediatek: add support for Ruijie RG-EW3200GX PRO
X32 Pro is another product  name for it in the Chinese market.

Specifications:
- SoC: MT7622B
- RAM: 256MB
- Flash: XMC XM25QH128C or Winbond WQ25Q128JVSQ 16MB SPI NOR
- Ethernet: 5x1GbE
- Switch: MT7531BE
- WiFi: 2.4G: MT7622 5G: MT7915AN+MT7975AN
- 3LEDs: System LED(blue) + Mesh LED(green) + Mesh LED(red)
- 2Keys: Mesh button + Reset button
- UART: Marked J19 on board. 3.3v, 115200n1
- Power: 12V 2.5A

MAC addresses as verified by OEM firmware:
use   address    source
WAN   *:F4       ethaddr@product_info
LAN   *:F5
5g    *:F6
2g    *:F7

Flash instruction:
1. Serve the initramfs.img using a TFTP server with address 10.10.10.3.
2. Interrupt the uboot startup process via UART.
3. Select "System Load Linux to SDRAM via TFTP" item.
4. (important) Back up firmware(mtd7) partitions with:
        dd if=/dev/mtd7 of=/tmp/firmware.bin
   and then download the firmware.bin image via SCP.
5. Flash the OpenWrt sysupgrade firmware.

Recovery stock firmware:
1. Transfer the firmware.bin image to the device.
2. Flash the image with:
        mtd write firmware.bin firmware

Signed-off-by: Langhua Ye <y1248289414@outlook.com>
2022-03-05 21:06:35 +01:00
Daniel Golle
9ba7a83425
mediatek: mt7623: simplify partition generation
The two options 'emmc' and 'sdmmc' now became identical lines after
introducing CONFIG_TARGET_ROOTFS_PARTSIZE.
Remove the now useless if-clauses.

Fixes: a40b4d335a ("mediatek: use CONFIG_TARGET_ROOTFS_PARTSIZE")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-01-31 15:02:36 +00:00
Daniel Golle
f5865452ac
mediatek: mt7623: include regular AHCI PCI driver
The legacy image for the UniElec U7623-02 until now included
kmod-ata-ahci-mtk. The MT7623 chip doesn't have that IP and that
board uses a PCIe-connected AHCI controller for the SATA port and
mSATA-pins of the mPCIe socket. Hence include kmod-ata-ahci instead.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-01-25 00:38:28 +00:00
Daniel Golle
31872a38be
uboot-envtools: add configuration for UniElec U7623 board
Add U-Boot env settings to allow accessing the environment using
fw_printenv and fw_setenv tools on the UniElec U7623 board.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-01-23 20:20:42 +00:00
Daniel Golle
1ee75dd290
mediatek: mt7623: rework images for U7623-02 board
Users of older OpenWrt versions need sysupgrade using the *emmc.img.gz
file once which will upgrade U-Boot and switch to the new image layout.
Users of the vendor firmware need to first flash the legacy image to
then sunsequently carry out a full-flash upgrade.

Alternatively the board can also be flashed using MediaTek's
proprietary SP Flash Tool.

Configuration as well as persistent MAC address will be lost once at
this point and you will have to redo (or restore) all configuration
manually. To restore the previous persistent MAC address users may set
it manually using

fw_setenv ethaddr 00:11:22:33:44:55

For future upgrades once running OpenWrt past this commit, the usual
*sysupgrade.itb file can be used.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-01-23 20:20:37 +00:00