Manually rebased:
bcm53xx/patches-5.10/180-usb-xhci-add-support-for-performing-fake-doorbell.patch
All patches automatically rebased.
Signed-off-by: John Audia <therealgraysky@proton.me>
[Move gro_skip in 680-NET-skip-GRO-for-foreign-MAC-addresses.patch to old position]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Linksys EA8500 is currently broken after the kernel 5.15 bump. Disable
compiling it by default from buildbot to prevent brick from the user.
Don't mark it as BROKEN to permit user to compile images and permit devs
to bisect the problem with the users.
The current problem with the device is that the switch is not detected
and we can't comunicate with it via MDIO.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Linksys EA8500 is currently broken after the kernel 5.15 bump. Disable
compiling it by default from buildbot to prevent brick from the user.
Don't mark it as BROKEN to permit user to compile images and permit devs
to bisect the problem with the users.
The current problem with the device is that the switch is not detected
and we can't comunicate with it via MDIO.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This patch was wrongly dropped with the assumption that it was moved to
generic. This wasn't the case and caused the malfunction of the Asrock
G10 router.
Reintroduce it to fix Asrock G10 functionality.
Fixes: 8cc2caed58 ("ipq806x: 5:15: add testing kernel version")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Zyxel NGB6817 is the only router that use mmc for rootfs. Upstream
kernel dtsi have mmc-ddr-1_8v enabled for sddc1. This is wrong as mmc on
ipq806x is supplied by a fixed 3.3v regulator and can't operate at 1.8v.
This cause the sddc1 to malfunction and cause kernel panic.
In old 5.15 version this was disabled but it was put in addition to many
other changes so it was dropped silently. Restore this patch to fix
working condition of such router.
Fixes: 88bf652 ("ipq806x: 5.15: replace dtsi patches with upstream version")
Fixes: #11000
Tested-by: Hendrik Koerner <koerhen@web.de>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
In refreshing DTS to the upstream version an unwanted change slipped in
the commit. The ASRock G10 dts got converted to DSA without any support.
Revert this to swconfig driver to restore normal functionality.
Fixes: 88bf652525 ("ipq806x: 5.15: replace dtsi patches with upstream version")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
We currently ignore ret of the nandc partition parser if unprotected
spare data is true. This is the case for ipq806x nand.
Backport patch that fix this error and correctly handle error from
partition parser.
Fixes: ae6a63bc97 ("ipq806x: 5.15: replace nandc patch with upstream version")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add 6.1 tag to upstream patch now that 6.1 got tagged. This permits to
track patch in a better way and directly drop them on kernel bump.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add multiple patch for krait-cc modernization and multiple fixup for the
driver. Also modify a patch to enable the qsb fixed clock and add pxo to
krait-cc node.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
nand_pins definition is now shipped in ipq8064 dtsi. Rework the
nand_pins definition for wg2600hp3 5.15 files.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The patch has changed implementation and now the binding has changed.
Replace the old binding with boot-partitions and reimplement the
definition with the new definition.
The new definition is:
<offset1 size1 offset2 size2 offset3 ...>
and now supports sparsed patch.
Also add missing binding in some dts and add the backup boot partition
to the boot-partitions list.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Remove useless spm patch as using the normal qcom,spm compatible is
enough to register it with no clks.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Use a new implementation by using a devfreq driver to scale the shared
cache of the krait cpu cores.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Backport devfreq new cpufreq based PASSIVE governor needed for devfreq
based fab and cache scaling.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reorganize dtsi patches with upstream version and drop dtsi in 5.15
files.
Also add an additional upstream patch for hwspinlock support.
Refresh all the dts with needed changes.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This doesn't cause any panic anymore and no regression are observed with
ath10k. Remove this additional patch.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Remove qcom adm Documentation patch that is not needed for the target.
Probably a leftover when the adm bus was added, now merged upstream.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
In preparation for a cleanup of 5.15 patches copy the files dir to 5.10
and 5.15 kernel version.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Removed following upstreamed patch:
* bcm53xx: 081-next-ARM_dts_BCM53015-add-mr26.patch
All other patches automagically rebased.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Add missing scaling_available_frequencies sysfs entry for dedicated
cpufreq driver.
This sysfs entry is not standard and each cpufreq driver needs to
provide it and declare it in the cpufreq driver struct attr.
Fixes: 5dbbefcbcc ("ipq806x: introduce dedicated krait cpufreq")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
All targets expect the malta target already activate the CONFIG_GPIOLIB
option. Move it to generic kernel configuration and also activate it for
malta.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The order of LAN ports shown in Luci is reversed compared to what is
written on the case of the device. Fix the order so that they match.
Fixes: #10275
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This is now built-in, enable so it won't propagate on target configs.
Link: https://lkml.org/lkml/2022/1/3/168
Fixes: 79e7a2552e ("kernel: bump 5.15 to 5.15.44")
Fixes: 0ca9367069 ("kernel: bump 5.10 to 5.10.119")
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
(Link to Kernel's commit taht made it built-in,
CRYPTO_LIB_BLAKE2S[_ARM|_X86] as it's selectable, 5.10 backport)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Hardware specs:
SoC: Qualcomm IPQ8065 (dual core Cortex-A15)
RAM: 512 MB DDR3
Flash: 256 MB NAND, 32 MB NOR
WiFi: QCA9983 2.4 GHz, QCA9984 5 GHz
Switch: QCA8337
Ethernet: 5x 10/100/1000 Mbit/s
USB: 1x USB 3.0 Type-A
Buttons: WPS, Reset
Power: 12 VDC, 2.5 A
Ethernet ports:
1x WAN: connected to eth2
4x LAN: connected via the switch to eth0 and eth1
(eth0 is disabled in OEM firmware)
MAC addresses (OEM and OpenWrt):
fw_env @ 0x00 d4🆎82:??:??:?a LAN (eth1)
fw_env @ 0x06 d4🆎82:??:??:?b WAN (eth2)
fw_env @ 0x0c d4🆎82:??:??:?c WLAN 2.4 GHz (ath1)
fw_env @ 0x12 d4🆎82:??:??:?d WLAN 5 GHz (ath0)
fw_env @ 0x18 d4🆎82:??:??:?e OEM usage unknown (eth0 in OpenWrt)
OID d4🆎82 is registered to:
ARRIS Group, Inc., 6450 Sequence Drive, San Diego CA 92121, US
More info:
https://openwrt.org/inbox/toh/arris/tr4400_v2
IMPORTANT:
This port requires moving the 'fw_env' partition prior to first boot to
consolidate 70% of the usable space in flash into a contiguous partition.
'fw_env' contains factory-programmed MAC addresses, SSIDs, and passwords.
Its contents must be copied to 'rootfs_1' prior to booting via initramfs.
Note that the stock 'fw_env' partition will be wiped during sysupgrade.
A writable 'stock_fw_env' partition pointing to the old, stock location
is included in the port to help rolling back this change if desired.
Installation:
- Requires serial access and a TFTP server.
- Fully boot stock, press ENTER, type in:
mtd erase /dev/mtd21
dd if=/dev/mtd22 bs=128K count=1 | mtd write - /dev/mtd21
umount /config && ubidetach -m 23 && mtd erase /dev/mtd23
- Reboot and interrupt U-Boot by pressing a key, type in:
set mtdids 'nand0=nand0'
set mtdparts 'mtdparts=nand0:155M@0x6500000(mtd_ubi)'
set bootcmd 'ubi part mtd_ubi && ubi read 0x44000000 kernel && bootm'
env save
- Setup TFTP server serving initramfs image as 'recovery.bin', type in:
set ipaddr 192.168.1.1
set serverip 192.168.1.2
tftpboot recovery.bin && bootm
- Use sysupgrade to install squashfs image.
This port is based on work done by AmadeusGhost <amadeus@jmu.edu.cn>.
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
[add 5.15 changes for 0069-arm-boot-add-dts-files.patch]
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Converts extraction entries from 11-ath10k-caldata into
nvmem-cells in the individual board's device-tree file.
Same as commit 2047058 ("ipq806x: utilize nvmem-cells
for pre-calibration data")
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Reviewed-by: Ansuel Smith <ansuelsmth@gmail.com>
There is a mr25h256 spi flash on this machine. From the mtd backup
of the stock firmware, this spi flash is empty.
[ 3.652745] spi_qup 1a280000.spi: IN:block:16, fifo:64, OUT:block:16,
fifo:64
[ 3.653925] spi-nor spi0.0: mr25h256 (32 Kbytes)
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Fix wrong CPU OPP for ipq8062. Revision of the SoC added an
extra 25mV for every pvs. Also fix the voltage min/max value
that were wrong.
Reviewed-by: Robert Marko robimarko@gmail.com
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
The existing device tree has incorrect definitions for usb3_0 and usb3_1
and the blocks they depend upon: their addresses and interrupts are
swapped. However, their clocks and resets are not. The result is that
the USB blocks are non-functional if only one of them is enabled.
This fix backports the definitions from mainline Linux 5.15 to
OpenWrt's 5.10 dtsi additions. See the relevant mainline code here:
https://github.com/torvalds/linux/blob/v5.17/arch/arm/boot/dts/qcom-ipq8064.dtsi#L1062-L1148
This fix does not break existing ports. But some ports may have enabled
both USB blocks even thought their board only implements one, because
enabling a single USB block would not have worked before this fix.
This means that revisiting all ports of ipq806x devices that implement
a single USB port is advised. This work must be done by maintainers that
can determine which USB block corresponds to the implemented port on
their hardware.
Note that this fix swaps the names of the hardware ports. This is
unfortunate, but will happen anyway when switching to kernel 5.15. Thus,
it is best to do this ASAP, before users get to depend on port names.
It is strongly recommended that this fix is backported to 22.03 before
its release. This will minimize the number of users affected by the port
name swap.
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
This commit add some enabled symbols to generic config.
LTO is only supported by clang compiler and therefore should
be disabled in the generic config instead of duplicating this
symbol in each target. CONFIG_LTO_NONE do this job.
The second group of symbols is enabled by the options available
in the generic config and is therefore added here:
* CONFIG_AF_UNIX_OOB is selected by CONFIG_NET && CONFIG_UNIX,
* CONFIG_BINARY_PRINTF is selected by CONFIG_BPF_SYSCALL,
* CONFIG_NET_SOCK_MSG is selected by CONFIG_BPF_SYSCALL && CONFIG_NET.
The other symbols are disabled and should be in the generic config.
This commit also removes these symbols from subtargets.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Fix dedicated cpufreq for kernel 5.15 as they changed module
order and now it can happen that cpufreq probe after cache driver.
Also add lock between cache scaling in set_target as it's now required
by opp functions.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Now that smem actually free the leaked parts, when
a rootfs partition is detected, the kernel panics as
it try to free the static space allocated for the "ubi"
name. Change the logic and fix the name at the allocate_partition
function to correctly free the space allocated by smem.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Refresh patch for 5.15
Rework tweak patch to sync with upstream ipq8064 dtsi and fix
regression introduced.
Rename nand_controller to nand in every dts.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Timo Schroeder reported:
"The TP-Link Archer VR2600v is stuck in a boot loop on written
snapshot image. It's able to boot using the snapshot uimage
though, but there ath10k firmware can't be found.
21.02.2 release version doesn't have either problem."
The VR2600v has a 512 byte header at the beginning of the
firmware that needs to be accounted for.
Fixes: f6a01d7f5c ("ipq806x: convert TP-Link Archer VR2600v to denx,uimage")
Reported-by: Timo Schroeder <der.timosch@gmail.com>
References: <https://github.com/openwrt/openwrt/issues/9467>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Add kmod-ramoops to the default set of device packages in
R7800 and XR500, so that the ramoops kernel crash logs
are provided by default for these routers.
The capability was earlier defined by 97158fe1 and cf346dfa,
but the feature was not yet turned on by default.
The possible kernel crashes are stored into /sys/fs/pstore/*
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Enable support for allocating user space page table entries in high memory [1],
for the targets which support this feature. This saves precious low memory
(permanently mapped, the only type of memory directly accessible by the kernel).
[1] https://www.kernel.org/doc/html/latest/vm/highmem.html
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Fixes following warning message during image building process:
Finalizing root filesystem...
root-ipq806x/lib/upgrade/asrock.sh: line 1: /lib/functions.sh: No such file or directory
Enabling boot
root-ipq806x/lib/upgrade/asrock.sh: line 1: /lib/functions.sh: No such file or directory
Enabling bootcount
Fixes#9350
Fixes: 98b86296e6 ("ipq806x: add support for ASRock G10")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Increase the kernel size from 3 MB to 4 MB for EA8500 and EA7500v1.
* modify the common .dtsi
* modify the kernel size in the image recipes
Define compat-version 2.0 to force factory image usage for sysupgrade.
Add explanation message. Reenable both devices.
As for 4MiB (and not more): Hannu Nyman noted that:
"We have lots of ipq806x devices with 4 MB kernel, so will
need action at that point in future in any case.
(Assuming that the bootloader did not have a 4 MB limit that
has been tested...)"
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
(squashed, added 4MiB notice of support in ipq806x)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Define the kernel crash log storage ramoops/pstore feature
for R7800 and its sister XR500.
Reference to the ramoops admin guide in upstream Linux:
https://www.kernel.org/doc/html/v5.10/admin-guide/ramoops.html
Tested with R7800.
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
The kernel of both images will no longer fit into
the 3072KiB / 3MiB kernel partition:
|Image Name: ARM OpenWrt Linux-5.10.100
|Created: Sat Feb 19 00:11:55 2022
|Image Type: ARM Linux Kernel Image (uncompressed)
|Data Size: 3147140 Bytes = 3073.38 KiB = 3.00 MiB
Disable both targets for now, until a solution is available.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Enabled `CONFIG_ALL_KMODS` and ran `make kernel_menuconfig` against
ipq806x to update defconfig.
The removed symbols are in fact present in
target/linux/generic/config-5.10. CONFIG_MDIO_DEVRES
was likely added due to this:
<https://elixir.bootlin.com/linux/v5.10.100/source/drivers/net/phy/Kconfig#L16>
Signed-off-by: John Audia <graysky@archlinux.us>
This device still had the legacy flash partitioning.
This is a problem, because neither the nvmem-cells
for mac-address and calibration. Nor the denx,uimage
mtd-splitter compatible would be picked up.
The patch also changes the node-names of the flash
and partition nodes to hopefully meet all the
current FDT trends.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Increase the available flash memory size in Netgear R7800
by repurposing the unused "netgear" partition that is
located after the firmware partition.
Available flash space for kernel+rootfs+overlay increases
by 68 MB from 32 MB to 100 MB.
In a typical build, overlay space increases from 15 to 85,
increasing the package installation possibilities greatly.
Reverting to the OEM firmware is still possible, as the OEM
firmware contains logic to initialise the "netgear" partition
if its contents do not match expectations. In OEM firmware,
"netgear" contains 6 UBI sub-partitions that are defined in
/etc/netgear.cfg and initialisation is done by /etc/preinit
This is based on fb8a578aa7
Signed-off-by: Mike Lothian <mike@fireburn.co.uk>
The recent device-tree modification that added pre-cal
nvmem-cells pushed the device's kernel+dtb over the
allotted 3072k KERNEL_SIZE.
> WARNING: Image file tplink_vr2600v-uImage is too big: 3147214 > 3145728
There was a previous kernel partition size upgrade:
commit 0c967d92b3 ("ipq806x: increase kernel partition size for the TP-Link Archer VR2600v")
It has been seemingly upgraded from a 2048k KERNEL_SIZE in the past.
The commit talks about using the MTD_SPLIT_TPLINK_FW. But looking at
the image make recipe, there is no code that adds a TPLINK header.
So instead the board will use "denx,umimage". This requires
MTD_SPLIT_UIMAGE_FW, but this is present thanks to some NEC devices.
(Maybe the MTD_CONFIG_ARGS can be removed as well? But it could be
there because of the padding at the beginning. This needs testing.)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
brings back the ath10k QCA9980 wifi nodes to which
it adds ASROCK's wifi calibration data. These are
now provided by the ath10k_firmware.git's board-2.bin.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
converts extraction entries from 11-ath10k-caldata into
nvmem-cells in the individual board's device-tree file.
The patch also moves previously existing referenced
nvmem-cells data nodes which were placed at the end
back into the partitions node. As well as removing
some duplicated properties from qcom-ipq8065-xr500.dts's
art (the included nighthawk.dtsi defines those already).
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Commit d284e6ef0f ("treewide: convert mtd-mac-address-increment* to
generic implementation") renamed "mtd-mac-address-increment" property
to "mac-address-increment". Convert remaining usages that have been
added after that.
Fixes: f44e933458 ("ipq806x: provide WiFI mac-addresses from dts")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
This moves bootargs-append support patch from ipq40xx and ipq806x to
generic. This way we can append additional boot arguments from DTS instead
of only being able to overwrite them.
This is a preparation for kirkwood support of ipTIME NAS1.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
This board has 512MiB of RAM like the R7800, and the VDSL modem is
attached to the second PCIe port.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This commit moves the device profiles within the ipq806x/generic
subtarget into their own includable .mk file, to support eventually
having subtargets other than generic.
Signed-off-by: Alex Lewontin <alex.c.lewontin@gmail.com>
Properly declare that the g10 is booting from NAND and define its
correct (larger than on other devices-) boot_pages_size, to prevent
the kernel from constantly falling over missing OOB error correction
for the bootloader.
This patch prevents a constant slew of (bogus) read errors reported
by the kernel and keeping the CPU busy and fixes:
blk_update_request: I/O error, dev mtdblock0, sector 0 op 0x0:(READ) flags 0x80700 phys_seg 4 prio class 0
blk_update_request: I/O error, dev mtdblock0, sector 8 op 0x0:(READ) flags 0x80700 phys_seg 3 prio class 0
blk_update_request: I/O error, dev mtdblock0, sector 16 op 0x0:(READ) flags 0x80700 phys_seg 2 prio class 0
blk_update_request: I/O error, dev mtdblock0, sector 24 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0
blk_update_request: I/O error, dev mtdblock0, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
Buffer I/O error on dev mtdblock0, logical block 0, async page read
blk_update_request: I/O error, dev mtdblock0, sector 32 op 0x0:(READ) flags 0x80700 phys_seg 8 prio class 0
blk_update_request: I/O error, dev mtdblock0, sector 40 op 0x0:(READ) flags 0x80700 phys_seg 7 prio class 0
blk_update_request: I/O error, dev mtdblock0, sector 48 op 0x0:(READ) flags 0x80700 phys_seg 6 prio class 0
blk_update_request: I/O error, dev mtdblock0, sector 56 op 0x0:(READ) flags 0x80700 phys_seg 5 prio class 0
blk_update_request: I/O error, dev mtdblock0, sector 64 op 0x0:(READ) flags 0x80700 phys_seg 4 prio class 0
Buffer I/O error on dev mtdblock0, logical block 1, async page read
Buffer I/O error on dev mtdblock1, logical block 0, async page read
Buffer I/O error on dev mtdblock1, logical block 1, async page read
Buffer I/O error on dev mtdblock2, logical block 0, async page read
Buffer I/O error on dev mtdblock2, logical block 1, async page read
Buffer I/O error on dev mtdblock3, logical block 0, async page read
Buffer I/O error on dev mtdblock3, logical block 0, async page read
Buffer I/O error on dev mtdblock4, logical block 0, async page read
Buffer I/O error on dev mtdblock4, logical block 1, async page read
Suggested-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Each of
- CRYPTO_AEAD2
- CRYPTO_AEAD
- CRYPTO_GF128MUL
- CRYPTO_GHASH
- CRYPTO_HASH2
- CRYPTO_HASH
- CRYPTO_MANAGER2
- CRYPTO_MANAGER
- CRYPTO_NULL2
either directly required for mac80211 crypto support, or directly
selected by such options. Support for the mac80211 crypto was enabled in
the generic config since c7182123b9 ("kernel: make cryptoapi support
needed by mac80211 built-in"). So move the above options from the target
configs to the generic config to make it clear why do we need them.
CC: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Both CLANG_VERSION and LLD_VERISON are autogenerated runtime
configuration options, so add them to the kernel configuration filter
and remove from generic and per-target configs to keep configs clean.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Revert the SDC "CLK_SET_RATE_GATE" changes to the SDC clock regulator
structures.
See https://elinux.org/images/b/b8/Elc2013_Clement.pdf
> if ((clk->flags & CLK_SET_RATE_GATE) && clk->prepare_count) {
>
> For this particular clock, setting its rate is possible only if the
> clock is ungated (not yet prepared)
This fixes the MMC failing to initialize on newer ZyXEL NBG6817
hardware revisions with Kingston MMC. Older revisions should
hopefully be unaffected.
Check MMC hardware details with:
cd /sys/block/mmcblk0/device/ && \
tail -v cid date name manfid fwrev hwrev oemid rev
Known problematic MMC names (broken before this commit):
* M62704 (dated 12/2018) via myself
* M62704 (dated 11/2018) via Drake Stefani
Known unaffected MMC names (already working without this commit):
* S10004 (dated 12/2015) via slh
Without enabling dynamic debugging, this error manifests in the kernel
hardware serial console as the following:
[ 2.746605] mmc0: error -110 whilst initialising MMC card
[…trimmed other messages…]
[ 2.877832] Waiting for root device /dev/mmcblk0p5...
Enabling Linux dynamic kernel debugging provides additional messages.
For guidance, see the Linux kernel documentation:
https://www.kernel.org/doc/html/latest/admin-guide/dynamic-debug-howto.html
First, enable dynamic debugging in OpenWRT's configuration:
1. Run "make menuconfig"
2. Select "Global build settings --->"
3. Select "Kernel build options --->"
4. Enable "Compile the kernel with dynamic printk" via spacebar
5. Save and exit (arrow key to "Exit" until prompted to save, save)
Alternatively, set "CONFIG_KERNEL_DYNAMIC_DEBUG=y" in your .config.
Then, turn on dynamic debugging at boot:
Modify bootargs in
target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8065-nbg6817.dts
to add…
bootargs = "[…existing bootargs…] dyndbg=\"file drivers/mmc/* +p\" dynamic_debug.verbose=1 loglevel=8";
For example:
chosen {
- bootargs = "rootfstype=squashfs,ext4 rootwait noinitrd fstools_ignore_partname=1";
+ bootargs = "rootfstype=squashfs,ext4 rootwait noinitrd fstools_ignore_partname=1 dyndbg=\"file drivers/mmc/* +p\" dynamic_debug.verbose=1 loglevel=8";
append-rootblock = "root=/dev/mmcblk0p";
Then, compile and flash the resulting build. If you are testing
before this commit on newer MMC hardware, be prepared to recover!
NOTE: If you have hardware serial console access, you don't need to
use TFTP recovery to change the active boot partition.
Reboot to working alternative partition via serial console:
1. Connect to hardware serial console
* See https://openwrt.org/toh/zyxel/nbg6817#serial
2. Interrupt boot at "Hit any key to stop autoboot:"
3. Run "ATSE NBG6817"
4. Copy the result (e.g. "001976FE4B04")
* Changes with **every boot** - can't reuse this
5. On your local system, run
"./zyxel-uboot-password-tool.sh <copied value here>"
* Example: "./zyxel-uboot-password-tool.sh 001976FE4B04"
6. Run the command provided by the password tool
* Example: "ATEN 1,910F129B"
* Changes with **every boot** - can't reuse this
7. Run "ATGU"
* You now have full u-boot shell until next boot - unlocking is
not remembered
8. Run either "run boot_mmc" (for booting partition set "FF") or
"run boot_mmc_1" (for booting partition set "01")
* These commands are not affected by dual-boot partition flags
NOTE: This will NOT set the dual-boot partition flag. You'll need to
fix that manually. The "nbg6817-dualboot" script may help:
https://github.com/pkgadd/nbg6817/blob/master/nbg6817-dualboot
zyxel-uboot-password-tool.sh - sourced from
commit 459c8c9ef8:
ror32() {
echo $(( ($1 >> $2) | (($1 << (32 - $2) & (2**32-1)) ) ))
}
v="0x$1"
a="0x${v:2:6}"
b=$(( a + 0x10F0A563))
c=$(( 0x${v:12:14} & 7 ))
p=$(( $(ror32 $b $c) ^ a ))
printf "ATEN 1,%X\n" $p
Kernel serial console log BEFORE commit with dynamic debug enabled:
[…trimmed…]
[ 3.171343] mmci-pl18x 12400000.sdcc: designer ID = 0x51
[ 3.171397] mmci-pl18x 12400000.sdcc: revision = 0x0
[ 3.175811] mmci-pl18x 12400000.sdcc: clocking block at 96000000 Hz
[ 3.181134] mmci-pl18x 12400000.sdcc: No vqmmc regulator found
[ 3.186788] mmci-pl18x 12400000.sdcc: mmc0: PL180 manf 51 rev0 at 0x12400000 irq 41,0 (pio)
[ 3.192902] mmci-pl18x 12400000.sdcc: DMA channels RX dma1chan1, TX dma1chan2
[ 3.215609] mmc0: clock 0Hz busmode 2 powermode 1 cs 0 Vdd 21 width 1 timing 0
[ 3.227532] mmci-pl18x 12400000.sdcc: Initial signal voltage of 3.3v
[ 3.247518] mmc0: clock 52000000Hz busmode 2 powermode 2 cs 0 Vdd 21 width 1 timing 0
[…trimmed…]
[ 3.997725] mmc0: req done (CMD2): -110: 00000000 00000000 00000000 00000000
[ 4.003631] mmci-pl18x 12400000.sdcc: irq0 (data+cmd) 00000000
[ 4.003659] mmc0: error -110 whilst initialising MMC card
[ 4.016481] mmc0: clock 0Hz busmode 2 powermode 0 cs 0 Vdd 0 width 1 timing 0
Notice how the initial clock is 52 MHz, which is incorrect - MMC
requires negotiation to enable higher speeds.
Kernel serial console log AFTER commit with dynamic debug enabled:
[…trimmed…]
[ 3.168996] mmci-pl18x 12400000.sdcc: designer ID = 0x51
[ 3.169051] mmci-pl18x 12400000.sdcc: revision = 0x0
[ 3.173492] mmci-pl18x 12400000.sdcc: clocking block at 96000000 Hz
[ 3.178808] mmci-pl18x 12400000.sdcc: No vqmmc regulator found
[ 3.184702] mmci-pl18x 12400000.sdcc: mmc0: PL180 manf 51 rev0 at 0x12400000 irq 41,0 (pio)
[ 3.190573] mmci-pl18x 12400000.sdcc: DMA channels RX dma1chan1, TX dma1chan2
[ 3.217873] mmc0: clock 0Hz busmode 2 powermode 1 cs 0 Vdd 21 width 1 timing 0
[ 3.229250] mmci-pl18x 12400000.sdcc: Initial signal voltage of 3.3v
[ 3.249111] mmc0: clock 400000Hz busmode 2 powermode 2 cs 0 Vdd 21 width 1 timing 0
[…trimmed…]
[ 4.392652] mmci-pl18x 12400000.sdcc: irq0 (data+cmd) 00000000
[ 4.392785] mmc0: clock 52000000Hz busmode 2 powermode 2 cs 0 Vdd 21 width 1 timing 1
[ 4.406554] mmc0: starting CMD6 arg 03b70201 flags 0000049d
[…trimmed…]
Now, the MMC properly initializes and later switches to high speed.
Thanks to:
* Ansuel for maintaining/help with the IPQ806x platform, kernel code
* slh for additional debugging and suggestions
* dwfreed for confirming newer MMC details, clock frequency
* robimarko for device driver debug printing help, clock debugging
* Drake for testing and confirmation with their own newer NBG6817
...and anyone else I missed!
Signed-off-by: Shane Synan <digitalcircuit36939@gmail.com>
Tested-by: Shane Synan <digitalcircuit36939@gmail.com>
The purpose of this code seems to be to avoid issues caused
by partially overwriting an existing UBI partition, where some
of the erase counters would be reset but not the unmodified
ones. This problem has been solved in a more generic way by
the UBI EOF marker. This ensures that any old PEBs after the
marker are properly initialized. It is therefore unnecessary
to erase the whole partition before flashing a new OpenWrt
factory image.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
The MR42 and MR52 are two similar IPQ806x based devices from the Cisco
Meraki "Cryptid" series.
MR42 main features:
- IPQ8068 1.4GHz
- 512MB RAM
- 128MB NAND
- 2x QCA9992 (2.4 & 5GHz)
- 1x QCA9889 (2.4 & 5GHz)
- 1x AR8033 PHY
- PoE/AC power
MR52 main features:
- IPQ8068 1.4GHz
- 512MB RAM
- 128MB NAND
- 2x QCA9994 (2.4 & 5GHz)
- 1x QCA9889 (2.4 & 5GHz)
- 2x AR8033 PHYs
- PoE/AC power
(MR42 Only) Installation via diagnostic mode:
If you can successfully complete step 1 then you can continue to install
via this method without having to open the device. Otherwise please use
the standard UART method. Please note that when booting via TFTP, some
Ethernet devices, in particular those on laptops, will not connect in
time, resulting in TFTP boot not succeeding. In this instance it is
advised to connect via a switch.
1. Hold down reset at power on and keep holding, after around 10 seconds
if the orange LED changes behaviour to begin flashing, proceed to
release reset, then press reset two times. Ensure that the LED has
turned blue. Note that flashing will occur on some devices, but it
will not be possible to change the LED colour using the reset button.
In this case it will still be possible to continue with this install
method.
2. Set your IP to 192.168.1.250. Set up a TFTP server serving
mr42_u-boot.mbn and
openwrt-ipq806x-generic-meraki_mr42-initramfs-fit-uImage.itb, obtained
from [1].
3. Use telnet and connect to 192.168.1.1. Run the following commands to
install u-boot. Note that all these commands are critical, an error
will likely render the device unusable.
Option 3.1:
If you are sure you have set up the TFTP server correctly you can
run this script on the device. This will download and flash the
u-boot image immediately:
`/etc/update_uboot.sh 192.168.1.250 mr42_u-boot.mbn`
Once completed successfully, power off the device.
Option 3.2:
If you are unsure the TFTP server is correctly set up you can
obtain the image and flash manually:
3.2.1. `cd /tmp`
3.2.2. `tftp-hpa 192.168.1.250 -m binary -c get mr42_u-boot.mbn`
3.2.3. Confirm file has downloaded correctly by comparing the
md5sum:
`md5sum mr42_u-boot.mbn`
3.2.4. The following are the required commands to write the image.
`echo 1 > /sys/devices/platform/msm_nand/boot_layout
mtd erase /dev/mtd1
nandwrite -pam /dev/mtd1 mr42_u-boot.mbn
echo 0 > /sys/devices/platform/msm_nand/boot_layout`
Important: You must observe the output of the `nandwrite`
command. Look for the following to verify writing is occurring:
`Writing data to block 0 at offset 0x0
Writing data to block 1 at offset 0x20000
Writing data to block 2 at offset 0x40000`
If you do not see this then do not power off the device. Check
your previous commands and that mr42_u-boot.mbn was downloaded
correctly. Once you are sure the image has been written you
can proceed to power off the device.
4. Hold the reset button and power on the device. This will immediately
begin downloading the appropriate initramfs image and boot into it.
Note: If the device does not download the initramfs, this is likely
due to the interface not being brought up in time. Changing Ethernet
source to a router or switch will likely resolve this. You can also
try manually setting the link speed to 10Mb/s Half-Duplex.
5. Once a solid white LED is displayed on the device, continue to the
UART installation method, step 6.
Standard installation via UART - MR42 & MR52
1. Disassemble the device and connect a UART header. The header pinout
is as follows:
1 - 3.3v
2 - TXD
3 - RXD
4 - GND
Important: You should only connect TXD, RXD and GND. Connecting
3.3v may damage the device.
2. Set your IP to 192.168.1.250. Set up a TFTP server serving
openwrt-ipq806x-generic-meraki_(mr42|mr52)-initramfs-fit-uImage.itb.
Separately obtain the respective sysupgrade image.
3. Run the following commands, preferably from a Linux host. The
mentioned files, including ubootwrite.py and u-boot images, can be
obtained from [1].
`python ubootwrite.py --write=(mr42|mr52)_u-boot.bin`
The default for "--serial" option is /dev/ttyUSB0.
4. Power on the device. The ubootwrite script will upload the image to
the device and launch it. The second stage u-boot will in turn load
the initramfs image by TFTP, provided the TFTP server is running
correctly. This process will take about 13 minutes. Once a solid
white LED is displayed, the image has successfully finished
loading. Note: If the image does not load via TFTP, try again with
the Ethernet link to 10Mb/s Half-Duplex.
5. (MR42 only) Do not connect over the network. Instead connect over
the UART using minicom or similar tool. To replace u-boot with
the network enabled version, please run the following commands.
Note that in the provided initramfs images, the u-boot.mbn file
is located in /root:
If you have not used the provided initramfs, you must ensure you
are using an image with "boot_layout" ECC configuration enabled in
the Kernel. This will be version 5.10 or higher. If you do not do
this correctly the device will be bricked.
`insmod mtd-rw i_want_a_brick=1
mtd erase /dev/mtd8
nandwrite -pam /dev/mtd8 /root/mr42_u-boot.mbn`
After running nandwrite, ensure you observe the following output:
`Writing data to block 0 at offset 0x0
Writing data to block 1 at offset 0x20000
Writing data to block 2 at offset 0x40000`
6. (Optional) If you have no further use for the Meraki OS, you can
remove all other UBI volumes on ubi0 (mtd11), including diagnostic1,
part.old, storage and part.safe. You must not remove the ubi1 ART
partition (mtd12).
`for i in diagnostic1 part.old storage part.safe ; do
ubirmvol /dev/ubi0 -N $i
done`
7. Proceed to flash the sysupgrade image via luci, or else download or
scp the image to /tmp and use the sysupgrade command.
[1] The mentioned images and ubootwrite.py script can be found in this repo:
https://github.com/clayface/openwrt-cryptid
[2] The modified u-boot sources for the MR42 and MR52 are available:
https://github.com/clayface/U-boot-MR52-20200629
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
Add backports of the following patches:
"net: stmmac: explicitly deassert GMAC_AHB_RESET" and
"ARM: dts: qcom: add ahb reset to ipq806x-gmac"
Required for Meraki MR42/MR52.
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
Rather than having separate patches for each GSBI node added, this patch
consolidates the existing GSBI1 patch into
083-ipq8064-dtsi-additions.patch. In addition, GSBI6 and GSBI7 I2C nodes,
required for the MR42 and MR52 respectively, are added.
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
Currently, we are overriding the bootloader provided MAC-s as the ethernet
aliases are reversed so MAC-s were fixed up in userspace.
There is no need to do that as we can just fix the aliases instead and get
rid of MAC setting via userspace helper.
Fixes: 59f0a0f ("ipq806x: add Edgecore ECW5410 support")
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
ECW5410 has 2 QCA9984 cards, one per PCI controller.
They are located at PCI adresses 0001:01:00.0 and 0002:01:00.0.
Currently, pre-cal is not provided for 0001:01:00.0 at all,but for
0000:01:00.0 which is incorrect and causes the ath10k driver to not
be able to fetch the BMI ID and use that to fetch the proper BDF but
rather fail with:
[ 12.029708] ath10k 5.10 driver, optimized for CT firmware, probing pci device: 0x46.
[ 12.031816] ath10k_pci 0001:01:00.0: enabling device (0140 -> 0142)
[ 12.037660] ath10k_pci 0001:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
[ 13.173898] ath10k_pci 0001:01:00.0: qca9984/qca9994 hw1.0 target 0x01000000 chip_id 0x00000000 sub 168c:cafe
[ 13.174015] ath10k_pci 0001:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
[ 13.189304] ath10k_pci 0001:01:00.0: firmware ver 10.4b-ct-9984-fW-13-5ae337bb1 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc35
[ 15.492322] ath10k_pci 0001:01:00.0: failed to fetch board data for bus=pci,vendor=168c,device=0046,subsystem-vendor=168c,subsystem-device=cafe,variant=Edgecore-ECW541 from ath10k/QCA9984/hw1.0/board-2.bin
[ 15.543883] ath10k_pci 0001:01:00.0: failed to fetch board-2.bin or board.bin from ath10k/QCA9984/hw1.0
[ 15.543920] ath10k_pci 0001:01:00.0: failed to fetch board file: -12
[ 15.552281] ath10k_pci 0001:01:00.0: could not probe fw (-12)
So, provide the pre-cal for the actual PCI card and not the non-existent
one.
Fixes: 59f0a0f ("ipq806x: add Edgecore ECW5410 support")
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
It looks like this is a leftover before there was a proper MDIO driver.
Since both PHY-s are connected to the HW MDIO bus there is no reason for
this to exist anymore, especially since it uses the same pins as the HW
controller and has the pinmux for the set to "MDIO" so this worked by
pure luck as GPIO MDIO would probe first and override the HW driver.
Move the GMAC3 to simply use the same MDIO bus phandle.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
After the ath10k_patch_mac lines have been removed, a lot of blocks
can be consolidated.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The out-of-tree qcom-smem patches traditionally displayed mtd partition names
in upper case, starting with the new mainline qcom-smem support in kernel v5.10,
it switched to normalizing the partition names to lower case.
While both 5.4 and 5.10 were supported in the target, we carried a workaround
to support both of them. Since the target has dropped 5.4 recently, those
can be removed now.
Ref:
2db9dded0a ("ipq806x: nbg6817: case-insensitive qcom-smem partitions")
435dc2e77e ("ipq806x: ecw5410: case-insensitive qcom-smem partitions")
f70e11cd97 ("ipq806x: g10: case-insensitive qcom-smem partitions")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Use nvmem framework for supported mac-address stored
in nvmem cells and drop mac patch function for hotplug
script for supported devices.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
[rebase, move to correct node for d7800, include xr500]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Deleted (upstreamed):
bcm27xx/patches-5.10/950-0145-xhci-add-quirk-for-host-controllers-that-don-t-updat.patch [1]
Manually rebased:
bcm27xx/patches-5.10/950-0355-xhci-quirks-add-link-TRB-quirk-for-VL805.patch
bcm53xx/patches-5.10/180-usb-xhci-add-support-for-performing-fake-doorbell.patch
Note: although automatically rebaseable, the last patch has been edited to avoid
conflicting bit definitions.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=linux-5.10.y&id=b6f32897af190d4716412e156ee0abcc16e4f1e5
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
This adds support for the Netgear Nighthawk Pro Gaming XR500.
It is the successor to the Netgear Nighthawk R7800 and shares almost
identical hardware to that device.
The stock firmware is a heavily modified version of OpenWRT.
Specifications:
SoC: Qualcomm Atheros IPQ8065
RAM: 512 MB
Storage: 256 MiB NAND Flash
Wireless: 2x Qualcomm Atheros QCA9984
Ethernet: 2x 1000/100/10 dedicated interfaces
Switch: 5x 1000/100/10 external ports
USB: 2x 3.0 ports
More information:
Manufacturer page: https://www.netgear.com/gaming/xr500/
Almost identical to Netgear R7800
Differences (r7800 > xr500):
Flash: 128MiB > 256MiB
Removed esata
swapped leds:
usb1 (gpio 7 > 8)
usb2 (gpio 8 > 26)
guest/esata (gpio 26 > 7)
MAC addresses:
On the OEM firmware, the mac addresses are:
WAN: *:50 art 0x6
LAN: *:4f art 0x0 (label)
2G: *:4f art 0x0
5G: *:51 art 0xc
Installation:
Install via Web Interface (preferred):
Utilize openwrt-ipq806x-netgear_xr500-squashfs-factory.img
Install via TFTP recovery:
1.Turn off the power, push and hold the reset button (in a hole on
backside) with a pin
2.Turn on the power and wait till power led starts flashing white
(after it first flashes orange for a while)
3.Release the reset button and tftp the factory img in binary mode.
The power led will stop flashing if you succeeded in transferring
the image, and the router reboots rather quickly with the new
firmware.
4.Try to ping the router (ping 192.168.1.1). If does not respond,
then tftp will not work either.
Uploading the firmware image with a TFTP client
$ tftp 192.168.1.1
bin
put openwrt-ipq806x-netgear_xr500-squashfs-factory.img
Note:
The end of the last partition is at 0xee00000. This was chosen
by the initial author, but nobody was able to tell why this
particular arbitrary size was chosen. Since it's not leaving
too much empty space and it's the only issue left, let's just
keep it for now.
Based on work by Adam Hnat <adamhnat@gmail.com>
ref: https://github.com/openwrt/openwrt/pull/3215
Signed-off-by: Peter Geis <pgwipeout@gmail.com>
[squash commits, move common LEDs to DTSI, remove SPDX on old
files, minor whitespace cleanup, commit message facelift,
add MAC address overview, add Notes, fix MAC addresses,
use generic name for partition nodes in DTS]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Move kernel version to 5.10 as has been tested by many users
with positive feedback.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
[Tested on: ipq8064/g10; ipq8065/nbg6817]
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
The default value for CONFIG_RCU_CPU_STALL_TIMEOUT was changed from 60
seconds to 21 seconds in 2012 in the upstream kernel. Some targets
already use 21 seconds.
This patch changes the default value in the generic configuration to 21
seconds and removes the target specific configuration options.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Rui Salvaterra <rsalvaterra@gmail.com>
The partitions that have compatible property set are skipped by mtd if
they are not contained inside a partitions node and this breaks
fetching MAC address from "default-mac" partition.
Fix this by defining all the partitions inside partitions node with
compatible = "fixed-partitions" as nvmem requires the standard
partitions scheme to work correctly.
Fixes: FS#3945
Fixes: cd36d71655 ("ipq806x/dts: Add Archer C2600 DTS")
Fixes: 0458a8993c ("ipq806x: convert mtd-mac-address to nvmem
implementation")
Signed-off-by: Filip Matijević <filip.matijevic.pz@gmail.com>
Reviewed-by: Ansuel Smith <ansuelsmth@gmail.com>
[adjust commit title/message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
CONFIG_RCU_{NEED_SEGCBLIST,STALL_COMMON} are set basically everywhere. Move them
to the generic kconfigs. And resort the generic kconfigs while at it.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
The problem has been fixed in f47cb405ca ("ipq806x: fix pci broken
on bootm command"), now the pcie part can be written in the usual way.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Reviewed-by: Ansuel Smith <ansuelsmth@gmail.com>
The partition name in the device dts is '0:ART'.
Be independent to prevent this part from becoming
incorrect once the kernel v5.4 gone.
Fixes: da8428d277 ("ipq806x: add support for Askey RT4230W REV6")
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Rearrange all voltage triplets for "opp_table0" to match the
specifications. "opp-microvolt" and "opp-microvolt-<name>" triplets
are in order of <target min max>, and NOT <min target max>.
Previously, the CPU would *always* spend its time at the "minimum"
voltage, ignoring the actual intended target. This is a regression
from previous behavior.
On an NBG6817 with a Qualcomm CPU of PVS bin #2...
(see &opp_table0 -> opp-1725000000 -> opp-microvolt-speed0-pvs2-v0)
* Before:
/usr/bin/tail -n +1 /sys/kernel/debug/opp/cpu0/opp\:1725000000/supply-0/u_volt_*
==> /sys/kernel/debug/opp/cpu0/opp:1725000000/supply-0/u_volt_max <==
1260000
==> /sys/kernel/debug/opp/cpu0/opp:1725000000/supply-0/u_volt_min <==
1200000
==> /sys/kernel/debug/opp/cpu0/opp:1725000000/supply-0/u_volt_target <==
1140000
* After:
/usr/bin/tail -n +1 /sys/kernel/debug/opp/cpu0/opp\:1725000000/supply-0/u_volt_*
==> /sys/kernel/debug/opp/cpu0/opp:1725000000/supply-0/u_volt_max <==
1260000
==> /sys/kernel/debug/opp/cpu0/opp:1725000000/supply-0/u_volt_min <==
1140000
==> /sys/kernel/debug/opp/cpu0/opp:1725000000/supply-0/u_volt_target <==
1200000
To check voltages and frequencies at run time, use...
/bin/cat /sys/kernel/debug/regulator/regulator_summary &&
/bin/cat /sys/kernel/debug/clk/clk_summary | grep "hfpll"
See
https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/tree/Documentation/devicetree/bindings/opp/opp.txt?h=v5.4.142#n91
Fixes: 1e25423be8 ("ipq806x: refresh dtsi patches")
Signed-off-by: Shane Synan <digitalcircuit36939@gmail.com>
Reviewed-by: Ansuel Smith <ansuelsmth@gmail.com>
[commit message style cleanup, another kernel refresh]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Define nvmem-cells and convert mtd-mac-address to nvmem implementation.
The conversion is done with an automated script.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Rework patch 681-NET-add-mtd-mac-address-support to implement
only the function to read the mac-address from mtd.
Generalize mtd-mac-address-increment function so it can be applied
to any source of of_get_mac_address.
Rename any mtd-mac-address-increment to mac-address-increment.
Rename any mtd-mac-address-increment-byte to mac-address-increment-byte.
This should make simplify the conversion of target to nvmem implementation.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
sysupgrade metadata is not flashed to the device, so check-size
should be called _before_ adding metadata to the image.
While at it, do some obvious wrapping improvements.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Paul Spooren <mail@aparcar.org>
2 small fix for the dedicated cpufreq driver:
- Fix index wrongly used as the current cpu
- Exit early if a bad freq is detected. In the current state the freq
is applied anyway even with invalid state.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
With the new implementation of the dedicated cpufreq driver,
the 1.4 Ghz was only dropped and not added to the ipq8065 SoC.
Fix this to improve performance.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
The new cpufreq dedicated driver changed the node structure
on how the cache should be defined in the dts. The 5.4 dtsi addition
patch has not been updated to follow the new implementation.
Fix this to restore correct cache scaling and restore any performance
regression.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
* With kernel 5.4.128, ran: make kernel_menuconfig CONFIG_TARGET=generic
* Manually added back CONFIG_LEDS_TRIGGER_DISK=y so as not to revert
f93fcf8923 ("ipq806x: enable disk-activity LED trigger")
Signed-off-by: John Audia <graysky@archlinux.us>
[minor commit title/message adjustments]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
LAN port 4 was swapped with the WAN port and the remaining three LAN
ports were numbered in reverse order from their labels on the case.
Fixes: 1a775a4fd0 ("ipq806x: add support for TP-Link Talon AD7200")
Signed-off-by: Alex Henrie <alexhenrie24@gmail.com>
Many people appear to use an unneeded "+" prefix for the increment
when calculating a MAC address with macaddr_add. Since this is not
required and used inconsistently [*], just remove it.
[*] As a funny side-fact, copy-pasting has led to almost all
hotplug.d files using the "+", while nearly all of the
02_network files are not using it.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This adds support for the Askey RT4230W REV6
(Branded by Spectrum/Charter as RAC2V1K)
At this time, there's no way to reinstall the stock firmware so don't install
this on a router that's being rented.
Specifications:
Qualcomm IPQ8065
1 GB of RAM (DDR3)
512 MB Flash (NAND)
2x Wave 2 WiFi cards (QCA9984)
5x 10/100/1000 Mbps Ethernet (Switch: QCA8337)
1x LED (Controlled by a microcontroller that switches it between red and
blue with different patterns)
1x USB 3.0 Type-A
12V DC Power Input
UART header on PCB - pinout from top to bottom is RX, TX, GND, 5V
Port settings are 115200n8
More information: https://forum.openwrt.org/t/askey-rac2v1k-support/15830https://deviwiki.com/wiki/Askey_RAC2V1K
To check what revision your router is, restore one of these config backups
through the stock firmware to get ssh access then run
"cat /proc/device-tree/model".
https://forum.openwrt.org/t/askey-rac2v1k-support/15830/17
The revision number on the board doesn't seem to be very consistent so that's
why this is needed. You can also run printenv in the uboot console and if
machid is set to 177d, that means your router is rev6.
Note: Don't install this if the router is being rented from an ISP. The defined
partition layout is different from the OEM one and even if you changed the
layout to match, backing up and restoring the OEM firmware breaks /overlay so
nothing will save and the router will likely enter a bootloop.
How to install:
Method 1: Install without opening the case using SSH and tftp
You'll need:
RAC2V1K-SSH.zip:
https://github.com/lmore377/openwrt-rt4230w/blob/master/RAC2V1K-SSH.zip
initramfs and sysupgrade images
Connect to one of the router's LAN ports
Download the RAC2V1K-SSH.zip file and restore the config file that
corresponds to your router's firmware (If you're firmware is newer than what's
in the zip file, just restore the 1.1.16 file)
After a reboot, you should be able to ssh into the router with username:
"4230w" and password: "linuxbox" or "admin". Run the following commannds
fw_setenv ipaddr 10.42.0.10 #IP of router, can be anything as long as
it's in the same subnet as the server
fw_setenv serverip 10.42.0.1# #IP of tftp server that's set up in next
steps
fw_setenv bootdelay 8
fw_setenv bootcmd "tftpboot initramfs.bin; bootm; bootipq"
Don't reboot the router yet.
Install and set up a tftp server on your computer
Set a static ip on the ethernet interface of your computer (use this for
serverip in the above commands)
Rename the initramfs image to initramfs.bin, and host it with the tftp
server
Reboot the router. If you set up everything right, the router led should
switch over to a slow blue glow which means openwrt is booted. If for some
reason the file doesn't get loaded into ram properly, it should still boot to
the OEM firmware.
After openwrt boots, ssh into it and run these commands:
fw_setenv bootcmd "setenv mtdids nand0=nand0 && setenv mtdparts
mtdparts=nand0:0x1A000000@0x2400000(firmware) && ubi part firmware && ubi
read 0x44000000 kernel 0x6e0000 && bootm"
fw_setenv bootdelay 2
After openwrt boots up, figure out a way to get the sysupgrade file onto it
(scp, custom build with usb kernel module included, wget, etc.) then flash it
with sysupgrade. After it finishes flashing, it should reboot, the light should
start flashing blue, then when the light starts "breathing" blue that means
openwrt is booted.
Method 2: Install with serial access (Do this if something fails and you can't
boot after using method 1)
You'll need:
initramfs and sysupgrade images
Serial access:
https://openwrt.org/inbox/toh/askey/askey_rt4230w_rev6#opening_the_case
Install and set up a tftp server
Set a static ip on the ethernet interface of your computer
Download the initramfs image, rename it to initramfs.bin, and host it with
the tftp server
Connect the wan port of the router to your computer
Interrupt U-Boot and run these commands:
setenv serverip 10.42.0.1 (You can use whatever ip you set for the computer)
setenv ipaddr 10.42.0.10 (Can be any ip as long as it's in the same subnet)
setenv bootcmd "setenv mtdids nand0=nand0 &&
set mtdparts mtdparts=nand0:0x1A000000@0x2400000(firmware) && ubi part firmware
&& ubi read 0x44000000 kernel 0x6e0000 && bootm"
saveenv
tftpboot initramfs.bin
bootm
After openwrt boots up, figure out a way to get the sysupgrade file onto it
(scp, custom build with usb kernel module included, wget, etc.) then flash it
with sysupgrade. After it finishes flashing, it should reboot, the light should
start flashing blue, then when the light starts "breathing" blue that means
openwrt is booted.
Signed-off-by: Lauro Moreno <lmore377@gmail.com>
[add entry in 5.10 patch, fix whitespace issues]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Backport a pending patch already reviewed that fix some warning about tsens debugs already registered.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
With some talk with the ARM maintainer, it was notice that enlarging the limit
to the current value is VERY wrong and clash with other memory.
A better solution would be to reduce the IO space from 1MB to 64K as probably
it's a long lasting typo and even x86 arch doesn't have a IO space that big.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Removed upstreamed:
generic/pending-5.4/770-02-net-ethernet-mtk_eth_soc-fix-rx-vlan-offload.patch
All other patches automatically rebased.
Build system: x86_64
Build-tested: ipq806x/R7800
Note that since I rebased the previous commit, I removed my Run-tested line
although I confirm building the image successfully.
Signed-off-by: John Audia <graysky@archlinux.us>
Fixes following error while executing the init script on the buildhost:
Enabling boot
./etc/init.d/bootcount: line 5: /lib/upgrade/asrock.sh: No such file or directory
Enabling bootcount
While at it fix following shellcheck issue:
base-files/etc/init.d/bootcount line 11:
if [ $? -eq 0 ]; then
^-- SC2181: Check exit code directly with e.g. 'if mycmd;', not indirectly with $?.
Cc: Ansuel Smith <ansuelsmth@gmail.com>
Cc: Pawel Dembicki <paweldembicki@gmail.com>
Cc: Christian Lamparter <chunkeey@gmail.com>
Fixes: 98b86296e6 ("ipq806x: add support for ASRock G10")
References: https://gitlab.com/ynezz/openwrt/-/jobs/1243290743#L1444
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Kernel 5.10 support for ipq806x was added at the same time that these
patches were developed for kernel 5.4. This carries the patches forward
to kernel 5.10.
fa731838c5 ipq806x: dwmac: clear forced speed during probe
75ca641f1b ipq806x: Add "snps,dwmac" to all gmac compatible=
d62825dd77 ipq806x: dwmac: set forced speed when using fixed-link
Signed-off-by: Mark Mentovai <mark@moxienet.com>
Run-tested: ipq806x/ubnt,unifi-ac-hd
Cc: Ansuel Smith <ansuelsmth@gmail.com>
d53be2a2e9 migrated 0069-arm-boot-add-dts-files.patch from patches-5.4
to patches-5.10, but a subsequent patch in that set, 1e25423be8,
erroneously removed several devices:
ipq8062/nec,wg2600hp3 from 3bb1618573
ipq8064/asrock,g10 from 98b86296e6
ipq8064/ubnt,unifi-ac-hd from 4e46beb313
Signed-off-by: Mark Mentovai <mark@moxienet.com>
Run-tested: ipq806x/ubnt,unifi-ac-hd
Cc: Ansuel Smith <ansuelsmth@gmail.com>
The out-of-tree qcom-smem patches traditionally displayed mtd partition names
in upper case, starting with the new mainline qcom-smem support in kernel v5.10,
it switches to normalizing the partition names to lower case.
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
The out-of-tree qcom-smem patches traditionally displayed mtd partition names
in upper case, starting with the new mainline qcom-smem support in kernel v5.10,
it switches to normalizing the partition names to lower case.
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
The out-of-tree qcom-smem patches traditionally displayed mtd partition names
in upper case, starting with the new mainline qcom-smem support in kernel v5.10,
it switches to normalizing the partition names to lower case.
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
fa731838c5 cleared the forced speed in the QSGMII PCS_ALL_CH_CTL
register during probe, but this is only correct for GMACs that are not
configured with fixed-link. This prevented GMACs configured with both
phy-mode = "sgmii" and fixed-link from working properly, as discussed at
https://github.com/openwrt/openwrt/pull/3954#issuecomment-834625090 and
the comments that follow. Notably, this prevented all communication
between gmac2 and the switch on the Netgear R7800.
The correct behavior is to set the QSGMII PCS_ALL_CH_CTL register by
considering the gmac's fixed-link child, setting the speed as directed by
fixed-link if present, and otherwise clearing it as was done previously.
Fixes: fa731838c5 ("ipq806x: dwmac: clear forced speed during probe")
Signed-off-by: Mark Mentovai <mark@moxienet.com>
Tested-by: Hannu Nyman <hannu.nyman@iki.fi>
Run-tested: ipq806x/ubnt,unifi-ac-hd, ipq806x/netgear,r7800
Cc: Petr Štetiar <ynezz@true.cz>
Cc: Ansuel Smith <ansuelsmth@gmail.com>
Tested-by: Ansuel Smith <ansuelsmth@gmail.com>
wakeup-source is required for gpio keys to fix error
genirq: irq_chip msmgpio did not update eff. affinity mask
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
- Add new tsens node
- Add new cpufreq required nodes
- Drop arm cpuidle compatible
- Fix duplicate node set upstream
- Add voltage tolerance value for cpu opp
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
ipq806x have different ecc configuration for boot partition and rootfs partition. Add support for this to fix IO error on mtd block scan.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
The spm driver now has dedicated support for krait cpu idle state. We don't need to add generic arm cpuidle support for qcom.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Patch 0030 wrongly disables gsbi1 instead of gsbi4.
Fix the wrong patch and also include other fix from the original qsdk source.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Various report and data show that the freq 384000 is too low and cause some
extra latency to the entire system. OEM qsdk code also set the min frequency
for this target to 800 mhz.
Also some user notice some instability with this idle frequency, solved by
setting the min frequency to 600mhz. Fix all these kind of problem by
introducing a boot init.d script that set the min frequency to 600mhz and set
the ondemand governor to be more aggressive. The script set these value only if
the ondemand governor is detected. 384 mhz freq is still available and user can
decide to restore the old behavior by disabling this script.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
This was introduced to gmac2 and gmac3 in 57ea767a53 without fanfare.
There's no indication of why it was added to those devices, but not to
gmac0 or gmac1. It was probably an unintentional omission. It should be
present on all four gmac devices.
This property is considered by
drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c
stmmac_probe_config_dt.
Signed-off-by: Mark Mentovai <mark@moxienet.com>
Build-tested: ipq806x/ubnt,unifi-ac-hd
Run-tested: ipq806x/ubnt,unifi-ac-hd
The Ubiquiti UniFi AC HD (UAP-AC-HD, UAP301) has two Ethernet ports,
labeled MAIN and SECONDARY, connected to gmac2 and gmac1, respectively.
The standard probe order results in gmac1/SECONDARY being eth0 and
gmac2/MAIN being eth1. This does not match the stock firmware, is
contrary to user expectation, causes the wrong (high) MAC address to be
used in a bridged configuration (the default for this device), and makes
the gmac2/MAIN port unusable in the preinit environment (such as for
failsafe). Until a recent patch, gmac1/SECONDARY (eth0) was not even
usable.
This reorders the ports so that gmac2/MAIN is eth0, and the now-working
gmac1/SECONDARY is eth1. eth0 has the low MAC address and eth1 has the
high; when bridged, the bridge takes on the correct low MAC address.
This matches the stock firmware. The MAIN port is usable for failsafe
during preinit.
This device does not have a switch on board, so there's no possibility
to remap ports via switch configuration. "ip link set $interface name"
is used instead, during preinit before networking is configured.
Signed-off-by: Mark Mentovai <mark@moxienet.com>
Build-tested: ipq806x/ubnt,unifi-ac-hd
Run-tested: ipq806x/ubnt,unifi-ac-hd
Unlike many ipq806x devices, Ubiquiti UniFi AC HD (UAP-AC-HD, UAP301)
has no switch on board. Its two Ethernet ports are connected to Atheros
AR8033 PHYs. It is not appropriate to use fixed-link in this
configuration. Instead, configure the correct PHYs in the device tree
configuration to allow the at803x driver to load.
Signed-off-by: Mark Mentovai <mark@moxienet.com>
Build-tested: ipq806x/ubnt,unifi-ac-hd
Run-tested: ipq806x/ubnt,unifi-ac-hd
On a Ubiquiti UniFi AC HD (ubnt,unifi-ac-hd, UAP-AC-HD, UAP301), a
forced speed on gmac1 is set in the QSGMII PCS_ALL_CH_CTL register,
presumably by the bootloader (4.3.28), preventing the interface from
being usable. The QSDK NSS GMAC driver takes care to clear the forced
speed in nss_gmac_qsgmii_dev_init
(https://source.codeaurora.org/quic/qsdk/oss/lklm/nss-gmac/tree/ipq806x/nss_gmac_init.c?h=nss
at d5bb14925861).
gmac1 is connected to the port on the device labeled SECONDARY, and is
currently eth0 but will be switched to eth1 by a subsequent patch. By
clearing the QSGMII PCS forced speed during dwmac initialization when
SGMII is in use, this port becomes usable.
This patch is upstreamable, and will be sent upstream after successful
testing in OpenWrt.
Signed-off-by: Mark Mentovai <mark@moxienet.com>
Build-tested: ipq806x/ubnt,unifi-ac-hd
Run-tested: ipq806x/ubnt,unifi-ac-hd
Some targets select HZ=100, others HZ=250. There's no reason to select a higher
timer frequency (and 100 Hz are available in every architecture), so change all
targets to 100 Hz.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
For the targets which enable ubifs, these symbols are already part of the
generic kconfigs. Drop them from the target kconfigs.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Ran update_kernel.sh in a fresh clone without any existing toolchains.
Manually rebased:
pending-5.4/611-netfilter_match_bypass_default_table.patch
The upstream change affecting this patch is the revert of an earlier
kernel commit. Therefore, we just revert our corresponding changes
in [1].
Build system: x86_64
Build-tested: ipq806x/R7800
[1] 9b1b89229f ("kernel: bump 5.4 to 5.4.86")
Signed-off-by: John Audia <graysky@archlinux.us>
[adjust manually rebased patch, add explanation]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
1. Use upstream accepted NVMEM patches
2. Minor fix for BCM4908 partitioning
3. Support for Linksys firmware partitions on Northstar
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
ZyXEL NBG6817 comes with an eMMC which contains a GPT partition named
'rootfs_data'. This currently confuses fstools and makes it pick that
(not suitable) partition.
Use the newly introduced fstools_ignore_partname=1 kernel cmdline
parameter to have fstools ignore that partition.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The bootloader of many ipq806x boards seems to require the config node
of the FIT image to be 'config@1' (or a secific different value).
This requirement used to be implicitely satisfied because OpenWrt used
to also call the configuration node inside a FIT image 'config@1'.
However, as recent U-Boot now prohibits the use of the '@' symbol as
part of node names, this was changed by
commit 5ec60cbe9d ("scripts: mkits.sh: replace @ with - in nodes")
Explicitely restore the default name of the configuration node to
'config@1' on ipq806x.
(ipq807x is unaffected as DEVICE_DTS_CONFIG default is set
"config@hk01" in target/linux/ipq807x/image/Makefile)
Reported-by: Chen Minqiang <ptpt52@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
So far, board.d files were having execute bit set and contained a
shebang. However, they are just sourced in board_detect, with an
apparantly unnecessary check for execute permission beforehand.
Replace this check by one for existance and make the board.d files
"normal" files, as would be expected in /etc anyway.
Note:
This removes an apparantly unused '#!/bin/sh /etc/rc.common' in
target/linux/bcm47xx/base-files/etc/board.d/01_network
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
5.4.102 backported a lot of stuff that our WireGuard backport already
did, in addition to other patches we had, so those patches were
removed from that part of the series. In the process other patches were
refreshed or reworked to account for upstream changes.
This commit involved `update_kernel.sh -v -u 5.4`.
Cc: John Audia <graysky@archlinux.us>
Cc: David Bauer <mail@david-bauer.net>
Cc: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
This adds the latest version of ofpart commit. It hopefully
1. Doesn't break compilation
2. Doesn't break partitioning
(this time).
It's required to implement fixed partitioning with some quirks. It's
required by bcm53xx, bcm4908, kirkwood, lantiq and mvebu.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
The variables KERNEL_INITRAMFS_PREFIX and KERNEL_PREFIX are already
defined in include/image.mk and don't have to be redefined in the
target Makefiles.
Signed-off-by: Paul Spooren <mail@aparcar.org>
[also cover imx6]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This replaces a full-text BSD clause by the corresponding SPDX
identifier.
This should make it easier to identify the license both by humans
and machines.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
On a platform with many very different devices, like found on ipq806x,
the generic profile seems like a remnant of the past that does not
have a real use anymore.
Remove it to have one thing less to maintain.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Paul Spooren <mail@aparcar.org>
The majority of our targets provide a default value for the variable
SUPPORTED_DEVICES, which is used in images to check against the
compatible on a running device:
SUPPORTED_DEVICES := $(subst _,$(comma),$(1))
At the moment, this is implemented in the Device/Default block of
the individual targets or even subtargets. However, since we
standardized device names and compatible in the recent past, almost
all targets are following the same scheme now:
device/image name: vendor_model
compatible: vendor,model
The equal redundant definitions are a symptom of this process.
Consequently, this patch moves the definition to image.mk making it
a global default. For the few targets not using the scheme above,
SUPPORTED_DEVICES will be defined to a different value in
Device/Default anyway, overwriting the default. In other words:
This change is supposed to be cosmetic.
This can be used as a global measure to get the current compatible
with: $(firstword $(SUPPORTED_DEVICES))
(Though this is not precisely an achievement of this commit.)
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This fixes a typo in the previously committed partition map that led to
the extension of the read-only mtd partition "SSD" into the following
partitions.
Fixes: 4e46beb313 ("ipq806x: add support for Ubiquiti UniFi AC HD")
Signed-off-by: Jan Alexander <jan@nalx.net>
Hardware
--------
SoC: Qualcomm IPQ8064
RAM: 512MB DDR3
Flash: 256MB NAND (Micron MT29F2G08ABBEAH4)
32MB SPI-NOR (Macronix MX25U25635F)
WLAN: Qualcomm Atheros QCA9994 4T4R b/g/n
Qualcomm Atheros QCA9994 4T4R a/n/ac
ETH: eth0 - SECONDARY (Atheros AR8033)
eth1 - MAIN (Atheros AR8033)
USB: USB-C
LED: Dome (white / blue)
BTN: Reset
Installation
------------
Copy the OpenWrt sysupgrade image to the /tmp directory of the device
using scp. Default IP address is 192.168.1.20 and default username and
password are "ubnt".
SSH to the device and write the bootselect flag to ensure it is booting
from the mtd partition the OpenWrt image will be written to. Verify the
output device below matches mtd partition "bootselect" using /proc/mtd.
> dd if=/dev/zero bs=1 count=1 seek=7 conv=notrunc of=/dev/mtd11
Write the OpenWrt sysupgrade image to the mtd partition labeled
"kernel0". Also verify the used partition device using /proc/mtd.
> dd if=/tmp/sysupgrade.bin of=/dev/mtdblock12
Reboot the device.
Back to stock
-------------
Use the TFTP recovery procedure with the Ubiquiti firmware image to
restore the vendor firmware.
Signed-off-by: Jan Alexander <jan@nalx.net>
Strictly, an SPDX identifier requires a space between the comment
marker and the identifier itself. This has been addressed in
b69c21738e ("treewide: add space before SPDX identifier"), but
some new malformatted identifiers were merged recently.
This could have been prevented by using checkpatch.pl earlier.
Fixes: 1a775a4fd0 ("ipq806x: add support for TP-Link Talon AD7200")
Fixes: 8ddaeaf642 ("ipq806x: create DTSI for TP-Link AD7200 and C2600")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The TP-Link AD7200 appears with and without the "Talon" model name
prefix. Let's use both variants for 'make menuconfig' so everybody
can locate the device.
Concerning the revision, the TP-Link page lists v1 and v2 with the
device currently marked as "End of Life". However, the v2 and latest
v1 firmware are byte-identical. Thus, we only need one image for
this device and do not need to include the revision in the image name.
While at it, remove the useless BOARD_NAME variable which only makes
sense in combination with upgrade from legacy stable versions or when
custom upgrade scripts are involved.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Both devices share most of their setup except buttons and LEDs,
so having a common DTSI removes a lot of duplicate code.
In order to have a shared partitioning scheme, device-id and
product-info from AD7200 have been merged into a single
product-info partition like for C2600.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This does several cosmetic adjustments for AD7200's DTS:
- Make node name, DT label and label property consistent
- Drop wrong and unused spi4 label
- Use generic flash@0 node name
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
While the underscore in the name of the USB LEDs was removed from DTS,
/etc/board.d/01_leds also has to reflect that change.
Fixes: 28fd279e5d ("ipq806x: some corrections for TP-Link Talon AD7200")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Address most comments made by Adrian Schmutzler on the mailing list.
The device name is kept as 'TP-Link Talon AD7200' as that seems to be
the marketing name TP-Link chose for that device, it also matches the
naming scheme for other TP-Link devices (e.g. 'TP-Link Archer C7').
Fixes: 1a775a4fd0 ("ipq806x: add support for TP-Link Talon AD7200")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Device hardware: https://deviwiki.com/wiki/TP-LINK_AD7200_(Talon)
The Talon AD7200 is basically an Archer C2600 with a third PCIe lane
and an 802.11ad radio. It looks like the Archers C2600/5400 but the
housing is slightly larger.
Specifications
--------------
- IPQ8064 dual-core 1400MHz
- QCA9988 2.4GHz WiFi
- QCA9990 5GHz WiFi
- QCA9500 60GHz WiFi
- 32MB SPI Flash
- 512MiB RAM
- 5 GBit Ports (QCA8337)
Installation
------------
Installation is possible from the OEM web interface.
Sysupgrade is possible.
TFTP recovery is possible.
- Image: AD7200_1.0_tp_recovery.bin
Notes
- This will be the first 802.11ad device supported by mainline.
Signed-off-by: Gary Cooper <gaco@bitmessage.de>
Commit 29ca10e537 ("ipq806x: remove support for kernel 4.19") moved
DTS files to "files" directory, but after that a new DTS file was added
to the former "files-5.4" directory. Move it to the new directory.
Fixes: 98b86296e6 ("ipq806x: add support for ASRock G10")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
This reverts commit 57e4cc8261.
Cmdline override patch was fixed. It's time for reenable
Asrock G10 support.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Tested-by: Hannu Nyman <hannu.nyman@iki.fi> (run-tested for R7800)
900-arm-add-cmdline-override.patch have missplaced entry in
arch/arm/Kconfig file. It causes problem with other cmdline
patches. This patch put Kconfig entry in correct place.
Fixes: 98b86296e6 ("ipq806x: add support for ASRock G10")
Suggested-by: Hannu Nyman <hannu.nyman@iki.fi>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Tested-by: Hannu Nyman <hannu.nyman@iki.fi> (run-tested for R7800)
After device support for ASRock G10 was added in [1], several
people reported broken ipq806x devices, with one or several of the
following symptoms:
- Device does not boot
- Sysupgrade does not work
- Serial console is broken
The issues appears to be caused by the introduction of the symbol
CONFIG_CMDLINE_OVERRIDE=y in [1].
This patch disables the corresponding symbol again and marks the
ASRock as BROKEN, as it probably won't work properly without it.
Further references:
https://bugs.openwrt.org/index.php?do=details&task_id=354098b86296e6 (commitcomment-45455875)
[1] 98b86296e6 ("ipq806x: add support for ASRock G10")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This commit adds support for Qualcomm IPQ8062 SoC.
IPQ8062 is a lower clock variant of IPQ8064.
CPU and NSS clocks:
- CPU: 384 MHz - 1 GHz
- NSS: 110 MHz - 550 MHz
opp and l2 clock values are taken from WG2600HP3 GPL source code [1].
Due to a lack of devices, I didn't test the following features.
- SATA
- NAND flash memory controller
- SD
- USB
- GSBI2, GSBI7
- PCIE2
- GMAC0, GMAC3
Works properly:
- GSBI4 UART
- GSBI5 SPI
- GMAC1, GMAC2
- PCIE0, PCIE1
- MDIO0
Does not work properly:
- CPU SPC
- This can cause a system hang. Same as IPQ8065.
See 2336c2dbb1
[1] https://www.aterm.jp/function/wg2600hp3/appendix/opensource.html
Signed-off-by: Yanase Yuki <dev@zpc.sakura.ne.jp>
The ASRock G10 is a 2.4/5 GHz band 11ac "Gaming" router,
based on Qualcomm IPQ8064.
Specifications:
SoC: Qualcomm IPQ8064
CPU: Dual-Core A15 @ (384 - 1,400 MHz, 2C2T)
DRAM: 512 MiB (~467 MiB available)
NAND: 128 MB (Micron MT29F1G08ABBEAH4)
WLAN0: 4T4R 5 GHz Wlan (QCA9980)
WLAN1: 4T4R 2.4 GHz Wlan (QCA9980)
ETH: 5x 10/100/1000 Mbps Ethernet (QCA8337)
INPUT: Reset Button, WPS 2.4G and WPS 5G Button
LEDS: 1 multicolor status LED
USB: 2x USB 3.0 Type-A
POWER: 12VDC/3A AC Adapter + dedicated Power Switch
UART: Setting is 115200-8-N-1. 1x4 .1" unpopulated header
on the PCB (J6 - very tiny silkscreen next to TX).
Pinout: 1. 3v3 (Square - best skipped!), 2. RX, 3. GND, 4. TX
WARNING: The serial port needs a TTL/RS-232 3.3v level converter!
(Depending on the serial adapter RX and TX might need to
be swapped).
Note about the IR-Remote:
There's a 8-Bit MCU (SONIX SN8F25E21SG) which is controlling the
IR-Remote and is fed by the IR-Photodiode. The SoC can talk to
the device via I2C. The vendor's GPL archive comes with the source
of the interface driver for this as a (character driver), the main
control software is however a blob.
Installation Instructions:
1. Download factory image to disk
2. Apply factory image via stock web-gui
Back to stock:
1. Login to router via ssh
2. run "asrock_g10_back_to_factory" script from /sbin
Notes:
- If something goes wrong durring sysupgrade, router will go back to
factory image.
- Asrock G10 uses partition layout from smem. So partition layout can
be normal or alternate.
- 900-arm-add-cmdline-override.patch was copied from 102-powerpc-add-cmdline-override.patch
from powerpc target.
Knowledge about BOOTCONFIG partition was based on user "jmomo" post from old
OpenWrt forum (Post #50):
https://forum.archive.openwrt.org/viewtopic.php?id=65956&p=2
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[bump to 5.4, add factory image, fix sysupgrade, convert partition
layout to smem, remove ipq-wifi-asrock-g10 and use ART, minor fixes]
Co-Authored-by: Pawel Dembicki <paweldembicki@gmail.com>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Tested-by: Lukasz Ostapiuk <palibrzuch@gmail.com>
