Commit Graph

24087 Commits

Author SHA1 Message Date
David Bauer
6090337679 generic: add missing symbols
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 55ed4bf6d7)
2021-04-03 17:06:39 +02:00
INAGAKI Hiroshi
6f42758000 ath79: fix label_mac for NEC Aterm WG1200CR
On NEC Aterm WG1200CR, the MAC address for WAN is printed in the label
on the case, not LAN.
This patch fixes this issue.

Fixes: 50fdc0374b ("ath79: provide label MAC address")

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
(cherry picked from commit e2331fb549)
2021-04-02 16:04:47 +02:00
Shiji Yang
b8eb602934 ramips: correct switch config of Youku yk1
There are only two lan ports and one wan port on Youku yk1

Fixes: e9baf8265b ("ramips: add support for Youku YK1")

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
[add Fixes:]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit b88d2850c6)
2021-04-02 16:04:00 +02:00
Robert Marko
da7ef7f414 ipq40xx: net: phy: qca807x: fix GPIO driver
While rebasing into setting bits instead of magic values,
I accidentally forgot to actually set the force bit.

Without it using the pins as GPIO-s did not actually work.

Fixes: b5c93ed ("ipq40xx: add Qualcomm QCA807x driver")

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
(cherry picked from commit 7f2d9ccd09)
2021-03-29 22:26:27 +02:00
Daniel Golle
c61d4eeedb ath79: fix RS-485 on Teltonika RUT-955
DTR GPIO isn't actually needed and triggers boot warning.
TX pin was off by one (GPIO 19 instead of GPIO 18).

Reported-by: @tophirsch
Fixes: d1130ad265 ("ath79: add support for Teltonika RUT955")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 53a7d5d614)
2021-03-29 22:26:27 +02:00
Aleksander Jan Bajkowski
eb1509a938 lantiq: set maximum kernel size for ARV7519RW22
Some users report that current snapshot producies non-bootable images.
Stock uboot can boot images if the kernel is smaller than 2MB.

Set maximum kernel size and disable image building for this board.

Ref: https://forum.openwrt.org/t/astoria-arv7519rw22-bootloops-after-upgrade/89843
Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
(cherry picked from commit c027dbac5a)
2021-03-29 22:26:27 +02:00
Sven Eckelmann
eb98c88f66 mvebu: Fix mac addresses for GL.iNet GL-MV1000
The original GL.iNet firmware has two different mac addresses in the
factory/art partition. The first one is for the WAN interface only and the
second one is for both lan0 and lan1.

But the original submission for OpenWrt didn't initialize the mac
addresses of the LAN ports for the DSA device at all. The ethernet mac
address was then used for all DSA ports.

Fixes: 050c24f05c ("mvebu: add support for GL.iNet GL-MV1000")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
(cherry picked from commit c20ac84803)
2021-03-29 21:41:16 +02:00
Sven Eckelmann
7bb8aded10 mvebu: Add button support for GL.iNet GL-MV1000
The original patch to support this device advertised support for the reset
button and the "switch" in the commit message. But neither were actually
integrated in the device tree or documented anywere.

The button itself is now used to trigger a reset (as described in the
official GL.iNet documentation). The switch itself is registered as BTN_0
like other devices from GL.iNet in ath79.

Fixes: 050c24f05c ("mvebu: add support for GL.iNet GL-MV1000")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
(cherry picked from commit 01b911a938)
2021-03-29 21:38:24 +02:00
Tad Davanzo
9ce0f2b90c mvebu: enable WRT1900AC v1 and WRT32X for buildbots
Kernel size limits have been dealt with.
Effective revert of a1eb2c46 and ac9730c4.

Signed-off-by: Tad Davanzo <tad@spotco.us>
(cherry picked from commit b4f76d9f0d)
2021-03-29 21:17:32 +02:00
Tad Davanzo
5a3b1e5b57 mvebu: venom resize kernel to 6MB
venom has a 3MB kernel partition as specified by the DTS.
3MB is not sufficient for building with many kernel modules or newer
kernel versions.

venom uboot however as set from factory will load up to 6MB.
This can be observed by looking a uboot log:
	NAND read: device 0 offset 0x900000, size 0x600000
	6291456 bytes read: OK
and from uboot environment variables:
	$ fw_printenv | grep "priKernSize";
	priKernSize=0x0600000

Resize the root partitions from 120MB to 117MB to let kernel expand
into it another 3MB.
And set kernel target size to 6MB.

Lastly set the kernel-size-migration compatibility version on venom to
prevent sysupgrading without first reinstalling from a factory image.

Signed-off-by: Tad Davanzo <tad@spotco.us>
(cherry picked from commit 15309f5133)
2021-03-29 21:17:32 +02:00
Tad Davanzo
8458ebe18b mvebu: mamba resize kernel to 4MB
mamba has a 3MB kernel partition as specified by the DTS.
3MB is not sufficient for building with many kernel modules or newer
kernel versions.

mamba uboot however as set from factory will load up to 4MB.
This can be observed by looking a uboot log:
	NAND read: device 0 offset 0xa00000, size 0x400000
	4194304 bytes read: OK
and from uboot environment variables:
	$ fw_printenv | grep "pri_kern_size";
	pri_kern_size=0x400000

Resize the root partitions from 37MB to 36MB to let kernel expand
into it another 1MB.
And set kernel target size to 4MB.

Lastly add a compatibility version message: kernel-size-migration.
And set it on mamba to prevent sysupgrading without first reinstalling from
a factory image.

Signed-off-by: Tad Davanzo <tad@spotco.us>
(cherry picked from commit 10415d5e70)
2021-03-29 21:17:31 +02:00
Ilya Lipnitskiy
2db7fe792e kernel: backports: mt7530: fix TRGMII mode after reset
Backport upstream patch that fixes TRGMII mode now that mt7530 is
actually resetting the switch on ramips devices.

Patches apply to both Linux 5.4 and 5.10, since TRGMII is broken on both.

Fixes: 69551a2442 ("ramips: manage low reset lines")
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
(cherry picked from commit 680f91d0e5)
2021-03-29 13:41:24 +08:00
Hauke Mehrtens
112d1052ac kernel: Deactivate CONFIG_VFIO in generic kernel config
Instead of deactivating this in every target config, deactivate it once
in the generic kernel config. I was asked for this config option in a
x86 64 build in OpenWrt 21.02.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 7d6553c72e)
2021-03-27 16:26:56 +01:00
Hauke Mehrtens
2464a9a8a4 kernel: bump 5.4 to 5.4.108
Refreshed all patches.

Compile-tested on: x86_64, ath79, lantiq
Runtime-tested on: x86_64, ath79

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2021-03-27 16:26:56 +01:00
Mauri Sandberg
e8cbdbbe97 ath79: Add support for Buffalo WZR-HP-G300NH
This device is a wireless router working on 2.4GHz band based on
Qualcom/Atheros AR9132 rev 2 SoC and is accompanied by Atheros AR9103
wireless chip and Realtek RTL8366RB/S switches. Due to two different
switches being used also two different devices are provided.

  Specification:
  - 400 MHz CPU
  - 64 MB of RAM
  - 32 MB of FLASH (NOR)
  - 3x3:2 2.4 GHz 802.11bgn
  - 5x 10/100/1000 Mbps Ethernet
  - 4x LED, 3x button, On/Off slider, Auto/On/Off slider
  - 1x USB 2.0
  - bare UART header place on PCB

  Flash instruction:
  - NOTE: Pay attention to the switch variant and choose the image to
    flash accordingly. (dmesg / kernel logs can tell it)
  - Methods for flashing
    - Apply factory image in OEM firmware web-gui.
    - Sysupgrade on top of existing OpenWRT image
    - U-Boot TFPT recovery for both stock or OpenWRT images:
      The device U-boot contains a TFTP server that by default has
      an address 192.168.11.1 (MAC 02:AA:BB:CC:DD:1A). During the boot
      there is a time window, during which the device allows an image to
      be uploaded from a client with address 192.168.11.2. The image will
      be written on flash automatically.

      1) Have a computer with static IP address 192.168.11.2 and the
         router device switched off.
      2) Connect the LAN port next to the WAN port in the device and the
         computer using a network switch.
      3) Assign IP 192.168.11.1 the MAC address 02:AA:BB:CC:DD:1A
         arp -s 192.168.11.1 02:AA:BB:CC:DD:1A
      4) Initiate an upload using TFTP image variant
         curl -T <imagename> tftp://192.168.11.1
      5) Switch on the device. The image will be uploaded subsequently.
         You can keep an eye on the diag light on the device, it should
         keep on blinking for a while indicating the writing of the image.

  General notes:
  - In the stock firmware the MAC address is the same among all
    interfaces so it is left here that way too.

  Recovery:
  - TFTP method
  - U-boot serial console

  Differences to ar71xx platform
  - This device is split in two different targets now due to hardware
    being a bit different under the hood. Dynamic solution within the same
    image is left for later time.
  - GPIOs for a sliding On/Off switch, marked 'Movie engine' on the device
    cover, were the wrong way around and were renamed qos_on -> movie_off,
    qos_off -> movie_on. Associated key codes remained the same they were.

  The device tree source code is mostly based on musashino's work

Signed-off-by: Mauri Sandberg <sandberg@mailfence.com>
(cherry picked from commit bc356de285)
2021-03-27 07:47:07 +01:00
Mauri Sandberg
8e8fe69a8e ath79: cfi: cmdset_0002: amd chip 0x2201 - write words
Generally, in upstream CFI flash memory driver uses buffers for write
operations. That does not work with AMD chip with id 0x2201 and we must
resort to writing word sized chunks only. That is, to not apply general
buffer write functionality for this given chip.

Without the patch kernel logs will be flooded with entries like below:

MTD do_erase_oneblock(): ERASE 0x01fa0000
MTD do_write_buffer(): WRITE 0x01fa0000(0x00001985)
MTD do_erase_oneblock(): ERASE 0x01f80000
MTD do_write_buffer(): WRITE 0x01f80000(0x00001985)
MTD do_write_buffer_wait(): software timeout, address:0x01f8000a.
jffs2: Write clean marker to block at 0x01a60000 failed: -5
MTD do_erase_oneblock(): ERASE 0x01f60000
MTD do_write_buffer(): WRITE 0x01f60000(0x00001985)
MTD do_write_buffer_wait(): software timeout, address:0x01f6000a.
jffs2: Write clean marker to block at 0x01a40000 failed: -5

References: http://patchwork.ozlabs.org/project/linux-mtd/patch/20210309174859.362060-1-sandberg@mailfence.com/
Signed-off-by: Mauri Sandberg <sandberg@mailfence.com>
[added link to usptream fix submission]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit 8cc0fa8fac)
2021-03-27 07:46:48 +01:00
INAGAKI Hiroshi
0444a93bdf ramips: add support for ELECOM WRC-1750GST2
ELECOM WRC-1750GST2 is a 2.4/5 GHz band 11ac (Wi-Fi 5) router, based on
MT7621A.

Specification:

- SoC		: MediaTek MT7621A
- RAM		: DDR3 256 MiB (NT5CC128M16JR-EK)
- Flash		: SPI-NOR 32 MiB (MX25L25645GMI-08G)
- WLAN		: 2.4/5 GHz 3T3R (2x MediaTek MT7615)
- Ethernet	: 10/100/1000 Mbps x5
  - Switch	: MediaTek MT7530 (SoC)
- LEDs/Keys	: 4x/6x (2x buttons, 1x slide-switch)
- UART		: through-hole on PCB
  - J4: 3.3V, GND, TX, RX, from ethernet port side
  - 57600n8
- Power		: 12 VDC, 1.5 A

Flash instruction using factory image:

1. Boot WRC-1750GST2 normally with "Router" mode
2. Access to "http://192.168.2.1/" and open firmware update page
   ("ファームウェア更新")
3. Select the OpenWrt factory image and click apply ("適用") button
4. Wait ~120 seconds to complete flashing

MAC addresses:

LAN	: 04:AB:18:xx:xx:23 (Factory, 0xE000 (hex))
WAN	: 04:AB:18:xx:xx:24 (Factory, 0xE006 (hex))
2.4GHz	: 04:AB:18:xx:xx:25 (Factory, 0x4    (hex))
5GHz	: 04:AB:18:xx:xx:26 (Factory, 0x8004 (hex))

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
(cherry picked from commit b3ca1f30ef)
2021-03-22 21:07:34 +01:00
Walter Sonius
c459d5a710 ath79: fix lan port display order for sitecom wlr-7100
Physical port order watched from the back of the device is:
4 / 3 / 2 / 1 / WAN which also matches corresponding leds.
This patch corrects LuCI switch webpage LAN port order.

Signed-off-by: Walter Sonius <walterav1984@gmail.com>
[improve commit title, fix sorting in 02_network]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 46c0634b50)
2021-03-22 21:06:40 +01:00
Jeff Collins
db6ff390b0 mvebu: add LED support for GL.iNet GL-MV1000
This patch enables LED support for the GL.iNet GL-MV1000

Signed-off-by: Jeff Collins <jeffcollins9292@gmail.com>
[add SPDX identifier on new file, add aliases, minor cosmetic issues]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 6e0c780eb3)
2021-03-22 21:05:41 +01:00
Álvaro Fernández Rojas
cd48473bb8 bcm27xx: bcm2711: correctly disable HW_RANDOM_BCM2835
It was removed in bac74aff5e, but it should have been disabled.
More info: https://forum.openwrt.org/t/make-image-stops-at-random-number-generator-bcm27xx/91429/7

Fixes: bac74aff5e ("bcm27xx: bcm2711: disable HW_RANDOM_BCM2835")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit f93b544f01)
2021-03-22 08:09:13 +01:00
Hauke Mehrtens
31bca5f256 archs38: Add CONFIG_HZ=100
This kernel config option was missing and resulted in a question when
building.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 047b7621bb)
2021-03-19 18:01:55 +01:00
Rafał Miłecki
192486ac74 bcm53xx: backport first 5.13 DTS changes
This adds NVMEM bindings that are needed for proper booting on Linksys
devices.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 98d456a14e)
2021-03-17 23:38:46 +01:00
Rafał Miłecki
761df5c4cf bcm47xx: make WGT634U NVRAM patch apply again
Fixes: 1c48eee5b2 ("kernel: backport Broadcom NVRAM driver cleanups")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 9530b9bb78)
2021-03-17 23:38:46 +01:00
Rafał Miłecki
20fe0e66f3 bcm53xx: initialize NVRAM from NVMEM driver
NVRAM access may be needed early in boot process. Reading it using mtd
happens quite late in the init process. Add NVRAM initialization to the
NVMEM driver which comes up early and depends on IO mapping only.

This is required by Linksys devices which use NVRAM content for proper
partitioning (detecting current firmware partition).

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit baf04eed02)
2021-03-17 23:38:46 +01:00
Rafał Miłecki
946bfd59a6 kernel: backport Broadcom NVRAM driver cleanups
Refactoring of bcm47xx_nvram driver. It's used by bcm47xx and bcm53xx.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 1c48eee5b2)
2021-03-17 23:38:46 +01:00
Rafał Miłecki
3ce0d62b39 bcm53xx: backport NVMEM NVRAM driver
It supports NVRAM access described using DT binding. Right now NVRAM
data is exposed using /sys/bus/nvmem/ only.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 01b1b37528)
2021-03-17 23:38:46 +01:00
Rafał Miłecki
d523f61135 bcm53xx: backport more upstream dts stuff from kernel 5.11
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 8078d89a53)
2021-03-17 23:38:41 +01:00
Rafał Miłecki
7d03fdb004 bcm53xx: group dts backports by upstream kernel version
It's a simple renaming thing.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit d0ee398c36)
2021-03-17 23:26:12 +01:00
Rafał Miłecki
15d142262a bcm4908: backport recent bcm_sf2 changes
One 5.12 link fix and 5.13 crossbar support.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit e1b4fd52a8)
2021-03-17 21:24:24 +01:00
Rafał Miłecki
86eb3de66e bcm4908: backport recent bcm4908_enet changes
This includes 5.12 fix and 5.13 improvements.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 7091e31230)
2021-03-17 21:24:24 +01:00
Rafał Miłecki
763f0bab3e bcm4908: backport first PHY 5.13 patches
1. Upstream accepted version of Kconfig change
2. Documentation binding fix

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit d7c8ca4d0b)
2021-03-17 21:24:24 +01:00
Rafał Miłecki
b18fe2ecc4 bcm4908: use accepted 5.13 DTS patches
Some patches were slightly cleaned up. One things worth mentioning is
that adding:
phy-mode = "rgmii"
broke SF2 driver. It made it access random register breaking switch
setup.

That's why this commit also adds a quick sf2 fix.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 05dbfe616d)
2021-03-17 21:24:24 +01:00
Rafał Miłecki
6a217d6d72 kernel: add pending mtd patches adding NVMEM support
It's meant to provide upstream support for mtd & NVMEM. It's required
e.g. for reading MAC address from mtd partition content. It seems to be
in a final shape so it's worth testing.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit e90e75b12c)
2021-03-17 21:24:22 +01:00
Rafał Miłecki
c8b415035c kernel: move mtd ofpart accepted patch
Move upstream patch to the backport directory.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit deceb03993)
2021-03-17 21:23:56 +01:00
Rafał Miłecki
bc2c3d99c8 bcm4908: prepare to support TP-Link Archer C2300 V1
It's a BCM4906 based device (2 CPU cores). It has 512 MiB of RAM, 4 LAN
ports, 1 WAN port, 2 USB ports, NAND flash. WiFi unknown at this point.

Flashing is possible using CFE only, proper image will be worked on
later.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 8d24da1470)
2021-03-17 21:23:46 +01:00
Rafał Miłecki
543007917a kernel: add the latest mtd patch extending ofpart parser
This adds the latest version of ofpart commit. It hopefully
1. Doesn't break compilation
2. Doesn't break partitioning
(this time).

It's required to implement fixed partitioning with some quirks. It's
required by bcm53xx, bcm4908, kirkwood, lantiq and mvebu.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 7a7b2fd809)
2021-03-17 21:23:38 +01:00
Rafał Miłecki
67df3a829b bcm4908: backport Ethernet driver fixes from the 5.12
The most noticeable one is fix for RX stopping on high traffic.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit acbea54bc2)
2021-03-17 21:22:29 +01:00
Rafał Miłecki
08bbe361e0 bcm4908: add bcm_sf2 fixes for the 5th GPHY
This allows using the last integrated PHY (and so e.g. WAN port on the
ASUS GT-AC5300).

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit ad8b759fd1)
2021-03-17 21:22:29 +01:00
Hauke Mehrtens
f82e7e96a0 kernel: bump 5.4 to 5.4.105
Refreshed all patches.

The following patches were applied upstream:
* 755-v5.8-net-dsa-add-GRO-support-via-gro_cells.patch
* 831-v5.9-usbip-tools-fix-build-error-for-multiple-definition.patch

Compile-tested on: x86_64, ipq40xx, ath79
Runtime-tested on: x86_64, ipq40xx, ath79

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2021-03-16 00:31:16 +01:00
Ilya Lipnitskiy
94077a2f12 ramips: rename mtk-hsdma to hsdma-mt7621
Follows upstream rename:
https://lore.kernel.org/driverdev-devel/20210130034507.2115280-1-ilya.lipnitskiy@gmail.com/

Fixes ramips builds on 5.4.102

Cc: John Audia <graysky@archlinux.us>
Cc: David Bauer <mail@david-bauer.net>
Cc: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
(cherry picked from commit 58ad113087)
2021-03-15 10:32:53 -10:00
Felix Fietkau
1eb1d5e0bb kernel: add compatibility with upstream threaded NAPI patch
Enable threading if dev->threaded is set. This will be used to bring mt76 back
in sync with upstream

Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry-picked from commit 3d1ea0d77f)
2021-03-14 20:41:58 +01:00
Daniel González Cabanelas
3b6c93298c bcm63xx: AD1018-nor: add NAND flash
The Sercomm AD1018 has a NAND flash. We recently added support for NANDs
in this target.

Use the internal NAND as additional storage.

Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
(cherry-picked from commit a48ef37747)
2021-03-08 12:46:46 +01:00
Hauke Mehrtens
8b3d879861 kernel: bump 5.4 to 5.4.102
Refreshed all patches.

Compile-tested on: ath79, lantiq, ipq40xx, x86_64
Runtime-tested on: ipq40xx, x86_64

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2021-03-06 15:51:54 +01:00
Rui Salvaterra
7e1ab3b746 kernel: backport GCC 10 usbip build fix for 5.4
From the original commit message:

"With GCC 10, building usbip triggers error for multiple definition
of 'udev_context', in:
- libsrc/vhci_driver.c:18 and
- libsrc/usbip_host_common.c:27.

Declare as extern the definition in libsrc/usbip_host_common.c."

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
(cherry picked from commit 0eef8402ee)
2021-03-05 14:54:35 +01:00
Daniel González Cabanelas
5601da24a8 kernel: b53: update the BCM5365 UID
BCM63XX internal PHYs and BCM5365 SoC internal switch are both using the
same phy_driver->phy_id, causing conflicts and unnecessary probes. E.g
the BCM63XX phy internal IRQ is lost on the first probe.

The full BCM5365 UID is 0x00406370.

Use an additional byte to mask the BCM5365 UID to avoid duplicate driver
phy_id's. This will fix the IRQ issue in internal BCM63XX PHYs and avoid
more conflicts in the future.

Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
(merge both cherry-picked commits)
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry-picked from commits cbcac4fde8 and cfa43f8119)
2021-03-05 12:23:25 +01:00
Álvaro Fernández Rojas
bdb18e0f84 bcm27xx: bcm2711: disable HW_RANDOM_BCM2835
This driver is only present on BCM2708, BCM2709 and BCM2710.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry-picked from commit bac74aff5e)
2021-03-05 12:16:04 +01:00
Pawel Dembicki
59ba79d675 mpc85xx: p2020: fix cfi-nor detection
At this moment p2020rdb has broken images, because NOR memory connected
to eLBC bus isn't detected.

In 642b1e8dbed7 linux tree commit, config dependencies of MTD_PHYSMAP_OF
was changed and now MTD_PHYSMAP is required.

This patch adds MTD_PHYSMAP option to kernel config in p2020 subtarget
and fix booting of p2020rdb.

Fixes: 13b1db795f ("mpc85xx: add support for kernel 5.4")

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
(cherry picked from commit 76649fd06d)
2021-03-01 21:49:55 +01:00
Rui Salvaterra
17a627ec82 mvebu/omnia: fix the device tree
Backport [1] and fix [2] hardware buffer management. Also fix the IRQ storm
caused by a misconfiguration of the PCA9538 interrupt pin [3].

[1] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/arch/arm/boot/dts/armada-385-turris-omnia.dts?id=018b88eee1a2efda26ed2f09aab33ccdc40ef18f
[2] https://lore.kernel.org/linux-arm-kernel/20210217153038.1068170-1-rsalvaterra@gmail.com/
[3] https://lore.kernel.org/linux-arm-kernel/20210220231144.32325-1-kabel@kernel.org/

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
(cherry picked from commit 6fe6b631ef)
2021-03-01 13:41:29 +01:00
Mathias Kresin
2638c9801f lantiq: set maximum kernel size
These boards have a fixed size kernel partition but do not limit the
kernel size during image building.

Disable image building for both boards as well, since the kernel of the
last release as well as master are to big to fit into the 2 MByte kernel
partition.

Signed-off-by: Mathias Kresin <dev@kresin.me>
(cherry picked from commit 23dd786734)
2021-03-01 00:23:30 +01:00
Adrian Schmutzler
adc3a75d48 octeon: re-enable CONFIG_CAVIUM_CN63XXP1 and EdgeRouter image
The symbol CONFIG_CAVIUM_CN63XXP1 was disabled during the bump to
4.19 (see Fixes:) with the following reason:

  No supported hardware uses CN63XXP1 and it causes "slight decrease
  in performance"

However, it later turned out that the edgerouter image needed it,
which led to having the device disabled in [1].
Still, dropping support of a device seems a harsh action for just
removing a "slight" decrease in performance from the other devices.

Thus, this enables CONFIG_CAVIUM_CN63XXP1 again, and essentially
restores the situation present until (including) kernel 4.14 on
this target.

For OpenWrt as a platform, it seems more desirable to support all
devices (and have them tested regularly via the snapshots) in this
case.
Users interested in maximum performance might still just remove
the symbol again in their local build.

[1] 3824fa26d2 ("octeon: disable edgerouter image")

Fixes: 6c22545225 ("target/octeon: Add Linux 4.19 support")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit cfd1a40583)
2021-02-28 21:56:39 +01:00
Adrian Schmutzler
3feef9c555 ath79: enable UART node for GL-USB150
This was overlooked when adding support for this device.
(It has recently been discovered that this was the only device in
ath79 having &uart disabled.)

Fixes: acc6263013 ("ath79: add support for GL.iNet GL-USB150")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 722f1bd549)
2021-02-25 15:13:13 +01:00
Adrian Schmutzler
7054721cf9 ath79: enable UART in SoC DTSI files
The uart node is enabled on all devices except one (GL-USB150 *).
Thus, let's not have a few hundred nodes to enable it, but do not
disable it in the first place.

Where the majority of devices is using it, also move the serial0
alias to the DTSI.

*) Since GL-USB150 even defines serial0 alias, the missing uart
   is probably just a mistake. Anyway, disable it for now so this
   patch stays cosmetic.

Apply this to 21.02 as well to remove an unnecessary backporting
pitfall.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 3a4b751110)
2021-02-25 14:42:11 +01:00
Sander Vanheule
c53a86806d ramips: mt7621: enable SX150x driver
The Netgear R6800 and R6700v2 devices have a Semtech SX1503 GPIO
expander controlling the device LEDs. This expander was initially
supported on 4.14, but support was lost in the transition to 5.4.

Since this driver cannot be built as a kernel module, enable it in the
kernel config for all mt7621 devices.

Run-tested on a Netgear R6800.

Cc: Stijn Segers <foss@volatilesystems.org>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Tested-by: Stijn Segers <foss@volatilesystems.org>
(cherry picked from commit 773949c152)
2021-02-24 20:23:59 +01:00
Stijn Segers
0a19f77f32 ramips: overwrite reset gpio properties in DIR-860L DTS
As suggested by Sergio, this adds GPIOs 19 and 8 explicitly into the
DIR-860L DTS, so the PCI-E ports get reset and the N radio (radio1)
on PCI-E port 1 comes up reliably.

Fixes the following error that popped up in dmesg:

    [    1.638942] mt7621-pci 1e140000.pcie: pcie1 no card, disable it (RST & CLK)

Suggested-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Stijn Segers <foss@volatilesystems.org>
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
(cherry picked from commit 06356f0020)
2021-02-24 20:23:52 +01:00
Daniel González Cabanelas
8f7a905ffb bcm63xx: pinctrl: fix BCM6348 groups
The current driver has some troubles:
 - Some groupings are wrong.
 - The pinctrl group0 owns pins never used (at least in Openwrt) for any
   pinmux. The driver hijacks all the pins on the group avoiding any other
   use, spite they're free. I.e. for buttons, causing this kernel error:
   [  4.735928] gpio-keys-polled keys: unable to claim gpio 479, err=-22
   [  4.742642] gpio-keys-polled: probe of keys failed with error -22
 - Minor errors about groupings on the documentation
 - Missing "diag" grouping in dtsi
 - Wrong groupings in dtsi

Fix it by setting the correct groups.
And relax the pin capturing, letting the gpios belonging to any group to
be used for other purposes like buttons. This was the behavior with stock
firmwares and old OpenWrt versions which never caused any trouble.

Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
(Cherry-picked from commit 50cb3a750f)
2021-02-23 11:17:51 +01:00
Álvaro Fernández Rojas
e3e6ec3cda bcm63xx: limit name metadata to model name
Since there are only 16 characters available, on most cases the vendor name
will fit in the metadata, but the model name won't fit.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry-picked from commit c27532742d)
2021-02-23 08:35:59 +01:00
Shiji Yang
3c1aabd445 ramips: fix Phicomm PSG1218A switch port labels
The lan port sequence was reversed compared to the labels.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
[improve commit title/message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 567a88e4b9)
2021-02-22 18:51:55 +01:00
Shiji Yang
64ca28a881 ramips: correct/add Phicomm K2x WAN/label MAC address
Phicomm K2G:
add missing label_mac

Phicomm PSG1218A & PSG1218B:
The previous wan mac was set as factory@0x28 +1 (originally based
on the default case for the ramips target), but the correct wan mac
is factory@0x28 -1, being equal to factory@0x2e.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
[minor commit title/message adjustments]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 55263ffedb)
2021-02-22 17:33:43 +01:00
Álvaro Fernández Rojas
4b3958da39 bcm63xx: bcm63268: fix GPIO interrupts
pinctrl should rely on external interrupt controller for GPIO interrupts.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry-picked from commit 36e35b8d81)
2021-02-22 09:10:08 +01:00
Álvaro Fernández Rojas
8cb50639c7 bcm27xx: remove urngd package
Now that khwrngd is working on all subtargets we can remove urgnd.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry-picked from commit 9dc84018ee)
2021-02-20 19:57:33 +01:00
Álvaro Fernández Rojas
b7c5924f1f bcm27xx: enable bcm2711 HW RNG
Also add a patch setting its quality, which should make it usable by khwrngd.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry-picked from commit 670526efa3)
2021-02-20 19:57:15 +01:00
Álvaro Fernández Rojas
906c87814d generic: add bcm2835-rng quality patch
This patch allows devices without a high resolution timer to boot up faster.
It should speed up boots for bcm2708 and bcm63xx.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry-picked from commit 7747b3fa36)
2021-02-20 19:02:18 +01:00
Stijn Segers
7a0cd1ede4 ramips: overwrite reset gpio properties in EX6150 DTS
The Netgear EX6150 can, just like the D-Link DIR-860L rev B1, fail to
initialise both radios in some cases. Add the reset GPIOs explicitly
so the PCI-E devices get re-initialised properly. See also FS #3632.

Error shows up in dmesg as follows:

  [    1.560764] mt7621-pci 1e140000.pcie: pcie1 no card, disable it (RST & CLK)

Tested-by: Kurt Roeckx <kurt@roeckx.be>
Signed-off-by: Stijn Segers <foss@volatilesystems.org>
[removed period from commit title]
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit af1b6799c6)
2021-02-20 09:39:58 +01:00
Yangbo Lu
ef47bc424c layerscape: add new devices in README and clean up
Support new devices LS1046AFRWY and LX2160ARDB in README.
Clean up README, and add missing LS1021ATWR deploy guide.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
[adjust set of devices added, update commit message/title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit a31842e7fd)
2021-02-19 20:09:29 +01:00
Yangbo Lu
2e1ad2473e layerscape: add LX2160ARDB (Rev2.0 silicon) board support
The QorIQ LX2160A reference design board provides a comprehensive platform
that enables design and evaluation of the LX2160A processor.

- Enables network intelligence with the next generation Datapath (DPPA2)
  which provides differentiated offload and a rich set of IO, including
  10GE, 25GE, 40GE, and PCIe Gen4

- Delivers unprecedented efficiency and new virtualized networks

- Supports designs in 5G packet processing, network function
  virtualization, storage controller, white box switching, network
  interface cards, and mobile edge computing

- Supports all three LX2 family members (16-core LX2160A; 12-core LX2120A;
  and 8-core LX2080A)

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
[use AUTORELEASE, add dtb to firmware part]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 80dcd14abe)
2021-02-19 20:09:29 +01:00
Yangbo Lu
7f933db108 layerscape: add FRWY-LS1046A board support
The LS1046A Freeway board (FRWY) is a high-performance computing,
evaluation, and development platform that supports the QorIQ
LS1046A architecture processor capable of support more than 32,000
CoreMark performance. The FRWY-LS1046A board supports the QorIQ
LS1046A processor, onboard DDR4 memory, multiple Gigabit Ethernet,
USB3.0 and M2_Type_E interfaces for Wi-Fi.

The FRWY-LS1046A-TP includes the Coral Tensor Flow Processing Unit
that offloads AI/ML inferencing from the CPU to provide significant
boost for AI/ML applications. The FRWY-LS1046A-TP includes one M.2
TPU module and more modules can easily be added including USB
versions of the module to scale the AI/ML performance.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
[rebase, use AUTORELEASE, fix sorting, add dtb to firmware part]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 2c2d77bd3b)
2021-02-19 20:09:28 +01:00
Adrian Schmutzler
9f8bf18c7f layerscape: move rework-sdcard-images out of fsl-sdboot
Upcoming devices will not need the migration setup, so let's move
it out of the common definition.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit a9075d42d7)
2021-02-19 20:09:28 +01:00
Seo Suchan
800a568df5 ramips: use lzma-loader for Wevo devices
As kernel size increased it start to fail to load squishfs image,
using lzma-loader fixed it.
wevo_11acnas is almost same device as w2914ns-v2 except ram size,
so I expect same thing would've happen in that device too.

Signed-off-by: Seo Suchan <abnoeh@mail.com>
Reviewed-by: Sungbo Eo <mans0n@gorani.run>
(cherry picked from commit ca6954e2dc)
2021-02-19 20:09:28 +01:00
Sander Vanheule
a7c0c9bb7e ramips: mt7621: add TP-Link EAP235-Wall support
The TP-Link EAP235-Wall is a wall-mounted, PoE-powered AC1200 access
point with four gigabit ethernet ports.

When connecting to the device's serial port, it is strongly advised to
use an isolated UART adapter. This prevents linking different power
domains created by the PoE power supply, which may damage your devices.

The device's U-Boot supports saving modified environments with
`saveenv`. However, there is no u-boot-env partition, and saving
modifications will cause the partition table to be overwritten. This is
not an issue for running OpenWrt, but will prevent the vendor FW from
functioning properly.

Device specifications:
* SoC: MT7621DAT
* RAM: 128MiB
* Flash: 16MiB SPI-NOR
* Wireless 2.4GHz (MT7603EN): b/g/n, 2x2
* Wireless 5GHz (MT7613BEN): a/n/ac, 2x2
* Ethernet: 4× GbE
  * Back side: ETH0, PoE PD port
  * Bottom side: ETH1, ETH2, ETH3
* Single white device LED
* LED button, reset button (available for failsafe)
* PoE pass-through on port ETH3 (enabled with GPIO)

Datasheet of the flash chip specifies a maximum frequency of 33MHz, but
that didn't work. 20MHz gives no errors with reading (flash dump) or
writing (sysupgrade).

Device mac addresses:
Stock firmware uses the same MAC address for ethernet (on device label)
and 2.4GHz wireless. The 5GHz wireless address is incremented by one.
This address is stored in the 'info' ('default-mac') partition at an
offset of 8 bytes.
From OEM ifconfig:
    eth     a4:2b:b0:...:88
    ra0     a4:2b:b0:...:88
    rai0    a4:2b:b0:...:89

Flashing instructions:
* Enable SSH in the web interface, and SSH into the target device
* run `cliclientd stopcs`, this should return "success"
* upload the factory image via the web interface

Debricking:
U-boot can be interrupted during boot, serial console is 57600 baud, 8n1
This allows installing a sysupgrade image, or fixing the device in
another way.
* Access serial header from the side of the board, close to ETH3,
  pin-out is (1:TX, 2:RX, 3:GND, 4:3.3V), with pin 1 closest to ETH3.
* Interrupt bootloader by holding '4' during boot, which drops the
  bootloader into its shell
* Change default 'serverip' and 'ipaddr' variables (optional)
* Download initramfs with `tftpboot`, and boot image with `bootm`
    # tftpboot 84000000 openwrt-initramfs.bin
    # bootm

Revert to stock:
Using the tplink-safeloader utility from the firmware-utils package,
TP-Link's firmware image can be converted to an OpenWrt-compatible
sysupgrade image:
  $ ./staging_dir/host/bin/tplink-safeloader -B EAP235-WALL-V1 \
      -z EAP235-WALLv1_XXX_up_signed.bin -o eap235-sysupgrade.bin

This can then be flashed using the OpenWrt sysupgrade interface. The
image will appear to be incompatible and must be force flashed, without
keeping the current configuration.

Known issues:
- DFS support is incomplete (known issue with MT7613)
- MT7613 radio may stop responding when idling, reboot required.
  This was an issue with the ddc75ff704 version of mt76, but appears to
  have improved/disappeared with bc3963764d.
  Error notice example:
  [ 7099.554067] mt7615e 0000:02:00.0: Message 73 (seq 1) timeout

Hardware was kindly provided for porting by Stijn Segers.

Tested-by: Stijn Segers <foss@volatilesystems.org>
Signed-off-by: Sander Vanheule <sander@svanheule.net>
(cherry picked from commit 1e75909a35)
2021-02-19 20:09:28 +01:00
Stijn Segers
425c4c89b0 ramips: remove factory image for TP-Link Archer C20 v1
Similarly to the Archer C2 v1, the Archer C20 v1 will brick when one
tries to flash an OpenWrt factory image through the TP-Link web UI.
The wiki page contains an explicit warning about this [1].

Disable the factory image altogether since it serves no purpose.

[1] https://openwrt.org/toh/tp-link/tp-link_archer_c20_v1#installation

Signed-off-by: Stijn Segers <foss@volatilesystems.org>
(cherry picked from commit 0265cba40a)
2021-02-19 20:09:28 +01:00
Álvaro Fernández Rojas
c74df745fd bcm63xx: update ethernet kernel panics fix
Use new patch from Sieng Piaw Liew.

Signed-off-by: Sieng Piaw Liew <liew.s.piaw@gmail.com>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry-picked from commit 31a06f8fcc)
2021-02-19 13:19:59 +01:00
Álvaro Fernández Rojas
a7c4d94342 bcm27xx: add diag LEDs
We can now use the power LED for diag in more devices thanks to the latest
patches from the RPi foundation.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry-picked from commit 5bab472a11)
2021-02-19 08:11:07 +01:00
Álvaro Fernández Rojas
9e2acdbccd bcm27xx: bcm2708: add missing RPi B DTS file
RPI 1B DTS has been splitted into 2 files:
 - bcm2708-rpi-b.dts: Newest (rev2) RPI 1B
 - bcm2708-rpi-b-rev1.dts: Old (rev1) RPI 1B

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry-picked from commit 0aaa2cce1c)
2021-02-19 08:10:32 +01:00
Álvaro Fernández Rojas
1c22b7a1f2 bcm27xx: add support for RPI CM4 and RPI 400
Support added to bcm2709 (32 bits) and bcm2711 (64 bits).

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry-picked from commit 8ad61118fd)
2021-02-19 07:19:46 +01:00
Álvaro Fernández Rojas
62b7f5931c bcm27xx: import latest patches from the RPi foundation
bcm2708: boot tested on RPi B+ v1.2
bcm2709: boot tested on RPi 3B v1.2 and RPi 4B v1.1 4G
bcm2710: boot tested on RPi 3B v1.2
bcm2711: boot tested on RPi 4B v1.1 4G

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry-picked from commit f07e572f64)
2021-02-19 07:17:21 +01:00
John Audia
76d1168d0d kernel: bump 5.4 to 5.4.99
Ran update_kernel.sh in a fresh clone without any existing toolchains.
No manual changes needed.

Build system: x86_64
Build-tested: bcm27xx/bcm2711

Signed-off-by: John Audia <graysky@archlinux.us>
(cherry-picked from commit 5d3a6fd970)
2021-02-19 07:15:59 +01:00
David Bauer
194e85e7db mediatek: add support for Ubiquiti UniFi 6 LR
Hardware
--------

MediaTek MT7622
512MB DDR3 RAM
64M SPI-NOR Flash (Winbond W25Q512JV)
MediaTek MT7622 802.11bgn 4T4R WMAC
MediaTek MT7915 802.11ax 4T4R
Marvell AQR1112 100/1000/2500 NBase-T PHY
Holtek HT32F52241 LED controller
Reset Switch

UART
----

CPU UART0 at the pinout next to the Holtek MCU.

Pinout (first pin next to SoC / MCU)

0 3V3
1 RX
2 TX
3 GND

Settings are 115200 8N1.

Opening the case
----------------

Opening the case is not a nice task, as itis glued together. Insert a
flat knife between the front and back casing below the ethernet port.
Open up a gap this way and insert a flat scredriver, remove the knife.

Work your way around the casing by applying force to seperate the front
and back casing. This losens the glue and opens the plastic clips. Be
gentle, as these clips are very cheap and break quickly.

Installation
------------

1. Connect to the booted device at 192.168.1.20 using username/password
   "ubnt".

2. Transfer the OpenWrt sysupgrade image to the device using SCP.

3. Check the mtd partition number for bs / kernel0 / kernel1

   $ cat /proc/mtd

4. Set the bootselect flag to boot from kernel0

   $ dd if=/dev/zero bs=1 count=1 of=/dev/mtdblock6

5. Write the OpenWrt sysupgrade image to both kernel0 as well as kernel1

   $ dd if=openwrt.bin of=/dev/mtdblock8
   $ dd if=openwrt.bin of=/dev/mtdblock9

6. Reboot the device. It should boot into OpenWrt.

Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 634c13c186)
2021-02-18 12:14:34 +01:00
David Bauer
ee6349fbe5 mediatek: add Ubiquiti LED driver
Add a driver for controlling the RGB LED via Ubiquitis own "LEDBAR" LED
controller based on the Holtek HT32F52241 MCU.

This driver is initially used by the Ubiquiti UniFi 6 LR, however
judging from FCC pictures the MCU is also found on the U6-Mesh as well
as the U6-Extender.

Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit c9137e2ddf)
2021-02-18 12:14:25 +01:00
Mathias Kresin
0011c7ad12 lantiq: fritz7320: enable USB power supply
The USB ports if a FRIZZ!Box 7320 do not supply power to connected
devices.

Add the GPIOs enabling USB power as regulator, to enable USB power
supply as soon as the USB driver is loaded.

Fixes FS#3624

Signed-off-by: Mathias Kresin <dev@kresin.me>
(cherry picked from commit 6e4e97b2256327bb380ee2a83da9a1ddf657e395)
2021-02-18 00:14:51 +01:00
Adrian Schmutzler
865cab8c6e kernel: 5.4: fix .patch file extension
File extension was truncated for
pending-5.4/770-11-net-ethernet-mtk_eth_soc-avoid-rearming-interrupt-if.pa

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 487b7ae5eb)
2021-02-17 01:32:28 +01:00
Adrian Schmutzler
b95f3caaa1 ipq807x: drop target
This target is not ready for stable release yet.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-16 14:00:58 +01:00
Rafał Miłecki
f0933303d6 bcm4908: fix GPIOs support by limiting them to 64
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-02-15 22:18:50 +01:00
Rafał Miłecki
da92e9825a bcm4908: use DTS patches sent upstream
There are 2 new patches:
1. Netgear R8000P switch ports
2. Netgear R8000P LEDs

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-02-15 22:18:45 +01:00
Rafał Miłecki
95359dac82 bcm4908: add USB packages to the DEFAULT_PACKAGES
All known 41 BCM4908 devices have USB ports so it makes sense to include
those packages by default.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-02-15 16:54:28 +01:00
Rafał Miłecki
26052fb355 bcm4908: fix backport of PMB driver
Missing Makefile change was preventing kernel from actually compiling
the driver.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-02-15 16:54:25 +01:00
Rafał Miłecki
09fbc79bf6 kernel: drop ofpart patch dropped from upstream mtd tree
It stopped ofpart_parser_init() from being called

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-02-15 15:06:40 +01:00
Rafał Miłecki
ac7d45b5e7 kernel: backport "ofpart" mtd parser upstream quirks support
This adds quirks support to the "ofpart" parser. It's required to
support fixed partitions that require some extra logic.

Right now only BCM4908 binding is supported (BCM4908 requires detecting
currently used "firmware" partition).

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-02-15 12:02:33 +01:00
Ilya Lipnitskiy
3da4acaa7b kernel: fix busy wait loop in mediatek PPE code
The intention is for the loop to timeout if the body does not succeed.
The current logic calls time_is_before_jiffies(timeout) which is false
until after the timeout, so the loop body never executes.

time_is_after_jiffies(timeout) will return true until timeout is less
than jiffies, which is the intended behavior here.

Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
2021-02-15 08:13:16 +01:00
Kurt Roeckx
539966554d ramips: mark toggle input on EX6150 as a switch
The Netgear EX6150 has an Access Point/Extender switch. Set it as
an EV_SW. Otherwise when it's set to Access Point, it will trigger
failsafe mode during boot.

Fixes: FS#3590
Signed-off-by: Kurt Roeckx <kurt@roeckx.be>
2021-02-15 00:00:38 +01:00
Petr Štetiar
0fde111702 Revert "imx6: bootscript-apalis: make it working on v2021.01 release"
This reverts commit 4968fc8fb1 as the bump
to v2021.01 needs swig on the host for pylibfdt which is needed by dtoc
tool to generate .h/.c files from DTBs in SPL for mx6cuboxi_config.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2021-02-14 23:28:07 +01:00
Paul Fertser
25d6af98d0 ath79: fix factory image generation for Netgear and Zyxel boards
The factory images need to embed specific IDs to pass verification with
the OEM firmware (including TFTP recovery), so they need to be
per-device variables.

Fixes: ab1584a797 ("ath79: netgear: trim down uImage customisations")
Fixes: 459c8c9ef8 ("ath79: add support for ZyXEL NBG6616")
Reported-by: Marcin Juszkiewicz <marcin-openwrt@juszkiewicz.com.pl>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
[minor commit message adjustments, sort DEVICE_VARS]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-14 19:21:38 +01:00
Tomasz Maciej Nowak
1caa81e505 mvebu: espressobin: drop COMPHY removement patch
There are proper workarounds merged to 5.4 stable tree for ESPRESSObin
boards with older bootloader:
4e1a23779bde ("ata: ahci: mvebu: Make SATA PHY optional for Armada 3720")
40af962eb1d4 ("usb: host: xhci: mvebu: make USB 3.0 PHY optional for
Armada 3720")

Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
2021-02-14 09:34:57 +01:00
Sander Vanheule
69551a2442 ramips: manage low reset lines
The bootloader of a number of recent TP-Link devices does not properly
initialise the MT7621's internal switch when booting from flash. To
enable the mt7530 driver to clear the reset on the switch, the ramips
reset controller must be allowed to toggle these.

Backport upstream commit 3f9ef7785a9c from mips-next to allow control of
the "mcm" reset line.

Signed-off-by: Sander Vanheule <sander@svanheule.net>
2021-02-14 09:33:42 +01:00
Petr Štetiar
4968fc8fb1 imx6: bootscript-apalis: make it working on v2021.01 release
Upstream in commit 8b9c0cb46471 ("apalis_imx6: boot env configuration
updates") removed emmc legacy wrappers, but so far didn't included any
replacements. Fix it by simply defining the missing variables and UUID
gathering directly into the boot script.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2021-02-14 09:31:30 +01:00
Adrian Schmutzler
a45953c2f2 bcm4908: refresh patches
Our patch refresh tool creates quite a big diff for these patches,
as it does not use rename syntax.

Push the refresh separately so it does not pollute the next kernel
bump. This is a purely cosmetic change.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-13 21:21:01 +01:00
Martin Kennedy
e2db870398 ath79: fix chip used for Meraki MR12 caldata_extract
The original setup fails to trigger ART calibration data
extraction for the AR9287. Instead, it would only have extracted
calibration data for an internal WMAC chip which is not present on
this board.

Fixes: 55d2db0e8c ("ath79: add support for Meraki MR12")

Signed-off-by: Martin Kennedy <hurricos@gmail.com>
[commit title/message facelift]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-13 21:21:01 +01:00
Stijn Segers
ad5e29d38a ramips: remove factory image for TP-Link Archer C2 v1
Initial commit 8375623a06 ("ramips: add support for TP-Link Archer
C2") contains detailed installation instructions, which do not mention
a factory image. From what I can see, no support to install OpenWrt
through the vendor web interface has been added since. The factory
image is also conspicuously absent from the device page in the wiki.
Yet, it is available for download.

I bricked my Archer C2 loading the factory image through the web UI.
Serial showed this error during bootloop:

  Uncompressing Kernel Image ... LZMA ERROR 1 - must RESET board to recover

This patch disables the undocumented factory image so users won't get
tricked into thinking easy web UI flashing actually works.

Signed-off-by: Stijn Segers <foss@volatilesystems.org>
2021-02-13 21:21:01 +01:00
Rafał Miłecki
d8afae0be8 bcm4908: fix handling Ethernet frames of size 1506 - 1514
MTU needs to be explicitly set as default value is too low.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-02-12 16:30:14 +01:00
Rafał Miłecki
87efff6329 bcm4908: use upstream accepted Ethernet driver patches
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-02-12 16:30:14 +01:00
Michael Mohr
8cbd6f5117 realtek: add support for Netgear GS108T v3
The Netgear GS108T v3 is an 8 port gigabit switch with PoE-PD support
on port 1.  The two prior versions were built using eCos and are not
currently compatible with OpenWRT.

The GS108T v3 is quite similar to both the GS110TPP v1 and GS110TP v3,
all of which use the same firmware image from Netgear.  For this reason,
the device tree is identical aside from the model and compatible values.

All of the above feature a dual firmware layout, referred to as Image0
and Image1 in the Netgear firmware.

Hardware specification
----------------------

 * RTL8380M SoC, 1 MIPS 4KEc core @ 500MHz
 * 128MB DDR3-1600 DRAM (Winbond W631GG8MB-12)
 * 32MB 3v NOR SPI Flash (Macronix MX25L25635F or Winbond W25Q256JVFIQ)
 * RTL8231 GPIO extender to control the LEDs and the reset button
 * 8 x 10/100/1000BASE-T ports, internal PHY (RTL8218B)
 * UART (115200 8N1) via unpopulated standard 0.1" pin header marked J1
 * Power is supplied via a 12V 1A barrel connector or 802.3af

UART pinout
-----------

J1 | [o]ooo
      ^ ||`------ GND
      | |`------- RX         [TX out of the serial adapter]
      | `-------- TX         [RX into the serial adapter]
      `---------- Vcc (3V3)  [the square pin]

The through holes are filled with PB-free solder which melts at 375C.
They can also be drilled using a 0.9mm bit.

Build configuration
-------------------

 * Target System: Realtek MIPS
 * Target Profile: Netgear GS108T v3
 * Target Images -> ramdisk -> Compression: lzma
 * Disable other target images

Boot initramfs image from U-Boot
--------------------------------

 1. Press the Escape key at the `Hit Esc key to stop autoboot` prompt
 2. Init network with `rtk network on` command
 3. Load image with `tftpboot 0x8f000000 openwrt-realtek-generic-netgear_gs108t-v3-initramfs-kernel.bin` command
 4. Boot the image with `bootm` command

The switch defaults to IP 192.168.1.1 and tries to fetch the image via
TFTP from 192.168.1.111.

Updating the installed firmware
-------------------------------

The OpenWRT ramdisk image can be flashed directly from the Netgear UI.
The Image0 slot should be used in order to enable sysupgrade.

As with similar switches, changing the active boot partition can be
accomplished in U-Boot as follows:

 1. Press the Escape key at the `Hit Esc key to stop autoboot` prompt
 2. Run `setsys bootpartition {0|1}` to select the boot partition
 3. Run `savesys` followed by `boota` to proceed with the boot process

Signed-off-by: Michael Mohr <akihana@gmail.com>
2021-02-12 08:52:41 +01:00
Michael Mohr
9fe90e4e5a realtek: refactor the Netgear GS110TPP v1 device tree
Move most of the GS110TPP v1 device tree into a dtsi so that it can be
shared with the GS108T v3.  Additionally:

  * Use macros to simplify the ethernet and switch definitions
  * Zero-pad the offsets and sizes in the partition map to 8 digits each

The spi-max-frequency value has been changed from 10MHz to 50MHz based
on an analysis of the relevant datasheets.  The current driver doesn't
use this property, as the clock speed is fixed. However, it's required
for this type of DT node, so that's why it's present here.

The firmware partition has been split in half, since this is how the
stock firmware uses it.  This can be used to easily revert to a stock
firmware if one is written to the second image area.

Signed-off-by: Michael Mohr <akihana@gmail.com>
2021-02-12 08:52:41 +01:00
Michael Mohr
9877393fd1 realtek: add and use netgear_nge for the GS110PP v1
The netgear_nge device will be shared between the GS108T v3 (to be added
in a later commit) and the GS110PP v1.  It also enables LZMA compression
for the ramdisk image.

Signed-off-by: Michael Mohr <akihana@gmail.com>
2021-02-12 08:52:41 +01:00
Adrian Schmutzler
6934d30cf8 ath79: fix USB power GPIO for TP-Link TL-WR810N v1
The TP-Link TL-WR810N v1 is known to cause soft-brick on ath79 and
work fine for ar71xx [1]. On closer inspection, the only apparent
difference is the GPIO used for the USB regulator, which deviates
between the two targets.

This applies the value from ar71xx to ath79.

Tested successfully by a forum user.

[1] https://forum.openwrt.org/t/tp-link-tl-wr810n-v1-ath79/48267

Fixes: cdbf2de777 ("ath79: Add support for TP-Link WR810N")
Fixes: FS#3522

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-11 23:58:32 +01:00
INAGAKI Hiroshi
08768b44d9 ramips: add support for ELECOM WRC-1167FS
ELECOM WRC-1167FS is a 2.4/5 GHz band 11ac (WiFi-5) router, based on
MT7628AN.

Specification:

- SoC		: MediaTek MT7628AN
- RAM		: DDR2 64 MiB (NT5TU32M16FG-AC)
- Flash		: SPI-NOR 16 MiB (W25Q128JVSIQ)
- WLAN		: 2.4/5 GHz 2T2R
  - 2.4 GHz	: MediaTek MT7628AN (SoC)
  - 5 GHz	: MediaTek MT7612E
- Ethernet	: 10/100 Mbps x2
  - Switch	: MT7628AN (SoC)
- LEDs/Keys	: 6x, 3x (2x buttons, 1x slide-switch)
- UART		: through-hole on PCB
  - J1: 3.3V, GND, TX, RX from "J1" marking
  - 57600n8
- Power		: 12 VDC, 1 A

Flash instruction using factory image:

1. Boot WRC-1167FS normally
2. Access to "http://192.168.2.1/" and open firmware update page
   ("ファームウェア更新")
3. Select the OpenWrt factory image and click apply ("適用") button to
   perform firmware update
4. Wait ~120 seconds to complete flashing

Notes:

- Last 0x800000 (8 MiB) in SPI-NOR flash is not used on stock firmware

- Additional padding in factory image is required to avoid incomplete
  flashing on stock firmware

MAC addresses:

- LAN	: BC:5C:4C:xx:xx:68 (Config, ethaddr (text) / Factory, 0x28   (hex))
- WAN	: BC:5C:4C:xx:xx:69 (Config, wanaddr (text) / Factory, 0x22   (hex))
- 2.4GHz: BC:5C:4C:xx:xx:6A (Config, rmac    (text) / Factory, 0x4    (hex))
- 5GHz	: BC:5C:4C:xx:xx:6B (Config, rmac2   (text) / Factory, 0x8004 (hex))

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2021-02-11 16:37:53 +01:00
John Audia
e95b1b23f1 kernel: bump 5.4 to 5.4.97
Ran update_kernel.sh in a fresh clone without any existing toolchains.

Manually rebased:
 bcm27xx
  950-0267-xhci-add-quirk-for-host-controllers-that-don-t-updat.patch
 bcm53xx
  180-usb-xhci-add-support-for-performing-fake-doorbell.patch
 layerscape
  302-dts-0008-arm64-dts-ls1046a-accumulated-change-to-ls1046a-boar.patch
  820-usb-0016-MLK-16735-usb-host-add-XHCI_CDNS_HOST-flag.patch
  820-usb-0018-MLK-18794-1-usb-host-xhci-add-.bus_suspend-override.patch

Build system: x86_64
Build-tested: bcm27xx/bcm2711, ipq806x/R7800
Run-tested: ipq806x/R7800

No dmesg regressions/everything functional.

Signed-off-by: John Audia <graysky@archlinux.us>
[remove quilt comment, fix/adjust 820-usb-* layerscape patches]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-11 16:08:28 +01:00
Adrian Schmutzler
3cc08b5702 at91: use SPDX license identifiers on DTS files
Use SPDX license tags to allow machines to check licenses.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-10 15:47:23 +01:00
Adrian Schmutzler
7157c77c6d target: use SPDX license identifiers on scripts
Use SPDX license tags to allow machines to check licenses.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-10 15:47:23 +01:00
Adrian Schmutzler
598b29585e target: use SPDX license identifiers on Makefiles
Use SPDX license tags to allow machines to check licenses.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-10 15:47:18 +01:00
Rafał Miłecki
c382fe857d bcm4908: update Ethernet driver
Use the latest version sent upsteram.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-02-10 11:28:04 +01:00
Andrew Pikler
cd2b661453 ramips: add support for Cudy WR1300
Specifications:
 - SoC: MediaTek MT7621AT
 - RAM: 128 MB (DDR3)
 - Flash: 16 MB (SPI NOR)
 - WiFi: MediaTek MT7603E, MediaTek MT7612E
 - Switch: 1 WAN, 4 LAN (Gigabit)
 - Ports: 1 USB 3.0
 - Buttons: Reset, WPS
 - LEDs: Power, System, Wan, Lan 1-4, WiFi 2.4G, WiFi 5G, WPS, USB
 - Power: DC 12V 1A tip positive

UART Serial:
  115200 baud
  Located on unpopulated 4 pin header near J4:

  J4
  [o] Rx
  [o] Tx
  [o] GND
  [ ] Vcc - Do not connect

Installation:

Download and flash the manufacturer's built OpenWRT image available at
http://www.cudytech.com/openwrt_software_download
Install the new OpenWRT image via luci (System -> Backup/Flash firmware)
Be sure to NOT keep settings. The force upgrade may need to be checked
due to differences in router naming conventions.

Recovery:
 - Loads only signed manufacture firmware due to bootloader RSA verification
 - serve tftp-recovery image as /recovery.bin on 192.168.1.88/24
 - connect to any lan ethernet port
 - power on the device while holding the reset button
 - wait at least 8 seconds before releasing reset button for image to
   download
 - See http://www.cudytech.com/newsinfo/547425.html

MAC addresses as verified by OEM firmware:

use   address   source
LAN   *:f0      label
WAN   *:f1      label + 1
2g    *:f0      label
5g    *:f2      label + 2

The label MAC address is found in bdinfo 0xde00.

Signed-off-by: Andrew Pikler <andrew.pikler@gmail.com>
2021-02-09 13:58:18 +01:00
Sebastian Schaper
dc4745da7a ath79: add support for D-Link DAP-3662 A1
Specifications:
 * QCA9557, 16 MiB Flash, 128 MiB RAM, 802.11n 2T2R
 * QCA9882, 802.11ac 2T2R
 * 2x Gigabit LAN (1x 802.11af PoE)
 * IP68 pole-mountable outdoor case

Installation:
 * Factory Web UI is at 192.168.0.50
   login with 'admin' and blank password, flash factory.bin
 * Recovery Web UI is at 192.168.0.50
   connect network cable, hold reset button during power-on and keep it
   pressed until uploading has started (only required when checksum is ok,
   e.g. for reverting back to oem firmware), flash factory.bin

After flashing factory.bin, additional free space can be reclaimed by
flashing sysupgrade.bin, since the factory image requires some padding
to be accepted for upgrading via OEM Web UI.

Both ethernet ports are set to LAN by default, matching the labelling on
the case. However, since both GMAC Interfaces eth0 and eth1 are connected
to the switch (QCA8337), the user may create an additional 'wan' interface
as desired and override the vlan id settings to map br-lan / wan to either
the PoE or non-PoE port, depending on the individual scenario of use.

So, the LAN and WAN ports would then be connected to different GMACs, e.g.

config interface 'lan'
	option ifname 'eth0.1'
	...

config interface 'wan'
	option ifname 'eth1.2'
	...

config switch_vlan
        option device 'switch0'
        option vlan '1'
        option ports '1 0t'

config switch_vlan
        option device 'switch0'
        option vlan '2'
        option ports '2 6t'

Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
[add configuration example]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-09 13:10:33 +01:00
Chukun Pan
82032f3509 ramips: add support for JCG Y2
JCG Y2 is an AC1300M router

Hardware specs:
  SoC: MediaTek MT7621AT
  Flash: Winbond W25Q128JVSQ 16MiB
  RAM: Nanya NT5CB128M16 256MiB
  WLAN: 2.4/5 GHz 2T2R (1x MediaTek MT7615)
  Ethernet: 10/100/1000 Mbps x5
  LED: POWER, INTERNET, 2.4G, 5G
  Button: Reset
  Power: DC 12V,1A

Flash instructions:
  Upload factory.bin in stock firmware's upgrade page.

MAC addresses map:
  0x0004  *:c8  wlan2g/wlan5g/label
  0xe000  *:c7  lan
  0xe006  *:c6  wan

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
2021-02-09 13:10:33 +01:00
Michael Pratt
f5f01bcacd ath79: use internal switch for EAP300 v2
Have the port use GMAC1 with internal switch
which fixes the issue of the ethernet LED not functioning
The LED is triggered by the internal switch, not a GPIO.

The GPIO for the ethernet LED was added in ath79
as it was defined in the ar71xx target
but it was not functioning in ath79 for a previously unknown reason.

It is unknown why that GPIO was defined as an LED in ar71xx.

Signed-off-by: Michael Pratt <mcpratt@pm.me>
[drop unrelated changes: model property and SPI max frequency]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-08 16:34:18 +01:00
Michael Pratt
88079bd616 ath79: make all eth ports LAN for Engenius APs
for:
 - ENH202 v1
 - ENS202EXT v1
 - EnstationAC v1
 - EWS511AP

For EWS511AP, have default behavior as static ip
to match the behavior of all other APs in ath79

These boards are sold as
Client Bridge or Point to Point or Access Point
so there is probably no benefit to have WAN by default
for one of the ports, to prevent user confusion.

Signed-off-by: Michael Pratt <mcpratt@pm.me>
2021-02-08 16:34:18 +01:00
John Audia
f3b827a965 kernel: bump 5.4 to 5.4.96
Ran update_kernel.sh in a fresh clone without any existing toolchains.

Build system: x86_64
Build-tested: ipq806x/R7800, bcm27xx/bcm2711
Run-tested: ipq806x/R7800
Run-tested [*]: ramips/mt7621 (R6800, DIR-878 A1, EAP235-Wall)

Signed-off-by: John Audia <graysky@archlinux.us>
Tested-by: Stijn Segers <foss@volatilesystems.org> [*]
2021-02-08 16:34:18 +01:00
Rafał Miłecki
f06c3031a7 bcm4908: add board.d network setup
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-02-08 12:05:56 +01:00
Rafał Miłecki
81240a9b89 bcm4908: add Ethernet driver
This commit picks up pending netdev patches.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-02-08 11:49:21 +01:00
Szabolcs Hubai
1e9afcca56 ramips: disable default build for HooToo HT-TM02
While the latest version of 19.07 release is usable,
the current master is unbootable on the device in a normal way.

"Normal way" installations includes:
- sysupgrade (e.g. from 19.07)
- RESET button recovery with Ron Curry's (Wingspinner) UBoot image
  (10.10.10.3 + "Kernal.bin")
- RESET button recovery with original U-Boot
  (10.10.10.254 + "kernel")

One could flash and boot the latest master sysupgrade image successfully
with serial access to the device. But a sysupgrade from this state still
breaks the U-Boot and soft-bricks the device.

Signed-off-by: Szabolcs Hubai <szab.hu@gmail.com>
2021-02-07 22:06:57 +01:00
Adrian Schmutzler
1c0e13db43 ramips: mt7621: use preferred logic in lib/upgrade/iodata.sh
shellcheck recommends || and && over "-a" and "-o" because the
latter are not well defined.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-07 21:58:51 +01:00
INAGAKI Hiroshi
88fbddb49d ramips: add support for I-O DATA WN-DX1200GR
I-O DATA WN-DX1200GR is a 2.4/5 GHz band 11ac (WiFi-5) router, based on
MT7621A.

Specification:

- SoC		: MediaTek MT7621A
- RAM		: DDR3 128 MiB
- Flash		: raw NAND 128 MiB
- WLAN		: 2.4/5 GHz 2T2R
  - 2.4 GHz	: MediaTek MT7603E
  - 5 GHz	: MediaTek MT7613BE
- Ethernet	: 10/100/1000 Mbps x5
  - Switch	: MediaTek MT7530 (SoC)
- LEDs/keys	: 2x/3x (2x buttons, 1x slide-switch)
- UART		: through-hole on PCB
  - J5: 3.3V, TX, RX, NC, GND from triangle-mark
  - 57600n8
- Power		: 12 VDC, 1 A

Flash instruction using initramfs image:

1. Boot WN-DX1200GR normally
2. Access to "http://192.168.0.1/" and open firmware update page
   ("ファームウェア")
3. Select the OpenWrt initramfs image and click update ("更新") button
   to perform firmware update
4. On the initramfs image, perform sysupgrade with the
   squashfs-sysupgrade image
5. Wait ~120 seconds to complete flashing

Notes:

- currently, mt7615e driver in mt76 doesn't fully support MT7613
  (MT7663) wifi chip
  - the eeprom data in flash is not used by mt7615e driver and the
    driver reports the tx-power up to 3dBm
  - the correct MAC address for MT7613BE in eeprom data cannot be
    assigned to the phy

- last 0x80000 (512 KiB) in NAND flash is not used on stock firmware

- stock firmware requires "customized uImage header" (called as "combo
  image") by MSTC (MitraStar Technology Corp.), but U-Boot doesn't

  - uImage magic ( 0x0 - 0x3 ) : 0x434F4D43 ("COMC")
  - header crc32 ( 0x4 - 0x7 ) : with "data length" and "data crc32"
  - image name   (0x20 - 0x37) : model ID and firmware versions
  - data length  (0x38 - 0x3b) : kernel + rootfs
  - data crc32   (0x3c - 0x3f) : kernel + rootfs

MAC addresses:

LAN:	50:41:B9:xx:xx:08 (Ubootenv, ethaddr (text) / Factory, 0x1E000 (hex))
WAN:	50:41:B9:xx:xx:0A (Factory,  0x1E006 (hex))
2.4GHz:	50:41:B9:xx:xx:08 (Factory,  0x4     (hex))
5GHz:	50:41:B9:xx:xx:09 (Factory,  0x8004  (hex))

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
[add check whether dflag_offset is set]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-07 21:58:51 +01:00
Daniel González Cabanelas
07f4e3b5b2 bcm63xx: kernel: reenable the TRNG
The hardware random number generator driver for bcm63xx was merged with
the one used by the Raspberry Pi. Now this driver is lost.

Reenable the HW_RANDOM kernel config with the new driver.

Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
[refresh kernel config]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2021-02-07 19:06:52 +01:00
Pawel Dembicki
17fa01bb79 mpc85xx: refresh kernel config
Simple "make kernel_oldconfig" was done.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2021-02-06 17:13:33 +01:00
Thomas Beckler
450ec48d61 kirkwood: use 3 temperature sensors for Zyxel NSA310B
Instead of taking the input of one temperature sensor (temp1), the
script takes into account three temperature sensors to control the
PWM of the cooling fan.

temp1 -> placed on main board
temp2 -> placed on main board
temp3 -> placed on or close to chipset

All three temperatures give valid input for the PWM of the fan on
NSA310 and are actually changing.

Tested on two NSA310.

Signed-off-by: Thomas Beckler <thomas.beckler@hotmail.com>
Reviewed-by: Alberto Bursi <bobafetthotmail@gmail.com>
[commit title/message facelift, code cleanup]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-05 22:21:08 +01:00
Adrian Schmutzler
8a79161a82 ath79: wrap ucidef_add_switch in 02_network
Wrap line to be consistent with all other definitions.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-05 21:57:19 +01:00
Yanase Yuki
d468ff97b7 build: move elx-header into image-commands.mk
ELECOM WAB-I1750-PS will need this in ath79, so move it to common
Makefile.

Signed-off-by: Yanase Yuki <dev@zpc.sakura.ne.jp>
2021-02-05 21:57:19 +01:00
Sungbo Eo
321035420c kirkwood: refresh kernel config
Refresh config with make kernel_oldconfig.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2021-02-05 19:05:20 +01:00
Aleksander Jan Bajkowski
c9619fe6a5 lantiq: change phy-mode to mii for FRITZ!Box 7412
FRITZ!Box 7412 loads the firmware for fast ethernet PHY and mii is
more accurate in this case.
Gmii is used by Gigabit ethernet PHYs.

Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
Reviewed-by: Mathias Kresin <dev@kresin.me>
[minor commit title/message adjustments]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-05 18:56:19 +01:00
Adrian Schmutzler
04a0e5c082 ipq806x: replace full-text BSC license by SPDX identifier
This replaces a full-text BSD clause by the corresponding SPDX
identifier.

This should make it easier to identify the license both by humans
and machines.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-05 18:28:30 +01:00
Adrian Schmutzler
3f4d1dad00 ramips: replace full-text licenses by SPDX identifier
This replaces several full-text and abbreviated licenses found in
DTS files by the corresponding SPDX identifiers.

This should make it easier to identify the license both by humans
and machines.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-05 18:18:00 +01:00
David Bentham
4a18039785 ramips: add support for UniElec U7621-01
UniElec U7621-01 is a router platform board, the smaller model of
the U7621-06.
The device has the following specifications:

- MT7621AT (880 MHz)
- 256 of RAM (DDR3)
- 16 MB of FLASH (SPI NOR)
- 5x 1 Gbps Ethernet (MT7621 built-in switch)
- 1x 2.4Ghz MT7603E
- 1x 5Ghz MT7612
- 1x miniPCIe slots (PCIe bus only)
- 1x miniSIM slot
- 1x USB 2.0 (uses the usb 3.0 driver)
- 8x LEDs (1x GPIO-controlled)
- 1x reset button
- 1x UART header (4-pins)
- 1x GPIO header (30-pins)
- 1x DC jack for main power (12 V)

The following has been tested and is working:

- Ethernet switch
- 1x 2.4Ghz MT7603E (wifi)
- 1x 5Ghz MT7612 (wifi)
- miniPCIe slots (tested with Wi-Fi cards and LTE modem cards)
- miniSIM slot (works with normal size simcard)
- sysupgrade
- reset button

Installation:

This board has no locked down bootloader. The seller can be asked to
install openwrt v18.06, so upgrades are standard sysupgrade method.

Recovery:

This board contains a Chinese, closed-source bootloader called Breed
(Boot and Recovery Environment for Embedded Devices). Breed supports web
recovery and to enter it, you keep the reset button pressed for around
5 seconds during boot. Your machine will be assigned an IP through DHCP
and the router will use IP address 192.168.1.1. The recovery website is
in Chinese, but is easy to use. Click on the second item in the list to
access the recovery page, then the second item on the next page is where
you select the firmware. In order to start the recovery, you click the
button at the bottom.

LEDs list (left to right):

- ESW_P0_LED_0
- ESW_P1_LED_0
- ESW_P2_LED_0
- ESW_P3_LED_0
- ESW_P4_LED_0
- CTS2_N (GPIO10, configured as "status" LED)
- LED_WLAN# (connected with pin 44 in wifi1 slot)

Signed-off-by: David Bentham <db260179@gmail.com>
[add DEVICE_VARIANT, fix DEVICE_PACKAGES, remove &gpio]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-05 17:31:51 +01:00
Martin Kennedy
55d2db0e8c ath79: add support for Meraki MR12
Port device support for Meraki MR12 from the ar71xx target to ath79.

Specifications:

  - SoC: AR7242-AH1A CPU
  - RAM: 64MiB (NANYA NT5DS32M16DS-5T)
  - NOR Flash: 16MiB (MXIC MX25L12845EMI-10G)
  - Ethernet: 1 x PoE Gigabit Ethernet Port (SoC MAC + AR8021-BL1E PHY)
  - Ethernet: 1 x 100Mbit port (SoC MAC+PHY)
  - Wi-Fi: Atheros AR9283-AL1A (2T2R, 11n)

Installation:

  1. Requires TFTP server at 192.168.1.101, w/ initramfs & sysupgrade .bins
  2. Open shell case
  3. Connect a USB->TTL cable to headers furthest from the RF shield
  4. Power on the router; connect to U-boot over 115200-baud connection
  5. Interrupt U-boot process to boot Openwrt by running:
       setenv bootcmd bootm 0xbf0a0000; saveenv;
       tftpboot 0c00000 <filename-of-initramfs-kernel>.bin;
       bootm 0c00000;
  6. Copy sysupgrade image to /tmp on MR12
  7. sysupgrade /tmp/<filename-of-sysupgrade>.bin

Notes:

  - kmod-owl-loader is still required to load the ART partition into the
    driver.

  - The manner of storing MAC addresses is updated from ar71xx; it is
    at 0x66 of the 'config' partition, where it was discovered that the
    OEM firmware stores it. This is set as read-only. If you are
    migrating from ar71xx and used the method mentioned above to
    upgrade, use kmod-mtd-rw or UCI to add the MAC back in. One more
    method for doing this is described below.

  - Migrating directly from ar71xx has not been thoroughly tested, but
    one method has been used a couple of times with good success,
    migrating 18.06.2 to a full image produced as of this commit. Please
    note that these instructions are only for experienced users, and/or
    those still able to open their device up to flash it via the serial
    headers should anything go wrong.

    1) Install kmod-mtd-rw and uboot-envtools
    2) Run `insmod mtd-rw.ko i_want_a_brick=1`
    3) Modify /etc/fw_env.config to point to the u-boot-env partition.
       The file /etc/fw_env.config should contain:

       # MTD device   env offset  env size    sector size
       /dev/mtd1      0x00000     0x10000     0x10000

       See https://openwrt.org/docs/techref/bootloader/uboot.config
       for more details.

    4) Run `fw_printenv` to verify everything is correct, as per the
       link above.
    5) Run `fw_setenv bootcmd bootm 0xbf0a0000` to set a new boot address.
    6) Manually modify /lib/upgrade/common.sh's get_image function:
       Change ...

       cat "$from" 2>/dev/null | $cmd

       ... into ...

       (
         dd if=/dev/zero bs=1 count=$((0x66)) ; # Pad the first 102 bytes
         echo -ne '\x00\x18\x0a\x12\x34\x56'  ; # Add in MAC address
         dd if=/dev/zero bs=1 count=$((0x20000-0x66-0x6)) ; # Pad the rest
         cat "$from" 2>/dev/null
       ) | $cmd

       ... which, during the upgrade process, will pad the image by
       128K of zeroes-plus-MAC-address, in order for the ar71xx's
       firmware partition -- which starts at 0xbf080000 -- to be
       instead aligned with the ath79 firmware partition, which
       starts 128K later at 0xbf0a0000.

    7) Copy the sysupgrade image into /tmp, as above
    8) Run `sysupgrade -F /tmp/<sysupgrade>.bin`, then wait

    Again, this may BRICK YOUR DEVICE, so make *sure* to have your
    serial cable handy.

Signed-off-by: Martin Kennedy <hurricos@gmail.com>
[add LED migration and extend compat message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-05 16:56:08 +01:00
Ewan Parker
ddafcc7947 ramips: add support for Hi-Link HLK-7688A
Specifications:

  - SoC: MediaTek MT7688AN
  - RAM: 128 MB
  - Flash: 32 MB
  - Ethernet: 5x 10/100 (1x WAN, 4x LAN)
  - Wireless: built in 2.4GHz (bgn)
  - USB: 1x USB 2.0 port
  - Buttons: 1x Reset
  - LEDs: 1x (WiFi)

Flash instructions:

  - Configure TFTP server with IP address 10.10.10.3
  - Name the firmware file as firmware.bin
  - Connect any Ethernet port to the TFTP server's LAN
  - Choose option 2 in U-Boot
  - Alternatively choose option 7 to upload firmware to the built-in
    web server

MAC addresses as verified by OEM firmware:

  use   address   source
  2g    *:XX      factory 0x4
  LAN   *:XX+1    factory 0x28
  WAN   *:XX+1    factory 0x2e

Notes:

This board is ostensibly a module containing the MediaTek MT7688AN SoC,
128 MB DDR2 SDRAM and 32 MB flash storage.  The SoC can be operated in
IoT Gateway Mode or IoT Device Mode.

From some vendors the U-Boot that comes installed operates on UART 2
which is inaccessible in gateway mode and operates unreliably in the
Linux kernel when using more than 64 MB of RAM.  For those, updating
U-Boot is recommended.

Signed-off-by: Ewan Parker <ewan@ewan.cc>
[add WLAN to 01_leds]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-05 14:54:47 +01:00
John Audia
36c9cf3e51 kernel: bump 5.4 to 5.4.95
Ran update_kernel.sh in a fresh clone without any existing toolchains.

Removed upstreamed patches:
 imx6: 303-ARM-dts-imx6qdl-gw52xx-fix-duplicate-regulator-namin.patch

Build system: x86_64
Build-tested: ipq806x/R7800, bcm27xx/bcm2711
Run-tested: ipq806x/R7800

No dmesg regressions, everything functional

Signed-off-by: John Audia <graysky@archlinux.us>
2021-02-04 22:07:32 +01:00
Daniel González Cabanelas
a0e0e621ca bcm63xx: sprom: override the PCI device ID
The PCI device ID detected by the wifi drivers on devices using a fallback
SPROM is wrong. Currently the chipnum is used for this parameter.

Most SSB based Broadcom wifi chips are 2.4 and 5GHz capable. But on
devices without a physical SPROM, the only one way to detect if the device
suports both bands or only the 5GHz band, is by reading the device ID from
the fallback SPROM.

In some devices, this may lead to a non working wifi on a 5GHz-only card,
or in the best case a working 2.4GHz-only in a dual band wifi card.

The offset for the deviceid in SSB SPROMs is 0x0008, whereas in BCMA is
0x0060. This is true for any SPROM version.

Override the PCI device ID with the one defined at the fallback SPROM, to
detect the correct wifi card model and allow using the 5GHz band if
supported.

The patch has been tested with the following wifi radios:

BCM43222: b43: both 2.4/5GHz working
          brcm-wl: both 2.4/5GHz working

BCM43225: b43: 2.4GHz, working
	 brcmsmac: working
	 brcm-wl: it lacks support

BCM43217: b43: 2.4GHz, working
	 brcmsmac: it lacks support
	 brcm-wl: it lacks support

Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
[amend commit description, rework patch to avoid using a new global variable
and keep ssb sprom extraction code as close to ssb/pci.c as possible]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2021-02-02 20:40:31 +01:00
Álvaro Fernández Rojas
e23a90674e bcm63xx: backport upstream SSB SPROM extraction
New upstream changes extract more SPROM values and fix the antenna gain.
These changes can be found in linux drivers/ssb/pci.c.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2021-02-02 20:40:29 +01:00
John Audia
d33cd383ed kernel: bump 5.4 to 5.4.94
All modification made by update_kernel.sh in a fresh clone without
existing toolchains.

Build-tested: bcm27xx/bcm2711, ipq806x/R7800,
Run-tested: ipq806x/R7800

No dmesg regressions, everything functional

Signed-off-by: John Audia <graysky@archlinux.us>
2021-02-01 19:10:43 +01:00
Leon Leijssen
eff03cea27 ath79: ag71xx: add ethtool statistics support
Add statistics to ethtool. The statistics can be useful to
debug network issues.

The code is backported from mainline ag71xx.c driver.

Signed-off-by: Leon Leijssen <leon.git@leijssen.info>
2021-02-01 00:48:12 +01:00
David Bauer
51f578efa5 ath79: add support for Ubiquiti UniFi AP Outdoor+
Hardware
--------
Atheros AR7241
16M SPI-NOR
64M DDR2
Atheros AR9283 2T2R b/g/n
2x Fast Ethernet (built-in)

Installation
------------

Transfer the Firmware update to the device using SCP.

Install using fwupdate.real -m <openwrt.bin> -d

Signed-off-by: David Bauer <mail@david-bauer.net>
2021-02-01 00:47:46 +01:00
David Bauer
0c499f6068 mac80211: convert UniFi Outdoor+ HSR support to OF
Enable support for the Ubiquiti UniFi Outdoor+ RF filter via
device-tree. The old way of using platform data is not required anymore,
as it was only used on the now removed ar71xx target.

Signed-off-by: David Bauer <mail@david-bauer.net>
2021-02-01 00:47:36 +01:00
Petr Štetiar
337ff74894 mvebu: omnia: make initramfs image usable out of the box
Currently it's not possible to boot the device with just initramfs image
without additional effort as the initramfs image doesn't contain device
tree.  Fix it by producing FIT based image which could be booted with
following commands:

 setenv bootargs earlyprintk console=ttyS0,115200
 tftpboot ${kernel_addr_r} openwrt-mvebu-cortexa9-cznic_turris-omnia-initramfs-kernel.bin
 bootm ${kernel_addr_r}

Acked-by: Klaus Kudielka <klaus.kudielka@gmail.com>
Reviewed-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2021-01-31 11:39:19 +01:00
Daniel González Cabanelas
24b910dca2 mvebu: LS421DE: fix the thermal zones
The thermal zones kernel documentation is misleading, we cannot use more
than one sensor in a thermal zone node.

Furthermore the drivetemp driver for some reason it only catches one
sensor from the hard drives array (the first available).

In the Buffalo Linkstation LS421DE board there is also a sensor at the
ethernet phy chip that can also be monitored. Very useful to stop the fan
when there are no hard drives in the bays.

(It might be also possible to add the CPU sensor, but it requires kernel
patching for registering the sensor via device tree, using the function:
devm_thermal_zone_of_sensor_register)

Fix the thermal zones to use only one sensor per node and add the ethernet
phy sensor. Also adjust the hdd temperatures to be more conservative for
a mechanical hard drive.

Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
2021-01-30 01:03:00 +01:00
INAGAKI Hiroshi
eb11cd9ea3 ramips: add support for ELECOM WRC-2533GHBK-I
ELECOM WRC-2533GHBK-I is a 2.4/5 GHz band 11ac (Wi-Fi 5) router, based
on MT7621A.

Specification:

- SoC		: MediaTek MT7621A
- RAM		: DDR3 128 MiB
- Flash		: SPI-NOR 16 MiB
- WLAN		: 2.4/5 GHz 4T4R (2x MediaTek MT7615)
- Ethernet	: 10/100/1000 Mbps x5
  - Switch	: MediaTek MT7530 (SoC)
- LED/keys	: 4x/3x (2x buttons, 1x slide-switch)
- UART		: through-hole on PCB
  - J4: 3.3V, RX, GND, TX from SoC side
  - 57600n8
- Power		: 12VDC, 1.5A

Flash instruction using factory image:

1. Boot WRC-2533GHBK-I normally
2. Access to "http://192.168.2.1/" and open firmware update page
   ("ファームウェア更新")
3. Select the OpenWrt factory image and click apply ("適用") button
4. Wait ~150 seconds to complete flashing

MAC addresses:

LAN	: BC:5C:4C:xx:xx:89 (Config, ethaddr (text))
WAN	: BC:5C:4C:xx:xx:88 (Config, wanaddr (text))
2.4GHz	: BC:5C:4C:xx:xx:8A (Factory, 0x4    (hex))
5GHz	: BC:5C:4C:xx:xx:8B (Factory, 0x8004 (hex))

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Reviewed-by: Sungbo Eo <mans0n@gorani.run>
2021-01-29 15:32:07 +01:00
INAGAKI Hiroshi
0071c7cd82 build: add elecom-product-header for ELECOM devices
A header used in ELECOM WRC-300GHBK2-I and WRC-1750GHBK2-I/C is also
used in ELECOM WRC-2533GHBK-I, so split the code to generate the header
and move it to image-commands.mk to use from ramips target.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Reviewed-by: Sungbo Eo <mans0n@gorani.run>
2021-01-29 15:28:12 +01:00
Adrian Schmutzler
331892f85f treewide: drop shebang from non-executable lib files
This drops the shebang from another bunch of files in various /lib
folders, as these are sourced and the shebang is useless.

Fix execute bit in one case, too.

This should cover almost all trivial cases now, i.e. where /lib is
actually used for library files.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-01-29 14:29:41 +01:00
John Audia
2c35899d81 kernel: bump 5.4 to 5.4.93
All modification made by update_kernel.sh in a fresh clone without
existing toolchains.

Build system:       x86_64
Build-tested:       ipq806x/R7800, bcm27xx/bcm2711
Run-tested:         ipq806x/R7800
Compile-tested [*]: ath79/{tiny,generic}, ipq40xx, octeon,
                    ramips/mt7621, realtek, x86/64
Run-tested [*]:     ath79/generic, ipq40xx, octeon, ramips/mt7621

No dmesg regressions, everything functional

Signed-off-by: John Audia <graysky@archlinux.us>
Tested-by: Stijn Segers <foss@volatilesystems.org> [*]
2021-01-29 14:22:09 +01:00
Álvaro Fernández Rojas
7d12f29ae1 bcm63xx: fix bcm63xx ethernet kernel panics
Calling netdev_reset_queue() from _stop() functions is causing sporadic kernel
panics on bcm63xx, which happen mainly on BCM6318 and BCM6328.
This reverts to the previous behaviour, which called netdev_reset_queue() from
_open() functions.

Tested on Comtrend AR-5315u (BCM6318).

Fixes: 1d6f422e34 ("bcm63xx: sync ethernet driver with net-next")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2021-01-28 12:01:14 +01:00
Jiang Yongquan
799fca7602 sunxi: add support for linksprite pcDuino3 nano board
Specifications:

 - SoC: Allwinner A20 @ 1Ghz
 - DRAM: 1GiB DDR3 @ 408MHz (K4B4G1646Q-HYK0)
 - NAND: 4GB MLC NAND (H27UBG8T2BTR-BC)
 - Ethernet: 10/100/1000Mbps Ethernet (Realtek RTL8211E)

Flash instructions:

dd if=openwrt-sunxi-cortexa7-linksprite_pcduino3-nano-ext4-sdcard.img
of=/dev/sdX

Signed-off-by: Jiang Yongquan <woxwchc@foxmail.com>
[Remove CONFIG_REALTEK_PHY from sunxi/cortexa53 config]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2021-01-27 23:14:30 +01:00
Marty Jones
9c29165a4c rockchip: fix SUPPORTED_DEVICES for Radxa ROCK Pi 4
This sets SUPPORTED_DEVICES to match the compatible in the DTS.

While at it, synchronize the capitalization in DEVICE_MODEL and
DTS model.

Signed-off-by: Marty Jones <mj8263788@gmail.com>
[commit title/message facelift, move variable in armv8.mk]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-01-27 21:31:20 +01:00
Adrian Schmutzler
30651e6834 bcm4908: sort and wrap build recipes
This sorts the Build recipes alphabetically, wraps some long lines
and moves the DEVICE_VARS to the top like common on several other
targets.

Cc: Rafał Miłecki <rafal@milecki.pl>

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-01-27 21:31:20 +01:00
Adrian Schmutzler
44f2d71edd mediatek: remove generic profiles
We have support for reference boards available on this target, so
support for an additional generic profile does not make much sense.

Remove it to have one thing less to maintain.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Paul Spooren <mail@aparcar.org>
2021-01-27 21:31:20 +01:00