Commit Graph

577 Commits

Author SHA1 Message Date
Koen Vandeputte
4465b44fc1 kernel: bump 4.14 to 4.14.219
Refreshed all patches.

Compile-tested on: ar71xx, cns3xxx, imx6, x86_64
Runtime-tested on: ar71xx, cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2021-02-05 09:30:47 +01:00
Hauke Mehrtens
c9388fa986 kernel: bump 4.14 to 4.14.214
Refreshed all patches.

Removed patches because included in upstream:
- 499-mtd-parser-cmdline-Fix-parsing-of-part-names-with-co.patch
- 0071-2-PCI-qcom-Fixed-IPQ806x-PCIE-reset-changes.patch

Compile-tested on: ipq40xx, lantiq/xrx200, x86/64, ipq806x
Runtime-tested on: ipq40xx, lantiq/xrx200, x86/64

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2021-01-12 23:55:26 +01:00
Petr Štetiar
b14eeccdfe ath79: image: fix initramfs for safeloader devices
Currently it's not possible to tftpboot initramfs image on archer-c7-v5
as the image contains tplink-v1-header which leads to:

 ath> bootm
 ## Booting image at 81000000 ...
 Bad Magic Number

as U-Boot expects uImage wrapped image. This is caused by following
inheritance issue:

  define Device/Init
    KERNEL_INITRAMFS = $$(KERNEL)

  define Device/tplink-v1
    KERNEL := kernel-bin | append-dtb | lzma
    KERNEL_INITRAMFS := kernel-bin | append-dtb | lzma | tplink-v1-header

  define Device/tplink-safeloader
    $(Device/tplink-v1)

  define Device/tplink-safeloader-uimage
    $(Device/tplink-safeloader)
    KERNEL := kernel-bin | append-dtb | lzma | uImageArcher lzma

  define Device/tplink_archer-c7-v5
    $(Device/tplink-safeloader-uimage)

where tplink-v1 defines KERNEL_INITRAMFS with tplink-v1-header and it's
then used by all devices inheriting from tplink-safeloader. Fix this by
overriding KERNEL_INITRAMFS to KERNEL variable again.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit ceeece9ffa)
2020-12-17 15:51:43 +01:00
Hauke Mehrtens
cb58c7fe73 kernel: bump 4.14 to 4.14.212
Refreshed all patches.

Removed patches because included in upstream:
- 315-v5.10-usbnet-ipeth-fix-connectivity-with-ios-14.patch

Compile-tested on: ipq40xx, ath79, x86/64
Runtime-tested on: ipq40xx, ath79

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2020-12-16 22:23:52 +01:00
Petr Štetiar
193adc94d1 ar71xx,ath79: refresh 910-unaligned_access_hacks.patch
Commit c9c7b4b394 ("kernel: add netfilter-actual-sk patch") has
touched net/ipv6/netfilter/ip6table_mangle.c which in turn has affected
910-unaligned_access_hacks.patch so the patch needs to be refreshed.

Fixes: c9c7b4b394 ("kernel: add netfilter-actual-sk patch")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-11-24 09:27:50 +01:00
Koen Vandeputte
ac5297340e kernel: bump 4.14 to 4.14.206
Refreshed all patches.

Altered patches:
- 210-dwc2_defaults.patch
- 708-mc-bus-support-layerscape.patch

Fixes:
- CVE-2020-25656

Compile-tested on: ar71xx, cns3xxx, imx6, x86_64
Runtime-tested on: ar71xx, cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2020-11-16 09:35:05 +01:00
Roger Pueyo Centelles
589c3cf4e0 ath79: remove wmac mtd-mac-address for UniFi AC family
The MAC address for the wmac 2.4 GHz radio of the Ubiquiti UniFi AC
family of devices is actually embedded in the mtd-cal-data, so there
is no need for mtd-mac-address (which was incorrectly forcing wmac
to have the same MAC as eth0). This makes it coherent with the stock
firmware and the ar71xx target:

 · XX:XX:XX:X0:XX:XX eth0
 · XX:XX:XX:X1:XX:XX ath0/wlan1 (2.4 GHz)
 · XX:XX:XX:X2:XX:XX ath1/wlan0 (5 GHz)

Checked on a UniFi AC Mesh, a UniFi AC LR and a UniFi Lite.

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
(cherry picked from commit 20ace70db6)
2020-11-12 18:04:50 +01:00
David Bauer
ad3c2b9736 ath79: use correct firmware name for UniFi AP
The Ubiquiti UniFi AP does not have a AHB connected radio but a PCI one.
Also the EEPROM ist only 0x440 bytes of length.

Reported-by: Martin Weinelt <martin@darmstadt.freifunk.net>
Tested-by: Martin Weinelt <martin@darmstadt.freifunk.net>
Signed-off-by: David Bauer <mail@david-bauer.net>
(backported from commit 4c5eb1040f)
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-11-11 17:32:25 +01:00
Adrian Schmutzler
c25e3275ac ath79: fix LED labels for PowerCloud CAP324
The order of function and color in the labels in inverted for the
LAN LEDs. Fix it.

Fixes: 915966d861 ("ath79: Port PowerCloud Systems CAP324 support")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 96023cd4ba)
2020-11-11 17:26:52 +01:00
Koen Vandeputte
9c718b5478 kernel: bump 4.14 to 4.14.200
Refreshed all patches.

Compile-tested on: ar71xx, cns3xxx, imx6, x86_64
Runtime-tested on: ar71xx, cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2020-10-12 09:45:54 +02:00
Chuanhong Guo
b21bea7b1b ath79: ar8216: make switch register access atomic
reg accesses on integrated ar8229 sometimes fails. As a result, phy read
got incorrect port status and wan link goes down and up mysteriously.
After comparing ar8216 with the old driver, these local_irq_save/restore
calls are the only meaningful differences I could find and it does fix
the issue.
The same changes were added in svn r26856 by Gabor Juhos:
ar71xx: ag71xx: make switch register access atomic

As I can't find the underlying problem either, this hack is broght
back to fix the unstable link issue.
This hack is only suitable for ath79 mdio and may easily break the
driver on other platform. Limit it to ath79-only as a target patch.

Fixes: FS#2216
Fixes: FS#3226
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
(cherry picked from commit 86fdc8abed)
2020-10-11 11:57:55 +08:00
Adrian Schmutzler
f4286d7bc2 ath79: fix rssi-low LED for My Net Range Extender
The LED color was missing in 01_leds.

Fixes: 745dee11ac ("ath79: add support for WD My Net Wi-Fi Range
Extender")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit d232a8ac7d)
2020-09-28 13:33:28 +02:00
Hauke Mehrtens
d82e6a2f10 kernel: Update to version 4.14.199
Compile and runtime tested on lantiq/xrx200 + ath79/generic.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2020-09-28 01:04:35 +02:00
Adrian Schmutzler
8b0278a17e ath79: add support for TP-Link TL-WR710N v2.1
This adds support for the TP-Link TL-WR710N v2.1. It is basically a
re-issue of the v1.2.

Specifications:

SoC:       Atheros AR9331
CPU:       400 MHz
Flash:     8 MiB
RAM:       32 MiB
WiFi:      2.4 GHz b/g/n
Ethernet:  2x 100M ports
USB:       1x 2.0

The only difference from the v1 is the TP-Link hardware ID/revision.

Attention:
The TL-WR710N v2.0 (!) has only 4 MB flash and cannot be flashed with
this image. It has a different TPLINK_HWREV, so accidental flashing
of the factory image should be impossible without additional measures.

Unfortunately, the v2.0 in ar71xx has the same board name, so sysupgrade
from ar71xx v2.0 into ath79 v1/v2.1 will not be prevented, but will brick
the device.

Flashing instruction:

Upload the factory image via the OEM firmware GUI upgrade mechanism.

Further notes:

To make implementation easier if somebody desires to port the 4M v2.0,
this already creates two DTSI files.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Fabian Eppig <fabian@eppig.de>
(backported from eb531337a7)
2020-08-24 19:56:10 +02:00
Adrian Schmutzler
008db6b970 ath79: enable gpio on ar933x by default
All other SoC DTSI files have gpio enabled by default, only
ar9330/ar9331 disable it by default, only to have it enabled again
afterwards for each individual device.

So, do not disable it in the first place, and drop all device-specific
status statements afterwards.

Though this is a cosmetic commit, it might be a pitfall for
device-support backporters if missing. Since backporting it is trivial,
let's just do it.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit dc1280ef65)
2020-08-18 17:45:20 +02:00
Adrian Schmutzler
3df63fba70 ath79: fix syntax error in ar7240_tplink_tl-wa.dtsi
The node needs to be terminated by a semicolon.

Fixes: 8484a764df ("ath79: ar724x: make sure builtin-switch is
enabled in DT")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit e329e71c69)
2020-08-17 18:29:03 +02:00
Adrian Schmutzler
be09fdbf36 ath79: ar724x: make sure builtin-switch is enabled in DT
On ar7240/ar7241 the mdioX node with the builtin-switch is enabled
in the DTSI files, but the parent ethX node is left disabled. It
only gets enabled per device or device family, and has not been
enabled at all yet for the TP-Link WA devices with ar7240, making
the switch unavailable there.

This patch makes sure &eth0/&eth1 nodes are enabled together with
the &mdio0/&mdio1 nodes containing the builtin-switch.
For ar7240_tplink_tl-wa.dtsi, &eth0 is properly hidden again via
  compatible = "syscon", "simple-mfd";

This partially fixes FS#2887, however it seems dmesg still does
not show cable (dis)connect in dmesg for ar7240 TP-Link WA
devices.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 8484a764df)
2020-08-17 15:52:01 +02:00
Michal Cieslakiewicz
5d3e5d6ccc ath79: WNR612v2: improve device support
This patch improves ath79 support for Netgear WNR612v2.
Router functionality becomes identical to ar71xx version.

Changes include:
* software control over LAN LEDs via sysfs
* correct MAC addresses for network interfaces
* correct image size in device definition
* dts: 'keys' renamed to 'ath9k-keys'
* dts: 'label-mac-device' set to eth1 (LAN)
* dts: formatting adjustments

Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
(cherry picked from commit d74324e407)
[remove label-mac-device]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-17 15:49:57 +02:00
Michal Cieslakiewicz
fba9a88821 ath79: add LAN LEDs control bits for AR724x GPIO function pinmux
Currently AR724x pinmux for register 0x18040028 controls only JTAG disable bit.
This patch adds new DTS settings to control LAN LEDs and CLKs that allow
full software control over these diodes - exactly the same is done by ar71xx
target in device setup phase for many routers (WNR2000v3 for example).

'switch_led_disable_pins' clears AR724X_GPIO_FUNC_ETH_SWITCH_LED[0-4]_EN bits.
'clks_disable_pins' clears AR724X_GPIO_FUNC_CLK_OBS[1-5]_EN and
AR724X_GPIO_FUNC_GE0_MII_CLK_EN bits. These all should be used together, along
with 'jtag_disable_pins', to allow OS to control all GPIO-connected LEDs and
buttons on device.

Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
(cherry picked from commit 69df7eb73d)
2020-08-17 15:49:01 +02:00
Hauke Mehrtens
148d59c67e kernel: update kernel 4.14 to version 4.14.193
Compile and runtime tested on lantiq/xrx200 and ipq40xx.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2020-08-11 00:12:50 +02:00
Adrian Schmutzler
1b3aca9142 ath79: restore support for boot console with arbitrary baud rates
The Arduino Yun uses a baud rate of 250000 by default. The serial is
going over the Atmel ATmega and is used to connect to this chip.
Without this patch Linux wants to switch the console to 9600 Baud.

With this patch Linux will use the configured baud rate and not a
default one specified in uart_register_driver().

This has been added for ath79 4.19 and 5.4 in master as part of
fc59b2f79b ("ath79: add support for Arduino Yun"), this backports
it separately to 4.14.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-02 18:15:45 +02:00
Adrian Schmutzler
a2c9fc9ff0 ath79: correctly define WiFi switch for TL-WR841ND v8
The TL-WR841ND v8 feature a WiFi switch instead of a button.
This adds the corresponding input-type to prevent booting into
failsafe regularly.

This has been defined correctly in ar71xx, but was overlooked
when migrating to ath79. In contrast, the TL-WR842ND v2, which
has the key set up as switch in ar71xx, actually has a button.
The TL-MR3420 v2 has a button as well and is set up correctly
for both targets. (Information based on TP-Link user guide)

Note:

While looking into this, I found that support PR for TL-MR3420 v2
switched reset button to ACTIVE_HIGH. However, the other two
device still use ACTIVE_LOW. This seems strange, but I cannot
verify it lacking the affected devices.

Fixes: FS#2733
Fixes: 9601d94138 ("add support for TP-Link TL-WR841N/ND v8")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(backported from commit 5e86877f36)
2020-07-23 17:40:23 +02:00
Hauke Mehrtens
f4985a22ca kernel: Update kernel 4.14 to version 4.14.187
Fixes:
- CVE-2020-10757

Run tested: ath79, ipq40xx
Build tested: ath79, ipq40xx

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2020-07-04 19:22:23 +02:00
Adrian Schmutzler
8293c8ed46 ath79: do not build TP-Link tiny images by default
For quite some time, the tiny (4M flash) TP-Link sysupgrade and
factory images cannot be built anymore by the buildbots, just
the initramfs-kernel.bin files are still there.

Disable these images for the buildbots and don't waste build
resources.

Note that these devices still build fine with default settings,
just not with the additional packages and config symbols for
the buildbots.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-06-28 14:37:22 +02:00
Adrian Schmutzler
b40e6bc55f ath79: drop and consolidate redundant chosen/bootargs
In ath79, for several SoCs the console bootargs are defined to the
very same value in every device's DTS. Consolidate these definitions
in the SoC dtsi files and drop further redundant definitions elsewhere.

The only device without any bootargs set has been OpenMesh OM5P-AC V2.
This will now inherit the setting from qca955x.dtsi

While this is a cosmetic change, backporting it to 19.07 will be a
major help for anyone doing backports of device support. Without it,
every backporter would have to remember to manually add the chosen node
to the device's DTS.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 635f111148)
2020-06-28 14:24:59 +02:00
Adrian Schmutzler
153392e209 ath79: add support for TP-Link TL-WA801ND v3/v4
This ports support for these devices from ar71xx.

Specification:

- System-On-Chip: Qualcomm Atheros QCA9533
- CPU/Speed: v3: 560 MHz, v4: 650 MHz
- Flash: 4096 KiB
- RAM: 32 MiB
- Ethernet: 1 port @ 100M
- Wireless: SoC-integrated: QCA9533 2.4GHz 802.11bgn

In contrast to the implementation in ar71xx (reset and WiFi button),
the device actually features reset and WPS buttons.

Flashing instructions:

Upload the ...-factory.bin file via OEM web interface.

TFTP Recovery:

1. Set PC to fixed IP address 192.168.0.66
2. Download *-factory.bin image and rename it to
   wa801ndv3_tp_recovery.bin
3. Start a tftp server with the image file in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
   the firmware should be transferred from the tftp server
8. Wait ~30 second to complete recovery.

TFTP recovery has only been tested with v3, and the Wiki states
that the procedure won't work for v4, which cannot be verified
or falsified at the moment.

Tested by Tim Ward (see forum):
https://forum.openwrt.org/t/ath79-support-for-tp-link-tl-wa901nd-v3-v4-v5/61246/13

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 9a477b833a)
2020-06-21 21:34:09 +02:00
Christian Lamparter
f7f15f8033 ath79: wndr3700 series: fix wifi range & throughput
This patch adds ar71xx's GPIO setup for the 2.4GHz and 5GHz antennae
demultiplexer:

| 158         /* 2.4 GHz uses the first fixed antenna group (1, 0, 1, 0) */
| 159         ap9x_pci_setup_wmac_gpio(0, (0xf << 6), (0xa << 6));
| 160
| 161         /* 5 GHz uses the second fixed antenna group (0, 1, 1, 0) */
| 162         ap9x_pci_setup_wmac_gpio(1, (0xf << 6), (0x6 << 6));

This should restore the range and throughput of the 2.4GHz radio
on all the derived wndr3700 variants and versions with the AR7161 SoC.
A special case is the 5GHz radio. The original wndr3700(v1) will
benefit from this change. However the wndr3700v2 and later revisions
were unaffected by the missing bits, as there is no demultiplexer
present in the later designs.

This patch uses gpio-hogs within the device-tree for all
wndr3700/wndr3800/wndrmac variants.

Notes:

Based on the PCB pictures, the WNDR3700(v1) really had eight
independent antennae. Four antennae for each radio and all of
those were printed on the circut board.

The WNDR3700v2 and later have just six antennae. Four of those
are printed on the circuit board and serve the 2.4GHz radio.
Whereas the remaining two are special 5GHz Rayspan Patch Antennae
which are directly connected to the 5GHz radio.

Hannu Nyman dug pretty deep and unearthed a treasure of information
regarding the history of how these values came to be in the OpenWrt
archives: <https://dev.archive.openwrt.org/ticket/6533.html>.

Mark Mentovai came across the fixed antenna group when he was looking
into the driver:

    fixed_antenna_group 1, (0, 1, 0, 1)
    fixed_antenna_group 2, (0, 1, 1, 0)
    fixed_antenna_group 3, (1, 0, 0, 1)
    fixed_antenna_group 4, (1, 0, 1, 0)

Fixes: FS#3088

Reported-by: Luca Bensi
Reported-by: Maciej Mazur
Reported-by: Hannu Nyman <hannu.nyman@iki.fi>
Debugged-by: Hannu Nyman <hannu.nyman@iki.fi>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(cherry picked from commit 61307544d1)
2020-06-09 22:46:21 +02:00
Lech Perczak
e752fc1ff9 ath79: add support for TP-Link TL-WR802N V1 and V2
Specification:
- SoC: Qualcomm Atheros QCA9533 (560 MHz, MIPS 24Kc)
- RAM: 32 MiB
- Storage: 4 MiB of Flash on board
- Wireless: Built into QCA9533 (Honey Bee), PHY modes b/g/n
- Ethernet: 1x100M (port0)

Installation through OEM Web Interface:
- Connect to TL-WR802N by Ethernet or Wi-Fi
- Go to web interface:
  [V1] http://192.168.0.1
  [V2] http://192.168.0.254
  Default user is "admin" & password is "admin".
  On V2, there is no DHCP server running by default, so remember to set
  IP manually.
- Go to "System Tools -> Firmware Upgrade"
- Browse for firmware:
  [V1] "*.factory.bin"
  [V2] "*.factory-us.bin" or  "*.factory-eu.bin" for eu model
  Web interface may complain if filename is too long. In such case,
  rename .bin to something shorter.
- Click upgrade

Installation through tftp:
Note: T_OUT, T_IN and GND on the board must be connected to USB TTL
      Serial Configuration 115200 8n1

- Boot the TL-WR802N
- When "Autobooting in 1 seconds" appears type "tpl" followed by enter
- Connect to the board Ethernet port
    (IPADDR: 192.168.1.1, ServerIP: 192.168.1.10)
- tftpboot 0x80000000 <Firmware Image Name>
- Record the result of "printenv bootcmd"
- Enter "erase <Result of 'printenv bootcmd'> +0x3c0000"
    (e.g erase 0x9f020000 +0x3c0000)
- Enter "cp.b 0x80000000 <Result of 'printenv bootcmd'> 0x3c0000"
    (e.g cp.b 0x80000000 0x9f020000 0x3c0000)
- Enter "bootm <Result of 'printenv bootcmd'>"
    (e.g bootm 0x9f020000)

Notes:

When porting from ar71xx target to ath79, I found out that on V2,
reset button is on GPIO12 and active low, instead of GPIO11 and
active high. By cross-flashing V1 firmware to V2, I confirmed
the same is true for V1.
Also according to manual of V1, this one also has green
LED instead of blue - both of those issues were fixed accordingly.

The MAC address assignment has been checked with OEM firmware.

Installation manual based on ar71xx support by Thomas Roberts

Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
[slightly adjust commit message, add MAC address comment]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 7e513136c6)
2020-06-03 15:29:37 +02:00
Roger Pueyo Centelles
6488d2f7cc ath79: update WA/XC devices UBNT_VERSION to 8.5.3
Ubiquiti WA devices with newer hw version 2011K require UBNT_VERSION
to be at least 8.5.3, otherwise the image is rejected:

   New ver: WA.ar934x.v8.5.0-42.OpenWrt-r10947-65030d81f3
   Versions: New(525568) 8.5.0, Required(525571) 8.5.3
   Invalid version 'WA.ar934x.v8.5.0-42.OpenWrt-r10947-65030d81f3'

For consistency, also increase version number for XC devices.

Tested-by: Pedro <pedrowrt@cas.cat>
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
(cherry picked from commit 95caa3436d)
2020-06-03 15:29:20 +02:00
Adrian Schmutzler
e36bdd5dc5 ath79: fix LEDs for GL.inet GL-AR150
Since the wireless LED was used for boot and set up with a DT
trigger, the WiFi indication hasn't worked on ath79 at all.

In addition, a look into the manual revealed that the OEM
configuration is as follows:

LED 1 (green): power
LED 2 (green): configurable
LED 3 (red): wireless

So, let's just keep the WiFi trigger and convert the rest to its
"intended" use.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 705fe43522)
2020-06-03 15:28:50 +02:00
Adrian Schmutzler
6a89098935 ath79: add support for TP-Link TL-WA901ND v4 and v5
This ports support for the TL-WA901ND v4 and v5 from ar71xx to ath79.
They are similar to the TP9343-based TL-WR940N v3/v4 and TL-WR941ND v6.

Specifications:
  SoC: TP9343
  Flash/RAM: 4/32 MiB
  CPU: 750 MHz
  WiFi: 2.4 GHz b/g/n
  Ethernet: 1 port (100M)

Flashing instructions:
  Upload the factory image via the vendor firmware upgrade option.

Flash instruction (TFTP):
  1. Set PC to fixed ip address 192.168.0.66
  2. Download *-factory.bin image and rename it to * (see below)
  3. Start a tftp server with the image file in its root directory
  4. Turn off the router
  5. Press and hold Reset button
  6. Turn on router with the reset button pressed and wait ~15 seconds
  7. Release the reset button and after a short time
     the firmware should be transferred from the tftp server
  8. Wait ~30 second to complete recovery.

  * The image name for TFTP recovery is wa901ndv4_tp_recovery.bin for
  both variants.

In ar71xx, a MAC address with offset 1 was used for ethernet port.
That's probably wrong, but this commit sticks to it until we know
the correct value.

Like in ar71xx, this builds the default factory.bin with EU country
code.

Thanks to Leonardo Weiss for testing on the v5.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(backported from commit 4a61a88f90)
2020-05-20 21:06:48 +02:00
Adrian Schmutzler
a6f70f2e97 ath79: add support for TP-Link TL-WA701ND/730RE/801ND/901ND v1
This adds support for the various clones of the TL-WA830RE recently
supported in fb99ac6807 ("ath79: add support for TP-Link TL-WA830RE v1"):

- tplink,tl-wa701nd-v1
- tplink,tl-wa730re-v1
- tplink,tl-wa801nd-v1
- tplink,tl-wa830re-v1 (already supported)
- tplink,tl-wa901nd-v1

Since these devices are 100%-clones in ar71xx, this patch adds all
of them without run-testing (as this has been done for TL-WA830RE v1).

Specifications:
- SOC: Atheros AR7240
- CPU: 400MHz
- Flash: 4 MiB (Spansion S25FL032P)
- RAM: 32 MiB (Zentel A3S56D40FTP-G5)
- WLAN: Atheros AR9280 bgn 2x2
- Ethernet: 1 port (100M)

Flash instructions:
- install from u-boot with tftp (requires serial access)
  > setenv ipaddr a.b.c.d
  > setenv serverip e.f.g.h
  > tftpboot 0x80000000 \
      openwrt-ath79-tiny-tplink_tl-waxxxxx-v1-squashfs-factory.bin
  > erase 0x9f020000 +0x3c0000
  > cp.b 0x80000000 0x9f020000 0x3c0000
  > bootm 0x9f020000
- flash factory image from OEM WebUI
- sysupgrade from ar71xx image

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(backported from commit 2f1cc5c3d5)
2020-05-20 20:51:28 +02:00
Adrian Schmutzler
8c6c488e9e ath79: add support for TP-Link TL-WR940N v6
The TL-WR940N v6 is similar to v3/v4, it just has different
LEDs and MAC address assignment.

Specification:
- 750 MHz CPU
- 32 MB of RAM
- 4 MB of FLASH
- 2.4 GHz WiFi
- 4x 10/100 Mbps Ethernet

The use of LEDs is based on ar71xx, so blue LED is used for WAN
and orange LED for diag (boot/failsafe/etc.).

Flash instruction (WebUI):
Download *-factory.bin image and upload it via the firmwary upgrade
function of the stock firmware WebUI.

Flash instruction (TFTP):
1. Set PC to fixed ip address 192.168.0.66
2. Download *-factory.bin image and rename it to
   wr940nv6_tp_recovery.bin
3. Start a tftp server with the image file in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
the firmware should be transferred from the tftp server
8. Wait ~30 second to complete recovery.

Thanks to Manuel Kock for reviewing and testing this patch.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Manuel Kock <github.web@manu.li>
(backported from commit fbd00bb8d4)
2020-05-20 20:47:05 +02:00
Christian Buschau
36d4140517 ath79: add support for TP-Link TL-WA830RE v1
This ports support for the TL-WA830RE v1 range extender from ar71xx to
ath79.

Specifications:
- SOC: Atheros AR7240
- CPU: 400MHz
- Flash: 4 MiB (Spansion S25FL032P)
- RAM: 32 MiB (Zentel A3S56D40FTP-G5)
- WLAN: Atheros AR9280 bgn 2x2
- Ethernet: 1 port (100M)

Flash instructions:
- install from u-boot with tftp (requires serial access)
  > setenv ipaddr a.b.c.d
  > setenv serverip e.f.g.h
  > tftpboot 0x80000000 \
      openwrt-ath79-tiny-tplink_tl-wa830re-v1-squashfs-factory.bin
  > erase 0x9f020000 +0x3c0000
  > cp.b 0x80000000 0x9f020000 0x3c0000
  > bootm 0x9f020000
- flash factory image from OEM WebUI
- sysupgrade from ar71xx image

The device seems to be a clone of the following devices not yet
added to ath79:
- tl-wa701nd-v1
- tl-wa730re-v1
- tl-wa801nd-v1
- tl-wa901nd-v1

Signed-off-by: Christian Buschau <christian.buschau@mailbox.org>
[make use of ar7240_tplink.dtsi, add note about clones]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit fb99ac6807)
2020-05-20 20:47:05 +02:00
Adrian Schmutzler
7187826b8b ath79: reorganize DTSI for ar7240 TP-Link devices
The current set of TP-Link devices with ar7240 SoC all share
the same DTSI file. As the latter is very similar to the
definition required for the to-be-supported TP-Link TL-WA devices
with ar7240, this patch splits the definitions into a shared part
for all TP-Link devices (ar7240_tplink.dtsi) and a file containing
the specific setup for the present TL-WR devices
(ar7240_tplink_tl-wr.dtsi), equivalent to the former
ar7240_tplink_tl-wr74xn-v1.dtsi.

While at it, remove unused firmware partition label and rename
pinmux_switch_led_pins.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 273e00c4a5)
2020-05-20 20:47:05 +02:00
Lim Guo Wei
d4092eac1f ath79: migrate TP-Link TL-MR3420v2 to ath79
Specifications:
- SoC: ar9341
- RAM: 32M
- Flash: 4M
- Ethernet: 5x FE ports
- WiFi: ar9341-wmac

Flash instruction:
Upload generated factory firmware on vendor's web interface.

This changes the key assignment compared to ar71xx support of this
device, since of the two keys on the device one is used as combined
Reset/WPS and the second one as WiFi on/off button.
Despite, the reset button required GPIO_ACTIVE_HIGH to work correctly.

Signed-off-by: Lim Guo Wei <limguowei@gmail.com>
[redo commit message]
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
(backported from commit e7ab1b5173)
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-20 20:47:01 +02:00
Adrian Schmutzler
24cfd961d9 ath79: add support for TP9343-based TP-Link TL-WR94x devices
This adds support for several TP-Link devices based on TP9343
("a QCA9561 without PCIe and USB"):
- TL-WR940N v3
- TL-WR940N v4
- TL-WR941ND v6

The devices are only different concerning LEDs and MAC address
assignment.

All TL-WR940 are with non-detachable antennas (N), all
TL-WR941 devices are with detachable antennas (ND).

Specification:
- 750 MHz CPU
- 32 MB of RAM
- 4 MB of FLASH
- 2.4 GHz WiFi
- 4x 10/100 Mbps Ethernet

Flash instruction (WebUI):
Download *-factory.bin image and upload it via the firmwary upgrade
function of the stock firmware WebUI.

Flash instruction (TFTP):
1. Set PC to fixed ip address 192.168.0.66
2. Download *-factory.bin image and rename it to * (see below)
3. Start a tftp server with the image file in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
the firmware should be transferred from the tftp server
8. Wait ~30 second to complete recovery.

* TFTP image names:
940 v3: wr941ndv6_tp_recovery.bin
940 v4: wr940nv4_tp_recovery.bin
941 v6: wr941ndv6_tp_recovery.bin

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(backported picked from commit c02b9818a5)
2020-05-20 20:11:33 +02:00
Lech Perczak
ecea10f2b9 ath79: dts: add missing 'serial0' alias for TP-Link TL-MR3040v2
Out of all devices currently supported based on AR9331 chipset,
this one had the 'serial0' alias missing. Add it to fix setting of
/dev/console and login shell on the onboard UART.

Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
(cherry picked from commit 94f3449977)
2020-05-11 11:17:59 +02:00
Adrian Schmutzler
f40947a8c0 ath79: indicate boot/failsafe/upgrade for NanoBeam/Nanostation AC
Like for Ubiquiti PowerBeam 5AC Gen2, the highest RSSI LED can
be exploited to indicate boot/failsafe/upgrade for the NanoBeam AC
and Nanostation AC as well.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 80a094aaf3)
2020-05-04 21:31:04 +02:00
Adrian Schmutzler
65cf72d5d2 ath79: add SUPPORTED_DEVICES based on ar71xx for some devices
This adds some still-missing board names for old TP-Link devices
to ath79 SUPPORTED_DEVICES.

Fixes: FS#3017

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 522f6b7eee)
2020-05-04 21:25:38 +02:00
Petr Štetiar
f9ef0c5705 kernel: bump 4.14 to 4.14.178
Refreshed all patches and removed upstreamed:

 oxnas/001-irqchip-versatile-fpga-Handle-chained-IRQs-properly.patch
 oxnas/002-irqchip-versatile-fpga-Apply-clear-mask-earlier.patch

Fixes: CVE-2020-12114 and CVE-2020-11669

Runtime-tested on: qemu-x86-64
Compile-tested on: ath79/generic, x86/64, imx6

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-05-04 21:05:21 +02:00
Koen Vandeputte
0232f57e1a kernel: bump 4.14 to 4.14.176
Refreshed all patches.

Remove upstreamed:
- 0001-net-thunderx-workaround-BGX-TX-Underflow-issue.patch
- 600-ipv6-addrconf-call-ipv6_mc_up-for-non-Ethernet-inter.patch
- 003-ARM-dts-oxnas-Fix-clear-mask-property.patch

Fixes:
- CVE-2020-8647
- CVE-2020-8648 (potentially)
- CVE-2020-8649

Compile-tested on: cns3xxx, octeontx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2020-04-16 13:23:52 +02:00
Adrian Schmutzler
286c407c3d ath79: add SUPPORTED_DEVICES for TP-Link TL-WA901ND v2
This adds the board name from ar71xx to support upgrade without
-F for the TP-Link TL-WA901ND v2.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 508462a399)
2020-04-15 13:02:05 +02:00
Adrian Schmutzler
470f7c046c ath79: add support for TP-Link TL-WDR4310 v1
This device seems to be identical to the TL-WDR4300, just with
different release date/region and TPLINK_HWID.

Support is added based on the ar71xx implementation.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 676ca94c3c)
2020-03-30 19:36:15 +02:00
Adrian Schmutzler
bdbda30384 ath79: add support for TP-Link TL-WA860RE v1
This ports support for the TL-WA860RE v1 range extender from ar71xx
to ath79.

Specifications:
  Board: AP123 / AR9341 rev. 3
  Flash/RAM: 4/32 MiB
  CPU: 535 MHz
  WiFi: 2.4 GHz b/g/n
  Ethernet: 1 port (100M)
  Two external antennas

Flashing instructions:
  Upload the factory image via the vendor firmware upgrade option.

Recovery:
  Note that this device does not provide TFTP via ethernet like many
  other TP-Link devices do. You will have to open the case if you
  require recovery beyond failsafe.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Sebastian Knapp <sebastian4842@outlook.com>
(cherry picked from commit 385f4868bc)
2020-03-27 17:15:07 +01:00
Adrian Schmutzler
2e6bfab8c5 ath79: add support for TP-Link TL-WA850RE v1
This ports support for the TL-WA850RE v1 range extender from ar71xx
to ath79.

Specifications:
  Board: AP123 / AR9341 rev. 3
  Flash/RAM: 4/32 MiB
  CPU: 535 MHz
  WiFi: 2.4 GHz b/g/n
  Ethernet: 1 port (100M)

Flashing instructions:
Upload the factory image via the vendor firmware upgrade option.

Recovery:
Note that this device does not provide TFTP via ethernet like many
other TP-Link devices do. You will have to open the case if you
require recovery beyond failsafe.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 6eaea3a8ba)
2020-03-27 17:14:58 +01:00
Adrian Schmutzler
456e1c60d6 ath79: add support for TP-Link WDR3500 v1
Hardware:
SoC:      AR9344
CPU:      560 MHz
Flash:    8 MiB
RAM:      128 MiB
WiFi:     Atheros AR9340 2.4GHz 802.11bgn
          Atheros AR9300 5GHz 802.11an
Ethernet: AR934X built-in switch, WAN on separate physical interface
USB:      1x 2.0

Flash instruction (WebUI):
Download *-factory.bin image and upload it via the firmwary upgrade
function of the stock firmware WebUI.

Flash instruction (TFTP):
1. Set PC to fixed ip address 192.168.0.66
2. Download *-factory.bin image and rename it to
   wdr3500v1_tp_recovery.bin
3. Start a tftp server with the image file in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
the firmware should be transferred from the tftp server
8. Wait ~30 second to complete recovery.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
[removed stray newline]
Signed-off-by: David Bauer <mail@david-bauer.net>
(backported from commit fbbb4eb8b4)
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-03-20 12:22:18 +01:00
Adrian Schmutzler
e7fae8fc97 ath79: add support for TP-Link Archer C60 v3
TP-Link Archer C60 v3 is a dual-band AC1350 router,
based on Qualcomm/Atheros QCA9561 + QCA9886.

It seems to be identical to the v2 revision, except that
it lacks a WPS LED and has different GPIO for amber WAN LED.

Specification:

- 775/650/258 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 2T2R 5 GHz
- 5x 10/100 Mbps Ethernet
- 6x LED, 2x button
- UART header on PCB

Flash instruction (WebUI):
Download *-factory.bin image and upload it via the firmwary upgrade
function of the stock firmware WebUI.

Flash instruction (TFTP):
1. Set PC to fixed IP address 192.168.0.66
2. Download *-factory.bin image and rename it to tp_recovery.bin
3. Start a tftp server with the file tp_recovery.bin in its root
   directory
4. Turn off the router
5. Press and hold reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time the firmware should
   be transferred from the tftp server
8. Wait ~30 second to complete recovery

While TFTP works for OpenWrt images, my device didn't accept the
only available official firmware "Archer C60(EU)_V3.0_190115.bin".

In contrast to earlier revisions (v2), the v3 contains the (same)
MAC address twice, once in 0x1fa08 and again in 0x1fb08.
While the partition-table on the device refers to the latter, the
firmware image contains a different partition-table for that region:

name           device            firmware
factory-boot   0x00000-0x1fb00   0x00000-0x1fa00
default-mac    0x1fb00-0x1fd00   0x1fa00-0x1fc00
pin            0x1fd00-0x1fe00   0x1fc00-0x1fd00
product-info   0x1fe00-0x1ff00   0x1fd00-0x1ff00
device-id      0x1ff00-0x20000   0x1ff00-0x20000

While the MAC address is present twice, other data like the PIN isn't,
so with the partitioning from the firmware image the PIN on the device
would actually be outside of its partition.
Consequently, the patch uses the MAC location from the device (which
is the same as for the v2).

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 646d95c374)
2020-03-20 12:22:18 +01:00
Jun Su
7ae345ecb7 ath79: add support for TP-Link TL-WR740N v5
This adds support for the TP-Link TL-WR740N v5, a clone of the
v4 only with a different TPLINK_HWID. It was already supported
in ar71xx as well.

Specifications:

SOC: Atheros AR9331
CPU: 400MHz
Flash: 4 MiB
RAM: 32 MiB
WLAN: Atheros AR9330 bgn
Ethernet: 5 ports (100M)

Flashing instructions:

- Flash factory image from OEM WebUI:
  openwrt-ath79-tiny-tplink_tl-wr740n-v5-squashfs-factory.bin
- Sysupgrade from ar71xx image:
  openwrt-ath79-tiny-tplink_tl-wr740n-v5-squashfs-sysupgrade.bin

Signed-off-by: Jun Su <howard0su@gmail.com>
[commit title/message facelift, backport for 19.07]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit b9f4f1f97a)
2020-03-14 13:27:41 +01:00
Adrian Schmutzler
f1a3a6b79c ath79: fix port order on TP-Link Archer C60 v1/v2
The labels on the LAN ports of the TP-Link Archer C60 v1/v2 are
actually inverted compared to the ports of the internal switch.

Add this information to 02_network.

This is the same for to-be-supported v3 of this device.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit b054729899)
2020-03-14 13:20:29 +01:00