Referencing commit a1837135e0
Hardware
--------
SoC: Qualcomm Atheros QCA9558
RAM: 128M DDR2 (Nanya NT5TU64M16HG-AC)
FLASH: 128M SPI-NAND (Spansion S34ML01G100TFI00)
WLAN: QCA9558 3T3R 802.11 bgn
ETH: Qualcomm Atheros QCA8337
UART: 115200 8n1
BUTTON: Reset - WPS - "Router" switch
LED: 2x system-LED, 2x wlan-LED, 1x internet-LED,
2x routing-LED
LEDs besides the ethernet ports are controlled
by the ethernet switch
MAC Address:
use address(sample 1) source
label cc:e1:d5:xx:xx:ed art@macaddr_wan
lan cc:e1:d5:xx:xx:ec art@macaddr_lan
wan cc:e1:d5:xx:xx:ed $label
WiFi4_2G cc:e1:d5:xx:xx:ec art@cal_ath9k
Installation from Serial Console
------------
1. Connect to the serial console. Power up the device and interrupt
autoboot when prompted
2. Connect a TFTP server reachable at 192.168.11.10/24
to the ethernet port. Serve the OpenWrt initramfs image as
"openwrt.bin"
3. Boot the initramfs image using U-Boot
ath> tftpboot 0x84000000 openwrt.bin
ath> bootm 0x84000000
4. Copy the OpenWrt sysupgrade image to the device using scp and
install it like a normal upgrade (with no need to keeping config
since no config from "previous OpenWRT installation" could be kept
at all)
# sysupgrade -n /path/to/openwrt/sysupgrade.bin
Installation from Web Interface
------------
To flash just do a firmware upgrade from the stock firmware (Buffalo
branded dd-wrt) with squashfs-factory.bin
Signed-off-by: Edward Chow <equu@openmail.cc>
Link: https://github.com/openwrt/openwrt/pull/17227
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This reverts commit 3bd2cee9bf.
Based on my testing, we are unable to control USB power supply
through some third-party tools (e.g. uhubctl) or sysfs in userspace.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/17339
Signed-off-by: Robert Marko <robimarko@gmail.com>
set macaddress correctly for board
Signed-off-by: Florian Maurer <f.maurer@outlook.de>
Link: https://github.com/openwrt/openwrt/pull/17305
Signed-off-by: Robert Marko <robimarko@gmail.com>
The blocksize was too high, resulting in forgetting the config on sysupgrade
It is not needed for SPI-NOR.
Signed-off-by: Florian Maurer <f.maurer@outlook.de>
Link: https://github.com/openwrt/openwrt/pull/17305
Signed-off-by: Robert Marko <robimarko@gmail.com>
Tenbay WR3000K is an 802.11ax (Wi-Fi 6) router, based on MediaTek MT7981B.
- SoC: MetiaTek MT7981B
- RAM: Hynex H5TQ2G863GFR 512MiB
- Flash: Winbond W25N01GVZEIG 128MiB
- Wi-Fi: MediaTek MT7976C (2.4GHz/5GHz, 802.11ax, 2x2 MIMO, AX3000)
- MediaTek MT7915E: 2.4GHz and 5GHz
- Ethernet: 1x 10/100/1000 Mbps WAN + 3x 10/100/1000 Mbps LAN
- Switch: MediaTek MT7531AE
- UART: J4 (115200 baud)
- LEDs: Power
- Buttons: Reset, WPS
- PWR: 12V/1A DC, 5.5×2.1 connector
| Vendor | OpenWrt Interface | Address | Notes |
|---------|-------------------|---------------|------------------------------------------------|
| WAN | wan | Label MAC | Stored MAC in factory + offset 4, label MAC is Stored MAC - 2 |
| LAN | br-lan | Label MAC+1 | |
| 2.4GHz | phy0-ap0 | Label MAC + 2 | |
| 5GHz | phy1-ap0 | Label MAC + 3 | |
- 0x000000000000-0x000000100000 : "BL2"
- 0x000000100000-0x000000180000 : "u-boot-env"
- 0x000000180000-0x000000380000 : "Factory"
- 0x000000380000-0x000000580000 : "FIP"
- 0x000000580000-0x000003580000 : "ubi"
- 0x000003580000-0x000006580000 : "ubi1"
- 0x000006580000-0x0000065a0000 : "Product"
- 0x0000065a0000-0x000007580000 : "Custom"
- The original partition-Ubi partition-Ubi1 is an AB dual system, and Openwrt only uses Ubi. So flash requires modifying the uboot variable `boot_from=ubi` to ensure that it only starts from Ubi.
- The Product and Custom partitions are original and only exist to align with the original layout; they are not used by OpenWrt.
- id: 0, kernel
- id: 1, rootfs
- id: 2, rootfs_data
- **USB-to-TTL Serial Adapter** (e.g., CH340 or CP2102).
- **Dupont Wires** (male-to-male, 3 wires).
- **PC/Laptop** with a serial communication tool.
- Screwdriver (to open the router case).
1. **OpenWrt Firmware**:
- Download the appropriate `wr3000k-<build_time>-mediatek-filogic-tenbay_wr3000k-squashfs-sysupgrade.bin` firmware file for your router from the [OpenWrt website](https://openwrt.org/).
2. **Serial Communication Tool**:
- Windows: PuTTY, Tera Term.
- Linux/Mac: Minicom, screen.
3. (Optional) **TFTP Server**:
- Install a TFTP server like Tftpd64 or tftp-hpa.
---
1. Open the router casing and locate the **TX, RX, and GND** pins.
2. Connect the router pins to the USB-to-TTL adapter as follows:
- **TX (router)** → **RX (adapter)**
- **RX (router)** → **TX (adapter)**
- **GND (router)** → **GND (adapter)**
3. Do **not** connect the VCC pin to avoid damage.
- **Baud rate**: 115200
- **Data bits**: 8
- **Stop bits**: 1
- **Parity**: None
- **Flow control**: None
---
1. Power on the router and observe the serial terminal output.
2. When prompted (e.g., `Hit any key to stop autoboot: 3`), press the '/' key quickly to interrupt the boot process.
3. You will see the U-Boot Boot Menu:
```plaintext
*** U-Boot Boot Menu ***
1. Factory mode
2. Startup system (Default)
3. Upgrade firmware
4. Upgrade ATF BL2
5. Upgrade ATF FIP
6. Upgrade single image
7. Load image
0. U-Boot console
Press UP/DOWN to move, ENTER to select, ESC/CTRL+C to quit
```
4. Select Option 0 by typing 0 and pressing Enter.
5. Input into
```plaintext
MT7981> setenv boot_from ubi
MT7981> saveenv
Saving Environment to MTD... Erasing on MTD device 'nmbm0'... OK
Writing to MTD device 'nmbm0'... OK
OK
MT7981> printenv
baudrate=115200
boot_from=ubi
...
```
the above indicates system will start from *ubi*.
and then type
```plaintext
MT7981> reset
```
will boot from *ubi*
1. Power on the router and observe the serial terminal output.
2. When prompted (e.g., `Hit any key to stop autoboot: 3`), press the '/' key quickly to interrupt the boot process.
3. You will see the U-Boot Boot Menu:
```plaintext
*** U-Boot Boot Menu ***
1. Factory mode
2. Startup system (Default)
3. Upgrade firmware
4. Upgrade ATF BL2
5. Upgrade ATF FIP
6. Upgrade single image
7. Load image
0. U-Boot console
Press UP/DOWN to move, ENTER to select, ESC/CTRL+C to quit
```
4. Choose Option 3: Upgrade Firmware
Enter Upgrade Mode
Select Option 3 by typing 3 and pressing Enter.
Upgrade Methods
You will be prompted to choose between:
```plaintext
*** Upgrading Firmware ***
Run image after upgrading? (Y/n): y
Available load methods:
0 - TFTP client (Default)
1 - Xmodem
2 - Ymodem
3 - Kermit
4 - S-Record
5 - RAM
Select (enter for default): 0
Input U-Boot's IP address: 192.168.1.1
Input TFTP server's IP address: 192.168.1.10
Input IP netmask: 255.255.255.0
Input file name: wr3000k-<build_time>-mediatek-filogic-tenbay_wr3000k-squashfs-sysupgrade.bin
```
Type Enter to proceed. The router will erase the old firmware and write the new one.
Signed-off-by: Jianyu Zhuang <xzjianyu@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17172
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hardware:
SoC: MT7981b
RAM: 512 MB
Flash: 256 MB SPI NAND
Ethernet:
1x2.5Gbps (rtl8221b)
WiFi: 2x2 MT7981
Button: Reset
LED: 1x multicolor
Installation
------------
At the moment, firmware installation is only possible via a transition firmware.
It's can be requested from the manufacturer by email to support@cudy.com
Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17225
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The board has been redesigned due to previous hardware bugs
(with other reasons maybe).
Changes in new board:
- Added a gpio beeper
- Added a Atmel i2c eeprom
- Added a Atmel i2c ECC accelerator
- Added a Philips RTC module
- Added two RS485
- Removed WPS button
- Replaced USB3 port with M.2 B-key for LTE modules
- Swapped GbE LEDs gpio
Also assigned wifi mac with nvmem binding, added iface setup for failsafe,
increased phy assert time for rtl8221b, and updated LED labels.
Keeping compatibility for old version is not necessary here as only
few samples were sent to those interested in it.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/17253
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Specifications:
* SoC: Qualcomm IPQ8072A (64-bit Quad-core Arm Cortex-A53 @ 1.4 GHz)
* Memory: 2x ESMT M15T4G16256A-DEBG2G (1 GiB DDR3-1866 13-13-13)
* Serial Port: 3v3 TTL 115200n8
* Wi-Fi: QCA5054 (4x4 5 GHz 802.11ax)
* Wi-Fi: QCN5024 (2x2 2.4 GHz 802.11b/g/n/ax)
* Ethernet: AR8031 (10/100/1000BASE-T)
* Flash: Winbond W29N01HZSINF (128 MiB)
* LEDs: 1x Blue Status (GPIO 42 Active High)
* Buttons: 1x Reset (GPIO 50 Active Low)
Installation Instructions (Serial+TFTP):
1. Solder 4 pin header to JP1 and bridge pads of R58 and R62.
2. Connect 3V3 TTL port to TX, RX, and GND, which are positions 1, 2, and 3 respectively.
Be sure to crossover TX and RX.
3. Copy RAM firmware
openwrt-qualcommax-ipq807x-tplink_eap620hd-v1-initramfs-uImage.itb
to a TFTP server's root that is in the same subnet as your AP.
4. Power up the AP hold Ctrl+B in the serial console (115200n8) until autoboot is halted.
5. Run the following commands in the U-boot prompt:
# setenv serverip <TFTP server addr>
# setenv ipaddr <addr of AP>
# tftpboot 0x44000000 openwrt-qualcommax-ipq807x-tplink_eap620hd-v1-initramfs-uImage.itb
# bootm
You may need to type Ctrl+C and Enter before running these commands
to clear invisible characters from the buffer.
6. Run the following command in a terminal to copy the sysupgrade image
to be installed (check IP address):
$ scp -O openwrt-qualcommax-ipq807x-tplink_eap620hd-v1-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/
7. Activate the OpenWrt serial console and run the following commands:
# cd /tmp
# sysupgrade -n openwrt-qualcommax-ipq807x-tplink_eap620hd-v1-squashfs-sysupgrade.bin
8. The AP will reboot and OpenWrt will be successfully installed.
Known Issues:
* 5GHz radio instability (upstream current ath11k build bug maybe?)
Device support directly followed from EAP660HDv1 support
Links: #15832
Signed-off-by: Shymon Samsel <ssamsel@umass.edu>
Link: https://github.com/openwrt/openwrt/pull/17254
Signed-off-by: Robert Marko <robimarko@gmail.com>
In the process of upstreaming the local phy driver back in 2017, it
seems rt3050.dtsi was left out when updating the compatible string.
Add device reset as the driver needs it.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17257
Signed-off-by: Robert Marko <robimarko@gmail.com>
The dual-boot partition layout for the Zyxel GS1900 switches results in
6.9MB for both kernel and rootfs. Depending on the package selection,
this may already leave no space for the user overlay.
Merge the two firmware partitions, effectively dropping dual boot
support with OpenWrt. This results in a firmware partition of 13.9MB,
which should leave some room for the future.
To maintain install capabilites on new devices, an image is required
that still fits inside the original partition. The initramfs is used as
factory install image, so ensure this meets the old size constraints.
The factory image can be flashed via the same procedure as vendor images
when reverting to stock, can be installed from stock, or can be launched
via tftpboot.
Link: https://github.com/openwrt/openwrt/issues/16439
Link: https://github.com/openwrt/openwrt/pull/16442
Tested-by: Stijn Segers <foss@volatilesystems.org>
Signed-off-by: Sander Vanheule <sander@svanheule.net>
GPIO 5 on the RTL8231 is defined reset the system, but fails to actually
do so. This triggers a kernel a number of warnings and backtrace for
GPIO pins that can sleep, such as the RTL8231's. Two warnings are
emitted by libgpiod, and a third warning by gpio-restart itself after it
fails to restart the system:
[ 106.654008] ------------[ cut here ]------------
[ 106.659240] WARNING: CPU: 0 PID: 4279 at drivers/gpio/gpiolib.c:3098 gpiod_set_value+0x7c/0x108
[ Stack dump and call trace ]
[ 106.826218] ---[ end trace d1de50b401f5a153 ]---
[ 106.962992] ------------[ cut here ]------------
[ 106.968208] WARNING: CPU: 0 PID: 4279 at drivers/gpio/gpiolib.c:3098 gpiod_set_value+0x7c/0x108
[ Stack dump and call trace ]
[ 107.136718] ---[ end trace d1de50b401f5a154 ]---
[ 111.087092] ------------[ cut here ]------------
[ 111.092271] WARNING: CPU: 0 PID: 4279 at drivers/power/reset/gpio-restart.c:46 gpio_restart_notify+0xc0/0xdc
[ Stack dump and call trace ]
[ 111.256629] ---[ end trace d1de50b401f5a155 ]---
By removing gpio-restart from this device, we skip the restart-by-GPIO
attempt and rely only on the watchdog for restarts, which is already the
de facto behaviour.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Userspace handling is deprecated.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17311
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add the label-mac-device alias.
Signed-off-by: Fabian Bläse <fabian@blaese.de>
Link: https://github.com/openwrt/openwrt/pull/17313
Signed-off-by: Robert Marko <robimarko@gmail.com>
The AR8035 PHY is used in most Octeon boards supported by OpenWRT (all
the Ubiquiti routers at least). To be able to use its PHY-specific
functionality (cable testing, LED Control, ...) it should be built on
Octeon. It also needs the regulator framework, so enable that as well.
These boards are not space-constrained, so this really has no downsides.
Tested on an EdgeRouter Lite, cable tests now work with ethtool-full.
Signed-off-by: Lorenz Brun <lorenz@brun.one>
Link: https://github.com/openwrt/openwrt/pull/17318
Signed-off-by: Robert Marko <robimarko@gmail.com>
This backport patch inserted suspend/resume callbacks
for the wrong PHY driver.
The fixed patch is needed for Huawei AP5030DN
to initialize its second PHY.
Refresh all affected patch with make target/linux/refresh.
Fixes: 06cdc07f8c ("ath79: add support for Huawei AP5030DN")
Signed-off-by: Marco von Rosenberg <marcovr@selfnet.de>
Link: https://github.com/openwrt/openwrt/pull/17312
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Sets openwrt,netdev-name for the gmac nodes in the dts of BPI-R4 which
correspond to the two sfp slots. By default they are automatically
named as eth1 and eth2 in bad order, however 'SFP1-WAN' and 'SFP2-LAN'
are printed on the PCB and the official metal case has labels 'SFP-WAN'
and 'SFP-LAN'. Thus, label the ports accordingly to match the
board/case labels.
The COMPAT_VERSION is increased to denote that configuration has to be
adjusted manually.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Sets openwrt,netdev-name for the gmac1 node in the dts of BPI-R3, which
corresponds to the sfp1 slot, to have a proper naming and match the
label on the official BPI-R3 metal case. This renames the port from eth1
to sfp1.
The COMPAT_VERSION is increased to denote that configuration has to be
adjusted manually.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Add support in filogic subtarget for our own custom property
`openwrt,netdev-name` in the device tree instead of `label` for
renaming interfaces. This was suggested upstream to avoid potential
conflicts [1].
[1] https://lore.kernel.org/netdev/20240709124503.pubki5nwjfbedhhy@skbuf/
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Userspace handling is deprecated. MAC address stuff needs to remain
handled in userspace as it's encrypted. Maybe an NVMEM driver can be
written in the future...
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17276
Signed-off-by: Robert Marko <robimarko@gmail.com>
The qusb_phy node looks for the following supply:
"vdd", "vdda-pll", "vdda-phy-dpdm"
And ssphy node looks for the following supply:
"vdda-phy", "vdda-pll"
So fix the usb regulator supply for RT-AX89X.
Fixes: 1306237 ("qualcommax: use PHY regulator for USB GPIO")
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/17290
Signed-off-by: Robert Marko <robimarko@gmail.com>
Not all Kirkwood systems have the Marvell MV88E6XXX switches.
Drop those from the generic config and add them as modules
in the systems that have it.
This was inferred by inspecting the upstream DTS files for any
mv88e* strings and adding the mv88e6xxx kmod package to those
that have an upstream device tree with an MV88E6xxx switch
and an OpenWrt image target.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This is using mac-base and so a 0 needs to be added.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17274
Signed-off-by: Robert Marko <robimarko@gmail.com>
Images for xrx200 8M flash are either not building due to image
size (TD-W8970, TD-W8980) or building such that the available
free space in the overlayfs is too little to be useful.
To keep images for these devices buildable, move them into a
small flash variant of the xrx200 subtarget. As these devices
are NOR flash only, remove NAND and UBI references from the
kernel config to gain some additional image size reduction.
The apparent 8M flash devices Arcadyan VGV7510KW22-brn,
Arcadyan VGV7519-brn and Lantiq Easy80920-nor seem to exist in
order to create special "factory" installation images for these
devices (which actually have larger flash: 16MB for the
Arcardyan devices; 64MB for the Lantiq device). As a
considerable amount of surgery would appear to be required to
the uboot-lantiq package structure to separate the "factory"
from the "sysupgrade" device recipes for these devices they
remain in the xrx200 target - if factory images aren't now
created, 23.05.x factory images should suffice for initial
installation.
Tested on: Netgear DM200, TP-Link TD-W8980,
AVM Fritz7490 (xrx200 subtarget: image build only)
Fixes: https://github.com/openwrt/openwrt/issues/16761
Signed-off-by: Andrew MacIntyre <andymac@pcug.org.au>
Link: https://github.com/openwrt/openwrt/pull/17113
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The PHY can handle turning off the GPIOs when turning off all USB ports.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17192
Signed-off-by: Robert Marko <robimarko@gmail.com>
Specifications:
- Device: ASUS 4g-AX56
- SoC: MT7621AT
- Flash: 128MB
- RAM: 512MB
- Switch: 1 WAN, 4 LAN (10/100/1000 Mbps)
- WiFi: MT7905 2x2 2.4G + MT7975 2x2 5G
- LTE : Fibocom FG621-EA
- LEDs: 1x POWER (white, configurable)
1x 2.4G (white, not configurable)
1x 5G (white, not configurable)
1x WAN (white, not configurable)
1x 3G/4G (white, not configurable)
3x signal (white, not configurable)
Flash by U-Boot TFTP method:
- Configure your PC with IP 192.168.0.2
- Set up TFTP server and put the factory.bin image on your PC
- Connect serial port(rate:115200) and turn on AP, then interrupt "U-Boot Boot Menu" by hitting any key
Select "2. Upgrade firmware"
Press enter when show "Run firmware after upgrading? (Y/n):"
Select 0 for TFTP method
Input U-Boot's IP address: 192.168.0.1
Input TFTP server's IP address: 192.168.0.2
Input IP netmask: 255.255.255.0
Input file name: openwrt-ramips-mt7621-asus_4g-ax56-squashfs-factory.bin
- Restart AP aftre see the log "Firmware upgrade completed!"
Notice:
- LTE module is disable after flash openwrt image so you must active LTE by following two AT command
echo -e "AT+GTAUTOCONNECT=1\r\n" > /dev/ttyUSB0
echo -e "AT+GTRNDIS=1,1\r\n" > /dev/ttyUSB0
- After finish AT command once, you don't need to input command later even if reboot/restore default
Signed-off-by: Chuncheng Chen <ccchen1984@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16752
Signed-off-by: John Crispin <john@phrozen.org>
Hardware
* Mediatek MT7620A + Mediatek MT7610EN
* 64MB RAM
* 8MB NAND (Winbond 25064FVSIG )
Both 2.4GHZ and 5GHZ are working, it is enabled by default since there is no
physical ethernet port in the device.
All LED's and buttons work.
UART: 57600 8N1 3.3V
Installation
Upload the openwrt-ramips-mt7620-trendnet_tha103ac-initramfs-kernel.bin via
the manufacturer firmware upgrade page on the device.
Upon reboot wait +- 3 mins until the green power LED is not flashing anymore
(do not be tempted to switch the device off while the LED is flashing, unless
you are ready for soldering and TTL) and then press the WPS button to enable
the default OpenWrt Wifi AP, the BLUE wifi LED will start flash.
Then install openwrt-ramips-mt7620-trendnet_tha103ac-squashfs-sysupgrade.bin
via OpenWrt.
The integrated power monitoring and relay do not work in OpenWrt as the PL7223
chip source/documentation is unavailable.
Recovery
Mis-configuration can be dealt with using the RESET button to reset to factory,
worst case scenario will require some serious work and soldering, there's pads
on the PCB for both the UART and ETH0, and I soldered and tested that it does
work.
You will have to power the board using the header pins GND & 5V, see the 8-pin
header socket.
Signed-off-by: Die Peter Pan <diepeterpan@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17114
Signed-off-by: John Crispin <john@phrozen.org>
The original ar71xx version of this device used 1002 as mac address for
both ethernet and wireless. The ath79 version inexplicably changes this
to 2, which seems to be done nowhere else in ath79, indicating it's
bogus.
Restore previous ar71xx assignment. 1002 is used as an ethernet
interface with some other devices as well.
Also remove the bogus caldata userspace extraction. The size is bogus
and it's already handled in dts.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17083
Signed-off-by: John Crispin <john@phrozen.org>
NRadio C8-668GL is a Wi-Fi 6 5G cellular router based on MediaTek MT7981B SoC.
- **SoC**: MediaTek MT7981B (2x Cortex-A53, 1.3GHz)
- **RAM**: Nanya NT5AD512M16C4-JR 1GB DDR4
- **Flash**: ESMT FC51L08SFY3A 8GB eMMC
- **Ethernet**:
- 1x 2.5GbE (via GMAC0 and GPY211 PHY, shared with MT7531AE)
- 3x 10/100/1000 Mbps (via MT7531AE, connected to GMAC0)
- 5G Modem: GMAC1 (via GPY211 PHY - RTL8125BG - RM520N-GL)
- **Wi-Fi**: MediaTek MT7976CN (2.4GHz/5GHz, 802.11ax, 2x2 MIMO, AX3000)
- **Buttons**: Reset, WPS
- **LEDs**: Power, 5G, 4G, WiFi
- **SIM Slot**: 1x Nano SIM
- **5G Modem**: Quectel RM520N-GL (Snapdragon™ X62)
- **Power**: 12V/2A DC, 5.5×2.1 connector
The MAC addresses are derived from the `fac_mac` field in the `bdinfo` partition, formatted as `fac_mac = HWMAC`. The allocation is as follows:
| Vendor | OpenWrt Interface | Address | Notes |
|---------|-------------------|---------------|------------------------------------------------|
| LAN | br-lan | Label MAC | Default |
| WAN | lan4 | Label MAC+1 | Only when lan4 is switched to WAN |
| 2.4GHz | phy0-ap0 | Label MAC | |
| 5GHz | phy1-ap0 | Label MAC | (Local Admin bit set) |
| Modem | eth1 | Label MAC+2 | |
1. Log in to the router via `http://192.168.66.1`/.
2. Upgrade the official firmware to dual-system mode.
3. Select **Burn second system** and upload the `sysupgrade.bin` image.
- Download the image from the OpenWrt build system or build it yourself using the OpenWrt buildroot.
4. Wait for 30 seconds and click **Switch system**.
5. The device will reboot and switch to OpenWrt.
Set the U-Boot environment variable `boot_system=0` and reboot:
```bash
fw_setenv boot_system 0
```
Power off the router, hold the **WPS button**, and power it back on.
1. Rename the stock firmware file to **`recovery.bin`**.
2. Set your PC's Ethernet IP to **192.168.1.88** and connect it to the lan1 port on the router.
3. Run a TFTP server and place the `recovery.bin` file in its root directory.
4. Power off the router, press and hold the **Reset button**, and power it back on.
5. Release the Reset button when the TFTP server shows activity.
6. Wait for the router to flash the firmware and reboot automatically.
- By default, `lan4` is part of `br-lan` and uses the label MAC address.
- To query the RM520N-GL module, use the following command:
```bash
cat /dev/ttyUSB2 & printf 'ATI\r\n' > /dev/ttyUSB2
```
Signed-off-by: Yaoguang Bai <0xdeadc0de@badguys.club>
Link: https://github.com/openwrt/openwrt/pull/17093
Signed-off-by: John Crispin <john@phrozen.org>
Upstream uses devm_reset_control_array_get_optional_shared, which does
not use names. reset-names is also not specified in the documentation.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17118
Signed-off-by: John Crispin <john@phrozen.org>
Both generic-ehci.yaml and generic-ohci.yaml state that phy-names is to
only be usb.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17118
Signed-off-by: John Crispin <john@phrozen.org>
This matches the upstream PHY driver, which removed it.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17118
Signed-off-by: John Crispin <john@phrozen.org>
One is already present. The other one can be implemented in terms of the
PHY.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17250
Signed-off-by: John Crispin <john@phrozen.org>
Instead of using regulator-output to manually control USB GPIO, let the
PHY handle it.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17221
Signed-off-by: John Crispin <john@phrozen.org>
We have seen hung devices and failures during SPI transactions on
Fritzbox devices with a gluon based freifunk network. We have narrowed
down that disabling DMA for spi fixes the problem, so disable dma for
the SPI controller on the Fritzbox 4040.
Signed-off-by: Rouven Czerwinski <rouven@czerwinskis.de>
Link: https://github.com/openwrt/openwrt/pull/15966
Signed-off-by: John Crispin <john@phrozen.org>
Use ath11k_patch_mac and ath11k_set_macflag functions
instead of fix_wifi_mac script.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/17230
Signed-off-by: Robert Marko <robimarko@gmail.com>
Change partition table in dts file.
Change DEVICE_COMPAT_VERSION
Enable automatic build.
To take advantage of the bigger kernel partition,
the uboot environment has to be changed:
setenv nboot 'nand read 0x81000000 0x60000 0x500000; bootm 0x81000000'
setenv bootcmd 'run nboot'
saveenv
Of course you need a u-boot capable of handling this.
The u-boot discussed in this forum thread:
https://forum.openwrt.org/t/zyxel-p2812hnu-f1-u-boot/100281
should be able to handle kernels up to an uncompressed size of 16MiB.
Signed-off-by: Isaac de Wolff <idewolff@gmx.com>
Link: https://github.com/openwrt/openwrt/pull/17209
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The device path to the devices changed. Migrate the wifi
configurations from the old path to the new one. This is needed to
migrate Wireless configurations from OpenWrt 23.05 to OpenWrt 24.10.
This script is based on these two files:
target/linux/ramips/mt7621/base-files/etc/hotplug.d/ieee80211/05-wifi-migrate
target/linux/qualcommax/ipq807x/base-files/etc/hotplug.d/ieee80211/05-wifi-migrate
Fixes: 0ef9274721 ("mediatek: filogic: move mt7981 on-SoC blocks to "soc" node in DT")
Fixes: https://github.com/openwrt/openwrt/issues/17174
Link: https://github.com/openwrt/openwrt/pull/17210
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The vendor U-Boot on the Cudy WR3000 assign random mac addresses on boot
and set the 'local-mac-address' property which prevents Openwrt from
assigning the correct address from evmem.
This patch removes the alias for ethernet0 so that U-Boot doesn't add
the property.
Related to: a55ab9e134 ("mediatek: filogic: prevent faulty mac address assignment")
Fixes: https://github.com/openwrt/openwrt/issues/15587
Signed-off-by: Ondřej Niesner <ondra.niesner@seznam.cz>
Link: https://github.com/openwrt/openwrt/pull/17201
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
