openwrt

mirror of https://github.com/openwrt/openwrt.git synced 2024-12-25 00:11:13 +00:00

Author	SHA1	Message	Date
Joe Mullally	4965cbd259	ath79: tiny: Do not build TPLink WPA8630Pv2 by default 22.03.1+ and snapshot builds no longer fit the 6M flash space available for these models. This disables failing buildbot image builds for these devices. Images can still be built manually with ImageBuilder. Signed-off-by: Joe Mullally <jwmullally@gmail.com>	2023-01-06 18:52:01 +01:00
Michael Pratt	e085812a7d	ath79: add support for Fortinet FAP-221-B FCC ID: U2M-CAP4100AG Fortinet FAP-221-B is an indoor access point with 1 Gb ethernet port, dual-band wireless, internal antenna plates, and 802.3at PoE+ Hardware and board design from Senao Specification: - AR9344 SOC 2G 2x2, 5G 2x2, 25 MHz CLK - AR9382 WLAN 2G 2x2 PCIe, 40 MHz CLK - AR8035-A PHY RGMII, PoE+ IN, 25 MHz CLK - 16 MB FLASH MX25L12845EMI-10G - 2x 32 MB RAM W9725G6JB-25 - UART at J11 populated, 9600 baud - 6 LEDs, 1 button power, ethernet, wlan, reset Note: ethernet LEDs are not enabled because a new netifd hotplug is required in order to operate like OEM. Board has 1 amber and 1 green for each of the 3 case viewports. MAC addresses: 1 MAC Address in flash at end of uboot ASCII encoded, no delimiters Labeled as "MAC Address" on case OEM firmware sets offsets 1 and 8 for wlan eth0 :1e uboot 0x3ff80 phy0 :1f uboot 0x3ff80 +1 phy1 :26 uboot 0x3ff80 +8 Serial Access:* Pinout: (arrow) VCC GND RX TX Pins are populated with a header and traces not blocked. Bootloader is set to 9600 baud, 8 data, 1 stop. Console Access: Bootloader: Interrupt boot with Ctrl+C Press "k" and enter password "1" OR Hold reset button for 5 sec during power on Interrupt the TFTP transfer with Ctrl+C to print commands available, enter "help" OEM: default username is "admin", password blank telnet is available at default address 192.168.1.2 serial is available with baud 9600 to print commands available, enter "help" or tab-tab (busybox list of commands) Installation: Use factory.bin with OEM upgrade procedures OR Use initramfs.bin with uboot TFTP commands. Then perform a sysupgrade with sysupgrade.bin TFTP Recovery: Using serial console, load initramfs.bin using TFTP to boot openwrt without touching the flash. TFTP is not reliable due to bugged bootloader, set MTU to 600 and try many times. If your TFTP server supports setting block size, higher block size is better. Splitting the file into 1 MB parts may be necessary example: $ tftpboot 0x80100000 image1.bin $ tftpboot 0x80200000 image2.bin $ tftpboot 0x80300000 image3.bin $ tftpboot 0x80400000 image4.bin $ tftpboot 0x80500000 image5.bin $ tftpboot 0x80600000 image6.bin $ bootm 0x80100000 Return to OEM: The best way to return to OEM firmware is to have a copy of the MTD partitions before flashing Openwrt. Backup copies should be made of partitions "fwconcat0", "loader", and "fwconcat1" which together is the same flash range as OEM's "rootfs" and "uimage" by loading an initramfs.bin and using LuCI to download the mtdblocks. It is also possible to extract from the OEM firmware upgrade image by splitting it up in parts of lengths that correspond to the partitions in openwrt and write them to flash, after gzip decompression. After writing to the firmware partitions, erase the "reserved" partition and reboot. OEM firmware image format: Images from Fortinet for this device ending with the suffix .out are actually a .gz file The gzip metadata stores the original filename before compression, which is a special string used to verify the image during OEM upgrade. After gzip decompression, the resulting file is an exact copy of the MTD partitions "rootfs" and "uimage" combined in the same order and size that they appear in /proc/mtd and as they are on flash. OEM upgrade is performed by a customized busybox with the command "upgrade". Another binary, "restore" is a wrapper for busybox's "tftp" and "upgrade". Signed-off-by: Michael Pratt <mcpratt@pm.me>	2023-01-06 15:34:07 +01:00
Michael Pratt	8342c092a0	ath79: use lzma-loader for Senao initramfs images Some vendors of Senao boards have put a bootloader that cannot handle both large gzip or large lzma files. There is no disadvantage by doing this for all of them. Signed-off-by: Michael Pratt <mcpratt@pm.me>	2023-01-06 15:34:07 +01:00
Nick Hainke	aa6c8c38ea	ath79: convert Netgear WNDAP360 WiFis to nvmem-cells Pull the calibration data from the nvmem subsystem. This allows us to move userspace caldata extraction into the device-tree definition. Merge art into partition node. Signed-off-by: Nick Hainke <vincent@systemli.org>	2023-01-04 23:59:09 +01:00
Alexander Couzens	17c6fb1054	ath79: image: don't depend on other COMPILE targets A device COMPILE target should not depend on another COMPILE. Otherwise race condition may happen. The loader is very small. Compiling it twice shouldn't have a huge impact. Signed-off-by: Alexander Couzens <lynxis@fe80.eu>	2022-12-19 12:27:35 +00:00
Davide Fioravanti	d9566d059c	ath79: add support for KuWFi C910 KuWFi C910 is an 802.11n (300N) indoor router with LTE support. I can't find anywhere the OEM firmware. So if you want to restore the original firmware you must do a dump before the OpenWrt flash. According to the U-Boot, the board name is Iyunlink MINI_V2. Hardware -------- SoC: Qualcomm QCA9533 650/400/200/25/25 MHz (CPU/RAM/AHB/SPI/REF) RAM: 128 MB DDR2 16-bit CL3-4-4-10 (Nanya NT5TU64M16HG-AC) FLASH: 16 MB Winbond W25Q128 ETH: - 2x 100M LAN (QCA9533 internal AR8229 switch, eth0) - 1x 100M WAN (QCA9533 internal PHY, eth1) WIFI: - 2.4GHz: 1x QCA9533 2T2R (b/g/n) - 2 external non detachable antennas (near the power barrel side) LTE: - Quectel EC200T-EU (or -CN or -AU depending on markets) - 2 external non detachable antennas (near the sim slot side) BTN: - 1x Reset button LEDS: - 5x White leds (Power, Wifi, Wan, Lan1, Lan2) - 1x RGB led (Internet) UART: 115200-8-N-1 (Starting from lan ports in order: GND, RX, TX, VCC) Everything works correctly. MAC Addresses ------------- LAN XX:XX:XX:XX:XX:48 (art@0x1002) WAN XX:XX:XX:XX:XX:49 (art@0x1002 + 1) WIFI XX:XX:XX:XX:XX:48 LABEL XX:XX:XX:XX:XX:48 Installation ------------ Turn the router on while pressing the reset button for 4 seconds. You can simply count the flashes of the first lan led. (See notes) If done correctly you should see the first lan led glowing slowly and you should be able to enter the U-Boot web interface. Click on the second tab ("固件") and select the -factory.bin firmware then click "Update firmware". A screen "Update in progress" should appear. After few minutes the flash should be completed. This procedure can be used also to recover the router in case of soft brick. Backup the original firmware ---------------------------- The following steps are intended for a linux pc. However using the right software this guide should also work for Windows and MacOS. 1) Install a tftp server on your pc. For example tftpd-hpa. 2) Create two empty files in your tftp folder called: kuwfi_c910_all_nor.bin kuwfi_c910_firmware_only.bin 3) Give global write permissions to these files: chmod 666 kuwfi_c910_all_nor.bin chmod 666 kuwfi_c910_firmware_only.bin 4) Start a netcat session on your pc with this command: nc -u -p 6666 192.168.1.1 6666 5) Set the static address on your pc: 192.168.1.2. Connect the router to your pc. 6) Turn the router on while pressing the reset button for 8-9 seconds. You can simply count the flashes of the first lan led. If you press the reset button for too many seconds it will continue the normal boot, so you have to restart the router. (See notes) 7) If done correctly you should see the U-Boot network console and you should see the following lines on the netcat session: Version and build date: U-Boot 1.1.4-55f1bca8-dirty, 2020-05-07 Modification by: Piotr Dymacz <piotr@dymacz.pl> https://github.com/pepe2k/u-boot_mod u-boot> 8) Start the transfer of the whole NOR: tftpput 0x9f000000 0x1000000 kuwfi_c910_all_nor.bin 9) The router should start the transfer and it should end with a message like this (pay attention to the bytes transferred): TFTP transfer complete! Bytes transferred: 16777216 (0x1000000) 10) Repeat the same transfer for the firmware: tftpput 0x9f050000 0xfa0000 kuwfi_c910_firmware_only.bin 11) The router should start the transfer and it should end with a message like this (pay attention to the bytes transferred): TFTP transfer complete! Bytes transferred: 16384000 (0xfa0000) 12) Now you have the backup for the whole nor and for the firmware partition. If you want to restore the OEM firmware from OpenWrt you have to flash the kuwfi_c910_firmware_only.bin from the U-Boot web interface. WARNING: Don't use the kuwfi_c910_all_nor.bin file. This file is only useful if you manage to hard brick the router or you damage the art partition (ask on the forum) Notes ----- This router (or at least my unit) has the pepe2k's U-Boot. It's a modded U-Boot version with a lot of cool features. You can read more here: https://github.com/pepe2k/u-boot_mod With this version of U-Boot, pushing the reset button while turning on the router starts different tools: - 3-5 seconds: U-Boot web interface that can be used to replace the firmware, the art or the U-Boot itself - 5-7 seconds: U-Boot uart console - 7-10 seconds: U-Boot network console - 11+ seconds: Normal boot The LTE modem can be used in cdc_ether (ECM) or RNDIS mode. The default mode is ECM and in this commit only the ECM software is included. In order to set RNDIS mode you must use this AT command: AT+QCFG="usbnet",3 In order to use again the ECM mode you must use this AT command: AT+QCFG="usbnet",1 Look for "Quectel_EC200T_Linux_USB_Driver_User_Guide_V1.0.pdf" for other AT commands Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>	2022-12-17 22:28:10 +01:00
Andrew Cameron	550e5b2184	ath79: add support for TP-Link CPE605-v1 TP-Link CPE605-v1 is an outdoor wireless CPE for 5 GHz with one Ethernet port based on Atheros AR9344 Specifications: - 560/450/225 MHz (CPU/DDR/AHB) - 1x 10/100 Mbps Ethernet - 64 MB of DDR2 RAM - 8 MB of SPI-NOR Flash - 23dBi high-gain directional antenna and a dedicated metal reflector - Power, LAN, WLAN5G green LEDs - 3x green RSSI LEDs Flashing instructions: Flash factory image through stock firmware WEB UI or through TFTP To get to TFTP recovery just hold reset button while powering on for around 4-5 seconds and release. Rename factory image to recovery.bin Stock TFTP server IP:192.168.0.100 Stock device TFTP adress:192.168.0.254 Signed-off-by: Andrew Cameron <apcameron@softhome.net>	2022-12-13 23:17:27 +01:00
Shiji Yang	3c1512a25d	ath79: optimize the firmware recipe for Netgear NAND devices 1. Drop useless character '0xff' before fake filesystem header. 2. Reduce useless padding to shrink the size of the sysupgrade image. 3. Do not check the size of sysupgrade image. It does not make sense to check the size of a compressed package. 4. Do not take the size of netgear header into account because it will not be written to Flash. 5. Use the default lzma compression dictionary parameter '-d24' to get better performance. Tested on Netgear R6100 Signed-off-by: Shiji Yang <yangshiji66@qq.com>	2022-12-06 23:11:23 +01:00
Will Moss	a58146d452	ath79: D-Link DIR-825 B1 add factory.bin recipe - Bring back factory.bin image which was missing after porting device to ath79 target - Use default sysupgrade.bin image recipe - Adjust max image size according to new firmware partition size after "ath79: expand rootfs for DIR-825-B1 with unused space (`aca8bb5`)" changes - Remove support of upgrading from version 19.07, because partition size changes mentioned above Signed-off-by: Will Moss <willormos@gmail.com>	2022-11-27 13:18:29 +01:00
Michael Pratt	6de9287abd	ath79: add support for Senao Engenius EAP1750H FCC ID: A8J-EAP1750H Engenius EAP1750H is an indoor wireless access point with 1 Gb ethernet port, dual-band wireless, internal antenna plates, and 802.3at PoE+ Specification: - QCA9558 SOC - QCA9880 WLAN PCI card, 5 GHz, 3x3, 26dBm - AR8035-A PHY RGMII GbE with PoE+ IN - 40 MHz clock - 16 MB FLASH MX25L12845EMI-10G - 2x 64 MB RAM NT5TU32M16FG - UART at J10 populated - 4 internal antenna plates (5 dbi, omni-directional) - 5 LEDs, 1 button (power, eth0, 2G, 5G, WPS) (reset) MAC addresses: MAC addresses are labeled as ETH, 2.4G, and 5GHz Only one Vendor MAC address in flash eth0 ETH :fb art 0x0 phy1 2.4G :fc --- phy0 5GHz :fd --- Serial Access:* the RX line on the board for UART is shorted to ground by resistor R176 therefore it must be removed to use the console but it is not necessary to remove to view boot log optionally, R175 can be replaced with a solder bridge short the resistors R175 and R176 are next to the UART RX pin at J10 Installation: 2 ways to flash factory.bin from OEM: Method 1: Firmware upgrade page: OEM webpage at 192.168.1.1 username and password "admin" Navigate to "Firmware Upgrade" page from left pane Click Browse and select the factory.bin image Upload and verify checksum Click Continue to confirm and wait 3 minutes Method 2: Serial to load Failsafe webpage: After connecting to serial console and rebooting... Interrupt uboot with any key pressed rapidly execute `run failsafe_boot` OR `bootm 0x9fd70000` wait a minute connect to ethernet and navigate to "192.168.1.1/index.htm" Select the factory.bin image and upload wait about 3 minutes Return to OEM: If you have a serial cable, see Serial Failsafe instructions otherwise, uboot-env can be used to make uboot load the failsafe image ssh into openwrt and run `fw_setenv rootfs_checksum 0` reboot, wait 3 minutes connect to ethernet and navigate to 192.168.1.1/index.htm select OEM firmware image from Engenius and click upgrade TFTP recovery: Requires serial console, reset button does nothing rename initramfs to 'vmlinux-art-ramdisk' make available on TFTP server at 192.168.1.101 power board, interrupt boot execute tftpboot and bootm 0x81000000 NOTE: TFTP is not reliable due to bugged bootloader set MTU to 600 and try many times if your TFTP server supports setting block size higher block size is better. Format of OEM firmware image: The OEM software of EAP1750H is a heavily modified version of Openwrt Kamikaze. One of the many modifications is to the sysupgrade program. Image verification is performed simply by the successful ungzip and untar of the supplied file and name check and header verification of the resulting contents. To form a factory.bin that is accepted by OEM Openwrt build, the kernel and rootfs must have specific names... openwrt-ar71xx-generic-eap1750h-uImage-lzma.bin openwrt-ar71xx-generic-eap1750h-root.squashfs and begin with the respective headers (uImage, squashfs). Then the files must be tarballed and gzipped. The resulting binary is actually a tar.gz file in disguise. This can be verified by using binwalk on the OEM firmware images, ungzipping then untaring. Newer EnGenius software requires more checks but their script includes a way to skip them, otherwise the tar must include a text file with the version and md5sums in a deprecated format. The OEM upgrade script is at /etc/fwupgrade.sh. OKLI kernel loader is required because the OEM software expects the kernel to be no greater than 1536k and the factory.bin upgrade procedure would otherwise overwrite part of the kernel when writing rootfs. Note on PLL-data cells: The default PLL register values will not work because of the external AR8035 switch between the SOC and the ethernet port. For QCA955x series, the PLL registers for eth0 and eth1 can be see in the DTSI as 0x28 and 0x48 respectively. Therefore the PLL registers can be read from uboot for each link speed after attempting tftpboot or another network action using that link speed with `md 0x18050028 1` and `md 0x18050048 1`. The clock delay required for RGMII can be applied at the PHY side, using the at803x driver `phy-mode`. Therefore the PLL registers for GMAC0 do not need the bits for delay on the MAC side. This is possible due to fixes in at803x driver since Linux 5.1 and 5.3 Signed-off-by: Michael Pratt <mcpratt@pm.me>	2022-11-27 13:18:29 +01:00
Roger Pueyo Centelles	5a1d7d8c1b	ath79: disable image building for Ubiquiti EdgeSwitch 8XP The downstream OpenWrt driver for the BCM53128 switch ceased to work, rendering the 8 LAN ports of the device unusable. This commit disables image building while the problem is being solved. See issue #10374 for more details. Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>	2022-11-20 16:24:24 +01:00
Moritz Warning	dc7d431b60	treewide: uniform vendor name for devolo The company name is lower case on the website (https://www.devolo.de) and in product names. Signed-off-by: Moritz Warning <moritzwarning@web.de>	2022-11-18 20:27:52 +01:00
Lech Perczak	6fdeb48c1e	ath79: support Ruckus ZoneFlex 7025 Ruckus ZoneFlex 7025 is a single 2.4GHz radio 802.11n 1x1 enterprise access point with built-in Ethernet switch, in an electrical outlet form factor. Hardware highligts: - CPU: Atheros AR7240 SoC at 400 MHz - RAM: 64MB DDR2 - Flash: 16MB SPI-NOR - Wi-Fi: AR9285 built-in 2.4GHz 1x1 radio - Ethernet: single Fast Ethernet port inside the electrical enclosure, coupled with internal LSA connector for direct wiring, four external Fast Ethernet ports on the lower side of the device. - PoE: 802.3af PD input inside the electrical box. 802.3af PSE output on the LAN4 port, capable of sourcing class 0 or class 2 devices, depending on power supply capacity. - External 8P8C pass-through connectors on the back and right side of the device - Standalone 48V power input on the side, through 2/1mm micro DC barrel jack Serial console: 115200-8-N-1 on internal JP1 header. Pinout: ---------- JP1 \|5\|4\|3\|2\|1\| ---------- Pin 1 is near the "H1" marking. 1 - RX 2 - n/c 3 - VCC (3.3V) 4 - GND 5 - TX Installation: There are two methods of installation: - Using serial console [1] - requires some disassembly, 3.3V USB-Serial adapter, TFTP server, and removing a single T10 screw, but with much less manual steps, and is generally recommended, being safer. - Using stock firmware root shell exploit, SSH and TFTP [2]. Does not work on some rare versions of stock firmware. A more involved, and requires installing `mkenvimage` from u-boot-tools package if you choose to rebuild your own environment, but can be used without disassembly or removal from installation point, if you have the credentials. If for some reason, size of your sysupgrade image exceeds 13312kB, proceed with method [1]. For official images this is not likely to happen ever. [1] Using serial console: 0. Connect serial console to H1 header. Ensure the serial converter does not back-power the board, otherwise it will fail to boot. 1. Power-on the board. Then quickly connect serial converter to PC and hit Ctrl+C in the terminal to break boot sequence. If you're lucky, you'll enter U-boot shell. Then skip to point 3. Connection parameters are 115200-8-N-1. 2. Allow the board to boot. Press the reset button, so the board reboots into U-boot again and go back to point 1. 3. Set the "bootcmd" variable to disable the dual-boot feature of the system and ensure that uImage is loaded. This is critical step, and needs to be done only on initial installation. > setenv bootcmd "bootm 0x9f040000" > saveenv 4. Boot the OpenWrt initramfs using TFTP. Replace IP addresses as needed: > setenv serverip 192.168.1.2 > setenv ipaddr 192.168.1.1 > tftpboot 0x81000000 openwrt-ath79-generic-ruckus_zf7025-initramfs-kernel.bin > bootm 0x81000000 5. Optional, but highly recommended: back up contents of "firmware" partition: $ ssh root@192.168.1.1 cat /dev/mtd1 > ruckus_zf7025_fw1_backup.bin 6. Copy over sysupgrade image, and perform actual installation. OpenWrt shall boot from flash afterwards: $ ssh root@192.168.1.1 # sysupgrade -n openwrt-ath79-generic-ruckus_zf7025-squashfs-sysupgrade.bin [2] Using stock root shell: 0. Reset the device to factory defaullts. Power-on the device and after it boots, hold the reset button near Ethernet connectors for 5 seconds. 1. Connect the device to the network. It will acquire address over DHCP, so either find its address using list of DHCP leases by looking for label MAC address, or try finding it by scanning for SSH port: $ nmap 10.42.0.0/24 -p22 From now on, we assume your computer has address 10.42.0.1 and the device has address 10.42.0.254. 2. Set up a TFTP server on your computer. We assume that TFTP server root is at /srv/tftp. 3. Obtain root shell. Connect to the device over SSH. The SSHD ond the frmware is pretty ancient and requires enabling HMAC-MD5. $ ssh 10.42.0.254 \ -o UserKnownHostsFile=/dev/null \ -o StrictHostKeyCheking=no \ -o MACs=hmac-md5 Login. User is "super", password is "sp-admin". Now execute a hidden command: Ruckus It is case-sensitive. Copy and paste the following string, including quotes. There will be no output on the console for that. ";/bin/sh;" Hit "enter". The AP will respond with: grrrr OK Now execute another hidden command: !v54! At "What's your chow?" prompt just hit "enter". Congratulations, you should now be dropped to Busybox shell with root permissions. 4. Optional, but highly recommended: backup the flash contents before installation. At your PC ensure the device can write the firmware over TFTP: $ sudo touch /srv/tftp/ruckus_zf7025_firmware{1,2}.bin $ sudo chmod 666 /srv/tftp/ruckus_zf7025_firmware{1,2}.bin Locate partitions for primary and secondary firmware image. NEVER blindly copy over MTD nodes, because MTD indices change depending on the currently active firmware, and all partitions are writable! # grep rcks_wlan /proc/mtd Copy over both images using TFTP, this will be useful in case you'd like to return to stock FW in future. Make sure to backup both, as OpenWrt uses bot firmwre partitions for storage! # tftp -l /dev/<rcks_wlan.main_mtd> -r ruckus_zf7025_firmware1.bin -p 10.42.0.1 # tftp -l /dev/<rcks_wlan.bkup_mtd> -r ruckus_zf7025_firmware2.bin -p 10.42.0.1 When the command finishes, copy over the dump to a safe place for storage. $ cp /srv/tftp/ruckus_zf7025_firmware{1,2}.bin ~/ 5. Ensure the system is running from the BACKUP image, i.e. from rcks_wlan.bkup partition or "image 2". Otherwise the installation WILL fail, and you will need to access mtd0 device to write image which risks overwriting the bootloader, and so is not covered here and not supported. Switching to backup firmware can be achieved by executing a few consecutive reboots of the device, or by updating the stock firmware. The system will boot from the image it was not running from previously. Stock firmware available to update was conveniently dumped in point 4 :-) 6. Prepare U-boot environment image. Install u-boot-tools package. Alternatively, if you build your own images, OpenWrt provides mkenvimage in host staging directory as well. It is recommended to extract environment from the device, and modify it, rather then relying on defaults: $ sudo touch /srv/tftp/u-boot-env.bin $ sudo chmod 666 /srv/tftp/u-boot-env.bin On the device, find the MTD partition on which environment resides. Beware, it may change depending on currently active firmware image! # grep u-boot-env /proc/mtd Now, copy over the partition # tftp -l /dev/mtd<N> -r u-boot-env.bin -p 10.42.0.1 Store the stock environment in a safe place: $ cp /srv/tftp/u-boot-env.bin ~/ Extract the values from the dump: $ strings u-boot-env.bin \| tee u-boot-env.txt Now clean up the debris at the end of output, you should end up with each variable defined once. After that, set the bootcmd variable like this: bootcmd=bootm 0x9f040000 You should end up with something like this: bootcmd=bootm 0x9f040000 bootargs=console=ttyS0,115200 rootfstype=squashfs init=/sbin/init baudrate=115200 ethaddr=0x00:0xaa:0xbb:0xcc:0xdd:0xee mtdparts=mtdparts=ar7100-nor0:256k(u-boot),7168k(rcks_wlan.main),7168k(rcks_wlan.bkup),1280k(datafs),256k(u-boot-env) mtdids=nor0=ar7100-nor0 bootdelay=2 filesize=52e000 fileaddr=81000000 ethact=eth0 stdin=serial stdout=serial stderr=serial partition=nor0,0 mtddevnum=0 mtddevname=u-boot ipaddr=192.168.0.1 serverip=192.168.0.2 stderr=serial ethact=eth0 These are the defaults, you can use most likely just this as input to mkenvimage. Now, create environment image and copy it over to TFTP root: $ mkenvimage -s 0x40000 -b -o u-boot-env.bin u-boot-env.txt $ sudo cp u-boot-env.bin /srv/tftp This is the same image, gzipped and base64-encoded: H4sICOLMEGMAA3UtYm9vdC1lbnYtbmV3LmJpbgDt0E1u00AUAGDfgm2XDUrTsUV/pTkFSxZoEk+o lcQJtlNaLsURwU4FikDiBN+3eDNvLL/3Zt5/+vFuud8Pq10dp3V3EV4e1uFDGBXTQeq+9HG1b/v9 NsdheP0Y5mV5U4Vw0Y1f1/3wesix/3pM/dO6v2jaZojX/bJpr6dtsUzHuktDjm//FHl4SnXdxfAS wmN4SWkMy+UYVqsx1PUYci52Q31I3dDHP5vU3ZUhXLX7LjxWN7eby+PVNNxsflfe3m8uu9Wm//xt m9rFLjXtv6fLzfEwm5fVfdhc1mlI6342Pytzldvn2dS1qfs49Tjvd3qFOm/Ta6yKdbPNffM9x5sq Ty805acL3Zfh5HTD1RDHJRT9WLGNfe6atJ2S/XE4y3LX/c6mSzZDs29P3edhmqXOz+1xF//s0y7H t3GL5nDqWT5Ui/Gii7Aoi7HQ81jrcHZY/dXkfLLiJwAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAD8 xy8jb4zOAAAEAA== 7. Perform actual installation. Copy over OpenWrt sysupgrade image to TFTP root: $ sudo cp openwrt-ath79-generic-ruckus_zf7025-squashfs-sysupgrade.bin /srv/tftp Now load both to the device over TFTP: # tftp -l /tmp/u-boot-env.bin -r u-boot-env.bin -g 10.42.0.1 # tftp -l /tmp/openwrt.bin -r openwrt-ath79-generic-ruckus_zf7025-squashfs-sysupgrade.bin -g 10.42.0.1 Verify checksums of both images to ensure the transfer over TFTP was completed: # sha256sum /tmp/u-boot-env.bin /tmp/openwrt.bin And compare it against source images: $ sha256sum /srv/tftp/u-boot-env.bin /srv/tftp/openwrt-ath79-generic-ruckus_zf7025-squashfs-sysupgrade.bin Locate MTD partition of the primary image: # grep rcks_wlan.main /proc/mtd Now, write the images in place. Write U-boot environment last, so unit still can boot from backup image, should power failure occur during this. Replace MTD placeholders with real MTD nodes: # flashcp /tmp/openwrt.bin /dev/<rcks_wlan.main_mtd> # flashcp /tmp/u-boot-env.bin /dev/<u-boot-env_mtd> Finally, reboot the device. The device should directly boot into OpenWrt. Look for the characteristic power LED blinking pattern. # reboot -f After unit boots, it should be available at the usual 192.168.1.1/24. Return to factory firmware: 1. Boot into OpenWrt initramfs as for initial installation. To do that without disassembly, you can write an initramfs image to the device using 'sysupgrade -F' first. 2. Unset the "bootcmd" variable: fw_setenv bootcmd "" 3. Concatenate the firmware backups, if you took them during installation using method 2: $ cat ruckus_zf7025_fw1_backup.bin ruckus_zf7025_fw2_backup.bin > ruckus_zf7025_backup.bin 3. Write factory images downloaded from manufacturer website into fwconcat0 and fwconcat1 MTD partitions, or restore backup you took before installation: # mtd write ruckus_zf7025_backup.bin /dev/mtd1 4. Reboot the system, it should load into factory firmware again. Quirks and known issues: - Flash layout is changed from the factory, to use both firmware image partitions for storage using mtd-concat, and uImage format is used to actually boot the system, which rules out the dual-boot capability. - The 2.4 GHz radio has its own EEPROM on board, not connected to CPU. - The stock firmware has dual-boot capability, which is not supported in OpenWrt by choice. It is controlled by data in the top 64kB of RAM which is unmapped, to avoid the interference in the boot process and accidental switch to the inactive image, although boot script presence in form of "bootcmd" variable should prevent this entirely. - On some versions of stock firmware, it is possible to obtain root shell, however not much is available in terms of debugging facitilies. 1. Login to the rkscli 2. Execute hidden command "Ruckus" 3. Copy and paste ";/bin/sh;" including quotes. This is required only once, the payload will be stored in writable filesystem. 4. Execute hidden command "!v54!". Press Enter leaving empty reply for "What's your chow?" prompt. 5. Busybox shell shall open. Source: https://alephsecurity.com/vulns/aleph-2019014 Signed-off-by: Lech Perczak <lech.perczak@gmail.com>	2022-11-13 22:36:06 +01:00
Daniel Golle	e586de8dbf	ath79: add support for Teltonika RUT300 Add support for the Teltonika RUT300 rugged industrial Ethernet router Hardware -------- SoC: Qualcomm Atheros QCA9531 RAM: 64M DDR2 (EtronTech EM68B16CWQK-25IH) FLASH: 16M SPI-NOR (Winbond W25Q128) ETH: 4x 100M LAN (QCA9533 internal AR8229 switch, eth0) 1x 100M WAN (QCA9533 internal PHY, eth1) UART: 115200 8n1, same debug port as other Teltonika devices USB: 1 single USB 2.0 host port BUTTON: Reset LED: 1x green power LED (always on) 5x yellow Ethernet port LED (controlled by Linux) WAN port LED is used as boot status and upgrade indicator as the power LED cannot be controlled in software. Use the *-factory.bin file to intially flash the device using the vendor firmware's Web-UI. Signed-off-by: Daniel Golle <daniel@makrotopia.org>	2022-11-10 21:35:34 +00:00
Korey Caro	12cee86989	ath79: add support to TrendNet TEW-673GRU Add support for the TrendNet TEW-673GRU to ath79. This device was supported in 19.07.9 but was deprecated with ar71xx. This is mostly a copy of D-Link DIR-825 B1. Updates have been completed to enable factory.bin and sysupgrade.bin both. Code improvements to DTS file and makefile. Architecture \| MIPS Vendor \| Qualcomm Atheros bootloader \| U-Boot System-On-Chip \| AR7161 rev 2 (MIPS 24Kc V7.4) CPU/Speed \| 24Kc V7.4 680 MHz Flash-Chip \| Macronix MX25L6405D Flash size \| 8192 KiB RAM Chip: \| ProMOS V58C2256164SCI5 × 2 RAM size \| 64 MiB Wireless \| 2 x Atheros AR922X 2.4GHz/5.0GHz 802.11abgn Ethernet \| RealTek RTL8366S Gigabit w/ port based vlan support USB \| Yes 2 x 2.0 Initial Flashing Process: 1) Download 22.03 tew-673gru factory bin 2) Flash 22.03 using TrendNet GUI OpenWRT Upgrade Process 3) Download 22.03 tew-673gru sysupgrade.bin 4) Flash 22.03 using OpenWRT GUI Signed-off-by: Korey Caro <korey.caro@gmail.com>	2022-11-06 00:51:58 +01:00
Edward Chow	50f727b773	ath79: add support for Linksys EA4500 v3 Add support for the Linksys EA4500 v3 wireless router Hardware -------- SoC: Qualcomm Atheros QCA9558 RAM: 128M DDR2 (Winbond W971GG6KB-25) FLASH: 128M SPI-NAND (Spansion S34ML01G100TFI00) WLAN: QCA9558 3T3R 802.11 bgn QCA9580 3T3R 802.11 an ETH: Qualcomm Atheros QCA8337 UART: 115200 8n1, same as ea4500 v2 USB: 1 single USB 2.0 host port BUTTON: Reset - WPS LED: 1x system-LED LEDs besides the ethernet ports are controlled by the ethernet switch MAC Address: use address(sample 1) source label 94:10:3e:xx:xx:6f caldata@cal_macaddr lan 94:10:3e:xx:xx:6f $label wan 94:10:3e:xx:xx:6f $label WiFi4_2G 94:10:3e:xx:xx:70 caldata@cal_ath9k_soc WiFi4_5G 94:10:3e:xx:xx:71 caldata@cal_ath9k_pci Installation from Serial Console ------------ 1. Connect to the serial console. Power up the device and interrupt autoboot when prompted 2. Connect a TFTP server reachable at 192.168.1.0/24 (e.g. 192.168.1.66) to the ethernet port. Serve the OpenWrt initramfs image as "openwrt.bin" 3. To test OpenWrt only, go to step 4 and never execute step 5; To install, auto_recovery should be disabled first, and boot_part should be set to 1 if its current value is not. ath> setenv auto_recovery no ath> setenv boot_part 1 ath> saveenv 4. Boot the initramfs image using U-Boot ath> setenv serverip 192.168.1.66 ath> tftpboot 0x84000000 openwrt.bin ath> bootm 5. Copy the OpenWrt sysupgrade image to the device using scp and install it like a normal upgrade (with no need to keeping config since no config from "previous OpenWRT installation" could be kept at all) # sysupgrade -n /path/to/openwrt/sysupgrade.bin Note: Like many other routers produced by Linksys, it has a dual firmware flash layout, but because I do not know how to handle it, I decide to disable it for more usable space. (That is why the "auto_recovery" above should be disabled before installing OpenWRT.) If someone is interested in generating factory firmware image capable to flash from stock firmware, as well as restoring the dual firmware layout, commented-out layout for the original secondary partitions left in the device tree may be a useful hint. Installation from Web Interface ------------ 1. Login to the router via its web interface (default password: admin) 2. Find the firmware update interface under "Connectivity/Basic" 3. Choose the OpenWrt factory image and click "Start" 4. If the router still boots into the stock firmware, it means that the OpenWrt factory image has been installed to the secondary partitions and failed to boot (since OpenWrt on EA4500 v3 does not support dual boot yet), and the router switched back to the stock firmware on the primary partitions. You have to install a stock firmware (e.g. 3.1.6.172023, downloadable from https://www.linksys.com/support-article?articleNum=148385 ) first (to the secondary partitions) , and after that, install OpenWrt factory image (to the primary partitions). After successful installation of OpenWrt, auto_recovery will be automatically disabled and router will only boot from the primary partitions. Signed-off-by: Edward Chow <equu@openmail.cc>	2022-10-30 23:14:45 +01:00
INAGAKI Hiroshi	2e1ffc3412	ath79: use ARTIFACTS for initramfs-factory of ELECOM devices Use ARTIFACTS to generate factory image of the following ELECOM devices instead of redundant recipe which generate on KERNEL_INITRAMFS. - ELECOM WRC-300GHBK2-I - ELECOM WRC-1750GHBK2-I/C Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>	2022-10-19 22:58:12 +02:00
Sungbo Eo	deb6f378bf	ath79: specify factory.bin recipe for ASUS RP-AC51 Currently factory.bin image recipe of ASUS RP-AC51 is not specified explicitly and is thus set to the leaked one from the device recipe right above, i.e. ASUS PL-AC56. Fix it to avoid potential breakage. Fixes: `416d4483e8` ("ath79: add support for ASUS RP-AC51") Signed-off-by: Sungbo Eo <mans0n@gorani.run>	2022-09-18 03:09:19 +09:00
Will Moss	e22ca21daa	ath79: add support for TP-Link TL-WR941ND v5 Specifications: - SoC: ar9341 - RAM: 32M - Flash: 4M - Ethernet: 5x FE ports - WiFi: ar9341-wmac Flash instruction: Upload generated factory firmware on vendor's web interface. This device is very similar to the TL-WR841N v8, only two LED GPIOs are different. Buttons configuration is similar to TL-WR842ND v2 but both buttons are active low. Signed-off-by: Will Moss <willormos@gmail.com>	2022-09-11 22:00:22 +02:00
Nick French	20581ee8b5	ath79: add support for TP-Link Deco S4 Add support for TP-Link Deco S4 wifi router The label refers to the device as S4R and the TP-Link firmware site calls it the Deco S4 v2. (There does not appear to be a v1) Hardware (and FCC id) are identical to the Deco M4R v2 but the flash layout is ordered differently and the OEM firmware encrypts some config parameters (including the label mac address) in flash In order to set the encrypted mac address, the wlan's caldata node is removed from the DTS so the mac can be decrypted with the help of the uencrypt tool and patched into the wlan fw via hotplug Specifications: SoC: QCA9563-AL3A RAM: Zentel A3R1GE40JBF Wireless 2.4GHz: QCA9563-AL3A (main SoC) Wireless 5GHz: QCA9886 Ethernet Switch: QCA8337N-AL3C Flash: 16 MB SPI NOR UART serial access (115200N1) on board via solder pads: RX = TP1 pad TX = TP2 pad GND = C201 (pad nearest board edge) The device's bootloader and web gui will only accept images that were signed using TP-Link's RSA key, however a memory safety bug in the bootloader can be leveraged to install openwrt without accessing the serial console. See developer forum S4 support page for link to a "firmware" file that starts a tftp client, or you may generate one on your own like this: ``` python - > deco_s4_faux_fw_tftp.bin <<EOF import sys from struct import pack b = pack('>I', 0x00008000) + b'X'16 + b"fw-type:" \ + b'x'256 + b"S000S001S002" + pack('>I', 0x80060200) \ b += b"\x00"(0x200-len(b)) \ + pack(">33I", [0x3c0887fc, 0x35083ddc, 0xad000000, 0x24050000, 0x3c048006, 0x348402a0, 0x3c1987f9, 0x373947f4, 0x0320f809, 0x00000000, 0x24050000, 0x3c048006, 0x348402d0, 0x3c1987f9, 0x373947f4, 0x0320f809, 0x00000000, 0x24050000, 0x3c048006, 0x34840300, 0x3c1987f9, 0x373947f4, 0x0320f809, 0x00000000, 0x24050000, 0x3c048006, 0x34840400, 0x3c1987f9, 0x373947f4, 0x0320f809, 0x00000000, 0x1000fff1, 0x00000000]) b += b"\xff"(0x2A0-len(b)) + b"setenv serverip 192.168.0.2\x00" b += b"\xff"(0x2D0-len(b)) + b"setenv ipaddr 192.168.0.1\x00" b += b"\xff"(0x300-len(b)) + b"tftpboot 0x81000000 initramfs-kernel.bin\x00" b += b"\xff"(0x400-len(b)) + b"bootm 0x81000000\x00" b += b"\xff"*(0x8000-len(b)) sys.stdout.buffer.write(b) EOF ``` Installation: 1. Run tftp server on pc with static ip 192.168.0.2 2. Place openwrt "initramfs-kernel.bin" image in tftp root dir 3. Connect pc to router ethernet port1 4. While holding in reset button on bottom of router, power on router 5. From pc access router webgui at http://192.168.0.1 6. Upload deco_s4_faux_fw_tftp.bin 7. Router will load and execture in-memory openwrt 8. Switch pc back to dhcp or static 192.168.1.x 9. Flash openwrt sysupgrade image via luci/ssh at 192.168.1.1 Revert to stock: Press and hold reset button while powering device to start the bootloader's recovery mode, where stock firmware can be uploaded via web gui at 192.168.0.1 Please note that one additional non-github commits is also needed: firmware-utils: add tplink-safeloader support for Deco S4 Signed-off-by: Nick French <nickfrench@gmail.com>	2022-09-11 21:54:00 +02:00
Michael Pratt	5df1b33298	ath79: add support for Senao Watchguard AP100 FCC ID: U2M-CAP2100AG WatchGuard AP100 is an indoor wireless access point with 1 Gb ethernet port, dual-band but single-radio wireless, internal antenna plates, and 802.3at PoE+ this board is a Senao device: the hardware is equivalent to EnGenius EAP300 v2 the software is modified Senao SDK which is based on openwrt and uboot including image checksum verification at boot time, and a failsafe image that boots if checksum fails Specification: - AR9344 SOC MIPS 74kc, 2.4 GHz AND 5 GHz WMAC, 2x2 - AR8035-A EPHY RGMII GbE with PoE+ IN - 25 MHz clock - 16 MB FLASH mx25l12805d - 2x 64 MB RAM - UART console J11, populated - GPIO watchdog GPIO 16, 20 sec toggle - 2 antennas 5 dBi, internal omni-directional plates - 5 LEDs power, eth0 link/data, 2G, 5G - 1 button reset MAC addresses: Label has no MAC Only one Vendor MAC address in flash at art 0x0 eth0 ---- :e5 art 0x0 -2 phy0 ---- :e5 art 0x0 -2 Installation: Method 1: OEM webpage use OEM webpage for firmware upgrade to upload factory.bin Method 2: root shell It may be necessary to use a Watchguard router to flash the image to the AP and / or to downgrade the software on the AP to access SSH For some Watchguard devices, serial console over UART is disabled. NOTE: DHCP is not enabled by default after flashing TFTP recovery: reset button has no function at boot time only possible with modified uboot environment, (see commit message for Watchguard AP300) Return to OEM: user should make backup of MTD partitions and write the backups back to mtd devices in order to revert to OEM reliably It may be possible to use sysupgrade with an OEM image as well... (not tested) OEM upgrade info: The OEM upgrade script is at /etc/fwupgrade.sh OKLI kernel loader is required because the OEM software expects the kernel to be no greater than 1536k and the factory.bin upgrade procedure would otherwise overwrite part of the kernel when writing rootfs. Note on eth0 PLL-data: The default Ethernet Configuration register values will not work because of the external AR8035 switch between the SOC and the ethernet port. For AR934x series, the PLL registers for eth0 can be see in the DTSI as 0x2c. Therefore the PLL registers can be read from uboot for each link speed after attempting tftpboot or another network action using that link speed with `md 0x1805002c 1`. The clock delay required for RGMII can be applied at the PHY side, using the at803x driver `phy-mode`. Therefore the PLL registers for GMAC0 do not need the bits for delay on the MAC side. This is possible due to fixes in at803x driver since Linux 5.1 and 5.3 Note on WatchGuard Magic string: The OEM upgrade script is a modified version of the generic Senao sysupgrade script which is used on EnGenius devices. On WatchGuard boards produced by Senao, images are verified using a md5sum checksum of the upgrade image concatenated with a magic string. this checksum is then appended to the end of the final image. This variable does not apply to all the senao devices so set to null string as default Tested-by: Steve Wheeler <stephenw10@gmail.com> Signed-off-by: Michael Pratt <mcpratt@pm.me>	2022-09-11 21:54:00 +02:00
Michael Pratt	9f6e247854	ath79: add support for Senao WatchGuard AP200 FCC ID: U2M-CAP4200AG WatchGuard AP200 is an indoor wireless access point with 1 Gb ethernet port, dual-band wireless, internal antenna plates, and 802.3at PoE+ this board is a Senao device: the hardware is equivalent to EnGenius EAP600 the software is modified Senao SDK which is based on openwrt and uboot including image checksum verification at boot time, and a failsafe image that boots if checksum fails Specification: - AR9344 SOC MIPS 74kc, 2.4 GHz WMAC, 2x2 - AR9382 WLAN PCI card 168c:0030, 5 GHz, 2x2, 26dBm - AR8035-A EPHY RGMII GbE with PoE+ IN - 25 MHz clock - 16 MB FLASH mx25l12805d - 2x 64 MB RAM - UART console J11, populated - GPIO watchdog GPIO 16, 20 sec toggle - 4 antennas 5 dBi, internal omni-directional plates - 5 LEDs power, eth0 link/data, 2G, 5G - 1 button reset MAC addresses: Label has no MAC Only one Vendor MAC address in flash at art 0x0 eth0 ---- :be art 0x0 -2 phy1 ---- :bf art 0x0 -1 phy0 ---- :be art 0x0 -2 Installation:* Method 1: OEM webpage use OEM webpage for firmware upgrade to upload factory.bin Method 2: root shell It may be necessary to use a Watchguard router to flash the image to the AP and / or to downgrade the software on the AP to access SSH For some Watchguard devices, serial console over UART is disabled. NOTE: DHCP is not enabled by default after flashing TFTP recovery: reset button has no function at boot time only possible with modified uboot environment, (see commit message for Watchguard AP300) Return to OEM: user should make backup of MTD partitions and write the backups back to mtd devices in order to revert to OEM reliably It may be possible to use sysupgrade with an OEM image as well... (not tested) OEM upgrade info: The OEM upgrade script is at /etc/fwupgrade.sh OKLI kernel loader is required because the OEM software expects the kernel to be no greater than 1536k and the factory.bin upgrade procedure would otherwise overwrite part of the kernel when writing rootfs. Note on eth0 PLL-data: The default Ethernet Configuration register values will not work because of the external AR8035 switch between the SOC and the ethernet port. For AR934x series, the PLL registers for eth0 can be see in the DTSI as 0x2c. Therefore the PLL registers can be read from uboot for each link speed after attempting tftpboot or another network action using that link speed with `md 0x1805002c 1`. The clock delay required for RGMII can be applied at the PHY side, using the at803x driver `phy-mode`. Therefore the PLL registers for GMAC0 do not need the bits for delay on the MAC side. This is possible due to fixes in at803x driver since Linux 5.1 and 5.3 Note on WatchGuard Magic string: The OEM upgrade script is a modified version of the generic Senao sysupgrade script which is used on EnGenius devices. On WatchGuard boards produced by Senao, images are verified using a md5sum checksum of the upgrade image concatenated with a magic string. this checksum is then appended to the end of the final image. This variable does not apply to all the senao devices so set to null string as default Tested-by: Steve Wheeler <stephenw10@gmail.com> Tested-by: John Delaney <johnd@ankco.net> Signed-off-by: Michael Pratt <mcpratt@pm.me>	2022-09-11 21:54:00 +02:00
Michael Pratt	146aaeafb7	ath79: add support for Senao WatchGuard AP300 FCC ID: Q6G-AP300 WatchGuard AP300 is an indoor wireless access point with 1 Gb ethernet port, dual-band wireless, internal antenna plates, and 802.3at PoE+ this board is a Senao device: the hardware is equivalent to EnGenius EAP1750 the software is modified Senao SDK which is based on openwrt and uboot including image checksum verification at boot time, and a failsafe image that boots if checksum fails Specification: - QCA9558 SOC MIPS 74kc, 2.4 GHz WMAC, 3x3 - QCA9880 WLAN PCI card 168c:003c, 5 GHz, 3x3, 26dBm - AR8035-A PHY RGMII GbE with PoE+ IN - 40 MHz clock - 32 MB FLASH S25FL512S - 2x 64 MB RAM NT5TU32M16 - UART console J10, populated - GPIO watchdog GPIO 16, 20 sec toggle - 6 antennas 5 dBi, internal omni-directional plates - 5 LEDs power, eth0 link/data, 2G, 5G - 1 button reset MAC addresses: MAC address labeled as ETH Only one Vendor MAC address in flash at art 0x0 eth0 ETH :3c art 0x0 phy1 ---- :3d --- phy0 ---- :3e --- Serial console access:* For this board, its not certain whether UART is possible it is likely that software is blocking console access the RX line on the board for UART is shorted to ground by resistor R176 the resistors R175 and R176 are next to the UART RX pin at J10 however console output is garbage even after this fix Installation: Method 1: OEM webpage use OEM webpage for firmware upgrade to upload factory.bin Method 2: root shell access downgrade XTM firewall to v2.0.0.1 downgrade AP300 firmware: v1.0.1 remove / unpair AP from controller perform factory reset with reset button connect ethernet to a computer login to OEM webpage with default address / pass: wgwap enable SSHD in OEM webpage settings access root shell with SSH as user 'root' modify uboot environment to automatically try TFTP at boot time (see command below) rename initramfs-kernel.bin to test.bin load test.bin over TFTP (see TFTP recovery) (optionally backup all mtdblocks to have flash backup) perform a sysupgrade with sysupgrade.bin NOTE: DHCP is not enabled by default after flashing TFTP recovery: server ip: 192.168.1.101 reset button seems to do nothing at boot time... only possible with modified uboot environment, running this command in the root shell: fw_setenv bootcmd 'if ping 192.168.1.101; then tftp 0x82000000 test.bin && bootm 0x82000000; else bootm 0x9f0a0000; fi' and verify that it is correct with fw_printenv then, before boot, the device will attempt TFTP from 192.168.1.101 looking for file 'test.bin' to return uboot environment to normal: fw_setenv bootcmd 'bootm 0x9f0a0000' Return to OEM: user should make backup of MTD partitions and write the backups back to mtd devices in order to revert to OEM (see installation method 2) It may be possible to use sysupgrade with an OEM image as well... (not tested) OEM upgrade info: The OEM upgrade script is at /etc/fwupgrade.sh OKLI kernel loader is required because the OEM software expects the kernel to be no greater than 1536k and the factory.bin upgrade procedure would otherwise overwrite part of the kernel when writing rootfs. Note on eth0 PLL-data: The default Ethernet Configuration register values will not work because of the external AR8035 switch between the SOC and the ethernet port. For QCA955x series, the PLL registers for eth0 and eth1 can be see in the DTSI as 0x28 and 0x48 respectively. Therefore the PLL registers can be read from uboot for each link speed after attempting tftpboot or another network action using that link speed with `md 0x18050028 1` and `md 0x18050048 1`. The clock delay required for RGMII can be applied at the PHY side, using the at803x driver `phy-mode`. Therefore the PLL registers for GMAC0 do not need the bits for delay on the MAC side. This is possible due to fixes in at803x driver since Linux 5.1 and 5.3 Note on WatchGuard Magic string: The OEM upgrade script is a modified version of the generic Senao sysupgrade script which is used on EnGenius devices. On WatchGuard boards produced by Senao, images are verified using a md5sum checksum of the upgrade image concatenated with a magic string. this checksum is then appended to the end of the final image. This variable does not apply to all the senao devices so set to null string as default Tested-by: Alessandro Kornowski <ak@wski.org> Tested-by: John Wagner <john@wagner.us.org> Signed-off-by: Michael Pratt <mcpratt@pm.me>	2022-09-11 21:54:00 +02:00
Lech Perczak	f1d112ee5a	ath79: support Ruckus ZoneFlex 7321 Ruckus ZoneFlex 7321 is a dual-band, single radio 802.11n 2x2 MIMO enterprise access point. It is very similar to its bigger brother, ZoneFlex 7372. Hardware highligts: - CPU: Atheros AR9342 SoC at 533 MHz - RAM: 64MB DDR2 - Flash: 32MB SPI-NOR - Wi-Fi: AR9342 built-in dual-band 2x2 MIMO radio - Ethernet: single Gigabit Ethernet port through AR8035 gigabit PHY - PoE: input through Gigabit port - Standalone 12V/1A power input - USB: optional single USB 2.0 host port on the 7321-U variant. Serial console: 115200-8-N-1 on internal H1 header. Pinout: H1 ---------- \|1\|x3\|4\|5\| ---------- Pin 1 is near the "H1" marking. 1 - RX x - no pin 3 - VCC (3.3V) 4 - GND 5 - TX JTAG: Connector H5, unpopulated, similar to MIPS eJTAG, standard, but without the key in pin 12 and not every pin routed: ------- H5 \|1 \|2 \| ------- \|3 \|4 \| ------- \|5 \|6 \| ------- \|7 \|8 \| ------- \|9 \|10\| ------- \|11\|12\| ------- \|13\|14\| ------- 3 - TDI 5 - TDO 7 - TMS 9 - TCK 2,4,6,8,10 - GND 14 - Vref 1,11,12,13 - Not connected Installation: There are two methods of installation: - Using serial console [1] - requires some disassembly, 3.3V USB-Serial adapter, TFTP server, and removing a single T10 screw, but with much less manual steps, and is generally recommended, being safer. - Using stock firmware root shell exploit, SSH and TFTP [2]. Does not work on some rare versions of stock firmware. A more involved, and requires installing `mkenvimage` from u-boot-tools package if you choose to rebuild your own environment, but can be used without disassembly or removal from installation point, if you have the credentials. If for some reason, size of your sysupgrade image exceeds 13312kB, proceed with method [1]. For official images this is not likely to happen ever. [1] Using serial console: 0. Connect serial console to H1 header. Ensure the serial converter does not back-power the board, otherwise it will fail to boot. 1. Power-on the board. Then quickly connect serial converter to PC and hit Ctrl+C in the terminal to break boot sequence. If you're lucky, you'll enter U-boot shell. Then skip to point 3. Connection parameters are 115200-8-N-1. 2. Allow the board to boot. Press the reset button, so the board reboots into U-boot again and go back to point 1. 3. Set the "bootcmd" variable to disable the dual-boot feature of the system and ensure that uImage is loaded. This is critical step, and needs to be done only on initial installation. > setenv bootcmd "bootm 0x9f040000" > saveenv 4. Boot the OpenWrt initramfs using TFTP. Replace IP addresses as needed: > setenv serverip 192.168.1.2 > setenv ipaddr 192.168.1.1 > tftpboot 0x81000000 openwrt-ath79-generic-ruckus_zf7321-initramfs-kernel.bin > bootm 0x81000000 5. Optional, but highly recommended: back up contents of "firmware" partition: $ ssh root@192.168.1.1 cat /dev/mtd1 > ruckus_zf7321_fw1_backup.bin $ ssh root@192.168.1.1 cat /dev/mtd5 > ruckus_zf7321_fw2_backup.bin 6. Copy over sysupgrade image, and perform actual installation. OpenWrt shall boot from flash afterwards: $ ssh root@192.168.1.1 # sysupgrade -n openwrt-ath79-generic-ruckus_zf7321-squashfs-sysupgrade.bin [2] Using stock root shell: 0. Reset the device to factory defaullts. Power-on the device and after it boots, hold the reset button near Ethernet connectors for 5 seconds. 1. Connect the device to the network. It will acquire address over DHCP, so either find its address using list of DHCP leases by looking for label MAC address, or try finding it by scanning for SSH port: $ nmap 10.42.0.0/24 -p22 From now on, we assume your computer has address 10.42.0.1 and the device has address 10.42.0.254. 2. Set up a TFTP server on your computer. We assume that TFTP server root is at /srv/tftp. 3. Obtain root shell. Connect to the device over SSH. The SSHD ond the frmware is pretty ancient and requires enabling HMAC-MD5. $ ssh 10.42.0.254 \ -o UserKnownHostsFile=/dev/null \ -o StrictHostKeyCheking=no \ -o MACs=hmac-md5 Login. User is "super", password is "sp-admin". Now execute a hidden command: Ruckus It is case-sensitive. Copy and paste the following string, including quotes. There will be no output on the console for that. ";/bin/sh;" Hit "enter". The AP will respond with: grrrr OK Now execute another hidden command: !v54! At "What's your chow?" prompt just hit "enter". Congratulations, you should now be dropped to Busybox shell with root permissions. 4. Optional, but highly recommended: backup the flash contents before installation. At your PC ensure the device can write the firmware over TFTP: $ sudo touch /srv/tftp/ruckus_zf7321_firmware{1,2}.bin $ sudo chmod 666 /srv/tftp/ruckus_zf7321_firmware{1,2}.bin Locate partitions for primary and secondary firmware image. NEVER blindly copy over MTD nodes, because MTD indices change depending on the currently active firmware, and all partitions are writable! # grep rcks_wlan /proc/mtd Copy over both images using TFTP, this will be useful in case you'd like to return to stock FW in future. Make sure to backup both, as OpenWrt uses bot firmwre partitions for storage! # tftp -l /dev/<rcks_wlan.main_mtd> -r ruckus_zf7321_firmware1.bin -p 10.42.0.1 # tftp -l /dev/<rcks_wlan.bkup_mtd> -r ruckus_zf7321_firmware2.bin -p 10.42.0.1 When the command finishes, copy over the dump to a safe place for storage. $ cp /srv/tftp/ruckus_zf7321_firmware{1,2}.bin ~/ 5. Ensure the system is running from the BACKUP image, i.e. from rcks_wlan.bkup partition or "image 2". Otherwise the installation WILL fail, and you will need to access mtd0 device to write image which risks overwriting the bootloader, and so is not covered here and not supported. Switching to backup firmware can be achieved by executing a few consecutive reboots of the device, or by updating the stock firmware. The system will boot from the image it was not running from previously. Stock firmware available to update was conveniently dumped in point 4 :-) 6. Prepare U-boot environment image. Install u-boot-tools package. Alternatively, if you build your own images, OpenWrt provides mkenvimage in host staging directory as well. It is recommended to extract environment from the device, and modify it, rather then relying on defaults: $ sudo touch /srv/tftp/u-boot-env.bin $ sudo chmod 666 /srv/tftp/u-boot-env.bin On the device, find the MTD partition on which environment resides. Beware, it may change depending on currently active firmware image! # grep u-boot-env /proc/mtd Now, copy over the partition # tftp -l /dev/mtd<N> -r u-boot-env.bin -p 10.42.0.1 Store the stock environment in a safe place: $ cp /srv/tftp/u-boot-env.bin ~/ Extract the values from the dump: $ strings u-boot-env.bin \| tee u-boot-env.txt Now clean up the debris at the end of output, you should end up with each variable defined once. After that, set the bootcmd variable like this: bootcmd=bootm 0x9f040000 You should end up with something like this: bootcmd=bootm 0x9f040000 bootargs=console=ttyS0,115200 rootfstype=squashfs init=/sbin/init baudrate=115200 ethaddr=0x00:0xaa:0xbb:0xcc:0xdd:0xee mtdparts=mtdparts=ar7100-nor0:256k(u-boot),13312k(rcks_wlan.main),2048k(datafs),256k(u-boot-env),512k(Board Data),13312k(rcks_wlan.bkup) mtdids=nor0=ar7100-nor0 bootdelay=2 ethact=eth0 filesize=78a000 fileaddr=81000000 partition=nor0,0 mtddevnum=0 mtddevname=u-boot ipaddr=10.0.0.1 serverip=10.0.0.5 stdin=serial stdout=serial stderr=serial These are the defaults, you can use most likely just this as input to mkenvimage. Now, create environment image and copy it over to TFTP root: $ mkenvimage -s 0x40000 -b -o u-boot-env.bin u-boot-env.txt $ sudo cp u-boot-env.bin /srv/tftp This is the same image, gzipped and base64-encoded: H4sIAAAAAAAAA+3QQW7TQBQAUF8EKRtQI6XtJDS0VJoN4gYcAE3iCbWS2MF2Sss1ORDYqVq6YMEB3rP0 Z/7Yf+aP3/56827VNP16X8Zx3E/Cw8dNuAqDYlxI7bcurpu6a3Y59v3jlzCbz5eLECbt8HbT9Y+HHLvv x9TdbbpJVVd9vOxWVX05TotVOpZt6nN8qilyf5fKso3hIYTb8JDSEFarIazXQyjLIeRc7PvykNq+iy+T 1F7PQzivmzbcLpYftmfH87G56Wz+/v18sT1r19vu649dqi/2qaqns0W4utmelalPm27I/lac5/p+OluO NZ+a1JaTz8M3/9hmtT0epmMjVdnF8djXLZx+TJl36TEuTlda93EYQrGpdrmrfuZ4fZPGHzjmp/vezMNJ MV6n6qumPm06C+MRZb6vj/v4Mk/7HJ+6LarDqXweLsZnXnS5vc9tdXheWRbd0GIdh/Uq7cakOfavsty2 z1nxGwAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAD+1x9eTkHLAAAEAA== 7. Perform actual installation. Copy over OpenWrt sysupgrade image to TFTP root: $ sudo cp openwrt-ath79-generic-ruckus_zf7321-squashfs-sysupgrade.bin /srv/tftp Now load both to the device over TFTP: # tftp -l /tmp/u-boot-env.bin -r u-boot-env.bin -g 10.42.0.1 # tftp -l /tmp/openwrt.bin -r openwrt-ath79-generic-ruckus_zf7321-squashfs-sysupgrade.bin -g 10.42.0.1 Vverify checksums of both images to ensure the transfer over TFTP was completed: # sha256sum /tmp/u-boot-env.bin /tmp/openwrt.bin And compare it against source images: $ sha256sum /srv/tftp/u-boot-env.bin /srv/tftp/openwrt-ath79-generic-ruckus_zf7321-squashfs-sysupgrade.bin Locate MTD partition of the primary image: # grep rcks_wlan.main /proc/mtd Now, write the images in place. Write U-boot environment last, so unit still can boot from backup image, should power failure occur during this. Replace MTD placeholders with real MTD nodes: # flashcp /tmp/openwrt.bin /dev/<rcks_wlan.main_mtd> # flashcp /tmp/u-boot-env.bin /dev/<u-boot-env_mtd> Finally, reboot the device. The device should directly boot into OpenWrt. Look for the characteristic power LED blinking pattern. # reboot -f After unit boots, it should be available at the usual 192.168.1.1/24. Return to factory firmware: 1. Boot into OpenWrt initramfs as for initial installation. To do that without disassembly, you can write an initramfs image to the device using 'sysupgrade -F' first. 2. Unset the "bootcmd" variable: fw_setenv bootcmd "" 3. Write factory images downloaded from manufacturer website into fwconcat0 and fwconcat1 MTD partitions, or restore backup you took before installation: mtd write ruckus_zf7321_fw1_backup.bin /dev/mtd1 mtd write ruckus_zf7321_fw2_backup.bin /dev/mtd5 4. Reboot the system, it should load into factory firmware again. Quirks and known issues: - Flash layout is changed from the factory, to use both firmware image partitions for storage using mtd-concat, and uImage format is used to actually boot the system, which rules out the dual-boot capability. - The 5GHz radio has its own EEPROM on board, not connected to CPU. - The stock firmware has dual-boot capability, which is not supported in OpenWrt by choice. It is controlled by data in the top 64kB of RAM which is unmapped, to avoid the interference in the boot process and accidental switch to the inactive image, although boot script presence in form of "bootcmd" variable should prevent this entirely. - U-boot disables JTAG when starting. To re-enable it, you need to execute the following command before booting: mw.l 1804006c 40 And also you need to disable the reset button in device tree if you intend to debug Linux, because reset button on GPIO0 shares the TCK pin. - On some versions of stock firmware, it is possible to obtain root shell, however not much is available in terms of debugging facitilies. 1. Login to the rkscli 2. Execute hidden command "Ruckus" 3. Copy and paste ";/bin/sh;" including quotes. This is required only once, the payload will be stored in writable filesystem. 4. Execute hidden command "!v54!". Press Enter leaving empty reply for "What's your chow?" prompt. 5. Busybox shell shall open. Source: https://alephsecurity.com/vulns/aleph-2019014 Signed-off-by: Lech Perczak <lech.perczak@gmail.com>	2022-09-11 01:36:25 +02:00
Lech Perczak	59cb4dc91d	ath79: support Ruckus ZoneFlex 7372 Ruckus ZoneFlex 7372 is a dual-band, dual-radio 802.11n 2x2 MIMO enterprise access point. Ruckus ZoneFlex 7352 is also supported, lacking the 5GHz radio part. Hardware highligts: - CPU: Atheros AR9344 SoC at 560 MHz - RAM: 128MB DDR2 - Flash: 32MB SPI-NOR - Wi-Fi 2.4GHz: AR9344 built-in 2x2 MIMO radio - Wi-Fi 5Ghz: AR9582 2x2 MIMO radio (Only in ZF7372) - Antennas: - Separate internal active antennas with beamforming support on both bands with 7 elements per band, each controlled by 74LV164 GPIO expanders, attached to GPIOs of each radio. - Two dual-band external RP-SMA antenna connections on "7372-E" variant. - Ethernet 1: single Gigabit Ethernet port through AR8035 gigabit PHY - Ethernet 2: single Fast Ethernet port through AR9344 built-in switch - PoE: input through Gigabit port - Standalone 12V/1A power input - USB: optional single USB 2.0 host port on "-U" variants. The same image should support: - ZoneFlex 7372E (variant with external antennas, without beamforming capability) - ZoneFlex 7352 (single-band, 2.4GHz-only variant). which are based on same baseboard (codename St. Bernard), with different populated components. Serial console: 115200-8-N-1 on internal H1 header. Pinout: H1 --- \|5\| --- \|4\| --- \|3\| --- \|x\| --- \|1\| --- Pin 5 is near the "H1" marking. 1 - RX x - no pin 3 - VCC (3.3V) 4 - GND 5 - TX JTAG: Connector H2, similar to MIPS eJTAG, standard, but without the key in pin 12 and not every pin routed: ------- H2 \|1 \|2 \| ------- \|3 \|4 \| ------- \|5 \|6 \| ------- \|7 \|8 \| ------- \|9 \|10\| ------- \|11\|12\| ------- \|13\|14\| ------- 3 - TDI 5 - TDO 7 - TMS 9 - TCK 2,4,6,8,10 - GND 14 - Vref 1,11,12,13 - Not connected Installation: There are two methods of installation: - Using serial console [1] - requires some disassembly, 3.3V USB-Serial adapter, TFTP server, and removing a single T10 screw, but with much less manual steps, and is generally recommended, being safer. - Using stock firmware root shell exploit, SSH and TFTP [2]. Does not work on some rare versions of stock firmware. A more involved, and requires installing `mkenvimage` from u-boot-tools package if you choose to rebuild your own environment, but can be used without disassembly or removal from installation point, if you have the credentials. If for some reason, size of your sysupgrade image exceeds 13312kB, proceed with method [1]. For official images this is not likely to happen ever. [1] Using serial console: 0. Connect serial console to H1 header. Ensure the serial converter does not back-power the board, otherwise it will fail to boot. 1. Power-on the board. Then quickly connect serial converter to PC and hit Ctrl+C in the terminal to break boot sequence. If you're lucky, you'll enter U-boot shell. Then skip to point 3. Connection parameters are 115200-8-N-1. 2. Allow the board to boot. Press the reset button, so the board reboots into U-boot again and go back to point 1. 3. Set the "bootcmd" variable to disable the dual-boot feature of the system and ensure that uImage is loaded. This is critical step, and needs to be done only on initial installation. > setenv bootcmd "bootm 0x9f040000" > saveenv 4. Boot the OpenWrt initramfs using TFTP. Replace IP addresses as needed: > setenv serverip 192.168.1.2 > setenv ipaddr 192.168.1.1 > tftpboot 0x81000000 openwrt-ath79-generic-ruckus_zf7372-initramfs-kernel.bin > bootm 0x81000000 5. Optional, but highly recommended: back up contents of "firmware" partition: $ ssh root@192.168.1.1 cat /dev/mtd1 > ruckus_zf7372_fw1_backup.bin $ ssh root@192.168.1.1 cat /dev/mtd5 > ruckus_zf7372_fw2_backup.bin 6. Copy over sysupgrade image, and perform actual installation. OpenWrt shall boot from flash afterwards: $ ssh root@192.168.1.1 # sysupgrade -n openwrt-ath79-generic-ruckus_zf7372-squashfs-sysupgrade.bin [2] Using stock root shell: 0. Reset the device to factory defaullts. Power-on the device and after it boots, hold the reset button near Ethernet connectors for 5 seconds. 1. Connect the device to the network. It will acquire address over DHCP, so either find its address using list of DHCP leases by looking for label MAC address, or try finding it by scanning for SSH port: $ nmap 10.42.0.0/24 -p22 From now on, we assume your computer has address 10.42.0.1 and the device has address 10.42.0.254. 2. Set up a TFTP server on your computer. We assume that TFTP server root is at /srv/tftp. 3. Obtain root shell. Connect to the device over SSH. The SSHD ond the frmware is pretty ancient and requires enabling HMAC-MD5. $ ssh 10.42.0.254 \ -o UserKnownHostsFile=/dev/null \ -o StrictHostKeyCheking=no \ -o MACs=hmac-md5 Login. User is "super", password is "sp-admin". Now execute a hidden command: Ruckus It is case-sensitive. Copy and paste the following string, including quotes. There will be no output on the console for that. ";/bin/sh;" Hit "enter". The AP will respond with: grrrr OK Now execute another hidden command: !v54! At "What's your chow?" prompt just hit "enter". Congratulations, you should now be dropped to Busybox shell with root permissions. 4. Optional, but highly recommended: backup the flash contents before installation. At your PC ensure the device can write the firmware over TFTP: $ sudo touch /srv/tftp/ruckus_zf7372_firmware{1,2}.bin $ sudo chmod 666 /srv/tftp/ruckus_zf7372_firmware{1,2}.bin Locate partitions for primary and secondary firmware image. NEVER blindly copy over MTD nodes, because MTD indices change depending on the currently active firmware, and all partitions are writable! # grep rcks_wlan /proc/mtd Copy over both images using TFTP, this will be useful in case you'd like to return to stock FW in future. Make sure to backup both, as OpenWrt uses bot firmwre partitions for storage! # tftp -l /dev/<rcks_wlan.main_mtd> -r ruckus_zf7372_firmware1.bin -p 10.42.0.1 # tftp -l /dev/<rcks_wlan.bkup_mtd> -r ruckus_zf7372_firmware2.bin -p 10.42.0.1 When the command finishes, copy over the dump to a safe place for storage. $ cp /srv/tftp/ruckus_zf7372_firmware{1,2}.bin ~/ 5. Ensure the system is running from the BACKUP image, i.e. from rcks_wlan.bkup partition or "image 2". Otherwise the installation WILL fail, and you will need to access mtd0 device to write image which risks overwriting the bootloader, and so is not covered here and not supported. Switching to backup firmware can be achieved by executing a few consecutive reboots of the device, or by updating the stock firmware. The system will boot from the image it was not running from previously. Stock firmware available to update was conveniently dumped in point 4 :-) 6. Prepare U-boot environment image. Install u-boot-tools package. Alternatively, if you build your own images, OpenWrt provides mkenvimage in host staging directory as well. It is recommended to extract environment from the device, and modify it, rather then relying on defaults: $ sudo touch /srv/tftp/u-boot-env.bin $ sudo chmod 666 /srv/tftp/u-boot-env.bin On the device, find the MTD partition on which environment resides. Beware, it may change depending on currently active firmware image! # grep u-boot-env /proc/mtd Now, copy over the partition # tftp -l /dev/mtd<N> -r u-boot-env.bin -p 10.42.0.1 Store the stock environment in a safe place: $ cp /srv/tftp/u-boot-env.bin ~/ Extract the values from the dump: $ strings u-boot-env.bin \| tee u-boot-env.txt Now clean up the debris at the end of output, you should end up with each variable defined once. After that, set the bootcmd variable like this: bootcmd=bootm 0x9f040000 You should end up with something like this: bootcmd=bootm 0x9f040000 bootargs=console=ttyS0,115200 rootfstype=squashfs init=/sbin/init baudrate=115200 ethaddr=0x00:0xaa:0xbb:0xcc:0xdd:0xee bootdelay=2 mtdids=nor0=ar7100-nor0 mtdparts=mtdparts=ar7100-nor0:256k(u-boot),13312k(rcks_wlan.main),2048k(datafs),256k(u-boot-env),512k(Board Data),13312k(rcks_wlan.bkup) ethact=eth0 filesize=1000000 fileaddr=81000000 ipaddr=192.168.0.7 serverip=192.168.0.51 partition=nor0,0 mtddevnum=0 mtddevname=u-boot stdin=serial stdout=serial stderr=serial These are the defaults, you can use most likely just this as input to mkenvimage. Now, create environment image and copy it over to TFTP root: $ mkenvimage -s 0x40000 -b -o u-boot-env.bin u-boot-env.txt $ sudo cp u-boot-env.bin /srv/tftp This is the same image, gzipped and base64-encoded: H4sIAAAAAAAAA+3QTW7TQBQAYB+AQ2TZSGk6Tpv+SbNBrNhyADSJHWolsYPtlJaDcAWOCXaqQhdIXOD7 Fm/ee+MZ+/nHu58fV03Tr/dFHNf9JDzdbcJVGGRjI7Vfurhu6q7ZlbHvnz+FWZ4vFyFM2mF30/XPhzJ2 X4+pe9h0k6qu+njRrar6YkyzVToWberL+HImK/uHVBRtDE8h3IenlIawWg1hvR5CUQyhLE/vLcpdeo6L bN8XVdHFumlDTO1NHsL5mI/9Q2r7Lv5J3uzeL5bX27Pj+XjRdJZfXuaL7Vm73nafv+1SPd+nqp7OFuHq dntWpD5tuqH6e+K8rB+ns+V45n2T2mLyYXjmH9estsfD9DTSuo/DErJNtSu76vswbjg5NU4D3752qsOp zu8W8/z6dh7mN1lXto9lWx3eNJd5Ng5V9VVTn2afnSYuysf6uI9/8rQv48s3Z93wn+o4XFWl3Vg0x/5N Vbbta5X9AgAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAID/+Q2Z/B7cAAAEAA== 7. Perform actual installation. Copy over OpenWrt sysupgrade image to TFTP root: $ sudo cp openwrt-ath79-generic-ruckus_zf7372-squashfs-sysupgrade.bin /srv/tftp Now load both to the device over TFTP: # tftp -l /tmp/u-boot-env.bin -r u-boot-env.bin -g 10.42.0.1 # tftp -l /tmp/openwrt.bin -r openwrt-ath79-generic-ruckus_zf7372-squashfs-sysupgrade.bin -g 10.42.0.1 Verify checksums of both images to ensure the transfer over TFTP was completed: # sha256sum /tmp/u-boot-env.bin /tmp/openwrt.bin And compare it against source images: $ sha256sum /srv/tftp/u-boot-env.bin /srv/tftp/openwrt-ath79-generic-ruckus_zf7372-squashfs-sysupgrade.bin Locate MTD partition of the primary image: # grep rcks_wlan.main /proc/mtd Now, write the images in place. Write U-boot environment last, so unit still can boot from backup image, should power failure occur during this. Replace MTD placeholders with real MTD nodes: # flashcp /tmp/openwrt.bin /dev/<rcks_wlan.main_mtd> # flashcp /tmp/u-boot-env.bin /dev/<u-boot-env_mtd> Finally, reboot the device. The device should directly boot into OpenWrt. Look for the characteristic power LED blinking pattern. # reboot -f After unit boots, it should be available at the usual 192.168.1.1/24. Return to factory firmware: 1. Boot into OpenWrt initramfs as for initial installation. To do that without disassembly, you can write an initramfs image to the device using 'sysupgrade -F' first. 2. Unset the "bootcmd" variable: fw_setenv bootcmd "" 3. Write factory images downloaded from manufacturer website into fwconcat0 and fwconcat1 MTD partitions, or restore backup you took before installation: mtd write ruckus_zf7372_fw1_backup.bin /dev/mtd1 mtd write ruckus_zf7372_fw2_backup.bin /dev/mtd5 4. Reboot the system, it should load into factory firmware again. Quirks and known issues: - This is first device in ath79 target to support link state reporting on FE port attached trough the built-in switch. - Flash layout is changed from the factory, to use both firmware image partitions for storage using mtd-concat, and uImage format is used to actually boot the system, which rules out the dual-boot capability. The 5GHz radio has its own EEPROM on board, not connected to CPU. - The stock firmware has dual-boot capability, which is not supported in OpenWrt by choice. It is controlled by data in the top 64kB of RAM which is unmapped, to avoid the interference in the boot process and accidental switch to the inactive image, although boot script presence in form of "bootcmd" variable should prevent this entirely. - U-boot disables JTAG when starting. To re-enable it, you need to execute the following command before booting: mw.l 1804006c 40 And also you need to disable the reset button in device tree if you intend to debug Linux, because reset button on GPIO0 shares the TCK pin. - On some versions of stock firmware, it is possible to obtain root shell, however not much is available in terms of debugging facitilies. 1. Login to the rkscli 2. Execute hidden command "Ruckus" 3. Copy and paste ";/bin/sh;" including quotes. This is required only once, the payload will be stored in writable filesystem. 4. Execute hidden command "!v54!". Press Enter leaving empty reply for "What's your chow?" prompt. 5. Busybox shell shall open. Source: https://alephsecurity.com/vulns/aleph-2019014 - Stock firmware has beamforming functionality, known as BeamFlex, using active multi-segment antennas on both bands - controlled by RF analog switches, driven by a pair of 74LV164 shift registers. Shift registers used for each radio are connected to GPIO14 (clock) and GPIO15 of the respective chip. They are mapped as generic GPIOs in OpenWrt - in stock firmware, they were most likely handled directly by radio firmware, given the real-time nature of their control. Lack of this support in OpenWrt causes the antennas to behave as ordinary omnidirectional antennas, and does not affect throughput in normal conditions, but GPIOs are available to tinker with nonetheless. Signed-off-by: Lech Perczak <lech.perczak@gmail.com>	2022-09-11 01:36:25 +02:00
John Thomson	62b72eafe4	ath79: mikrotik: use OpenWrt loader for initram image Return to using the OpenWrt kernel loader to decompress and load kernel initram image. Continue to use the vmlinuz kernel for squashfs. Mikrotik's bootloader RouterBOOT on some ath79 devices is failing to boot the current initram, due to the size of the initram image. On the ath79 wAP-ac: a 5.7MiB initram image would fail to boot After this change: a 6.6MiB initram image successfully loads This partially reverts commit `e91344776b`. An alternative of using RouterBOOT's capability of loading an initrd ELF section was investigated, but the OpenWrt kernel loader allows larger image. Signed-off-by: John Thomson <git@johnthomson.fastmail.com.au>	2022-09-11 01:30:11 +02:00
David Bauer	1e1695f959	ath79: add support for ZTE MF281 Add support for the ZTE MF281 battery-powered WiFi router. Hardware -------- SoC: Qualcomm Atheros QCA9563 RAM: 128M DDR2 FLASH: 2M SPI-NOR (GigaDevice GD25Q16) 128M SPI-NAND (GigaDevice) WLAN: QCA9563 2T2R 802.11 abgn QCA9886 2T2R 802.11 nac WWAN: ASRMicro ASR1826 ETH: Qualcomm Atheros QCA8337 UART: 115200 8n1 Unpopulated connector next to SIM slot (SIM) GND - RX - TX - 3V3 Don't connect 3V3 BUTTON: Reset - WPS LED: 1x debug-LED (internal) LEDs on front of the device are controlled using the modem CPU and can not be controlled by OpenWrt Installation ------------ 1. Connect to the serial console. Power up the device and interrupt autoboot when prompted 2. Connect a TFTP server reachable at 192.168.1.66 to the ethernet port. Serve the OpenWrt initramfs image as "speedbox-2.bin" 3. Boot the initramfs image using U-Boot $ setenv serverip 192.168.1.66 $ setenv ipaddr 192.168.1.154 $ tftpboot 0x84000000 speedbox-2.bin $ bootm 4. Copy the OpenWrt factory image to the device using scp and write to the NAND flash $ mtd write /path/to/openwrt/factory.bin firmware WWAN ---- The WWAN card can be used with OpenWrt. Example configuration for connection with a unauthenticated dual-stack APN: network.lte=interface network.lte.proto='ncm' network.lte.device='/dev/ttyACM0' network.lte.pdptype='IPV4V6' network.lte.apn='internet.telekom' network.lte.ipv6='auto' network.lte.delay='10' The WWAN card is running a modified version of OpenWrt and handles power-management as well as the LED controller (AW9523). A root shell can be acquired by installing adb using opkg and executing "adb shell". Signed-off-by: David Bauer <mail@david-bauer.net>	2022-09-08 13:57:18 +02:00
Albin Hellström	f8c87aa2d2	ath79: add support for Extreme Networks WS-AP3805i Specifications: - SoC: Qualcomm Atheros QCA9557-AT4A - RAM: 2x 128MB Nanya NT5TU64M16HG - FLASH: 64MB - SPANSION FL512SAIFG1 - LAN: Atheros AR8035-A (RGMII GbE with PoE+ IN) - WLAN2: Qualcomm Atheros QCA9557 2x2 2T2R - WLAN5: Qualcomm Atheros QCA9882-BR4A 2x2 2T2R - SERIAL: UART pins at J10 (115200 8n1) Pinout is 3.3V - GND - TX - RX (Arrow Pad is 3.3V) - LEDs: Power (Green/Amber) WiFi 5 (Green) WiFi 2 (Green) - BTN: Reset Installation: 1. Download the OpenWrt initramfs-image. Place it into a TFTP server root directory and rename it to 1D01A8C0.img Configure the TFTP server to listen at 192.168.1.66/24. 2. Connect the TFTP server to the access point. 3. Connect to the serial console of the access point. Attach power and interrupt the boot procedure when prompted. Credentials are admin / new2day 4. Configure U-Boot for booting OpenWrt from ram and flash: $ setenv boot_openwrt 'setenv bootargs; bootm 0xa1280000' $ setenv ramboot_openwrt 'setenv serverip 192.168.1.66; tftpboot 0x89000000 1D01A8C0.img; bootm' $ setenv bootcmd 'run boot_openwrt' $ saveenv 5. Load OpenWrt into memory: $ run ramboot_openwrt 6. Transfer the OpenWrt sysupgrade image to the device. Write the image to flash using sysupgrade: $ sysupgrade -n /path/to/openwrt-sysupgrade.bin Signed-off-by: Albin Hellström <albin.hellstrom@gmail.com> [rename vendor - minor style fixes - update commit message] Signed-off-by: David Bauer <mail@david-bauer.net>	2022-08-29 01:09:17 +02:00
Sebastian Schaper	a434795809	ath79: add support for ZyXEL NWA1100-NH Specifications: * AR9342, 16 MiB Flash, 64 MiB RAM, 802.11n 2T2R, 2.4 GHz * 1x Gigabit Ethernet (AR8035), 802.3af PoE Installation: * OEM Web UI is at 192.168.1.2 login as `admin` with password `1234` * Flash factory-AASI.bin The string `AASI` needs to be present within the file name of the uploaded image to be accepted by the OEM Web-based updater, the factory image is named accordingly to save the user from the hassle of manual renaming. TFTP Recovery: * Open the case, connect to TTL UART port (this is the official method described by Zyxel, the reset button is useless during power-on) * Extract factory image (.tar.bz2), serve `vmlinux_mi124_f1e.lzma.uImage` and `mi124_f1e-jffs2` via tftp at 192.168.1.10 * Interrupt uboot countdown, execute commands `run lk` `run lf` to flash the kernel / filesystem accordingly MAC addresses as verified by OEM firmware: use address source LAN :cc mib0 0x30 ('eth0mac'), art 0x1002 (label) 2g :cd mib0 0x4b ('wifi0mac') Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>	2022-08-21 00:09:53 +02:00
Sebastian Schaper	a6e0ca96da	ath79: add support for ZyXEL NWA1123-AC Specifications: * AR9342, 16 MiB Flash, 64 MiB RAM, 802.11n 2T2R, 2.4 GHz * QCA9882 PCIe card, 802.11ac 2T2R * 1x Gigabit Ethernet (AR8035), 802.3af PoE Installation: * OEM Web UI is at 192.168.1.2 login as `admin` with password `1234` * Flash factory-AAOX.bin The string `AAOX` needs to be present within the file name of the uploaded image to be accepted by the OEM Web-based updater, the factory image is named accordingly to save the user from the hassle of manual renaming. TFTP Recovery: * Open the case, connect to TTL UART port (this is the official method described by Zyxel, the reset button is useless during power-on) * Extract factory image (.tar.bz2), serve `vmlinux_mi124_f1e.lzma.uImage` and `mi124_f1e-jffs2` via tftp at 192.168.1.10 * Interrupt uboot countdown, execute commands `run lk` `run lf` to flash the kernel / filesystem accordingly MAC addresses as verified by OEM firmware: use address source LAN :1c mib0 0x30 ('eth0mac'), art 0x1002 (label) 2g :1c mib0 0x4b ('wifi0mac') 5g *:1e mib0 0x66 ('wifi1mac') Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>	2022-08-21 00:09:53 +02:00
Sebastian Schaper	527be5a456	ath79: add support for ZyXEL NWA1123-NI Specifications: * AR9342, 16 MiB Flash, 64 MiB RAM, 802.11n 2T2R, 2.4 GHz * AR9382 PCIe card, 802.11n 2T2R, 5 GHz * 1x Gigabit Ethernet (AR8035), 802.3af PoE Installation: * OEM Web UI is at 192.168.1.2 login as `admin` with password `1234` * Flash factory-AAEO.bin The string `AAEO` needs to be present within the file name of the uploaded image to be accepted by the OEM Web-based updater, the factory image is named accordingly to save the user from the hassle of manual renaming. TFTP Recovery: * Open the case, connect to TTL UART port (this is the official method described by Zyxel, the reset button is useless during power-on) * Extract factory image (.tar.bz2), serve `vmlinux_mi124_f1e.lzma.uImage` and `mi124_f1e-jffs2` via tftp at 192.168.1.10 * Interrupt uboot countdown, execute commands `run lk` `run lf` to flash the kernel / filesystem accordingly MAC addresses as verified by OEM firmware: use address source LAN :fb mib0 0x30 ('eth0mac'), art 0x1002 (label) 2g :fc mib0 0x4b ('wifi0mac') 5g *:fd mib0 0x66 ('wifi1mac') Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>	2022-08-21 00:09:53 +02:00
Sebastian Schaper	251ecfe379	ath79: add support for ZyXEL NWA1121-NI Specifications: * AR9342, 16 MiB Flash, 64 MiB RAM, 802.11n 2T2R, 2.4 GHz * 1x Gigabit Ethernet (AR8035), 802.3af PoE Installation: * OEM Web UI is at 192.168.1.2 login as `admin` with password `1234` * Flash factory-AABJ.bin The string `AABJ` needs to be present within the file name of the uploaded image to be accepted by the OEM Web-based updater, the factory image is named accordingly to save the user from the hassle of manual renaming. TFTP Recovery: * Open the case, connect to TTL UART port (this is the official method described by Zyxel, the reset button is useless during power-on) * Extract factory image (.tar.bz2), serve `vmlinux_mi124_f1e.lzma.uImage` and `mi124_f1e-jffs2` via tftp at 192.168.1.10 * Interrupt uboot countdown, execute commands `run lk` `run lf` to flash the kernel / filesystem accordingly MAC addresses as verified by OEM firmware: use address source LAN :cc mib0 0x30 ('eth0mac'), art 0x1002 (label) 2g :cd mib0 0x4b ('wifi0mac') Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>	2022-08-21 00:09:53 +02:00
Manuel Niekamp	0dc5821489	ath79: add support for Sophos AP15 The Sophos AP15 seems to be very close to Sophos AP55/AP100. Based on: commit `6f1efb2898` ("ath79: add support for Sophos AP100/AP55 family") author Andrew Powers-Holmes <andrew@omnom.net> Fri, 3 Sep 2021 15:53:57 +0200 (23:53 +1000) committer Hauke Mehrtens <hauke@hauke-m.de> Sat, 16 Apr 2022 16:59:29 +0200 (16:59 +0200) Unique to AP15: - Green and yellow LED - 2T2R 2.4GHz 802.11b/g/n via SoC WMAC - No buttons - No piezo beeper - No 5.8GHz Flashing instructions: - Derived from UART method described in referenced commit, methods described there should work too. - Set up a TFTP server; IP address has to be 192.168.99.8/24 - Copy the firmware (initramfs-kernel) to your TFTP server directory renaming it to e.g. boot.bin - Open AP's enclosure and locate UART header (there is a video online) - Terminal connection parameters are 115200 8/N/1 - Connect TFTP server and AP via ethernet - Power up AP and cancel autoboot when prompted - Prompt shows 'ath> ' - Commands used to boot: ath> tftpboot 0x81000000 boot.bin ath> bootm 0x81000000 - Device should boot OpenWRT - IP address after boot is 192.168.1.1/24 - Connect to device via browser - Permanently flash using the web ui (flashing sysupgrade image) - (BTW: the AP55 images seem to work too, only LEDs are not working) Testing done: - To be honest: Currently not so much testing done. - Flashed onto two devices - Devices are booting - MAC addresses are correct - LEDs are working - Scanning for WLANs is working Big thanks to all the people working on this great project! (Sorry about my english, it is not my native language) Signed-off-by: Manuel Niekamp <m.niekamp@richter-leiterplatten.de>	2022-08-06 20:33:59 +02:00
Jan-Niklas Burfeind	75dffdc8cf	ath79: add variant UniFi AP LR The hardware difference is the antenna which has a higher gain compared to the original UniFi AP. The variant was supported before in ar71xx. Signed-off-by: Jan-Niklas Burfeind <git@aiyionpri.me>	2022-08-06 20:15:30 +02:00
Jan-Niklas Burfeind	50e1f3d84d	ath79: rename references of UniFi to UniFi AP extract the compatible and model to make room for other variants follow-up of commit `dc23df8a8c` ("ath79: change Ubiquiti UniFi AP model name to include "AP"") Signed-off-by: Jan-Niklas Burfeind <git@aiyionpri.me>	2022-08-06 20:15:30 +02:00
Luiz Angelo Daros de Luca	6e0f0eae5b	ath79: use rtl8366s and rtl8366_smi as a module rtl8366s is used only by dlink_dir-825-b1 and the netgear_wndr family (wndr3700, wndr3700-v2, wndr3800ch, wndr3800.dts, wndrmac-v1, wndrmac-v2). Not tested in real hardware. With rtl8366rb, rtl8366s, rtl8367 as modules, rtl8366_smi can also be a loadable module. This change was tested with tl-wr2543-v1. Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>	2022-07-01 20:22:53 +02:00
Luiz Angelo Daros de Luca	b168a07799	ath79: use rtl8367 as a module rtl8367 is used only by tl-wr2543-v1. Tested both normal and failsafe modes. Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>	2022-07-01 20:22:52 +02:00
Luiz Angelo Daros de Luca	575ec7a4b1	ath79: use rtl8366rb as a module It looks like rtl8366rb is used only by tplink_tl-wr1043nd-v1 and buffalo_wzr-hp-g300nh-rb. There is no need to have it built-in as it works as a loadable module. Tested both failsafe and normal boot on tl-wr1043nd-v1. buffalo_wzr-hp-g300nh-rb was not tested. Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>	2022-07-01 20:22:52 +02:00
Tamas Balogh	416d4483e8	ath79: add support for ASUS RP-AC51 Asus RP-AC51 Repeater Category: AC750 300+433 (OEM w. unstable driver) AC1200 300+866 (OpenWrt w. stable driver) Hardware specifications: Board: AP147 SoC: QCA9531 2.4G b/g/n WiFi: QCA9886 5G n/ac DRAM: 128MB DDR2 Flash: gd25q128 16MB SPI-NOR LAN/WAN: AR8229 1x100M Clocks: CPU:650MHz, DDR:600MHz, AHB:200MHz MAC addresses as verified by OEM firmware: use address source Lan/W2G :C8 art 0x1002 (label) 5G :CC art 0x5006 Installation: Asus windows recovery tool: install the Asus firmware restoration utility unplug the router, hold the reset button while powering it on release when the power LED flashes slowly specify a static IP on your computer: IP address: 192.168.1.75 Subnet mask 255.255.255.0 Start the Asus firmware restoration utility, specify the factory image and press upload Do not power off the device after OpenWrt has booted until the LED flashing. TFTP Recovery method: set computer to a static ip, 192.168.1.10 connect computer to the LAN 1 port of the router hold the reset button while powering on the router for a few seconds send firmware image using a tftp client; i.e from linux: $ tftp tftp> binary tftp> connect 192.168.1.1 tftp> put factory.bin tftp> quit Signed-off-by: Tamas Balogh <tamasbalogh@hotmail.com>	2022-06-30 00:23:42 +02:00
Tamas Balogh	e1dcaeb55c	ath79: add support for ASUS PL-AC56 Asus PL-AC56 Powerline Range Extender Rev.A1 (in kit with Asus PL-E56P Powerline-slave) Hardware specifications: Board: AP152 SoC: QCA9563 2.4G n 3x3 PLC: QCA7500 WiFi: QCA9882 5G ac 2x2 Switch: QCA8337 3x1000M Flash: 16MB 25L12835F SPI-NOR DRAM SoC: 64MB w9751g6kb-25 DRAM PLC: 128MB w631gg6kb-15 Clocks: CPU:775.000MHz, DDR:650.000MHz, AHB:258.333MHz, Ref:25.000MHz MAC addresses as verified by OEM firmware: use address source Lan/Wan/PLC :10 art 0x1002 (label) 2G :10 art 0x1000 5G *:14 art 0x5000 Important notes: the PLC firmware has to be provided and copied manually onto the device! The PLC here has no dedicated flash, thus the firmware file has to be uploaded to the PLC controller at every system start the PLC functionality is managed by the script /etc/init.d/plc_basic, a very basic script based on the the one from Netadair (netadair dot de) Installation: Asus windows recovery tool: have to have the latest Asus firmware flashed before continuing! install the Asus firmware restoration utility unplug the router, hold the reset button while powering it on release when the power LED flashes slowly specify a static IP on your computer: IP address: 192.168.1.75 Subnet mask 255.255.255.0 start the Asus firmware restoration utility, specify the factory image and press upload do NOT power off the device after OpenWrt has booted until the LED flashing TFTP Recovery method: have to have the latest Asus firmware flashed before continuing! set computer to a static ip, 192.168.1.75 connect computer to the LAN 1 port of the router hold the reset button while powering on the router for a few seconds send firmware image using a tftp client; i.e from linux: $ tftp tftp> binary tftp> connect 192.168.1.1 tftp> put factory.bin tftp> quit do NOT power off the device after OpenWrt has booted until the LED flashing Additional notes: the pairing buttons have to have pressed for at least half a second, it doesn't matter on which plc device (master or slave) first it is possible to pair the devices without the button-pairing requirement simply by pressing reset on the slave device. This will default to the firmware settings, which is also how the plc_basic script is setting up the master device, i.e. configuring it to firmware defaults the PL-E56P slave PLC has its dedicated 4MByte SPI, thus it is capable to store all firmware currently available. Note that some other slave devices are not guarantied to have the capacity for the newer ~1MByte firmware blobs! To have a good overlook about the slave device, here are its specs: same QCA7500 PLC controller, same w631gg6kb-15 128MB RAM, 25L3233F 4MB SPI-NOR and an AR8035-A 1000M-Transceiver Signed-off-by: Tamas Balogh <tamasbalogh@hotmail.com>	2022-06-30 00:16:59 +02:00
Thibaut VARÈNE	e1223dbee3	ath79: add support for RouterBOARD mAP The MikroTik mAP-2nd (sold as mAP) is an indoor 2.4Ghz AP with 802.3af/at PoE input and passive PoE passthrough. See https://mikrotik.com/product/RBmAP2nD for more details. Specifications: - SoC: QCA9533 - RAM: 64MB - Storage: 16MB NOR - Wireless: QCA9533 802.11b/g/n 2x2 - Ethernet: 2x 10/100 ports, 802.3af/at PoE in port 1, 500 mA passive PoE out on port 2 - 7 user-controllable LEDs Note: the device is a tiny AP and does not distinguish between both ethernet ports roles, so they are both assigned to lan. With the current setup, ETH1 is connected to eth1 and ETH2 is connected to eth0 via the embedded switch port 2. Flashing: TFTP boot initramfs image and then perform sysupgrade. The "ETH1" port must be used to upload the TFTP image. Follow common MikroTik procedure as in https://openwrt.org/toh/mikrotik/common. Tested-By: Andrew Powers-Holmes <aholmes@omnom.net> Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>	2022-06-29 12:36:04 +02:00
Sven Hauer	7e21ce8e2b	ath79: support for TP-Link EAP225 v4 This model is almost identical to the EAP225 v3. Major difference is the RTL8211FS PHY Chipset. Device specifications: * SoC: QCA9563 @ 775MHz * RAM: 128MiB DDR2 * Flash: 16MiB SPI-NOR * Wireless 2.4GHz (SoC): b/g/n, 3x3 * Wireless 5Ghz (QCA9886): a/n/ac, 2x2 MU-MIMO * Ethernet (RTL8211FS): 1× 1GbE, 802.3at PoE Flashing instructions: * ssh into target device and run `cliclientd stopcs` * Upgrade with factory image via web interface Debricking: * Serial port can be soldered on PCB J4 (1: TXD, 2: RXD, 3: GND, 4: VCC) * Bridge unpopulated resistors R225 (TXD) and R237 (RXD). Do NOT bridge R230. * Use 3.3V, 115200 baud, 8n1 * Interrupt bootloader by holding CTRL+B during boot * tftp initramfs to flash via LuCI web interface setenv ipaddr 192.168.1.1 # default, change as required setenv serverip 192.168.1.10 # default, change as required tftp 0x80800000 initramfs.bin bootelf $fileaddr MAC addresses: MAC address (as on device label) is stored in device info partition at an offset of 8 bytes. ath9k device has same address as ethernet, ath10k uses address incremented by 1. Signed-off-by: Sven Hauer <sven.hauer+github@uniku.de>	2022-06-28 10:58:16 +02:00
Sebastian Schaper	f770c33d7b	ath79: fix rootfs padding for D-Link DAP-2xxx It was observed that `rootfs_data` was sometimes not correctly erased after performing sysupgrade, resulting in previous settings to prevail. Add call to `wrgg-pad-rootfs` in sysupgrade image recipe to ensure any previous jffs2 will be wiped, consistent with DAP-2610 from the ipq40xx target, which introduced the double-flashing procedure for these devices. Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>	2022-06-24 17:10:24 +02:00
Tomasz Maciej Nowak	9decd2a843	ath79: bsap18x0: pad rootfs image This image is supposed to be written with help of bootloader to the flash, but as it stands, it's not aligned to block size and RedBoot will happily create non-aligned partition size in FIS directory. This could lead to kernel to mark the partition as read-only, therefore pad the image to block erase size boundary. Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>	2022-06-24 17:10:24 +02:00
Tomasz Maciej Nowak	5c142aad7b	ath79: switch some RedBoot based devices to OKLI loader After the kernel has switched version to 5.10, JA76PF2 and RouterStations lost the capability to sysupgrade the OpenWrt version. The cause is the lack of porting the patches responsible for partial flash erase block writing and these boards FIS directory and RedBoot config partitions share the same erase block. Because of that the FIS directory can't be updated to accommodate kernel/rootfs partition size changes. This could be remedied by bootloader update, but it is very intrusive and could potentially lead to non-trivial recovery procedure, if something went wrong. The less difficult option is to use OpenWrt kernel loader, which will let us use static partition sizes and employ mtd splitter to dynamically adjust kernel and rootfs partition sizes. On sysupgrade from ath79 19.07 or 21.02 image, which still let to modify FIS directory, the loader will be written to kernel partition, while the kernel+rootfs to rootfs partition. The caveats are: * image format changes, no possible upgrade from ar71xx target images * downgrade to any older OpenWrt version will require TFTP recovery or usage of bootloader command line interface To downgrade to 19.07 or 21.02, or to upgrade if one is already on OpenWrt with kernel 5.10, for RouterStations use TFTP recovery procedure. For JA76PF2 use instructions from this commit message: commit `0cc87b3bac` ("ath79: image: disable sysupgrade images for routerstations and ja76pf2"), replacing kernel image with loader (loader.bin suffix) and rootfs image with firmware (firmware.bin suffix). Fixes: `b10d604459` ("kernel: add linux 5.10 support") Fixes: `15aa53d7ee` ("ath79: switch to Kernel 5.10") Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com> (mkubntimage was moved to generic-ubnt.mk) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>	2022-06-24 17:09:54 +02:00
Tomasz Maciej Nowak	4cca0947ff	ath79: jj76pf2: enable TCN75 sensor This SBC has Microchip TCN75 sensor, wich measures ambient temperature. Specify it in dts to allow readout by applications using kernel hwmon API. Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>	2022-06-24 17:09:53 +02:00
Paul Maruhn	7e4de89e63	ath79: support for TP-Link EAP225-Outdoor v3 This model is almost identical to the EAP225-Outdoor v1. Major difference is the RTL8211FS PHY Chipset. Device specifications: * SoC: QCA9563 @ 775MHz * Memory: 128MiB DDR2 * Flash: 16MiB SPI-NOR * Wireless 2.4GHz (SoC): b/g/n 2x2 * Wireless 5GHz (QCA9886): a/n/ac 2x2 MU-MIMO * Ethernet (RTL8211FS): 1× 1GbE, PoE Flashing instructions: * ssh into target device with recent (>= v1.6.0) firmware * run `cliclientd stopcs` on target device * upload factory image via web interface Debricking: To recover the device, you need access to the serial port. This requires fine soldering to test points, or the use of probe pins. * Open the case and solder wires to the test points: RXD, TXD and TPGND4 * Use a 3.3V UART, 115200 baud, 8n1 * Interrupt bootloader by holding ctrl+B during boot * upload initramfs via built-in tftp client and perform sysupgrade setenv ipaddr 192.168.1.1 # default, change as required setenv serverip 192.168.1.10 # default, change as required tftp 0x80800000 initramfs.bin bootelf $fileaddr MAC addresses: MAC address (as on device label) is stored in device info partition at an offset of 8 bytes. ath9k device has same address as ethernet, ath10k uses address incremented by 1. From stock ifconfig: ath0 Link encap:Ethernet HWaddr D8:...:2E ath10 Link encap:Ethernet HWaddr D8:...:2F br0 Link encap:Ethernet HWaddr D8:...:2E eth0 Link encap:Ethernet HWaddr D8:...:2E Signed-off-by: Paul Maruhn <paulmaruhn@posteo.de> Co-developed-by: Philipp Rothmann <philipprothmann@posteo.de> Signed-off-by: Philipp Rothmann <philipprothmann@posteo.de> [Add pre-calibraton nvme-cells] Tested-by: Tido Klaassen <tido_ff@4gh.eu> Signed-off-by: Nick Hainke <vincent@systemli.org>	2022-06-22 17:47:11 +02:00
Chris Blake	949e8ba521	ath79: add support for Netgear PGZNG1 This adds support for the Netgear PGZNG1, also known as the ADT Pulse Gateway. Hardware: CPU: Atheros AR9344 Memory: 256MB Storage: 256MB NAND Hynix H27U2G8F2CTR-BC USB: 1x USB 2.0 Ethernet: 2x 100Mb/s WiFi: Atheros AR9340 2.4GHz 2T2R Leds: 8 LEDs Button: 1x Reset Button UART: Header marked JPE1. Pinout is VCC, TX, RX, GND. The marked pin, closest to the JPE1 marking, is VCC. Note VCC isn't required to be connected for UART to work. Enable Stock Firmware Shell Access: 1. Interrupt u-boot and run the following commands setenv console_mode 1 saveenv reset This will enable a UART shell in the firmware. You can then login using the root password of `icontrol`. If that doesn't work, the device is running a firmware based on OpenWRT where you can drop into failsafe to mount the FS and then modify /etc/passwd. Installation Instructions: 1. Interupt u-boot and run the following commands setenv active_image 0 setenv stock_bootcmd nboot 0x81000000 0 \${kernel_offset} setenv openwrt_bootcmd nboot 0x82000000 0 \${kernel_offset} setenv bootcmd run openwrt_bootcmd saveenv 2. boot initramfs image via TFTP u-boot tftpboot 0x82000000 openwrt-ath79-nand-netgear_pgzng1-initramfs-kernel.bin; bootm 0x82000000 3. Once booted, use LuCI sysupgrade to flash openwrt-ath79-nand-netgear_pgzng1-squashfs-sysupgrade.bin MAC Table: WAN (eth0): xx:xa - caldata 0x0 LAN (eth1): xx:xb - caldata 0x6 WLAN (phy0): xx:xc - burned into ath9k caldata Not Working: Z-Wave RS422 Signed-off-by: Chris Blake <chrisrblake93@gmail.com> (added more hw-info, fixed file permissions) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>	2022-06-19 12:31:02 +02:00
Nick Hainke	f4415f7635	ath79: move ubnt-xm to tiny ath79 has was bumped to 5.10. With this, as with every kernel change, the kernel has become larger. However, although the kernel gets bigger, there are still enough flash resources. But the RAM reaches its capacity limits. The tiny image comes with fewer kernel flags enabled and fewer daemons. Improves: `15aa53d7ee` ("ath79: switch to Kernel 5.10") Tested-by: Robert Foss <me@robertfoss.se> Signed-off-by: Nick Hainke <vincent@systemli.org>	2022-06-11 21:22:58 +02:00
Stijn Segers	0dc056eb66	ath79: D-Link DAP-2680: select QCA9984 firmware The DAP-2680 has a QCA9984 radio [1], but the commit adding support mistakenly adds the QCA99x0 firmware package. See forum topic [2]. [1] https://wikidevi.wi-cat.ru/D-Link_DAP-2680_rev_A1 [2] https://forum.openwrt.org/t/missing-5ghz-radio-on-dlink-dap-2680/ Fixes: `5b58710fad` ("ath79: add support for D-Link DAP-2680 A1") Signed-off-by: Stijn Segers <foss@volatilesystems.org> Tested-by: Alessandro Fellin <af.registrazioni@gmail.com>	2022-06-11 10:20:06 +02:00
Jan-Niklas Burfeind	21a3ce97d5	ath79: NanoBeam M5 fix target_devices Update the name of for the Ubiquiti NanoBeam M5 to match the auto-generated one at runtime. Otherwise sysupgrade complains about mismatching device names. This also required renaming the DTS. Signed-off-by: Jan-Niklas Burfeind <git@aiyionpri.me>	2022-05-21 19:24:40 +02:00
Jan-Niklas Burfeind	4cd3ff8a79	ath79: add support for Ubiquiti NanoBeam M5 Ubiquiti NanoBeam M5 devices are CPE equipment for customer locations with one Ethernet port and a 5 GHz 300Mbps wireless interface. Specificatons: - Atheros AR9342 - 535 MHz CPU - 64 MB RAM - 8 MB Flash - 1x 10/100 Mbps Ethernet with passive PoE input (24 V) - 6 LEDs of which four are rssi - 1 reset button - UART (4-pin) header on PCB Notes: The device was supported by OpenWrt in ar71xx. Flash instructions (web/ssh/tftp): Loading the image via ssh vias a stock firmware prior "AirOS 5.6". Downgrading stock is possible. * Flashing is possible via AirOS software update page: The "factory" ROM image is recognized as non-native and then installed correctly. AirOS warns to better be familiar with the recovery procedure. * Flashing can be done via ssh, which is becoming difficult due to legacy keyexchange methods. This is an exempary ssh-config: KexAlgorithms +diffie-hellman-group1-sha1 HostKeyAlgorithms ssh-rsa PubkeyAcceptedKeyTypes ssh-rsa User ubnt The password is ubnt. Connecting via IPv6 link local worked best for me. 1. scp the factory image to /tmp 2. fwupdate.real -m /tmp/firmware_image_file.bin -d * Alternatively tftp is possible: 1. Configure PC with static IP 192.168.1.2/24. 2. Enter the rescue mode. Power off the device, push the reset button on the device (or the PoE) and keep it pressed. Power on the device, while still pushing the reset button. 3. When all the leds blink at the same time, release the reset button. 4. Upload the firmware image file via TFTP: tftp 192.168.1.20 tftp> bin tftp> trace Packet tracing on. tftp> put firmware_image.bin Signed-off-by: Jan-Niklas Burfeind <git@aiyionpri.me>	2022-05-21 13:54:15 +02:00
Maciej Krüger	5ce64e0646	ath79: add support for MikroTik hAP (RB951Ui-2nD) The MikroTik hAP (product code RB951Ui-2nD) is an indoor 2.4Ghz AP with a 2 dBi integrated antenna built around the Atheros QCA9531 SoC. Specifications: - SoC: Atheros QCA9531 - RAM: 64 MB - Storage: 16 MB NOR - Winbond 25Q128FVSG - Wireless: Atheros QCA9530 (SoC) 802.11b/g/n 2x2 - Ethernet: Atheros AR934X switch, 5x 10/100 ports, 10-28 V passive PoE in port 1, 500 mA PoE out on port 5 - 8 user-controllable LEDs: · 1x power (green) · 1x user (green) · 4x LAN status (green) · 1x WAN status (green) · 1x PoE power status (red) See https://mikrotik.com/product/RB951Ui-2nD for more details. Notes: The device was already supported in the ar71xx target. Flashing: TFTP boot initramfs image and then perform sysupgrade. Follow common MikroTik procedure as in https://openwrt.org/toh/mikrotik/common. Signed-off-by: Maciej Krüger <mkg20001@gmail.com>	2022-05-21 13:54:08 +02:00
Thibaut VARÈNE	2bd33e8626	ath79: add support for MikroTik RouterBOARD hAP ac lite The MikroTik RB952Ui-5ac2nD (sold as hAP ac lite) is an indoor 2.4Ghz and 5GHz AP/router with a 2 dBi integrated antenna. See https://mikrotik.com/product/RB952Ui-5ac2nD for more details. Specifications: - SoC: QCA9533 - RAM: 64MB - Storage: 16MB NOR - Wireless: QCA9533 802.11b/g/n 2x2 / QCA9887 802.11a/n/ac 2x2 - Ethernet: AR934X switch, 5x 10/100 ports, 10-28 V passive PoE in port 1, 500 mA PoE out on port 5 - 6 user-controllable LEDs: - 1x user (green) - 5x port status (green) Flashing: TFTP boot initramfs image and then perform sysupgrade. The "Internet" port (port number 1) must be used to upload the TFTP image, then connect to any other port to access the OpenWRT system. Follow common MikroTik procedure as in https://openwrt.org/toh/mikrotik/common. Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>	2022-05-21 13:54:02 +02:00
Nick Hainke	88527294cd	ath79: add Netgear WNDAP360 SoC: Atheros AR7161 RAM: DDR 128 MiB (hynix h5dU5162ETR-E3C) Flash: SPI-NOR 8 MiB (mx25l6406em2i-12g) WLAN: 2.4/5 GHz 2.4 GHz: Atheros AR9220 5 GHz: Atheros AR9223 Ethernet: 4x 10/100/1000 Mbps (Atheros AR8021) LEDs/Keys: 2/2 (Internet + System LED, Mesh button + Reset pin) UART: RJ45 9600,8N1 Power: 12 VDC, 1.0 A Installation instruction: 0. Make sure you have latest original firmware (3.7.11.4) 1. Connect to the Serial Port with a Serial Cable RJ45 to DB9/RS232 (9600,8N1) screen /dev/ttyUSB0 9600,cs8,-parenb,-cstopb,-hupcl,-crtscts,clocal 2. Configure your IP-Address to 192.168.1.42 3. When device boots hit spacebar 3. Configure the device for tftpboot setenv ipaddr 192.168.1.1 setenv serverip 192.168.1.42 saveenv 4. Reset the device reset 5. Hit again the spacebar 6. Now load the image via tftp: tftpboot 0x81000000 INITRAMFS.bin 7. Boot the image: bootm 0x81000000 8. Copy the squashfs-image to the device. 9. Do a sysupgrade. https://openwrt.org/toh/netgear/wndap360 The device should be converted from kmod-owl-loader to nvmem-cells in the future. Nvmem cells were not working. Maybe ATH9K_PCI_NO_EEPROM is missing. That is why this commit is still using kmod-owl-loader. In the future the device tree may look like this: &ath9k0 { nvmem-cells = <&macaddr_art_120c>, <&cal_art_1000>; nvmem-cell-names = "mac-address", "calibration"; }; &ath9k1 { nvmem-cells = <&macaddr_art_520c>, <&cal_art_5000>; nvmem-cell-names = "mac-address", "calibration"; }; &art { ... cal_art_1000: cal@1000 { reg = <0x1000 0xeb8>; }; cal_art_5000: cal@5000 { reg = <0x5000 0xeb8>; }; }; Signed-off-by: Nick Hainke <vincent@systemli.org>	2022-04-30 23:56:47 +02:00
Foica David	063e9047cc	ath79: add support for TP-Link Deco M4R v1 and v2 This commit adds support for the TP-Link Deco M4R (it can also be M4, TP-Link uses both names) v1 and v2. It is similar hardware-wise to the Archer C6 v2. Software-wise it is very different. V2 has a bit different layout from V1 but the chips are the same and the OEM firmware is the same for both versions. Specifications: SoC: QCA9563-AL3A RAM: Zentel A3R1GE40JBF Wireless 2.4GHz: QCA9563-AL3A (main SoC) Wireless 5GHz: QCA9886 Ethernet Switch: QCA8337N-AL3C Flash: 16 MB SPI NOR Flashing: The device's bootloader only accepts images that are signed using TP-Link's RSA key, therefore this way of flashing is not possible. The device has a web GUI that should be accessible after setting up the device using the app (it requires the app to set it up first because the web GUI asks for the TP-Link account password) but for unknown reasons, the web GUI also refuses custom images. There is a debug firmware image that has been shared on the device's OpenWrt forum thread that has telnet unlocked, which the bootloader will accept because it is signed. It can be used to transfer an OpenWrt image file over to the device and then be used with mtd to flash the device. Pre-requisites: - Debug firmware. - A way of transferring the file to the router, you can use an FTP server as an example. - Set a static IP of 192.168.0.2/255.255.255.0 on your computer. - OpenWrt image. Installation: - Unplug your router and turn it upside down. Using a long and thin object like a SIM unlock tool, press and hold the reset button on the router and replug it. Keep holding it until the LED flashes yellow. - Open 192.168.0.1. You should see the bootloader recovery's webpage. Choose the debug firmware that you downloaded and flash it. Wait until the router reboots (at this stage you can remove the static IP). - Open a terminal window and connect to the router via telnet (the primary router should have a 192.168.0.1 IP address, secondary routers are different). - Transfer the file over to the router, you can use curl to download it from the internet (use the insecure flag and make sure your source accepts insecure downloads) or from an FTP server. - The router's default mtd partition scheme has kernel and rootfs separated. We can use dd to split the OpenWrt image file and flash it with mtd: dd if=openwrt.bin of=kernel.bin skip=0 count=8192 bs=256 dd if=openwrt.bin of=rootfs.bin skip=8192 bs=256 - Once the images are ready, you have to flash the device using mtd (make sure to flash the correct partitions or you may be left with a hard bricked router): mtd write kernel.bin kernel mtd write rootfs.bin rootfs - Flashing is done, reboot the device now. Signed-off-by: Foica David <superh552@gmail.com>	2022-04-30 23:56:47 +02:00
Sander Vanheule	8fa4361f55	ath79: add support for TP-Link EAP265 HD The EAP265 HD is a rebadged EAP245v3, so images are compatible with both devices. Link: https://fccid.io/TE7EAP265HD/Letter/6-Request-for-FCC-Change-ID-4823578.pdf Signed-off-by: Sander Vanheule <sander@svanheule.net>	2022-04-27 20:29:37 +02:00
Martin Weinelt	089eb02abc	ath79: ubnt: drop swconfig on ac-{lite,lr,mesh} These don't have switches that could be configured using swconfig. Signed-off-by: Martin Weinelt <hexa@darmstadt.ccc.de>	2022-04-23 22:22:12 +02:00
Lech Perczak	8a1003c598	ath79: ZTE MF286R: add comgt-ncm to DEVICE_PACKAGES When adding support to the router's built-in modem, this required package was omitted, because it was already enabled in the image configuration in use for testing, and this went unnoticed. In result, the modem still isn't fully supported in official images. As it is the primary WAN interface, add the missing package. Fixes: `e02fb42c53` ("comgt: support ZTE MF286R modem") Signed-off-by: Lech Perczak <lech.perczak@gmail.com>	2022-04-23 20:46:25 +02:00
David Musil	e20de22442	ath79: add support for MikroTik RouterBOARD wAP-2nD (wAP) The MikroTik RouterBOARD wAP-2nd (sold as wAP) is a small 2.4 GHz 802.11b/g/n PoE-capable AP. Specifications: - SoC: Qualcomm Atheros QCA9533 - Flash: 16 MB (SPI) - RAM: 64 MB - Ethernet: 1x 10/100 Mbps (PoE in) - WiFi: AR9531 2T2R 2.4 GHz (SoC) - 3x green LEDs (1x lan, 1x wlan, 1x user) See https://mikrotik.com/product/RBwAP2nD for more info. Flashing: TFTP boot initramfs image and then perform sysupgrade. Follow common MikroTik procedure as in https://openwrt.org/toh/mikrotik/common. Note: following `781d4bfb39` The network setup avoids using the integrated switch and connects the single Ethernet port directly. This way, link speed (10/100 Mbps) is properly reported by eth0. Signed-off-by: David Musil <0x444d@protonmail.com>	2022-04-18 07:24:09 +02:00
Andrew Powers-Holmes	6f1efb2898	ath79: add support for Sophos AP100/AP55 family The Sophos AP100, AP100C, AP55, and AP55C are dual-band 802.11ac access points based on the Qualcomm QCA9558 SoC. They share PCB designs with several devices that already have partial or full support, most notably the Devolo DVL1750i/e. The AP100 and AP100C are hardware-identical to the AP55 and AP55C, however the 55 models' ART does not contain calibration data for their third chain despite it being present on the PCB. Specifications common to all models: - Qualcomm QCA9558 SoC @ 720 MHz (MIPS 74Kc Big-endian processor) - 128 MB RAM - 16 MB SPI flash - 1x 10/100/1000 Mbps Ethernet port, 802.3af PoE-in - Green and Red status LEDs sharing a single external light-pipe - Reset button on PCB[1] - Piezo beeper on PCB[2] - Serial UART header on PCB - Alternate power supply via 5.5x2.1mm DC jack @ 12 VDC Unique to AP100 and AP100C: - 3T3R 2.4GHz 802.11b/g/n via SoC WMAC - 3T3R 5.8GHz 802.11a/n/ac via QCA9880 (PCI Express) AP55 and AP55C: - 2T2R 2.4GHz 802.11b/g/n via SoC WMAC - 2T2R 5.8GHz 802.11a/n/ac via QCA9880 (PCI Express) AP100 and AP55: - External RJ45 serial console port[3] - USB 2.0 Type A port, power controlled via GPIO 11 Flashing instructions: This firmware can be flashed either via a compatible Sophos SG or XG firewall appliance, which does not require disassembling the device, or via the U-Boot console available on the internal UART header. To flash via XG appliance: - Register on Sophos' website for a no-cost Home Use XG firewall license - Download and install the XG software on a compatible PC or virtual machine, complete initial appliance setup, and enable SSH console access - Connect the target AP device to the XG appliance's LAN interface - Approve the AP from the XG Web UI and wait until it shows as Active (this can take 3-5 minutes) - Connect to the XG appliance over SSH and access the Advanced Console (Menu option 5, then menu option 3) - Run `sudo awetool` and select the menu option to connect to an AP via SSH. When prompted to enable SSH on the target AP, select Yes. - Wait 2-3 minutes, then select the AP from the awetool menu again. This will connect you to a root shell on the target AP. - Copy the firmware to /tmp/openwrt.bin on the target AP via SCP/TFTP/etc - Run `mtd -r write /tmp/openwrt.bin astaro_image` - When complete, the access point will reboot to OpenWRT. To flash via U-Boot serial console: - Configure a TFTP server on your PC, and set IP address 192.168.99.8 with netmask 255.255.255.0 - Copy the firmware .bin to the TFTP server and rename to 'uImage_AP100C' - Open the target AP's enclosure and locate the 4-pin 3.3V UART header [4] - Connect the AP ethernet to your PC's ethernet port - Connect a terminal to the UART at 115200 8/N/1 as usual - Power on the AP and press a key to cancel autoboot when prompted - Run the following commands at the U-Boot console: - `tftpboot` - `cp.b $fileaddr 0x9f070000 $filesize` - `boot` - The access point will boot to OpenWRT. MAC addresses as verified by OEM firmware: use address source LAN label config 0x201a (label) 2g label + 1 art 0x1002 (also found at config 0x2004) 5g label + 9 art 0x5006 Increments confirmed across three AP55C, two AP55, and one AP100C. These changes have been tested to function on both current master and 21.02.0 without any obvious issues. [1] Button is present but does not alter state of any GPIO on SoC [2] Buzzer and driver circuitry is present on PCB but is not connected to any GPIO. Shorting an unpopulated resistor next to the driver circuitry should connect the buzzer to GPIO 4, but this is unconfirmed. [3] This external RJ45 serial port is disabled in the OEM firmware, but works in OpenWRT without additional configuration, at least on my three test units. [4] On AP100/AP55 models the UART header is accessible after removing the device's top cover. On AP100C/AP55C models, the PCB must be removed for access; three screws secure it to the case. Pin 1 is marked on the silkscreen. Pins from 1-4 are 3.3V, GND, TX, RX Signed-off-by: Andrew Powers-Holmes <andrew@omnom.net>	2022-04-16 16:59:29 +02:00
Ryan Mounce	c2140e32ce	ath79: add support for MikroTik RouterBOARD 962UiGS-5HacT2HnT (hAP ac) This patch adds support for the MikroTik RouterBOARD 962UiGS-5HacT2HnT (hAP ac) Specifications: - SoC: QCA9558 - RAM: 128 MB - Flash: 16 MB SPI - 2.4GHz WLAN: 3x3:3 802.11n on SoC - 5GHz WLAN: 3x3:3 802.11ac on QCA9880 connected via PCIe - Switch: 5x 1000/100/10 on QCA8337 connected via RGMII - SFP cage: connected via SGMII (tested with genuine & generic GLC-T) - USB: 1x type A, GPIO power switch - PoE: Passive input on Ether1, GPIO switched passthrough to Ether5 - Reset button - "SFP" LED connected to SoC - Ethernet LEDs connected to QCA8337 switch - Green WLAN LED connected to QCA9880 Not working: - Red WLAN LED Installation: TFTP boot initramfs image and then perform sysupgrade. Follow common MikroTik procedure as in https://openwrt.org/toh/mikrotik/common. Signed-off-by: Ryan Mounce <ryan@mounce.com.au>	2022-04-16 16:59:29 +02:00
Yousong Zhou	5c147d36ba	ath79: port HiWiFi HC6361 from ar71xx The device was added for ar71xx target and dropped during the ath79 transition, mainly because of the ascii mac address stored in bdinfo partition Device page, http://wiki.openwrt.org/toh/hiwifi/hc6361 The vendor u-boot image accepts sysupgrade.bin image with specific requirements, including having squashfs signature "hsqs" at file offset 0x140000. This is not possible now that OpenWrt kernel image is at least 2MB with the signature at offset 0x240000. Installation of current build of OpenWrt now requires a bootstrap step of installing an earlier version first. - If the vendor u-boot accepts sysupgrade image, hc6361 image of LEDE release should work - If the vendor u-boot accepts only verified flashsmt image, install the one in the above device page. The image is based on Barrier Breaker SHA256SUM of the flashsmt image 81b193b95ea5f8e5c30cd62fa9facf275f39233be4fdeed7038f3deed2736156 After the bootstrap step, current build of OpenWrt can be installed there fine. Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>	2022-04-16 01:27:09 +00:00
Thibaut VARÈNE	a05dcb0724	ath79: add support for Yuncore A930 Specification: - QCA9533 (650 MHz), 64 or 128MB RAM, 16MB SPI NOR - 2x 10/100 Mbps Ethernet, with 802.3at PoE support (WAN) - 2T2R 802.11b/g/n 2.4GHz Flash instructions: If your device comes with generic QSDK based firmware, you can login over telnet (login: root, empty password, default IP: 192.168.188.253), issue first (important!) 'fw_setenv' command and then perform regular upgrade, using 'sysupgrade -n -F ...' (you can use 'wget' to download image to the device, SSH server is not available): fw_setenv bootcmd "bootm 0x9f050000 \|\| bootm 0x9fe80000" sysupgrade -n -F openwrt-...-yuncore_...-squashfs-sysupgrade.bin In case your device runs firmware with YunCore custom GUI, you can use U-Boot recovery mode: 1. Set a static IP 192.168.0.141/24 on PC and start TFTP server with 'tftp' image renamed to 'upgrade.bin' 2. Power the device with reset button pressed and release it after 5-7 seconds, recovery mode should start downloading image from server (unfortunately, there is no visible indication that recovery got enabled - in case of problems check TFTP server logs) Signed-off-by: Clemens Hopfer <openwrt@wireloss.net> Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>	2022-04-15 07:11:18 +02:00
Thibaut VARÈNE	c91df224f5	ath79: add support for Yuncore XD3200 Specification: - QCA9563 (775MHz), 128MB RAM, 16MB SPI NOR - 2T2R 802.11b/g/n 2.4GHz - 2T2R 802.11n/ac 5GHz - 2x 10/100/1000 Mbps Ethernet, with 802.3at PoE support (WAN port) LED for 5 GHz WLAN is currently not supported as it is connected directly to the QCA9882 radio chip. Flash instructions: If your device comes with generic QSDK based firmware, you can login over telnet (login: root, empty password, default IP: 192.168.188.253), issue first (important!) 'fw_setenv' command and then perform regular upgrade, using 'sysupgrade -n -F ...' (you can use 'wget' to download image to the device, SSH server is not available): fw_setenv bootcmd "bootm 0x9f050000 \|\| bootm 0x9fe80000" sysupgrade -n -F openwrt-...-yuncore_...-squashfs-sysupgrade.bin In case your device runs firmware with YunCore custom GUI, you can use U-Boot recovery mode: 1. Set a static IP 192.168.0.141/24 on PC and start TFTP server with 'tftp' image renamed to 'upgrade.bin' 2. Power the device with reset button pressed and release it after 5-7 seconds, recovery mode should start downloading image from server (unfortunately, there is no visible indication that recovery got enabled - in case of problems check TFTP server logs) Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>	2022-04-15 07:11:18 +02:00
Joe Mullally	44e1e5d153	ath79: Move TPLink WPA8630Pv2 to ath79-tiny target These devices only have 6MiB available for firmware, which is not enough for recent release images, so move these to the tiny target. Note for users sysupgrading from the previous ath79-generic snapshot images: The tiny target kernel has a 4Kb flash erase block size instead of the generic target's 64kb. This means the JFFS2 overlay partition containing settings must be reformatted with the new block size or else there will be data corruption. To do this, backup your settings before upgrading, then during the sysupgrade, de-select "Keep Settings". On the CLI, use "sysupgrade -n". If you forget to do this and your system becomes unstable after upgrading, you can do this to format the partition and recover: * Reboot * Press RESET when Power LED blinks during boot to enter Failsafe mode * SSH to 192.168.1.1 * Run "firstboot" and reboot Signed-off-by: Joe Mullally <jwmullally@gmail.com> Tested-by: Robert Högberg <robert.hogberg@gmail.com>	2022-04-09 19:31:46 +02:00
Matthias Schiffer	8ba71f1f6f	ath79: fix TPLINK_HWREV field for TL-WR1043ND v4 Required to allow sysupgrades from OpenWrt 19.07. Closes #7071 Fixes: `98fbf2edc0` ("ath79: move TPLINK_HWID/_HWREV to parent for tplink-safeloader") Tested-by: J. Burfeind <git@aiyionpri.me> Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>	2022-03-25 18:13:11 +01:00
Matthias Schiffer	dc23df8a8c	ath79: change Ubiquiti UniFi AP model name to include "AP" While it hasn't always been clear whether the "AP" is part of the model name on the Ubiquiti website, we include it for all other pre-AC variants (AP Pro and the AP Outdoor+). Add it to the original UniFi AP as well for consistency. Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>	2022-03-24 09:30:35 +01:00
Michael Pratt	41be1a2de2	ath79: add support for Araknis AN-700-AP-I-AC FCC ID: 2AG6R-AN700APIAC Araknis AN-700-AP-I-AC is an indoor wireless access point with 1 Gb ethernet port, dual-band wireless, internal antenna plates, and 802.3at PoE+ this board is a Senao device: the hardware is equivalent to EnGenius EAP1750 the software is modified Senao SDK which is based on openwrt and uboot including image checksum verification at boot time, and a failsafe image that boots if checksum fails Specification: - QCA9558 SOC MIPS 74kc, 2.4 GHz WMAC, 3x3 - QCA9880 WLAN PCI card, 5 GHz, 3x3, 26dBm - AR8035-A PHY RGMII GbE with PoE+ IN - 40 MHz clock - 16 MB FLASH MX25L12845EMI-10G - 2x 64 MB RAM NT5TU32M16 - UART console J10, populated, RX shorted to ground - 4 antennas 5 dBi, internal omni-directional plates - 4 LEDs power, 2G, 5G, wps - 1 button reset NOTE: all 4 gpio controlled LEDS are viewed through the same lightguide therefore, the power LED is off for default state MAC addresses: MAC address labeled as ETH Only one Vendor MAC address in flash at art 0x0 eth0 ETH :xb art 0x0 phy1 2.4G :xc --- phy0 5GHz :xd --- Serial Access:* the RX line on the board for UART is shorted to ground by resistor R176 therefore it must be removed to use the console but it is not necessary to remove to view boot log optionally, R175 can be replaced with a solder bridge short the resistors R175 and R176 are next to the UART RX pin at J10 Installation: Method 1: Firmware upgrade page: (if you cannot access the APs webpage) factory reset with the reset button connect ethernet to a computer OEM webpage at 192.168.20.253 username and password 'araknis' make a new password, login again... Navigate to 'File Management' page from left pane Click Browse and select the factory.bin image Upload and verify checksum Click Continue to confirm wait about 3 minutes Method 2: Serial to load Failsafe webpage: After connecting to serial console and rebooting... Interrupt uboot with any key pressed rapidly execute `run failsafe_boot` OR `bootm 0x9fd70000` wait a minute connect to ethernet and navigate to 192.168.20.253 Select the factory.bin image and upload wait about 3 minutes Return to OEM: Method 1: Serial to load Failsafe webpage (above) Method 2: delete a checksum from uboot-env this will make uboot load the failsafe image at next boot because it will fail the checksum verification of the image ssh into openwrt and run `fw_setenv rootfs_checksum 0` reboot, wait a minute connect to ethernet and navigate to 192.168.20.253 select OEM firmware image and click upgrade Method 3: backup mtd partitions before upgrade TFTP recovery: Requires serial console, reset button does nothing rename initramfs-kernel.bin to '0101A8C0.img' make available on TFTP server at 192.168.1.101 power board, interrupt boot with serial console execute `tftpboot` and `bootm 0x81000000` NOTE: TFTP may not be reliable due to bugged bootloader set MTU to 600 and try many times Format of OEM firmware image: The OEM software is built using SDKs from Senao which is based on a heavily modified version of Openwrt Kamikaze or Altitude Adjustment. One of the many modifications is sysupgrade being performed by a custom script. Images are verified through successful unpackaging, correct filenames and size requirements for both kernel and rootfs files, and that they start with the correct magic numbers (first 2 bytes) for the respective headers. Newer Senao software requires more checks but their script includes a way to skip them. The OEM upgrade script is at /etc/fwupgrade.sh OKLI kernel loader is required because the OEM software expects the kernel to be less than 1536k and the OEM upgrade procedure would otherwise overwrite part of the kernel when writing rootfs. Note on PLL-data cells: The default PLL register values will not work because of the external AR8035 switch between the SOC and the ethernet port. For QCA955x series, the PLL registers for eth0 and eth1 can be see in the DTSI as 0x28 and 0x48 respectively. Therefore the PLL registers can be read from uboot for each link speed after attempting tftpboot or another network action using that link speed with `md 0x18050028 1` and `md 0x18050048 1`. The clock delay required for RGMII can be applied at the PHY side, using the at803x driver `phy-mode` setting through the DTS. Therefore, the Ethernet Configuration registers for GMAC0 do not need the bits for RGMII delay on the MAC side. This is possible due to fixes in at803x driver since Linux 5.1 and 5.3 Signed-off-by: Michael Pratt <mcpratt@pm.me>	2022-03-13 19:54:58 +01:00
Michael Pratt	56716b578e	ath79: add support for Araknis AN-500-AP-I-AC FCC ID: 2AG6R-AN500APIAC Araknis AN-500-AP-I-AC is an indoor wireless access point with 1 Gb ethernet port, dual-band wireless, internal antenna plates, and 802.3at PoE+ this board is a Senao device: the hardware is equivalent to EnGenius EAP1200 the software is modified Senao SDK which is based on openwrt and uboot including image checksum verification at boot time, and a failsafe image that boots if checksum fails Specification: - QCA9557 SOC MIPS 74kc, 2.4 GHz WMAC, 2x2 - QCA9882 WLAN PCI card 168c:003c, 5 GHz, 2x2, 26dBm - AR8035-A PHY RGMII GbE with PoE+ IN - 40 MHz clock - 16 MB FLASH MX25L12845EMI-10G - 2x 64 MB RAM NT5TU32M16 - UART console J10, populated, RX shorted to ground - 4 antennas 5 dBi, internal omni-directional plates - 4 LEDs power, 2G, 5G, wps - 1 button reset NOTE: all 4 gpio controlled LEDS are viewed through the same lightguide therefore, the power LED is off for default state MAC addresses: MAC address labeled as ETH Only one Vendor MAC address in flash at art 0x0 eth0 ETH :e1 art 0x0 phy1 2.4G :e2 --- phy0 5GHz :e3 --- Serial Access:* the RX line on the board for UART is shorted to ground by resistor R176 therefore it must be removed to use the console but it is not necessary to remove to view boot log optionally, R175 can be replaced with a solder bridge short the resistors R175 and R176 are next to the UART RX pin at J10 Installation: Method 1: Firmware upgrade page: (if you cannot access the APs webpage) factory reset with the reset button connect ethernet to a computer OEM webpage at 192.168.20.253 username and password 'araknis' make a new password, login again... Navigate to 'File Management' page from left pane Click Browse and select the factory.bin image Upload and verify checksum Click Continue to confirm wait about 3 minutes Method 2: Serial to load Failsafe webpage: After connecting to serial console and rebooting... Interrupt uboot with any key pressed rapidly execute `run failsafe_boot` OR `bootm 0x9fd70000` wait a minute connect to ethernet and navigate to 192.168.20.253 Select the factory.bin image and upload wait about 3 minutes Return to OEM: Method 1: Serial to load Failsafe webpage (above) Method 2: delete a checksum from uboot-env this will make uboot load the failsafe image at next boot because it will fail the checksum verification of the image ssh into openwrt and run `fw_setenv rootfs_checksum 0` reboot, wait a minute connect to ethernet and navigate to 192.168.20.253 select OEM firmware image and click upgrade Method 3: backup mtd partitions before upgrade TFTP recovery: Requires serial console, reset button does nothing rename initramfs-kernel.bin to '0101A8C0.img' make available on TFTP server at 192.168.1.101 power board, interrupt boot with serial console execute `tftpboot` and `bootm 0x81000000` NOTE: TFTP may not be reliable due to bugged bootloader set MTU to 600 and try many times Format of OEM firmware image: The OEM software is built using SDKs from Senao which is based on a heavily modified version of Openwrt Kamikaze or Altitude Adjustment. One of the many modifications is sysupgrade being performed by a custom script. Images are verified through successful unpackaging, correct filenames and size requirements for both kernel and rootfs files, and that they start with the correct magic numbers (first 2 bytes) for the respective headers. Newer Senao software requires more checks but their script includes a way to skip them. The OEM upgrade script is at /etc/fwupgrade.sh OKLI kernel loader is required because the OEM software expects the kernel to be less than 1536k and the OEM upgrade procedure would otherwise overwrite part of the kernel when writing rootfs. Note on PLL-data cells: The default PLL register values will not work because of the external AR8035 switch between the SOC and the ethernet port. For QCA955x series, the PLL registers for eth0 and eth1 can be see in the DTSI as 0x28 and 0x48 respectively. Therefore the PLL registers can be read from uboot for each link speed after attempting tftpboot or another network action using that link speed with `md 0x18050028 1` and `md 0x18050048 1`. The clock delay required for RGMII can be applied at the PHY side, using the at803x driver `phy-mode` setting through the DTS. Therefore, the Ethernet Configuration registers for GMAC0 do not need the bits for RGMII delay on the MAC side. This is possible due to fixes in at803x driver since Linux 5.1 and 5.3 Signed-off-by: Michael Pratt <mcpratt@pm.me>	2022-03-13 19:54:57 +01:00
Michael Pratt	561f46bd02	ath79: add support for Araknis AN-300-AP-I-N FCC ID: U2M-AN300APIN Araknis AN-300-AP-I-N is an indoor wireless access point with 1 Gb ethernet port, dual-band wireless, internal antenna plates, and 802.3at PoE+ this board is a Senao device: the hardware is equivalent to EnGenius EWS310AP the software is modified Senao SDK which is based on openwrt and uboot including image checksum verification at boot time, and a failsafe image that boots if checksum fails Specification: - AR9344 SOC MIPS 74kc, 2.4 GHz WMAC, 2x2 - AR9382 WLAN PCI on-board 168c:0030, 5 GHz, 2x2 - AR8035-A PHY RGMII GbE with PoE+ IN - 40 MHz clock - 16 MB FLASH MX25L12845EMI-10G - 2x 64 MB RAM 1839ZFG V59C1512164QFJ25 - UART console J10, populated, RX shorted to ground - 4 antennas 5 dBi, internal omni-directional plates - 4 LEDs power, 2G, 5G, wps - 1 button reset NOTE: all 4 gpio controlled LEDS are viewed through the same lightguide therefore, the power LED is off for default state MAC addresses: MAC address labeled as ETH Only one Vendor MAC address in flash at art 0x0 eth0 ETH :7d art 0x0 phy1 2.4G :7e --- phy0 5GHz :7f --- Serial Access:* the RX line on the board for UART is shorted to ground by resistor R176 therefore it must be removed to use the console but it is not necessary to remove to view boot log optionally, R175 can be replaced with a solder bridge short the resistors R175 and R176 are next to the UART RX pin at J10 Installation: Method 1: Firmware upgrade page: (if you cannot access the APs webpage) factory reset with the reset button connect ethernet to a computer OEM webpage at 192.168.20.253 username and password 'araknis' make a new password, login again... Navigate to 'File Management' page from left pane Click Browse and select the factory.bin image Upload and verify checksum Click Continue to confirm wait about 3 minutes Method 2: Serial to load Failsafe webpage: After connecting to serial console and rebooting... Interrupt uboot with any key pressed rapidly execute `run failsafe_boot` OR `bootm 0x9fd70000` wait a minute connect to ethernet and navigate to 192.168.20.253 Select the factory.bin image and upload wait about 3 minutes Return to OEM: Method 1: Serial to load Failsafe webpage (above) Method 2: delete a checksum from uboot-env this will make uboot load the failsafe image at next boot because it will fail the checksum verification of the image ssh into openwrt and run `fw_setenv rootfs_checksum 0` reboot, wait a minute connect to ethernet and navigate to 192.168.20.253 select OEM firmware image and click upgrade Method 3: backup mtd partitions before upgrade TFTP recovery: Requires serial console, reset button does nothing rename initramfs-kernel.bin to '0101A8C0.img' make available on TFTP server at 192.168.1.101 power board, interrupt boot with serial console execute `tftpboot` and `bootm 0x81000000` NOTE: TFTP may not be reliable due to bugged bootloader set MTU to 600 and try many times Format of OEM firmware image: The OEM software is built using SDKs from Senao which is based on a heavily modified version of Openwrt Kamikaze or Altitude Adjustment. One of the many modifications is sysupgrade being performed by a custom script. Images are verified through successful unpackaging, correct filenames and size requirements for both kernel and rootfs files, and that they start with the correct magic numbers (first 2 bytes) for the respective headers. Newer Senao software requires more checks but their script includes a way to skip them. The OEM upgrade script is at /etc/fwupgrade.sh OKLI kernel loader is required because the OEM software expects the kernel to be less than 1536k and the OEM upgrade procedure would otherwise overwrite part of the kernel when writing rootfs. Note on PLL-data cells: The default PLL register values will not work because of the external AR8035 switch between the SOC and the ethernet port. For QCA955x series, the PLL registers for eth0 and eth1 can be see in the DTSI as 0x28 and 0x48 respectively. Therefore the PLL registers can be read from uboot for each link speed after attempting tftpboot or another network action using that link speed with `md 0x18050028 1` and `md 0x18050048 1`. The clock delay required for RGMII can be applied at the PHY side, using the at803x driver `phy-mode` setting through the DTS. Therefore, the Ethernet Configuration registers for GMAC0 do not need the bits for RGMII delay on the MAC side. This is possible due to fixes in at803x driver since Linux 5.1 and 5.3 Signed-off-by: Michael Pratt <mcpratt@pm.me>	2022-03-13 19:54:57 +01:00
Michael Pratt	07723492e9	ath79: improve factory.bin for some Senao devices Some boards with firmware made with Senao SDK based on Linux 3.3 have the following lines in the OEM upgrade script at /etc/fwupgrade.sh local append="" local CONF_TAR="/tmp/sysupgrade.tgz" [ -f "$CONF_TAR" ] && append="-j $CONF_TAR" and \# check FWINFO filename [ -z $(ls FWINFO* \| grep -i ${modelname}) ] && errcode="1" This addition also prevents needing to factory reset after flashing for some boards that also have these lines in the script \# Support downgrade but do default (Smart v2.x.x.x -> senaowrt v1.x.x.x) [ $(ls FWINFO* \| grep -i ${modelname} \| cut -d "-" -f4 \| cut -c 2) -lt 2 ] && append="" Signed-off-by: Michael Pratt <mcpratt@pm.me>	2022-03-13 19:54:57 +01:00
Thibaut VARÈNE	eb38af7881	ath79: add support for MikroTik RouterBOARD mAP lite The MikroTik RouterBOARD mAPL-2nd (sold as mAP Lite) is a small 2.4 GHz 802.11b/g/n PoE-capable AP. See https://mikrotik.com/product/RBmAPL-2nD for more info. Specifications: - SoC: Qualcomm Atheros QCA9533 - RAM: 64 MB - Storage: 16 MB NOR - Wireless: Atheros AR9531 (SoC) 802.11b/g/n 2x2:2, 1.5 dBi antenna - Ethernet: Atheros AR8229 (SoC), 1x 10/100 port, 802.3af/at PoE in - 4 user-controllable LEDs: · 1x power (green) · 1x user (green) · 1x lan (green) · 1x wlan (green) Flashing: TFTP boot initramfs image and then perform sysupgrade. Follow common MikroTik procedure as in https://openwrt.org/toh/mikrotik/common. Note: following `781d4bfb39` The network setup avoids using the integrated switch and connects the single Ethernet port directly. This way, link speed (10/100 Mbps) is properly reported by eth0. Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>	2022-03-08 18:33:42 +01:00
Piotr Dymacz	9c335accfe	ath79: add support for TP-Link Archer A9 v6 TP-Link Archer A9 v6 (FCCID: TE7A9V6) is an AC1900 Wave-2 gigabit home router based on a combination of Qualcomm QCN5502 (most likely a 4x4:4 version of the QCA9563 WiSOC), QCA9984 and QCA8337N. The vendor's firmware content reveals that the same device might be available on the US market under name 'Archer C90 v6'. Due to lack of access to such hardware, support introduced in this commit was tested only on the EU version (sold under 'Archer A9 v6' name). Based on the information on the PL version of the vendor website, this device has been already phased out and is no longer available. Specifications: - Qualcomm QCN5502 (775 MHz) - 128 MB of RAM (DDR2) - 16 MB of flash (SPI NOR) - 5x Gbps Ethernet (Qualcomm QCA8337N over SGMII) - Wi-Fi: - 802.11b/g/n on 2.4 GHz: Qualcomm QCN5502* in 4x4:4 mode - 802.11a/n/ac on 5 GHz: Qualcomm QCA9984 in 3x3:3 mode - 3x non-detachable, dual-band external antennas (~3.5 dBi for 5 GHz, ~2.2 dBi for 2.4 GHz, IPEX/U.FL connectors) - 1x internal PCB antenna for 2.4 GHz (~1.8 dBi) - 1x USB 2.0 Type-A - 11x LED (4x connected to QCA8337N, 7x connected to QCN5502) - 2x button (reset, WPS) - UART (4-pin, 2.54 mm pitch) header on PCB (not populated) - 1x mechanical power switch - 1x DC jack (12 V) *) unsupported due to missing support for QCN550x in ath9k UART system serial console notice: The RX signal of the main SOC's UART on this device is shared with the WPS button's GPIO. The first-stage U-Boot by default disables the RX, resulting in a non-functional UART input. If you press and keep 'ENTER' on the serial console during early boot-up, the first-stage U-Boot will enable RX input. Vendor firmware allows password-less access to the system over serial. Flash instruction (vendor GUI): 1. It is recommended to first upgrade vendor firmware to the latest version (1.1.1 Build 20210315 rel.40637 at the time of writing). 2. Use the 'factory' image directly in the vendor's GUI. Flash instruction (TFTP based recovery in second-stage U-Boot): 1. Rename 'factory' image to 'ArcherA9v6_tp_recovery.bin' 2. Setup a TFTP server on your PC with IP 192.168.0.66/24. 3. Press and hold the reset button for ~5 sec while turning on power. 4. The device will download image, flash it and reboot. Flash instruction (web based recovery in first-stage U-Boot): 1. Use 'CTRL+C' during power-up to enable CLI in first-stage U-Boot. 2. Connect a PC with IP set to 192.168.0.1 to one of the LAN ports. 3. Issue 'httpd' command and visit http://192.168.0.1 in browser. 4. Use the 'factory' image. If you would like to restore vendor's firmware, follow one of the recovery methods described above. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>	2022-02-27 16:54:55 +01:00
Piotr Dymacz	131671bc54	ath79: add support for ALFA Network Tube-2HQ ALFA Network Tube-2HQ is a successor of the Tube-2H/P series (EOL) which was based on the Atheros AR9331. The new version uses Qualcomm QCA9531. Specifications: - Qualcomm/Atheros QCA9531 v2 - 650/400/200 MHz (CPU/DDR/AHB) - 64 or 128 MB of RAM (DDR2) - 16+ MB of flash (SPI NOR) - 1x 10/100 Mbps Ethernet with passive PoE input (24 V) (802.3at/af PoE support with optional module) - 1T1R 2.4 GHz Wi-Fi with external PA (SE2623L, up to 27 dBm) and LNA - 1x Type-N (male) antenna connector - 6x LED (5x driven by GPIO) - 1x button (reset) - external h/w watchdog (EM6324QYSP5B, enabled by default) - UART (4-pin, 2.00 mm pitch) header on PCB Flash instruction: You can use sysupgrade image directly in vendor firmware which is based on LEDE/OpenWrt. Alternatively, you can use web recovery mode in U-Boot: 1. Configure PC with static IP 192.168.1.2/24. 2. Connect PC with one of RJ45 ports, press the reset button, power up device, wait for first blink of all LEDs (indicates network setup), then keep button for 3 following blinks and release it. 3. Open 192.168.1.1 address in your browser and upload sysupgrade image. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>	2022-02-27 16:54:54 +01:00
Lech Perczak	7ac8da0060	ath79: support ZTE MF286A/R ZTE MF286A and MF286R are indoor LTE category 6/7 CPE router with simultaneous dual-band 802.11ac plus 802.11n Wi-Fi radios and quad-port gigabit Ethernet switch, FXS and external USB 2.0 port. Hardware highlights: - CPU: QCA9563 SoC at 775MHz, - RAM: 128MB DDR2, - NOR Flash: MX25L1606E 2MB SPI Flash, for U-boot only, - NAND Flash: W25N01GV 128MB SPI NAND-Flash, for all other data, - Wi-Fi 5GHz: QCA9886 2x2 MIMO 802.11ac Wave2 radio, - WI-Fi 2.4GHz: QCA9563 3x3 MIMO 802.11n radio, - Switch: QCA8337v2 4-port gigabit Ethernet, with single SGMII CPU port, - WWAN: [MF286A] MDM9230-based category 6 internal LTE modem [MF286R] PXA1826-based category 7 internal LTE modem in extended mini-PCIE form factor, with 3 internal antennas and 2 external antenna connections, single mini-SIM slot. - FXS: one external ATA port (handled entirely by modem part) with two physical connections in parallel, - USB: Single external USB 2.0 port, - Switches: power switch, WPS, Wi-Fi and reset buttons, - LEDs: Wi-Fi, Test (internal). Rest of LEDs (Phone, WWAN, Battery, Signal state) handled entirely by modem. 4 link status LEDs handled by the switch on the backside. - Battery: 3Ah 1-cell Li-Ion replaceable battery, with charging and monitoring handled by modem. - Label MAC device: eth0 The device shares many components with previous model, MF286, differing mostly by a Wave2 5GHz radio, flash layout and internal LED color. In case of MF286A, the modem is the same as in MF286. MF286R uses a different modem based on Marvell PXA1826 chip. Internal modem of MF286A is supported via uqmi, MF286R modem isn't fully supported, but it is expected to use comgt-ncm for connection, as it uses standard 3GPP AT commands for connection establishment. Console connection: connector X2 is the console port, with the following pinout, starting from pin 1, which is the topmost pin when the board is upright: - VCC (3.3V). Do not use unless you need to source power for the converer from it. - TX - RX - GND Default port configuration in U-boot as well as in stock firmware is 115200-8-N-1. Installation: Due to different flash layout from stock firmware, sysupgrade from within stock firmware is impossible, despite it's based on QSDK which itself is based on OpenWrt. STEP 0: Stock firmware update: As installing OpenWrt cuts you off from official firmware updates for the modem part, it is recommended to update the stock firmware to latest version before installation, to have built-in modem at the latest firmware version. STEP 1: gaining root shell: Method 1: This works if busybox has telnetd compiled in the binary. If this does not work, try method 2. Using well-known exploit to start telnetd on your router - works only if Busybox on stock firmware has telnetd included: - Open stock firmware web interface - Navigate to "URL filtering" section by going to "Advanced settings", then "Firewall" and finally "URL filter". - Add an entry ending with "&&telnetd&&", for example "http://hostname/&&telnetd&&". - telnetd will immediately listen on port 4719. - After connecting to telnetd use "admin/admin" as credentials. Method 2: This works if busybox does not have telnetd compiled in. Notably, this is the case in DNA.fi firmware. If this does not work, try method 3. - Set IP of your computer to 192.168.0.22. (or appropriate subnet if changed) - Have a TFTP server running at that address - Download MIPS build of busybox including telnetd, for example from: https://busybox.net/downloads/binaries/1.21.1/busybox-mips and put it in it's root directory. Rename it as "telnetd". - As previously, login to router's web UI and navigate to "URL filtering" - Using "Inspect" feature, extend "maxlength" property of the input field named "addURLFilter", so it looks like this: <input type="text" name="addURLFilter" id="addURLFilter" maxlength="332" class="required form-control"> - Stay on the page - do not navigate anywhere - Enter "http://aa&zte_debug.sh 192.168.0.22 telnetd" as a filter. - Save the settings. This will download the telnetd binary over tftp and execute it. You should be able to log in at port 23, using "admin/admin" as credentials. Method 3: If the above doesn't work, use the serial console - it exposes root shell directly without need for login. Some stock firmwares, notably one from finnish DNA operator lack telnetd in their builds. STEP 2: Backing up original software: As the stock firmware may be customized by the carrier and is not officially available in the Internet, IT IS IMPERATIVE to back up the stock firmware, if you ever plan to returning to stock firmware. It is highly recommended to perform backup using both methods, to avoid hassle of reassembling firmware images in future, if a restore is needed. Method 1: after booting OpenWrt initramfs image via TFTP: PLEASE NOTE: YOU CANNOT DO THIS IF USING INTERMEDIATE FIRMWARE FOR INSTALLATION. - Dump stock firmware located on stock kernel and ubi partitions: ssh root@192.168.1.1: cat /dev/mtd4 > mtd4_kernel.bin ssh root@192.168.1.1: cat /dev/mtd9 > mtd9_ubi.bin And keep them in a safe place, should a restore be needed in future. Method 2: using stock firmware: - Connect an external USB drive formatted with FAT or ext4 to the USB port. - The drive will be auto-mounted to /var/usb_disk - Check the flash layout of the device: cat /proc/mtd It should show the following: mtd0: 000a0000 00010000 "u-boot" mtd1: 00020000 00010000 "u-boot-env" mtd2: 00140000 00010000 "reserved1" mtd3: 000a0000 00020000 "fota-flag" mtd4: 00080000 00020000 "art" mtd5: 00080000 00020000 "mac" mtd6: 000c0000 00020000 "reserved2" mtd7: 00400000 00020000 "cfg-param" mtd8: 00400000 00020000 "log" mtd9: 000a0000 00020000 "oops" mtd10: 00500000 00020000 "reserved3" mtd11: 00800000 00020000 "web" mtd12: 00300000 00020000 "kernel" mtd13: 01a00000 00020000 "rootfs" mtd14: 01900000 00020000 "data" mtd15: 03200000 00020000 "fota" mtd16: 01d00000 00020000 "firmware" Differences might indicate that this is NOT a MF286A device but one of other variants. - Copy over all MTD partitions, for example by executing the following: for i in 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15; do cat /dev/mtd$i > \ /var/usb_disk/mtd$i; done "Firmware" partition can be skipped, it is a concatenation of "kernel" and "rootfs". - If the count of MTD partitions is different, this might indicate that this is not a MF286A device, but one of its other variants. - (optionally) rename the files according to MTD partition names from /proc/mtd - Unmount the filesystem: umount /var/usb_disk; sync and then remove the drive. - Store the files in safe place if you ever plan to return to stock firmware. This is especially important, because stock firmware for this device is not available officially, and is usually customized by the mobile providers. STEP 3: Booting initramfs image: Method 1: using serial console (RECOMMENDED): - Have TFTP server running, exposing the OpenWrt initramfs image, and set your computer's IP address as 192.168.0.22. This is the default expected by U-boot. You may wish to change that, and alter later commands accordingly. - Connect the serial console if you haven't done so already, - Interrupt boot sequence by pressing any key in U-boot when prompted - Use the following commands to boot OpenWrt initramfs through TFTP: setenv serverip 192.168.0.22 setenv ipaddr 192.168.0.1 tftpboot 0x81000000 openwrt-ath79-nand-zte_mf286a-initramfs-kernel.bin bootm 0x81000000 (Replace server IP and router IP as needed). There is no emergency TFTP boot sequence triggered by buttons, contrary to MF283+. - When OpenWrt initramfs finishes booting, proceed to actual installation. Method 2: using initramfs image as temporary boot kernel This exploits the fact, that kernel and rootfs MTD devices are consecutive on NAND flash, so from within stock image, an initramfs can be written to this area and booted by U-boot on next reboot, because it uses "nboot" command which isn't limited by kernel partition size. - Download the initramfs-kernel.bin image - After backing up the previous MTD contents, write the images to the "firmware" MTD device, which conveniently concatenates "kernel" and "rootfs" partitions that can fit the initramfs image: nandwrite -p /dev/<firmware-mtd> \ /var/usb_disk/openwrt-ath79-zte_mf286a-initramfs-kernel.bin - If write is OK, reboot the device, it will reboot to OpenWrt initramfs: reboot -f - After rebooting, SSH into the device and use sysupgrade to perform proper installation. Method 3: using built-in TFTP recovery (LAST RESORT): - With that method, ensure you have complete backup of system's NAND flash first. It involves deliberately erasing the kernel. - Download "-initramfs-kernel.bin" image for the device. - Prepare the recovery image by prepending 8MB of zeroes to the image, and name it root_uImage: dd if=/dev/zero of=padding.bin bs=8M count=1 cat padding.bin openwrt-ath79-nand-zte_mf286a-initramfs-kernel.bin > root_uImage - Set up a TFTP server at 192.0.0.1/8. Router will use random address from that range. - Put the previously generated "root_uImage" into TFTP server root directory. - Deliberately erase "kernel" partition" using stock firmware after taking backup. THIS IS POINT OF NO RETURN. - Restart the device. U-boot will attempt flashing the recovery initramfs image, which will let you perform actual installation using sysupgrade. This might take a considerable time, sometimes the router doesn't establish Ethernet link properly right after booting. Be patient. - After U-boot finishes flashing, the LEDs of switch ports will all light up. At this moment, perform power-on reset, and wait for OpenWrt initramfs to finish booting. Then proceed to actual installation. STEP 4: Actual installation: - Set your computer IP to 192.168.1.22/24 - scp the sysupgrade image to the device: scp openwrt-ath79-nand-zte_mf286a-squashfs-sysupgrade.bin \ root@192.168.1.1:/tmp/ - ssh into the device and execute sysupgrade: sysupgrade -n /tmp/openwrt-ath79-nand-zte_mf286a-squashfs-sysupgrade.bin - Wait for router to reboot to full OpenWrt. STEP 5: WAN connection establishment Since the router is equipped with LTE modem as its main WAN interface, it might be useful to connect to the Internet right away after installation. To do so, please put the following entries in /etc/config/network, replacing the specific configuration entries with one needed for your ISP: config interface 'wan' option proto 'qmi' option device '/dev/cdc-wdm0' option auth '<auth>' # As required, usually 'none' option pincode '<pin>' # If required by SIM option apn '<apn>' # As required by ISP option pdptype '<pdp>' # Typically 'ipv4', or 'ipv4v6' or 'ipv6' For example, the following works for most polish ISPs config interface 'wan' option proto 'qmi' option device '/dev/cdc-wdm0' option auth 'none' option apn 'internet' option pdptype 'ipv4' The required minimum is: config interface 'wan' option proto 'qmi' option device '/dev/cdc-wdm0' In this case, the modem will use last configured APN from stock firmware - this should work out of the box, unless your SIM requires PIN which can't be switched off. If you have build with LuCI, installing luci-proto-qmi helps with this task. Restoring the stock firmware: Preparation: If you took your backup using stock firmware, you will need to reassemble the partitions into images to be restored onto the flash. The layout might differ from ISP to ISP, this example is based on generic stock firmware The only partitions you really care about are "web", "kernel", and "rootfs". These are required to restore the stock firmware through factory TFTP recovery. Because kernel partition was enlarged, compared to stock firmware, the kernel and rootfs MTDs don't align anymore, and you need to carve out required data if you only have backup from stock FW: - Prepare kernel image cat mtd12_kernel.bin mtd13_rootfs.bin > owrt_kernel.bin truncate -s 4M owrt_kernel_restore.bin - Cut off first 1MB from rootfs dd if=mtd13_rootfs.bin of=owrt_rootfs.bin bs=1M skip=1 - Prepare image to write to "ubi" meta-partition: cat mtd6_reserved2.bi mtd7_cfg-param.bin mtd8_log.bin mtd9_oops.bin \ mtd10_reserved3.bin mtd11_web.bin owrt_rootfs.bin > \ owrt_ubi_ubi_restore.bin You can skip the "fota" partition altogether, it is used only for stock firmware update purposes and can be overwritten safely anyway. The same is true for "data" partition which on my device was found to be unused at all. Restoring mtd5_cfg-param.bin will restore the stock firmware configuration you had before. Method 1: Using initramfs: This method is recmmended if you took your backup from within OpenWrt initramfs, as the reassembly is not needed. - Boot to initramfs as in step 3: - Completely detach ubi0 partition using ubidetach /dev/ubi0_0 - Look up the kernel and ubi partitions in /proc/mtd - Copy over the stock kernel image using scp to /tmp - Erase kernel and restore stock kernel: (scp mtd4_kernel.bin root@192.168.1.1:/tmp/) mtd write <kernel_mtd> mtd4_kernel.bin rm mtd4_kernel.bin - Copy over the stock partition backups one-by-one using scp to /tmp, and restore them individually. Otherwise you might run out of space in tmpfs: (scp mtd3_ubiconcat0.bin root@192.168.1.1:/tmp/) mtd write <ubiconcat0_mtd> mtd3_ubiconcat0.bin rm mtd3_ubiconcat0.bin (scp mtd5_ubiconcat1.bin root@192.168.1.1:/tmp/) mtd write <ubiconcat1_mtd> mtd5_ubiconcat1.bin rm mtd5_ubiconcat1.bin - If the write was correct, force a device reboot with reboot -f Method 2: Using live OpenWrt system (NOT RECOMMENDED): - Prepare a USB flash drive contatining MTD backup files - Ensure you have kmod-usb-storage and filesystem driver installed for your drive - Mount your flash drive mkdir /tmp/usb mount /dev/sda1 /tmp/usb - Remount your UBI volume at /overlay to R/O mount -o remount,ro /overlay - Write back the kernel and ubi partitions from USB drive cd /tmp/usb mtd write mtd4_kernel.bin /dev/<kernel_mtd> mtd write mtd9_ubi.bin /dev/<kernel_ubi> - If everything went well, force a device reboot with reboot -f Last image may be truncated a bit due to lack of space in RAM, but this will happen over "fota" MTD partition which may be safely erased after reboot anyway. Method 3: using built-in TFTP recovery: This method is recommended if you took backups using stock firmware. - Assemble a recovery rootfs image from backup of stock partitions by concatenating "web", "kernel", "rootfs" images dumped from the device, as "root_uImage" - Use it in place of "root_uImage" recovery initramfs image as in the TFTP pre-installation method. Quirks and known issuesa - It was observed, that CH340-based USB-UART converters output garbage during U-boot phase of system boot. At least CP2102 is known to work properly. - Kernel partition size is increased to 4MB compared to stock 3MB, to accomodate future kernel updates - at this moment OpenWrt 5.10 kernel image is at 2.5MB which is dangerously close to the limit. This has no effect on booting the system - but keep that in mind when reassembling an image to restore stock firmware. - uqmi seems to be unable to change APN manually, so please use the one you used before in stock firmware first. If you need to change it, please use protocok '3g' to establish connection once, or use the following command to change APN (and optionally IP type) manually: echo -ne 'AT+CGDCONT=1,"IP","<apn>' > /dev/ttyUSB0 - The only usable LED as a "system LED" is the blue debug LED hidden inside the case. All other LEDs are controlled by modem, on which the router part has some influence only on Wi-Fi LED. - Wi-Fi LED currently doesn't work while under OpenWrt, despite having correct GPIO mapping. All other LEDs are controlled by modem, including this one in stock firmware. GPIO19, mapped there only acts as a gate, while the actual signal source seems to be 5GHz Wi-Fi radio, however it seems it is not the LED exposed by ath10k as ath10k-phy0. - GPIO5 used for modem reset is a suicide switch, causing a hardware reset of whole board, not only the modem. It is attached to gpio-restart driver, to restart the modem on reboot as well, to ensure QMI connectivity after reboot, which tends to fail otherwise. - Modem, as in MF283+, exposes root shell over ADB - while not needed for OpenWrt operation at all - have fun lurking around. The same modem module is used as in older MF286. Signed-off-by: Lech Perczak <lech.perczak@gmail.com>	2022-02-26 17:46:10 +01:00
Alex Henrie	fe1ecf1fcb	ath79: add Zyxel EMG2926-Q10A The Zyxel EMG2926-Q10A is 99% the Zyxel NBG6716, but the bootloader expects a different product name when flashing over TFTP. Also, the EMG2926-Q10A always has 128 MiB of NAND flash whereas the NBG6716 reportedly can have either 128 MiB or 256 MiB. Signed-off-by: Alex Henrie <alexhenrie24@gmail.com>	2022-02-26 13:36:30 +01:00
Piotr Dymacz	aae7af4219	ath79: image: use 'kmod-usb-chipidea2' for AR933x devices AR933x based devices should include 'kmod-usb-chipidea2' for USB support. Fixes: #9243. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>	2022-02-21 22:22:30 +01:00
Piotr Dymacz	034531db73	ath79: image: drop 'BOARDNAME' from devices recipes The 'BOARDNAME' variable is part of target configuration and shouldn't be part of a device's image recipe. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>	2022-02-21 19:16:30 +01:00
Daniel González Cabanelas	73ea763c0d	ath79: Add support for Ubiquiti NanoBeam AC Gen1 XC The Ubiquiti NanoBeam AC Gen1 XC (NBE-5AC-19) is an outdoor 802.11ac CPE with a waterproof casing (ultrasonically welded) and bulb shaped. Hardware: - SoC: Qualcomm Atheros QCA9558 - RAM: 128 MB DDR2 - Flash: 16 MB SPI NOR - Ethernet: 1x GbE, AR8033 phy connected via SGMII - PSU: 24 Vdc passive PoE - WiFi 5 GHz: Qualcomm Atheros QCA988X - Buttons: 1x reset - LEDs: 1x power, 1x Ethernet, 4x RSSI, all blue - Internal antenna: 19 dBi planar Installation from stock airOS firmware: - Follow instructions for XC-type Ubiquiti devices on OpenWrt wiki at https://openwrt.org/toh/ubiquiti/common Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>	2022-02-19 13:10:01 +01:00
Mauri Sandberg	b99aee5080	ath79: use gpio-cascade for Buffalo WZR-HP-G300NH Switch to a generic GPIO cascade driver. Signed-off-by: Mauri Sandberg <maukka@ext.kapsi.fi> Signed-off-by: Petr Štetiar <ynezz@true.cz> [missing commit description]	2022-02-19 13:10:01 +01:00
Jakob Riepler	e0683839b8	ath79: add support for Mikrotik LHG 5 The MikroTik LHG 5 series (product codes RBLHG-5nD, RBLHG-5HPnD and RBLHG-5HPnD-XL) devices are an outdoor 5GHz CPE with a 24.5dBi or 27dBi integrated antenna built around the Atheros AR9344 SoC. It is very similar to the SXT Lite5 series which this patch is based upon. Specifications: - SoC: Atheros AR9344 - RAM: 64 MB - Storage: 16 MB SPI NOR - Wireless: Atheros AR9340 (SoC) 802.11a/n 2x2:2 - Ethernet: Atheros AR8229 switch (SoC), 1x 10/100 port, 8-32 Vdc PoE in - 8 user-controllable LEDs: - 1x power (blue) - 1x user (white) - 1x ethernet (green) - 5x rssi (green) See https://mikrotik.com/product/RBLHG-5nD for more details. Notes: The device was already supported in the ar71xx target. Flashing: TFTP boot initramfs image and then perform a sysupgrade. Follow common MikroTik procedure as in https://openwrt.org/toh/mikrotik/common. Signed-off-by: Jakob Riepler <jakob+openwrt@chaosfield.at>	2022-02-07 00:03:27 +01:00
Wenli Looi	c32008a37b	ath79: add partial support for Netgear EX7300v2 Hardware -------- SoC: QCN5502 Flash: 16 MiB RAM: 128 MiB Ethernet: 1 gigabit port Wireless No1: QCN5502 on-chip 2.4GHz 4x4 Wireless No2: QCA9984 pcie 5GHz 4x4 USB: none Installation ------------ Flash the factory image using the stock web interface or TFTP the factory image to the bootloader. What works ---------- - LEDs - Ethernet port - 5GHz wifi (QCA9984 pcie) What doesn't work ----------------- - 2.4GHz wifi (QCN5502 on-chip) (I was not able to make this work, probably because ath9k requires some changes to support QCN5502.) Signed-off-by: Wenli Looi <wlooi@ucalgary.ca>	2022-02-07 00:03:27 +01:00
Saiful Islam	43ec6d64bb	ath79: add support for TP-Link TL-WR841HP v2 Specifications: - AR9344 SoC, 8 MB nor flash, 64 MB DDR2 RAM - 2x2 9dBi antenna, wifi 2.4Ghz 300Mbps - 4x Ethernet LAN 10/100, 1x Ethernet WAN 10/100 - 1x WAN, 4x LAN, Wifi, PWR, WPS, SYSTEM Leds - Reset/WPS button - Serial UART at J4 onboard: 3.3v GND RX TX, 1152008N1 MAC addresses as verified by OEM firmware: vendor OpenWrt address LAN eth0 label WAN eth1 label + 1 WLAN phy0 label The label MAC address was found in u-boot 0x1fc00. Installation: To install openwrt, - set the device's SSID to each of the following lines, making sure to include the backticks. - set the ssid and click save between each line. `echo "httpd -k"> /tmp/s` `echo "sleep 10">> /tmp/s` `echo "httpd -r&">> /tmp/s` `echo "sleep 10">> /tmp/s` `echo "httpd -k">> /tmp/s` `echo "sleep 10">> /tmp/s` `echo "httpd -f">> /tmp/s` `sh /tmp/s` - Now, wait 60 sec. - After the reboot sequence, the router may have fallen back to its default IP address with the default credentials (admin:admin). - Log in to the web interface and go the the firmware upload page. Select "openwrt-ath79-generic-tplink_tl-wr841hp-v2-squashfs-factory.bin" and you're done : the system now accepts the openwrt. Forum support topic: https://forum.openwrt.org/t/support-for-tplink-tl-wr841hp-v2/69445/ Signed-off-by: Saiful Islam <si87868@gmail.com>	2022-02-07 00:03:27 +01:00
Lech Perczak	8c78a13bfc	ath79: support ZTE MF286 ZTE MF286 is an indoor LTE category 6 CPE router with simultaneous dual-band 802.11ac plus 802.11n Wi-Fi radios and quad-port gigabit Ethernet switch, FXS and external USB 2.0 port. Hardware highlights: - CPU: QCA9563 SoC at 775MHz, - RAM: 128MB DDR2, - NOR Flash: MX25L1606E 2MB SPI Flash, for U-boot only, - NAND Flash: GD5F1G04UBYIG 128MB SPI NAND-Flash, for all other data, - Wi-Fi 5GHz: QCA9882 2x2 MIMO 802.11ac radio, - WI-Fi 2.4GHz: QCA9563 3x3 MIMO 802.11n radio, - Switch: QCA8337v2 4-port gigabit Ethernet, with single SGMII CPU port, - WWAN: MDM9230-based category 6 internal LTE modem in extended mini-PCIE form factor, with 3 internal antennas and 2 external antenna connections, single mini-SIM slot. Modem model identified as MF270, - FXS: one external ATA port (handled entirely by modem part) with two physical connections in parallel, - USB: Single external USB 2.0 port, - Switches: power switch, WPS, Wi-Fi and reset buttons, - LEDs: Wi-Fi, Test (internal). Rest of LEDs (Phone, WWAN, Battery, Signal state) handled entirely by modem. 4 link status LEDs handled by the switch on the backside. - Battery: 3Ah 1-cell Li-Ion replaceable battery, with charging and monitoring handled by modem. - Label MAC device: eth0 Console connection: connector X2 is the console port, with the following pinout, starting from pin 1, which is the topmost pin when the board is upright: - VCC (3.3V). Do not use unless you need to source power for the converer from it. - TX - RX - GND Default port configuration in U-boot as well as in stock firmware is 115200-8-N-1. Installation: Due to different flash layout from stock firmware, sysupgrade from within stock firmware is impossible, despite it's based on QSDK which itself is based on OpenWrt. STEP 0: Stock firmware update: As installing OpenWrt cuts you off from official firmware updates for the modem part, it is recommended to update the stock firmware to latest version before installation, to have built-in modem at the latest firmware version. STEP 1: gaining root shell: Method 1: This works if busybox has telnetd compiled in the binary. If this does not work, try method 2. Using well-known exploit to start telnetd on your router - works only if Busybox on stock firmware has telnetd included: - Open stock firmware web interface - Navigate to "URL filtering" section by going to "Advanced settings", then "Firewall" and finally "URL filter". - Add an entry ending with "&&telnetd&&", for example "http://hostname/&&telnetd&&". - telnetd will immediately listen on port 4719. - After connecting to telnetd use "admin/admin" as credentials. Method 2: This works if busybox does not have telnetd compiled in. Notably, this is the case in DNA.fi firmware. If this does not work, try method 3. - Set IP of your computer to 192.168.1.22. - Have a TFTP server running at that address - Download MIPS build of busybox including telnetd, for example from: https://busybox.net/downloads/binaries/1.21.1/busybox-mips and put it in it's root directory. Rename it as "telnetd". - As previously, login to router's web UI and navigate to "URL filtering" - Using "Inspect" feature, extend "maxlength" property of the input field named "addURLFilter", so it looks like this: <input type="text" name="addURLFilter" id="addURLFilter" maxlength="332" class="required form-control"> - Stay on the page - do not navigate anywhere - Enter "http://aa&zte_debug.sh 192.168.1.22 telnetd" as a filter. - Save the settings. This will download the telnetd binary over tftp and execute it. You should be able to log in at port 23, using "admin/admin" as credentials. Method 3: If the above doesn't work, use the serial console - it exposes root shell directly without need for login. Some stock firmwares, notably one from finnish DNA operator lack telnetd in their builds. STEP 2: Backing up original software: As the stock firmware may be customized by the carrier and is not officially available in the Internet, IT IS IMPERATIVE to back up the stock firmware, if you ever plan to returning to stock firmware. Method 1: after booting OpenWrt initramfs image via TFTP: PLEASE NOTE: YOU CANNOT DO THIS IF USING INTERMEDIATE FIRMWARE FOR INSTALLATION. - Dump stock firmware located on stock kernel and ubi partitions: ssh root@192.168.1.1: cat /dev/mtd4 > mtd4_kernel.bin ssh root@192.168.1.1: cat /dev/mtd8 > mtd8_ubi.bin And keep them in a safe place, should a restore be needed in future. Method 2: using stock firmware: - Connect an external USB drive formatted with FAT or ext4 to the USB port. - The drive will be auto-mounted to /var/usb_disk - Check the flash layout of the device: cat /proc/mtd It should show the following: mtd0: 00080000 00010000 "uboot" mtd1: 00020000 00010000 "uboot-env" mtd2: 00140000 00020000 "fota-flag" mtd3: 00140000 00020000 "caldata" mtd4: 00140000 00020000 "mac" mtd5: 00600000 00020000 "cfg-param" mtd6: 00140000 00020000 "oops" mtd7: 00800000 00020000 "web" mtd8: 00300000 00020000 "kernel" mtd9: 01f00000 00020000 "rootfs" mtd10: 01900000 00020000 "data" mtd11: 03200000 00020000 "fota" Differences might indicate that this is NOT a vanilla MF286 device but one of its later derivatives. - Copy over all MTD partitions, for example by executing the following: for i in 0 1 2 3 4 5 6 7 8 9 10 11; do cat /dev/mtd$i > \ /var/usb_disk/mtd$i; done - If the count of MTD partitions is different, this might indicate that this is not a standard MF286 device, but one of its later derivatives. - (optionally) rename the files according to MTD partition names from /proc/mtd - Unmount the filesystem: umount /var/usb_disk; sync and then remove the drive. - Store the files in safe place if you ever plan to return to stock firmware. This is especially important, because stock firmware for this device is not available officially, and is usually customized by the mobile providers. STEP 3: Booting initramfs image: Method 1: using serial console (RECOMMENDED): - Have TFTP server running, exposing the OpenWrt initramfs image, and set your computer's IP address as 192.168.1.22. This is the default expected by U-boot. You may wish to change that, and alter later commands accordingly. - Connect the serial console if you haven't done so already, - Interrupt boot sequence by pressing any key in U-boot when prompted - Use the following commands to boot OpenWrt initramfs through TFTP: setenv serverip 192.168.1.22 setenv ipaddr 192.168.1.1 tftpboot 0x81000000 openwrt-ath79-nand-zte_mf286-initramfs-kernel.bin bootm 0x81000000 (Replace server IP and router IP as needed). There is no emergency TFTP boot sequence triggered by buttons, contrary to MF283+. - When OpenWrt initramfs finishes booting, proceed to actual installation. Method 2: using initramfs image as temporary boot kernel This exploits the fact, that kernel and rootfs MTD devices are consecutive on NAND flash, so from within stock image, an initramfs can be written to this area and booted by U-boot on next reboot, because it uses "nboot" command which isn't limited by kernel partition size. - Download the initramfs-kernel.bin image - Split the image into two parts on 3MB partition size boundary, which is the size of kernel partition. Pad the output of second file to eraseblock size: dd if=openwrt-ath79-nand-zte_mf286-initramfs-kernel.bin \ bs=128k count=24 \ of=openwrt-ath79-zte_mf286-intermediate-kernel.bin dd if=openwrt-ath79-nand-zte_mf286-initramfs-kernel.bin \ bs=128k skip=24 conv=sync \ of=openwrt-ath79-zte_mf286-intermediate-rootfs.bin - Copy over /usr/bin/flash_eraseall and /usr/bin/nandwrite utilities to /tmp. This is CRITICAL for installation, as erasing rootfs will cut you off from those tools on flash! - After backing up the previous MTD contents, write the images to the respective MTD devices: /tmp/flash_eraseall /dev/<kernel-mtd> /tmp/nandwrite /dev/<kernel-mtd> \ /var/usb_disk/openwrt-ath79-zte_mf286-intermediate-kernel.bin /tmp/flash_eraseall /dev/<kernel-mtd> /tmp/nandwrite /dev/<rootfs-mtd> \ /var/usb_disk/openwrt-ath79-zte_mf286-intermediate-rootfs.bin - Ensure that no bad blocks were present on the devices while writing. If they were present, you may need to vary the split between kernel and rootfs parts, so U-boot reads a valid uImage after skipping the bad blocks. If it fails, you will be left with method 3 (below). - If write is OK, reboot the device, it will reboot to OpenWrt initramfs: reboot -f - After rebooting, SSH into the device and use sysupgrade to perform proper installation. Method 3: using built-in TFTP recovery (LAST RESORT): - With that method, ensure you have complete backup of system's NAND flash first. It involves deliberately erasing the kernel. - Download "-initramfs-kernel.bin" image for the device. - Prepare the recovery image by prepending 8MB of zeroes to the image, and name it root_uImage: dd if=/dev/zero of=padding.bin bs=8M count=1 cat padding.bin openwrt-ath79-nand-zte_mf286-initramfs-kernel.bin > root_uImage - Set up a TFTP server at 192.0.0.1/8. Router will use random address from that range. - Put the previously generated "root_uImage" into TFTP server root directory. - Deliberately erase "kernel" partition" using stock firmware after taking backup. THIS IS POINT OF NO RETURN. - Restart the device. U-boot will attempt flashing the recovery initramfs image, which will let you perform actual installation using sysupgrade. This might take a considerable time, sometimes the router doesn't establish Ethernet link properly right after booting. Be patient. - After U-boot finishes flashing, the LEDs of switch ports will all light up. At this moment, perform power-on reset, and wait for OpenWrt initramfs to finish booting. Then proceed to actual installation. STEP 4: Actual installation: - scp the sysupgrade image to the device: scp openwrt-ath79-nand-zte_mf286-squashfs-sysupgrade.bin \ root@192.168.1.1:/tmp/ - ssh into the device and execute sysupgrade: sysupgrade -n /tmp/openwrt-ath79-nand-zte_mf286-squashfs-sysupgrade.bin - Wait for router to reboot to full OpenWrt. STEP 5: WAN connection establishment Since the router is equipped with LTE modem as its main WAN interface, it might be useful to connect to the Internet right away after installation. To do so, please put the following entries in /etc/config/network, replacing the specific configuration entries with one needed for your ISP: config interface 'wan' option proto 'qmi' option device '/dev/cdc-wdm0' option auth '<auth>' # As required, usually 'none' option pincode '<pin>' # If required by SIM option apn '<apn>' # As required by ISP option pdptype '<pdp>' # Typically 'ipv4', or 'ipv4v6' or 'ipv6' For example, the following works for most polish ISPs config interface 'wan' option proto 'qmi' option device '/dev/cdc-wdm0' option auth 'none' option apn 'internet' option pdptype 'ipv4' If you have build with LuCI, installing luci-proto-qmi helps with this task. Restoring the stock firmware: Preparation: If you took your backup using stock firmware, you will need to reassemble the partitions into images to be restored onto the flash. The layout might differ from ISP to ISP, this example is based on generic stock firmware. The only partitions you really care about are "web", "kernel", and "rootfs". For easy padding and possibly restoring configuration, you can concatenate most of them into images written into "ubi" meta-partition in OpenWrt. To do so, execute something like: cat mtd5_cfg-param.bin mtd6-oops.bin mtd7-web.bin mtd9-rootfs.bin > \ mtd8-ubi_restore.bin You can skip the "fota" partition altogether, it is used only for stock firmware update purposes and can be overwritten safely anyway. The same is true for "data" partition which on my device was found to be unused at all. Restoring mtd5_cfg-param.bin will restore the stock firmware configuration you had before. Method 1: Using initramfs: - Boot to initramfs as in step 3: - Completely detach ubi0 partition using ubidetach /dev/ubi0_0 - Look up the kernel and ubi partitions in /proc/mtd - Copy over the stock kernel image using scp to /tmp - Erase kernel and restore stock kernel: (scp mtd4_kernel.bin root@192.168.1.1:/tmp/) mtd write <kernel_mtd> mtd4_kernel.bin rm mtd4_kernel.bin - Copy over the stock partition backups one-by-one using scp to /tmp, and restore them individually. Otherwise you might run out of space in tmpfs: (scp mtd3_ubiconcat0.bin root@192.168.1.1:/tmp/) mtd write <ubiconcat0_mtd> mtd3_ubiconcat0.bin rm mtd3_ubiconcat0.bin (scp mtd5_ubiconcat1.bin root@192.168.1.1:/tmp/) mtd write <ubiconcat1_mtd> mtd5_ubiconcat1.bin rm mtd5_ubiconcat1.bin - If the write was correct, force a device reboot with reboot -f Method 2: Using live OpenWrt system (NOT RECOMMENDED): - Prepare a USB flash drive contatining MTD backup files - Ensure you have kmod-usb-storage and filesystem driver installed for your drive - Mount your flash drive mkdir /tmp/usb mount /dev/sda1 /tmp/usb - Remount your UBI volume at /overlay to R/O mount -o remount,ro /overlay - Write back the kernel and ubi partitions from USB drive cd /tmp/usb mtd write mtd4_kernel.bin /dev/<kernel_mtd> mtd write mtd8_ubi.bin /dev/<kernel_ubi> - If everything went well, force a device reboot with reboot -f Last image may be truncated a bit due to lack of space in RAM, but this will happen over "fota" MTD partition which may be safely erased after reboot anyway. Method 3: using built-in TFTP recovery (LAST RESORT): - Assemble a recovery rootfs image from backup of stock partitions by concatenating "web", "kernel", "rootfs" images dumped from the device, as "root_uImage" - Use it in place of "root_uImage" recovery initramfs image as in the TFTP pre-installation method. Quirks and known issues - Kernel partition size is increased to 4MB compared to stock 3MB, to accomodate future kernel updates - at this moment OpenWrt 5.10 kernel image is at 2.5MB which is dangerously close to the limit. This has no effect on booting the system - but keep that in mind when reassembling an image to restore stock firmware. - uqmi seems to be unable to change APN manually, so please use the one you used before in stock firmware first. If you need to change it, please use protocok '3g' to establish connection once, or use the following command to change APN (and optionally IP type) manually: echo -ne 'AT+CGDCONT=1,"IP","<apn>' > /dev/ttyUSB0 - The only usable LED as a "system LED" is the green debug LED hidden inside the case. All other LEDs are controlled by modem, on which the router part has some influence only on Wi-Fi LED. - Wi-Fi LED currently doesn't work while under OpenWrt, despite having correct GPIO mapping. All other LEDs are controlled by modem, including this one in stock firmware. GPIO19, mapped there only acts as a gate, while the actual signal source seems to be 5GHz Wi-Fi radio, however it seems it is not the LED exposed by ath10k as ath10k-phy0. - GPIO5 used for modem reset is a suicide switch, causing a hardware reset of whole board, not only the modem. It is attached to gpio-restart driver, to restart the modem on reboot as well, to ensure QMI connectivity after reboot, which tends to fail otherwise. - Modem, as in MF283+, exposes root shell over ADB - while not needed for OpenWrt operation at all - have fun lurking around. - MAC address shift for 5GHz Wi-Fi used in stock firmware is 0x320000000000, which is impossible to encode in the device tree, so I took the liberty of using MAC address increment of 1 for it, to ensure different BSSID for both Wi-Fi interfaces. Signed-off-by: Lech Perczak <lech.perczak@gmail.com>	2022-02-05 12:14:08 +01:00
Sungbo Eo	c7a559980a	ath79: improve support for Dongwon T&I DW02-412H * Move &nand node to DTSI * Utilize nvmem for fetching caldata * Rename build recipe, clean before build * Simplify KERNEL definition Signed-off-by: Sungbo Eo <mans0n@gorani.run>	2022-02-01 14:54:16 +09:00
Tamas Balogh	b21bc3479d	ath79: ASUS RP-AC66 use flash till the end This makes available the additional space, which was occupied by OEM's jffs2 partition before: "0x000000f80000-0x000001000000 : jffs2" Reverting to the OEM firmware will also recover this partition, i.e. it is not needed and can be used by OpenWrt. Signed-off-by: Tamas Balogh <tamasbalogh@hotmail.com>	2022-01-30 01:16:14 +09:00
Victorien Molle	af8a059bb4	ath79: add support for GL.iNet GL-XE300 The GL.iNet GL-XE300 is a 4G LTE Wireless router, based on QCA9531 SoC. Specifications: - SoC: QCA9531 (650MHz) - RAM: DDR2 128M - Flash: SPI NOR 16M + SPI NAND 128M - WiFi: 2.4GHz with 2 antennas - Ethernet: - 1x LAN (10/100M) - 1x WAN (10/100M) - LTE: - USB: 1x USB 2.0 port - UART: - 3.3V, TX, RX, GND / 115200 8N1 MAC addresses as verified by OEM firmware: use address source LAN :c5 art 0x0 (label) WAN :c6 label + 1 WLAN *:c7 art 0x1002 Installation via U-Boot rescue: 1. Press and hold reset and power buttons simultaneously 2. Wait for the LAN led to blink 5 times 3. Release reset and power buttons 4. The rescue page is accessible via http://192.168.1.1 5. Select the OpenWrt factory image and start upgrade 6. Wait for the router to flash new firmware and reboot Revert to stock firmware: i. Download the stock firmware from GL.Inet website ii. Use the same method explained above to flash the stock firmware Signed-off-by: Victorien Molle <victorien.molle@wifirst.fr> [update commit message] Signed-off-by: David Bauer <mail@david-bauer.net>	2022-01-22 01:17:16 +01:00
Lech Perczak	ebf639d282	ath79: use lzma-loader for ZyXEL NBG6716 Since gzip-compressed kernel image stopped fitting on 4MB kernel partition on the device, use lzma-loader wrapping LZMA-compressed kernel. This yields bootable device once again, and saves a very substantial amount of space, the kernel size decreasing from about 4.4MB to about 2.5MB for 5.10 kernel. This avoids changing of the flash layout for the device. While at that, reactivate the build for the device. Fixes: `5d8ea6d34f` ("ath79: Deactivate ZyXEL NBG6716 by default") Cc: André Valentin <avalentin@marcant.net> Cc: Hauke Mehrtens <hauke@hauke-m.de> Tested-by: Alex Henrie <alexhenrie24@gmail.com> Signed-off-by: Lech Perczak <lech.perczak@gmail.com>	2022-01-16 21:42:19 +01:00
Sven Eckelmann	8143709c90	ath79: Add support for OpenMesh OM2P v1 Device specifications: ====================== * Qualcomm/Atheros AR7240 rev 2 * 350/350/175 MHz (CPU/DDR/AHB) * 32 MB of RAM * 16 MB of SPI NOR flash - 2x 7 MB available; but one of the 7 MB regions is the recovery image * 2x 10/100 Mbps Ethernet * 1T1R 2.4 GHz Wi-Fi * 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power) * 1x GPIO-button (reset) * external h/w watchdog (enabled by default) * TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX) * 2x fast ethernet - eth0 + 18-24V passive POE (mode B) + used as WAN interface - eth1 + builtin switch port 4 + used as LAN interface * 12-24V 1A DC * external antenna The device itself requires the mtdparts from the uboot arguments to properly boot the flashed image and to support dual-boot (primary + recovery image). Unfortunately, the name of the mtd device in mtdparts is still using the legacy name "ar7240-nor0" which must be supplied using the Linux-specfic DT parameter linux,mtd-name to overwrite the generic name "spi0.0". Flashing instructions: ====================== Various methods can be used to install the actual image on the flash. Two easy ones are: ap51-flash ---------- The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be used to transfer the image to the u-boot when the device boots up. initramfs from TFTP ------------------- The serial console must be used to access the u-boot shell during bootup. It can then be used to first boot up the initramfs image from a TFTP server (here with the IP 192.168.1.21): setenv serverip 192.168.1.21 setenv ipaddr 192.168.1.1 tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr The actual sysupgrade image can then be transferred (on the LAN port) to the device via scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/ On the device, the sysupgrade must then be started using sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin Signed-off-by: Sven Eckelmann <sven@narfation.org>	2022-01-16 21:42:19 +01:00
Sven Eckelmann	1699c1dc7f	ath79: Add support for OpenMesh OM5P-AC v2 Device specifications: ====================== * Qualcomm/Atheros QCA9558 ver 1 rev 0 * 720/600/200 MHz (CPU/DDR/AHB) * 128 MB of RAM * 16 MB of SPI NOR flash - 2x 7 MB available; but one of the 7 MB regions is the recovery image * 2T2R 2.4 GHz Wi-Fi (11n) * 2T2R 5 GHz Wi-Fi (11ac) * 4x GPIO-LEDs (3x wifi, 1x power) * 1x GPIO-button (reset) * external h/w watchdog (enabled by default)) * TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX) * TI tmp423 (package kmod-hwmon-tmp421) for temperature monitoring * 2x ethernet - eth0 + AR8035 ethernet PHY (RGMII) + 10/100/1000 Mbps Ethernet + 802.3af POE + used as LAN interface - eth1 + AR8031 ethernet PHY (RGMII) + 10/100/1000 Mbps Ethernet + 18-24V passive POE (mode B) + used as WAN interface * 12-24V 1A DC * internal antennas This device support is based on the partially working stub from commit `53c474abbd` ("ath79: add new OF only target for QCA MIPS silicon"). Flashing instructions: ====================== Various methods can be used to install the actual image on the flash. Two easy ones are: ap51-flash ---------- The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be used to transfer the image to the u-boot when the device boots up. initramfs from TFTP ------------------- The serial console must be used to access the u-boot shell during bootup. It can then be used to first boot up the initramfs image from a TFTP server (here with the IP 192.168.1.21): setenv serverip 192.168.1.21 setenv ipaddr 192.168.1.1 tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr The actual sysupgrade image can then be transferred (on the LAN port) to the device via scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/ On the device, the sysupgrade must then be started using sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin Signed-off-by: Sven Eckelmann <sven@narfation.org>	2022-01-16 20:51:14 +01:00
Tamas Balogh	872b65ecc8	ath79: patch Asus RP-AC66 clean up and fix for sysupgrade image - clean up leftovers regarding MAC configure in dts - fix alphabetical order in caldata - IMAGE_SIZE for sysupgrade image Signed-off-by: Tamas Balogh <tamasbalogh@hotmail.com>	2022-01-15 17:41:19 +01:00
Sven Eckelmann	97f5617259	ath79: Add support for OpenMesh OM5P-AC v1 Device specifications: ====================== * Qualcomm/Atheros QCA9558 ver 1 rev 0 * 720/600/240 MHz (CPU/DDR/AHB) * 128 MB of RAM * 16 MB of SPI NOR flash - 2x 7 MB available; but one of the 7 MB regions is the recovery image * 2T2R 2.4 GHz Wi-Fi (11n) * 2T2R 5 GHz Wi-Fi (11ac) * 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power) * external h/w watchdog (enabled by default)) * TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX) * TI tmp423 (package kmod-hwmon-tmp421) for temperature monitoring * 2x ethernet - eth0 + AR8035 ethernet PHY (RGMII) + 10/100/1000 Mbps Ethernet + 802.3af POE + used as LAN interface - eth1 + AR8035 ethernet PHY (SGMII) + 10/100/1000 Mbps Ethernet + 18-24V passive POE (mode B) + used as WAN interface * 12-24V 1A DC * internal antennas Flashing instructions: ====================== Various methods can be used to install the actual image on the flash. Two easy ones are: ap51-flash ---------- The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be used to transfer the image to the u-boot when the device boots up. initramfs from TFTP ------------------- The serial console must be used to access the u-boot shell during bootup. It can then be used to first boot up the initramfs image from a TFTP server (here with the IP 192.168.1.21): setenv serverip 192.168.1.21 setenv ipaddr 192.168.1.1 tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr The actual sysupgrade image can then be transferred (on the LAN port) to the device via scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/ On the device, the sysupgrade must then be started using sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin Signed-off-by: Sven Eckelmann <sven@narfation.org>	2022-01-09 21:12:28 +01:00
Sven Eckelmann	72ef594550	ath79: Add support for OpenMesh OM5P-AN Device specifications: ====================== * Qualcomm/Atheros AR9344 rev 2 * 560/450/225 MHz (CPU/DDR/AHB) * 64 MB of RAM * 16 MB of SPI NOR flash - 2x 7 MB available; but one of the 7 MB regions is the recovery image * 1T1R 2.4 GHz Wi-Fi * 2T2R 5 GHz Wi-Fi * 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power) * 1x GPIO-button (reset) * external h/w watchdog (enabled by default) * TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX) * TI tmp423 (package kmod-hwmon-tmp421) for temperature monitoring * 2x ethernet - eth0 + AR8035 ethernet PHY + 10/100/1000 Mbps Ethernet + 802.3af POE + used as LAN interface - eth1 + 10/100 Mbps Ethernet + builtin switch port 1 + 18-24V passive POE (mode B) + used as WAN interface * 12-24V 1A DC * internal antennas Flashing instructions: ====================== Various methods can be used to install the actual image on the flash. Two easy ones are: ap51-flash ---------- The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be used to transfer the image to the u-boot when the device boots up. initramfs from TFTP ------------------- The serial console must be used to access the u-boot shell during bootup. It can then be used to first boot up the initramfs image from a TFTP server (here with the IP 192.168.1.21): setenv serverip 192.168.1.21 setenv ipaddr 192.168.1.1 tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr The actual sysupgrade image can then be transferred (on the LAN port) to the device via scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/ On the device, the sysupgrade must then be started using sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin Signed-off-by: Sven Eckelmann <sven@narfation.org>	2022-01-09 21:12:28 +01:00
Tamas Balogh	b29f4cf34c	ath79: add support for ASUS RP-AC66 Asus RP-AC66 Repeater Hardware specifications: Board: AP152 SoC: QCA9563 DRAM: 64MB DDR2 Flash: 25l128 16MB SPI-NOR LAN/WAN: 1x1000M QCA8033 WiFi 5GHz: QCA9880 Clocks: CPU:775.000MHz, DDR:650.000MHz, AHB:258.333MHz, Ref:25.000MHz MAC addresses as verified by OEM firmware: use address source Lan/Wan :24 art 0x1002 (label) 2G :24 art 0x1002 5G *:26 art 0x5006 Installation: Asus windows recovery tool: - install the Asus firmware restoration utility - unplug the router, hold the reset button while powering it on - release when the power LED flashes slowly - specify a static IP on your computer: IP address: 192.168.1.75 Subnet mask 255.255.255.0 - Start the Asus firmware restoration utility, specify the factory image and press upload - Do not power off the device after OpenWrt has booted until the LED flashing. TFTP Recovery method: - set computer to a static ip, 192.168.1.75 - connect computer to the LAN 1 port of the router - hold the reset button while powering on the router for a few seconds - send firmware image using a tftp client; i.e from linux: $ tftp tftp> binary tftp> connect 192.168.1.1 tftp> put factory.bin tftp> quit Signed-off-by: Tamas Balogh <tamasbalogh@hotmail.com>	2022-01-09 20:32:41 +01:00
Nick Hainke	cfa670bf16	ath79: add missing UBNT_REVISION The UBNT_REVISION was already added for the ubnt-xw target because: U-boot bootloader on M-XW devices expects factory image revision version in specific format. On airOS v6.1.7 with `U-Boot 1.1.4-s1039 (May 24 2017 - 15:58:18)` bootloader checks if the revision major(?) number is actually a number, but in currently generated images there's OpenWrt text and so the check fails ... By placing arbitrary correct number first in major version, we make the bootloader happy and we can flash factory images over TFTP again. commit `d42a7c4699` ("ath79: ubnt-m-xw: Fix factory image flashing using TFTP recovery method") Fixes errors in the form of (tftp flashing): sent DATA <block=8577, 412 bytes> received ERROR <code=2, msg=Firmware check failed> Error code 2: Firmware check failed The missing UBNT_REVISION was not noticed before, since the UBNT_REVISION field for the ubnt-xm target was also set to: "42.OpenWrt-..." Probably, UBNT_REVISION for the ubnt-xm target was set by the ubnt-xw and was never overridden somewhere else. However, it is missing and should be part of the ubnt-xm device. Signed-off-by: Nick Hainke <vincent@systemli.org>	2021-12-27 03:07:22 +01:00
Ryan Mounce	35aecc9d4a	ath79: add support for WD My Net N600 SoC: AR9344 RAM: 128MB Flash: 16MiB SPI NOR 5GHz WiFi: AR9382 PCIe 2x2:2 802.11n 2.4GHz WiFi: AR9344 (SoC) AHB 2x2:2 802.11n 5x Fast ethernet via SoC switch (green LEDs) 1x USB 2.0 4x front LEDs from SoC GPIO 1x front WPS button from SoC GPIO 1x bottom reset button from SoC GPIO UART header JP1, 115200 no parity 1 stop TX GND VCC (N/P) RX Flash factory image via "emergency room" recovery: - Configure your computer with a static IP 192.168.1.123/24 - Connect to LAN port on the N600 switch - Hold reset putton - Power on, holding reset until the power LED blinks slowly - Visit http://192.168.1.1/ and upload OpenWrt factory image - Wait at least 5 minutes for flashing, reboot and key generation - Visit http://192.168.1.1/ (OpenWrt LuCI) and upload OpenWrt sysupgrade image Signed-off-by: Ryan Mounce <ryan@mounce.com.au> [dt leds preparations] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>	2021-12-11 00:50:02 +01:00
Olivier Valentin	7853453950	ath79: add support for jjPlus JWAP230 The jjPlus JWAP230 is an access point board built around the QCA9558, with built-in 2.4GHz 3x3 N WiFi (28dBm). It can be expanded with 2 mini-PCIe boards, and has an USB2 root port. Specifications: - SOC: Qualcomm Atheros QCA9558 - CPU: 720MHz - H/W switch: QCA8327 rev 2 - Flash: 16 MiB SPI NOR (en25qh128) - RAM: 128 MiB DDR2 - WLAN: AR9550 built-in SoC bgn 3T3R (ath9k) - PCI: 2x mini-PCIe (optional 5V) - LEDs: 6x LEDs (3 are currently available) - Button: 1x Reset (not yet defined) - USB2: - 1x Type A root port - 1x combined mini-PCIe - Ethernet: - 2x 10/100/1000 (1x PoE 802.3af (36-57 V)) Notes: The device used to be supported in the ar71xx target. For upgrades: Please use "sysupgrade --force -n <image>". This will restore the device back to OpenWrt defaults! MAC address assignment: use source LAN art 0x0 WAN art 0x6 WLAN art 0x1002 (as part of the calibration data) Flash instructions: - install from u-boot with tftp (requires serial access) > setenv ipaddr a.b.c.d > setenv serverip e.f.g.h > tftp 0x80060000 \ openwrt-ath79-generic-jjplus_jwap230-squashfs-sysupgrade.bin > erase 0x9f050000 +${filesize} > cp.b $fileaddr 0x9f050000 $filesize > setenv bootcmd bootm 0x9f050000 > saveenv Signed-off-by: Olivier Valentin <valentio@free.fr> [Added DT-Leds (based on ar71xx), Added more notes about sysupgrade, fixed "qca9550" to match SoC in commit and dts file name] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>	2021-12-11 00:50:02 +01:00
Sander Vanheule	0f6b6aab2b	ath79: add support for TP-Link EAP225 v1 TP-Link EAP225 v1 is an AC1200 (802.11ac Wave-1) ceiling mount access point. Device specifications: * SoC: QCA9563 @ 775MHz * RAM: 128MiB DDR2 * Flash: 16MiB SPI-NOR * Wireless 2.4GHz (SoC): b/g/n, 2x2 * Wireless 5Ghz (QCA9882): a/n/ac, 2x2 * Ethernet (AR8033): 1× 1GbE, 802.3at PoE Flashing instructions: * Ensure the device is upgraded to firmware v1.4.0 * Exploit the user management page in the web interface to start telnetd by changing the username to `;/usr/sbin/telnetd -l/bin/sh&`. * Immediately change the malformed username back to something valid (e.g. 'admin') to make ssh work again. * Use the root shell via telnet to make /tmp world writeable (chmod 777) * Extract /usr/bin/uclited from the device via ssh and apply the binary patch listed below. The patch is required to prevent `uclited -u` in the last step from crashing. * Copy the patched uclited binary back to the device at /tmp/uclited (via ssh) * Upload the factory image to /tmp/upgrade.bin (via ssh) * Run `chmod +x /tmp/uclited && /tmp/uclited -u` to install OpenWrt. uclited patching: --- xxd uclited +++ xxd uclited-patched @@ -53811,7 +53811,7 @@ 000d2330: 8c44 0000 0320 f809 0000 0000 8fbc 0010 .D... .......... 000d2340: 8fa6 0a4c 02c0 2821 8f82 87c4 0000 0000 ...L..(!........ -000d2350: 8c44 0000 0c13 461c 27a7 0018 8fbc 0010 .D....F.'....... +000d2350: 8c44 0000 2402 0000 0000 0000 8fbc 0010 .D..$........... 000d2360: 1040 001d 0000 1821 8f99 8378 3c04 0058 .@.....!...x<..X 000d2370: 3c05 0056 2484 ad68 24a5 9f00 0320 f809 <..V$..h$.... .. To make sure the correct file is patched, the following MD5 checksums should match the unpatched and patched files: 4bd74183c23859c897ed77e8566b84de uclited 4107104024a2e0aeaf6395ed30adccae uclited-patched Debricking: * Serial port can be soldered on unpopulated 4-pin header (1: TXD, 2: RXD, 3: GND, 4: VCC) * Bridge unpopulated resistors running from pins 1 (TXD) and 2 (RXD). Do NOT bridge the pull-down for pin 2, running parallel to the header. * Use 3.3V, 115200 baud, 8n1 * Interrupt bootloader by holding CTRL+B during boot * tftp initramfs to flash via the LuCI web interface setenv ipaddr 192.168.1.1 # default, change as required setenv serverip 192.168.1.10 # default, change as required tftp 0x80800000 initramfs.bin bootelf $fileaddr Tested by forum user KernelMaker. Link: https://forum.openwrt.org/t/eap225-v1-firmware/87116 Signed-off-by: Sander Vanheule <sander@svanheule.net>	2021-12-05 18:49:14 +01:00
Catrinel Catrinescu	24d455d1d0	ath79: add Embedded Wireless Balin Platform Add the Embedded Wireless "Balin" platform, it is in ar71xx too SoC: QCA AR9344 or AR9350 RAM: DDR2-RAM 64MBytes Flash: SPI-NOR 16MBytes WLAN: 2 x 2 MIMO 2.4 & 5 GHz IEEE802.11 a/b/g/n Ethernet: 3 x 10/100 Mb/s USB: 1 x USB2.0 Host/Device bootstrap-pin at power-up PCIe: MiniPCIe - 1 x lane PCIe 1.2 Button: 1 x Reset-Button UART: 1 x Normal, 1 x High-Speed JTAG: 1 x EJTAG LED: 1 x Green Power/Status LED GPIO: 10 x Input/Output multiplexed The module comes already with the current vanilla OpenWrt firmware. To update, use "sysupgrade -n --force <image>" image directly in vendor firmware. This resets the existing configurations back to default! Signed-off-by: Catrinel Catrinescu <cc@80211.de> [indent, led function+color properties, fix partition unit-address, re-enable pcie port, mention button+led in commit message] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>	2021-12-03 12:30:08 +01:00
Hauke Mehrtens	cee0a95005	Revert "ath79: add support for Mikrotik LHG 5" This reverts commit `48774decea`. This commit does not contain a valid name in the Signed-off-by line. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>	2021-11-23 00:45:39 +01:00
Sebastian Schaper	25df327086	ath79: merge D-Link DAP-2695 with dtsi Further devices from the series have been added in the meantime, introducing `qca955x_dlink_dap-2xxx.dtsi`. Thus, merge support for DAP-2695 with the existing dtsi. This implies factory images can now be flashed via the regular OEM Web UI, as well as the bootloader recovery. Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>	2021-11-20 21:08:25 +01:00
Jakob (Jack/XDjackieXD)	48774decea	ath79: add support for Mikrotik LHG 5 The MikroTik LHG 5 series (product codes RBLHG-5nD, RBLHG-5HPnD and RBLHG-5HPnD-XL) devices are an outdoor 5GHz CPE with a 24.5dBi or 27dBi integrated antenna built around the Atheros AR9344 SoC. It is very similar to the SXT Lite5 series which this patch is based upon. Specifications: - SoC: Atheros AR9344 - RAM: 64 MB - Storage: 16 MB SPI NOR - Wireless: Atheros AR9340 (SoC) 802.11a/n 2x2:2 - Ethernet: Atheros AR8229 switch (SoC), 1x 10/100 port, 8-32 Vdc PoE in - 8 user-controllable LEDs: - 1x power (blue) - 1x user (white) - 1x ethernet (green) - 5x rssi (green) See https://mikrotik.com/product/RBLHG-5nD for more details. Notes: The device was already supported in the ar71xx target. Flashing: TFTP boot initramfs image and then perform a sysupgrade. Follow common MikroTik procedure as in https://openwrt.org/toh/mikrotik/common. Signed-off-by: Jakob (Jack/XDjackieXD) <jakob@chaosfield.at>	2021-11-20 21:08:25 +01:00
Roger Pueyo Centelles	c29f71ece7	ath79: mikrotik: enable USB module on RouterBoard wAPR-2nD The MikroTik RouterBOARD wAPR-2nD (wAP R) router features a miniPCI-e slot with USB lines connected, which are used by some USB cards with miniPCI-e form factor, like the R11e-LR8. Enabling USB support is required for such cards to work. Tested on a MikroTik wAP LR8 kit (RB wAPR-2nD + R11e-LR8). Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>	2021-11-20 21:08:21 +01:00
Piotr Dymacz	5dfa89be99	ath79: add support for Netgear R6100 Netgear R6100 is a dual-band Wi-Fi 5 (AC1200) router based on Qualcomm Atheros (AR9344 + QCA9882) platform. Support for this device was first introduced in `15f6f67d18` (ar71xx). FCC ID: PY312400225. Specifications: - Atheros AR9344 (560 MHz) - 128 MB of RAM (DDR2) - 128 MB of flash (parallel NAND) - 2T2R 2.4 GHz Wi-Fi (AR9344) - 2T2R 5 GHz Wi-Fi (QCA9882) - 5x 10/100 Mbps Ethernet (AR9344) - 4x internal antenna - 1x USB 2.0 (GPIO-controlled power) - 6x LED, 3x button (reset, Wi-Fi, WPS) - UART (4-pin, 2.54 mm pitch) header on PCB - 1x mechanical power switch - DC jack for main power input (12 V) WARNING: sysupgrade from older stable releases is not possible, fresh installation (via vendor's GUI or TFTP based recovery) is required. Reason for that is increased kernel partition size. Installation: Use the 'factory' image under vendor's GUI or via TFTP U-Boot recovery. You can use the 'nmrpflash' tool at a boot time, before kernel is loaded or start it manually by pressing the 'reset' button for ~20 seconds from powering up the device (U-Boot will start TFTP server on 192.168.1.1, use TFTP client to send the image). Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com> Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu> Signed-off-by: Michael Pratt <mcpratt@pm.me> Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>	2021-11-03 12:45:40 +01:00
Shiji Yang	184dc6e32a	ath79: add support for Letv LBA-047-CH Specifications: SOC: QCA9531 650 MHz ROM: 16 MiB Flash (Winbond W25Q128FV) RAM: 128 MiB DDR2 (Winbond W971GG6SB) LAN: 10/100M 2 WAN: 10/100M 1 LED: BGR color 1 Mac address: label C8:0E:77:xx:xx:68 art@0x0 lan C8:0E:77:xx:xx:62 art@0x6 wan C8:0E:77:xx:xx:68 art@0x0 (same as the label) wlan C8:0E:77:xx:xx:B2 art@0x1002 (load automatically) TFTP installation: Set local IP to 192.168.67.100 and open tftpd64, link lan port to computer. Rename "xxxx-factory.bin" to "openwrt-ar71xx-generic-ap147-16M-rootfs-squashfs.bin". * Make sure firmware file is in the tftpd's directory, push reset button and plug in, hold it for 5 seconds, and then it will download firmware from tftp server automatically. More information: * This device boot from flash@0xe80000 so we need a okli loader to deal with small kernel partition issue. In order to make full use of the storage space, connect a part of the previous kernel partition to the firmware. Stock Modify 0x000000-0x040000(u-boot) 0x000000-0x040000(u-boot) 0x040000-0x050000(u-boot-env) 0x000000-0x050000(u-boot-env) 0x050000-0xe80000(rootfs) 0x050000-0xe80000(firmware part1) 0xe80000-0xff0000(kernel) 0xe80000-0xe90000(okli-loader) 0xe90000-0xff0000(firmware part2) 0xff0000-0x1000000(art) 0xff0000-0x1000000(art) Signed-off-by: Shiji Yang <yangshiji66@qq.com>	2021-11-01 00:15:09 +01:00
Jihoon Han	84451173f0	ath79: add support for Dongwon T&I DW02-412H Dongwon T&I DW02-412H is a 2.4/5GHz band 11ac (WiFi-5) router, based on Qualcomm Atheros QCA9557. Specifications -------------- - SoC: Qualcomm Atheros QCA9557-AT4A - RAM: DDR2 128MB - Flash: SPI NOR 2MB (Winbond W25Q16DVSSIG / ESMT F25L16PA(2S)) + NAND 64/128MB - WiFi: - 2.4GHz: QCA9557 WMAC - 5GHz: QCA9882-BR4A - Ethernet: 5x 10/100/1000Mbps - Switch: QCA8337N-AL3C - USB: 1x USB 2.0 - UART: - JP2: 3.3V, TX, RX, GND (3.3V is the square pad) / 115200 8N1 Installation -------------- 1. Connect a serial interface to UART header and interrupt the autostart of kernel. 2. Transfer the factory image via TFTP and write it to the NAND flash. 3. Update U-Boot environment variable. > tftpboot 0x81000000 <your image>-factory.img > nand erase 0x1000000 > nand write 0x81000000 0x1000000 ${filesize} > setenv bootpart 2 > saveenv Revert to stock firmware -------------- 1. Revert to stock U-Boot environment variable. > setenv bootpart 1 > saveenv MAC addresses as verified by OEM firmware -------------- WAN: :XX (label) LAN: :XX + 1 2.4G: :XX + 3 5G: :XX + 4 The label MAC address was found in art 0x0. Credits -------------- Credit goes to the @manatails who first developed how to port OpenWRT to this device and had a significant impact on this patch. And thanks to @adschm and @mans0n for guiding me to revise the code in many ways. Signed-off-by: Jihoon Han <rapid_renard@renard.ga> Reviewed-by: Sungbo Eo <mans0n@gorani.run> Tested-by: Sungbo Eo <mans0n@gorani.run>	2021-10-31 21:58:28 +01:00
André Valentin	766d1d675b	ath79: fix parallel image generation for Zyxel NBG6716 This changes the image generation to use a unique directory. With parallel building it may occur that two concurrent jobs try to create an image which leds to errors. It also removes a needless subdirecory. Signed-off-by: André Valentin <avalentin@marcant.net>	2021-10-31 21:24:47 +01:00
Roger Pueyo Centelles	6801b827e4	ath79: mikrotik: enable SFP on RB921GS-5HPacD (mANTBox 15s) This patch enables the SFP cage on the MikroTik RouterBOARD 921GS-5HPacD (mANTBox 15s). The RB922UAGS-5HPacD had it already working, so the support code is moved to the common DTSI file both devices share. Tested on a RouterBOARD 921GS-5HPacD with a MikroTik S-53LC20D module. Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>	2021-10-31 21:24:47 +01:00
Christian Lamparter	e9335c2920	ath79: lzma-loader: fix & re-enable per-board CONFIG_BOARD_DEV Back in the AR71XX days, the lzma-loader code could be customized based on the $BOARD variable. These would be passed as a compile-time -DCONFIG_BOARD_$DEVICE_MODEL flag to the compiler. Hence, the lzma-loader would be able to include device-specific fixups. Note: There's still a fixup for the TpLink TL-WR1043ND V1 found in the lzma-loader's board.c code. But since the days of AR71XX I couldn't find a forum post or bug reported. So, I left it as is to not break anything by enabling it. => If you have a TL-WR1043ND V1 and you have problem with the ethernet: let me know. Because otherwise, the fixup might simply no longer needed with ath79 and it can be removed. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>	2021-10-22 21:25:18 +02:00
David Bauer	f85c970c9c	ath79: use correct USB package for DIR-505 AR9331 requires kmod-usb2-chipidea to use the USB ports. Include the correct package so they can be used with the base image. Signed-off-by: David Bauer <mail@david-bauer.net>	2021-10-21 15:52:49 +02:00
Adrian Schmutzler	2d977eb3d5	ath79: add recipe for common setup with loader-okli-compile These instructions are repeated for a few devices now, let's move them to shared definition so we do not repeat ourselves too often. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>	2021-10-02 21:26:12 +02:00
Andrew Cameron	ac03e24635	ath79: add support for TP-Link CPE710-v1 TP-Link CPE710-v1 is an outdoor wireless CPE for 5 GHz with one Ethernet port based on the AP152 reference board Specifications: - SoC: QCA9563-AL3A MIPS 74kc @ 775MHz, AHB @ 258MHz - RAM: 128MiB DDR2 @ 650MHz - Flash: 16MiB SPI NOR Based on the GD25Q128 - Wi-Fi 5Ghz: ath10k chip (802.11ac for up to 867Mbps on 5GHz wireless data rate) Based on the QCA9896 - Ethernet: one 1GbE port - 23dBi high-gain directional 2×2 MIMO antenna and a dedicated metal reflector - Power, LAN, WLAN5G Blue LEDs - 3x Blue LEDs Flashing instructions: Flash factory image through stock firmware WEB UI or through TFTP To get to TFTP recovery just hold reset button while powering on for around 30-40 seconds and release. Rename factory image to recovery.bin Stock TFTP server IP:192.168.0.100 Stock device TFTP address:192.168.0.254 Signed-off-by: Andrew Cameron <apcameron@softhome.net> [convert to nvmem, fix MAC assignment in 11-ath10k-caldata] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>	2021-09-25 19:28:54 +02:00
Robert Balas	baacdd53df	ath79: add support for TP-Link TL-WA1201 v2 This device is a wireless access point working on the 2.4 GHz and 5 GHz band, based on Qualcomm/Atheros QCA9563 + QCA9886. Specification - 775 MHz CPU - 128 MB of RAM (DDR2) - 16 MB of FLASH (SPI NOR) - QCA9563: 2.4 GHz 3x3 - QCA9886: 5 GHz - AR8033: 1x 1 Gbs Ethernet - 4x LED, WPS factory reset and power button - bare UART on PCB (accessible through testpoints) Methods for Flashing: - Apply factory image in OEM firmware web-gui. Wait a minute after the progress bar completes and restart the device. - Sysupgrade on top of existing OpenWRT image - Solder wires onto UART testpoints and attach a terminal. Boot the device and press enter to enter u-boot's menu. Then issue the following commands 1. setenv serverip your-server-ip setenv ipaddr your-device-ip 2. tftp 0x80060000 openwrt-squashfs.bin (Rembember output of size in hex, henceforth "sizeinhex") 3. erase 0x9f030000 +"sizeinhex" 4. cp.b 0x80060000 0x9f030000 0x"sizeinhex" 5. reboot Recover: - U-boot serial console Signed-off-by: Robert Balas <balasr@iis.ee.ethz.ch> [convert to nvmem] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>	2021-09-05 23:52:35 +02:00
Adrian Schmutzler	d37125b3f3	ath79: remove redundant BLOCKSIZE of 64k from devices BLOCKSIZE = 64k is set in Device/Default, i.e. global default on the target. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>	2021-08-30 00:37:35 +02:00
Sebastian Schaper	1c8214d6f2	ath79: fix spelling of DEVICE_MODEL for D-Link DAP-2695 Change `DAP-2965` to `DAP-2695` for device selection in menuconfig. Fixes: `cd09f26660` ("ath79: add support for D-Link DAP-2695-A1") Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net> [add Fixes] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>	2021-08-28 13:24:23 +02:00
Jan-Niklas Burfeind	d98738b5c1	ath79: add support for onion omega The Onion Omega is a hardware development platform with built-in WiFi. https://onioniot.github.io/wiki/ Specifications: - QCA9331 @ 400 MHz (MIPS 24Kc Big-Endian Processor) - 64MB of DDR2 RAM running at 400 MHz - 16MB of on-board flash storage - Support for USB 2.0 - Support for Ethernet at 100 Mbps - 802.11b/g/n WiFi at 150 Mbps - 18 digital GPIOs - A single Serial UART - Support for SPI - Support for I2S Flash instructions: The device is running OpenWrt upon release using the ar71xx target. Both a sysupgrade and uploading the factory image using u-boots web-UI do work fine. Depending on the ssh client, it might be necessary to enable outdated KeyExchange methods e.g. in the clients ssh-config: Host 192.168.1.1 KexAlgorithms +diffie-hellman-group1-sha1 The stock credentials are: root onioneer For u-boots web-UI manually configure `192.168.1.2/24` on your computer, connect to `192.168.1.1`. MAC addresses as verified by OEM firmware: 2G phy0 label LAN eth0 label - 1 LAN is only available in combination with an optional expansion dock. Based on vendor acked commit: commit `5cd49bb067` ("ar71xx: add support for Onion Omega") Partly reverts: commit `fc553c7e4c` ("ath79: drop unused/incomplete dts") Signed-off-by: Jan-Niklas Burfeind <git@aiyionpri.me>	2021-08-26 15:07:18 +02:00
Romain Mahoux	e2d08084c3	ath79: add support for Compex WPJ558 (16M) Specifications: - SoC: QCA9558 - DRAM: 128MB DDR2 - Flash: 16MB SPI-NOR - Wireless: on-board abgn 2×2 2.4GHz radio - Ethernet: 2x 10/100/1000 Mbps (1x 802.11af PoE) - miniPCIe slot Flash instruction: - From u-boot tftpboot 0x80500000 openwrt-ath79-generic-compex_wpj558-16m-squashfs-sysupgrade.bin erase 0x9f030000 +$filesize cp.b $fileaddr 0x9f030000 $filesize boot - From cpximg loader The cpximg loader can be started either by holding the reset button during power up. Once it's running, a TFTP-server under 192.168.1.1 will accept the image appropriate for the board revision that is etched on the board. For example, if the board is labelled '6A07': tftp -v -m binary 192.168.1.1 -c put openwrt-ath79-generic-compex_wpj558-16m-squashfs-cpximg-6a07.bin Signed-off-by: Romain Mahoux <romain@mahoux.fr> [convert to nvmem, remove redundant lan_mac in 02_network] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>	2021-08-25 01:42:17 +02:00
Zoltan HERPAI	98eb95dd00	ath79: add support for Atheros DB120 reference board Atheros DB120 reference board. Specifications: SoC: QCA9344 DRAM: 128Mb DDR2 Flash: 8Mb SPI-NOR, 128Mb NAND flash Switch: 5x 10/100Mbps via AR8229 switch (integrated into SoC), 5x 10/100/1000Mbps via QCA8237 via RGMII WLAN: AR9300 (SoC, 2.4G+5G) + AR9340 (PCIe, 5G-only) USB: 1x 2.0 UART: standard QCA UART header JTAG: yes Button: 1x reset LEDs: a lot Slots: 2x mPCIe + 1x mini-PCI, but using them requires additional undocumented changes. Misc: The board allows to boot off NAND, and there is I2S audio support as well - also requiring additional undocumented changes. Installation: 1. Original bootloader Connect the board to ethernet Set up a server with an IP address of 192.168.1.10 Make the openwrt-ath79-generic-atheros_db120-squashfs-factory.bin available via TFTP tftpboot 0x80060000 openwrt-ath79-generic-atheros_db120-squashfs-factory.bin erase 0x9f050000 +$filesize cp.b $fileaddr 0x9f050000 $filesize 2. pepe2k's u-boot_mod Connect the board to ethernet Set up a server with an IP address of 192.168.1.10 Make the openwrt-ath79-generic-atheros_db120-squashfs-factory.bin available via TFTP, as "firmware.bin" run fw_upg Reboot the board. Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu> [explicit factory recipe in generic.mk, sorting in 10-ath9k-eeprom, convert to nvmem, use fwconcat* names in DTS, remove unneeded DT labels, remove redundant uart node] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>	2021-08-22 23:02:08 +02:00
Russell Senior	61b49cd3f8	ath79: add support for Ubiquiti PowerBeam M2 (XW) This patch adds support for the Ubiquiti PowerBeam M2 (XW), e.g. PBE-M2-400, a 802.11n wireless with a feed+dish form factor. This device was previously supported by the ar71xx loco-m-xw firmware. Specifications: - Atheros AR9342 SoC - 64 MB RAM - 8 MB SPI flash - 1x 10/100 Mbps Ethernet port, 24 Vdc PoE-in - Power and LAN green LEDs - 4x RSSI LEDs (red, orange, green, green) - UART (115200 8N1) Flashing via stock GUI: - Downgrade to AirOS v5.5.x (latest available is 5.5.10-u2) first (see https://openwrt.org/toh/ubiquiti/powerbeam installation instructions) - Upload the factory image via AirOS web GUI. Flashing via TFTP: - Use a pointy tool (e.g., unbent paperclip) to keep the reset button pressed. - Power on the device (keep reset button pressed). - Keep pressing until LEDs flash alternatively LED1+LED3 => LED2+LED4 => LED1+LED3, etc. - Release reset button. - The device starts a TFTP server at 192.168.1.20. - Set a static IP on the computer (e.g., 192.168.1.21/24). - Upload via tftp the factory image: $ tftp 192.168.1.20 tftp> bin tftp> trace tftp> put openwrt-ath79-generic-ubnt_powerbeam-m2-xw-squashfs-factory.bin WARNING: so far, no non-destructive method has been discovered for opening the enclosure to reach the serial console. Internal photos are available here: https://fcc.io/SWX-NBM2HP Signed-off-by: Russell Senior <russell@personaltelco.net>	2021-08-22 22:41:52 +02:00
Russell Senior	96db7d2a73	ath79: rename Ubiquiti PowerBeam M (XW) to PowerBeam M5 (XW) The commit [1] added support for Ubiquiti PowerBeam M (XW), tested on the PBE-M5-400. But, it turns out the PBE-M2-400 has a different ethernet configuration, so make the support specific to the m5 version in anticipation of adding specific support for the m2 in a separate commit. [1] `12eb5b2384` ("ath79: add support for Ubiquiti PowerBeam M (XW)") Signed-off-by: Russell Senior <russell@personaltelco.net> [fix model name in DTS, format commit reference in commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>	2021-08-22 22:41:41 +02:00
John Marrett	252466a0ce	ath79: add support for GL.iNet GL-X300B The GL-X300B is a industrial 4G LTE router based on the Qualcomm QCA9531 SoC. Specifications: - Qualcomm QCA9531 @ 650 MHz - 128 MB of RAM - 16 MB of SPI NOR FLASH - 2x 10/100 Mbps Ethernet - 2.4GHz 802.11b/g/n - 1x USB 2.0 (vbus driven by GPIO) - 4x LED, driven by GPIO - 1x button (reset) - 1x mini pci-e slot (vcc driven by GPIO) - RS-485 Serial Port (untested) Flash instructions: This firmware can be flashed using either sysupgrade from the GL.iNet firmware or the recovery console as follows: - Press and hold the reset button - Connect power to the router, wait five seconds - Manually configure 192.168.1.2/24 on your computer, connect to 192.168.1.1 - Upload the firmware image using the web interface RS-485 serial port is untested and may depend on the following commit in the GL.iNet repo: `202e83a32a` MAC addresses as verified by OEM firmware: vendor OpenWrt address WAN eth0 label LAN eth1 label + 1 2g phy0 label + 2 The label MAC address was found in the art partition at 0x0 Based on vendor commit: `16c5708b20` Signed-off-by: John Marrett <johnf@zioncluster.ca>	2021-08-05 01:48:17 +02:00
Vincent Wiemann	55b4b36552	ath79: add support for Joy-IT JT-OR750i Specifications: * QCA9531, 16 MiB flash (Winbond W25Q128JVSQ), 128 MiB RAM * 802.11n 2T2R (external antennas) * QCA9887, 802.11ac 1T1R (connected with diplexer to one of the antennas) * 3x 10/100 LAN, 1x 10/100 WAN * UART header with pinout printed on PCB Installation: * The device comes with a bootloader installed only * The bootloader offers DHCP and is reachable at http://10.123.123.1 * Accept the agreement and flash sysupgrade.bin * Use Firefox if flashing does not work TFTP recovery with static IP: * Rename sysupgrade.bin to jt-or750i_firmware.bin * Offer it via TFTP server at 192.168.0.66 * Keep the reset button pressed for 4 seconds after connecting power TFTP recovery with dynamic IP: * Rename sysupgrade.bin to jt-or750i_firmware.bin * Offer it via TFTP server with a DHCP server running at the same address * Keep the reset button pressed for 6 seconds after connecting power Co-authored-by: Sebastian Schaper <openwrt@sebastianschaper.net> Signed-off-by: Vincent Wiemann <vincent.wiemann@ironai.com>	2021-07-28 13:48:15 +02:00
Roberto Valentini	af56075a8f	ath79: add support for TP-Link RE455 v1 TP-Link RE455 v1 is a dual band router/range-extender based on Qualcomm/Atheros QCA9563 + QCA9880. This device is nearly identical to RE450 v3 Specification: - 775 MHz CPU - 64 MB of RAM (DDR2) - 8 MB of FLASH (SPI NOR) - 3T3R 2.4 GHz - 3T3R 5 GHz - 1x 10/100/1000 Mbps Ethernet (AR8033 PHY) - 7x LED, 4x button - UART header on PCB[1] Flash instruction: Apply factory image in OEM firmware web-gui. [1] Didn't work, probably need to short unpopulated resistor R64 and R69 as RE450v3 Signed-off-by: Roberto Valentini <valantin89@gmail.com>	2021-07-11 16:58:12 +02:00
Adrian Schmutzler	cce8d16bf1	treewide: call check-size before append-metadata sysupgrade metadata is not flashed to the device, so check-size should be called _before_ adding metadata to the image. While at it, do some obvious wrapping improvements. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Acked-by: Paul Spooren <mail@aparcar.org>	2021-07-10 19:40:10 +02:00
Evgeniy Isaev	6c148116f7	ath79: add support for Xiaomi AIoT Router AC2350 Device specifications * SoC: QCA9563 @ 775MHz (MIPS 74Kc) * RAM: 128MiB DDR2 * Flash: 16MiB SPI-NOR (EN25QH128) * Wireless 2.4GHz (SoC): b/g/n, 3x3 * Wireless 5Ghz (QCA9988): a/n/ac, 4x4 MU-MIMO * IoT Wireless 2.4GHz (QCA6006): currently unusable * Ethernet (AR8327): 3 LAN × 1GbE, 1 WAN × 1GbE * LEDs: Internet (blue/orange), System (blue/orange) * Buttons: Reset * UART: through-hole on PCB ([VCC 3.3v](RX)(GND)(TX) 115200, 8n1) * Power: 12VDC, 1,5A MAC addresses map (like in OEM firmware) art@0x0 88:C3:97::57 wan/label art@0x1002 88:C3:97::2D lan/wlan2g art@0x5006 88:C3:97::2C wlan5g Obtain SSH Access 1. Download and flash the firmware version 1.3.8 (China). 2. Login to the router web interface and get the value of `stok=` from the URL 3. Open a new tab and go to the following URL (replace <STOK> with the stok value gained above; line breaks are only for easier handling, please put together all four lines into a single URL without any spaces): http://192.168.31.1/cgi-bin/luci/;stok=<STOK>/api/misystem/set_config_iotdev ?bssid=any&user_id=any&ssid=-h%0Anvram%20set%20ssh_en%3D1%0Anvram%20commit %0Ased%20-i%20%27s%2Fchannel%3D.%2A%2Fchannel%3D%5C%5C%22debug%5C%5C%22%2F g%27%20%2Fetc%2Finit.d%2Fdropbear%0A%2Fetc%2Finit.d%2Fdropbear%20start%0A 4. Wait 30-60 seconds (this is the time required to generate keys for the SSH server on the router). Create Full Backup 1. Obtain SSH Access. 2. Create backup of all flash (on router): dd if=/dev/mtd0 of=/tmp/ALL.backup 3. Copy backup to PC (on PC): scp root@192.168.31.1:/tmp/ALL.backup ./ Tip: backup of the original firmware, taken three times, increases the chances of recovery :) Calculate The Password Locally using shell (replace "12345/E0QM98765" with your router's serial number): On Linux printf "%s6d2df50a-250f-4a30-a5e6-d44fb0960aa0" "12345/E0QM98765" \| \ md5sum - \| head -c8 && echo On macOS printf "%s6d2df50a-250f-4a30-a5e6-d44fb0960aa0" "12345/E0QM98765" \| \ md5 \| head -c8 * Locally using python script (replace "12345/E0QM98765" with your router's serial number): wget https://raw.githubusercontent.com/eisaev/ax3600-files/master/scripts/calc_passwd.py python3.7 -c 'from calc_passwd import calc_passwd; print(calc_passwd("12345/E0QM98765"))' * Online https://www.oxygen7.cn/miwifi/ Debricking (lite) If you have a healthy bootloader, you can use recovery via TFTP using programs like TinyPXE on Windows or dnsmasq on Linux. To switch the router to TFTP recovery mode, hold down the reset button, connect the power supply, and release the button after about 10 seconds. The router must be connected directly to the PC via the LAN port. Debricking You will need a full dump of your flash, a CH341 programmer, and a clip for in-circuit programming. Install OpenWRT 1. Obtain SSH Access. 2. Create script (on router): echo '#!/bin/sh' > /tmp/flash_fw.sh echo >> /tmp/flash_fw.sh echo '. /bin/boardupgrade.sh' >> /tmp/flash_fw.sh echo >> /tmp/flash_fw.sh echo 'board_prepare_upgrade' >> /tmp/flash_fw.sh echo 'mtd erase rootfs_data' >> /tmp/flash_fw.sh echo 'mtd write /tmp/openwrt.bin firmware' >> /tmp/flash_fw.sh echo 'sleep 3' >> /tmp/flash_fw.sh echo 'reboot' >> /tmp/flash_fw.sh echo >> /tmp/flash_fw.sh chmod +x /tmp/flash_fw.sh 3. Copy `openwrt-ath79-generic-xiaomi_aiot-ac2350-squashfs-sysupgrade.bin` to the router (on PC): scp openwrt-ath79-generic-xiaomi_aiot-ac2350-squashfs-sysupgrade.bin \ root@192.168.31.1:/tmp/openwrt.bin 4. Flash OpenWRT (on router): /bin/ash /tmp/flash_fw.sh & 5. SSH connection will be interrupted - this is normal. 6. Wait for the indicator to turn blue. Signed-off-by: Evgeniy Isaev <isaev.evgeniy@gmail.com> [improve commit message formatting slightly] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>	2021-07-05 00:28:04 +02:00
Diogenes Rengo	cce2e8db56	ath79: add support for TP-Link TL-WR941HP v1 Specifications: SOC: Qualcomm Atheros TP9343 (750 MHz) Flash: 8 Mb (GigaDevice GD25Q64CSIG) RAM: 64 Mb (Zentel A3R12E40DBF-8E) Serial: yes, 4-pin header Wlan: Qualcomm Atheros TP9343, antenna: MIM0 3x3:3 RP-SMA 3 x 2.4GHz power amp module Skyworks (SiGe) SE2576L Ethernet: Qualcomm Atheros TP9343 Lan speed: 100M ports: 4 Lan speed: 100M ports: 1 Other info: same case, ram and flash that TP-Link TL-WR841HP, different SOC https://forum.openwrt.org/t/adding-device-support-tp-link-wr941hp/ Label MAC addresses based on vendor firmware: LAN :ee label WAN :ef label +1 WLAN *:ee label The label MAC address found in "config" partition at 0x8 Flash instruction: Upload the generated factory firmware on web interface. Signed-off-by: Diogenes Rengo <rengocbx250@gmail.com> [remove various whitespace issues, squash commits, use short 0x0] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>	2021-07-04 18:07:35 +02:00
Russell Senior	12eb5b2384	ath79: add support for Ubiquiti PowerBeam M (XW) This patch adds support for the Ubiquiti PowerBeam M (XW), e.g. PBE-M5-400, a 802.11n wireless with a feed+dish form factor. This device was previously supported by the ar71xx loco-m-xw firmware. Specifications: - Atheros AR9342 SoC - 64 MB RAM - 8 MB SPI flash - 1x 10/100 Mbps Ethernet port, 24 Vdc PoE-in - Power and LAN green LEDs - 4x RSSI LEDs (red, orange, green, green) - UART (115200 8N1) Flashing via stock GUI: - Downgrade to AirOS v5.5.x (latest available is 5.5.10-u2) first (see https://openwrt.org/toh/ubiquiti/powerbeam installation instructions) - Upload the factory image via AirOS web GUI. Flashing via TFTP: - Use a pointy tool (e.g., unbent paperclip) to keep the reset button pressed. - Power on the device (keep reset button pressed). - Keep pressing until LEDs flash alternatively LED1+LED3 => LED2+LED4 => LED1+LED3, etc. - Release reset button. - The device starts a TFTP server at 192.168.1.20. - Set a static IP on the computer (e.g., 192.168.1.21/24). - Upload via tftp the factory image: $ tftp 192.168.1.20 tftp> bin tftp> trace tftp> put openwrt-ath79-generic-xxxxx-ubnt_powerbeam-m-xw-squashfs-factory.bin WARNING: so far, no non-destructive method has been discovered for opening the enclosure to reach the serial console. Internal photos are available here: https://fcc.io/SWX-NBM5HP Signed-off-by: Russell Senior <russell@personaltelco.net>	2021-07-04 14:42:08 +02:00
David Bauer	6cf1dfd7e1	ath79: add support for Teltonika RUT230 v1 This commit adds support for the Teltonika RUT230 v1, a Atheros AR9331 based router with a Quectel UC20 UMTS modem. Hardware -------- Atheros AR9331 16 MB SPI-NOR XTX XT25F128B 64M DDR2 memory Atheros AR9331 1T1R 802.11bgn Wireless Boootloader: pepe2k U-Boot mod Hardware-Revision ----------------- There are two board revisions of the RUT230, a v0 and v1. A HW version is silkscreened on the top of the PCBs front side as well as shown in the Teltonika UI. However, this looks to be a different identifier, as the GPl dump shows this silkscreened / UI shown version are internally treated identically. Th following mapping has been obtained from the latest GPl dump. HW Ver 01 - 04 --> v0 HW Ver > 05 --> v1 My board was a HW Ver 09 and is treated as a v1. Installation ------------ While attaching power, hold down the reset button and release it after the signal LEDs flashed 3 times. Attach your Computer with the devices LAN port and assign yourself the IPv4 address 192.168.1.10/24. Open a web browser, navigate to 192.168.1.1. Upload the OpenWrt factory image. The device will install OpenWrt and automatically reboots afterwards. You can use the smae procedure with the stock firmware to return back to the vendor firmware. Signed-off-by: David Bauer <mail@david-bauer.net>	2021-06-30 21:39:59 +02:00
Koen Vandeputte	39e53f72f7	ath79: mikrotik: remove rb912 gpio-beeper module dependency The beeper is currently not fully functional and has also been removed from DTS. Also remove the dependency for the gpio-beeper module. Fixes: `695a1cd53c` ("ath79: add support for MikroTik RouterBOARD 912UAG-2HPnD") Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>	2021-06-28 11:07:35 +02:00
Denis Kalashnikov	695a1cd53c	ath79: add support for MikroTik RouterBOARD 912UAG-2HPnD This board has been supported in the ar71xx. Links: * https://mikrotik.com/product/RB912UAG-2HPnD * https://openwrt.org/toh/hwdata/mikrotik/mikrotik_rb912uag-2hpnd This also supports the 5GHz flavour of the board. Hardware: * SoC: Atheros AR9342, * RAM: DDR 64MB, * SPI NOR: 64KB, * NAND: 128MB, * Ethernet: x1 10/100/1000 port with passive POE in, * Wi-Fi: 802.11 b/g/n, * PCIe, * USB: 2.0 EHCI controller, connected to mPCIe slot and a Type-A port -- both can be used for LTE modem, but only one can be used at any time. * LEDs: 5 general purpose LEDs (led1..led5), power LED, user LED, Ethernet phy LED, * Button, * Beeper. Not working: * Button: it shares gpio line 15 with NAND ALE and NAND IO7, and current drivers doesn't easily support this configuration, * Beeper: it is connected to bit 5 of a serial shift register (tested with sysfs led trigger timer). But kmod-gpio-beeper doesn't work -- we left this as is for now. Flashing: * Use the RouterBOARD Reset button to enable TFTP netboot, boot kernel and initramfs and then perform sysupgrade. * From ar71xx OpenWrt firmware run: $ sysupgrade -F /tmp/<sysupgrade.bin> For more info see: https://openwrt.org/toh/mikrotik/common. Co-Developed-by: Koen Vandeputte <koen.vandeputte@citymesh.com> Reviewed-by: Sergey Ryazanov <ryazanov.s.a@gmail.com> Signed-off-by: Denis Kalashnikov <denis281089@gmail.com>	2021-06-21 10:48:27 +02:00
Andy Lee	c5235f6b24	ath79: add support for TP-Link TL-WR841HP v3 Specifications: - QCA9533 SoC, 8 MB nor flash, 64 MB DDR2 RAM - 2x2 9dBi antenna, wifi 2.4Ghz 300Mbps - 4x Ethernet LAN 10/100, 1x Ethernet WAN 10/100 - 1x WAN, LAN, Wifi, PWR, WPS, RE Leds - Reset, Wifi on/off, WPS, RE buttons - Serial UART at J4 onboard: 3.3v GND RX TX, 1152008N1 Label MAC addresses based on vendor firmware: LAN :ea label WAN :eb label +1 2.4 GHz *:ea label The label MAC address in found in u-boot 0x1fc00 Installation: Upload openwrt-ath79-generic-tplink_tl-wr841hp-v3-squashfs-factory.bin from stock firmware webgui. Maybe we need rename to shorten file name due to stock webgui error. Revert back to stock firmware instructions: - set your PC to static IP address 192.168.0.66 netmask 255.255.255.0 - download stock firmware from Tp-link website - put it in the root directory of tftp server software - rename it to wr841hpv3_tp_recovery.bin - power on while pressing Reset button until any Led is lighting up - wait for the router to reboot. done Forum support topic: https://forum.openwrt.org/t/support-for-tp-link-tl-wr841hp-v3-router Signed-off-by: Andy Lee <congquynh284@yahoo.com> [rebase and squash] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>	2021-06-13 23:30:05 +02:00
Nick Hainke	3e0387b3db	ath79: Support for Ubiquiti Rocket 5AC Lite The Ubiquiti Rocket 5AC Lite (R5AC-Lite) is an outdoor router. Specifications: - SoC: Qualcomm Atheros QCA9558 - RAM: 128 MB - Flash: 16 MB SPI - Ethernet: 1x 10/100/1000 Mbps - WiFi 5 GHz: QCA988x - Buttons: 1x (reset) - LEDs: 1x power, 1x Ethernet, 4x RSSI Installation: - Instructions for XC-type Ubiquiti: https://openwrt.org/toh/ubiquiti/common Signed-off-by: Nick Hainke <vincent@systemli.org>	2021-06-07 00:23:51 +02:00
INAGAKI Hiroshi	a4e2766a5b	ath79: add support for NEC Aterm WF1200CR NEC Aterm WF1200CR is a 2.4/5 GHz band 11ac (Wi-Fi 5) router, based on QCA9561. Specification: - SoC : Qualcomm Atheros QCA9561 - RAM : DDR2 128 MiB (W971GG6SB-25) - Flash : SPI-NOR 8 MiB (MX25L6433FM2I-08G) - WLAN : 2.4/5 GHz 2T2R - 2.4 GHz : QCA9561 (SoC) - 5 GHz : QCA9888 - Ethernet : 2x 10/100 Mbps - Switch : QCA9561 (SoC) - LEDs/Keys : 8x/3x (2x buttons, 1x slide-switch) - UART : through-hole on PCB - JP1: Vcc, GND, NC, TX, RX from "JP1" marking - 115200n8 - Power : 12 VDC, 0.9 A Flash instruction using factory image (stock: < v1.3.2): 1. Boot WF1200CR normally with "Router" mode 2. Access to "http://192.168.10.1/" and open firmware update page ("ファームウェア更新") 3. Select the OpenWrt factory image and click update ("更新") button to perform firmware update 4. Wait ~150 seconds to complete flashing Alternate flash instruction using initramfs image (stock: >= v1.3.2): 1. Prepare the TFTP server with the IP address 192.168.1.10 and place the OpenWrt initramfs image to the TFTP directory with the name "0101A8C0.img" 2. Connect serial console to WF1200CR 3. Boot WF1200CR and interrupt with any key after the message "Hit any key to stop autoboot: 2", the U-Boot starts telnetd after the message "starting telnetd server from server 192.168.1.1" 4. login the telnet (address: 192.168.1.1) 5. Perform the following commands to modify "bootcmd" variable temporary and check the value (to ignore the limitation of available commands, "tp; " command at the first is required as dummy, and the output of "printenv" is printed on the serial console) tp; set bootcmd 'set autostart yes; tftpboot' tp; printenv 6. Save the modified variable with the following command and reset device tp; saveenv tp; reset 7. The U-Boot downloads initramfs image from TFTP server and boots it 8. On initramfs image, download the sysupgrade image to the device and perform the following commands to erase stock firmware and sysupgrade mtd erase firmware sysupgrade <sysupgrade image> 9. After the rebooting by completion of sysupgrade, start U-Boot telnetd and login with the same way above (3, 4) 10. Perform the following commands to reset "bootcmd" variable to the default and reset the device tp; run seattle tp; reset (the contents of "seattle": setenv bootcmd 'bootm 0x9f070040' && saveenv) 11. Wait booting-up the device Known issues: - the following 6x LEDs are connected to the gpio controller on QCA9888 chip and the implementation of control via the controller is missing in ath10k/ath10k-ct - "ACTIVE" (Red/Green) - "2.4GHz" (Red/Green) - "5GHz" (Red/Green) Note: - after the version v1.3.2 of stock firmware, "offline update" by uploading image by user is deleted and the factory image cannot be used - the U-Boot on WF1200CR doesn't configure the port-side LEDs on WAN/LAN and the configuration is required on OpenWrt - gpio-hog: set the direction of GPIO 14(WAN)/19(LAN) to output - pinmux: set GPIO 14/19 as switch-controlled LEDs Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>	2021-06-06 21:21:51 +02:00
Felix Matouschek	624b85e646	ath79: add support for Devolo dLAN pro 1200+ WiFi ac This patch adds support for the Devolo dLAN pro 1200+ WiFi ac. This device is a plc wifi AC2400 router/extender with 2 Ethernet ports, has a QCA7500 PLC and uses the HomePlug AV2 standard. Other than the PLC the hardware is identical to the Devolo Magic 2 WIFI. Therefore it uses the same dts, which was moved to a dtsi to be included by both boards. This is a board that was previously included in the ar71xx tree. Hardware: SoC: AR9344 CPU: 560 MHz Flash: 16 MiB (W25Q128JVSIQ) RAM: 128 MiB DDR2 Ethernet: 2xLAN 10/100/1000 PLC: QCA75000 (Qualcomm HPAV2) PLC Uplink: 1Gbps MIMO PLC Link: RGMII 1Gbps (WAN) WiFi: Atheros AR9340 2.4GHz 802.11bgn Atheros AR9882-BR4A 5GHz 802.11ac Switch: QCA8337, Port0:CPU, Port2:PLC, Port3:LAN1, Port4:LAN2 Button: 3x Buttons (Reset, wifi and plc) LED: 3x Leds (wifi, plc white, plc red) GPIO Switch: 11-PLC Pairing (Active Low) 13-PLC Enable 21-WLAN power MACs Details verified with the stock firmware: Radio1: 2.4 GHz &wmac :4c Art location: 0x1002 Radio0: 5.0 GHz &pcie :4d Art location: 0x5006 Ethernet &ethernet :4e = 2.4 GHz + 2 PLC uplink --- :4f = 2.4 GHz + 3 Label MAC address is from PLC uplink The Powerline (PLC) interface of the dLAN pro 1200+ WiFi ac requires 3rd party firmware which is not available from standard OpenWrt package feeds. There is a package feed on github which you must add to OpenWrt buildroot so you can build a firmware image which supports the plc interface. See: https://github.com/0xFelix/dlan-openwrt (forked from Devolo and added compatibility for OpenWrt 21.02) Flash instruction (TFTP): 1. Set PC to fixed ip address 192.168.0.100 2. Download the sysupgrade image and rename it to uploadfile 3. Start a tftp server with the image file in its root directory 4. Turn off the router 5. Press and hold Reset button 6. Turn on router with the reset button pressed and wait ~15 seconds 7. Release the reset button and after a short time the firmware should be transferred from the tftp server 8. Allow 1-2 minutes for the first boot. Signed-off-by: Felix Matouschek <felix@matouschek.org> [add "plus" to compatible and device name] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>	2021-06-06 18:56:45 +02:00
Zoltan HERPAI	1eb481206d	ath79: add support for Qualcomm AP143 reference boards Specifications: SoC: QCA9533 DRAM: 32Mb DDR1 Flash: 8/16Mb SPI-NOR LAN: 4x 10/100Mbps via AR8229 switch (integrated into SoC) on GMII WAN: 1x 10/100Mbps via MII WLAN: QCA9530 USB: 1x 2.0 UART: standard QCA UART header JTAG: yes Button: 1x WPS, 1x reset LEDs: 8x LEDs A version with 4Mb flash is also available, but due to lack of enough space it's not supported. As the original flash layout does not provide enough space for the kernel (1472k), the firmware uses OKLI and concat flash to overcome the limitation without changing the boot address of the bootloaders. Installation: 1. Original bootloader Connect the board to ethernet Set up a server with an IP address of 192.168.1.10 Make the openwrt-ath79-generic-qca_ap143-8m-squashfs-factory.bin available via TFTP tftpboot 0x80060000 openwrt-ath79-generic-qca_ap143-8m-squashfs-factory.bin erase 0x9f050000 +$filesize cp.b $fileaddr 0x9f050000 $filesize Reboot the board. 2. pepe2k's u-boot_mod Connect the board to ethernet Set up a server with an IP address of 192.168.1.10 Make the openwrt-ath79-generic-qca_ap143-8m-squashfs-factory.bin available via TFTP, as "firmware.bin" run fw_upg Reboot the board. For the 16M version of the board, please use openwrt-ath79-generic-qca_ap143-16m-squashfs-factory.bin Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu> [use fwconcatX names, drop redundant uart status, fix IMAGE_SIZE, set up IMAGE/factory.bin without metadata] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>	2021-06-05 01:17:11 +02:00
Sven Eckelmann	9a172797e5	ath79: Add support for OpenMesh A40 Device specifications: ====================== * Qualcomm/Atheros QCA9558 ver 1 rev 0 * 720/600/240 MHz (CPU/DDR/AHB) * 128 MB of RAM * 16 MB of SPI NOR flash - 2x 7 MB available; but one of the 7 MB regions is the recovery image * 2T2R 2.4 GHz Wi-Fi (11n) * 2T2R 5 GHz Wi-Fi (11ac) * multi-color LED (controlled via red/green/blue GPIOs) * 1x GPIO-button (reset) * external h/w watchdog (enabled by default)) * TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX) * 2x ethernet - eth0 + Label: Ethernet 1 + AR8035 ethernet PHY (RGMII) + 10/100/1000 Mbps Ethernet + 802.3af POE + used as WAN interface - eth1 + Label: Ethernet 2 + AR8035 ethernet PHY (SGMII) + 10/100/1000 Mbps Ethernet + used as LAN interface * 1x USB * internal antennas Flashing instructions: ====================== Various methods can be used to install the actual image on the flash. Two easy ones are: ap51-flash ---------- The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be used to transfer the image to the u-boot when the device boots up. initramfs from TFTP ------------------- The serial console must be used to access the u-boot shell during bootup. It can then be used to first boot up the initramfs image from a TFTP server (here with the IP 192.168.1.21): setenv serverip 192.168.1.21 setenv ipaddr 192.168.1.1 tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr The actual sysupgrade image can then be transferred (on the LAN port) to the device via scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/ On the device, the sysupgrade must then be started using sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin Signed-off-by: Sven Eckelmann <sven@narfation.org>	2021-06-05 01:17:11 +02:00
Sven Eckelmann	eaf2e32c12	ath79: Add support for OpenMesh A60 Device specifications: ====================== * Qualcomm/Atheros QCA9558 ver 1 rev 0 * 720/600/240 MHz (CPU/DDR/AHB) * 128 MB of RAM * 16 MB of SPI NOR flash - 2x 7 MB available; but one of the 7 MB regions is the recovery image * 3T3R 2.4 GHz Wi-Fi (11n) * 3T3R 5 GHz Wi-Fi (11ac) * multi-color LED (controlled via red/green/blue GPIOs) * 1x GPIO-button (reset) * external h/w watchdog (enabled by default)) * TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX) * 2x ethernet - eth0 + Label: Ethernet 1 + AR8035 ethernet PHY (RGMII) + 10/100/1000 Mbps Ethernet + 802.3af POE + used as WAN interface - eth1 + Label: Ethernet 2 + AR8031 ethernet PHY (SGMII) + 10/100/1000 Mbps Ethernet + used as LAN interface * 1x USB * internal antennas Flashing instructions: ====================== Various methods can be used to install the actual image on the flash. Two easy ones are: ap51-flash ---------- The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be used to transfer the image to the u-boot when the device boots up. initramfs from TFTP ------------------- The serial console must be used to access the u-boot shell during bootup. It can then be used to first boot up the initramfs image from a TFTP server (here with the IP 192.168.1.21): setenv serverip 192.168.1.21 setenv ipaddr 192.168.1.1 tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr The actual sysupgrade image can then be transferred (on the LAN port) to the device via scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/ On the device, the sysupgrade must then be started using sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin Signed-off-by: Sven Eckelmann <sven@narfation.org>	2021-06-05 01:17:11 +02:00
Giulio Lorenzo	b108ed0ab0	ath79: add support for ZiKing CPE46B ZiKing CPE46B is a POE outdoor 2.4ghz device with an integrated directional antenna. It is low cost and mostly available via Aliexpress, references can be found at: - https://forum.openwrt.org/t/anddear-ziking-cpe46b-ar9331-ap121/60383 - https://git.lsd.cat/g/openwrt-cpe46b Specifications: - Atheros AR9330 - 32MB of RAM - 8MB of flash (SPI NOR) - 1 * 2.4ghz integrated antenna - 2 * 10/100/1000 ethernet ports (1 POE) - 3 * Green LEDs controlled by the SoC - 3 * Green LEDs controlled via GPIO - 1 * Reset Button controlled via GPIO - 1 * 4 pin serial header on the PCB - Outdoor packaging Flashing instruction: You can use sysupgrade image directly in vendor firmware which is based on OpenWrt/LEDE. In case of issues with the vendor GUI, the vendor Telnet console is vulnerable to command injection and can be used to gain a shell directly on the OEM OpenWrt distribution. Signed-off-by: Giulio Lorenzo <salveenee@mortemale.org> [fix whitespaces, drop redundant uart status and serial0, drop num-chipselects, drop 0x1002 MAC address for wmac] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>	2021-05-17 01:01:32 +02:00
Joao Henrique Albuquerque	4f07966696	ath79: add support for COMFAST CF-E375AC COMFAST CF-E375AC is a ceiling mount AP with PoE support, based on Qualcomm/Atheros QCA9563 + QCA9886 + QCA8337. Short specification: 2x 10/100/1000 Mbps Ethernet, with PoE support 128MB of RAM (DDR2) 16 MB of FLASH 3T3R 2.4 GHz, 802.11b/g/n 2T2R 5 GHz, 802.11ac/n/a, wave 2 built-in 5x 3 dBi antennas output power (max): 500 mW (27 dBm) 1x RGB LED, 1x button built-in watchdog chipset Flash instruction: 1) Original firmware is based on OpenWrt. Use sysupgrade image directly in vendor GUI. 2) TFTP 2.1) Set a tftp server on your machine with a fixed IP address of 192.168.1.10. A place the sysupgrade as firmware_auto.bin. 2.2) boot the device with an ethernet connection on fixed ip route 2.3) wait a few seconds and try to login via ssh 3) TFTP trough Bootloader 3.1) open the device case and get a uart connection working 3.2) stop the autoboot process and test connection with serverip 3.3) name the sysupgrade image firmware.bin and run firmware_upg MAC addresses: Though the OEM firmware has four adresses in the usual locations, it appears that the assigned addresses are just incremented in a different way: interface address location LAN: :DC 0x0 WAN :DD 0x1002 WLAN 2.4g :E6 n/a (0x0 + 10) WLAN 5g :DE 0x6 unused *:DF 0x5006 The MAC address pointed at the label is the one assign to the LAN interface. Signed-off-by: Joao Henrique Albuquerque <joaohccalbu@gmail.com> [add label-mac-device, remove redundant uart status, fix whitespace issues, fix commit message wrapping, remove x bit on DTS file] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>	2021-05-17 01:01:32 +02:00
Michael Pratt	bf8c16dfa2	ath79: set lzma-loader variables to null by default This fixes a small regression where the lzma-loader variable values are being shared between boards that require different configurations. If not set to "" globally, a device without these settings will just take the last values another device has set before in the queue. Fixes: `1b8bd17c2d` ("ath79: lzma-loader: allow setting custom kernel magic") Signed-off-by: Michael Pratt <mcpratt@pm.me> [add detailed explanation to the commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>	2021-05-16 13:05:42 +02:00
Leonardo Mörlein	b993b68b6c	build: introduce $(MKHASH) Before this commit, it was assumed that mkhash is in the PATH. While this was fine for the normal build workflow, this led to some issues if make TOPDIR="$(pwd)" -C "$pkgdir" compile was called manually. In most of the cases, I just saw warnings like this: make: Entering directory '/home/.../package/gluon-status-page' bash: line 1: mkhash: command not found bash: line 1: mkhash: command not found bash: line 1: mkhash: command not found bash: line 1: mkhash: command not found bash: line 1: mkhash: command not found bash: line 1: mkhash: command not found bash: line 1: mkhash: command not found bash: line 1: mkhash: command not found [...] While these were only warnings and the package still compiled sucessfully, I also observed that some package even fail to build because of this. After applying this commit, the variable $(MKHASH) is introduced. This variable points to $(STAGING_DIR_HOST)/bin/mkhash, which is always the correct path. Signed-off-by: Leonardo Mörlein <me@irrelefant.net>	2021-05-13 15:13:15 +02:00
Hauke Mehrtens	5d8ea6d34f	ath79: Deactivate ZyXEL NBG6716 by default The kernel image is too big now and the build fails. WARNING: Image file zyxel_nbg6716-kernel.bin is too big: 4205404 > 4194304 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>	2021-05-02 15:00:40 +02:00
Roger Pueyo Centelles	4387fe00cb	ath79: mikrotik: enable SFP on RB922UAGS-5HPaCD This patch enables the SFP cage on the MikroTik RouterBOARD 922UAGS-5HPacD. GPIO16 (tx-disable-gpios) should be governed by the SFP driver to enable or disable transmission, but no change is observed. Therefore, it is left as output high to ensure the SFP module is forced to transmit. Tested on a RouterBOARD 922UAGS-5HPacD board, with a CISCO GLC-LH-SMD 1310nm module and an unbranded GLC-T RJ45 Gigabit module. PC=>router iperf3 tests deliver 440/300 Mbps up/down, both via regular eth0 port or SFP port with RJ45 module. Bridge between eth0 and eth1 delivers 950 Mbps symmetric. Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>	2021-04-16 13:54:22 +02:00
Michael Pratt	37ea5d9a65	ath79: add factory.bin for ALLNET ALL-WAP02860AC This device is a Senao-based product using hardware and software from Senao with the tar-gz platform for factory.bin and checksum verification at boot time using variables stored in uboot environment and a 'failsafe' image when it fails. Extremely similar hardware/software to Engenius EAP1200H and other Engenius APs with qca955x Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com> Signed-off-by: Michael Pratt <mcpratt@pm.me>	2021-04-08 09:20:59 +02:00
Michael Pratt	d5035f0d26	ath79: add Senao 'failsafe' sysupgrade procedure Use a similar upgrade method for sysupgrade.bin, like factory.bin, for Senao boards with the tar.gz OEM upgrade platform, and 'failsafe' image which is loaded on checksum failure. This is inspired by the OEM upgrade script /etc/fwupgrade.sh and the existing platforms for dual-boot Senao boards. Previously, if the real kernel was damaged or missing the only way to recover was with UART serial console, because the OKLI lzma-loader is programmed to halt. uboot did not detect cases where kernel or rootfs is damaged and boots OKLI instead of the failsafe image, because the checksums stored in uboot environment did not include the real kernel and rootfs space. Now, the stored checksums include the space for both the lzma-loader, kernel, and rootfs. Therefore, these boards are now practically unbrickable. Also, the factory.bin and sysupgrade.bin are now the same, except for image metadata. This allows for flashing OEM image directly from openwrt as well as flashing openwrt image directly from OEM. Make 'loader' partition writable so that it can be updated during a sysupgrade. tested with ENS202EXT v1 EAP1200H EAP350 v1 EAP600 ECB350 v1 ECB600 ENH202 v1 Signed-off-by: Michael Pratt <mcpratt@pm.me>	2021-04-08 09:20:59 +02:00
Michael Pratt	a58cb22bbe	ath79: adjust ath79/tiny Senao APs to 4k blocksize ath79/tiny kernel config has CONFIG_MTD_SPI_NOR_USE_4K_SECTORS=y from commit `05d35403b2` Because of this, these changes are required for 2 reasons: 1. Senao devices in ath79/tiny with a 'failsafe' partition and the tar.gz sysupgrade platform and a flash chip that supports 4k sectors will fail to reboot to openwrt after a sysupgrade. the stored checksum is made with the 64k blocksize length of the image to be flashed, and the actual checksum changes after flashing due to JFFS2 space being formatted within the length of the rootfs from the image example: 0x440000 length of kernel + rootfs (from sysupgrade.bin) 0x439000 offset of rootfs_data (from kernel log) 2. for boards with flash chips that support 4k sectors: saving configuration over sysupgrade is not possible because sysupgrade.tgz is appended at a 64k boundary and the mtd parser starts JFFS2 at a 4k boundary. for boards with flash chips that do not support 4k sectors: partitioning with 4k boundaries causes a boot loop from the mtd parser not finding kernel and rootfs. Also: Some of the Senao boards that belong in ath79/tiny, for example ENH202, have a flash chip that does not support 4k sectors (no SECT_4K symbol in upstream source). Because of this, partitioning must be different for these devices depending on the flash chip model detected by the kernel. Therefore: this creates 2 DTSI files to replace the single one with 64k partitioning for 4k and 64k partitioning respectively. Signed-off-by: Michael Pratt <mcpratt@pm.me>	2021-04-08 09:20:59 +02:00
Michael Pratt	4a0cc5d4ef	ath79: remove 'fakeroot' for Senao devices By using the same custom kernel header magic in both OKLI lzma-loader, DTS, and makefile this hack is not necessary anymore However, "rootfs" size and checksum must now be supplied by the factory.bin image through a script that is accepted by the OEM upgrade script. This is because Senao OEM scripts assume a squashfs header exists at the offset for the original "rootfs" partition which is actually the kernel + rootfs in this implementation, and takes size value from the header that would be there with hexdump, but this offset is now the uImage header instead. This frees up 1 eraseblock previously used by the "fakeroot" partition for bypassing the OEM image verification. Also, these Senao devices with a 'failsafe' partition and the tar-gz factory.bin platform would otherwise require flashing the new tar-gz sysupgrade.bin afterward. So this also prevents having to flash both images when starting from OEM or 'failsafe' the OEM upgrade script verifies the header magic numbers, but only the first two bytes. Example: [ "${magic_word_kernel}" = "2705" ] && [ "${magic_word_rootfs}" = "7371" -o "${magic_word_rootfs}" = "6873" ] && errcode="0" therefore picked the magic number 0x73714f4b which is 'sqOK' Signed-off-by: Michael Pratt <mcpratt@pm.me>	2021-04-08 09:20:59 +02:00
Michael Pratt	1b8bd17c2d	ath79: lzma-loader: allow setting custom kernel magic ...and max flash offset The mtdsplit parser was recently refactored to allow the kernel to have custom image header magic. Let's also do this for the lzma-loader For example: When implemented together, this allows the kernel to "appear" to be a rootfs by OEM software in order to write an image that is actually kernel + rootfs. At the same time, it would boot to openwrt normally by setting the same magic in DTS. Both of the variables have a default value that is unchanged when not defined in the makefiles This has no effect on the size of the loader when lzma compressed. Signed-off-by: Michael Pratt <mcpratt@pm.me>	2021-04-08 09:20:59 +02:00
Mauri Sandberg	bc356de285	ath79: Add support for Buffalo WZR-HP-G300NH This device is a wireless router working on 2.4GHz band based on Qualcom/Atheros AR9132 rev 2 SoC and is accompanied by Atheros AR9103 wireless chip and Realtek RTL8366RB/S switches. Due to two different switches being used also two different devices are provided. Specification: - 400 MHz CPU - 64 MB of RAM - 32 MB of FLASH (NOR) - 3x3:2 2.4 GHz 802.11bgn - 5x 10/100/1000 Mbps Ethernet - 4x LED, 3x button, On/Off slider, Auto/On/Off slider - 1x USB 2.0 - bare UART header place on PCB Flash instruction: - NOTE: Pay attention to the switch variant and choose the image to flash accordingly. (dmesg / kernel logs can tell it) - Methods for flashing - Apply factory image in OEM firmware web-gui. - Sysupgrade on top of existing OpenWRT image - U-Boot TFPT recovery for both stock or OpenWRT images: The device U-boot contains a TFTP server that by default has an address 192.168.11.1 (MAC 02:AA:BB:CC:DD:1A). During the boot there is a time window, during which the device allows an image to be uploaded from a client with address 192.168.11.2. The image will be written on flash automatically. 1) Have a computer with static IP address 192.168.11.2 and the router device switched off. 2) Connect the LAN port next to the WAN port in the device and the computer using a network switch. 3) Assign IP 192.168.11.1 the MAC address 02:AA:BB:CC:DD:1A arp -s 192.168.11.1 02:AA:BB:CC:DD:1A 4) Initiate an upload using TFTP image variant curl -T <imagename> tftp://192.168.11.1 5) Switch on the device. The image will be uploaded subsequently. You can keep an eye on the diag light on the device, it should keep on blinking for a while indicating the writing of the image. General notes: - In the stock firmware the MAC address is the same among all interfaces so it is left here that way too. Recovery: - TFTP method - U-boot serial console Differences to ar71xx platform - This device is split in two different targets now due to hardware being a bit different under the hood. Dynamic solution within the same image is left for later time. - GPIOs for a sliding On/Off switch, marked 'Movie engine' on the device cover, were the wrong way around and were renamed qos_on -> movie_off, qos_off -> movie_on. Associated key codes remained the same they were. The device tree source code is mostly based on musashino's work Signed-off-by: Mauri Sandberg <sandberg@mailfence.com>	2021-03-22 09:23:10 +01:00

1 2 3 4 5 ...

743 Commits