mirror of
https://github.com/openwrt/openwrt.git
synced 2025-01-19 03:06:35 +00:00
ath79: add support for MikroTik RouterBOARD 962UiGS-5HacT2HnT (hAP ac)
This patch adds support for the MikroTik RouterBOARD 962UiGS-5HacT2HnT (hAP ac) Specifications: - SoC: QCA9558 - RAM: 128 MB - Flash: 16 MB SPI - 2.4GHz WLAN: 3x3:3 802.11n on SoC - 5GHz WLAN: 3x3:3 802.11ac on QCA9880 connected via PCIe - Switch: 5x 1000/100/10 on QCA8337 connected via RGMII - SFP cage: connected via SGMII (tested with genuine & generic GLC-T) - USB: 1x type A, GPIO power switch - PoE: Passive input on Ether1, GPIO switched passthrough to Ether5 - Reset button - "SFP" LED connected to SoC - Ethernet LEDs connected to QCA8337 switch - Green WLAN LED connected to QCA9880 Not working: - Red WLAN LED Installation: TFTP boot initramfs image and then perform sysupgrade. Follow common MikroTik procedure as in https://openwrt.org/toh/mikrotik/common. Signed-off-by: Ryan Mounce <ryan@mounce.com.au>
This commit is contained in:
Ryan Mounce
Hauke Mehrtens
parent
fb3f519e59
commit
c2140e32ce
@ -0,0 +1,37 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
|
||||
#include "qca9558_mikrotik_routerboard-96x.dtsi"
|
||||
|
||||
/ {
|
||||
compatible = "mikrotik,routerboard-962uigs-5hact2hnt", "qca,qca9558";
|
||||
model = "MikroTik RouterBOARD 962UiGS-5HacT2HnT (hAP ac)";
|
||||
|
||||
gpio-export {
|
||||
compatible = "gpio-export";
|
||||
|
||||
port5_poe {
|
||||
gpio-export,name = "port5-poe";
|
||||
gpio-export,output = <1>;
|
||||
gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&gpio {
|
||||
input-poe-out-compat {
|
||||
gpio-hog;
|
||||
gpios = <2 GPIO_ACTIVE_HIGH>;
|
||||
input;
|
||||
line-name = "PoE out compat";
|
||||
};
|
||||
};
|
||||
|
||||
&wmac {
|
||||
status = "okay";
|
||||
|
||||
qca,no-eeprom;
|
||||
};
|
||||
|
||||
&pcie1 {
|
||||
status = "okay";
|
||||
};
|
||||
198
target/linux/ath79/dts/qca9558_mikrotik_routerboard-96x.dtsi
Normal file
198
target/linux/ath79/dts/qca9558_mikrotik_routerboard-96x.dtsi
Normal file
@ -0,0 +1,198 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
|
||||
#include "qca955x.dtsi"
|
||||
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
|
||||
/ {
|
||||
aliases {
|
||||
led-boot = &led_user;
|
||||
led-failsafe = &led_user;
|
||||
led-upgrade = &led_user;
|
||||
serial0 = &uart;
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
led_user: user {
|
||||
label = "green:user";
|
||||
gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
|
||||
keys {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
reset {
|
||||
label = "reset";
|
||||
linux,code = <KEY_RESTART>;
|
||||
gpios = <&gpio 20 GPIO_ACTIVE_LOW>;
|
||||
debounce-interval = <60>;
|
||||
};
|
||||
};
|
||||
|
||||
gpio-export {
|
||||
compatible = "gpio-export";
|
||||
|
||||
buzzer {
|
||||
/* Beeper requires PWM for frequency selection */
|
||||
gpio-export,name = "buzzer";
|
||||
gpio-export,output = <0>;
|
||||
gpios = <&gpio 4 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
usb_power {
|
||||
gpio-export,name = "usb-power";
|
||||
gpio-export,output = <0>;
|
||||
gpios = <&gpio 13 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
};
|
||||
|
||||
i2c: i2c {
|
||||
compatible = "i2c-gpio";
|
||||
|
||||
sda-gpios = <&gpio 18 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
|
||||
scl-gpios = <&gpio 19 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
|
||||
i2c-gpio,delay-us = <5>;
|
||||
i2c-gpio,timeout-ms = <1>;
|
||||
};
|
||||
|
||||
sfp1: sfp {
|
||||
compatible = "sff,sfp";
|
||||
|
||||
i2c-bus = <&i2c>;
|
||||
maximum-power-milliwatt = <1000>;
|
||||
los-gpios = <&gpio 21 GPIO_ACTIVE_HIGH>;
|
||||
mod-def0-gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
|
||||
tx-disable-gpios = <&gpio 16 GPIO_ACTIVE_HIGH>;
|
||||
// Toggling GPIO16 actually enables/disables the transmitter,
|
||||
// but the SFP driver does not seem to be using it.
|
||||
};
|
||||
};
|
||||
|
||||
&spi {
|
||||
status = "okay";
|
||||
|
||||
flash@0 {
|
||||
compatible = "jedec,spi-nor";
|
||||
reg = <0>;
|
||||
spi-max-frequency = <40000000>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "RouterBoot";
|
||||
reg = <0x0 0x20000>;
|
||||
read-only;
|
||||
compatible = "mikrotik,routerboot-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "bootloader1";
|
||||
reg = <0x0 0x0>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
hard_config {
|
||||
read-only;
|
||||
};
|
||||
|
||||
bios {
|
||||
size = <0x1000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@10000 {
|
||||
label = "bootloader2";
|
||||
reg = <0x10000 0x0>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
soft_config {
|
||||
};
|
||||
};
|
||||
|
||||
partition@20000 {
|
||||
compatible = "mikrotik,minor";
|
||||
label = "firmware";
|
||||
reg = <0x020000 0xfe0000>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&mdio0 {
|
||||
status = "okay";
|
||||
|
||||
phy0: ethernet-phy@0 {
|
||||
reg = <0>;
|
||||
|
||||
qca,ar8327-initvals = <
|
||||
/* PAD0_MODE from vendor firmware
|
||||
* RGMII_EN, TX/RXCLK_DELAY_EN, TXCLK_DELAY_SEL=1
|
||||
*/
|
||||
0x04 0x07400000 /* PAD0_MODE */
|
||||
0x50 0xc737c737 /* LED_CTRL0 */
|
||||
0x54 0x00000000 /* LED_CTRL1 */
|
||||
0x58 0x00000000 /* LED_CTRL2 */
|
||||
0x5c 0x0030c300 /* LED_CTRL3 */
|
||||
0x7c 0x0000007e /* PORT0_STATUS */
|
||||
>;
|
||||
};
|
||||
};
|
||||
|
||||
ð0 {
|
||||
status = "okay";
|
||||
|
||||
phy-handle = <&phy0>;
|
||||
/* gigabit pll-data from vendor firmware
|
||||
* TX_INVERT, TX_DELAY=3, GIGE, OFFSET_PHASE
|
||||
*/
|
||||
pll-data = <0x8f000000 0x00000101 0x00001616>;
|
||||
|
||||
gmac-config {
|
||||
device = <&gmac>;
|
||||
rgmii-enabled = <1>;
|
||||
};
|
||||
};
|
||||
|
||||
&mdio1 {
|
||||
status = "okay";
|
||||
|
||||
phy_sfp: ethernet-phy@0 {
|
||||
reg = <0>;
|
||||
phy-mode = "sgmii";
|
||||
sfp = <&sfp1>;
|
||||
};
|
||||
};
|
||||
|
||||
ð1 {
|
||||
status = "okay";
|
||||
|
||||
phy-handle = <&phy_sfp>;
|
||||
pll-data = <0x03000000 0x00000101 0x00001616>;
|
||||
qca955x-sgmii-fixup;
|
||||
|
||||
gmac-config {
|
||||
device = <&gmac>;
|
||||
};
|
||||
|
||||
fixed-link {
|
||||
speed = <1000>;
|
||||
full-duplex;
|
||||
};
|
||||
};
|
||||
|
||||
&usb0 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb_phy0 {
|
||||
status = "okay";
|
||||
};
|
||||
@ -38,6 +38,17 @@ define Device/mikrotik_routerboard-922uags-5hpacd
|
||||
endef
|
||||
TARGET_DEVICES += mikrotik_routerboard-922uags-5hpacd
|
||||
|
||||
define Device/mikrotik_routerboard-962uigs-5hact2hnt
|
||||
$(Device/mikrotik_nor)
|
||||
SOC := qca9558
|
||||
DEVICE_MODEL := RouterBOARD 962UiGS-5HacT2HnT (hAP ac)
|
||||
DEVICE_PACKAGES += kmod-ath10k-ct ath10k-firmware-qca988x-ct kmod-usb2 \
|
||||
kmod-i2c-gpio kmod-sfp
|
||||
IMAGE_SIZE := 16256k
|
||||
SUPPORTED_DEVICES += rb-962uigs-5hact2hnt
|
||||
endef
|
||||
TARGET_DEVICES += mikrotik_routerboard-962uigs-5hact2hnt
|
||||
|
||||
define Device/mikrotik_routerboard-lhg-2nd
|
||||
$(Device/mikrotik_nor)
|
||||
SOC := qca9533
|
||||
|
||||
@ -23,6 +23,10 @@ ath79_setup_interfaces()
|
||||
mikrotik,routerboard-wapr-2nd)
|
||||
ucidef_set_interface_lan "eth0"
|
||||
;;
|
||||
mikrotik,routerboard-962uigs-5hact2hnt)
|
||||
ucidef_add_switch "switch0" \
|
||||
"0@eth0" "2:lan" "3:lan" "4:lan" "5:lan" "1:wan"
|
||||
;;
|
||||
*)
|
||||
ucidef_set_interfaces_lan_wan "eth0" "eth1"
|
||||
;;
|
||||
|
||||
@ -34,6 +34,9 @@ case "$FIRMWARE" in
|
||||
mikrotik,routerboard-wap-g-5hact2hnd)
|
||||
caldata_mikrotik_ath9k 0x1000 0x440 $(macaddr_add "$mac_base" 2)
|
||||
;;
|
||||
mikrotik,routerboard-962uigs-5hact2hnt)
|
||||
caldata_mikrotik_ath9k 0x1000 0x440 $(macaddr_add "$mac_base" 7)
|
||||
;;
|
||||
*)
|
||||
caldata_die "board $board is not supported yet"
|
||||
;;
|
||||
|
||||
@ -12,6 +12,7 @@ case "$FIRMWARE" in
|
||||
"ath10k/cal-pci-0000:00:00.0.bin")
|
||||
case $board in
|
||||
mikrotik,routerboard-921gs-5hpacd-15s|\
|
||||
mikrotik,routerboard-962uigs-5hact2hnt|\
|
||||
mikrotik,routerboard-wap-g-5hact2hnd)
|
||||
caldata_sysfsload_from_file $wlan_data 0x5000 0x844
|
||||
;;
|
||||
|
||||
Loading…
Reference in New Issue
Block a user