COMFAST CF-E375AC is a ceiling mount AP with PoE support,
based on Qualcomm/Atheros QCA9563 + QCA9886 + QCA8337.
Short specification:
2x 10/100/1000 Mbps Ethernet, with PoE support
128MB of RAM (DDR2)
16 MB of FLASH
3T3R 2.4 GHz, 802.11b/g/n
2T2R 5 GHz, 802.11ac/n/a, wave 2
built-in 5x 3 dBi antennas
output power (max): 500 mW (27 dBm)
1x RGB LED, 1x button
built-in watchdog chipset
Flash instruction:
1) Original firmware is based on OpenWrt.
Use sysupgrade image directly in vendor GUI.
2) TFTP
2.1) Set a tftp server on your machine with a fixed IP address of
192.168.1.10. A place the sysupgrade as firmware_auto.bin.
2.2) boot the device with an ethernet connection on fixed ip route
2.3) wait a few seconds and try to login via ssh
3) TFTP trough Bootloader
3.1) open the device case and get a uart connection working
3.2) stop the autoboot process and test connection with serverip
3.3) name the sysupgrade image firmware.bin and run firmware_upg
MAC addresses:
Though the OEM firmware has four adresses in the usual locations,
it appears that the assigned addresses are just incremented in a
different way:
interface address location
LAN: *:DC 0x0
WAN *:DD 0x1002
WLAN 2.4g *:E6 n/a (0x0 + 10)
WLAN 5g *:DE 0x6
unused *:DF 0x5006
The MAC address pointed at the label is the one assign to the LAN
interface.
Signed-off-by: Joao Henrique Albuquerque <joaohccalbu@gmail.com>
[add label-mac-device, remove redundant uart status, fix whitespace
issues, fix commit message wrapping, remove x bit on DTS file]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Ubiquiti EdgeRouter 6P is 6 port router with similar
specifications as the EdgeRouter 4, support for which was added
in commit dd651e54cc
There are five 10/100/1000 Mbps RJ/Copper ports and
one 1000 Mbps SFP port.
SoC: Octeon Cavium 7130 (Cavium 3) at 1000MHz
Memory: 1GiB DDR3
Flash: 2x2M chips with uboots (chainloaded) + 512K eeprom
LEDs: 1x for power status (white/blue, controllable)
and 6x for ethernet and SFP ports (no control over them)
Buttons: 1x Reset
Serial: 1x RJ45 port on front panel. 115200 baud, 8N1
USB: 1x USB3.0 on front panel
MII: 1x QSGMII from SoC
PHY: 1x Vitesse VSC8504 of which 4 ports are used (phys 4-7)
1x Vitesse VSC8514 of which 2 ports are used (phys 8-9)
Network port mapping
- eth0 on device maps to lan0 and phy5
- eth1 on device maps to lan1 and phy6
- eth2 on device maps to lan2 and phy7
- eth3 on device maps to lan3 and phy8
- eth4 on device maps to lan4 and phy9
- eth5 (SFP) on device maps to lan5 and phy4
What is not working:
- There is no port status available before it goes up
- SFP have no additional status and presented as no different from eth
- Power-over-ethernet (passive) support has not been tested
How to flash the firmware:
- copy openwrt-octeon-ubnt_edgerouter-6p-initramfs-kernel.bin and
openwrt-octeon-ubnt_edgerouter-6p-squashfs-sysupgrade.tar to
USB flash drive that is formatted to vfat/fat32
- connect USB flash drive to EdgeRouter 6P front USB port
- connect serial cable using front RJ45 port (115200 baud, 8N1)
- connect power to cable to EdgeRouter 6P
- connect terminal to the console to see uboot boot process
- interrupt boot by pressing button(s) on your keyboard to log
in to the uboot
- detect usb connected flash drives by typing to the console:
usb start
- after drive is detected load initramfs+kernel to the memory by typing:
fatload usb 0:1 0x20000000 openwrt-octeon-ubnt_edgerouter-6p-initramfs-kernel.bin
- after initramfs+kernel is loaded to the memory load it by typing:
bootoctlinux 0 numcores=4 endbootargs mem=0
- boot process should finish and you will be greeted with console
after pressing enter
- create directory to mount usb flash drive to by typing:
mkdir /tmp/sda
- mount flash drive to that directory by typing:
mount /dev/sda1 /tmp/sda
- flash firmware to router internal storage by typing:
sysupgrade /tmp/sda/openwrt-octeon-ubnt_edgerouter-6p-squashfs-sysupgrade.tar
- device will reboot and after it gets up you will have
edgerouter 6p running openwrt
Signed-off-by: Dan Brown <danbrown@gmail.com>
[reorder/squash patches, move ethernet@0 to DTS, share image setup]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
EdgeRouter 4 and upcoming EdgeRouter 6P and 12 have similar setup,
so create a shared DTSI to prevent duplicate code.
Signed-off-by: Dan Brown <danbrown@gmail.com>
[reorder/squash commits, add description, move ethernet@0 to DTS]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Remove vn call in favour of v call. This commit serves as preparation
for removing the v function call.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
[alter slightly to prevent double space after colon]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Vendor firmware expects model name without manufacturer name inside
'supported_devices' part of metadata. This allows direct upgrade to
OpenWrt from vendor's GUI.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
This fixes a small regression where the lzma-loader variable values
are being shared between boards that require different configurations.
If not set to "" globally, a device without these settings will just take
the last values another device has set before in the queue.
Fixes: 1b8bd17c2d ("ath79: lzma-loader: allow setting custom kernel magic")
Signed-off-by: Michael Pratt <mcpratt@pm.me>
[add detailed explanation to the commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
When building GRUB with binutils 2.35.2 or later, an error occurs due to
a section .note.gnu.property that is placed at an offset such that
objcopy needs to pad the img file with zeros. This in turn causes the
following error: "error: Decompressor is too big.".
The fix accepted by upstream patches a python script that isn't executed
at all when building GRUB with OpenWrt buildroot. There's another patch
that patches the files generated by that python script directly, but by
including it we would deviate further from upstream. Instead of doing
that, simply bump to the latest release candidate.
As one of the fixes for the CVEs causes grub to crash on some x86
hardware using legacy BIOS when compiled with -O2, filter -O2 and
-O3 out of TARGET_CFLAGS.
Fixes the following CVEs:
- CVE-2020-14372
- CVE-2020-25632
- CVE-2020-25647
- CVE-2020-27749
- CVE-2020-27779
- CVE-2021-3418
- CVE-2021-20225
- CVE-2021-20233
Runtime-tested on x86/64.
Fixes: FS#3790
Suggested-by: Dirk Neukirchen <plntyk.lede@plntyk.name>
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
c44b40b overlay: fix syncronizing typo
b5397a1 fstools: block: fix segfault on mount with no target
bd7cc8d block: use dynamically allocated target string
6d8450e blockd: use allocated strings instead of fixed buffers
d47909e libblkid-tiny: fix buffer overflow
67d2297 block: match device path instead of assuming /dev/%s
2aeba88 block: allow autofs and umount commands also on MTD/UBI
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
28b162366d09 mt76: fix calling mt76_get_of_eeprom with an offset for pre-cal data
9d736545bb5a mt76: mt7915: disable pre-calibration support for now
Signed-off-by: Felix Fietkau <nbd@nbd.name>
6a6011d uclient-http: set eof mark when content-length is 0
19571e4 tests: fix help usage test for uclient built with sanitizer
c5fc04b tests: fix help usage test
Signed-off-by: Baptiste Jonglez <git@bitsofnetworks.org>
PREFER_IPV4_ADDRESS is broken on IPv6-only hosts, as it causes busybox
utilities (ping, traceroute, ntpd) to forcibly use the A record instead of
the AAAA record when resolving a DNS name. This obviously fails when
there is no IPv4 connectivity. Since IPv6-only hosts or routers will only
become more common over time, disable PREFER_IPV4_ADDRESS to support this
use-case.
As a side-effect, disabling PREFER_IPV4_ADDRESS changes the default
resolution behaviour of busybox utilities on dual-stack hosts. Busybox
utilities now simply use the order given by getaddrinfo(), so they will
now prefer IPv6 addresses when resolving a name with both A and AAAA
records if there is IPv6 connectivity. This is in line with RFC 6724.
PREFER_IPV4_ADDRESS was likely intended to work around naive
implementations of getaddrinfo() that could return AAAA records first,
even on an IPv4-only host. But both musl (since 1.1.3) and glibc
correctly implement RFC 6724 for getaddrinfo() and check connectivity to
determine the correct order in which to return records. On IPv4-only
hosts, getaddrinfo() will return A records first, so there is no need for
the PREFER_IPV4_ADDRESS hack.
See also: https://bugs.busybox.net/show_bug.cgi?id=12381
Fixes: FS#84
Fixes: FS#2608
References: https://github.com/openwrt/openwrt/pull/4167
Signed-off-by: Alexander Traud <pabstraud@compuserve.com>
Signed-off-by: Baptiste Jonglez <git@bitsofnetworks.org>
Before this commit, it was assumed that mkhash is in the PATH. While
this was fine for the normal build workflow, this led to some issues if
make TOPDIR="$(pwd)" -C "$pkgdir" compile
was called manually. In most of the cases, I just saw warnings like this:
make: Entering directory '/home/.../package/gluon-status-page'
bash: line 1: mkhash: command not found
bash: line 1: mkhash: command not found
bash: line 1: mkhash: command not found
bash: line 1: mkhash: command not found
bash: line 1: mkhash: command not found
bash: line 1: mkhash: command not found
bash: line 1: mkhash: command not found
bash: line 1: mkhash: command not found
[...]
While these were only warnings and the package still compiled sucessfully,
I also observed that some package even fail to build because of this.
After applying this commit, the variable $(MKHASH) is introduced. This
variable points to $(STAGING_DIR_HOST)/bin/mkhash, which is always the
correct path.
Signed-off-by: Leonardo Mörlein <me@irrelefant.net>
Fixes following error while executing the init script on the buildhost:
Enabling boot
./etc/init.d/bootcount: line 5: /lib/upgrade/asrock.sh: No such file or directory
Enabling bootcount
While at it fix following shellcheck issue:
base-files/etc/init.d/bootcount line 11:
if [ $? -eq 0 ]; then
^-- SC2181: Check exit code directly with e.g. 'if mycmd;', not indirectly with $?.
Cc: Ansuel Smith <ansuelsmth@gmail.com>
Cc: Pawel Dembicki <paweldembicki@gmail.com>
Cc: Christian Lamparter <chunkeey@gmail.com>
Fixes: 98b86296e6 ("ipq806x: add support for ASRock G10")
References: https://gitlab.com/ynezz/openwrt/-/jobs/1243290743#L1444
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Includes fix for CVE-2020-24588
c7dd54a22e30 mt76: connac: skip wtbl reset on sta disconnect
3511fd430356 mt76: validate rx A-MSDU subframes
aedc3145de6e mt76: fix possible NULL pointer dereference in mt76_tx
5c2baab92cd0 mt76: mt7615: fix NULL pointer dereference in tx_prepare_skb()
af21659ee834 mt76: mt76x0: use dev_debug instead of dev_err for hw_rf_ctrl
e423c16f16f7 mt76: mt7615: free irq if mt7615_mmio_probe fails
f2d0da8da9b7 mt76: mt7663: enable hw rx header translation
d2713a5d9de9 mt76: mt7921: fix mt7921_wfsys_reset sequence
ce5f32d84f33 mt76: mt7921: Don't alter Rx path classifier
8ab8c7747197 mt76: connac: fw_own rely on all packet memory all being free
a747b0bb4956 mt76: mt7921: enable deep sleep at runtime
2e6e999509b1 mt76: mt7921: add deep sleep control to runtime-pm knob
30bcb2338ce2 mt76: connac: fix WoW with disconnetion and bitmap pattern
56518f4a126e mt76: mt7921: consider the invalid value for to_rssi
e969ab10a034 mt76: mt7921: add back connection monitor support
Signed-off-by: Felix Fietkau <nbd@nbd.name>
From the patch series description:
Several security issues in the 802.11 implementations were found by
Mathy Vanhoef (New York University Abu Dhabi), who has published all
the details at
https://papers.mathyvanhoef.com/usenix2021.pdf
Specifically, the following CVEs were assigned:
* CVE-2020-24586 - Fragmentation cache not cleared on reconnection
* CVE-2020-24587 - Reassembling fragments encrypted under different
keys
* CVE-2020-24588 - Accepting non-SPP A-MSDU frames, which leads to
payload being parsed as an L2 frame under an
A-MSDU bit toggling attack
* CVE-2020-26139 - Forwarding EAPOL from unauthenticated sender
* CVE-2020-26140 - Accepting plaintext data frames in protected
networks
* CVE-2020-26141 - Not verifying TKIP MIC of fragmented frames
* CVE-2020-26142 - Processing fragmented frames as full frames
* CVE-2020-26143 - Accepting fragmented plaintext frames in
protected networks
* CVE-2020-26144 - Always accepting unencrypted A-MSDU frames that
start with RFC1042 header with EAPOL ethertype
* CVE-2020-26145 - Accepting plaintext broadcast fragments as full
frames
* CVE-2020-26146 - Reassembling encrypted fragments with non-consecutive
packet numbers
* CVE-2020-26147 - Reassembling mixed encrypted/plaintext fragments
In general, the scope of these attacks is that they may allow an
attacker to
* inject L2 frames that they can more or less control (depending on the
vulnerability and attack method) into an otherwise protected network;
* exfiltrate (some) network data under certain conditions, this is
specific to the fragmentation issues.
A subset of these issues is known to apply to the Linux IEEE 802.11
implementation (mac80211). Where it is affected, the attached patches
fix the issues, even if not all of them reference the exact CVE IDs.
In addition, driver and/or firmware updates may be necessary, as well
as potentially more fixes to mac80211, depending on how drivers are
using it.
Specifically, for Intel devices, firmware needs to be updated to the
most recently released versions (which was done without any reference
to the security issues) to address some of the vulnerabilities.
To have a single set of patches, I'm also including patches for the
ath10k and ath11k drivers here.
We currently don't have information about how other drivers are, if
at all, affected.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
When building for MikroTik devices the kernel2minor tool will sometimes
fail with:
Can't get lstat from kernel file!: No such file or directory.
This is because kernel2minor expects paths no longer than 250 chars.
To work around this the include/image-commands.mk has been modified
to copy the kernel to a temporary file (/tmp/tmp.XXXXXXXXXX) before
calling kernel2minor.
Signed-off-by: François Chavant <francois@chavant.info>
Add support for querying and parsing SRV DNS records to nslookup_lede.c
This patch is based on http://lists.busybox.net/pipermail/busybox/2019-June/087359.html
Signed-off-by: Perry Melange <isprotejesvalkata@gmail.com>
[reword subject, bump PKG_RELEASE]
Signed-off-by: Paul Spooren <mail@aparcar.org>
When the list of packages to be installed in a built image exceeds a certain
number, then 'opkg install' executed for target '$(curdir)/install' in
package/Makefile fails with: /usr/bin/env: Argument list too long.
On Linux, the length of a command-line parameter is limited by
MAX_ARG_STRLEN to max 128 kB.
* https://elixir.bootlin.com/linux/latest/source/include/uapi/linux/binfmts.h#L15
* https://www.in-ulm.de/~mascheck/various/argmax/
To solve the problem, store the package list being passed to 'opkg install'
in a temporary file and use the shell command substitution to pass the
content of the file to 'opkg install'. This guarantees that the length of
the command-line parameters passed to the bash shell is short.
The following bash script demonstrates the problem:
----------------------------------------------------------------------------
count=${1:-1000}
FILES=""
a_file="/home/egorenar/Repositories/openwrt-rel/bin/targets/alpine/generic/packages/base-files_1414-r16464+19-e887049fbb_arm_cortex-a15_neon-vfpv4.ipk"
for i in $(seq 1 $count); do
FILES="$FILES $a_file"
done
env bash -c "echo $FILES >/dev/null"
echo "$FILES" | wc -c
----------------------------------------------------------------------------
Test run:
----------------------------------------------------------------------------
$ ./test.sh 916
130989
$ ./test.sh 917
./test.sh: line 14: /bin/env: Argument list too long
131132
----------------------------------------------------------------------------
Signed-off-by: Alexander Egorenkov <egorenar-dev@posteo.net>
[reword commit subject]
Signed-off-by: Paul Spooren <mail@aparcar.org>
The allows userspace LEDs to be created and controlled. This can be useful
for testing triggers and can also be used to implement virtual LEDs.
Signed-off-by: Keith T. Garner <kgarner@kgarner.com>
[squash fixup commit and improve option wording]
Signed-off-by: Paul Spooren <mail@aparcar.org>
The code uses get_mtd_device_nm() which must be followed by a call to
put_mtd_device() once the handle is no longer used.
This fixes spurious shutdown console messages such as:
[ 2256.334562] Removing MTD device #7 (soft_config) with use count 1
Reported-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
311-MIPS-zboot-put-appended-dtb-into-a-section.patch
commit d2e850e96183 in kernel, part of v5.11
499-mtd-don-t-lock-when-recursively-deleting-partitions.patch
commit cb4543054c5c in kernel, part of v5.13
103-MIPS-select-CPU_MIPS64-for-remaining-MIPS64-CPUs.patch
commit 5a4fa44f5e1b in kernel, part of v5.13
Move them to backports folder to make maintainance easier.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
MAC addresses read from official firmware
value location
Wlan xx 71 de factory@0x04
Lan xx 71 dd factory@0x28
Wan xx 71 df factory@0x2e
Label xx 71 dd factory@0x28
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
[fix sorting in 02_network, redact commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
186af01047b2 mt76: mt7921: introduce MCU_EVENT_LP_INFO event parsing
93b5c28c97d5 mt76: mt7921: add rcu section in mt7921_mcu_tx_rate_report
a8e89c5a1d1f mt76: testmode: add support to send larger packet
a0cc9a9e3877 mt76: mt7915: rework mt7915_tm_set_tx_len()
c8b96630324e mt76: mt7915: fix rate setting of tx descriptor in testmode
22fd2958c42a mt76: mt7615: fix memleak when mt7615_unregister_device()
7401e0db3143 mt76: mt7915: fix memleak when mt7915_unregister_device()
c3656268b3f6 mt76: mt7915: only free skbs after mt7915_dma_reset() when reset happens
0ce955b04ba8 mt76: mt7615: only free skbs after mt7615_dma_reset() when reset happens
b03d1e62acf7 mt76: mt7615: use ieee80211_free_txskb() in mt7615_tx_token_put()
5ac02e22fb03 mt76: flush tx status queue on DMA reset
c71f609b398a mt76: sync with upstream changes
23ecadd4af77 mt76: mt7615: fix hardware error recovery for mt7663
57a899ee3c3c mt76: mt7615: fix entering driver-own state on mt7663
42a2dddb706b mt76: mt7615: load ROM patch before checking patch semaphore status
cf0e406af84a mt76: mt7915: add support for applying pre-calibration data
459940ccbc58 mt76: mt7921: move hw configuration in mt7921_register_device
0a094b11f3c0 mt76: improve mcu error logging
bf536832e37d mt76: mt7921: run mt7921_mcu_fw_log_2_host holding mt76 mutex
7616f4f78163 mt76: mt7921: add wifisys reset support in debugfs
e620bd881ef5 mt76: mt7921: abort uncompleted scan by wifi reset
e8dacf59ab1c mt76: mt7915: rework the flow of txpower setting
c8c78e577236 mt76: mt7915: directly read per-rate tx power from registers
1622bf4f8705 mt76: mt7921: add mt7921_dma_cleanup in mt7921_unregister_device
ef96fafad8a9 mt76: Convert to DEFINE_SHOW_ATTRIBUTE
90e4bfea2948 mt76: mt7921: do not use 0 as NULL pointer
0a139d7f5966 mt76: connac: move mcu_update_arp_filter in mt76_connac module
de26c73ce3c2 mt76: mt7921: remove leftover function declaration
1c0b6cb4f942 mt76: mt7921: fix a race between mt7921_mcu_drv_pmctrl and mt7921_mcu_fw_pmctrl
2923e3e2b8e4 mt76: mt7663: fix a race between mt7615_mcu_drv_pmctrl and mt7615_mcu_fw_pmctrl
74d0fdaa7a99 mt76: connac: introduce wake counter for fw_pmctrl synchronization
28c87e09a5ea mt76: mt7921: rely on mt76_connac_pm_ref/mt76_connac_pm_unref in tx path
36f664edc7db mt76: mt7663: rely on mt76_connac_pm_ref/mt76_connac_pm_unref in tx path
51b3d1a9a2b7 mt76: dma: add the capability to define a custom rx napi poll routine
4f1339c9fb72 mt76: mt7921: rely on mt76_connac_pm_ref/mt76_connac_pm_unref in tx/rx napi
1bc5e67a60be mt76: mt7663: rely on mt76_connac_pm_ref/mt76_connac_pm_unref in tx/rx napi
325f7b451c03 mt76: connac: unschedule ps_work in mt76_connac_pm_wake
12115052a02f mt76: connac: check wake refcount in mcu_fw_pmctrl
e5d28e3cef66 mt76: connac: remove MT76_STATE_PM in mac_tx_free
475112a3cdcc mt76: mt7921: get rid of useless MT76_STATE_PM in mt7921_mac_work
112998f32d85 mt76: connac: alaways wake the device before scanning
4334f3e2fc43 mt76: mt7615: rely on pm refcounting in mt7615_led_set_config
0562380659ad mt76: connac: do not run mt76_txq_schedule_all directly
acfa78df5708 mt76: connac: use waitqueue for runtime-pm
ca74a4cd0722 mt76: remove MT76_STATE_PM in tx path
0c2d3e74852e mt76: mt7921: add awake and doze time accounting
45e0eefffe9f mt76: mt7921: enable sw interrupts
fd2ff641166f mt76: mt7615: Fix a dereference of pointer sta before it is null checked
7e2521468767 mt76: mt7921: move mt7921_dma_reset in dma.c
c9dd6b1fa171 mt76: mt7921: introduce mt7921_wpdma_reset utility routine
2ac7c7e9c568 mt76: mt7921: introduce mt7921_dma_{enable,disable} utilities
662a89f2b9d1 mt76: mt7921: introduce mt7921_wpdma_reinit_cond utility routine
614efe9e9180 mt76: connac: introduce mt76_connac_mcu_set_deep_sleep utility
0dbb16ef39d8 mt76: mt7921: enable deep sleep when the device suspends
3c19f569cc70 mt76: mt7921: fix possible invalid register access
ade1f5aad4c6 mt76: move token_lock, token and token_count in mt76_dev
8d5c456be1ff mt76: move token utilities in mt76 common module
fb04d9df5e52 mt76: mt7915: do not read rf value from efuse in flash mode
2126b2176336 mt76: mt7921: get rid of mcu_reset function pointer
d325b7eff1b1 mt76: mt7921: improve doze opportunity
2ae25c7e547e mt76: mt7663: add awake and doze time accounting
349bbb9d6f13 mt76: connac: unschedule mac_work before going to sleep
98a235004dea mt76: mt7921: mt7921_stop should put device in fw_own state
63d80b9ab251 mt76: mt7921: introduce mt7921_mcu_sta_add routine
3c5bf837fdbd mt76: mt7615: fix a precision vs width bug in printk
ded14da5eacc mt76: mt7915: fix a precision vs width bug in printk
aaf0d254f9ea mt76: mt7921: fix a precision vs width bug in printk
757af5c67d32 mt76: move mt76_token_init in mt76_alloc_device
ed41ed73a495 mt76: mt7921: reinit wpdma during drv_own if necessary
92fb81e085c6 mt76: mt7921: fix possible AOOB issue in mt7921_mcu_tx_rate_report
53d915a23bc9 mt76: connac: do not schedule wake_work if the runtime-pm is disabled
23fe1bdcf15a mt76: connac: do not schedule mac_work if the device is not running
e5b19336c58e mt76: mt7615: do not set MT76_STATE_PM at bootstrap
0fc2136a61dd mt76_connac_mcu: move mt76_connac_mcu_update_arp_filter outside of CONFIG_PM
e693f3e23e06 mt76: mt7915: add MSI support
5231e7300fa4 mt7915: disable ASPM
554b50dabf54 mt76: connac: fix uninitialized HT A-MPDU setting field in STA_REC_PHY
43b9c0a838bb mt76: mt7921: fix max aggregation subframes setting
5a387a0a3004 mt76: mt7921: enable rx hw de-amsdu
c8cbcb87be07 mt76: connac: add missing configuration in mt76_connac_mcu_wtbl_hdr_trans_tlv
55921e57b380 mt76: mt7921: enable rx header traslation offload
01441f67d8b2 mt76: mt7921: enable rx csum offload
c9ab76dd93a0 mt76: mt7915: move mt7915_queue_rx_skb to mac.c
caedb4c4ee41 mt76: mt7615: fix fixed-rate tx status reporting
c6ae95d43e6d mt76: improve tx status codepath
27d468d094e6 mt76: mt7915: rework tx rate reporting
3b4ca5b09e2c mt76: mt7615: avoid use of ieee80211_tx_info_clear_status
e1f07d7f1cb9 mt76: mt7603: avoid use of ieee80211_tx_info_clear_status
18513ba5fbc2 mt76: mt7915: add support for tx status reporting
35f189cf81b2 mt76: mt7915: fix uninitialized variable in MSI error handling
9e928ac1ea9b mt76: dma: use ieee80211_tx_status_ext to free packets when tx fails
628eee9c386c mt76: fill queue entry wcid for all skbs with a station
a9bc4d94b7a1 mt76: intialize tx queue entry wcid to 0xffff by default
998ca8af7d17 mt76: mt7915: fix tssi indication field of DBDC NICs
7dd24b3cfacf mt76: mt7915: fix a signedness bug in mt7915_mcu_apply_tx_dpd()
535025d65d8d mt76: mt7915: cleanup mt7915_mcu_sta_rate_ctrl_tlv()
ff8bbe22dd87 mt76: mt7915: add .set_bitrate_mask() callback
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The previous commit bumped the source commit level without reflecting
that in PKG_SOURCE_DATA. Bump PKG_SOURCE_DATA as well.
Fixes: 97e820c6d6 ("rpcd: update to latest HEAD")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This adds the CPU port to the unknown multicast flooding port mask,
which fixes the VLAN issues introduced by the multicast group patches
Tested-by: Russell Senior <russell@personaltelco.net> [Netgear GS108Tv3]
Signed-off-by: Birger Koblitz <mail@birger-koblitz.de>
Signed-off-by: Bjørn Mork <bjorn@mork.no> [whitespace fix]
Signed-off-by: Petr Štetiar <ynezz@true.cz> [unknwon typo fix]
The ZyXEL NR7101 is an 802.3at PoE powered 5G outdoor (IP68) CPE
with integrated directional 5G/LTE antennas.
Specifications:
- SoC: MediaTek MT7621AT
- RAM: 256 MB
- Flash: 128 MB MB NAND (MX30LF1G18AC)
- WiFi: MediaTek MT7603E
- Switch: 1 LAN port (Gigabiti)
- 5G/LTE: Quectel RG502Q-EA connected by USB3 to SoC
- SIM: 2 micro-SIM slots under transparent cover
- Buttons: Reset, WLAN under same cover
- LEDs: Multicolour green/red/yellow under same cover (visible)
- Power: 802.3at PoE via LAN port
The device is built as an outdoor ethernet to 5G/LTE bridge or
router. The Wifi interface is intended for installation and/or
temporary management purposes only.
UART Serial:
57600N1
Located on populated 5 pin header J5:
[o] GND
[ ] key - no pin
[o] RX
[o] TX
[o] 3.3V Vcc
Remove the SIM/button/LED cover, the WLAN button and 12 screws
holding the back plate and antenna cover together. The GPS antenna
is fixed to the cover, so be careful with the cable. Remove 4
screws fixing the antenna board to the main board, again being
careful with the cables.
A bluetooth TTL adapter is recommended for permanent console
access, to keep the router water and dustproof. The 3.3V pin is
able to power such an adapter.
MAC addresses:
OpenWrt OEM Address Found as
lan eth2 08:26:97:*:*:BC Factory 0xe000 (hex), label
wlan0 ra0 08:26:97:*:*:BD Factory 0x4 (hex)
wwan0 usb0 random
WARNING!!
ISP managed firmware might at any time update itself to a version
where all known workarounds have been disabled. Never boot an ISP
managed firmware with a SIM in any of the slots if you intend to use
the router with OpenWrt. The bootloader lock can only be disabled with
root access to running firmware. The flash chip is physically
inaccessible without soldering.
Installation from OEM web GUI:
- Log in as "supervisor" on https://172.17.1.1/
- Upload OpenWrt initramfs-recovery.bin image on the
Maintenance -> Firmware page
- Wait for OpenWrt to boot and ssh to root@192.168.1.1
- (optional) Copy OpenWrt to the recovery partition. See below
- Sysupgrade to the OpenWrt sysupgrade image and reboot
Installation from OEM ssh:
- Log in as "root" on 172.17.1.1 port 22022
- scp OpenWrt initramfs-recovery.bin image to 172.17.1.1:/tmp
- Prepare bootloader config by running:
nvram setro uboot DebugFlag 0x1
nvram setro uboot CheckBypass 0
nvram commit
- Run "mtd_write -w write initramfs-recovery.bin Kernel" and reboot
- Wait for OpenWrt to boot and ssh to root@192.168.1.1
- (optional) Copy OpenWrt to the recovery partition. See below
- Sysupgrade to the OpenWrt sysupgrade image and reboot
Copying OpenWrt to the recovery partition:
- Verify that you are running a working OpenWrt recovery image
from flash
- ssh to root@192.168.1.1 and run:
fw_setenv CheckBypass 0
mtd -r erase Kernel2
- Wait while the bootloader mirrors Image1 to Image2
NOTE: This should only be done after successfully booting the OpenWrt
recovery image from the primary partition during installation. Do
not do this after having sysupgraded OpenWrt! Reinstalling the
recovery image on normal upgrades is not required or recommended.
Installation from Z-Loader:
- Halt boot by pressing Escape on console
- Set up a tftp server to serve the OpenWrt initramfs-recovery.bin
image at 10.10.10.3
- Type "ATNR 1,initramfs-recovery.bin" at the "ZLB>" prompt
- Wait for OpenWrt to boot and ssh to root@192.168.1.1
- Sysupgrade to the OpenWrt sysupgrade image
NOTE: ATNR will write the recovery image to both primary and recovery
partitions in one go.
Booting from RAM:
- Halt boot by pressing Escape on console
- Type "ATGU" at the "ZLB>" prompt to enter the U-Boot menu
- Press "4" to select "4: Entr boot command line interface."
- Set up a tftp server to serve the OpenWrt initramfs-recovery.bin
image at 10.10.10.3
- Load it using "tftpboot 0x88000000 initramfs-recovery.bin"
- Boot with "bootm 0x8800017C" to skip the 380 (0x17C) bytes ZyXEL
header
This method can also be used to RAM boot OEM firmware. The warning
regarding OEM applies! Never boot an unknown OEM firmware, or any OEM
firmware with a SIM in any slot.
NOTE: U-Boot configuration is incomplete (on some devices?). You may
have to configure a working mac address before running tftp using
"setenv eth0addr <mac>"
Unlocking the bootloader:
If you are unebale to halt boot, then the bootloader is locked.
The OEM firmware locks the bootloader on every boot by setting
DebugFlag to 0. Setting it to 1 is therefore only temporary
when OEM firmware is installed.
- Run "nvram setro uboot DebugFlag 0x1; nvram commit" in OEM firmware
- Run "fw_setenv DebugFlag 0x1" in OpenWrt
NOTE:
OpenWrt does this automatically on first boot if necessary
NOTE2:
Setting the flag to 0x1 avoids the reset to 0 in known OEM
versions, but this might change.
WARNING:
Writing anything to flash while the bootloader is locked is
considered extremely risky. Errors might cause a permanent
brick!
Enabling management access from LAN:
Temporary workaround to allow installing OpenWrt if OEM firmware
has disabled LAN management:
- Connect to console
- Log in as "root"
- Run "iptables -I INPUT -i br0 -j ACCEPT"
Notes on the OEM/bootloader dual partition scheme
The dual partition scheme on this device uses Image2 as a recovery
image only. The device will always boot from Image1, but the
bootloader might copy Image2 to Image1 under specific conditions. This
scheme prevents repurposing of the space occupied by Image2 in any
useful way.
Validation of primary and recovery images is controlled by the
variables CheckBypass, Image1Stable, and Image1Try.
The bootloader sets CheckBypass to 0 and reboots if Image1 fails
validation.
If CheckBypass is 0 and Image1 is invalid then Image2 is copied to
Image1.
If CheckBypass is 0 and Image2 is invalid, then Image1 is copied to
Image2.
If CheckBypass is 1 then all tests are skipped and Image1 is booted
unconditionally. CheckBypass is set to 1 after each successful
validation of Image1.
Image1Try is incremented if Image1Stable is 0, and Image2 is copied to
Image1 if Image1Try is 3 or larger. But the bootloader only tests
Image1Try if CheckBypass is 0, which is impossible unless the booted
image sets it to 0 before failing.
The system is therefore not resilient against runtime errors like
failure to mount the rootfs, unless the kernel image sets CheckBypass
to 0 before failing. This is not yet implemented in OpenWrt.
Setting Image1Stable to 1 prevents the bootloader from updating
Image1Try on every boot, saving unnecessary writes to the environment
partition.
Keeping an OpenWrt initramfs recovery as Image2 is recommended
primarily to avoid unwanted OEM firmware boots on failure. Ref the
warning above. It enables console-less recovery in case of some
failures to boot from Image1.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
The ZyXEL NR7101 prepend an additional header to U-Boot images. This
header use the TRX magic 0x30524448 (HDR0), but is incompatible with
TRX images.
This code is reverse-engineered based on matching 32 bit numbers
found in the header with lengths and different checksum
calculations of the vendor images found on the device. The result
was matched against the validation output produced by the
bootloader to name the associated header fields.
Example bootloader validation output:
Zyxel TRX Image 1 --> Found! Header Checksum OK
============ZyXEL header information==================
chipId : MT7621A
boardId : NR7101
modelId : 07 01 00 01
kernel_len : (14177560)
kernelChksum : (0x8DD31F69)
swVersionInt : 1.00(ABUV.0)D1
swVersionExt : 1.00(ABUV.0)D1
Zyxel TRX Image 2 --> Found! Header Checksum OK
============ZyXEL header information==================
chipId : MT7621A
boardId : NR7101
modelId : 07 01 00 01
kernel_len : (14176660)
kernelChksum : (0x951A7637)
swVersionInt : 1.00(ABUV.0)D0
swVersionExt : 1.00(ABUV.0)D0
=================================================
Check image validation:
Image1 Header Magic Number --> OK
Image2 Header Magic Number --> OK
Image1 Header Checksum --> OK
Image2 Header Checksum --> OK
Image1 Data Checksum --> OK
Image2 Data Checksum --> OK
Image1 Stable Flag --> Stable
Image1 Try Counter --> 0
Image1: OK
Image2: OK
The coverage and algorithm for the kernelChksum field is unknown.
This field is not validated by the bootloader or the OEM firmware
upgrade tool. It is therefore set to a static value for now.
The swVersion fields contain free form string values. The OEM firmware
use ZyXEL structured version numbers as shown above. The strings are
not interpreted or validated on boot, so they can be repurposed for
anything we want the bootloader to display to the user. But the OEM
web GUI fails to flash images with freeform strings.
The purpose of the other strings in the header is not known. The
values appear to be static. We assume they are fixed for now, until
we have other examples. One of these strings is the platform name,
which is taken as an input parameter for support other members of
the device family.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
ath79, lantiq, ipq40xx, ramips all use the OpenWrt-specific gpio-export
functionality. Consolidate the patch that adds it under hack-5.10 since
this logic is obviously not target-specific. For those who want to
disable it, unsetting CONFIG_GPIO_SYSFS symbol will disable this code.
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Kernel 5.10 support for ipq806x was added at the same time that these
patches were developed for kernel 5.4. This carries the patches forward
to kernel 5.10.
fa731838c5 ipq806x: dwmac: clear forced speed during probe
75ca641f1b ipq806x: Add "snps,dwmac" to all gmac compatible=
d62825dd77 ipq806x: dwmac: set forced speed when using fixed-link
Signed-off-by: Mark Mentovai <mark@moxienet.com>
Run-tested: ipq806x/ubnt,unifi-ac-hd
Cc: Ansuel Smith <ansuelsmth@gmail.com>
d53be2a2e9 migrated 0069-arm-boot-add-dts-files.patch from patches-5.4
to patches-5.10, but a subsequent patch in that set, 1e25423be8,
erroneously removed several devices:
ipq8062/nec,wg2600hp3 from 3bb1618573
ipq8064/asrock,g10 from 98b86296e6
ipq8064/ubnt,unifi-ac-hd from 4e46beb313
Signed-off-by: Mark Mentovai <mark@moxienet.com>
Run-tested: ipq806x/ubnt,unifi-ac-hd
Cc: Ansuel Smith <ansuelsmth@gmail.com>
Add support for pstore/ramoops now that DRAM content is preserved
over reboot on MT7622. On each boot, check pstore and boot to recovery
image in case there are records stored in it.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Most notably this enabled use of pstore/ramoops on MT7622 as DRAM
content is now preserved over reboot.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The out-of-tree qcom-smem patches traditionally displayed mtd partition names
in upper case, starting with the new mainline qcom-smem support in kernel v5.10,
it switches to normalizing the partition names to lower case.
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
The out-of-tree qcom-smem patches traditionally displayed mtd partition names
in upper case, starting with the new mainline qcom-smem support in kernel v5.10,
it switches to normalizing the partition names to lower case.
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
The out-of-tree qcom-smem patches traditionally displayed mtd partition names
in upper case, starting with the new mainline qcom-smem support in kernel v5.10,
it switches to normalizing the partition names to lower case.
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
