This commit adds support for Netgear Orbi Pro SXR80 and SXS80 (collectively known as SXK80)
Specifications:
---------------
* CPU: Qualcomm IPQ8074A Quad core Cortex-A53
* RAM: 1024MB
* Storage: SPI-NAND 512 MiB (Winbond W29N04GZ)
* Ethernet: 4x 1G RJ45 ports (QCA8075) 1x 2.5G RJ45 LAN/WAN (QCA8081)
* WLAN:
- 2.4 GHz: Qualcomm QCN5024 4x4
- 2x 5 GHz: Qualcomm QCN5054 4x4 (second radio high channels only)
* LEDs:
- Power: (Green and red)
- Front: (Blue, green, red and white)
* Buttons:
- 1x Soft reset
- 1x Sync/WPS
* Power: 12V DC Jack
Installation instructions (Telnet):
-----------------------------------
*Note, this guide assumes SXR80, for SXS80 change the firmware file name as appropriate
1. Put firmware file openwrt-qualcommax-ipq807x-netgear_sxr80-initramfs-uImage.itb in root of TFTP server available at 192.168.1.10.
2. Enable telnet by going to http://[ip of device]/debug.htm and clicking on the tickbox 'Enable telnet'
3. Telnet into the device and login using the same username and password as the web interface:
4. Run the following command:
`fw_setenv bootcmd 'env default -a; saveenv; reset'`
5. Reboot the router, once the web interface is available again re-enable telnet via http://[ip of device]/debug.htm and telnet into the device.
6. Run the following command:
`fw_printenv`
It should look similar to the below:
```
baudrate=115200
bootargs=console=ttyMSM0,115200n8
bootcmd=mii write 0x0 0x0 0x800; sleep 1; nmrp; bootdni; boot_DNI_secureboot
bootdelay=2
ipaddr=192.168.1.1
netmask=255.255.255.0
serverip=192.168.1.10
soc_version_major=2
soc_version_minor=0
```
**If you see the message:**
`Warning: Bad CRC, using default environment`
**DO NOT CONTINUE, YOU WILL BRICK YOUR DEVICE**
7. Run the following command:
`fw_setenv originalboot 'mii write 0x0 0x0 0x800; sleep 1; nmrp; bootdni; boot_DNI_secureboot'`
(This should match what's in the bootcmd variable displayed in step 6)
8. Run the following commands:
```
fw_setenv wrttftp 'mii write 0x0 0x0 0x800; sleep 1; nmrp; if tftpboot openwrt-qualcommax-ipq807x-netgear_sxr80-initramfs-uImage.itb; then bootm; fi; bootdni; boot_DNI_secureboot'
fw_setenv wrtboot 'mii write 0x0 0x0 0x800; sleep 1; nmrp; nand read 0x40000000 0x1980000 0x06d00000; bootm 0x40000000'
fw_setenv bootcmd 'run wrttftp'
```
9. Ensure SXR/S device is attached via ethernet (LAN port) to the same ethernet segment as the TFTP server.
10. Reboot the device, it should reboot into OpenWrt and be available on 192.168.1.1
11. Once OpenWrt has booted, update the bootcmd using the following command:
`fw_setenv bootcmd 'run wrtboot'`
12. Flash the sysupgrade image
13. It should boot into OpenWrt
References to SXK80 GPL source:
https://www.downloads.netgear.com/files/GPL/SXK80-V3.2.0.108_gpl_src.tar.bz2.zip
Signed-off-by: Flole Systems <flole@flole.de>
Signed-off-by: Andrew Smith <gul.code@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/14939
Signed-off-by: Robert Marko <robimarko@gmail.com>
Hardware specification:
========
SoC: Qualcomm IPQ8072A
Flash: 512MB (Fidelix FMND4G08S3J-ID)
RAM: 1GB (2x Kingston DDR3L D2516ECMDXGJD)
Ethernet: 1x 10/100/1000/2500/5000Mbps (Marvell AQR114C)
Ethernet: 4x 10/100/1000Mbps (Qualcomm QCA8075)
WiFi1: 6GHz ax 4x4 (Qualcomm QCN9024 + Skyworks SKY85784-11) - channels 33-229
WiFi2: 5GHz ax 4x4 (Qualcomm QCN5054 + Skyworks SKY85755-11) - channels 36-177
WiFi3: 2.4GHz ax 4x4 (Qualcomm QCN5024 + Skyworks SKY8340-11)
IoT: Bluetooth 5, Zigbee and Thread (NXP K32W041)
LED: 1x RGB status (NXP PCA9633)
USB: 1x USB 3.0
Button: WPS, Reset
Flash instructions:
========
1. Manually upgrade firmware using openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin image.
More details can be found here: https://www.linksys.com/support-article?articleNum=47547
After first boot check actual partition:
- fw_printenv -n boot_part
and install firmware on second partition using command in case of 2:
- mtd -r -e kernel -n write openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin kernel
and in case of 1:
- mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin alt_kernel
2. Installation using serial connection from OEM firmware (default login: root, password: admin):
- fw_printenv -n boot_part
In case of 2:
- flash_erase /dev/mtd21 0 0
- nandwrite -p /dev/mtd21 openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin
or in case of 1:
- flash_erase /dev/mtd23 0 0
- nandwrite -p /dev/mtd23 openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin
After first boot install firmware on second partition:
- mtd -r -e kernel -n write openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin kernel
or:
- mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin alt_kernel
3. Installation from initramfs image using USB drive:
Put the initramfs image on the USB drive:
- dd bs=1M if=openwrt-qualcommax-ipq807x-linksys_mx8500-initramfs-uImage.itb of=/dev/sda
Stop u-boot and run:
- usb start && usbboot $loadaddr 0 && bootm $loadaddr
Write firmware to the flash from initramfs:
- mtd -e kernel -n write openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin kernel
and:
- mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin alt_kernel
4. Back to the OEM firmware:
- mtd -e kernel -n write FW_MX8500_1.0.11.208937_prod.img kernel
and:
- mtd -r -e alt_kernel -n write FW_MX8500_1.0.11.208937_prod.img alt_kernel
5. USB recovery:
Put the initramfs image on the USB:
- dd bs=1M if=openwrt-qualcommax-ipq807x-linksys_mx8500-initramfs-uImage.itb of=/dev/sda
Set u-boot env:
- fw_setenv bootusb 'usb start && usbboot $loadaddr 0 && bootm $loadaddr'
- fw_setenv bootcmd 'run bootusb; if test $auto_recovery = no; then bootipq; elif test $boot_part = 1; then run bootpart1; else run bootpart2; fi'
AQR firmware:
========
1. Firmware loading:
To properly load the firmware and initialize AQR PHY, we must use the u-boot aq_load_fw function.
To do this, you need to modify u-boot env:
With USB recovery:
- fw_setenv bootcmd 'aq_load_fw; run bootusb; if test $auto_recovery = no; then bootipq; elif test $boot_part = 1; then run bootpart1; else run bootpart2; fi'
and without:
- fw_setenv bootcmd 'aq_load_fw; if test $auto_recovery = no; then bootipq; elif test $boot_part = 1; then run bootpart1; else run bootpart2; fi'
2. Firmware updating:
Newer firmware (AQR-G4_v5.6.5-AQR_WNC_SAQA-L2_GT_ID45287_VER24005.cld) is available in the latest OEM firmware.
To load this firmware via u-boot, we need to add the MBN header and update 0:ethphyfw partition.
For MBN header we can use script from this repository: https://github.com/testuser7/aqr_mbn_tool
- python aqr_mbn_tool.py AQR-G4_v5.6.5-AQR_WNC_SAQA-L2_GT_ID45287_VER24005.cld
To update partition we need to install kmod-mtd-rw package first:
- insmod mtd-rw.ko i_want_a_brick=1
- mtd -e /dev/mtd26 -n write aqr_fw.mbn /dev/mtd26
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/14883
Signed-off-by: Robert Marko <robimarko@gmail.com>
Define common Linksys MX device for MX4200v1/v2 and MX5300.
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/14883
Signed-off-by: Robert Marko <robimarko@gmail.com>
Spectrum SAX1V1K is a AX WIFI router with 3 1G and 1 2.5G ports.
The router is provided to Spectrum customers.
It is OEM of Askey RT5010W
https://forum.openwrt.org/t/spectrum-sax1v1k-askey-rt5010w-openwrt-support/149923
It continues the original work by @MeisterLone to get this device supported.
Specifications:
```
• CPU: Qualcomm IPQ8072A Quad core Cortex-A53 2.2GHz
• RAM: 2048MB of DDR3
• Storage: 1024MB eMMC
• Ethernet: 3x 1G RJ45 ports (QCA8075) + 1 2.5G Port (QCA8081)
• WLAN:
• 2.4GHz: Qualcomm QCN5024 4x4 802.11b/g/n/ax 1174 Mbps PHY rate
• 5GHz: Qualcomm QCN5054 4x4 802.11a/b/g/n/ac/ax 2402 PHY rate
• LED: 1 gpio-controlled dual color led (blue/red)
• Buttons: 1x reset
• Power: 12V DC jack
```
Notes:
```
• This commit adds only single partition support, that means
sysupgrade is upgrading the current rootfs partition.
• Installation can be done by serial connection only.
• A poulated serial header is onboard
https://forum.openwrt.org/t/spectrum-sax1v1k-askey-rt5010w-openwrt-support/149923/6
• RX/TX is working, u-boot bootwait is active, secure boot is enabled.
```
Installation Instructions:
**Most part of the installation is performed from an initramfs image.**
Boot initramfs : Using serial connection
1. Boot up the device and wait till it displays "VERIFY_IB: Success. verify IB ok"
2. Once that message appears,
login with username 'root'
password serial number of your router in uppercase.
3. Use vi to paste the 'open.sh' script from @MeisterLone github on your device
https://github.com/MeisterLone/Askey-RT5010W-D187-REV6/blob/master/Patch/open.sh
4. chmod 755 open.sh
5. ./open.sh
6. Set your ip to 192.168.0.1
7. Run a TFTP server and host the initramfs image on the TFTP server and name it "recovery.img"
8. Reboot device. On boot it will try TFTP.
Install OpenWrt from initramfs image:
1. Use SCP (or other way) to transfer OpenWrt factory image
2. Connect to device using SSH (on a LAN port)
3. Flash firmware: sysupgrade
# sysupgrade -n -v /tmp/openwrt_sysupgrade.bin
4. Set U-boot env variable: bootcmd
# fw_setenv bootcmd "run fix_uboot; run setup_and_boot"
5. Reboot the device
# reboot
6. Once device is booted, residue of previous firmware will prevent openwrt to work properly.
Factory Reset is MUST required
# Once serial console is displaying to login, hold reset button for 10 sec
7. Now everything should be operational.
Note: this PR adds only single partition support, that means sysupgrade is
upgrading the current rootfs partition
Signed-off-by: Connor Yoon <j_connor@taliaent.com>
Netgear WAX214 is a 802.11 ax dual-band AP
with PoE. (similar to Engenius EWS357APV3)
Specifications:
• CPU: Qualcomm IPQ6010 Quad core Cortex-A53
• RAM: 512MB of DDR3
• Storage: 128MB NAND (Macronix MX30UF1G18AC)
• Ethernet: 1x 1G RJ45 port (QCA8072) PoE
• WIFI:
2.4GHz: Qualcomm QCN5022 2x2 802.11b/g/n/ax 574 Mbps PHY rate
5GHz: Qualcomm QCN5052 2x2 802.11a/b/g/n/ac/ax 1201 PHY rate
• LEDs:
4 x GPIO-controlled LEDs
- 1 Power LED (orange)
- 1 LAN LED (blue)
- 1 WIFI 5g LED (blue)
- 1 WIFI 2g LED (blue)
black_small_square Buttons: 1x soft reset
black_small_square Power: 12V DC jack or PoE (802.3af )
An populated serial header is onboard, format is
1.25mm 4p (DF13A-4P-1.25H)
RX/TX is working, bootwait is active, secure boot is not
enabled.
The root password of the stock firmware is unknown,
but failsafe mode can be entered to reset the password.
Installation Instructions:
- obtain serial access
- stop auto boot (press "4", Entr boot command line
interface)
- setenv active_fw 0 (to boot from the primary rootfs,
or set to 1 to boot from the secondary rootfs
partition)
- saveenv
- tftpboot the initramfs image
- bootm
- copy
openwrt-qualcommax-ipq60xx-netgear_wax214-squashfs-factory.ubi
to the device
- write the image to the NAND:
- cat /proc/mtd and look for rootfs partition (should
be mtd11,
or mtd12 if you choose active_fw 1)
- ubiformat /dev/mtd11 -f -y
openwrt-qualcommax-ipq60xx-netgear_wax214-squashfs-factory.ubi
- reboot
Note: the firmware is senao-based. But I was unable to build
a valid senao-header into the image.
Maybe they changed the header format and senaoFW isn't
working any more.
Signed-off-by: Dirk Buchwalder <buchwalder@posteo.de>
These recipes are generic and will be used for other subtargets, so lets
move them to the target Makefile so they can reused.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Introduce support for the Qualcomm IPQ60xx SoC. WiFi support still has
to be handled and correctly fix hence this is currently marked as
source-only to have a solid base to progress on correct support of this
and hope Upstream QUIC publish newers ath11k drivers for this SoC.
Co-developed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Mantas Pucka <mantas@8devices.com>
[ improve commit description, add SoB for Robert, make it source-only ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Enable LED driver LP5562 on HAZE device tree and include its kernel
module package on default package for HAZE.
Signed-off-by: CheWei Chien <chewei.chien@wnc.com.tw>
Linksys MX4200 is a 802.11ax Tri-band router/AP.
Specifications:
* CPU: Qualcomm IPQ8174 Quad core Cortex-A53 1.4GHz
* RAM: 512MB of DDR3
* Storage: 512Mb NAND
* Ethernet: 4x1G RJ45 ports (QCA8075)
* WLAN:
* 2.4GHz: Qualcomm QCN5024 2x2 802.11b/g/n/ax 574 Mbps PHY rate
* 5GHz: Qualcomm QCN5054 2x2@80MHz or 2x2@160MHz 802.11a/b/g/n/ac/ax 2402 PHY rate
* 5GHz: Qualcomm QCN5054 4x4@80MHz or 2x2@160MHz 802.11a/b/g/n/ac/ax 2402 PHY rate
* LED-s:
* RGB system led
* Buttons: 1x Soft reset 1x WPS
* Power: 12V DC Jack
Installation instructions:
Open Linksys Web UI - http://192.168.1.1/ca or http://10.65.1.1/ca depending on your setup.
Login with your admin password. The default password can be found on a sticker under the device.
To enter into the support mode, click on the “CA” link and the bottom of the page.
Open the “Connectivity” menu and upload the squash-factory image with the “Choose file” button.
Click start. Ignore all the prompts and warnings by click “yes” in all the popups.
The Wifi radios are turned off by default. To configure the router, you will need to connect your computer to the LAN port of the device.
Then you would need to write openwrt to the other partition for it to work
- First Check booted partition
fw_printenv -n boot_part
- Then install Openwrt to the other partition if booted in slot 1:
mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq807x-linksys_mx4200v(X)-squashfs-factory.bin alt_kernel
- If in slot 2:
mtd -r -e kernel -n write openwrt-qualcommax-ipq807x-linksys_mx4200v(X)-squashfs-factory.bin kernel
Replace (X) with your model version either 1 or 2
Signed-off-by: Mohammad Sayful Islam <sayf.mohammad01@gmail.com>
Reviewed-by: Robert Marko <robimarko@gmail.com>
Hardware specifications:
SoC: Qualcomm IPQ8071A
RAM: 512MB of DDR3
Flash1: Eon EN25S64 8MB
Flash2: MX30UF2G18AC 256MB
Ethernet: 2x 2.5G RJ45 port
Phone: 1x RJ11 port (SPI)
USB: 1x Type-C 2.0 port
WiFi1: QCN5024 2.4GHz
WiFi2: QCN5054 5GHz
Button: Reset, WPS
Flash instructions:
1. Connect the router via serial port (115200 8N1 1.8V)
2. Download the initramfs image, rename it to initramfs.bin,
and host it with the tftp server.
3. Interrupt U-Boot and run these commands:
tftpboot initramfs.bin
bootm
4. After openwrt boots up, use scp or luci web
to upload sysupgrade.bin to upgrade.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Reviewed-by: Robert Marko <robimarko@gmail.com>
Hardware specification:
SoC: Qualcomm IPQ8072A
Flash: Toshiba NAND 1GiB
RAM: 1 GiB of DDR3 466 MHz
Ethernet: 4x 1Gbps + 1x 2.5Gbps
WiFi1: QCN5024 2.4GHz ax 4x4
WiFi2: QCN5054 5GHz ax 4x4
Button: WiFi, WPS, Reset
Modem: RG500Q-EA
USB: 1 x USB 3.0
Power: DC 12V 4A
Flash instructions:
1. Download the initramfs image, rename it to
initramfs.bin, and host it with tftp server.
2. Interrupt U-Boot and run these commands:
tftpboot initramfs.bin
bootm
3. After openwrt boots up, use scp or luci web
to upload sysupgrade.bin to upgrade.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Reviewed-by: Robert Marko <robimarko@gmail.com>
Replace blanks with tabs, also sort base-files alphabetically.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Reviewed-by: Robert Marko <robimarko@gmail.com>
This makes it possible to build the ipq807x netgear-wax218 without initramfs - which is required for downstream projects (gluon)
Signed-off-by: Florian Maurer <f.maurer@outlook.de>
```
Specifications:
* CPU: Qualcomm IPQ8074A, SoC Version: 2.0, Quad core 1651 MHz
* RAM: 1 GiB of DDR3 466 MHz
* Flash: NAND 512 MiB (Winbond W29N04GZ)
* 6 RGB LEDs: Power, LAN1, LAN2, 2.4GHz, 5GHz H and 5GHz L
* UART: One 4-pin populated header next to the heatsink and a chip.
GND RXD TXD, beginning from the external antennas. 115200n8.
Lan:
* One 100/1000/2.5GBASE-T Gigabit Ethernet 802.3bt/at
* One 100/1000 Gigabit Ethernet
Wlan:
* 4x4 in 2.4GHz : 802.11b/g/n/ax
* 4x4 in 5.0GHz L: 802.11a/n/ac/ax
* 4x4 in 5.0GHz H: 802.11a/n/ac/ax
* OFDM and OFDMA
* Bidir and MU-MIMO
* Internal antenna 2.86/4.41/4.98 dBi (2.4GHz/5GHz L/5GHz H)
Power:
* 802.3bt/at 30.1W
* DC 12V/3.5A
Mounting: Wall and ceiling
```
```
1. Download the OpenWrt initramfs image. Copy the image to a TFTP server
2. Connect to the console on the AP, and connect the LAN port to your LAN
3. Stop auto boot to get to U-boot shell, interrupt the autoboot process by pressing '0' when prompted
4. Set active_fw in env
4. Set active_fw in env
# setenv active_fw 1
5. Transfer the initramfs image with TFTP
# setenv serverip 192.168.1.10 (IP of TFTP server host)
# setenv ipaddr 192.168.1.1 (IP used by the router for getting the image, must be in the same subnet as the TFTP host)
# tftpboot openwrt-qualcommax-ipq807x-netgear_wax630-initramfs-uImage.itb
6. Reboot and load the image
# bootm
7. SCP factory image to the AP
# scp openwrt-qualcommax-ipq807x-netgear_wax630-squashfs-factory.ubi root@192.168.1.1:/tmp/
8. Connect to device using SSH (use the LAN port)
9. Flash squashfs-factory.ubi from within the initramfs instance of OpenWRT
Before you flash, please check your mtd partitions where mtdX is the right mtd rootfs partition.
# cat /proc/mtd (To check MTD partitions)
# ubiformat /dev/mtd18 -y -f /tmp/openwrt-qualcommax-ipq807x-netgear_wax630-squashfs-factory.ubi
10. Set active_fw to 0
# /usr/sbin/fw_setenv active_fw 0
11. Reboot the AP and your done
# reboot
```
Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Kristian Skramstad <kristian+github@83.no>
As requested by the maintainers, the order for the WAX family
should be alphabetically. WAX620 is now after WAX218.
Files changed:
+ipq807x.mk
+01_leds
No changes to the content.
Signed-off-by: Kristian Skramstad <kristian+github@83.no>
```
Specifications:
* CPU: Qualcomm IPQ8072A, SoC Version: 2.0, Quad core Cortex-A53 1.6896 GHz
* RAM: 1 GiB of DDR4 600 MHz
* Flash: NAND 2x256 MiB (Macronix MX30UF2G18AC)
* 4 RGB LEDs: Power, LAN, 2.4GHz and 5GHz
* UART: Two 4-pin unpopulated headers under the LEDs.
Use the header closest to LED 4 and 5.
They are marked with a white stroke.
TX RX GND, beginning from "4". 115200n8.
Lan:
* One 100/1000/2.5GBASE-T Gigabit Ethernet (QCA8081)
Wlan:
* 4x4 in 2.4GHz: 802.11b/g/n/ax
* 4x4 in 5.0GHz: 802.11a/n/ac/ax
* OFDM and OFDMA
* Bidir and MU-MIMO
* Internal antenna 3.1/4.3 dBi (2.4GHz/5GHz)
Power:
* PoE+ 802.3at/af 25.5W
* DC 12V 2.5A
```
```
Note: The OpenWrt image is setup with DHCP and not a static IP.
1. Download the OpenWrt initramfs image. Copy the image to a TFTP server
2. Connect to console on the AP, and connect the LAN port to your LAN
3. Stop auto boot to get to U-boot shell, interrupt the autoboot process by pressing '0' when prompted
4. Set active_fw in env
# setenv active_fw 1
5. Transfer the initramfs image with TFTP
# setenv serverip 192.168.1.10 (IP of TFTP server host)
# setenv ipaddr 192.168.1.1 (IP used by the router for getting the image, must be in the same subnet as the TFTP host)
# tftpboot openwrt-qualcommax-ipq807x-netgear_wax620-initramfs-uImage.itb
6. Reboot and load the image
# bootm
7. SCP factory image to the AP
# scp openwrt-qualcommax-ipq807x-netgear_wax620-squashfs-factory.ubi root@192.168.1.1:/tmp/
8. Connect to device using SSH (use the LAN port)
9. Flash squashfs-factory.ubi from within the initramfs instance of OpenWRT
Before you flash, please check your mtd partitions where mtdX is the right mtd rootfs partition.
# cat /proc/mtd (To check MTD partitions)
# ubiformat /dev/mtd19 -y -f /tmp/openwrt-qualcommax-ipq807x-netgear_wax620-squashfs-factory.ubi
10. Set active_fw to 0
# /usr/sbin/fw_setenv active_fw 0
11. Reboot the AP and your done
# reboot
```
Signed-off-by: Kristian Skramstad <kristian+github@83.no>
Netgear Nighthawk RAX120v2 AX WIFI router with 5 1G and 1 5G ports.
The majority of the code is based on @jewwest's PR #11830.
Specifications:
* CPU: Qualcomm IPQ8074 Quad core Cortex-A53 2.2GHz
* RAM: 1024MB of DDR3 (Nanya NT5CC256M16EP-EK × 2)
* Flash: SPI-NAND 512 MiB (Winbond W29N04GZBIBA)
* Ethernet: 4x 10/100/1000 Mbps LAN,
1x 10/100/1000 Mbps WAN (Qualcomm QCA8075),
1x 10/100/1000/2500/5000 Mbps LAN/WAN (Aquantia AQR111B0 PHY)
* Wi-Fi:
* 2.4 GHz: Qualcomm QCN5024 4x4
* 2x 5 GHz: Qualcomm QCN5054 4x4
* USB: 2x USB 3.0
* LEDs: Power, 2.4GHz & 5GHz Radio, WPS, WAN, USB1 & USB2, 5G LAN
* Keys: LEDs On/Off, Power, Reset, RFKILL, WPS
* UART: Marked J9003 VCC TX RX GND, beginning from "1". 3.3v, 115200n8
* Power: 19 VDC, 3.1 A
Installation:
* Flashing OpenWrt is done in two steps:
a) Flash *-squashfs-web-ui-factory.img from stock UI (thanks to @wangyu-).
This writes an initramfs based OpenWrt image onto the RAX120v2
b) From OpenWrt flash the *-squashfs-sysupgrade.bin using LuCI or the commandline
* U-Boot allows booting an initramfs image via TFTP:
- Set ip of your PC to 192.168.1.100
- At the serial console interrupt boot at "Hit any key to stop autoboot:"
- In u-boot run `tftpsrv`
- On your PC send the OpenWrt initramfs image:
tftp 192.168.1.1 -m binary -c put openwrt-ipq807x-generic-netgear_rax120v2-initramfs-uImage.itb
Make 5G Aquantia phy work:
For the 5G port labeled 'lan5' to work a firmware is needed. This can be loaded in
u-boot by writing the firmware to the correct mtd partition.
The firmware file found in the Netgear stock firmware under /lib/firmware/ named
'AQR-G3_v4.3.C-AQR_DNI_DR-EQ35AX8-R-prov1_ID23888_VER1311.cld' is needed and has to
be converted to a MBN file.
The `mkheader.py` script used here can be found in the Netgear V1.2.8.40 GPL source,
under 'git_home/u-boot.git/tools/mkheader.py'
Convert the CLD file to MBN using:
$ python2 mkheader.py 0x44000000 0x13 <*.cld file> aqr_4.3.C.mbn
This MBN file can then be flashed to the MTD partition to be used by u-boot.
The necessary files can also be found in
https://github.com/boretom/openwrt-fork/tree/rax120v2/aquantia-firmware
* Write MBN file to MTD partition to be loaded automatically by u-boot:
U-boot automatically tries to load the firmware from nand at address 0x7e00000 which
corresponds to `/dev/mtd25` in OpenWrt.
- find ETHPHYFW partition while running OpenWrt (expected: /dev/mtd25)
$ fgrep -i 'ethphyfw' /proc/mtd
mtd25: 00080000 00020000 "ethphyfw
- copy mbn file to /tmp/ folder of the router
$ scp aqr-v4.3.C.mbn 192.168.1.1:/tmp/
- write mbn file to ethphyfw partition
$ mtd write /tmp/aqr_v4.3.C.mbn /dev/mtd25
Revert to stock firmware:
* Flash the stock firmware to the bootloader using TFTP/NMRP.
References to RAX120v2 GPL source:
https://www.downloads.netgear.com/files/GPL/RAX120-V1.2.8.40_gpl_src.zip
Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Thomas Kupper <thomas.kupper@gmail.com>
While flashing sysupgrade image from U-Boot, then the rootfs_data
overlay filesystem formatting is left for the fstools during firstboot,
but that wont work as mkfs.f2fs is missing in the sysupgrade image:
mount_root: overlay filesystem in /dev/loop0 has not been formatted yet
mount_root: no usable overlay filesystem found, using tmpfs overlay
sh: mkfs.f2fs: not found
Filesystem Size Used Available Use% Mounted on
/dev/loop0 139.6M 46.9M 92.6M 34% /overlay
Number Start (sector) End (sector) Size Code Name
20 98850 406349 150.1 MiB FFFF rootfs
So lets fix it by adding f2fs support to the sysupgrade image.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Currently, Compex WPQ873 images are not including the ath11k BDF-s at all
and this means that there is no WLAN support, so lets include the BDF as
its already packaged.
Fixes: 07c45c0859 ("ipq807x: add support for Compex WPQ873")
Signed-off-by: Robert Marko <robimarko@gmail.com>
Now that qualcommax exists as a target and dependencies have been updated
let move ipq807x support to subtarget of qualcommax.
This is mostly copy/paste with the exception of having to update SSDK and
NSS-DP to use CONFIG_TARGET_SUBTARGET.
This is a preparation for later addition of IPQ60xx and IPQ50xx support.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Currently, ipq807x only covers Qualcomm IPQ807x SoC-s.
However, Qualcomm also has IPQ60xx and IPQ50xx SoC-s under the AX WiSoC-s
and they share a lot of stuff with IPQ807x, especially IPQ60xx so to avoid
duplicating kernel patches and everything lets make a common target with
per SoC subtargets.
Start doing that by renaming ipq807x to qualcommax so that dependencies
on ipq807x target can be updated.
Signed-off-by: Robert Marko <robimarko@gmail.com>
