ALFA Network N2Q is an outdoor N300 AP/CPE based on Qualcomm/Atheros
QCA9531 v2. This model is a successor of the old N2 which was based
on Atheros AR7240. FCC ID: 2AB8795311.
Specifications:
- Qualcomm/Atheros QCA9531 v2
- 650/400/200 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of flash (SPI NOR)
- 2T2R 2.4 GHz Wi-Fi with ext. PA (Skyworks SE2623L) and LNA
- 2x 10/100 Mbps Ethernet with passive PoE input in one port (24 V)
- PoE pass through in second port (controlled by GPIO)
- support for optional 802.3af/at PoE module
- 1x mini PCIe slot (PCIe bus, extra 4.2 V for high power cards)
- 2x IPEX/U.FL connectors on PCB
- 1x USB 2.0 mini Type-B (power controlled by GPIO)
- 8x LED (7 of them are driven by GPIO)
- 1x button (reset)
- external h/w watchdog (EM6324QYSP5B, enabled by default)
- UART (4-pin, 2.54 mm pitch) header on PCB
- LEDs (2x 5-pin, 2.54 mm pitch) header on PCB
Flash instruction:
You can use sysupgrade image directly in vendor firmware which is based
on LEDE/OpenWrt. Alternatively, you can use web recovery mode in U-Boot:
1. Configure PC with static IP 192.168.1.2/24.
2. Connect PC with one of RJ45 ports, press the reset button, power up
device, wait for first blink of all LEDs (indicates network setup),
then keep button for 3 following blinks and release it.
3. Open 192.168.1.1 address in your browser and upload sysupgrade image.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
ALFA Network R36A is a successor of the previous model, the R36 (Ralink
RT3050F based). New version is based on Qualcomm/Atheros QCA9531 v2, FCC
ID: 2AB879531.
Support for this device was first introduced in af8f0629df (ar71xx
target). When updating from previous release (and/or ar71xx target),
user should only adjust the WAN LED trigger type (netdev in ar71xx,
switch port in ath79).
Specifications:
- Qualcomm/Atheros QCA9531 v2
- 650/400/200 MHz (CPU/DDR/AHB)
- 128 MB (R36AH/-U2) or 64 MB (R36A) of RAM (DDR2)
- 16 MB of flash (SPI NOR)
- 2x 10/100 Mbps Ethernet
- Passive PoE input support (12~36 V) in RJ45 near DC jack
- 2T2R 2.4 GHz Wi-Fi with Qorvo RFFM8228P FEM
- 2x IPEX/U.FL connectors on PCB
- 1x USB 2.0 Type-A
- 1x USB 2.0 mini Type-B in R36AH-U2 version
- USB power is controlled by GPIO
- 6/7x LED (5/6 of them are driven by GPIO)
- 2x button (reset, wifi/wps)
- external h/w watchdog (EM6324QYSP5B, enabled by default)
- DC jack with lock, for main power input (12 V)
- UART (4-pin, 2.54 mm pitch) header on PCB
Optional/additional features in R36A series (R36A was the first model):
- for R36AH: USB 2.0 hub*
- for R36AH-U2: USB 2.0 hub*, 1x USB 2.0 mini Type-B, one more LED
*) there are at least three different USB 2.0 hub in R36AH/-U2 variants:
- Terminus-Tech FE 1.1
- Genesys Logic GL852G
- Genesys Logic GL850G (used in latests revision)
Flash instruction:
You can use sysupgrade image directly in vendor firmware which is based
on LEDE/OpenWrt. Alternatively, you can use web recovery mode in U-Boot:
1. Configure PC with static IP 192.168.1.2/24.
2. Connect PC with one of RJ45 ports, press the reset button, power up
device, wait for first blink of all LEDs (indicates network setup),
then keep button for 3 following blinks and release it.
3. Open 192.168.1.1 address in your browser and upload sysupgrade image.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Samsung WAM250 is a dual-band (selectable, not simultaneous) wireless
hub, dedicated for Samsung Shape Wireless Audio System. The device is
based on Atheros AR9344 (FCC ID: A3LWAM250). Support for this device
was first introduced in e58e49bdbe (ar71xx target).
Specifications:
- Atheros AR9344
- 560/450/225 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 16 MB of flash (SPI NOR)
- 2x 10/100 Mbps Ethernet
- 2T2R 2.4/5 GHz Wi-Fi, with ext. PA (SE2598L, SE5003L) and LNA
- 1x USB 2.0
- 4x LED (all are driven by GPIO)
- 2x button (reset, wps/speaker add)
- DC jack for main power input (14 V)
- UART header on PCB (J4, RX: 3, TX: 5)
Flash instruction:
This device uses dual-image (switched between upgrades) with a common
jffs2 config partition. Fortunately, there is a way to disable this mode
so that more flash space can be used by OpenWrt image.
You can easily access this device over telnet, using root/root
credentials (the same also work for serial console access).
1. Make sure that your device uses second (bootpart=2) image using
command: "fw_printenv bootpart".
2. If your device uses first image (bootpart=1), perform upgrade to the
latest vendor firmware (after the update, device should boot from
second partition) using web gui (default login: admin/1234567890).
3. Rename "sysupgrade" image to "firmware.bin", download it (you can use
wget, tftp or ftpget) to "/tmp" and issue below commands:
mtd_debug erase /dev/mtd3 0 $(wc -c /tmp/firmware.bin | awk -F' ' '{print $1}')
mtd_debug write /dev/mtd3 0 $(wc -c /tmp/firmware.bin)
fw_setenv bootpart
fw_setenv bootcmd "bootm 0x9f070000"
reboot
Revert to vendor firmware instruction:
1. Download vendor firmware to "/tmp" device and issue below commands:
fw_setenv bootpart 1
sysupgrade -n -F SS_BHUB_v2.2.05.bin
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Wallys DR531 is based on Qualcomm Atheros QCA9531 v2. Support for this
device was first introduced in e767980eb8 (ar71xx target).
Specifications:
- Qualcomm/Atheros QCA9531 v2
- 550/400/200 MHz (CPU/DDR/AHB)
- 2x 10/100 Mbps Ethernet
- 64 MB of RAM (DDR2)
- 8 MB of flash (SPI NOR)
- 2T2R 2.4 GHz Wi-Fi, with external PA (SE2576L), up to 30 dBm
- 2x MMCX connectors (optional IPEX/U.FL)
- mini PCIe connector (PCIe/USB buses and mini SIM slot)
- 7x LED, 1x button, 1x optional buzzer
- UART, JTAG and LED headers on PCB
Flash instruction (do it under U-Boot, using UART):
tftpb 0x80060000 openwrt-ath79-...-dr531-squashfs-sysupgrade.bin
erase 0x9f050000 +$filesize
cp.b $fileaddr 0x9f050000 $filesize
setenv bootcmd "bootm 0x9f050000"
saveenv && reset
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
The AP121FE is a slightly modified version of already supported AP121F
model (added to ar71xx in 0c6165d21a and to ath79 in 334bbc5198).
The differences in compare to AP121F:
- no micro SD card reader
- USB data lines are included in Type-A plug
- USB bus switched to device/peripheral mode (permanently, in bootstrap)
Other than that, specifications are the same:
- Atheros AR9331
- 400/400/200 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR1)
- 16 MB of flash (SPI NOR)
- 1x 10/100 Mbps Ethernet
- 1T1R 2.4 GHz Wi-Fi, up to 15 dBm
- 1x IPEX/U.FL connector, internal PCB antenna
- 3x LED, 1x button, 1x switch
- 4-pin UART header on PCB (2 mm pitch)
- USB 2.0 Type-A plug (power and data)
Flash instruction (under U-Boot web recovery mode):
1. Configure PC with static IP 192.168.1.2/24.
2. Connect PC with RJ45 port, press the reset button, power up device,
wait for first blink of all LEDs (indicates network setup), then keep
button for 3 following blinks and release it.
3. Open 192.168.1.1 address in your browser and upload sysupgrade image.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
The order of function and color in the labels in inverted for the
LAN LEDs. Fix it.
Fixes: 915966d861 ("ath79: Port PowerCloud Systems CAP324 support")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The LED color was missing in 01_leds.
Fixes: 745dee11ac ("ath79: add support for WD My Net Wi-Fi Range
Extender")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The "/dts-v1/;" identifier is supposed to be present once at the
top of a device tree file after the includes have been processed.
In ath79, we therefore requested to have in the DTS files so far,
and omit it in the DTSI files. However, essentially the syntax of
the parent ath79.dtsi file already determines the DTS version, so
putting it into the DTS files is just a useless repetition.
Consequently, this patch puts the dts-v1 statement into the parent
ath79.dtsi, which is (indirectly) included by all DTS files. All
other occurences are removed.
Since the dts-v1 statement needs to be before any other definitions,
this also moves the includes to make sure the ath79.dtsi or its
descendants are always included first.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
ath79.dtsi uses ATH79_CLK_MDIO, so the include
<dt-bindings/clock/ath79-clk.h>
needs to be moved there.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Move engenius_loader_okli image recipe in front of all Engenius
devices, so adding new device entries will not have them sorted
before the shared recipe.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
SPDX moved from GPL-2.0 to GPL-2.0-only and from GPL-2.0+ to
GPL-2.0-or-later. Reflect that in the SPDX license headers.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The legacy ar71xx target is removed and multiple targets use DTS now, so
there is no need to point that out for ATH79 specifically.
Signed-off-by: Paul Spooren <mail@aparcar.org>
The soft_config partition for these devices lays between 0xe000 and
0xf000 (as correctly detected by the RouterBoard platform driver),
before the bootloader2 partition which starts at 0x10000.
This commit correctly sorts the partitions, fixing the parsing error.
Fixes: FS#3314
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Reviewed-by: Thibaut VARÈNE <hacks@slashdirt.org>
This adds support for the Ubiquiti UniFi AP Pro to the ath79 target. The
device was previously supported on the now removed ar71xx target.
SoC Atheros AR9344
WiFi Atheros AR9344 & Atheros AR9280
ETH Atheros AR8327
RAM 128M DDR2
FLASH 16M SPI-NOR
Installation
------------
Follow the Ubiquiti TFTP recovery procedure for this device.
1. Hold down the reset button while connecting power for 10 seconds.
2. Transfer the factory image via TFTP to the AP (192.168.1.20)
3. Wait 2 minutes for the AP to write the firmware to flash. The device
will automatically reboot to OpenWrt.
Signed-off-by: David Bauer <mail@david-bauer.net>
Router and Movie "keys" are actually switches for both devices
according to the manual. This has been properly implemented in ar71xx,
but overlooked when porting to ath79.
Fixes: 480bf28273 ("ath79: add support for Buffalo WZR-HP-AG300H")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The hardware of this device seems to be identical to WZR-HP-AG300H.
It was already implemented as a clone in ar71xx.
Specification:
- 680 MHz CPU (Qualcomm Atheros AR7161)
- 128 MiB RAM
- 32 MiB Flash
- WiFi 5 GHz a/n
- WiFi 2.4 GHz b/g/n
- 5x 1000Base-T Ethernet
- 1x USB 2.0
Installation of OpenWRT from vendor firmware:
- Connect to the Web-interface at http://192.168.11.1
- Go to “Administration” → “Firmware Upgrade”
- Upload the OpenWrt factory image
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The Buffalo devices in ath79 share their image generation code,
so let's create a shared Device definition for them.
Since most of them use BUFFALO_HWVER := 3, this is moved as
default to the shared definition as well.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The tp-link safeloader devices typically contain a partition
"default-mac" which stores the MAC addresses. It is followed by other
partitions containing device info, like
{"default-mac", 0x610000, 0x00020},
{"pin", 0x610100, 0x00020},
{"product-info", 0x611100, 0x01000},
In DTS, we typically assign a 0x10000 sized partition for these,
which is mostly labelled "mac" or "info". In rarer cases, the
partitions have been enclosed in a larger "tplink" or "config"
partition.
However, when comparing different devices, the implementation appears
relatively arbitrary at the moment.
Thus, this PR aims at harmonizing these partitions by always using
the name "info" for the DTS partition containing "default-mac".
"info" is preferred over "mac" as we never just have "default-mac"
alone, but always some other device-info partitions as well.
While at it, this also establishes a similar partitioning for the
few devices where the "info" partitions are part of a bigger
unspecific "config" partition or similar.
Besides the harmonization itself, this also allows to merge a few
cases in 11-ath10k-caldata.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
TP-Link EAP225-Wall v2 is an AC1200 (802.11ac Wave-2) wall plate access
point. UART access and debricking require fine soldering.
The device was kindly provided for porting by Stijn Segers.
Device specifications:
* SoC: QCA9561 @ 775MHz
* RAM: 128MiB DDR2
* Flash: 16MiB SPI-NOR (GD25Q127CSIG)
* Wireless 2.4GHz (SoC): b/g/n, 2x2
* Wireless 5Ghz (QCA9886): a/n/ac, 2x2 MU-MIMO
* Ethernet (SoC): 4× 100Mbps
* Eth0 (back): 802.3af/at PoE in
* Eth1, Eth2 (bottom)
* Eth3 (bottom): PoE out (can be toggled by GPIO)
* One status LED
* Two buttons (both work as failsafe)
* LED button, implemented as KEY_BRIGHTNESS_TOGGLE
* Reset button
Flashing instructions, requires recent firmware (tested on 1.20.0):
* ssh into target device and run `cliclientd stopcs`
* Upgrade with factory image via web interface
Debricking:
* Serial port can be soldered on PCB J4 (1: TXD, 2: RXD, 3: GND, 4: VCC)
* Bridge unpopulated resistors R162 (TXD) and R165 (RXD)
Do NOT bridge R164
* Use 3.3V, 115200 baud, 8n1
* Interrupt bootloader by holding CTRL+B during boot
* tftp initramfs to flash via sysupgrade or LuCI web interface
MAC addresses:
MAC address (as on device label) is stored in device info partition at
an offset of 8 bytes. ath9k device has same address as ethernet, ath10k
uses address incremented by 1.
From OEM ifconfig:
br0 Link encap:Ethernet HWaddr 50:...:04
eth0 Link encap:Ethernet HWaddr 50:...:04
wifi0 Link encap:UNSPEC HWaddr 50-...-04-...
wifi1 Link encap:UNSPEC HWaddr 50-...-05-...
Signed-off-by: Sander Vanheule <sander@svanheule.net>
[fix IMAGE_SIZE]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
TP-Link EAP245 v3 is an AC1750 (802.11ac Wave-2) ceiling mount access
point. UART access (for debricking) requires non-trivial soldering.
Specifications:
* SoC: QCA9563 (CPU/DDR/AHB @ 775/650/258 MHz)
* RAM: 128MiB
* Flash: 16MiB SPI-NOR
* Wireless 2.4GHz (SoC): b/g/n 3x3
* Wireless 5GHz (QCA9982): a/n/ac 3x3 with MU-MIMO
* Ethernet (QCA8337N switch): 2× 1GbE, ETH1 (802.3at PoE) and ETH2
* Green and amber status LEDs
* Reset switch (GPIO, available for failsafe)
Flashing instructions:
All recent firmware versions (latest is 2.20.0), can disable firmware
signature verification and use a padded firmware file to flash OpenWrt:
* ssh into target device and run `cliclientd stopcs`
* upload factory image via web interface
The stopcs-method is supported from firmware version 2.3.0. Earlier
versions need to be upgraded to a newer stock version before flashing
OpenWrt.
Factory images for these devices are RSA signed by TP-Link. While the
signature verification can be disabled, the factory image still needs to
have a (fake) 1024 bit signature added to pass file checks.
Debricking instructions:
You can recover using u-boot via the serial port:
* Serial port is available from J3 (1:TX, 2:RX, 3:GND, 4:3.3V)
* Bridge R237 to connect RX, located next to J3
* Bridge R225 to connect TX, located inside can on back-side of board
* Serial port is 115200 baud, 8n1, interrupt u-boot by holding ctrl+B
* Upload initramfs with tftp and upgrade via OpenWrt
Device mac addresses:
Stock firmware has the same mac address for 2.4GHz wireless and
ethernet, 5GHz is incremented by one. The base mac address is stored in
the 'default-mac' partition (offset 0x90000) at an offset of 8 bytes.
ART blobs contain no mac addresses.
From OEM ifconfig:
ath0 Link encap:Ethernet HWaddr 74:..:E2
ath10 Link encap:Ethernet HWaddr 74:..:E3
br0 Link encap:Ethernet HWaddr 74:..:E2
eth0 Link encap:Ethernet HWaddr 74:..:E2
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
Enabled the ELF firmware partition splitter 4.19 and 5.4 in preparation
for the TP-Link EAP245v3 device support.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
This is the same as loader-kernel since the KERNEL_CMDLINE
parameter has been removed in [1] and not used at all anyway.
Remove it.
[1] f77db1a590 ("ath79: cleanup image build code")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Paul Spooren <mail@aparcar.org>
FCC ID: U2M-ENH200
Engenius ENH202 is an outdoor wireless access point with 2 10/100 ports,
built-in ethernet switch, internal antenna plates and proprietery PoE.
Specification:
- Qualcomm/Atheros AR7240 rev 2
- 40 MHz reference clock
- 8 MB FLASH ST25P64V6P (aka ST M25P64)
- 32 MB RAM
- UART at J3 (populated)
- 2x 10/100 Mbps Ethernet (built-in switch at gmac1)
- 2.4 GHz, 2x2, 29dBm (Atheros AR9280 rev 2)
- internal antenna plates (10 dbi, semi-directional)
- 5 LEDs, 1 button (LAN, WAN, RSSI) (Reset)
Known Issues:
- Sysupgrade from ar71xx no longer possible
- Power LED not controllable, or unknown gpio
MAC addresses:
eth0/eth1 *:11 art 0x0/0x6
wlan *:10 art 0x120c
The device label lists both addresses, WLAN MAC and ETH MAC,
in that order.
Since 0x0 and 0x6 have the same content, it cannot be
determined which is eth0 and eth1, so we chose 0x0 for both.
Installation:
2 ways to flash factory.bin from OEM:
- Connect ethernet directly to board (the non POE port)
this is LAN for all images
- if you get Failsafe Mode from failed flash:
only use it to flash Original firmware from Engenius
or risk kernel loop or halt which requires serial cable
Method 1: Firmware upgrade page:
OEM webpage at 192.168.1.1
username and password "admin"
In upper right select Reset
"Restore to factory default settings"
Wait for reboot and login again
Navigate to "Firmware Upgrade" page from left pane
Click Browse and select the factory.bin image
Upload and verify checksum
Click Continue to confirm and wait 3 minutes
Method 2: Serial to load Failsafe webpage:
After connecting to serial console and rebooting...
Interrupt boot with any key pressed rapidly
execute `run failsafe_boot` OR `bootm 0x9f670000`
wait a minute
connect to ethernet and navigate to
"192.168.1.1/index.htm"
Select the factory.bin image and upload
wait about 3 minutes
Return to OEM:
If you have a serial cable, see Serial Failsafe instructions
*DISCLAIMER*
The Failsafe image is unique to Engenius boards.
If the failsafe image is missing or damaged this will not work
DO NOT downgrade to ar71xx this way, can cause kernel loop or halt
The easiest way to return to the OEM software is the Failsafe image
If you dont have a serial cable, you can ssh into openwrt and run
`mtd -r erase fakeroot`
Wait 3 minutes
connect to ethernet and navigate to 192.168.1.1/index.htm
select OEM firmware image from Engenius and click upgrade
Format of OEM firmware image:
The OEM software of ENH202 is a heavily modified version
of Openwrt Kamikaze bleeding-edge. One of the many modifications
is to the sysupgrade program. Image verification is performed
simply by the successful ungzip and untar of the supplied file
and name check and header verification of the resulting contents.
To form a factory.bin that is accepted by OEM Openwrt build,
the kernel and rootfs must have specific names...
openwrt-senao-enh202-uImage-lzma.bin
openwrt-senao-enh202-root.squashfs
and begin with the respective headers (uImage, squashfs).
Then the files must be tarballed and gzipped.
The resulting binary is actually a tar.gz file in disguise.
This can be verified by using binwalk on the OEM firmware images,
ungzipping then untaring, and by swapping headers to see
what the OEM upgrade utility accepts and rejects.
OKLI kernel loader is required because the OEM firmware
expects the kernel to be no greater than 1024k
and the factory.bin upgrade procedure would otherwise
overwrite part of the kernel when writing rootfs.
Note on built-in switch:
ENH202 is originally configured to be an access point,
but with two ethernet ports, both WAN and LAN is possible.
the POE port is gmac0 which is preferred to be
the port for WAN because it gives link status
where swconfig does not.
Signed-off-by: Michael Pratt <mpratt51@gmail.com>
[assign label_mac in 02_network, use ucidef_set_interface_wan,
use common device definition, some reordering]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Engenius ENS202EXT v1 is an outdoor wireless access point with 2 10/100 ports,
with built-in ethernet switch, detachable antennas and proprietery PoE.
FCC ID: A8J-ENS202
Specification:
- Qualcomm/Atheros AR9341 v1
- 535/400/200/40 MHz (CPU/DDR/AHB/REF)
- 64 MB of RAM
- 16 MB of FLASH MX25L12835F(MI-10G)
- UART (J1) header on PCB (unpopulated)
- 2x 10/100 Mbps Ethernet (built-in switch Atheros AR8229)
- 2.4 GHz, up to 27dBm (Atheros AR9340)
- 2x external, detachable antennas
- 7x LED (5 programmable in ath79), 1x GPIO button (Reset)
Known Issues:
- Sysupgrade from ar71xx no longer possible
- Ethernet LEDs stay on solid when connected, not programmable
MAC addresses:
eth0/eth1 *:7b art 0x0/0x6
wlan *:7a art 0x1002
The device label lists both addresses, WLAN MAC and ETH MAC,
in that order.
Since 0x0 and 0x6 have the same content, it cannot be
determined which is eth0 and eth1, so we chose 0x0 for both.
Installation:
2 ways to flash factory.bin from OEM:
- Connect ethernet directly to board (the non POE port)
this is LAN for all images
- if you get Failsafe Mode from failed flash:
only use it to flash Original firmware from Engenius
or risk kernel loop which requires serial cable
Method 1: Firmware upgrade page:
OEM webpage at 192.168.1.1
username and password "admin"
In upper right select Reset
"Restore to factory default settings"
Wait for reboot and login again
Navigate to "Firmware Upgrade" page from left pane
Click Browse and select the factory.bin image
Upload and verify checksum
Click Continue to confirm and wait 3 minutes
Method 2: Serial to load Failsafe webpage:
After connecting to serial console and rebooting...
Interrupt boot with any key pressed rapidly
execute `run failsafe_boot` OR `bootm 0x9fdf0000`
wait a minute
connect to ethernet and navigate to
"192.168.1.1/index.htm"
Select the factory.bin image and upload
wait about 3 minutes
*If you are unable to get network/LuCI after flashing*
You must perform another factory reset:
After waiting 3 minutes or when Power LED stop blinking:
Hold Reset button for 15 seconds while powered on
or until Power LED blinks very fast
release and wait 2 minutes
Return to OEM:
If you have a serial cable, see Serial Failsafe instructions
*DISCLAIMER*
The Failsafe image is unique to this model.
The following directions are unique to this model.
DO NOT downgrade to ar71xx this way, can cause kernel loop
The easiest way to return to the OEM software is the Failsafe image
If you dont have a serial cable, you can ssh into openwrt and run
`mtd -r erase fakeroot`
Wait 3 minutes
connect to ethernet and navigate to 192.168.1.1/index.htm
select OEM firmware image from Engenius and click upgrade
TFTP Recovery:
For some reason, TFTP is not reliable on this board.
Takes many attempts, many timeouts before it fully transfers.
Starting with an initramfs.bin:
Connect to ethernet
set IP address and TFTP server to 192.168.1.101
set up infinite ping to 192.168.1.1
rename the initramfs.bin to "vmlinux-art-ramdisk" and host on TFTP server
disconnect power to the board
hold reset button while powering on board for 8 seconds
Wait a minute, power LED should blink eventually if successful
and a minute after that the pings should get replies
You have now loaded a temporary Openwrt with default settings temporarily.
You can use that image to sysupgrade another image to overwrite flash.
Format of OEM firmware image:
The OEM software of ENS202EXT is a heavily modified version
of Openwrt Kamikaze bleeding-edge. One of the many modifications
is to the sysupgrade program. Image verification is performed
simply by the successful ungzip and untar of the supplied file
and name check and header verification of the resulting contents.
To form a factory.bin that is accepted by OEM Openwrt build,
the kernel and rootfs must have specific names...
openwrt-senao-ens202ext-uImage-lzma.bin
openwrt-senao-ens202ext-root.squashfs
and begin with the respective headers (uImage, squashfs).
Then the files must be tarballed and gzipped.
The resulting binary is actually a tar.gz file in disguise.
This can be verified by using binwalk on the OEM firmware images,
ungzipping then untaring, and by swapping headers to see
what the OEM upgrade utility accepts and rejects.
Note on the factory.bin:
The newest kernel is too large to be in the kernel partition
the new ath79 kernel is beyond 1592k
Even ath79-tiny is 1580k
Checksum fails at boot because the bootloader (modified uboot)
expects kernel to be 1536k. If the kernel is larger, it gets
overwritten when rootfs is flashed, causing a broken image.
The mtdparts variable is part of the build and saving a new
uboot environment will not persist after flashing.
OEM version might interact with uboot or with the custom
OEM partition at 0x9f050000.
Failed checksums at boot cause failsafe image to launch,
allowing any image to be flashed again.
HOWEVER: one should not install older Openwrt from failsafe
because it can cause rootfs to be unmountable,
causing kernel loop after successful checksum.
The only way to rescue after that is with a serial cable.
For these reasons, a fake kernel (OKLI kernel loader)
and fake squashfs rootfs is implemented to take care of
the OEM firmware image verification and checksums at boot.
The OEM only verifies the checksum of the first image
of each partition respectively, which is the loader
and the fake squashfs. This completely frees
the "firmware" partition from all checks.
virtual_flash is implemented to make use of the wasted space.
this leaves only 2 erase blocks actually wasted.
The loader and fakeroot partitions must remain intact, otherwise
the next boot will fail, redirecting to the Failsafe image.
Because the partition table required is so different
than the OEM partition table and ar71xx partition table,
sysupgrades are not possible until one switches to ath79 kernel.
Note on sysupgrade.tgz:
To make things even more complicated, another change is needed to
fix an issue where network does not work after flashing from either
OEM software or Failsafe image, which implants the OEM (Openwrt Kamikaze)
configuration into the jffs2 /overlay when writing rootfs from factory.bin.
The upgrade script has this:
mtd -j "/tmp/_sys/sysupgrade.tgz" write "${rootfs}" "rootfs"
However, it also accepts scripts before and after:
before_local="/etc/before-upgradelocal.sh"
after_local="/etc/after-upgradelocal.sh"
before="before-upgrade.sh"
after="after-upgrade.sh"
Thus, we can solve the issue by making the .tgz an empty file
by making a before-upgrade.sh in the factory.bin
Note on built-in switch:
There is two ports on the board, POE through the power supply brick,
the other is on the board. For whatever reason, in the ar71xx target,
both ports were on the built-in switch on eth1. In order to make use
of a port for WAN or a different LAN, one has to set up VLANs.
In ath79, eth0 and eth1 is defined in the DTS so that the
built-in switch is seen as eth0, but only for 1 port
the other port is on eth1 without a built-in switch.
eth0: switch0
CPU is port 0
board port is port 1
eth1: POE port on the power brick
Since there is two physical ports,
it can be configured as a full router,
with LAN for both wired and wireless.
According to the Datasheet, the port that is not on the switch
is connected to gmac0. It is preferred that gmac0 is chosen as WAN
over a port on an internal switch, so that link status can pass
to the kernel immediately which is more important for WAN connections.
Signed-off-by: Michael Pratt <mpratt51@gmail.com>
[apply sorting in 01_leds, make factory recipe more generic, create common
device node, move label-mac to 02_network, add MAC addresses to commit
message, remove kmod-leds-gpio, use gzip directly]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This network setup for MikroTik devices based on the LHG-HB platform
avoids using the integrated switch and connects the single Ethernet
port directly. This way, link speed (10/100 Mbps) is properly repor-
ted by eth0.
Fixes: FS#3309
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
The base address is used for the LAN and 2G WLAN interfaces.
5G WLAN interface is +1 and the PLC interface uses +2.
Signed-off-by: Sven Wegener <sven.wegener@stealer.net>
[improve commit title, fix assignment in 11-ath10k-caldata]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Port device support for Meraki MR16 from the ar71xx target to ath79.
Specifications:
* AR7161 CPU, 16 MiB Flash, 64 MiB RAM
* One PoE-capable Gigabit Ethernet Port
* AR9220 / AR9223 (2x2 11an / 11n) WLAN
Installation:
* Requires TFTP server at 192.168.1.101, w/ initramfs & sysupgrade .bins
* Open shell case and connect a USB to TTL cable to upper serial headers
* Power on the router; connect to U-boot over 115200-baud connection
* Interrupt U-boot process to boot Openwrt by running:
setenv bootcmd bootm 0xbf0a0000; saveenv;
tftpboot 0c00000 <filename-of-initramfs-kernel>.bin;
bootm 0c00000;
* Copy sysupgrade image to /tmp on MR16
* sysupgrade /tmp/<filename-of-sysupgrade>.bin
Notes:
- There are two separate ARTs in the partition (offset 0x1000/0x5000 and
0x11000/0x15000) in the OEM device. I suspect this is an OEM artifact;
possibly used to configure the radios for different regions,
circumstances or RF frontends. Since the ar71xx target uses the
second offsets, use that second set (0x11000 and 0x15000) for the ART.
- kmod-owl-loader is still required to load the ART partition into the
driver.
- The manner of storing MAC addresses is updated from ar71xx; it is
at 0x66 of the 'config' partition, where it was discovered that the
OEM firmware stores it. This is set as read-only. If you are
migrating from ar71xx and used the method mentioned above to
upgrade, use kmod-mtd-rw or UCI to add the MAC back in. One more
method for doing this is described below.
- Migrating directly from ar71xx has not been thoroughly tested, but
one method has been used a couple of times with good success,
migrating 18.06.2 to a full image produced as of this commit. Please
note that these instructions are only for experienced users, and/or
those still able to open their device up to flash it via the serial
headers should anything go wrong.
1) Install kmod-mtd-rw and uboot-envtools
2) Run `insmod mtd-rw.ko i_want_a_brick=1`
3) Modify /etc/fw_env.config to point to the u-boot-env partition.
The file /etc/fw_env.config should contain:
# MTD device env offset env size sector size
/dev/mtd1 0x00000 0x10000 0x10000
See https://openwrt.org/docs/techref/bootloader/uboot.config
for more details.
4) Run `fw_printenv` to verify everything is correct, as per the
link above.
5) Run `fw_setenv bootcmd bootm 0xbf0a0000` to set a new boot address.
6) Manually modify /lib/upgrade/common.sh's get_image function:
Change ...
cat "$from" 2>/dev/null | $cmd
... into ...
(
dd if=/dev/zero bs=1 count=$((0x66)) ; # Pad the first 102 bytes
echo -ne '\x00\x18\x0a\x12\x34\x56' ; # Add in MAC address
dd if=/dev/zero bs=1 count=$((0x20000-0x66-0x6)) ; # Pad the rest
cat "$from" 2>/dev/null | $cmd
)
... which, during the upgrade process, will pad the image by
128K of zeroes-plus-MAC-address, in order for the ar71xx's
firmware partition -- which starts at 0xbf080000 -- to be
instead aligned with the ath79 firmware partition, which
starts 128K later at 0xbf0a0000.
7) Copy the sysupgrade image into /tmp, as above
8) Run `sysupgrade -F /tmp/<sysupgrade>.bin`, then wait
Again, this may BRICK YOUR DEVICE, so make *sure* to have your
serial cable handy.
Addenda:
- The MR12 should be able to be migrated in a nearly identical manner as
it shares much of its hardware with the MR16.
- Thank-you Chris B for copious help with this port.
Signed-off-by: Martin Kennedy <hurricos@gmail.com>
[fix typo in compat message, drop art DT label,
move 05_fix-compat-version to subtarget]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The kernel has become too big again for the ar9344-based TP-Link
CPE/WBS devices which still have no firmware-partition splitter.
Current buildbots produce a kernel size of about 2469 kiB, while
the partition is only 2048 kiB (0x200000). Therefore, increase it
to 0x300000 to provide enough room for this and, hopefully, the
next kernel.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
On Comfast CF-E130N v2 and Mikrotik LHG HB board, the config
found in DTS appears to be strange:
- eth0 has "syscon","simple-mfd" set although it's not enabled
- eth1 is enabled redundantly (already "okay" in qca953x.dtsi)
- phy-handle is set for eth1 in DTS although it has a fixed-link
in qca953x.dtsi
This seems like a copy-paste gone wrong. Remove the named options.
Run-tested on MikroTik LHG 2.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
For many target we have added CONFIG_WATCHDOG_CORE=y to the target
config due to the following error:
Package kmod-hwmon-sch5627 is missing dependencies for the following
libraries:
watchdog.ko
However, actually the proper way appears to be setting the
dependency for the kmod-hwmon-sch5627 package, as the error message
demands.
Do this in this patch and remove the target config entries added
due to this issue.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The TL-WPA8630 v1 and v2 have the same LED Control GPIO configuration
according to the TP-Link GPL sources. Set the GPIO to output to make
it work and set to Active Low. It defaults to LEDs on at bootup.
To turn all LEDs off:
echo 0 > /sys/class/gpio/tp-link\:led\:control/value
To turn all LEDs on:
echo 1 > /sys/class/gpio/tp-link\:led\:control/value
Change the "LED" button from BTN_0 to KEY_LIGHTS_TOGGLE to match other
devices and the button guide, and to reduce the number of unintuitive
"BTN_X" inputs.
Fixes: ab74def0db ("ath79: add support for TP-Link TL-WPA8630P v2")
Signed-off-by: Joe Mullally <jwmullally@gmail.com>
[shorten commit title, minor commit message adjustments]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This adds support for the TP-Link TL-WR710N v2.1. It is basically a
re-issue of the v1.2.
Specifications:
SoC: Atheros AR9331
CPU: 400 MHz
Flash: 8 MiB
RAM: 32 MiB
WiFi: 2.4 GHz b/g/n
Ethernet: 2x 100M ports
USB: 1x 2.0
The only difference from the v1 is the TP-Link hardware ID/revision.
Attention:
The TL-WR710N v2.0 (!) has only 4 MB flash and cannot be flashed with
this image. It has a different TPLINK_HWREV, so accidental flashing
of the factory image should be impossible without additional measures.
Unfortunately, the v2.0 in ar71xx has the same board name, so sysupgrade
from ar71xx v2.0 into ath79 v1/v2.1 will not be prevented, but will brick
the device.
Flashing instruction:
Upload the factory image via the OEM firmware GUI upgrade mechanism.
Further notes:
To make implementation easier if somebody desires to port the 4M v2.0,
this already creates two DTSI files.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Fabian Eppig <fabian@eppig.de>
In order to support SAE/WPA3-Personal in default images. Replace almost
all occurencies of wpad-basic and wpad-mini with wpad-basic-wolfssl for
consistency. Keep out ar71xx from the list as it won't be in the next
release and would only make backports harder.
Build-tested (build-bot settings):
ath79: generic, ramips: mt7620/mt76x8/rt305x, lantiq: xrx200/xway,
sunxi: a53
Signed-off-by: Petr Štetiar <ynezz@true.cz>
[rebase, extend commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This PR is a blend of several kernel bumps authored by ldir taken from his
staging tree w/ some further adjustments made by me and update_kernel.sh
Summary:
Deleted upstreamed patches:
generic:
742-v5.5-net-sfp-add-support-for-module-quirks.patch
743-v5.5-net-sfp-add-some-quirks-for-GPON-modules.patch
bcm63xx:
022-v5.8-mtd-rawnand-brcmnand-correctly-verify-erased-pages.patch
024-v5.8-mtd-rawnand-brcmnand-fix-CS0-layout.patch
mediatek:
0402-net-ethernet-mtk_eth_soc-Always-call-mtk_gmac0_rgmii.patch
Deleted patches applied differently upstream:
generic:
641-sch_cake-fix-IP-protocol-handling-in-the-presence-of.patch
Manually merged patches:
generic:
395-v5.8-net-sch_cake-Take-advantage-of-skb-hash-where-appropriate.patch
bcm27xx:
950-0132-lan78xx-Debounce-link-events-to-minimize-poll-storm.patch
layerscape:
701-net-0231-enetc-Use-DT-protocol-information-to-set-up-the-port.patch
Build system: x86_64
Build-tested: ath79/generic, bcm27xx/bcm2708, bcm27xx/bcm2711,
imx6, mvebu/cortexa9, sunxi/a53
Run-tested: Netgear R7800 (ipq806x)
No dmesg regressions, everything functional
Signed-off-by: John Audia <graysky@archlinux.us>
Tested-By: Lucian Cristian <Lucian.cristian@gmail.com> [mvebu]
Tested-By: Curtis Deptuck <curtdept@me.com> [x86/64]
[do not remove 395-v5.8-net-sch_cake-Take-advantage-... patch,
adjust and refresh patches, adjust commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-By: John Audia <graysky@archlinux.us> [ipq806x]
On Mikrotik SPI NOR devices, the firmware partition must be erased when
flashing from stock firmware, otherwise leftover bits (in particular a
kernel signature) can trigger a boot loop.
When booted from initramfs (the only way to install OpenWRT on these
devices), this patch unconditionally erases the firmware partition in
the do_upgrade() stage for all supported SPI NOR devices.
This is forward-ported from ed49d0876 and 20452a8db
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
The node needs to be terminated by a semicolon.
Fixes: 8484a764df ("ath79: ar724x: make sure builtin-switch is
enabled in DT")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Both TL-WPA8630(P) v1 and v2 feature a button labelled "WiFi".
While this is implemented as KEY_RFKILL for v1 in ar71xx and ath79,
the v2 sets it up as WPS button.
According to the manual, the behavior in OEM firmware is:
"Press and hold the button for 1 second to copy wireless settings
from the main router to the extender. Go to Wi-Fi Clone for more
information. Press and hold the button for at least 5 seconds to
turn the wireless function on or off."
Consequently, and since this is historic behavior on v1 in OpenWrt,
we set this button to KEY_RFKILL on both revisions.
Fixes: ab74def0db ("ath79: add support for TP-Link TL-WPA8630P v2")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
On ar7240/ar7241 the mdioX node with the builtin-switch is enabled
in the DTSI files, but the parent ethX node is left disabled. It
only gets enabled per device or device family, and has not been
enabled at all yet for the TP-Link WA devices with ar7240, making
the switch unavailable there.
This patch makes sure ð0/ð1 nodes are enabled together with
the &mdio0/&mdio1 nodes containing the builtin-switch.
For ar7240_tplink_tl-wa.dtsi, ð0 is properly hidden again via
compatible = "syscon", "simple-mfd";
This partially fixes FS#2887, however it seems dmesg still does
not show cable (dis)connect in dmesg for ar7240 TP-Link WA
devices.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
ALLNET ALL-WAP02860AC is a dual-band wireless access point.
Specification
SoC: Qualcomm Atheros QCA9558
RAM: 128 MB DDR2
Flash: 16 MB SPI NOR
WIFI: 2.4 GHz 3T3R integrated
5 GHz 3T3R QCA9880 Mini PCIe card
Ethernet: 1x 10/100/1000 Mbps AR8035-A, PoE capable (802.3at)
LEDS: 5x, which four are GPIO controlled
Buttons: 1x GPIO controlled
UART: 4 pin header near Mini PCIe card, starting count from white
triangle on PCB
1. VCC 3.3V, 2. GND, 3. TX, 4. RX
baud: 115200, parity: none, flow control: none
MAC addresses
Calibration data does not contain valid MAC addresses.
The calculated MAC addresses are chosen in accordance with OEM firmware.
Because of:
a) constrained environment (SNMP) when connecting through Telnet
or SSH,
b) hard-coded kernel and rootfs sizes,
c) checksum verification of kerenel and rootfs images in bootloder,
creating factory image accepted by OEM web interface is difficult,
therefore, to install OpenWrt on this device UART connection is needed.
The teardown is simple, unscrew four screws to disassemble the casing,
plus two screws to separate mainboard from the casing.
Before flashing, be sure to have a copy of factory firmware, in case You
wish to revert to original firmware.
Installation
1. Prepare TFTP server with OpenWrt initramfs-kernel image.
2. Connect to LAN port.
3. Connect to UART port.
4. Power on the device and when prompted to stop autoboot, hit any key.
5. Alter U-Boot environment with following commands:
setenv failsafe_boot bootm 0x9f0a0000
saveenv
6. Adjust "ipaddr" and "serverip" addresses in U-Boot environment, use
'setenv' to do that, then run following commands:
tftpboot 0x81000000 <openwrt_initramfs-kernel_image_name>
bootm 0x81000000
7. Wait about 1 minute for OpenWrt to boot.
8. Transfer OpenWrt sysupgrade image to /tmp directory and flash it
with:
sysupgrade -n /tmp/<openwrt_sysupgrade_image_name>
9. After flashing, the access point will reboot to OpenWrt. Wait few
minutes, until the Power LED stops blinking, then it's ready for
configuration.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
[add MAC address comment to commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This ports the TP-Link TL-WPA8630 v1 from ar71xx to ath79.
Specifications:
SoC: QCA9563
CPU: 750 MHz
Flash/RAM: 8 / 128 MiB
Ethernet: 3x 1G ports (QCA8337 switch)
WLAN: 2.4 GHz b/g/n, 5 GHz a/n/ac (ath10k)
Buttons, LEDs and network setup appear to be almost identical
to the v2 revision.
Powerline interface is connected to switch port 5 (Label LAN4).
Installation:
No "fresh" device was available for testing the factory image.
It is not known whether flashing via OEM firmware GUI is possible
or not. A discussion from 2018 [1] about that indicates a few
adjustments are necessary, but it is not clear whether those
are already implemented with the TPLINK_HEADER_VERSION = 2 or not.
Note that for the TL-WPA8630P v1, the TPLINK_HWID needs to be
changed to 0x86310001 to allow factory flashing.
[1] https://forum.openwrt.org/t/solved-tl-wpa8630p-lede-does-not-install/8161/27
Recovery:
Recovery is only possible via serial.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The commands to read ath9k caldata on mikrotik subtarget are
mostly repetitive, so let's put them into a function to make
writing and reading them easier.
This function will only be required when patching the MAC address.
For cases where it is put correctly into the calibration data by
the vendor, caldata_sysfsload_from_file can be used directly as
done for ath10k at the moment.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The missing "size" property was acceptable in the context of a single
DTS as the underlying device is known to have a 64KB flash, and thus
the bios partition fit exactly between the preceding and following ones.
However as this block has moved in a DTSI, for the sake of clarity and
explicitness the size property is added to ensure that if the flash
happens to be larger than expected, the bios partition remains properly
sized.
Suggested-by: Thibaut VARÈNE <hacks@slashdirt.org>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This harmonizes the appearance of ethX nodes in qca953x DTSes by:
- having the same order of nodes and properties
- removing redundant status property on eth1 (set in qca953x.dtsi)
This is meant to help both copy-pasters and reviewers, since
deviations and errors can be spotted easier.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The MikroTik SXT Lite5 (product code RBSXT5nDr2, also SXT 5nD r2) is
an outdoor 5GHz CPE with a 16 dBi integrated antenna built around the
Atheros AR9344 SoC. It is based on the "sxt5n" board platform.
Specifications:
- SoC: Atheros AR9344
- RAM: 64 MB
- Storage: 128 MB NAND
- Wireless: Atheros AR9340 (SoC) 802.11a/n 2x2:2
- Ethernet: Atheros AR8229 switch (SoC), 1x 10/100 port,
8-32 Vdc PoE in
- 6 user-controllable LEDs:
· 1x power (blue)
· 1x wlan (green)
· 4x rssi (green)
- 1 GPIO-controlled buzzer
See https://mikrotik.com/product/RBSXT5nDr2 for more details.
Notes:
The device was already supported in the ar71xx target. There, the
Ethernet port was handled by GMAC1. Here in ath79 it is handled by
GMAC0, which allows to get link information (loss, speed, duplex) on
the eth0 interface.
Flashing:
TFTP boot initramfs image and then perform sysupgrade. Follow common
MikroTik procedure as in https://openwrt.org/toh/mikrotik/common.
Acknowledgments:
Michael Pratt (@mpratt14) for helping on the network settings.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
[rebase, use mikrotik LED label prefix, make names consistent,
add reg for bootloader2, use led_user for boot indication etc.,
minor cosmetic changes]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The MikroTik RouterBOARD 921GS-5HPacD-15s (mANTBox 15s) is an outdoor
antenna for 5 GHz with an built-in router. This ports the board from
ar71xx.
See https://mikrotik.com/product/RB921GS-5HPacD-15S for more info.
Specifications:
- SoC: Qualcomm Atheros QCA9558 (720 MHz)
- RAM: 128 MB
- Storage: 128 MB NAND
- Wireless: external QCA9892 802.11a/ac 2x2:2
- Ethernet: 1x 1000/100/10 Mbps, integrated, via AR8031 PHY, passive PoE in
- SFP: 1x host
Working:
- NAND storage detection
- Ethernet
- Wireless
- 1x user LED (blinks during boot, sysupgrade)
- Reset button
- Sysupgrade
Untested:
- SFP cage (probably not working)
Installation (untested):
- Boot initramfs image via TFTP and then flash sysupgrade image
As the embedded RB921-pcb is a stripped down version of the RB922 this patch
adds a common dtsi for this series and includes this to the final dts-files.
Signed-off-by: Sven Roederer <devel-sven@geroedel.de>
[move ath10k-leds closer to ath10k definition in DTS files]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The MikroTik RouterBOARD LHG 2nD (sold as LHG 2) is a 2.4 GHz
802.11b/g/n outdoor device with a feed and an integrated dual
polarization grid dish antenna based on the LHG-HB platform.
See https://mikrotik.com/product/lhg_2 for more info.
Specifications:
- SoC: Qualcomm Atheros QCA9533
- RAM: 64 MB
- Storage: 16 MB NOR
- Wireless: Atheros AR9531 (SoC) 802.11b/g/n 2x2:2, 18 dBi antenna
- Ethernet: Atheros AR8229 (SoC), 1x 10/100 port, 12-28 Vdc PoE in
- 8 user-controllable LEDs:
· 1x power (blue)
· 1x user (green)
· 1x lan (green)
· 1x wlan (green)
· 4x rssi (green)
Note:
The rssihigh LED is disabled, as it shares GPIO 16 with the reset
button.
Flashing:
TFTP boot initramfs image and then perform sysupgrade. Follow common
MikroTik procedure as in https://openwrt.org/toh/mikrotik/common.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
[rebase, remove rssiled setup, adjust commit message, add DTSIs]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Specifications:
SoC: Qualcomm Atheros QCA9557
RAM: 128 MB (Nanya NT5TU32M16EG-AC)
Flash: 16 MB (Macronix MX25L12845EMI-10G)
Ethernet: 5x 10/100/1000 (1x WAN, 4x LAN)
Wireless: QCA9557 2.4GHz (nbg), QCA9882 5GHz (ac)
USB: 2x USB 2.0 port
Buttons: 1x Reset
Switches: 1x Wifi
LEDs: 11 (Pwr, WAN, 4x LAN, 2x Wifi, 2x USB, WPS)
MAC addresses:
WAN *:3f uboot-env ethaddr + 3
LAN *:3e uboot-env ethaddr + 2
2.4GHz *:3c uboot-env ethaddr
5GHz *:3d uboot-env ethaddr + 1
The label contains all four MAC addresses, however the one without
increment is first, so this one is taken for label MAC address.
Notes:
The Wifi is controlled by an on/off button, i.e. has to be implemented
by a switch (EV_SW). Despite, it appears that GPIO_ACTIVE_HIGH needs
to be used, just like recently fixed for the NBG6716.
Both parameters have been wrong at ar71xx.
Flash Instructions:
At first the U-Boot variables need to be changed in order to boot the
new combined image format. ZyXEL uses a split kernel + root setup and
the current kernel is too large to fit into the partition. As resizing
didnt do the trick, I've decided to use the prefered combined image
approach to be future-kernel-enlargement-proof (thanks to blocktrron for
the assistance).
First add a new variable called boot_openwrt:
setenv boot_openwrt bootm 0x9F120000
After that overwrite the bootcmd and save the environment:
setenv bootcmd run boot_openwrt
saveenv
After that you can flash the openwrt factory image via TFTP. The servers
IP has to be 192.168.1.33. Connect to one of the LAN ports and hold the
WPS Button while booting. After a few seconds the NBG6616 will look for
a image file called 'ras.bin' and flash it.
Return to vendor firmware is possible by resetting the bootcmd:
setenv bootcmd run boot_flash
saveenv
and flashing the vendor image via the TFTP method as described above.
Accessing the U-Boot Shell:
ZyXEL uses a proprietary loader/shell on top of u-boot: "ZyXEL zloader v2.02"
When the device is starting up, the user can enter the the loader shell
by simply pressing a key within the 3 seconds once the following string
appears on the serial console:
| Hit any key to stop autoboot: 3
The user is then dropped to a locked shell.
| NBG6616> ?
| ATEN x,(y) set BootExtension Debug Flag (y=password)
| ATSE x show the seed of password generator
| ATSH dump manufacturer related data in ROM
| ATRT (x,y,z,u) ATRT RAM read/write test (x=level, y=start addr, z=end addr, u=iterations
| ATGO boot up whole system
| ATUR x upgrade RAS image (filename)
In order to escape/unlock a password challenge has to be passed.
Note: the value is dynamic! you have to calculate your own!
First use ATSE $MODELNAME (MODELNAME is the hostname in u-boot env)
to get the challange value/seed.
| NBG6616> ATSE NBG6616
| 00C91D7EAC3C
This seed/value can be converted to the password with the help of this
bash script (Thanks to http://www.adslayuda.com/Zyxel650-9.html authors):
- tool.sh -
ror32() {
echo $(( ($1 >> $2) | (($1 << (32 - $2) & (2**32-1)) ) ))
}
v="0x$1"
a="0x${v:2:6}"
b=$(( $a + 0x10F0A563))
c=$(( 0x${v:12:14} & 7 ))
p=$(( $(ror32 $b $c) ^ $a ))
printf "ATEN 1,%X\n" $p
- end of tool.sh -
| # bash ./tool.sh 00C91D7EAC3C
| ATEN 1,10FDFF5
Copy and paste the result into the shell to unlock zloader.
| NBG6616> ATEN 1,10FDFF5
If the entered code was correct the shell will change to
use the ATGU command to enter the real u-boot shell.
| NBG6616> ATGU
| NBG6616#
Signed-off-by: Christoph Krapp <achterin@googlemail.com>
[move keys to DTSI, adjust usb_power DT label, remove kernel config
change, extend commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
A bunch of kernel modules depends on kmod-usb-net, but does not
select it. Make AddDepends/usb-net selective, so we can drop
some redundant +kmod-usb-net definitions for DEVICE_PACKAGES.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
SPI Flash chip supports up to 33 MHz wihout fast read opcode.
Available frequencies are 112.5, 56.25, 37.5, 28.125, 22.5 etc.
This patch increases the nominal maximum frequency to 33 MHz,
reaching an effective increase from 22.5 to 28.125 MHz.
Formula to calculate SPI frequency:
Freq = 225 MHz / 2 / div
Before:
$ time dd if=/dev/mtd1 of=/dev/null bs=8M
0+1 records in
0+1 records out
real 0m 3.58s
user 0m 0.00s
sys 0m 3.57s
After:
$ time dd if=/dev/mtd1 of=/dev/null bs=8M
0+1 records in
0+1 records out
real 0m 2.95s
user 0m 0.00s
sys 0m 2.93s
Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
[minor commit message adjustments]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The TL-WPA8630P v2 is a HomePlug AV2 compatible device with a QCA9563 SoC
and 2.4GHz and 5GHz WiFi modules.
Specifications
--------------
- QCA9563 750MHz, 2.4GHz WiFi
- QCA9888 5GHz WiFi
- 8MiB SPI Flash
- 128MiB RAM
- 3 GBit Ports (QCA8337)
- PLC (QCA7550)
MAC address assignment
----------------------
WiFi 2.4GHz and LAN share the same MAC address as printed on the label.
5GHz WiFi uses LAN-1, based on assumptions from similar devices.
LAN Port assignment
-------------------
While there are 3 physical LAN ports on the device, there will be 4
visible ports in OpenWrt. The fourth port (internal port 5) is used
by the PowerLine Communication SoC and thus treated like a regular
LAN port.
Versions
--------
Note that both TL-WPA8630 and TL-WPA8630P, as well as the different
country-versions, differ in partitioning, and therefore shouldn't be
cross-flashed.
This adds support for the two known partitioning variants of the
TL-WPA8630P, where the variants can be safely distinguished via the
tplink-safeloader SupportList. For the non-P variants (TL-WPA8630),
at least two additional partitioning schemes exist, and the same
SupportList entry can have different partitioning.
Thus, we don't support those officially (yet).
Also note that the P version for Germany (DE) requires the international
image version, but is properly protected by SupportList.
In any case, please check the OpenWrt Wiki pages for the device
before flashing anything!
Installation
------------
Installation is possible from the OEM web interface. Make sure to
install the latest OEM firmware first, so that the PLC firmware is
at the latest version. However, please also check the Wiki page
for hints according to altered partitioning between OEM firmware
revisions.
Additional thanks to Jon Davies and Joe Mullally for bringing
order into the partitioning mess.
Signed-off-by: Andreas Böhler <dev@aboehler.at>
[minor DTS adjustments, add label-mac-device, drop chosen, move
common partitions to DTSI, rename de to int, add AU support strings,
adjust TPLINK_BOARD_ID, create common node in generic-tp-link.mk,
adjust commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This ports support for the TL-WA901ND v3 from ar71xx to ath79.
Most of the hardware is shared with the TL-WA850/860RE v1 range
extenders. It completes the TL-WA901ND series in ath79.
Specifications:
Board: AP123 / AR9341
Flash/RAM: 4/32 MiB
CPU: 535 MHz
WiFi: 2.4 GHz b/g/n
Ethernet: 1 port (100M)
Flashing instructions:
Upload the factory image via the vendor firmware upgrade option.
This has not been tested on device, but port from ar71xx is
straightforward and the device will be disabled by default anyway.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The ath79 target has CONFIG_LEDS_GPIO=y set in kernel config, so
no need to pull the kmod-leds-gpio module for specific devices.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This patch adds support for the WNDR4300TN, marketed by Belgian ISP
Telenet. The hardware is the same as the WNDR4300 v1, without the
fifth ethernet port (WAN) and the USB port. The circuit board has
the traces, but the components are missing.
Specifications:
* SoC: Atheros AR9344
* RAM: 128 MB
* Flash: 128 MB NAND flash
* WiFi: Atheros AR9580 (5 GHz) and AR9344 (2.4 GHz)
* Ethernet: 4x 1000Base-T
* LED: Power, LAN, WiFi 2.4GHz, WiFi 5GHz, WPS
* UART: on board, to the right of the RF shield at the top of the board
Installation:
* Flashing through the OEM web interface:
+ Connect your computer to the router with an ethernet cable and browse
to http://192.168.0.51/
+ Log in with the default credentials are admin:password
+ Browse to Advanced > Administration > Firmware Upgrade in the Telenet
interface
+ Upload the Openwrt firmware: openwrt-ath79-nand-netgear_wndr4300tn-squashfs-factory.img
+ Proceed with the firmware installation and give the device a few
minutes to finish and reboot.
* Flashing through TFTP:
+ Configure your wired client with a static IP in the 192.168.1.x range,
e.g. 192.168.1.10 and netmask 255.255.255.0.
+ Power off the router.
+ Press and hold the RESET button (the factory reset button on the bottom
of the device, with the gray circle around it, next to the Telenet logo)
and turn the router on while keeping the button pressed.
+ The power LED will start flashing orange. You can release the button
once it switches to flashing green.
+ Transfer the image over TFTP:
$ tftp 192.168.1.1 -m binary -c put openwrt-ath79-nand-netgear_wndr4300tn-squashfs-factory.img
Signed-off-by: Davy Hollevoet <github@natox.be>
[use DT label reference for adding LEDs in DTSI files]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Move the image preparation and nand-utils package selection into
common device definitions for NOR/NAND devices.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The gl-e750 is a portable travel router that gives you safe access to
the internet while traveling.
Specifications:
- SoC: Qualcomm Atheros AR9531 (650MHz)
- RAM: 128 MB DDR2
- Flash: 16 MB SPI NOR (W25Q128FVSG) + 128 MB SPI NAND (GD5F1GQ4UFYIG)
- Ethernet: 10/100: 1xLAN
- Wireless: QCA9531 2.4GHz (bgn) + QCA9887 5GHz (ac)
- USB: 1x USB 2.0 port
- Switch: 1x switch
- Button: 1x reset button
- OLED Screen: 128*64 px
MAC addresses based on vendor firmware:
LAN *:a0 art 0x0
2.4GHz *:a1 art 0x1002
5GHz *:a2 art calculated from art 0x0 + 2
Flash firmware:
Since openwrt's kernel already exceeds 2MB, upgrading from the official
version of GL-inet (v3.100) using the sysupgrade command will break the
kernel image. Users who are using version 3.100 can only upgrade via
uboot. The official guidance for GL-inet is as follows:
https://docs.gl-inet.com/en/3/troubleshooting/debrick/
In the future, GL-inet will modify the firmware to support the sysupgrade
command, so users will be able to upgrade directly with the sysupgrade
command in future releases.
OLED screen control:
OLED controller is connected to QCA9531 through serial port, and can send
instructions to OLED controller directly through serial port.
Refer to the links below for a list of supported instructions:
https://github.com/gl-inet/GL-E750-MCU-instruction
Signed-off-by: Luochongjun <luochongjun@gl-inet.com>
[fix alphabetic sorting in 10-fix-wifi-mac, drop check-kernel-size]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
It has been decided that the 19.07 release will be last one to include
4/32 devices.
This disables default build for the remaining devices with 4M flash
on ath79. Note that this will leave exactly one enabled device for
ath79/tiny subtarget, PQI Air-Pen, which was moved there due to
kernel size restrictions.
All 4M TP-Link devices have already been disabled in
8819faff47 ("ath79: do not build TP-Link tiny images by default")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Netgear currently has a special definition for tiny devices, which
is only used by two devices. Despite, it sets ups the IMAGE/default
definition individually for all devices, although there is actually
only one exception.
This merges the common parts into a single netgear_generic definition
(in contrast to netgear_ath79_nand), and adjusts the individual
definitions accordingly.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Specifications:
SoC: QCA9563
DRAM: 128MB DDR2
Flash: 16MB SPI-NOR
2 Gigabit ethernet ports
3×3 2.4GHz on-board radio
miniPCIe slot that supports 5GHz radio
PoE 24V passive or 36V-56V passive with optional IEEE 802.3af/at
USB 3.0 header
Installation:
To install, either start tftp in bin/targets/ath79/generic/ and use
the u-boot prompt over UART:
tftpboot 0x80500000 openwrt-ath79-generic-compex_wpj563-squashfs-sysupgrade.bin
erase 0x9f680000 +1
erase 0x9f030000 +$filesize
cp.b $fileaddr 0x9f030000 $filesize
boot
The cpximg file can be used with sysupgrade in the stock firmware (add
SSH key in luci for root access) or with the built-in cpximg loader.
The cpximg loader can be started either by holding the reset button
during power up or by entering the u-boot prompt and entering 'cpximg'.
Once it's running, a TFTP-server under 192.168.1.1 will accept the image
appropriate for the board revision that is etched on the board.
For example, if the board is labelled '7A02':
tftp -v -m binary 192.168.1.1 -c put openwrt-ath79-generic-compex_wpj563-squashfs-cpximg-7a02.bin
MAC addresses:
<&uboot 0x2e010> *:71 (label)
<&uboot 0x2e018> *:72
<&uboot 0x2e020> *:73
<&uboot 0x2e028> *:74
Only the first two are used (for ethernet), the WiFi modules have
separate (valid) addresses. The latter two addresses are not used.
Signed-off-by: Leon M. George <leon@georgemail.eu>
The Mikrotik RBwAPG-5HacT2HnD has only a single ethernet interface
(lan), and the vendor uses the base (label) MAC address for it.
Signed-off-by: Bjoern Dobe <bjoern@dobecom.de>
[commit title/message improvement]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
AR8327 datasheet[1] calls the register at address 0x0010
"Power-on Strapping Register". As it has nothing to do with "strip",
let's rename it to "POWER_ON_STRAP" to make it easier to grasp.
[1] https://lafibre.info/images/doc/201106_spec_AR8327.pdf
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
The bootloader only writes the first 2MB of the image to the NOR flash
when installing the NAND factory image. The bootloader is capable of
booting larger kernels as it boots from the memory mapped SPI flash.
Disable the NAND factory image. The NAND can be bootstrapped by writing
the NAND initramfs image using the NOR upgrade method in the bootloader
web-recovery and sysupgrading from there. The NOR variant is not
affected.
Also refactor the partition definitions in the DTS to make them less
annoying to read.
Signed-off-by: David Bauer <mail@david-bauer.net>
The TL-WR841ND v8 feature a WiFi switch instead of a button.
This adds the corresponding input-type to prevent booting into
failsafe regularly.
This has been defined correctly in ar71xx, but was overlooked
when migrating to ath79. In contrast, the TL-WR842ND v2, which
has the key set up as switch in ar71xx, actually has a button.
The TL-MR3420 v2 has a button as well and is set up correctly
for both targets. (Information based on TP-Link user guide)
Note:
While looking into this, I found that support PR for TL-MR3420 v2
switched reset button to ACTIVE_HIGH. However, the other two
device still use ACTIVE_LOW. This seems strange, but I cannot
verify it lacking the affected devices.
Fixes: FS#2733
Fixes: 9601d94138 ("add support for TP-Link TL-WR841N/ND v8")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This harmonizes the model names for the ath79 Ubiquiti devices by
applying a few minor cosmetic adjustments:
- Removes hyphens where they are not found in the product names
(Ubiquiti uses hyphens only for the abbreviated version names
like UAP-AC-PRO which we don't use anyway.)
- Add (XM) suffix for DTS model strings to help with distinguishing
them from their XW counterparts.
- Remove DEVICE_VARIANT for LAP-120 which actually was an alternate
device name.
- Generally make DTS model names and those from generic-ubnt.mk
more consistent.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This adds support for the Ubiquiti PowerBridge M, which has the same
board/LEDs as the Bullet M XM, but different case and antennas.
Specifications:
- AR7241 SoC @ 400 MHz
- 64 MB RAM
- 8 MB SPI flash
- 1x 10/100 Mbps Ethernet, 24 Vdc PoE-in
- Internal antenna: 25 dBi
- POWER/LAN green LEDs
- 4x RSSI LEDs (red, orange, green, green)
- UART (115200 8N1) on PCB
Flashing via WebUI:
Upload the factory image via the stock firmware web UI.
Attention: airOS firmware versions >= 5.6 have a new bootloader with
an incompatible partition table!
Please downgrade to <= 5.5 _before_ flashing OpenWrt!
Refer to the device's Wiki page for further information.
Flashing via TFTP:
Same procedure as other Bullet M (XM) boards.
- Use a pointy tool (e.g., pen cap, paper clip) and keep the reset
button on the device or on the PoE supply pressed
- Power on the device via PoE (keep reset button pressed)
- Keep pressing until LEDs flash alternatively LED1+LED3 =>
LED2+LED4 => LED1+LED3, etc.
- Release reset button
- The device starts a TFTP server at 192.168.1.20
- Set a static IP on the computer (e.g., 192.168.1.21/24)
- Upload via tftp the factory image:
$ tftp 192.168.1.20
tftp> bin
tftp> trace
tftp> put openwrt-ath79-generic-xxxxx-ubnt_powerbridge-m-squashfs-factory.bin
Signed-off-by: Vieno Hakkerinen <vieno@hakkerinen.eu>
Since commit 6f2e1b7485 (ath79: disable delays on AT803X config init)
the incoming incoming traffic on the ubnt,lap-120 devices Ethernet
port was not making it through. Using rgmii-id instead of rgmii (same
configuration as ubnt,litebeam-ac-gen2) fixes it.
Fixes FS#2893.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
upstream changed dt-bindings for marvell 88e6060 to use mdio-device
and dropped support for legacy bindings.
fix it in our local dts.
Fixes: FS#2524
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Linux phy subsystem provides support for a phy regulator defined via
phy-supply property. Use it to turn on usb power only when usb is
probed.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
The support for this device's Marvell MV88E6060 switch has been
reported to be broken with kernels 4.19/5.4 (see bug report).
Since this a 4/32 device and it has been confirmed to be working
with stable 19.07 release (kernel 4.14), and since fixing it does
not seem trivial, let's just disable it in master.
Fixes: FS#2524
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Port device support for DAP-1330 from the ar71xx target to ath79.
Additionally, images are generated for the European through-socket
case variant DAP-1365. Both devices run the same vendor firmware, the
only difference being the DAP_SIGNATURE field in the factory header.
The vendor's Web UI will display a model string stored in the flash.
Specifications:
* QCA9533, 8 MiB Flash, 64 MiB RAM
* One Ethernet Port (10/100)
* Wall-plug style case (DAP-1365 with additional socket)
* LED bargraph RSSI indicator
Installation:
* Web UI: http://192.168.0.50 (or different address obtained via DHCP)
There is no password set by default
* Recovery Web UI: Keep reset button pressed during power-on
until LED starts flashing red, upgrade via http://192.168.0.50
* Some modern browsers may have problems flashing via the Web UI,
if this occurs consider booting to recovery mode and flashing via:
curl -F \
files=@openwrt-ath79-generic-dlink_dap-1330-a1-squashfs-factory.bin \
http://192.168.0.50/cgi/index
The device will use the same MAC address for both wired and wireless
interfaces, however it is stored at two different locations in the flash.
Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
Arduino Yun is a microcontroller development board, based on Atmel
ATmega32u4 and Atheros AR9331.
Specifications:
- MCU: ATmega32U4
- SoC: AR9331
- RAM: DDR2 64MB
- Flash: SPI NOR 16MB
- WiFi:
- 2.4GHz: SoC internal
- Ethernet: 1x 10/100Mbps
- USB: 1x 2.0
- MicroSD: 1x SDHC
Notes:
- Stock firmware is based on OpenWrt AA.
- The SoC UART can be accessed only through the MCU.
YunSerialTerminal is recommended for access to serial console.
- Stock firmware uses non-standard 250000 baudrate by default.
- The MCU can be reprogrammed from the SoC with avrdude linuxgpio.
Installation:
1. Update U-Boot environment variables to adapt to new partition scheme.
> setenv bootcmd "run addboard; run addtty; run addparts; run addrootfs; bootm 0x9f050000 || bootm 0x9fea0000"
> setenv mtdparts "spi0.0:256k(u-boot)ro,64k(u-boot-env),15936k(firmware),64k(nvram),64k(art)ro"
> saveenv
2. Boot into stock firmware normally and perform sysupgrade with
sysupgrade image.
# sysupgrade -n -F /tmp/sysupgrade.bin
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
The DCH-G020 is a Smart Home Gateway for Z-Wave devices.
Specifications:
* QCA9531, 16 MiB Flash, 64 MiB RAM
* On-Board USB SD3503A Z-Wave dongle
* GL850 USB 2.0 Hub (one rear port, internal Z-Wave)
* Two Ethernet Ports (10/100)
Installation:
* Web UI: http://192.168.0.60 (or different address obtained via DHCP)
Login with 'admin' and the 6-digit PIN Code from the bottom label
* Recovery Web UI: Keep reset button pressed during power-on
until LED starts flashing red, upgrade via http://192.168.0.60
* Some modern browsers may have problems flashing via the Web UI,
if this occurs consider booting to recovery mode and flashing via:
curl -F \
files=@openwrt-ath79-generic-dlink_dch-g020-a1-squashfs-factory.bin \
http://192.168.0.60/cgi/index
Known issues:
* Real-Time-Clock is not working as there is currently no matching driver
It is still included in the dts as compatible = "pericom,pt7c43390";
* openzwave was tested on v19.07 (running MinOZW as a proof-of-concept),
but the package grew too big as lots of device pictures were included,
thus any use of Z-Wave is up to the user (e.g. extroot and domoticz)
The device will use the same MAC address for both wired and wireless
interfaces, however it is stored at two different locations in the flash.
Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
Specification:
• 650/600/216 MHz (CPU/DDR/AHB)
• 64 MB of RAM (DDR2)
• 32 MB of FLASH
• 2T2R 2.4 GHz
• 2x 10/100 Mbps Ethernet
• 1x USB 2.0 Host socket
• 1x miniPCIe slot
• UART for serial console
• 14x GPIO
Flash instructions:
Upgrading from ar71xx target:
• Upload image into the board:
scp openwrt-ath79-generic-8dev_lima-squashfs-sysupgrade.bin
root@192.168.1.1/tmp/
• Run sysupgrade
sysupgrade -F /tmp/openwrt-ath79-generic-8dev_lima-squashfs-sysupgrade.bin
Upgrading from u-boot:
• Set up tftp server with
openwrt-ath79-generic-8dev_lima-initramfs-kernel.bin
• Go to u-boot (reboot and press ESC when prompted)
• Set TFTP server IP
setenv serverip 192.168.1.254
• Set device ip from the same subnet
setenv ipaddr 192.168.1.1
• Copy new firmware to board
tftpboot 0x82000000 initramfs.bin
• Boot OpenWRT
bootm 0x82000000
• Upload image openwrt-ath79-generic-8dev_lima-squashfs-sysupgrade.bin into
the board
• Run sysupgrade.
Signed-off-by: Andrey Bondar <a.bondar@8devices.com>
Fixes following build failures:
WARNING: Image file glinet_gl-ar750s-nor-kernel.bin is too big
WARNING: Image file glinet_gl-ar750s-nor-nand-kernel.bin is too big
Signed-off-by: Petr Štetiar <ynezz@true.cz>
As the reported major bugs are ironed out, switch to the new kernel to
begin testing with a broader audience.
Signed-off-by: David Bauer <mail@david-bauer.net>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Fixes:
- CVE-2020-10757
The "mtd: rawnand: Pass a nand_chip object to nand_release()" commit was
backported which needed some adaptations to other code.
Run tested: ath79
Build tested: ath79
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add support for the ar71xx supported GL.iNet GL-MiFi to ath79.
Specifications:
- Atheros AR9331
- 64 MB of RAM
- 16 MB of FLASH (SPI NOR)
- 2x 10/100/1000 Mbps Ethernet
- 2.4GHz (AR9330), 802.11b/g/n
- 1x USB 2.0 (vbus driven by GPIO)
- 4x LED, driven by GPIO
- 1x button (reset)
- 1x mini pci-e slot (vcc driven by GPIO)
Flash instructions:
Vendor software is based on openwrt so you can flash the sysupgrade
image via the vendor GUI or using command line sysupgrade utility.
Make sure to not save configuration over reflash as uci settings
differ between versions.
Note on MAC addresses:
Even though the platform is capable to providing separate MAC addresses
to the interfaces vendor firmware does not seem to take advantage of
that. It appears that there is only single unique pre-programmed
address in the art partition and vendor firmware uses that for
every interface (eth0/eth1/wlan0). Similar behaviour has also been
implemented in this patch.
Note on GPIOs:
In vendor firmware the gpio controlling mini pci-e slot is named
3gcontrol while it actually controls power supply to the entire mini
pci-e slot. Therefore a more descriptive name (minipcie) was chosen.
Also during development of this patch it became apparent that the
polarity of the signal is actually active low rather than active high
that can be found in vendor firmware.
Acknowledgements:
This patch is based on earlier work[1] done by Kyson Lok. Since the
initial mailing-list submission the patch has been modified to comply
with current openwrt naming schemes and dts conventions.
[1] http://lists.openwrt.org/pipermail/openwrt-devel/2018-September/019576.html
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
All definitions of gpio in SoC DTSI files do not set status, i.e.
have it enabled. This drops all remaining redundant "status = okay"
definitions in descendent files (mostly older ones).
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
All other SoC DTSI files have gpio enabled by default, only
ar9330/ar9331 disable it by default, only to have it enabled again
afterwards for each individual device.
So, do not disable it in the first place, and drop all device-specific
status statements afterwards.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Specifications:
SoC: AR9344
DRAM: 128MB DDR2
Flash: 16MB SPI-NOR
2 Gigabit ethernet ports
2×2 2.4GHz on-board radio
miniPCIe slot that supports 5GHz radio
PoE 48V IEEE 802.3af/at - 24V passive optional
USB 2.0 header
Installation:
To install, either start tftp in bin/targets/ath79/generic/ and use
the u-boot prompt over UART:
tftpboot 0x80500000 openwrt-ath79-generic-compex_wpj344-16m-squashfs-sysupgrade.bin
erase 0x9f030000 +$filesize
erase 0x9f680000 +1
cp.b $fileaddr 0x9f030000 $filesize
boot
The cpximg file can be used with sysupgrade in the stock firmware (add
SSH key in luci for root access) or with the built-in cpximg loader.
The cpximg loader can be started either by holding the reset button
during power up or by entering the u-boot prompt and entering 'cpximg'.
Once it's running, a TFTP-server under 192.168.1.1 will accept the image
appropriate for the board revision that is etched on the board.
For example, if the board is labelled '6A08':
tftp -v -m binary 192.168.1.1 -c put openwrt-ath79-generic-compex_wpj344-16m-squashfs-cpximg-6a08.bin
MAC addresses:
<&uboot 0x2e010> *:99 (label)
<&uboot 0x2e018> *:9a
<&uboot 0x2e020> *:9b
<&uboot 0x2e028> *:9c
Only the first two are used (for ethernet), the WiFi modules have
separate (valid) addresses. The latter two addresses are not used.
Signed-off-by: Leon M. George <leon@georgemail.eu>
[minor commit message adjustments, drop gpio in DTS, DTS style fixes,
sorting, drop unused cpximg recipe]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The replaces the custom uImageArcher build step with the generic uImage
build step. The only different between these two is the difference in
the generated name.
Tested on: TP-Link Archer C59 v1
Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: David Bauer <mail@david-bauer.net>
For quite some time, the tiny (4M flash) TP-Link sysupgrade and
factory images cannot be built anymore by the buildbots, just
the initramfs-kernel.bin files are still there.
Disable these images for the buildbots and prevent useless builds.
Note that these devices still build fine with default settings,
even for kernel 5.4.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Generate additional images that are compatible to the cpximg loader.
The cpximg loader can be started either by holding the reset button during
power up or by entering the u-boot prompt and entering 'cpximg'.
Once it's running, a TFTP-server under 192.168.1.1 will accept the image
appropriate for the board revision that is etched on the board.
For example, if the board is labelled '7A04':
tftp -v -m binary 192.168.1.1 -c put openwrt-ath79-generic-compex_wpj531-16m-squashfs-cpximg-7A04.bin
These files can also be used with the sysupgrade utility in stock images (add
SSH key in luci for root access).
Signed-off-by: Leon M. George <leon@georgemail.eu>
[fix sorting of definitions]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Specifications:
SoC: QCA9531
DRAM: 128MB DDR2
Flash: 16MB SPI-NOR
2 100MBit ethernet ports
2×2 2.4GHz on-board radio
miniPCIe slot that supports 5GHz radio
PoE 24V - 48V IEEE 802.3af optional
USB 2.0 header
Installation:
To install, start a tftp server in bin/targets/ath79/generic/ and use the
u-boot prompt over UART:
tftpboot 0x80500000 openwrt-ath79-generic-compex_wpj531-16m-squashfs-sysupgrade.bin
erase 0x9f030000 +$filesize
erase 0x9f680000 +1
cp.b $fileaddr 0x9f030000 $filesize
boot
The cpximg file can be used with sysupgrade in the stock firmware (add SSH key
in luci for root access).
Another way is to hold the reset button during power up or running 'cpximg' in
the u-boot prompt.
Once the last LED starts flashing regularly, a TFTP-server under 192.168.1.1
will accept the image appropriate for the board revision that is etched on the
board.
For example, if the board is labelled '7A04':
tftp -v -m binary 192.168.1.1 -c put openwrt-ath79-generic-compex_wpj531-16m-squashfs-cpximg-7A04.bin
MAC addresses:
<&uboot 0x2e010> *:cb (label)
<&uboot 0x2e018> *:cc
<&uboot 0x2e020> *:cd
<&uboot 0x2e028> *:ce
Only the first two are used (for ethernet), the WiFi modules have
separate (valid) addresses. The latter two addresses are not used.
Signed-off-by: Leon M. George <leon@georgemail.eu>
[commit title/message facelift, fix rssileds, add led aliases]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
switch-bcm53xx-mdio does not exists, use kmod-switch-bcm53xx-mdio
instead.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Tobias Schramm <tobleminer@gmail.com>
In ath79, for several SoCs the console bootargs are defined to the
very same value in every device's DTS. Consolidate these definitions
in the SoC dtsi files and drop further redundant definitions elsewhere.
The only device without any bootargs set has been OpenMesh OM5P-AC V2.
This will now inherit the setting from qca955x.dtsi
Note that while this tidies up master a lot, it might develop into a
frequent pitfall for backports.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This commit adds support for the AVM FRITZ!WLAN Repeater DVB-C
SOC: Qualcomm Atheros QCA9556
RAM: 64 MiB
FLASH: 16 MB SPI-NOR
WLAN: QCA9556 3T3R 2.4 GHZ b/g/n and
QCA9880 3T3R 5 GHz n/ac
ETH: Atheros AR8033 1000 Base-T
DVB-C: EM28174 with MaxLinear MXL251 tuner
BTN: WPS Button
LED: Power, WLAN, TV, RSSI0-4
Tested and working:
- Ethernet (correct MAC, gigabit, iperf3 about 200 Mbit/s)
- 2.4 GHz Wi-Fi (correct MAC)
- 5 GHz Wi-Fi (correct MAC)
- WPS Button (tested using wifitoggle)
- LEDs
- Installation via EVA bootloader (FTP recovery)
- OpenWrt sysupgrade (both CLI and LuCI)
- Download of "urlader" (mtd0)
Not working:
- Internal USB
- DVB-C em28174+MxL251 (depends on internal USB)
Installation via EVA bootloader (FTP recovery):
Set NIC to 192.168.178.3/24 gateway 192.168.178.1 and power on the device,
connect to 192.168.178.1 through FTP and sign in with adam2/adam2:
ftp> quote USER adam2
ftp> quote PASS adam2
ftp> binary
ftp> debug
ftp> passive
ftp> quote MEDIA FLSH
ftp> put openwrt-sysupgrade.bin mtd1
Wait for "Transfer complete" together with the transfer details.
Wait two minutes to make sure flash is complete (just to be safe).
Then restart the device (power off and on) to boot into OpenWrt.
Revert your NIC settings to reach OpenWrt at 192.168.1.1
Signed-off-by: Natalie Kagelmacher <nataliek@pm.me>
[fixed sorting - removed change to other board -
prettified commit message]
Signed-off-by: David Bauer <mail@david-bauer.net>
Currently it's not possible to tftpboot initramfs image on archer-c7-v5
as the image contains tplink-v1-header which leads to:
ath> bootm
## Booting image at 81000000 ...
Bad Magic Number
as U-Boot expects uImage wrapped image. This is caused by following
inheritance issue:
define Device/Init
KERNEL_INITRAMFS = $$(KERNEL)
define Device/tplink-v1
KERNEL := kernel-bin | append-dtb | lzma
KERNEL_INITRAMFS := kernel-bin | append-dtb | lzma | tplink-v1-header
define Device/tplink-safeloader
$(Device/tplink-v1)
define Device/tplink-safeloader-uimage
$(Device/tplink-safeloader)
KERNEL := kernel-bin | append-dtb | lzma | uImageArcher lzma
define Device/tplink_archer-c7-v5
$(Device/tplink-safeloader-uimage)
where tplink-v1 defines KERNEL_INITRAMFS with tplink-v1-header and it's
then used by all devices inheriting from tplink-safeloader. Fix this by
overriding KERNEL_INITRAMFS to KERNEL variable again.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Inputs assigned to "mode select" switch on the side of the device
were missing linux,input-type property.
This would cause them do incorrectly generate EV_KEY events.
Fix this by setting the linux,input-type = <EV_SW> property on them.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
TP-Link CPE610 v2 is an outdoor wireless CPE for 5 GHz with
one Ethernet port based on Atheros AR9344
Specifications:
- 560/450/225 MHz (CPU/DDR/AHB)
- 1x 10/100 Mbps Ethernet
- 64 MB of DDR2 RAM
- 8 MB of SPI-NOR Flash
- 23dBi high-gain directional 2×2 MIMO antenna and a
dedicated metal reflector
- Power, LAN, WLAN5G green LEDs
- 3x green RSSI LEDs
Flashing instructions:
Flash factory image through stock firmware WEB UI
or through TFTP
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254
Signed-off-by: Andrew Cameron <apcameron@softhome.net>
This ports support for these devices from ar71xx.
Specification:
- System-On-Chip: Qualcomm Atheros QCA9533
- CPU/Speed: v3: 560 MHz, v4: 650 MHz
- Flash: 4096 KiB
- RAM: 32 MiB
- Ethernet: 1 port @ 100M
- Wireless: SoC-integrated: QCA9533 2.4GHz 802.11bgn
In contrast to the implementation in ar71xx (reset and WiFi button),
the device actually features reset and WPS buttons.
Flashing instructions:
Upload the ...-factory.bin file via OEM web interface.
TFTP Recovery:
1. Set PC to fixed IP address 192.168.0.66
2. Download *-factory.bin image and rename it to
wa801ndv3_tp_recovery.bin
3. Start a tftp server with the image file in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
the firmware should be transferred from the tftp server
8. Wait ~30 second to complete recovery.
TFTP recovery has only been tested with v3, and the Wiki states
that the procedure won't work for v4, which cannot be verified
or falsified at the moment.
Tested by Tim Ward (see forum):
https://forum.openwrt.org/t/ath79-support-for-tp-link-tl-wa901nd-v3-v4-v5/61246/13
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The status is set to "okay" for all devices on ar9344, so just move
this to the parent DTSI.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Define the kernel config symbol CONFIG_MFD_RB4XX_CPLD=n
to fix build breakage on non-mikrotik targets.
The driver was added for all ath79, but the symbol was only
defined for mikrotik subtarget.
Fixes: fa70b3a4bb ("ath79: add Mikrotik rb4xx series drivers")
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
[rearrange commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Specifications:
- SoC: Atheros AR9344
- RAM: 64MB
- Storage: 8 MB SPI NOR
- Wireless: 2.4GHz N based built into SoC
- Ethernet: 1x 10/100 Mbps with 24V POE IN, 1x 10/100 Mbps
Installation:
Flash factory image through stock firmware WEB UI
or through TFTP
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This drops the shebang from all target files for /lib and
/etc/uci-defaults folders, as these are sourced and the shebang
is useless.
While at it, fix the executable flag on a few of these files.
This does not touch ar71xx, as this target is just used for
backporting now and applying cosmetic changes would just complicate
things.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This patch adds support for the MikroTik RouterBOARD RB493G, ported
from the ar71xx target.
See https://routerboard.com/RB493G for details
Specification:
- SoC Qualcomm Atheros AR7161
- RAM: 256 MiB
- Storage: 128MiB NAND
- Ethernet: 9x 1000/100/10 Mbps
- USB 1x 2.0 / 1.0 type A
- PCIe: 3x Mini slot
- MicroSD slot
Working:
- Board/system detection
- Ethernet
- SPI
- NAND
- LEDs
- USB
- Sysupgrade
Enabled (but untested due to lack of hardware):
- PCIe - ath79_pci_irq struct has the slot/pin/IRQ mappings if needed
Installation methods:
- tftp boot initramfs image, scp then flash via "sysupgrade -n"
- nand boot existing OpenWrt, scp then flash via "sysupgrade -n"
Notes:
- initramfs image will not work if uncompressed image size over ~8.5Mb
- The "rb4xx" drivers have been enabled
Signed-off-by: Christopher Hill <ch6574@gmail.com>
This adds 3 Mikrotik rb4xx series drivers as follows:
rb4xx-cpld: This is in the mfd subsystem, and is the parent CPLD device
that interfaces between the SoC SPI bus and its two children below.
rb4xx-gpio: This is the GPIO expander.
rb4xx-nand: This is the NAND driver.
The history of this code comes in three phases.
1. The first is a May 2015 attempt to push the equivalient ar71xx rb4xx
drivers upstream. See https://lore.kernel.org/patchwork/patch/940880/.
Module-author: Gabor Juhos <juhosg@openwrt.org>
Module-author: Imre Kaloz <kaloz@openwrt.org>
Module-author: Bert Vermeulen <bert@biot.com>
2. Next several ar71xx patches were applied bringing the code current.
commit 7bbf4117c6
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
commit af79fdbe4a
commit 889272d92d
commit e21cb649a2
commit 7c09fa4a74
Signed-off-by: Felix Fietkau <nbd@nbd.name>
3. Finally a heavy refactor to split the driver into the three new
subsystems, and updated to work with the device tree configuration, plus
updates and review feedback incorporated
Reviewed-by: Thibaut VARÈNE <hacks@slashdirt.org>
Signed-off-by: Christopher Hill <ch6574@gmail.com>
Currently, ag71xx will trigger a warning when TX xor RX-Delay modes are
enabled.
Handle them identical to the already implemented RGMII modes, as they
are only different for the attached PHY.
Signed-off-by: David Bauer <mail@david-bauer.net>
Hardware:
* SoC: Qualcomm Atheros QCA9558
* RAM: 256MB
* Flash: 16MB SPI NOR
* Ethernet: 2x 10/100/1000 (1x 802.3at PoE-PD)
* WiFi 2.4GHz: Qualcomm Atheros QCA9558
* WiFi 5GHz: Qualcomm Ahteros QCA9880-2R4E
* LEDS: 1x 5GHz, 1x 2.4GHz, 1x LAN1(POE), 1x LAN2, 1x POWER
* Buttons: 1x RESET
* UART: 1x RJ45 RS-232 Console port
Installation via stock firmware:
* Install the factory image via the stock firmware web interface
Installation via bootloader Emergency Web Server:
* Connect your PC to the LAN1(PoE) port
* Configure your PC with IP address 192.168.0.90
* Open a serial console to the Console port (115200,8n1)
* Press "q" within 2s when "press 'q' to stop autoboot" appears
* Open http://192.168.0.50 in a browser
* Upload either the factory or the sysupgrade image
* Once you see "write image into flash...OK,dest addr=0x9f070000" you
can power-cycle the device. Ignore "checksum bad" messages.
Setting the MAC addresses for the ethernet interfaces via
/etc/board.d/02_network adds the following snippets to
/etc/config/network:
config device 'lan_eth0_1_dev'
option name 'eth0.1'
option macaddr 'xx:xx:xx:xx:xx:xx'
config device 'wan_eth1_2_dev'
option name 'eth1.2'
option macaddr 'xx:xx:xx:xx:xx:xx'
This would result in the proper MAC addresses being set for the VLAN
subinterfaces, but the parent interfaces would still have a random MAC
address. Using untagged VLANs could solve this, but would still leave
those extra snippets in /etc/config/network, and then the device VLAN
setup would differ from the one used in ar71xx. Therefore, the MAC
addresses of the ethernet interfaces are being set via preinit instead.
The bdcfg partition contains 4 MAC address labels:
- lanmac
- wanmac
- wlanmac
- wlanmac_a
The first 3 all contain the same MAC address, which is also the one on
the label.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Reviewed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Many target use a repetitive if-include scheme for their subtarget
image files, though their names are consistent with the subtarget
names.
This patch removes these redundant conditions and just uses the
variable for the include where the target setup allows it.
For sunxi, this includes a trivial rename of the subtarget image
Makefiles.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The Netgear WNDRMAC v1 is a hardware variant of the Netgear WNDR3700 v2
Specifications
==============
* SoC: Atheros AR7161
* RAM: 64mb
* Flash on board: 16mb
* WiFi: Atheros AR9220 (a/n), Atheros AR9223 (b/g/n)
* Ethernet: RealTek RTL8366SR (1xWAN, 4xLAN, Gigabit)
* Power: 12 VDC, 2.5 A
* Full specs on [openwrt.org](https://openwrt.org/toh/hwdata/netgear/netgear_wndrmac_v1)
Flash Instructions
==================
It is possible to use the OEM Upgrade page to install the `factory`
variant of the firmware.
After the initial upgrade, you will need to telnet into the router
(default IP 192.168.1.1) to install anything. You may install LuCI
this way. At this point, you will have a web interface to configure
OpenWRT on the WNDRMAC v1.
Please use the `sysupgrade` variant for subsequent flashes.
Recovery Instructions
=====================
A TFTP-based recovery flash is possible if the need arises. Please refer
to the WNDR3700 page on openwrt.org for details.
https://openwrt.org/toh/netgear/wndr3700#troubleshooting_and_recovery
Signed-off-by: Renaud Lepage <root@cybikbase.com>
[update DTSI include name]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The Netgear WNDRMAC v2 is a hardware variant of the Netgear WNDR3800
Specifications
==============
* SoC: Atheros AR7161
* RAM: 128mb
* Flash on board: 16mb
* WiFi: Atheros AR9220 (a/n), Atheros AR9223 (b/g/n)
* Ethernet: RealTek RTL8366SR (1xWAN, 4xLAN, Gigabit)
* Serial console: Yes, 115200 / 8N1 (JTAG)
* USB: 1x2.0
* Power: 12 VDC, 2.5 A
* Full specs on [openwrt.org](https://openwrt.org/toh/hwdata/netgear/netgear_wndrmac_v2)
Flash Instructions
==================
It is possible to use the OEM Upgrade page to install the `factory`
variant of the firmware.
After the initial upgrade, you will need to telnet into the router
(default IP 192.168.1.1) to install anything. You may install LuCI
this way. At this point, you will have a web interface to configure
OpenWRT on the WNDRMAC v2.
Please use the `sysupgrade` variant for subsequent flashes.
Recovery Instructions
=====================
A TFTP-based recovery flash is possible if the need arises. Please refer
to the WNDR3800 page on openwrt.org for details.
https://openwrt.org/toh/netgear/wndr3800#recovery_flash_in_failsafe_mode
Signed-off-by: Renaud Lepage <root@cybikbase.com>
[do not add device to uboot-envtools, update DTSI name]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This renames the DTSI for Netgear WNDR devices based on ar7161 to
indicate that the file is not limited to WNDR3700 models.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This patch adds ar71xx's GPIO setup for the 2.4GHz and 5GHz antennae
demultiplexer:
| 158 /* 2.4 GHz uses the first fixed antenna group (1, 0, 1, 0) */
| 159 ap9x_pci_setup_wmac_gpio(0, (0xf << 6), (0xa << 6));
| 160
| 161 /* 5 GHz uses the second fixed antenna group (0, 1, 1, 0) */
| 162 ap9x_pci_setup_wmac_gpio(1, (0xf << 6), (0x6 << 6));
This should restore the range and throughput of the 2.4GHz radio
on all the derived wndr3700 variants and versions with the AR7161 SoC.
A special case is the 5GHz radio. The original wndr3700(v1) will
benefit from this change. However the wndr3700v2 and later revisions
were unaffected by the missing bits, as there is no demultiplexer
present in the later designs.
This patch uses gpio-hogs within the device-tree for all
wndr3700/wndr3800/wndrmac variants.
Notes:
Based on the PCB pictures, the WNDR3700(v1) really had eight
independent antennae. Four antennae for each radio and all of
those were printed on the circut board.
The WNDR3700v2 and later have just six antennae. Four of those
are printed on the circuit board and serve the 2.4GHz radio.
Whereas the remaining two are special 5GHz Rayspan Patch Antennae
which are directly connected to the 5GHz radio.
Hannu Nyman dug pretty deep and unearthed a treasure of information
regarding the history of how these values came to be in the OpenWrt
archives: <https://dev.archive.openwrt.org/ticket/6533.html>.
Mark Mentovai came across the fixed antenna group when he was looking
into the driver:
fixed_antenna_group 1, (0, 1, 0, 1)
fixed_antenna_group 2, (0, 1, 1, 0)
fixed_antenna_group 3, (1, 0, 0, 1)
fixed_antenna_group 4, (1, 0, 1, 0)
Fixes: FS#3088
Reported-by: Luca Bensi
Reported-by: Maciej Mazur
Reported-by: Hannu Nyman <hannu.nyman@iki.fi>
Debugged-by: Hannu Nyman <hannu.nyman@iki.fi>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This is only a cosmetic correction, as the driver works as expected.
However, the error message confuses users about a missing reset definition.
On a defered init we don't see the following error message now:
[ 0.078292] ar7200-usb-phy usb-phy: phy reset is missing
Tested-by: Lech Perczak <lech.perczak@gmail.com>
Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>
TP-Link RE450 v3 is a dual band router/range-extender based on
Qualcomm/Atheros QCA9563 + QCA9880.
This device is nearly identical to RE450 v2 besides a modified flash
layout (hence I think force-flashing a RE450v2 image will lead to at
least loss of MAC address).
Specification:
- 775 MHz CPU
- 64 MB of RAM (DDR2)
- 8 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 3T3R 5 GHz
- 1x 10/100/1000 Mbps Ethernet (AR8033 PHY)
- 7x LED, 4x button-
- possible UART header on PCB¹
Flash instruction:
Apply factory image in OEM firmware web-gui.
¹ Didn't check to connect as I didn't even manage to connect on
RE450v2 (AFAIU it requires disconnecting some resistors, which I was
too much of a coward to do). But given the similarities to v2 I
think it's the same or very similar procedure (and most likely also
the only way to debrick).
Signed-off-by: Andreas Wiese <aw-openwrt@meterriblecrew.net>
[remove dts-v1 and compatible in DTSI]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Specification:
- SoC: Qualcomm Atheros QCA9533 (560 MHz, MIPS 24Kc)
- RAM: 32 MiB
- Storage: 4 MiB of Flash on board
- Wireless: Built into QCA9533 (Honey Bee), PHY modes b/g/n
- Ethernet: 1x100M (port0)
Installation through OEM Web Interface:
- Connect to TL-WR802N by Ethernet or Wi-Fi
- Go to web interface:
[V1] http://192.168.0.1
[V2] http://192.168.0.254
Default user is "admin" & password is "admin".
On V2, there is no DHCP server running by default, so remember to set
IP manually.
- Go to "System Tools -> Firmware Upgrade"
- Browse for firmware:
[V1] "*.factory.bin"
[V2] "*.factory-us.bin" or "*.factory-eu.bin" for eu model
Web interface may complain if filename is too long. In such case,
rename .bin to something shorter.
- Click upgrade
Installation through tftp:
Note: T_OUT, T_IN and GND on the board must be connected to USB TTL
Serial Configuration 115200 8n1
- Boot the TL-WR802N
- When "Autobooting in 1 seconds" appears type "tpl" followed by enter
- Connect to the board Ethernet port
(IPADDR: 192.168.1.1, ServerIP: 192.168.1.10)
- tftpboot 0x80000000 <Firmware Image Name>
- Record the result of "printenv bootcmd"
- Enter "erase <Result of 'printenv bootcmd'> +0x3c0000"
(e.g erase 0x9f020000 +0x3c0000)
- Enter "cp.b 0x80000000 <Result of 'printenv bootcmd'> 0x3c0000"
(e.g cp.b 0x80000000 0x9f020000 0x3c0000)
- Enter "bootm <Result of 'printenv bootcmd'>"
(e.g bootm 0x9f020000)
Notes:
When porting from ar71xx target to ath79, I found out that on V2,
reset button is on GPIO12 and active low, instead of GPIO11 and
active high. By cross-flashing V1 firmware to V2, I confirmed
the same is true for V1.
Also according to manual of V1, this one also has green
LED instead of blue - both of those issues were fixed accordingly.
The MAC address assignment has been checked with OEM firmware.
Installation manual based on ar71xx support by Thomas Roberts
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
[slightly adjust commit message, add MAC address comment]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Ubiquiti WA devices with newer hw version 2011K require UBNT_VERSION
to be at least 8.5.3, otherwise the image is rejected:
New ver: WA.ar934x.v8.5.0-42.OpenWrt-r10947-65030d81f3
Versions: New(525568) 8.5.0, Required(525571) 8.5.3
Invalid version 'WA.ar934x.v8.5.0-42.OpenWrt-r10947-65030d81f3'
For consistency, also increase version number for XC devices.
Tested-by: Pedro <pedrowrt@cas.cat>
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Since the wireless LED was used for boot and set up with a DT
trigger, the WiFi indication hasn't worked on ath79 at all.
In addition, a look into the manual revealed that the OEM
configuration is as follows:
LED 1 (green): power
LED 2 (green): configurable
LED 3 (red): wireless
So, let's just keep the WiFi trigger and convert the rest to its
"intended" use.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This patch adds support for the COMFAST CF-E130N v2, an outdoor wireless
CPE with a single Ethernet port and a 802.11bgn radio.
Specifications:
- QCA9531 SoC
- 1x 10/100 Mbps Ethernet with PoE-in support
- 64 MB of RAM (DDR2)
- 16 MB of FLASH
- 5 dBi built-in antenna
- POWER/LAN/WLAN green LEDs
- 4x RSSI LEDs (2x red, 2x green)
- UART (115200 8N1) and GPIO (J9) headers on PCB
Flashing instructions:
The original firmware is based on OpenWrt so a sysupgrade image can be
installed via the stock web GUI.
The U-boot bootloader also contains a backup TFTP client to upload the
firmware from. Upon boot, it checks its ethernet network for the IP
192.168.1.10. Host a TFTP server and provide the image to be flashed as
file firmware_auto.bin.
MAC address setup:
The art partition contains four consecutive MAC addresses:
0x0 aa:bb:cc:xx:xx:c4
0x6 aa:bb:cc:xx:xx:c6
0x1002 aa:bb:cc:xx:xx:c5
0x5006 aa:bb:cc:xx:xx:c7
However, the manufacturer in its infinite wisdom decided that one address
is enough and both eth0 and WiFi get the MAC address from 0x0 (yes, that's
overwriting the existing and valid address in 0x1002). This is obviously
also the address on the device's label.
Signed-off-by: Pavel Balan <admin@kryma.net>
[fix configs partition, fix IMAGE_SIZE, add MAC address comment, rename
ATH_SOC to SOC]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
AHB is 258 MHz for this device (CPU_PLL / 3), but there is no difference
between 64 MHz and 50 MHz for spi-max-frequency, thus increase to 50 MHz.
Tested on revisions C1 and C3.
Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
GPIO 11 needs to be pulled high for the external gigabit switch to work,
this is currently solved via gpio-hog. Replace with phy0 reset-gpios.
Tested on revisions C1 and C3. Reset button is still working for reboot,
to enter failsafe, and to enter bootloader http recovery.
Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
The device has a total of 8 LEDs, 5 of which are controlled by the switch
(LAN 1-4, WAN). Only power, wifi and wps are controlled by the SoC.
* led_power is on GPIO 5 (not 15), boot flashing sequence is now visible
* remove led 'internet', since it is only connected to the switch
* remove ucidef_set_led_switch for WAN from 01_leds, as it has no effect
Tested on revisions C1 and C3.
Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
[adjust commit title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The UBIFS_FS_ZSTD is exposed when UBIFS is enabled.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
[adjust commit title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Between 4.19 and 5.4, the kernel moved the partition parsers into
the parsers subdirectory. This led to some necessary rebasing of
our local patches for parsers, which partially has been performed
without caring about where the code was inserted.
This commit tries to adjust our local patches so that parsers are
inserted at the "proper" positions with respect to alphabetic sorting
(if possible). Thus, the commit is cosmetic.
While this might look useless now, it will make life easier when
adding other parsers in the future or for rebasing on kernel changes.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This patch adds support for the WNDR4300SW, marketed by California ISP
SureWest (hence the 'SW' suffix). Hardware wise, it's identical to the
WNDR4300 v1.
Specifications:
* SoC: Atheros AR9344
* RAM: 128 MB
* Flash: 128 MB NAND flash
* WiFi: Atheros AR9580 (5 GHz) and AR9344 (2,4 GHz)
* Ethernet: 5x 1000Base-T
* LED: Power, WAN, LAN, WiFi, USB, WPS
* UART: on board, to the right of the RF shield at the top of the board
Installation:
* Flashing through the OEM web interface:
+ Connect your computer to the router with an ethernet cable and browse
to http://192.168.1.1/
+ Log in with the default credentials are admin:password
+ Browse to Advanced > Administration > Firmware Upgrade in the Netgear
interface
+ Upload the Openwrt firmware: openwrt-ath79-nand-netgear_wndr4300sw-squashfs-factory.img
+ Proceed with the firmware installation and give the device a few
minutes to finish and reboot.
* Flashing through TFTP:
+ Configure your wired client with a static IP in the 192.168.1.x range,
e.g. 192.168.1.10 and netmask 255.255.255.0.
+ Power off the router.
+ Press and hold the RESET button (the factory reset button on the bottom
of the device, with the red circle around it) and turn the router on
while keeping the button pressed.
+ The power LED will start flashing orange. You can release the button
once it switches to flashing green.
+ Transfer the image over TFTP:
$ tftp 192.168.1.1 -m binary -c put openwrt-ath79-nand-netgear_wndr4300sw-squashfs-factory.img
Signed-off-by: Stijn Segers <foss@volatilesystems.org>
Hardware
--------
SoC: Atheros AR9344
RAM: 128M DDR2
FLASH: 2x Macronix MX25L12845EM
2x 16MiB SPI-NOR
WLAN2: Atheros AR9344 2x2 2T2R
WLAN5: Atheros AR9580 2x2 2T2R
SERIAL: Cisco-RJ45 on the back (115200 8n1)
Installation
------------
The U-Boot CLI is password protected (using the same credentials as the
OS). Default is admin/new2day.
1. Download the OpenWrt initramfs-image. Place it into a TFTP server
root directory and rename it to 1401A8C0.img. Configure the TFTP
server to listen at 192.168.1.66/24.
2. Connect the TFTP server to the access point.
3. Connect to the serial console of the access point. Attach power and
interrupt the boot procedure when prompted (bootdelay is 1 second).
4. Configure the U-Boot environment for booting OpenWrt from Ram and
flash:
$ setenv boot_openwrt 'setenv bootargs; bootm 0xbf230000'
$ setenv ramboot_openwrt 'setenv serverip 192.168.1.66;
tftpboot 0x85000000; bootm'
$ setenv bootcmd 'run boot_openwrt'
$ saveenv
5. Load OpenWrt into memory:
$ run ramboot_openwrt
Wait for the image to boot.
6. Transfer the OpenWrt sysupgrade image to the device. Write the image
to flash using sysupgrade:
$ sysupgrade -n /path/to/openwrt-sysuograde.bin
Signed-off-by: David Bauer <mail@david-bauer.net>
This ports support for the TL-WA901ND v4 and v5 from ar71xx to ath79.
They are similar to the TP9343-based TL-WR940N v3/v4 and TL-WR941ND v6.
Specifications:
SoC: TP9343
Flash/RAM: 4/32 MiB
CPU: 750 MHz
WiFi: 2.4 GHz b/g/n
Ethernet: 1 port (100M)
Flashing instructions:
Upload the factory image via the vendor firmware upgrade option.
Flash instruction (TFTP):
1. Set PC to fixed ip address 192.168.0.66
2. Download *-factory.bin image and rename it to * (see below)
3. Start a tftp server with the image file in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
the firmware should be transferred from the tftp server
8. Wait ~30 second to complete recovery.
* The image name for TFTP recovery is wa901ndv4_tp_recovery.bin for
both variants.
In ar71xx, a MAC address with offset 1 was used for ethernet port.
That's probably wrong, but this commit sticks to it until we know
the correct value.
Like in ar71xx, this builds the default factory.bin with EU country
code.
Thanks to Leonardo Weiss for testing on the v5.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Increase SPI frequency to 33.333 MHz. It's maximum frequency supported
by SPI Flash memory chip without Fast read opcode.
Before:
$ time dd if=/dev/mtd1 of=/dev/null bs=8M
0+1 records in
0+1 records out
real 0m 3.21s
user 0m 0.00s
sys 0m 3.21s
After:
$ time dd if=/dev/mtd1 of=/dev/null bs=8M
0+1 records in
0+1 records out
real 0m 2.52s
user 0m 0.00s
sys 0m 2.52s
Tested on TP-Link TL-WR1043ND V2.
Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
Out of all devices currently supported based on AR9331 chipset,
this one had the 'serial0' alias missing. Add it to fix setting of
/dev/console and login shell on the onboard UART.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
This commit takes advantages of base-files 220 which introduces routines
to perform caldata loading directly via the kernel sysfs loader helper.
This has the benefits of not wasting flash space to store caldata.
Memory footprint is reduced to the bare minimum: for devices that don't
need MAC patching, the caldata is loaded directly, for devices that do
need MAC patching, the caldata is extracted to /tmp, patched and then
loaded.
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
With the implementation of a sysfs interface to access WLAN data, this
target no longer needs a special wrapper to extract caldata.
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
As evidenced here[1] the device MAC address can be stored at a random
offset in the hard_config partition. Rely on sysfs to update the MAC
address correctly.
To match sticker and vendor OS behavior, WAN MAC is set to the device
base MAC and LAN MAC is incremented from that.
Note: this will trigger a harmless kernel message during boot:
ag71xx 19000000.eth: invalid MAC address, using random address
There is no clean workaround to prevent this message from being emitted.
[1] https://github.com/openwrt/openwrt/pull/2850#issuecomment-610809021
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
This board was previously supported in ar71xx as 'RUT9XX'. The
difference between that and the other RUT955 board already supported in
ath79 is that instead of the SPI shift registers driving the LEDs and
digital outputs that model got an I2C GPIO expander instead.
To support LEDs during early boot and interrupt-driven digital inputs,
I2C support as well as support for PCA953x has to be built-in and
cannot be kernel modules, hence select those symbols for ath79/generic.
Specification:
- 550/400/200 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 4x 10/100 Mbps Ethernet, with passive PoE support on LAN1
- 2T2R 2,4 GHz (AR9344)
- built-in 4G/3G module (example: Quectel EC-25EU)
- internal microSD slot (spi-mmc, buggy and disabled for now)
- RS232 on D-Sub9 port (Cypress ACM via USB, /dev/ttyACM0)
- RS422/RS485 (AR934x high speed UART, /dev/ttyATH1)
- analog 0-24V input (MCP3221)
- various digital inputs and outputs incl. a relay
- 11x LED (4 are driven by AR9344, 7 by PCA9539)
- 2x miniSIM slot (can be swapped via GPIO)
- 2x RP-SMA/F (Wi-Fi), 3x SMA/F (2x WWAN, GPS)
- 1x button (reset)
- DC jack for main power input (9-30 V)
- debugging UART available on PCB edge connector
Serial console (/dev/ttyS0) pinout:
- RX: pin1 (square) on top side of the main PCB (AR9344 is on top)
- TX: pin1 (square) on bottom side
Flash instruction:
Vendor firmware is based on OpenWrt CC release. Use the "factory" image
directly in GUI (make sure to uncheck "keep settings") or in U-Boot web
based recovery. To avoid any problems, make sure to first update vendor
firmware to latest version - "factory" image was successfully tested on
device running "RUT9XX_R_00.06.051" firmware and U-Boot "3.0.1".
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Split device-tree of Teltonika RUT955 into a generic RUT9xx part and
a part specific to that version of RUT955 already supported.
Also harmonize GPIO and LED names with what is used by the vendor
firmware and assign RS485 DTR signal.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This adds some still-missing board names for old TP-Link devices
to ath79 SUPPORTED_DEVICES.
Fixes: FS#3017
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Like for Ubiquiti PowerBeam 5AC Gen2, the highest RSSI LED can
be exploited to indicate boot/failsafe/upgrade for the NanoBeam AC
and Nanostation AC as well.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The Ubiquiti PowerBeam 5AC Gen 2 (PBE-5AC-Gen2) is an outdoor 802.11ac
5 GHz bridge with a radio feed and a dish antenna. The device is
hardware-compatible with the LiteBeam AC Gen2, plus the 4 extra LEDs.
Specifications:
- SoC: Qualcomm Atheros AR9342 rev 2
- RAM: 64 MB DDR2
- Flash: 16 MB SPI NOR (mx25l12805d)
- Ethernet: 1x 10/100/1000 Mbps Atheros 8035, 24 Vdc PoE-in
- WiFi 5 GHz: QCA988x HW2.0 Ubiquiti target 0x4100016c chip_id 0x043222ff
- WiFi 2.4 GHz: Atheros AR9340 (SoC-based)
- Buttons: 1x (reset)
- LEDs: 1x power, 1x Ethernet, 4x RSSI via GPIO. All blue.
- UART: not tested
Installation from stock airOS firmware:
- Follow instructions for WA-type Ubiquiti devices on OpenWrt wiki
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
[changed device name in commit title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
These boards suffer from a sudden inability to establish a link on the
SGMII. Enable the workaround to fix the link when it dies.
Signed-off-by: David Bauer <mail@david-bauer.net>
ath79 does not support kernels prior to 4.19 anymore.
Remove legacy code for those kernels from the ag71xx driver.
Signed-off-by: David Bauer <mail@david-bauer.net>
This parser was added with the target, but no device seems to use it
currently, as all partitions are specified in the device-tree.
Signed-off-by: David Bauer <mail@david-bauer.net>
Some boards using a QCA9556 or QCA9558 had their machine compatible
binding incorrectly set to qca,qca9557.
Signed-off-by: David Bauer <mail@david-bauer.net>
There are at least 3 different chips in the Scorpion series of SoCs.
Rename the common DTSI to better reflect it's purpose for the whole
series.
Also rename the compatible bindings from qca,ar9557 and qca,qca9557
to qca,qca9550.
Signed-off-by: David Bauer <mail@david-bauer.net>
Between 4.19 and 5.4, mtd parsers have been moved to "parsers"
subdirectory. Like for myloader.c in the previous patch,
this patch moves tplinkpart.c to the kernel patches, so the
code and the kernel includes are at the same location and
the path can be adjusted per kernel.
While at it, remove some outdated kernel version switches from
the C code.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Between 4.19 and 5.4, mtd parsers have been moved to "parsers"
subdirectory. Based on this, the selection of myloader.o in OpenWrt
was also moved to that subdirectory, while the Kconfig and our local
myloader.c file remained in /drivers/mtd.
This resulted in linking errors like the following (on ath25@5.4):
make[8]: *** No rule to make target 'drivers/mtd/parsers/myloader.o', ...
needed by 'drivers/mtd/parsers/built-in.a'. Stop.
make[7]: *** [scripts/Makefile.build:500: drivers/mtd/parsers] Error 2
make[6]: *** [scripts/Makefile.build:500: drivers/mtd] Error 2
Since myloader.c is not too big, this patch moves it to the kernel patches,
allowing to adjust the path for kernel 5.4 and keeping Makefiles and
file paths better in sync.
Other patches have been refreshed accordingly.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
SOC: Qualcomm QCA9556 (Scorpion) 560MHz MIPS74Kc
RAM: 64MB Zentel A3R12E40CBF DDR2
FLASH: 16MiB Winbond W25Q128 SPI NOR
WLAN1: QCA9556 2.4 GHz 802.11b/g/n 3x3
INPUT: WPS button
LED: Power, WiFi, LAN, RSSI indicator
Serial: Header Next to Black metal shield
Pinout is 3.3V - RX - TX - GND (Square Pad is 3.3V)
The Serial setting is 115200-8-N-1.
Installation via EVA:
In the first seconds after Power is connected, the bootloader will
listen for FTP connections on 192.168.178.1. Firmware can be uploaded
like following:
ftp> quote USER adam2
ftp> quote PASS adam2
ftp> binary
ftp> debug
ftp> passive
ftp> quote MEDIA FLSH
ftp> put openwrt-sysupgrade.bin mtd1
Note that this procedure might take up to two minutes.
You need to powercycle the device afterwards to boot OpenWRT.
Tested-by: Andreas Ziegler <dev@andreas-ziegler.de>
Signed-off-by: David Bauer <mail@david-bauer.net>
This commit adds support for the AVM Fritz!WLAN Repeater 1750E
SOC: Qualcomm QCA9556 (Scorpion) 720MHz MIPS74Kc
RAM: 64MB Zentel A3R12E40CBF DDR2
FLASH: 16MiB Winbond W25Q128 SPI NOR
WLAN1: QCA9556 2.4 GHz 802.11b/g/n 3x3
WLAN2: QCA9880 5 GHz 802.11 n/ac 3x3
INPUT: WPS button
LED: Power, WiFi, LAN, RSSI indicator
Serial: Header Next to Black metal shield
Pinout is 3.3V - RX - TX - GND (Square Pad is 3.3V)
The Serial setting is 115200-8-N-1.
Tested and working:
- Ethernet
- 2.4 GHz WiFi (correct MAC)
- 5 GHz WiFi (correct MAC)
- Installation via EVA bootloader
- OpenWRT sysupgrade
- Buttons
- LEDs
Installation via EVA:
In the first seconds after Power is connected, the bootloader will
listen for FTP connections on 192.168.178.1. Firmware can be uploaded
like following:
ftp> quote USER adam2
ftp> quote PASS adam2
ftp> binary
ftp> debug
ftp> passive
ftp> quote MEDIA FLSH
ftp> put openwrt-sysupgrade.bin mtd1
Note that this procedure might take up to two minutes.
You need to powercycle the Device afterwards to boot OpenWRT.
Signed-off-by: David Bauer <mail@david-bauer.net>
The QCA9550 family of SoCs have a slightly different reset
sequence compared to older chips.
Normally the bootloader performs this sequence, however
some bootloader implementation expect the operating system
to clear the reset. Also get the PCIe resets from OF to
support the second RC of the QCA9558.
This is required for the AVM FRITZ!WLAN Repeater 1750E to work,
as EVA leaves the PCIe bus in reset.
Tested: AVM FRITZ!WLAN Repeater 1750E - OCEDO Koala
Signed-off-by: David Bauer <mail@david-bauer.net>
The previous spi-max-frequency value did not work with all the CPU speed
settings (configurable with rbcfg or from the stock firmware); the new
one does for the three of them.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Improve the status LED functionality in GL-AR750
by adding the definitions for different statuses
(boot, failsafe, running, flashing).
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
This adds the board name from ar71xx to support upgrade without
-F for the TP-Link TL-WA901ND v2.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This applies further fixes to the DTS of ZyXEL NBG6716 based on
what is found in ar71xx (mach-nbg6716.c):
- use WiFi label names as in ar71xx
- fix WPS gpio number
- fix GPIO_ACTIVE_HIGH and mode for WiFi switch
- add codes for USB eject buttons
- fix node name for "internet" LED
This device has separate LEDs for WAN and "Internet". As the WAN-LED
(and the four LAN-LEDs) are driven independent of the setup in
DT/01_leds, the "internet" LED is left unassigned (in contrast to
ar71xx, where it was set up effectively as a second WAN LED)
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Enables spi-mem interface usage. It speeds up flash read
in about 3x while it also workaround a possible hardware
bug when normal spi read is used.
Fixes: FS#2742
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Reimplements read optimization on top of spi-mem. Similar to
what 461-spi-ath79-add-fast-flash-read.patch used to do with
the dropped flash read interface.
It accelerate only fast-read op reading flash directly from
memory mapped region. 'm25p,fast-read' must be set in order
to use the new spi-mem.
It improved read speed up to 3x on old devices (tplink,tl-wr2543-v1)
while no speed improvement was noticed on newer devices like
(tplink,archer-c7-v2).
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
The USB LED assignment to internal ports was swapped.
Fix it.
We also explicitly checked that the LED label numbers match those
on the device.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2.4 GHz Wifi on ath79 is set up in 10-ath9k-eeprom, but in ar71xx
it was done with ath79_register_wmac.
Thus, the following errors are observed on the device:
ath: phy1: Unable to initialize hardware; initialization status: -5
ath9k 18100000.wmac: failed to initialize device
ath9k: probe of 18100000.wmac failed with error -5
This patch changes the ath79 support to properly use wmac as well.
This will also require fixing the MAC address in a different way.
Signed-off-by: Guillaume Lefebvre <guillaume@zelig.ch>
[several adjustments to 10-fix-wifi-mac, use correct MAC address,
rewrite commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Specifications:
- Qualcomm QCA9531 + QCA9886
- dual band, antenna 2*3dBi
- Output power 50mW (17dBm)
- 1x 10/100 Mbps LAN RJ45
- 128 MB RAM / 16 MB FLASH (w25q128)
- 3 LEDs (red/green/blue)
incorporated in
"color wheel reset switch"
- UART 115200 8N1
Flashing instructions:
The U-boot bootloader contains a recovery HTTP server
to upload the firmware. Push the reset button while powering the
device on and keep it pressed for ~10 seconds. The device's LEDs will
blink several times and the recovery page will be at
http://192.168.1.1; use it to upload the sysupgrade image.
Alternatively, the original firmware is based on OpenWrt so a
sysupgrade image can be installed via the stock web GUI. Settings from
the original firmware will be saved and restored on the new one, so a
factory reset will be needed. To do so, once the new firmware is flashed,
enter into failsafe mode by pressing the reset button several times during
the boot process, until it starts flashing. Once in failsafe mode, perform
a factory reset as usual.
LED-Info:
The LEDs on the Comfast stock fw have a very proprietary behaviour,
corresponding to the user selected working mode (AP, ROUTER or REPEATER).
In the first two cases, only blue is used for status and LAN signaling. When
using the latter, blue is always off (except for sysupgrade), either red
signals bad rssi on master-link, or green good. Since the default working
mode of OpenWrt resembles that of a router/AP, the default behavior is
implemented accordingly.
MAC addresses (art partition):
location address (example) use in vendor firmware
0x0 xx:xx:xx:xx:xc:f8 -> eth0
0x6 xx:xx:xx:xx:xc:fa -> wlan5g (+2)
0x1002 xx:xx:xx:xx:xc:f9 -> not used
0x5006 xx:xx:xx:xx:xc:fb -> not used
--- xx:xx:xx:xx:xd:02 -> wlan2g (+10)
The same strange situation has already been observed and documented
for COMFAST CF-E560AC.
Signed-off-by: Roman Hampel <rhamp@arcor.de>
Co-developed-by: Joao Albuquerque <joaohccalbu@gmail.com>
Signed-off-by: Joao Albuquerque <joaohccalbu@gmail.com>
[adjust and extend commit message, rebase, minor DTS adjustments,
add correct MAC address for wmac, change RSSI LED names and behavior]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
MAC addresses of the ethernet devices (eth0 & eth1) are randomly set at
boot time by the ag71xx driver, because it is currently not possible to
retrieve MAC addresses in ASCII format within the DTS file.
This commit works around this behaviour by setting the MAC addresses
during the preinit phase.
The same has been implemented recently for the Siemens WS-AP3610 in
d2b8ccb1c0 ("ath79: add support for Siemens WS-AP3610").
MAC assignment in vendor firmware is as follows:
use vendor address OpenWrt
2g wifi0 ethaddr -> wlan1
5g wifi1 ethaddr +1 -> wlan0
lan eth1 ethaddr +2 -> eth0
wan eth0 ethaddr +3 -> eth1
ethaddr is retrieved by $(mtd_get_mac_ascii u-boot-env ethaddr)
Note that both Wifi and ethernet indexing is swapped in OpenWrt
compared to vendor firmware.
Suggested-by: Guillaume Lefebvre <guillaume@zelig.ch>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Kevin Gagnon <kevin_gagnon@videotron.ca>
Specifications:
Qualcomm/Atheros QCA9531 + QCA9886
2x 10/100 Mbps Ethernet, with 48v PoE
2T2R 2.4 GHz, 802.11b/g/n
2T2R 5 GHz, 802.11a/n/ac
128MB RAM
16MB SPI Flash
4x LED (Always On Power, LAN, WAN, WLAN)
Flashing Instructions:
Original firmware is based on OpenWRT, so flashing the sysupgrade image on
the factory firmware is sufficient.
Tested: Reset button, WAN LED, LAN LED, Power LED (always on, not much
to test), WLAN LED (one LED only for 2 interfaces, by default it gets
assigned to the first interface), MAC addresses (match factory firmware).
My LAN factory MAC address ends in F2.
use stock_mac art_loc
lan :f2 0x0
wan :f3 0x1002
5g :f4 0x6
2g :f5 0x5006
Since MAC address flash locations do not really match their use in vendor
firmware (e.g. address from 5 GHz calibration data is assigned to 2.4 GHz
WiFi), just calculate the MAC addresses with an offset based on 0x0 address.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
[add MAC address comment]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This adds support for the TP-Link TL-MR3420 v3, a later revision of the
v2 with an external gpiochip similar to TP-Link Archer C7 v4.
Specifications:
SOC: Qualcomm Atheros QCA9531
CPU: 650MHz
Flash: 4 MiB
RAM: 32 MiB
WLAN: Qualcomm Atheros QCA9531 bgn 2T2R 2.4 GHz
Ethernet: 5 ports (100M)
Flashing instructions:
- Flash factory image from OEM WebUI:
openwrt-ath79-tiny-tplink_tl-mr3420-v3-squashfs-factory.bin
- Sysupgrade from ath79 image:
openwrt-ath79-tiny-tplink_tl-mr3420-v3-squashfs-sysupgrade.bin
Signed-off-by: Lim Guo Wei <limguowei@gmail.com>
[remove SUPPORTED devices, some typo adjustments, fix WAN MAC
address, fix sorting in 01_leds]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Reduce unnecessary flash wear and be tidy:
- Run the extraction only if necessary
- Extract temporary file to /tmp
- cleanup after execution
Tested-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
In RouterBOARD parlance there never was an "art" partition.
This partition has always been named 'hard_config' on ar71xx.
This partition contains more than just ART (Atheros Radio Test) data. It
includes the hardware description (product code, serial, board
identifier, name, hardware options, MAC address), as well as other bits
affecting the operation of RouterBoot.
To avoid confusion with regular ART data, this partition is renamed in
line with historical ar71xx and ramips nomenclature as 'hard_config'.
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
[minor commit title/message adjustments]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
In RouterBOARD parlance there never was an "art" partition.
This partition has always been named 'hard_config' on ar71xx.
This partition contains more than just ART (Atheros Radio Test) data. It
includes the hardware description (product code, serial, board
identifier, name, hardware options, MAC address), as well as other bits
affecting the operation of RouterBoot.
To avoid confusion with regular ART data, this partition is renamed in
line with historical ar71xx and ramips nomenclature as 'hard_config'.
This commit fixes the previous support files and implements the nested
RouterBoot partition scheme as already used by ramips-based SPI-NOR
RouterBOARD DTSes, as previously reviewed and implemented in
bbe2cf657c ("ramips: fix RBM11G partitioning").
Tested-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
[minor commit title/message adjustments]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This ports support for the TL-WA860RE v1 range extender from ar71xx
to ath79.
Specifications:
Board: AP123 / AR9341 rev. 3
Flash/RAM: 4/32 MiB
CPU: 535 MHz
WiFi: 2.4 GHz b/g/n
Ethernet: 1 port (100M)
Two external antennas
Flashing instructions:
Upload the factory image via the vendor firmware upgrade option.
Recovery:
Note that this device does not provide TFTP via ethernet like many
other TP-Link devices do. You will have to open the case if you
require recovery beyond failsafe.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Sebastian Knapp <sebastian4842@outlook.com>
This device seems to be identical to the TL-WDR4300, just with
different release date/region and TPLINK_HWID.
Support is added based on the ar71xx implementation.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The reset assert and deassert methods currently miss
a return value, leading to a compilation warning.
Return the return-value of reset_control_assert and
reset_control_deassert to fix these warnings.
Suggested-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
Signed-off-by: David Bauer <mail@david-bauer.net>
This fixes the compilation of the AR934x NAND controller
driver for kernel 5.4 while leaving it untouched for
kernel 4.19.
This change is currently not run-tested, as i do not have such
a device at hand.
CC: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
CC: André Valentin <avalentin@marcant.net>
CC: WeiDong Jia <jwdsccd@gmail.com>
Signed-off-by: David Bauer <mail@david-bauer.net>
Tested-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
The Uniquiti AC Pro and Ubiquiti AC Mesh Pro currently have the
"Primary" and "Secondary" ethernet ports configured to offer LAN as well
as WAN. However, Uiquiti describes the following behavior for the
devices Ethernet ports:
> Secondary UniFi Access Point (UAP) Ethernet ports don't
> provide PoE passthrough (to run current to a second powered
> device), but they do support data passthrough.
> It serves as a bridged interface between main / secondary
> Ethernet port.
To reduce confusion for users (as LAN and WAN functionality is not
visible on the device itself), configure both ports to offer LAN
functionality. Users can still configure a WAN interface on a port they
are able to choose.
CC: Lucian Cristian <lucian.cristian@gmail.com>
Reported-by: Florian Klink <flokli@flokli.de>
Signed-off-by: David Bauer <mail@david-bauer.net>
This patch adds support for the Ubiquiti NanoBridge M (XM), a
802.11n wireless with a feed+dish form factor, with the same board
definition as the Bullet M (XM).
Specifications:
- Atheros AR7241 SoC
- 32 MB RAM
- 8 MB SPI flash
- 1x 10/100 Mbps Ethernet port, 24 Vdc PoE-in
- Power and LAN green LEDs
- 4x RSSI LEDs (red, orange, green, green)
- UART (115200 8N1)
Flashing via stock GUI:
- WARNING: flashing OpenWrt from AirOS v5.6 or newer will brick your
device! Read the wiki for more info.
- Downgrade to AirOS v5.5.x (latest available is 5.5.11) first.
- Upload the factory image via AirOS web GUI.
Flashing via TFTP:
- WARNING: flashing OpenWrt from AirOS v5.6 or newer will brick your
device! Read the wiki for more info.
- Downgrade to AirOS v5.5.x (latest available is 5.5.11) first.
- Use a pointy tool (e.g., pen cap, slotted screwdriver) to keep the
reset button pressed.
- Power on the device (keep reset button pressed).
- Keep pressing until LEDs flash alternatively LED1+LED3 =>
LED2+LED4 => LED1+LED3, etc.
- Release reset button.
- The device starts a TFTP server at 192.168.1.20.
- Set a static IP on the computer (e.g., 192.168.1.21/24).
- Upload via tftp the factory image:
$ tftp 192.168.1.20
tftp> bin
tftp> trace
tftp> put openwrt-ath79-generic-xxxxx-ubnt_nanobridge-m-squashfs-factory.bin
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
[rebase, fix includes in DTS, add label MAC address, add SOC and
fix sorting in generic-ubnt.mk]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Now that check-size uses IMAGE_SIZE by default, we can skip the argument from
image recipes to reduce redundancy.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[do not touch ar71xx]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Place DEVICE_VARS assignments at the top of the file or above Device/Default
to make them easier to find.
For ramips, remove redundant values already present in parent file.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[do not touch ar71xx, extend commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This adds support for the Ubiquiti Bullet M (AR7240).
Specifications:
- AR7240 SoC @ 400 MHz
- 32 MB RAM
- 8 MB SPI flash
- 1x 10/100 Mbps Ethernet, 24 Vdc PoE-in
- External antenna
- POWER/LAN green LEDs
- 4x RSSI LEDs (red, orange, green, green)
- UART (115200 8N1) on PCB
Flashing via WebUI:
Upload the factory image via the stock firmware web UI.
Attention: airOS firmware versions >= 5.6 have a new bootloader with
an incompatible partition table!
Please downgrade to <= 5.5 _before_ flashing OpenWrt!
Refer to the device's Wiki page for further information.
Flashing via TFTP:
Same procedure as other Ubiquiti M boards.
- Use a pointy tool (e.g., pen cap, paper clip) and keep the reset
button on the device or on the PoE supply pressed
- Power on the device via PoE (keep reset button pressed)
- Keep pressing until LEDs flash alternatively LED1+LED3 =>
LED2+LED4 => LED1+LED3, etc.
- Release reset button
- The device starts a TFTP server at 192.168.1.20
- Set a static IP on the computer (e.g., 192.168.1.21/24)
- Upload via tftp the factory image:
$ tftp 192.168.1.20
tftp> bin
tftp> trace
tftp> put openwrt-ath79-generic-xxxxx-ubnt_bullet-m-ar7240-squashfs-factory.bin
The "fixed-link" section of the device tree is needed to avoid errors like this:
Generic PHY mdio.0:1f:04: Master/Slave resolution failed, maybe conflicting manual settings?
With "fixed-link", the errors go away and eth0 comes up reliably.
Signed-off-by: Russell Senior <russell@personaltelco.net>
[fix SUPPORTED_DEVICES]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
TP-Link Archer D7 v1 is a dual-band AC1750 router + modem.
The router section is based on Qualcomm/Atheros QCA9558 + QCA9880.
The "DSL" section is based on BCM6318 but it's currently not supported.
The Archer D7b seems to differ from the Archer D7 only in the
partition table.
Router section - Specification:
775/650/258 MHz (CPU/DDR/AHB)
128 MB of RAM (DDR2)
16 MB of FLASH (SPI NOR)
3T3R 2.4 GHz
3T3R 5 GHz
4x 10/100/1000 Mbps Ethernet
7x LED, 2x button
UART header on PCB
Known issues:
- Broadband LED (missing GPIO - probably driven by the BCM6318)
- Internet LED (missing GPIO - probably driven by the BCM6318)
- WIFI LED (working only for one interface at a time, while in the
OEM firmware works for both wifi interfaces; thus, this patch does
not set a trigger by default)
- DSL not working (eth0)
UART connection
---------------
J1 HEADER (Qualcomm CPU)
. VCC
. GND
. RX
O TX
J41 HEADER (Broadcom CPU)
. VCC
. GND
. RX
O TX
The following instructions require a connection to the J1 UART header
and are tested for the Archer D7 v1.
For the Archer D7b v1, names should be changed accordingly.
Flash instructions under U-Boot, using UART
------------------------------------------
1. Press "tpl" to stop autobooting and obtain U-Boot CLI access.
2. Setup ip addresses for U-Boot and your tftp server.
3. Issue below commands:
tftpboot 0x81000000 openwrt-ath79-generic-tplink_archer-d7-v1-squashfs-sysupgrade.bin
erase 0x9f020000 +f90000
cp.b 0x81000000 0x9f020000 0xf90000
reset
Initramfs instructions under U-Boot for testing, using UART
----------------------------------------------------------
1. Press "tpl" to stop autobooting and obtain U-Boot CLI access.
2. Setup ip addresses for U-Boot and your tftp server.
3. Issue below commands:
tftpboot 0x81000000 openwrt-ath79-generic-tplink_archer-d7-v1-initramfs-kernel.bin
bootm 0x81000000
4. Here you can backup the original firmware and/or flash the sysupgrade openwrt if you want
Restore the original firmware
-----------------------------
0. Backup every partition using the OpenWrt web interface
1. Download the OEM firmware from the TP-Link website
2. Extract the bin file in a folder (eg. Archer_D7v1_1.6.0_0.9.1_up_boot(160216)_2016-02-16_15.55.48.bin)
3. Remove the U-Boot and the Broadcom image part from the file.
Issue the following command:
dd if="Archer_D7v1_1.6.0_0.9.1_up_boot(160216)_2016-02-16_15.55.48.bin" of="Archer_D7v1_1.6.0_0.9.1_up_boot(160216)_2016-02-16_15.55.48.bin.mod" skip=257 bs=512 count=31872
4. Double check the .mod file size. It must be 16318464 bytes.
5. Flash it using the OpenWrt web interface. Force the update if needed.
WARNING: Remember to NOT keep settings.
5b. (Alternative to 5.) Flash it using the U-Boot and UART connection.
Issue below commands in the U-Boot:
tftpboot 0x81000000 Archer_D7v1_1.6.0_0.9.1_up_boot(160216)_2016-02-16_15.55.48.bin.mod
erase 0x9f020000 +f90000
cp.b 0x81000000 0x9f020000 0xf90000
reset
Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
[cosmetic DTS changes, remove TPLINK_HWREVADD := 0, do not use two
phyXtpt at once, add missing buttons, minor commit message adjustments]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
TP-Link Archer C60 v3 is a dual-band AC1350 router,
based on Qualcomm/Atheros QCA9561 + QCA9886.
It seems to be identical to the v2 revision, except that
it lacks a WPS LED and has different GPIO for amber WAN LED.
Specification:
- 775/650/258 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 2T2R 5 GHz
- 5x 10/100 Mbps Ethernet
- 6x LED, 2x button
- UART header on PCB
Flash instruction (WebUI):
Download *-factory.bin image and upload it via the firmwary upgrade
function of the stock firmware WebUI.
Flash instruction (TFTP):
1. Set PC to fixed IP address 192.168.0.66
2. Download *-factory.bin image and rename it to tp_recovery.bin
3. Start a tftp server with the file tp_recovery.bin in its root
directory
4. Turn off the router
5. Press and hold reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time the firmware should
be transferred from the tftp server
8. Wait ~30 second to complete recovery
While TFTP works for OpenWrt images, my device didn't accept the
only available official firmware "Archer C60(EU)_V3.0_190115.bin".
In contrast to earlier revisions (v2), the v3 contains the (same)
MAC address twice, once in 0x1fa08 and again in 0x1fb08.
While the partition-table on the device refers to the latter, the
firmware image contains a different partition-table for that region:
name device firmware
factory-boot 0x00000-0x1fb00 0x00000-0x1fa00
default-mac 0x1fb00-0x1fd00 0x1fa00-0x1fc00
pin 0x1fd00-0x1fe00 0x1fc00-0x1fd00
product-info 0x1fe00-0x1ff00 0x1fd00-0x1ff00
device-id 0x1ff00-0x20000 0x1ff00-0x20000
While the MAC address is present twice, other data like the PIN isn't,
so with the partitioning from the firmware image the PIN on the device
would actually be outside of its partition.
Consequently, the patch uses the MAC location from the device (which
is the same as for the v2).
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Since there exists another variant of the Bullet M with AR7240 SoC
under the same name, this patch introduces the SoC into the device
name to be able to distinguish these variants.
Signed-off-by: Russell Senior <russell@personaltelco.net>
[add commit message, adjust model in DTS, fix 02_network and
SUPPORTED_DEVICES]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* Prepare to support the AR7240 variant of ubiquiti bullet m, by
reorganizing the related dtsi files.
* Distribute SOC variable across ubnt-xm devices.
Signed-off-by: Russell Senior <russell@personaltelco.net>
When creating the mikrotik subtarget, the execute bit on 02_network
was not set. Fix it.
Fixes: a66eee6336 ("ath79: add mikrotik subtarget")
Reported-by: Christopher Hill <ch6574@gmail.com>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
So far, specifying "BOARD_NAME := routerboard" is required by the
upgrade code of Mikrotik NAND devices, as "sysupgrade-routerboard"
is hardcoded in platform_do_upgrade_mikrotik_nand().
This patch replaces the latter with a grep for the name like it
is already done in nand_upgrade_tar() in /lib/upgrade/nand.sh.
By that, BOARD_NAME is obsolete now for this device.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>