openwrt/target/linux/ath79
Davy Hollevoet 394f54ee62 ath79/nand: add support for Netgear WNDR4300TN
This patch adds support for the WNDR4300TN, marketed by Belgian ISP
Telenet. The hardware is the same as the WNDR4300 v1, without the
fifth ethernet port (WAN) and the USB port. The circuit board has
the traces, but the components are missing.

Specifications:
* SoC: Atheros AR9344
* RAM: 128 MB
* Flash: 128 MB NAND flash
* WiFi: Atheros AR9580 (5 GHz) and AR9344 (2.4 GHz)
* Ethernet: 4x 1000Base-T
* LED: Power, LAN, WiFi 2.4GHz, WiFi 5GHz, WPS
* UART: on board, to the right of the RF shield at the top of the board

Installation:

* Flashing through the OEM web interface:
  + Connect your computer to the router with an ethernet cable and browse
    to http://192.168.0.51/
  + Log in with the default credentials are admin:password
  + Browse to Advanced > Administration > Firmware Upgrade in the Telenet
    interface
  + Upload the Openwrt firmware: openwrt-ath79-nand-netgear_wndr4300tn-squashfs-factory.img
  + Proceed with the firmware installation and give the device a few
    minutes to finish and reboot.

* Flashing through TFTP:
  + Configure your wired client with a static IP in the 192.168.1.x range,
    e.g. 192.168.1.10 and netmask 255.255.255.0.
  + Power off the router.
  + Press and hold the RESET button (the factory reset button on the bottom
    of the device, with the gray circle around it, next to the Telenet logo)
    and turn the router on while keeping the button pressed.
  + The power LED will start flashing orange. You can release the button
    once it switches to flashing green.
  + Transfer the image over TFTP:
    $ tftp 192.168.1.1 -m binary -c put openwrt-ath79-nand-netgear_wndr4300tn-squashfs-factory.img

Signed-off-by: Davy Hollevoet <github@natox.be>
[use DT label reference for adding LEDs in DTSI files]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-06 16:56:07 +02:00
..
base-files/etc/hotplug.d/ieee80211 ath79: add mikrotik subtarget 2020-03-17 11:50:47 +01:00
dts ath79/nand: add support for Netgear WNDR4300TN 2020-08-06 16:56:07 +02:00
files kernel: Update kernel 4.19 to version 4.19.131 2020-07-04 21:12:42 +02:00
generic ath79: add support for Compex WPJ563 2020-07-26 02:14:45 +02:00
image ath79/nand: add support for Netgear WNDR4300TN 2020-08-06 16:56:07 +02:00
mikrotik ath79: mikrotik: use base mac on lan for RBwAPG-5HacT2HnD 2020-07-25 22:01:34 +02:00
nand ath79/nand: add support for Netgear WNDR4300TN 2020-08-06 16:56:07 +02:00
patches-4.19 ath79: add support for Arduino Yun 2020-07-08 23:22:30 +02:00
patches-5.4 ath79: add support for Arduino Yun 2020-07-08 23:22:30 +02:00
tiny ath79: add support for TP-Link TL-WA801ND v3/v4 2020-06-19 15:50:29 +02:00
config-4.19 kernel: unify CONFIG_GPIO_SYSFS in kernel configs 2020-08-06 12:37:04 +02:00
config-5.4 kernel: unify CONFIG_GPIO_SYSFS in kernel configs 2020-08-06 12:37:04 +02:00
Makefile ath79: switch to kernel 5.4 2020-07-07 10:33:17 +02:00
modules.mk ath79: add new OF only target for QCA MIPS silicon 2018-05-07 08:06:51 +02:00