Specifications:
- SoC: MediaTek MT7621AT
- RAM: 128 MB (DDR3)
- Flash: 16 MB (SPI NOR)
- WiFi: MediaTek MT7603E, MediaTek MT7612E
- Switch: 1 WAN, 4 LAN (Gigabit)
- Ports: 1 USB 3.0
- Buttons: Reset, WPS
- LEDs: Power, System, Wan, Lan 1-4, WiFi 2.4G, WiFi 5G, WPS, USB
- Power: DC 12V 1A tip positive
UART Serial:
115200 baud
Located on unpopulated 4 pin header near J4:
J4
[o] Rx
[o] Tx
[o] GND
[ ] Vcc - Do not connect
Installation:
Download and flash the manufacturer's built OpenWRT image available at
http://www.cudytech.com/openwrt_software_download
Install the new OpenWRT image via luci (System -> Backup/Flash firmware)
Be sure to NOT keep settings. The force upgrade may need to be checked
due to differences in router naming conventions.
Recovery:
- Loads only signed manufacture firmware due to bootloader RSA verification
- serve tftp-recovery image as /recovery.bin on 192.168.1.88/24
- connect to any lan ethernet port
- power on the device while holding the reset button
- wait at least 8 seconds before releasing reset button for image to
download
- See http://www.cudytech.com/newsinfo/547425.html
MAC addresses as verified by OEM firmware:
use address source
LAN *:f0 label
WAN *:f1 label + 1
2g *:f0 label
5g *:f2 label + 2
The label MAC address is found in bdinfo 0xde00.
Signed-off-by: Andrew Pikler <andrew.pikler@gmail.com>
While the latest version of 19.07 release is usable,
the current master is unbootable on the device in a normal way.
"Normal way" installations includes:
- sysupgrade (e.g. from 19.07)
- RESET button recovery with Ron Curry's (Wingspinner) UBoot image
(10.10.10.3 + "Kernal.bin")
- RESET button recovery with original U-Boot
(10.10.10.254 + "kernel")
One could flash and boot the latest master sysupgrade image successfully
with serial access to the device. But a sysupgrade from this state still
breaks the U-Boot and soft-bricks the device.
Signed-off-by: Szabolcs Hubai <szab.hu@gmail.com>
UniElec U7621-01 is a router platform board, the smaller model of
the U7621-06.
The device has the following specifications:
- MT7621AT (880 MHz)
- 256 of RAM (DDR3)
- 16 MB of FLASH (SPI NOR)
- 5x 1 Gbps Ethernet (MT7621 built-in switch)
- 1x 2.4Ghz MT7603E
- 1x 5Ghz MT7612
- 1x miniPCIe slots (PCIe bus only)
- 1x miniSIM slot
- 1x USB 2.0 (uses the usb 3.0 driver)
- 8x LEDs (1x GPIO-controlled)
- 1x reset button
- 1x UART header (4-pins)
- 1x GPIO header (30-pins)
- 1x DC jack for main power (12 V)
The following has been tested and is working:
- Ethernet switch
- 1x 2.4Ghz MT7603E (wifi)
- 1x 5Ghz MT7612 (wifi)
- miniPCIe slots (tested with Wi-Fi cards and LTE modem cards)
- miniSIM slot (works with normal size simcard)
- sysupgrade
- reset button
Installation:
This board has no locked down bootloader. The seller can be asked to
install openwrt v18.06, so upgrades are standard sysupgrade method.
Recovery:
This board contains a Chinese, closed-source bootloader called Breed
(Boot and Recovery Environment for Embedded Devices). Breed supports web
recovery and to enter it, you keep the reset button pressed for around
5 seconds during boot. Your machine will be assigned an IP through DHCP
and the router will use IP address 192.168.1.1. The recovery website is
in Chinese, but is easy to use. Click on the second item in the list to
access the recovery page, then the second item on the next page is where
you select the firmware. In order to start the recovery, you click the
button at the bottom.
LEDs list (left to right):
- ESW_P0_LED_0
- ESW_P1_LED_0
- ESW_P2_LED_0
- ESW_P3_LED_0
- ESW_P4_LED_0
- CTS2_N (GPIO10, configured as "status" LED)
- LED_WLAN# (connected with pin 44 in wifi1 slot)
Signed-off-by: David Bentham <db260179@gmail.com>
[add DEVICE_VARIANT, fix DEVICE_PACKAGES, remove &gpio]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Specifications:
- SoC: MediaTek MT7688AN
- RAM: 128 MB
- Flash: 32 MB
- Ethernet: 5x 10/100 (1x WAN, 4x LAN)
- Wireless: built in 2.4GHz (bgn)
- USB: 1x USB 2.0 port
- Buttons: 1x Reset
- LEDs: 1x (WiFi)
Flash instructions:
- Configure TFTP server with IP address 10.10.10.3
- Name the firmware file as firmware.bin
- Connect any Ethernet port to the TFTP server's LAN
- Choose option 2 in U-Boot
- Alternatively choose option 7 to upload firmware to the built-in
web server
MAC addresses as verified by OEM firmware:
use address source
2g *:XX factory 0x4
LAN *:XX+1 factory 0x28
WAN *:XX+1 factory 0x2e
Notes:
This board is ostensibly a module containing the MediaTek MT7688AN SoC,
128 MB DDR2 SDRAM and 32 MB flash storage. The SoC can be operated in
IoT Gateway Mode or IoT Device Mode.
From some vendors the U-Boot that comes installed operates on UART 2
which is inaccessible in gateway mode and operates unreliably in the
Linux kernel when using more than 64 MB of RAM. For those, updating
U-Boot is recommended.
Signed-off-by: Ewan Parker <ewan@ewan.cc>
[add WLAN to 01_leds]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The majority of our targets provide a default value for the variable
SUPPORTED_DEVICES, which is used in images to check against the
compatible on a running device:
SUPPORTED_DEVICES := $(subst _,$(comma),$(1))
At the moment, this is implemented in the Device/Default block of
the individual targets or even subtargets. However, since we
standardized device names and compatible in the recent past, almost
all targets are following the same scheme now:
device/image name: vendor_model
compatible: vendor,model
The equal redundant definitions are a symptom of this process.
Consequently, this patch moves the definition to image.mk making it
a global default. For the few targets not using the scheme above,
SUPPORTED_DEVICES will be defined to a different value in
Device/Default anyway, overwriting the default. In other words:
This change is supposed to be cosmetic.
This can be used as a global measure to get the current compatible
with: $(firstword $(SUPPORTED_DEVICES))
(Though this is not precisely an achievement of this commit.)
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Xiaomi Mi Router 4 is the same as Xiaomi Mi Router 3G, except for
the RAM (256Mib→128Mib), LEDs and gpio (MiNet button).
Specifications:
Power: 12 VDC, 1 A
Connector type: barrel
CPU1: MediaTek MT7621A (880 MHz, 4 cores)
FLA1: 128 MiB (ESMT F59L1G81MA)
RAM1: 128 MiB (ESMT M15T1G1664A)
WI1 chip1: MediaTek MT7603EN
WI1 802dot11 protocols: bgn
WI1 MIMO config: 2x2:2
WI1 antenna connector: U.FL
WI2 chip1: MediaTek MT7612EN
WI2 802dot11 protocols: an+ac
WI2 MIMO config: 2x2:2
WI2 antenna connector: U.FL
ETH chip1: MediaTek MT7621A
Switch: MediaTek MT7621A
UART Serial
[o] TX
[o] GND
[o] RX
[ ] VCC - Do not connect it
MAC addresses as verified by OEM firmware:
use address source
LAN *:c2 factory 0xe000 (label)
WAN *:c3 factory 0xe006
2g *:c4 factory 0x0000
5g *:c5 factory 0x8000
Flashing instructions:
1.Create a simple http server (nginx etc)
2.set uart enable
To enable writing to the console, you must reset to factory settings
Then you see uboot boot, press the keyboard 4 button (enter uboot command line)
If it is not successful, repeat the above operation of restoring the factory settings.
After entering the uboot command line, type:
setenv uart_en 1
saveenv
boot
3.use shell in uart
cd /tmp
wget http://"your_computer_ip:80"/openwrt-ramips-mt7621-xiaomi_mir4-squashfs-kernel1.bin
wget http://"your_computer_ip:80"/openwrt-ramips-mt7621-xiaomi_mir4-squashfs-rootfs0.bin
mtd write openwrt-ramips-mt7621-xiaomi_mir4-squashfs-kernel1.bin kernel1
mtd write openwrt-ramips-mt7621-xiaomi_mir4-squashfs-rootfs0.bin rootfs0
nvram set flag_try_sys1_failed=1
nvram commit
reboot
4.login to the router http://192.168.1.1/
Installation via Software exploit
Find the instructions in the https://github.com/acecilia/OpenWRTInvasion
Signed-off-by: Dmytro Oz <sequentiality@gmail.com>
[commit message facelift, rebase onto shared DTSI/common device
definition, bump uboot-envtools]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This creates a shared device definition for Xiaomi devices with
NAND and "separate" images, i.e. kernel1.bin and rootfs0.bin.
This allows to consolidate similar/duplicate code for AC2100 family
and Mi Router 3G.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The following four led triggers are enabled in generic config.
* kmod-ledtrig-default-on
* kmod-ledtrig-heartbeat
* kmod-ledtrig-netdev
* kmod-ledtrig-timer
Drop the packages and remove them from DEVICE_PACKAGES.
There's no other package depending on them in this repo.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Remove trailing whitespaces in two *.mk files.
Signed-off-by: Leon M. George <leon@georgemail.eu>
[fix title, add message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Hardware
--------
MediaTek MT7621AT
256M DDR3
32M SPI-NOR
MediaTek MT7603 2T2R 802.11n 2.4GHz
MediaTek MT7915 2T2R 802.11ax 5GHz
Not Working
-----------
- Bluetooth (connected to UART3)
UART
----
UART is located in the lower left corner of the board. Pinout is
0 - 3V3 (don't connect)
1 - RX
2 - TX
3 - GND
Console is 115200 8N1.
Boot
----
1. Connect to the serial console and connect power.
2. Double-press ESC when prompted
3. Set the fdt address
$ fdt addr $(fdtcontroladdr)
4. Remove the signature node from the control FDT
$ fdt rm /signature
5. Transfer and boot the OpenWrt initramfs image to the device.
Make sure to name the file C0A80114.img and have it reachable at
192.168.1.1/24
$ tftpboot; bootm
Installation
------------
1. Connect to the booted device at 192.168.1.20 using username/password
"ubnt".
2. Update the bootloader environment.
$ fw_setenv devmode TRUE
$ fw_setenv boot_openwrt "fdt addr \$(fdtcontroladdr);
fdt rm /signature; bootubnt"
$ fw_setenv bootcmd "run boot_openwrt"
3. Transfer the OpenWrt sysupgrade image to the device using SCP.
4. Check the mtd partition number for bs / kernel0 / kernel1
$ cat /proc/mtd
5. Set the bootselect flag to boot from kernel0
$ dd if=/dev/zero bs=1 count=1 of=/dev/mtdblock4
6. Write the OpenWrt sysupgrade image to both kernel0 as well as kernel1
$ dd if=openwrt.bin of=/dev/mtdblock6
$ dd if=openwrt.bin of=/dev/mtdblock7
7. Reboot the device. It should boot into OpenWrt.
Below are the original installation instructions prior to the discovery
of "devmode=TRUE". They are not required for installation and are
documentation only.
The bootloader employs signature verification on the FIT image
configurations. This way, booting unauthorized image without patching
the bootloader is not possible. Manually configuring the bootcmd in the
U-Boot envronment won't work, as this is restored to the default value
if modified.
The bootloader is made up of three different parts.
1. The SPL performing early board initialization and providing a XModem
recovery in case the PBL is missing
2. The PBL being the primary U-Boot application and containing the
control FDT. It is LZMA packed with a uImage header.
3. A Ubiquiti standalone U-Boot application providing the main boot
routine as well as their recovery mechanism.
In a perfect world, we would only replace the PBL, as the SPL does not
perform checks on the PBLs integrity. However, as the PBL is in the same
eraseblock as the SPL, we need to at least rewrite both.
The bootloader will only verify integrity in case it has a "signature"
node in it's control device-tree. Renaming the signature node to
something else will prevent this from happening.
Warning: These instructions are based on the firmware intially
shipped with the device and potentially brick your device in a way it
can only be recovered using a SPI flasher.
Only (!) proceed if you understand this!
1. Extract the bootloader from the U-Boot partition using the OpenWrt
initramfs image.
2. Split the bootloader into it's 3 components:
$ dd if=bootloader.bin of=spl.bin bs=1 skip=0 count=45056
$ dd if=bootloader.bin of=pbl.uimage bs=1 skip=45056 count=143360
$ dd if=bootloader.bin of=ubnt.uimage bs=1 skip=188416
3. Strip the uImage header from the PBL
$ dd if=pbl.uimage of=pbl.lzma bs=64 skip=1
4. Decompress the PBL
$ lzma -d pbl.lzma --single-stream
The decompressed PBL sha256sum should be
d8b406c65240d260cf15be5f97f40c1d6d1b6e61ec3abed37bb841c90fcc1235
5. Open the decompressed PBL using your favorite hexeditor. Locate the
control FDT at offset 0x4CED0 (0xD00DFEED). At offset 0x4D5BC, the
label for the signature node is located. Rename the "signature"
string at this offset to "signaturr".
The patched PBL sha256sum should be
d028e374cdb40ba44b6e3cef2e4e8a8c16a3b85eb15d9544d24fdd10eed64c97
6. Compress the patched PBL
$ lzma -z pbl --lzma1=dict=67108864
The resulting pbl.lzma file should have the sha256sum
7ae6118928fa0d0b3fe4ff81abd80ecfd9ba2944cb0f0a462b6ae65913088b42
7. Create the PBL uimage
$ SOURCE_DATE_EPOCH=1607909492 mkimage -A mips -O u-boot -C lzma
-n "U-Boot 2018.03 [UniFi,v1.1.40.71]" -a 84000000 -e 84000000
-T firmware -d pbl.lzma patched_pbl.uimage
The resulting patched_pbl.uimage should have the sha256sum
b90d7fa2dcc6814180d3943530d8d6b0d6a03636113c94e99af34f196d3cf2ce
8. Reassemble the complete bootloader
$ dd if=patched_pbl.uimage of=aligned_pbl.uimage bs=143360 count=1
conv=sync
$ cat spl.bin > patched_uboot.bin
$ cat aligned_pbl.uimage >> patched_uboot.bin
$ cat ubnt.uimage >> patched_uboot.bin
The resulting patched_uboot.bin should have the sha256sum
3e1186f33b88a525687285c2a8b22e8786787b31d4648b8eee66c672222aa76b
9. Transfer your patched bootloader to the device. Also install the
kmod-mtd-rw package using opkg and load it.
$ insmod mtd-rw.ko i_want_a_brick=1
Write the patched bootloader to mtd0
$ mtd write patched_uboot.bin u-boot
10. Erase the kernel1 partition, as the bootloader might otherwise
decide to boot from there.
$ mtd erase kernel1
11. Transfer the OpenWrt sysupgrade image to the device and install
using sysupgrade.
FIT configurations
------------------
In the future, the MT7621 UniFi6 family can be supported by a single
OpenWrt image.
config@1: U6 Lite
config@2: U6 IW
config@3: U6 Mesh
config@4: U6 Extender
config@5: U6 LR-EA (Early Access - GA is MT7622)
Signed-off-by: David Bauer <mail@david-bauer.net>
ELECOM WRC-1167GST2 is a 2.4/5 GHz band 11ac (Wi-Fi 5) router, based
on MT7621A.
Specification:
- SoC : MediaTek MT7621A
- RAM : DDR3 256 MiB
- Flash : SPI-NOR 32 MiB
- WLAN : 2.4/5 GHz 2T2R (MediaTek MT7615D)
- Ethernet : 10/100/1000 Mbps x5
- Switch : MediaTek MT7530 (SoC)
- LED/keys : 6x/6x (2x buttons, 1x slide-switch)
- UART : through-hole on PCB
- J4: 3.3V, GND, TX, RX from ethernet port side
- 57600n8
- Power : 12VDC, 1A
MAC addresses:
LAN : 04:AB:18:**:**:07 (Factory, 0xE000 (hex))
WAN : 04:AB:18:**:**:08 (Factory, 0xE006 (hex))
2.4 GHz : 04:AB:18:**:**:09 (none)
5 GHz : 04:AB:18:**:**:0A (none)
Flash instruction using factory image:
1. Boot WRC-1167GST2 normally
2. Access to "http://192.168.2.1/" and open firmware update page
("ファームウェア更新")
3. Select the OpenWrt factory image and click apply ("適用") button
4. Wait ~150 seconds to complete flashing
Notes:
- there is no way to configure the correct MAC address for secondary phy
(5GHz) on MT7615D
- Wi-Fi band on primary phy (2.4GHz) cannot be limitted by specifying
ieee80211-freq-limit
(fail to register secondary phy due to error)
- mtd-mac-address in the wifi node is required for using
mtd-mac-address-increment
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
[rebase onto split DTSI]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
ELECOM WRC-1167GS2-B is a 2.4/5 GHz band 11ac (Wi-Fi 5) router, based
on MT7621A.
Specification:
- SoC : MediaTek MT7621A
- RAM : DDR3 128 MiB
- Flash : SPI-NOR 16 MiB
- WLAN : 2.4/5 GHz 2T2R (MediaTek MT7615D)
- Ethernet : 10/100/1000 Mbps x5
- Switch : MediaTek MT7530 (SoC)
- LED/keys : 6x/6x (2x buttons, 1x slide-switch)
- UART : through-hole on PCB
- J4: 3.3V, GND, TX, RX from ethernet port side
- 57600n8
- Power : 12VDC, 1A
MAC addresses:
LAN : 04:AB:18:**:**:13 (Factory, 0xFFF4 (hex))
WAN : 04:AB:18:**:**:14 (Factory, 0xFFFA (hex))
2.4 GHz : 04:AB:18:**:**:15 (none)
5 GHz : 04:AB:18:**:**:16 (Factory, 0x4 (hex))
Flash instruction using factory image:
1. Boot WRC-1167GS2-B normally
2. Access to "http://192.168.2.1/" and open firmware update page
("ファームウェア更新")
3. Select the OpenWrt factory image and click apply ("適用") button
4. Wait ~120 seconds to complete flashing
Notes:
- there is no way to configure the correct MAC address for secondary phy
(5GHz) on MT7615D
- Wi-Fi band on primary phy (2.4GHz) cannot be limitted by specifying
ieee80211-freq-limit
(fail to register secondary phy due to error)
- mtd-mac-address in the wifi node is required for using
mtd-mac-address-increment
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
[rebase onto split DTSI patch]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Specifications:
- SoC: MediaTek MT7621AT
- RAM: 128 MB (DDR3)
- Flash: 16 MB (SPI NOR)
- WiFi: MediaTek MT7615N (x2)
- Switch: 1 WAN, 4 LAN (Gigabit)
- Ports: 1 USB 2.0, 1 USB 3.0
- Buttons: Reset, WiFi Toggle, WPS
- LEDs: Power, Internet, WiFi 2.4G WiFi 5G, USB 2.0, USB 3.0
The R1 revision is identical to the A1 revision except
- No Config2 Parition, therefore
- factory partition resized to 64k from 128K
- Firmware partition offset is 0x50000 not 0x60000
- Firmware partitions size increased by 64K
- Firmware partition type is "denx,uimage", not "sge,uimage"
- Padding of image creation "uimage-padhdr 96" removed
Installation:
- Older firmware versions: put the factory image on a USB stick, turn on
the telnet console, and flash using the following cmd
"fw_updater Linux /mnt/usb_X_X/firmware.bin"
- D-Link FailsafeUI:
Power down the router, press and hold the reset button, then
re-plug it. Keep the reset button pressed until the internet LED stops
flashing, then jack into any lan port and manually assign a static IP
address in 192.168.0.0/24 other than 192.168.0.0 (e.g. 192.168.0.2)
and go to http://192.168.0.1
Flash with the factory image.
Signed-off-by: Andrew Pikler <andrew.pikler@gmail.com>
Some Russian d-link routers require that their firmware be signed with a
salted md5 checksum followed by the bytes 0x00 0xc0 0xff 0xee. This tool
signs factory images the OEM's firmware accepts them.
Signed-off-by: Andrew Pikler <andrew.pikler@gmail.com>
FCC ID: A8J-ESR750H
Engenius ESR600H is an indoor wireless router with a gigabit switch,
2.4 GHz and 5 GHz wireless, internal and external antennas, and a USB port.
**Specification:**
- RT3662F MIPS SOC, 5 GHz WMAC (2x2)
- RT5392L PCI on-board, 2.4 GHz (2x2)
- AR8327 RGMII, 7-port GbE, 25 MHz clock
- 40 MHz reference clock
- 8 MB FLASH 25L6406EM2I-12G
- 64 MB RAM
- UART at J12 (unpopulated)
- 2 internal antennas (5 GHz)
- 2 external antennas (2.4 GHz)
- 9 LEDs, 1 button (power, wps, wifi2g, wifi5g, 5 LAN/WAN)
- USB 2 port (GPIO controlled power)
**MAC addresses:**
MAC Addresses are labeled as WAN and WLAN
U-boot environment has the the vendor MAC address for ethernet
MAC addresses in "factory" are part of wifi calibration data
eth0.2 WAN *:13:e7 u-boot-env wanaddr
eth0.1 ---- *:13:e8 u-boot-env wanaddr + 1
phy0 WLAN *:14:b8 factory 0x8004
phy1 ---- *:14:bc factory 0x4
**Installation:**
Method 1: Firmware upgrade page
OEM webpage at 192.168.0.1
username and password "admin"
Navigate to Network Setting --> Tools --> Firmware
Click Browse and select the factory.dlf image
Click Continue to confirm and wait 6 minutes or more...
Method 2: Serial console to load TFTP image:
(see TFTP recovery)
**Return to OEM:**
Unlike most Engenius boards, this does not have a 'failsafe' image
the only way to return to OEM is serial access to uboot
Unlike most Engenius boards, public images are not available...
so the only way to return to OEM is to have a copy
of the MTD partition "firmware" BEFORE flashing openwrt.
**TFTP recovery:**
Unlike most Engenius boards, TFTP is reliable here
however it requires serial console access
(soldering pins to the UART pinouts)
build your own image...
with 'ramdisk' selected under 'Target Images'
rename initramfs-kernel.bin to 'uImageESR-600H'
make the file available on a TFTP server at 192.168.99.8
interrupt boot by holding or pressing '4' in serial console
as soon as board is powered on
`tftpboot 0x81000000`
`bootm 0x81000000`
perform a sysupgrade
**Format of OEM firmware image:**
This Engenius board uses the Senao proprietary header
with a unique Product ID. The header for factory.bin is
generated by the mksenaofw program included in openwrt.
.dlf file extension is also required for OEM software to accept it
**Note on using OKLI:**
the kernel is now too large for the bootloader to handle
so OKLI is used via the `kernel-loader` image command
recently in master several other ramips boards have the same problem
'Kernel panic - not syncing: Failed to find ralink,rt3883-sysc node'
see commit ad19751edc
Signed-off-by: Michael Pratt <mcpratt@pm.me>
Most of Build/elecom-wrc-factory and Build/elecom-wrc-gs-factory are
nearly equal, Unify those definitions by using "-N" option of mkhash and
splitting the appending text at the end of firmware image for WRC-GS/GST
devices.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
The GL-MT1300 is a high-performance new generation pocket-sized router
that offers a powerful hardware and first-class cybersecurity protocol
with unique and modern design.
Specifications:
- SoC: MT7621A, Dual-Core @880MHz
- RAM: 256 MB DDR3
- Flash: 32 MB
- Ethernet: 3 x 10/100/1000: 2 x LAN + 1 x WAN
- Wireless: 1 x MT7615D Dual-Band 2.4GHz(400Mbps) + 5GHz(867Mbps)
- USB: 1 x USB 3.0 port
- Slot: 1 x MicroSD card slot
- Button: 1 x Reset button
- Switch: 1 x Mode switch
- LED: 1 x Blue LED + 1 x White LED
MAC addresses based on vendor firmware:
WAN : factory 0x4000
LAN : Mac from factory 0x4000 + 1
2.4GHz : factory 0x4
5GHz : Mac form factory 0x4 + 1
Flashing instructions:
1.Connect to one of LAN ports.
2.Set the static IP on the PC to 192.168.1.2.
3.Press the Reset button and power the device (do not release the button).
After waiting for the blue led to flash 5 times, the white led will
come on and release the button.
4.Browse the 192.168.1.1 web page and update firmware according to web
tips.
5.The blue led will flash when the firmware is being upgraded.
6.The blue led stops blinking to indicate that the firmware upgrade is
complete and U-Boot automatically starts the firmware.
For more information on GL-MT1300, see the OFFICIAL GL.iNet website:
https://www.gl-inet.com/products/gl-mt1300/
Signed-off-by: Xinfa Deng <xinfa.deng@gl-inet.com>
[add input-type for switch, wrap long line in 10_fix_wifi_mac]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This aligns the device/image names of the older Xiaomi Mi Router
devices with their "friendly" model and DEVICE_MODEL properties.
This also reintroduces consistency with the newer devices already
following that scheme.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Specifications:
SoC: MediaTek MT7621ST (880 MHz)
FLASH: 16 MiB (Macronix MX25L12835FM2I-10G)
RAM: 128 MiB (Nanya NT5CB64M16FP-DH)
WiFi: MediaTek MT7603EN bgn 2x2:2
WiFi: MediaTek MT7612EN an 2x2:2
BTN: Reset, WPS
LED: - Power
- WiFi 2.4 GHz
- WiFi 5 GHz
- WAN
- LAN {1-4}
- USB {1-2}
UART: UART is present as pin hole next to the aluminium capacitor.
3V3 - RX - GND - TX / 115200-8N1
3V3 is the nearest on the aluminium capacitor and nut hole (pin1).
USB: 2 ports
POWER: 12VDC, 1.5A (Barrel 5.5x2.1)
Installation:
Via TFTP:
Set your computers IP-Address to 192.168.1.75
Power up the Router with the Reset button pressed.
Release the Reset button after 5 seconds.
Upload OpenWRT sysupgrade image via TFTP:
tftp -4 -v -m binary 192.168.1.1 -c put IMAGE
MAC addresses:
0x4 *:98 2g/wan, label
0x22 *:9c
0x28 *:98
0x8004 *:9c 5g/lan
Though addresses are written to 0x22 and 0x28, it appears that the
vendor firmware actually only uses 0x4 and 0x8004. Thus, we do the
same here.
Signed-off-by: Pavel Chervontsev <cherpash@gmail.com>
[add MAC address overview, add label-mac-device, fix IMAGE_SIZE]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
custom-initramfs-uimage was replaced by calls to uImage, but apparently
mtc_wr1201 was missed in the transistion. Use uImage for this device
too.
Fixes: 9f574b1b87 "ramips: mt7621: drop custom uImage function"
Signed-off-by: Sander Vanheule <sander@svanheule.net>
This commit adds support for Xiaomi's Mi Router 4C device.
Specifications:
- CPU: MediaTek MT7628AN (580MHz)
- Flash: 16MB
- RAM: 64MB DDR2
- 2.4 GHz: IEEE 802.11b/g/n with Integrated LNA and PA
- Antennas: 4x external single band antennas
- WAN: 1x 10/100M
- LAN: 2x 10/100M
- LEDs: 2x yellow/blue. Programmable (labelled as power on case)
- Non-programmable (shows WAN activity)
- Button: Reset
How to install:
1- Use OpenWRTInvasion to gain telnet and ftp access.
2- Push openwrt firmware to /tmp/ using ftp.
3- Connect to router using telnet. (IP: 192.168.31.1 -
Username: root - No password)
4- Use command "mtd -r write /tmp/firmware.bin OS1" to flash into
the router..
5- It takes around 2 minutes. After that router will restart itself
to OpenWrt.
Signed-off-by: Ataberk Özen <ataberkozen123@gmail.com>
[wrap commit message, bump PKG_RELEASE for uboot-envtools, remove
dts-v1 from DTS, fix LED labels]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Use the mkimage argument overrides provided by uImage to implement the
customisations required for the initramfs, instead of the near-identical
custom function.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
TL-MR6400v5 is very similar to TL-MR6400v4. Main differences are:
- smaller form factor
- different LED GPIOs
- different switch connections
You can flash via tftp recovery:
- serve tftp-recovery image as /tp_recovery.bin on 192.168.0.225/24
- connect to any ethernet port
- power on the device while holding the reset button
- wait at least 8 seconds before releasing reset button
Flashing via OEM web interface does not work.
LTE module does not support DHCP so it must be configured via QMI.
Hardware Specification (v5.0 EU):
- SoC: MT7628NN
- Flash: Winbond W25Q64JVS (8MiB)
- RAM: ESMT M14D5121632A (64MiB)
- Wireless: SoC platform only (2.4GHz b/g/n, 2x internal antenna)
- Ethernet: 1NIC (4x100M)
- WWAN: TP-LINK LTE MODULE (2x external detachable antenna)
- Power: DC 9V 0.85A
Signed-off-by: Filip Moc <lede@moc6.cz>
You can flash via tftp recovery:
- serve tftp-recovery image as /tp_recovery.bin on 192.168.0.225/24
- connect to any ethernet port
- power on the device while holding the reset button
- wait at least 8 seconds before releasing reset button
Flashing via OEM web interface does not work.
LTE module does not support DHCP so it must be configured via QMI.
Hardware Specification (v4.0 EU):
- SoC: MT7628NN
- Flash: Winbond W25Q64JVS (8MiB)
- RAM: ESMT M14D5121632A (64MiB)
- Wireless: SoC platform only (2.4GHz b/g/n, 2x internal antenna)
- Ethernet: 1NIC (4x100M)
- WWAN: TP-LINK LTE MODULE (2x external detachable antenna)
- Power: DC 9V 0.85A
Signed-off-by: Filip Moc <lede@moc6.cz>
This patch adds support for the WiFi Pineapple Mark 7, a wireless
penetration testing tool.
Specifications:
* SoC: MediaTek MT7628 (580MHz)
* RAM: 256MiB (DDR2)
* Storage 1: 32MiB NOR (SPI)
* Storage 2: 2GB eMMC
* Wireless 1: 802.11b/g/n 2.4GHz (Built In)
* Wireless 2: 802.11b/g/n 2.4GHz (MT7601)
* Wireless 3: 802.11b/g/n 2.4GHz (MT7601)
* USB: 1x USB Type-A 2.0 Host Port
* Ethernet: 1x USB Type-C AX88772C Ethernet
* UART: 57600 8N1 on PCB
* Inputs: 1x Reset Button
* Outputs: 1x RGB LED
* FCCID: 2AA52MK7
Flash Instructions:
Original firmware is based on OpenWRT.
Use sysupgrade via SSH to flash.
Signed-off-by: Marc Egerton <foxtrot@realloc.me>
[pepe2k@gmail.com: set only required/used gpio groups to gpio function]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
This device has previously been supported by the image
for Xiaomi Mi Router 3G v2. Since this is not obvious, the
4A is marketed as a new major revision and it also seems to
have a different bootloader, this will be both more tidy and
more helpful for the users.
Apart from that, note that there also is a 100M version of
the device that uses mt7628 platform, so a specifically named
image will also prevent confusion in this area.
Specifications:
- SoC: MediaTek MT7621
- Flash: 16 MiB NOR SPI
- RAM: 128 MiB DDR3
- Ethernet: 3x 10/100/1000 Mbps (switched, 2xLAN + WAN)
- WIFI0: MT7603E 2.4GHz 802.11b/g/n
- WIFI1: MT7612E 5GHz 802.11ac
- Antennas: 4x external (2 per radio), non-detachable
- LEDs: Programmable "power" LED (two-coloured, yellow/blue)
Non-programmable "internet" LED (shows WAN activity)
- Buttons: Reset
Installation:
Bootloader won't accept any serial input unless "boot_wait" u-boot
environment variable is changed to "on".
Vendor firmware won't accept any serial input until "uart_en" is
set to "1".
Using the https://github.com/acecilia/OpenWRTInvasion exploit you
can gain access to shell to enable these options:
To enable uart keyboard actions - 'nvram set uart_en=1'
To make uboot delay boot work - 'nvram set boot_wait=on'
Set boot delay to 5 - 'nvram set bootdelay=5'
Then run 'nvram commit' to make the changes permanent.
Once in the shell (following the OpenWRTInvasion instructions) you
can then run the following to flash OpenWrt and then reboot:
'cd /tmp; curl https://downloads.openwrt.org/...-sysupgrade.bin
--output firmware.bin; mtd -e OS1 -r write firmware.bin OS1'
Suggested-by: David Bentham <db260179@gmail.com>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This patch adds support for D-Link DIR-2640 A1.
Specifications:
* Board: AP-MTKH7-0002
* SoC: MediaTek MT7621AT
* RAM: 256 MB (DDR3)
* Flash: 128 MB (NAND)
* WiFi: MediaTek MT7615N (x2)
* Switch: 1 WAN, 4 LAN (Gigabit)
* Ports: 1 USB 2.0, 1 USB 3.0
* Buttons: Reset, WPS
* LEDs: Power (blue/orange), Internet (blue/orange), WiFi 2.4G (blue),
WiFi 5G (blue), USB 3.0 (blue), USB 2.0 (blue)
Notes:
* WiFi 2.4G and WiFi 5G LEDs are wired directly to the wireless chips
Installation:
* D-Link Recovery GUI: power down the router, press and hold the reset
button, then re-plug it. Keep the reset button pressed until the power
LED starts flashing orange, manually assign a static IP address under
the 192.168.0.xxx subnet (e.g. 192.168.0.2) and go to http://192.168.0.1
* Some modern browsers may have problems flashing via the Recovery GUI,
if that occurs consider uploading the firmware through cURL:
curl -v -i -F "firmware=@file.bin" 192.168.0.1
MAC addresses:
lan factory 0xe000 *:a7 (label)
wan factory 0xe006 *:aa
2.4 factory 0xe000 +1 *:a8
5.0 factory 0xe000 +2 *:a9
Seems like vendor didn't replace the dummy entries in the calibration data.
Signed-off-by: James McGuire <jamesm51@gmail.com>
[fix device definition title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
- minimal built initramfs: 11MB vmlinux ELF -> 4.5MB vmlinuz
- ~5 seconds for kernel decompression, which was equivalent to the
additional time to load the uncompressed ELF from SPI NOR.
- Removes requirement for lzma-loader, which may have been causing some
image builds to fail to boot on Mikrotik mt7621.
Fixes: FS#3354
Suggested-by: Thibaut VARÈNE <hacks@slashdirt.org>
Signed-off-by: John Thomson <git@johnthomson.fastmail.com.au>
Same hardware as Phicomm K2G but different flash layout.
Specification:
- SoC: MediaTek MT7620A
- Flash: 8 MB
- RAM: 64 MB
- Ethernet: 4 FE ports and 1 GE port (RTL8211F on port 5)
- Wireless radio: MT7620 for 2.4G and MT7612E for 5G, both equipped
with external PA.
- UART: 1 x UART on PCB - 57600 8N1
Flash instruction:
To avoid requiring UART for TFTP a dual flash procedure is suggested
to install the squashfs image:
1. Rename openwrt-ramips-mt7620-wavlink_wl-wn530hg4-initramfs-kernel.bin
to WN530HG4-WAVLINK.
2. Flash this file with the factory web interface.
3. With OpenWRT now running use standard sysupgrade to install the
squashfs image.
Signed-off-by: Nuno Goncalves <nunojpg@gmail.com>
[remove dts-v1, remove model from LED labels, wrap commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Specifications:
- SoC: MT7621AT
- RAM: 256MB
- Flash: 16MB (EN25QH128A)
- Ethernet: 5xGbE
- WiFi: MT7915 2x2 2.4G 573.5Mbps + 2x2 5G 1201Mbps
Known issue:
MT7915 DBDC variant isn't supported yet.
Flash instruction:
Upload the sysupgrade firmware to the firmware upgrade page in
vendor fw.
Other info:
MT7915 seems to have two PCIEs connected to MT7621. Card detected on
PCIE0 has an ID of 14c3:7916 and the other one on PCIE1 has 14c3:7915.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
TP-Link RE200 v4 is a wireless range extender with Ethernet and 2.4G and 5G
WiFi with internal antennas.
It's based on MediaTek MT7628AN+MT7610EN like the v2/v3.
Specifications
--------------
- MediaTek MT7628AN (580 Mhz)
- 64 MB of RAM
- 8 MB of FLASH
- 2T2R 2.4 GHz and 1T1R 5 GHz
- 1x 10/100 Mbps Ethernet
- 8x LED (GPIO-controlled), 2x button
- UART connection holes on PCB (57600 8n1)
There are 2.4G and 5G LEDs in red and green which are controlled
separately.
MAC addresses
-------------
The MAC address assignment matches stock firmware, i.e.:
LAN : *:8E
2.4G: *:8D
5G : *:8C
MAC address assignment has been done according to the RE200 v2.
The label MAC address matches the OpenWrt ethernet address.
Installation
------------
Web Interface
-------------
It is possible to upgrade to OpenWrt via the web interface. Simply flash
the -factory.bin from OEM. In contrast to a stock firmware, this will not
overwrite U-Boot.
Recovery
--------
Unfortunately, this devices does not offer a recovery mode or a tftp
installation method. If the web interface upgrade fails, you have to open
your device and attach serial console.
Instructions for serial console and recovery may be checked out in
commit 6d6f36ae78 ("ramips: add support for TP-Link RE200 v2") or on
the device's Wiki page.
Signed-off-by: Richard Fröhning <misanthropos@gmx.de>
[removed empty line, fix commit message formatting]
Signed-off-by: David Bauer <mail@david-bauer.net>
This submission relied heavily on the work of
Santiago Rodriguez-Papa <contact at rodsan.dev>
Specifications:
* SoC: MediaTek MT7621A (880 MHz 2c/4t)
* RAM: Winbond W632GG6MB-12 (256M DDR3-1600)
* Flash: Winbond W29N01HVSINA (128M NAND)
* Eth: MediaTek MT7621A (10/100/1000 Mbps x5)
* Radio: MT7603E/MT7615N (2.4 GHz & 5 GHz)
4 antennae: 1 internal and 3 non-deatachable
* USB: 3.0 (x1)
* LEDs:
White (x1 logo)
Green (x6 eth + wps)
Orange (x5, hardware-bound)
* Buttons:
Reset (x1)
WPS (x1)
Installation:
Flash factory image through GUI.
This might fail due to the A/B nature of this device. When flashing, OEM
firmware writes over the non-booted partition. If booted from 'A',
flashing over 'B' won't work. To get around this, you should flash the
OEM image over itself. This will then boot the router from 'B' and
allow you to flash OpenWRT without problems.
Reverting to factory firmware:
Hard-reset the router three times to force it to boot from 'B.' This is
where the stock firmware resides. To remove any traces of OpenWRT from
your router simply flash the OEM image at this point.
Signed-off-by: J. Scott Heppler <shep971@centurylink.net>
The RAVPower RP-WD03 is a battery powered router, with an Ethernet and
USB port. Due due a limitation in the vendor supplied U-Boot bootloader,
we cannot exceed a 1.5 MB kernel size, as is the case with recent builds
(i.e. post v19.07). This breaks both factory and sysupgrade images.
To address this, use the lzma loader (loader-okli) to work around this
limitation.
The improvements here also address the "misplaced" U-Boot environment
partition, which is located between the kernel and rootfs in the stock
image / implementation. This is addressed by making use of mtd-concat,
maximizing space available in the booted image.
This will make sysupgrade from earlier versions impossible.
Changes are based on the recently supported HooToo HT-TM05, as the
hardware is almost identical (except for RAM size) and is from the same
vendor (SunValley). While at it, also change the SPI frequency
accordingly.
Installation:
- Download the needed OpenWrt install files, place them in the root
of a clean TFTP server running on your computer. Rename the files as,
- openwrt-ramips-mt7620-ravpower_rp-wd03-squashfs-kernel.bin => kernel
- openwrt-ramips-mt7620-ravpower_rp-wd03-squashfs-rootfs.bin => rootfs
- Plug the router into your computer via Ethernet
- Set your computer to use 10.10.10.254 as its IP address
- With your router shut down, hold down the power button until the first
white LED lights up.
- Push and hold the reset button and release the power button. Continue
holding the reset button for 30 seconds or until it begins searching
for files on your TFTP server, whichever comes first.
- The router (10.10.10.128) will look for your computer at 10.10.10.254
and install the two files. Once it has finished installation, it will
automatically reboot and start up OpenWrt.
- Set your computer to use DHCP for its IP address
Notes:
- U-Boot environment can be modified, u-boot-env is preserved on initial
install or sysupgrade
- mtd-concat functionality is included, to leave a "hole" for u-boot-env,
combining the OEM kernel and rootfs partitions
Most of the changes in this commit are the work of Russell Morris (as
credited below), I only wrapped them up and added compat-version.
Thanks to @mpratt14 and @xabolcs for their help getting the lzma loader
to work!
Fixes: 5ef79af4f8 ("ramips: add support for Ravpower WD03")
Suggested-by: Russell Morris <rmorris@rkmorris.us>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This reverts commit e81e625ca3.
This was meant just for early DSA-adopters. Those should have
updated by now, remove it so future updaters get the intended
experience.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This patch adds support for D-Link DIR-2660 A1.
Specifications:
* Board: AP-MTKH7-0002
* SoC: MediaTek MT7621AT
* RAM: 256 MB (DDR3)
* Flash: 128 MB (NAND)
* WiFi: MediaTek MT7615N (x2)
* Switch: 1 WAN, 4 LAN (Gigabit)
* Ports: 1 USB 2.0, 1 USB 3.0
* Buttons: Reset, WPS
* LEDs: Power (white/orange), Internet (white/orange), WiFi 2.4G (white),
WiFi 5G (white), USB 3.0 (white), USB 2.0 (white)
Notes:
* WiFi 2.4G and WiFi 5G LEDs are wired directly to the wireless chips
Installation:
* D-Link Recovery GUI: power down the router, press and hold the reset
button, then re-plug it. Keep the reset button pressed until the power
LED starts flashing orange, manually assign a static IP address under
the 192.168.0.xxx subnet (e.g. 192.168.0.2) and go to http://192.168.0.1
* Some modern browsers may have problems flashing via the Recovery GUI,
if that occurs consider uploading the firmware through cURL:
curl -v -i -F "firmware=@file.bin" 192.168.0.1
MAC addresses:
lan factory 0xe000 *:a7 (label)
wan factory 0xe006 *:aa
2.4 factory 0xe000 +1 *:a8
5.0 factory 0xe000 +2 *:a9
Seems like vendor didn't replace the dummy entries in the calibration data.
Signed-off-by: Josh Bendavid <joshbendavid@gmail.com>
[rebase onto already merged DIR-1960 A1, add MAC addresses to commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The HooToo HT-TM05 is a battery powered router, with an Ethernet and USB port.
Vendor U-Boot limited to 1.5 MB kernel size, so use lzma loader (loader-okli).
Specifications:
SOC: MediaTek MT7620N
BATTERY: 10400mAh
WLAN: 802.11bgn
LAN: 1x 10/100 Mbps Ethernet
USB: 1x USB 2.0 (Type-A)
RAM: 64 MB
FLASH: GigaDevice GD25Q64, Serial 8 MB Flash, clocked at 50 MHz
Flash itself specified to 80 MHz, but speed limited by mt7620 SPI
fast-read enabled (m25p)
LED: Status LED (blue after boot, green with WiFi traffic
4 leds to indicate power level of the battery (unable to control)
INPUT: Power, reset button
MAC assignment based on vendor firmware:
2.4 GHz *:b4 (factory 0x04)
LAN/label *:b4 (factory 0x28)
WAN *:b5 (factory 0x2e)
Tested and working:
- Ethernet
- 2.4 GHz WiFi (Correct MAC-address)
- Installation from TFTP (recovery)
- OpenWRT sysupgrade (Preserving and non-preserving), through the usual
ways: command line and LuCI
- LEDs (except as noted above)
- Button (reset)
- I2C, which is needed for reading battery charge status and level
- U-Boot environment / variables (from U-Boot, and OpenWrt)
Installation:
- Download the needed OpenWrt install files, place them in the root
of a clean TFTP server running on your computer. Rename the files as,
- ramips-mt7620-hootoo_tm05-squashfs-kernel.bin => kernel
- ramips-mt7620-hootoo_tm05-squashfs-rootfs.bin => rootfs
- Plug the router into your computer via Ethernet
- Set your computer to use 10.10.10.254 as its IP address
- With your router shut down, hold down the power button until the first
white LED lights up.
- Push and hold the reset button and release the power button. Continue
holding the reset button for 30 seconds or until it begins searching
for files on your TFTP server, whichever comes first.
- The router (10.10.10.128) will look for your computer at 10.10.10.254
and install the two files. Once it has finished installation, it will
automatically reboot and start up OpenWrt.
- Set your computer to use DHCP for its IP address
Notes:
- U-Boot environment can be modified, u-boot-env is preserved on initial
install or sysupgrade
- mtd-concat functionality is included, to leave a "hole" for u-boot-env,
combining the OEM kernel and rootfs partitions
I would like to thank @mpratt14 and @xabolcs for their help getting the
lzma loader to work!
Signed-off-by: Russell Morris <rmorris@rkmorris.us>
[drop changes in image/Makefile, fix indent and PKG_RELEASE in
uboot-envtools, fix LOADER_FLASH_OFFS, minor commit message facelift,
add COMPILE to Device/Default]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
FLASH_START is supposed to point at the memory area where NOR flash are
mapped. We currently have an incorrect FLASH_START copied from ar71xx
back then and the loader doesn't work under OKLI mode.
On ramips, mt7621 has it's flash mapped to 0x1fc00000 and other SoCs
uses 0x1c000000. This commit makes FLASH_START a configurable value to
handle both cases.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
The DIR-645 fails to boot if the kernel is large.
Enabling lzma-loader resolves the issue.
Run-tested on D-Link DIR-645.
Signed-off-by: Perry Melange <isprotejesvalkata@gmail.com>
This patch adds support for Wavlink WL-WN531A6 (Quantum D6).
Specifications:
--------------
* SoC: Mediatek MT7621AT 2C2T, 880MHz
* RAM: 128MB DDR3, Nanya NT5CB64M16GP-EK
* Flash: 16MB SPI NOR flash, GigaDevice GD25Q127CSIG
* WiFi 5GHz: Mediatek MT7615N (4x4:4) on mini PCIE slot.
* WiFi 2.4GHz: Mediatek MT7603EN (2x2:2) on mini PCIE slot.
* Ethernet: MT7630, 5x 1000Base-T
* LED: Power, WAN, LAN(x4), WiFi, WPS, dual color
"WAVLINK" LED logo on the top cover.
* Buttons: Reset, WPS, "Turbo", touch button on the top
cover via RH6015C touch sensor.
* UART: UART1: serial console (57600 8n1) on the J4 header
located below the top heatsink.
UART2: J12 header, located on the right side of
the board.
* USB: One USB3 port.
* I2C: J9 header, located below the top heatsink.
Backup the OEM Firmware:
-----------------------
There isn't any firmware released for the WL-WN531A6 on
the Wavlink web site. Reverting back to the OEM firmware is
not possible unless we have a backup of the original OEM
firmware.
The OEM firmware is stored on /dev/mtd4 ("Kernel").
1) Plug a FAT32 formatted USB flash drive into the USB port.
2) Navigate to "Setup->USB Storage". Under the "Available
Network folder" you can see part of the mount point of
the newly mounted flash drive filesystem - e.g "sda1".
The full mount point is prefixed with "/media", so in
this case the mount point becomes "/media/sda1".
3) Go to http://192.168.10.1/webcmd.shtml .
4) Type the following line in the "Command" input box:
dd if=/dev/mtd4ro of=/media/sda1/firmware.bin
5) Click "Apply"
6) After few seconds, in the text area should appear this
output:
30080+0 records in
30080+0 records out
7) Type "sync" in the "Command" input box and click "Apply".
8) At this point the OEM firmware is stored on the flash
drive as "firmware.bin". The size of the file is 15040 KB.
Installation:
------------
* Flashing instructions (OEM web interface):
The OEM web interface accepts only files with names containing
"WN531A6". It's also impossible to flash the *-sysupgrade.bin
image, so we have to flash the *-initramfs-kernel.bin first and
use the OpenWrt's upgrade interface to write the sysupgrade
image.
1) Rename openwrt-ramips-mt7621-wavlink_wl-wn531a6-initramfs-kernel.bin
to WN531A6.bin.
2) Connect your computer to the one of the LAN ports of the
router with an Ethernet cable and open http://192.168.10.1
3) Browse to Setup -> Firmware Upgrade interface.
4) Upload the (renamed) OpenWrt image - WN531A6.bin.
5) Proceed with the firmware installation and give the device
a few minutes to finish and reboot.
6) After reboot wait for the "WAVLINK" logo on the top cover
to turn solid blue, and open http://192.168.1.1
7) Use the OpenWrt's "Flash Firmware" interface to write the
OpenWrt sysupgrade image:
openwrt-ramips-mt7621-wavlink_wl-wn531a6-squashfs-sysupgrade.bin
* Flashing instructions (u-boot TFTP):
1) Configure a TFTP server on your computer and set its IP
to 192.168.10.100
2) Rename the OpenWrt sysupgrade image to firmware.bin and
place it in the root folder of the TFTP server.
3) Power off the device and connect an Ethernet cable from
one of its LAN ports your computer.
4) Press the "Reset" button (and keep it pressed)
5) Power on the device.
6) After a few seconds, when the connected port LAN LED stops
blinking fast, release the "Reset" button.
7) Flashing OpenWrt takes less than a minute, system will
reboot automatically.
8) After reboot the WAVLINK logo on the top cover will indicate
the current OpenWrt running status (wait until the logo tunrs
solid blue).
Revert to the OEM Firmware:
--------------------------
* U-boot TFTP:
Follow "Flashing instructions (u-boot TFTP)" and use the
"firmware.bin" backup image.
* OpenWrt "Flash Firmware" interface:
Upload the "firmware.bin" backup image and select "Force update"
before continuing.
Notes:
-----
* The MAC address shown on the label at the back of the device
is assigned to the 2.4G WiFi adapter.
MAC addresses assigned by the OEM firmware:
2.4G: *:XX (label): factory@0x0004
5G: *:XX + 1 : factory@0x8004
WAN: *:XX - 1 : factory@0xe006
LAN: *:XX - 2 : factory@0xe000
* The I2C bus and UART2 are fully functional. The headers are
not populated.
Signed-off-by: Georgi Vlaev <georgi.vlaev@konsulko.com>
This patch adds support for the TP-Link TL-WR850N v2. This device
is very similar to TP-Link TL-WR840 v4 and TP-Link TL-WR841 v13.
Specifications:
SOC: MediaTek MT7628NN
Flash: 8 MiB SPI
RAM: 64 MiB
WLAN: MediaTek MT7628NN
Ethernet: 5 ports (100M)
Installation Using the integrated tftp capability of the router:
1. Turn off the router.
2. Connect pc to one of the router LAN ports.
3. Set your PC IPv4 address to 192.168.0.66/24.
4. Run any TFTP server on the PC.
5. Put the recovery firmware on the root directory of TFTP server
and name the file tp_recovery.bin
6. Start the router by pressing power button while holding the
WPS/Reset button (or both WPS/Reset and WIFI buttons)
7. Router connects to your PC with IPv4 address 192.168.0.2,
downloads the firmware, installs it and reboots. LEDs are
flashing. Now you have OpenWrt installed.
8. Change your IPv4 PC address to something in 192.168.1.0/24
network or use DHCP to get an address from your OpenWrt router.
9. Done! You can login to your router via ssh.
Forum link:
https://forum.openwrt.org/t/add-support-for-tp-link-tl-wr850n-v2/66899
Signed-off-by: Andrew Freeman <labz56@gmail.com>
[squash an tidy up commits, sort nodes]
Signed-off-by: Darsh Patel <darshkpatel@gmail.com>
[minor commit message adjustments]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The wg3526 fails to boot if the kernel is large.
Enabling lzma-loader resolves the issue on both the wg3526-16m
and wg3526-32m.
Fixes: FS#3143
Signed-off-by: Rustam Gaptulin <rascal6@gmail.com>
[commit message facelift]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
In order to support SAE/WPA3-Personal in default images. Replace almost
all occurencies of wpad-basic and wpad-mini with wpad-basic-wolfssl for
consistency. Keep out ar71xx from the list as it won't be in the next
release and would only make backports harder.
Build-tested (build-bot settings):
ath79: generic, ramips: mt7620/mt76x8/rt305x, lantiq: xrx200/xway,
sunxi: a53
Signed-off-by: Petr Štetiar <ynezz@true.cz>
[rebase, extend commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This patch adds support for the MikroTik RouterBOARD 760iGS router.
It is similar to the already supported RouterBOARD 750Gr3.
The 760iGS device features an added SFP cage, and passive
PoE out on port 5 compared to the RB750Gr3.
https://mikrotik.com/product/hex_s
Specifications:
- SoC: MediaTek MT7621A
- CPU: 880MHz
- Flash: 16 MB
- RAM: 256 MB
- Ethernet: 5x 10/100/1000 Mbps
- SFP cage
- USB port
- microSD slot
Unsupported:
- Beeper (requires PWM driver)
- ZT2046Q (ADS7846 compatible) on SPI as slave 1 (CS1)
The linux driver requires an interrupt, and pendown GPIO
These are unknown, and not needed with the touchscreen
only used for temperature and voltage monitoring.
ads7846 hwmon:
temp0 is degrees Celsius
temp1 is voltage * 32
GPIOs:
- 07: input passive PoE out (lan5) compatible (Mikrotik) device connected
- 17: output passive PoE out (lan5) switch
Installation through RouterBoot follows the usual MikroTik method
https://openwrt.org/toh/mikrotik/common
To boot to intramfs image in RAM:
1. Setup TFTP server to serve intramfs image.
2. Plug Ethernet cable into WAN port.
3. Unplug power, hold reset button and plug power in.
Wait (~25 seconds) for beep and then release reset button.
The SFP LED will be lit in RouterBoot, but will not be lit in OpenWRT.
4. Wait for a minute. Router should be running OpenWrt,
check by plugging in to port 2-5 and going to 192.168.1.1.
To install OpenWrt to flash:
1. Follow steps above to boot intramfs image in RAM.
2. Flash the sysupgrade.bin image with web interface or sysupgrade.
3. Once the router reboots you will be running OpenWrt from flash.
OEM firmware differences:
- RouterOS assigns a different MAC address for each port
- The first address (E01 on the sticker) is used for wan (ether1 in OEM).
- The next address is used for lan2.
- The last address (E06 on the sticker) is used for sfp.
[Initial port work, shared dtsi]
Signed-off-by: Vince Grassia <vincenzo.grassia@zionark.com>
[SFP support and GPIO identification]
Signed-off-by: Luka Logar <luka.logar@iname.com>
[Misc. fixes and submission]
Signed-off-by: John Thomson <git@johnthomson.fastmail.com.au>
[rebase, drop uart3 from state_default on 750gr3, minor commit
title/message facelift]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This beeper hardware requires a PWM driver for frequency selection.
Since the GPIO driver does not provide that, revert the beeper
support to a simple gpio-export.
This effectively reverts the corresponding changes from
6ba58b7b02 ("ramips: cleanup the RB750Gr3 support")
Signed-off-by: John Thomson <git@johnthomson.fastmail.com.au>
[commit title/message facelift]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
A bunch of kernel modules depends on kmod-usb-net, but does not
select it. Make AddDepends/usb-net selective, so we can drop
some redundant +kmod-usb-net definitions for DEVICE_PACKAGES.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Add a specific comment for early DSA-adopters that they can keep
their config when prompted due to compat-version increase.
This is a temporary solution, the patch should be simply reverted
before any release.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This implements the newly introduced compat-version to prevent
broken upgrade between swconfig and DSA for ramips' mt7621 subtarget.
In order to make the situation more transparent for the user, and
to prevent large switch-cases for devices, it is more convenient to
have the entire subtarget 1.1-by-default. This means that new devices
will be added with 1.1 from the start, but in contrast we don't need
to switch them in board.d files. Apart from that, users that manually
backport devices to 19.07 with swconfig will have an equivalent
upgrade experience to officially supported devices.
Since DSA support on mt7621 is out for a while already, this applies
the same uci-defaults workaround for early adopters as already
done for kirkwood and mvebu in previous commits.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The bootloader fails to extract a big kernel, e.g. v5.4 kernel image
with ALL_KMODS enabled. This can be fixed by using lzma-loader.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Currently the lzma-loader is placed in RAM at 32MB offset, which does not
make sense for devices with only 32MB RAM. If we adjust LZMA_TEXT_START to
24MB offset, then the lzma-loader can be used on those devices and still
about 24MB memory will be available for uncompressed image, which should be
enough for most use cases.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
For ramips/mt7621, the wpad-basic package is not selected by default,
but added for every device individually as needed.
While this might be technically correct if the SoC does not come with
a Wifi module, only 18 of 97 devices for that platform are set up
_without_ wpad-basic currently.
Therefore, it seems more convenient to add wpad-basic by default for
the subtarget and then just remove it for the 18 mentioned devices,
instead of having to add it for about 60 times instead.
This would also match the behavior of the 5 other subtargets, where
wpad-basic/wpad-mini is added by default as well, and thus be more
obvious to developers without detailed SoC knowledge.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Specification:
- CPU: MediaTek MT7620N (580 MHz)
- Flash size: 4 MB NOR SPI
- RAM size: 32 MB DDR1
- Bootloader: U-Boot
- Wireless: MT7620N 2x2 MIMO 802.11b/g/n (2.4 GHz)
- Switch: MT7620 built-in 10/100 switch with vlan support
- Ports: 4x LAN, 1x WAN
- Others: 7x LED, Reset button, UART header on PCB (57600 8N1)
Flash instructions:
1. Use ethernet cable to connect router with PC/Laptop, any router
LAN port will work.
2. To flash openwrt we are using nmrpflash[1].
3. Flash commands:
First we need to identify the correct Ethernet id.
nmrpflash -L
nmrpflash -i net* -f openwrt-ramips-mt7620-netgear_jwnr2010-v5-squashfs-factory.img
This will show something like "Advertising NMRP server on net*..." (net*, *=1,2,3... etc.)
4. Now remove the power cable from router back side and immediately connect it again.
You will see flash notification in CMD window, once it says reboot the device just
plug off the router and plug in again.
Revert to stock:
1. Download the stock firmware from official netgear support[2].
2. Follow the same nmrpflash procedure like above, this time just use the stock firmware.
nmrpflash -i net* -f N300-V1.1.0.54_1.0.1.img
MAC addresses on stock firmware:
LAN = *:28 (label)
WAN = *:29
WLAN = *:28
On flash, the only valid MAC address is found in factory 0x4.
Special Note:
This openwrt firmware will also support other netgear N300 routers like below as they
share same stock firmware[3].
JNR1010v2 / WNR614 / WNR618 / JWNR2000v5 / WNR2020 / WNR1000v4 / WNR2020v2 / WNR2050
[1] https://github.com/jclehner/nmrpflash
[2] https://www.netgear.com/support/product/JWNR2010v5.aspx
[3] http://kb.netgear.com/000059663
Signed-off-by: Shibajee Roy <ador250@protonmail.com>
[create DTSI, use netgear_sercomm_nor, disable by default, add MAC
addresses to commit message, add label MAC address]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Like NAND-based devices, SPI-NOR based Netgear devices also share
a common setup for their images. This creates a common defition
for them in image/Makefile, so it can be reused across subtargets.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
WIZnet WizFi630s board name is written slightly different it its OEM
OpenWrt firmware. This causes an incompatibility warning during flashing
with sysupgrade. This patch is adding the vendor board name to the
supported devices list to avoid this warning. For initial flashing you
can use sysupgrade via command line or luci beside of TFTP.
Do not keep the OEM configuration during sysupgrade.
Signed-off-by: Tobias Welz <tw@wiznet.eu>
TP-Link RE200 v3 is a wireless range extender with Ethernet and 2.4G and 5G
WiFi with internal antennas. It's based on MediaTek MT7628AN+MT7610EN like the v2.
Specifications
--------------
- MediaTek MT7628AN (580 Mhz)
- 64 MB of RAM
- 8 MB of FLASH
- 2T2R 2.4 GHz and 1T1R 5 GHz
- 1x 10/100 Mbps Ethernet
- 8x LED (GPIO-controlled), 2x button
Unverified:
- UART header on PCB (57600 8n1)
There are 2.4G and 5G LEDs in red and green which are controlled
separately.
MAC addresses
-------------
MAC address assignment has been done according to the RE200 v2.
The label MAC address matches the OpenWrt ethernet address.
Installation
------------
Web Interface
-------------
It is possible to upgrade to OpenWrt via the web interface. Simply flash
the -factory.bin from OEM. In contrast to a stock firmware, this will not
overwrite U-Boot.
Recovery
--------
Unfortunately, this devices does not offer a recovery mode or a tftp
installation method. If the web interface upgrade fails, you have to open
your device and attach serial console.
The device has not been opened for adding support. However, it is expected
that the behavior is similar to the RE200 v2. Instructions for serial console
and recovery may be checked out in commit 6d6f36ae78 ("ramips: add support
for TP-Link RE200 v2") or on the device's Wiki page.
Signed-off-by: Richard Fröhning <misanthropos@gmx.de>
[adjust commit title/message, sort support list]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
For the TP-Link 4M devices with tplink-v2-image recipe
(mktplinkfw2.c), there are two different flash layouts based
on the size of the (u)boot partition:
device uboot OEM firmware OpenWrt (incl. config)
tl-wr840n-v5 0x20000 0x3c0000 0x3d0000
tl-wr841n-v14 0x10000 0x3d0000 0x3e0000
In both cases, the 0x10000 config partition is used for the firmware
partition as well due to the limited space available and since it's
recreated by the OEM firmware anyway.
However, the TFTP flashing process will only copy data up to the
size of the initial (OEM) firmware size. Therefore, while we can
use the bigger partition to have additional erase blocks on the
device, we have to limit the image sizes to the TFTP limits.
So far, only one layout definition has been set up in mktplinkfw2.c
for 4M mediatek devices. This adds a second one and assigns them
to the devices so the image sizes are correctly restrained.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This commit adds support for the Jotale JS76x8 series development boards.
These devices have the following specifications:
- SOC: MT7628AN/NN, MT7688AN, MT7628DAN
- RAM of MT7628AN/NN and MT7688AN: 64/128/256 MB (DDR2)
- RAM of MT7628DAN: 64 MB (DDR2)
- FLASH:8/16/32 MB (SPI NOR)
- Ethernet:3x 10/100 Mbps ethernet ports (MT76x8 built-in switch)
- WIFI:1x 2T2R 2.4 GHz Wi-Fi
- LEDs:1x system status green LED, 1x wifi green LED,
3x ethernet green LED
- Buttons:1x reset button
- 1x microSD slot
- 4x USB 2.0 port
- 1x mini-usb debug UART
- 1x DC jack for main power (DC 5V)
- 1x TTL/RS232 UART
- 1x TTL/RS485 UART
- 13x GPIO header
- 1x audio codec(wm8960)
Installation via OpenWrt:
The original firmware is OpenWrt, so both LuCI and sysupgrade can be used.
Installation via U-boot web:
1. Power on board with reset button pressed, release it
after wifi led start blinking.
2. Setup static IP 192.168.1.123/4 on your PC.
3. Go to 192.168.1.8 in browser and upload "sysupgrade" image.
Installation via U-boot tftp:
1. Connect to serial console at the mini usb, which has been connected to UART0
on board (115200 8N1)
2. Setup static IP 192.168.1.123/4 on your PC.
3. Place openwrt-firmware.bin on your PC tftp server (192.168.1.123).
3. Connect one of LAN ports on board to your PC.
4. Start terminal software (e.g. screen /dev/ttyUSB0 115200) on PC.
5. Apply power to board.
6. Interrupt U-boot with keypress of "2".
7. At u-boot prompts:
Warning!! Erase Linux in Flash then burn new one. Are you sure?(Y/N) Y
Input device IP (192.168.1.8) ==:192.168.1.8
Input server IP (192.168.1.123) ==:192.168.1.123
Input Linux Kernel filename (root_uImage) ==:openwrt-firmware.bin
8. board will download file from tftp server, write it to flash and reboot.
Signed-off-by: Robinson Wu <wurobinson@qq.com>
[add license to DTS files, fix state_default and reduce to the mimimum,
move phy0tpt trigger to DTS, drop ucidef_set_led_timer, fix network ports]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This patch adds support for D-Link DIR-1960 A1. Given the similarity with
the DIR-1760/2660 A1, this patch also introduces a common DTSI which can
be shared with these devices, with support to be added in future commits.
Specifications:
* Board: AP-MTKH7-0002
* SoC: MediaTek MT7621AT
* RAM: 256 MB (DDR3)
* Flash: 128 MB (NAND)
* WiFi: MediaTek MT7615N (x2)
* Switch: 1 WAN, 4 LAN (Gigabit)
* Ports: 1 USB 3.0
* Buttons: Reset, WPS
* LEDs: Power (white/orange), Internet (white/orange), WiFi 2.4G (white),
WiFi 5G (white), USB 3.0 (white)
Notes:
* WiFi 2.4G and WiFi 5G LEDs are wired directly to the wireless chips
Installation:
* D-Link Recovery GUI: power down the router, press and hold the reset
button, then re-plug it. Keep the reset button pressed until the power
LED starts flashing orange, manually assign a static IP address under
the 192.168.0.xxx subnet (e.g. 192.168.0.2) and go to http://192.168.0.1
* Some modern browsers may have problems flashing via the Recovery GUI,
if that occurs consider uploading the firmware through cURL:
curl -v -i -F "firmware=@file.bin" 192.168.0.1
MAC addresses:
lan factory 0xe000 *:EB (label)
wan factory 0xe006 *:EE
2.4 factory 0xe000 +1 *:EC
5.0 factory 0xe000 +2 *:ED
Seems like vendor didn't replace the dummy entrys in the calibration data.
Signed-off-by: Josh Bendavid <joshbendavid@gmail.com>
[fix whitespace issues, create patch to merge DIR-1960 first, move
special WiFi MAC settings to DTS, extend commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The Winstars WS-WN583A6 is a wireless repeater with 2 gigabit ethernet
ports. Even if mine is branded as "Gemeita AC2100", the sticker on the
back says WS-WN583A6. So I will refer to it as Winstars WS-WN583A6.
Probably the real product name is the Wavlink WL-WN583A6 because of
the many references to Wavlink in the OEM firmware and bootlog.
Hardware
--------
SoC: Mediatek MT7621AT (880 MHz, 2 cores 4 threads)
RAM: 128MB
FLASH: 8MB NOR (GigaDevice GD25Q64B)
ETH: 2x 10/100/1000 Mbps Ethernet (MT7530)
WIFI:
- 2.4GHz: 1x MT7603E (2x2:2)
- 5GHz: 1x MT7615E (4x4:4)
- 6 internal antennas
BTN:
- 1x Reset button
- 1x WPS button
- 1x ON/OFF switch (working but unmodifiable)
- 1x Auto/Schedule switch (working but unmodifiable. Read Note #3)
LEDS:
- 1x White led
- 1x Red led
- 1x Amber led
- 1x Blue led
- 2x Blue leds (lan and wan port status: working but unmodifiable)
UART:
- 57600-8-N-1
Everything works correctly.
Currently there is no firmware update available. Because of this, in
order to restore the OEM firmware, you must firstly dump the OEM
firmware from your router before you flash the OpenWrt image.
Backup the OEM Firmware
-----------------------
The following steps are to be intended for users having little to none
experience in linux. Obviously there are many ways to backup the OEM
firmware, but probably this is the easiest way for this router.
Procedure tested on M83A6.V5030.191210 firmware version.
1) Go to http://192.168.10.1/webcmd.shtml
2) Type the following line in the "Command" input box:
mkdir /etc_ro/lighttpd/www/dev; for i in /dev/mtd*ro; do dd if=${i} of=/etc_ro/lighttpd/www${i}; done
3) Click "Apply"
4) After few seconds, in the textarea should appear this output:
16384+0 records in
16384+0 records out
8388608 bytes (8.0MB) copied, 4.038820 seconds, 2.0MB/s
384+0 records in
384+0 records out
196608 bytes (192.0KB) copied, 0.095180 seconds, 2.0MB/s
128+0 records in
128+0 records out
65536 bytes (64.0KB) copied, 0.032020 seconds, 2.0MB/s
128+0 records in
128+0 records out
65536 bytes (64.0KB) copied, 0.031760 seconds, 2.0MB/s
15744+0 records in
15744+0 records out
8060928 bytes (7.7MB) copied, 3.885280 seconds, 2.0MB/s
dd: can't open '/dev/mtd5ro': No such device
dd: can't open '/dev/mtd6ro': No such device
dd: can't open '/dev/mtd7ro': No such device
Excluding the "X.XXXXXX seconds" part, you should get the same
exact output. If your output doesn't match mine, stop reading
and ask for help in the forum.
5) Open the following links to download the partitions of the OEM FW:
http://192.168.10.1/dev/mtd0rohttp://192.168.10.1/dev/mtd1rohttp://192.168.10.1/dev/mtd2rohttp://192.168.10.1/dev/mtd3rohttp://192.168.10.1/dev/mtd4ro
If one (or more) of these files weight 0 byte, stop reading and ask
for help in the forum.
6) Store these downloaded files in a safe place.
7) Reboot your router to remove any temporary file from your router.
Installation
------------
Flash the initramfs image in the OEM firmware interface.
When openwrt boots, flash the sysupgrade image otherwise you won't be
able to keep configuration between reboots.
Restore OEM Firmware
--------------------
Flash the "mtd4ro" file you previously backed-up directly from LUCI.
Warning: Remember to not keep settings!
Warning2: Remember to force the flash.
Notes
-----
1) The "System Command" page allows to run every command as root.
For example you can use "dd" and "nc" to backup the OEM firmware.
PC (SERVER):
nc -l 5555 > ./mtdXro
ROUTER (CLIENT):
dd if=/dev/mtdXro | nc PC_IP_ADDRESS 5555
2) The OEM web interface accepts only images containing the string
"WN583A6" in the filename.
Currently the OEM interface accepts only the initramfs image
probably because it checks if the ih_size in the image header is
equal to the whole image size (instead of the kernel size)
Read more here:
https://forum.openwrt.org/t/support-for-strong-1200/22768/19
3) The white led (namely "Smart Night Light") can be controller by the
user only if the side switch is set to "Schedule" otherwise it will
be activated by the light condition (there is a photodiode on the
top side of the router)
4) Router mac addresses:
LAN XX:XX:XX:XX:XX:8F
WAN XX:XX:XX:XX:XX:90
WIFI 2G XX:XX:XX:XX:XX:91
WIFI 5G XX:XX:XX:XX:XX:92
LABEL XX:XX:XX:XX:XX:91
Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
[remove chosen node, fix whitespace]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This reverts commit 1623defbdb.
As already stated in the reverted patch, the OEM firmware will
properly recreate the config partition if it is overwritten by
OpenWrt.
The main reason for adding the partition was the image size
restriction imposed by the 0x3d0000 limitation of the TFTP
flashing process. Addressing this by shrinking the firmware
partition is not a good solution to that problem, though:
1. For a working image, the size of the content has to be smaller
than the available space, so empty erase blocks will remain.
2. Conceptually, the restriction is on the image, so it makes sense
to implement it in the same way, and not via the partitioning.
Users could e.g. do initial flash with TFTP restriction with
an older image, and then sysupgrade into a newer one, so TFTP
restriction does not apply.
3. The (content) size of the recovery image is enforced to 0x3d0000
by the tplink-v2-image command in combination with
TPLINK_FLASHLAYOUT (flash layout in mktplinkfw2.c) anyway.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The config partition was missing from the flash layout of the device.
Although the stock firmware resets a corrupted config partition to the
default values, the TFTP flash with an image bigger than 0x3d0000 will
truncate the image as the bootloader only copies 0x3d0000 bytes to flash
during TFTP flashing.
Fixed by adding the config partition and shrinking the firmware
partition.
Fixes: 3fd97c522b ("ramips: add support for TP-Link TL-WR841n v14")
Signed-off-by: Alexander Müller <donothingloop@gmail.com>
This patch adds support for D-Link DIR-867 A1 and D-Link DIR-882 A1. Given
the similarity of these devices, this patch also introduces a common DTS
shared between DIR-867 A1, DIR-878 A1 and DIR-882 A1.
Specifications:
* Board: AP-MTKH7-0002
* SoC: MediaTek MT7621AT
* RAM: 128 MB (DDR3)
* Flash: 16 MB (SPI NOR)
* WiFi: MediaTek MT7615N (x2)
* Switch: 1 WAN, 4 LAN (Gigabit)
* Ports: 1 USB 2.0, 1 USB 3.0
* Buttons: Reset, WiFi Toggle, WPS
* LEDs: Power (green/orange), Internet (green/orange), WiFi 2.4G (green),
WiFi 5G (green), USB 2.0 (green), USB 3.0 (green)
Notes:
* WiFi 2.4G and WiFi 5G LEDs are wired directly to the wireless chips
* DIR-867 wireless chips are limited to 3x3 streams at hardware level
* USB ports and related LEDs available only on DIR-882
Serial port:
* Parameters: 57600, 8N1
* Location: J1 header (close to the Reset, WiFi and WPS buttons)
* Pinout: 1 - VCC
2 - RXD
3 - TXD
4 - GND
Installation:
* D-Link Recovery GUI: power down the router, press and hold the reset
button, then re-plug it. Keep the reset button pressed until the power
LED starts flashing orange, manually assign a static IP address under
the 192.168.0.xxx subnet (e.g. 192.168.0.2) and go to http://192.168.0.1
* Some modern browsers may have problems flashing via the Recovery GUI,
if that occurs consider uploading the firmware through cURL:
curl -v -i -F "firmware=@file.bin" 192.168.0.1
Signed-off-by: Mateus B. Cassiano <mbc07@live.com>
[move DEVICE_VARIANT to individual definitions]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Specifications:
* SoC: MediaTek MT7621A (880 MHz 2c/4t)
* RAM: Nanya NT5CC128M16IP-DIT (256M DDR3-1600)
* Flash: Macronix MX30LF1G18AC-TI (128M NAND)
* Eth: MediaTek MT7621A (10/100/1000 Mbps x5)
* Radio: MT7615N (2.4 GHz & 5 GHz)
4 antennae: 1 internal and 3 non-deatachable
* USB: 3.0 (x1)
* LEDs:
White (x1 logo)
Green (x6 eth + wps)
Orange (x5, hardware-bound)
* Buttons:
Reset (x1)
WPS (x1)
Everything works! Been running it for a couple weeks now and haven't had
any problems. Please let me know if you run into any.
Installation:
Flash factory image through GUI.
This might fail due to the A/B nature of this device. When flashing, OEM
firmware writes over the non-booted partition. If booted from 'A',
flashing over 'B' won't work. To get around this, you should flash the
OEM image over itself. This will then boot the router from 'B' and
allow you to flash OpenWRT without problems.
Reverting to factory firmware:
Hard-reset the router three times to force it to boot from 'B.' This is
where the stock firmware resides. To remove any traces of OpenWRT from
your router simply flash the OEM image at this point.
Signed-off-by: Santiago Rodriguez-Papa <contact@rodsan.dev>
[use v1 only, minor DTS adjustments, use LINKSYS_HWNAME and add it to
DEVICE_VARS, wrap DEVICE_PACKAGES, adjust commit message/title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Add a common definition for ELECOM WRC "GS" devices to mt7621.mk
to not repeat the same assignments five times.
To keep the naming consistent, slightly rename the DTSI and the
factory image recipe as well.
Note that elecom_wrc-1167ghbk2-s uses a slightly different build
recipe for the factory image, so we keep it separate.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: INAGAKI Hiroshi <musashino.open@gmail.com> [WRC-1750GSV]
Specifications:
SoC: MT7621AT
RAM: 128MB
Flash: 16MB NOR SPI flash
WiFi: MT7615N (2.4GHz) and MT7615N (5Ghz)
LAN: 5x1000M
Firmware layout is Uboot with extra 96 bytes in header
Base PCB is AP-MTKH7-0002
LEDs Power Green,Power Orange,Internet Green,Internet Orange
LEDs "2.4G" Green & "5G" Green connected directly to wifi module
Buttons Reset,WPS,WIFI
Flashing instructions:
Upload image via emergency recovery mode
Push and hold reset button (on the back of the device) until power led
starts flashing (about 10 secs or so) while powering the device on.
Give it ~30 seconds, to boot the recovery mode GUI
Connect your client computer to LAN1 of the device
Set your client IP address manually to 192.168.0.2 / 255.255.255.0.
Call the recovery page for the device at http://192.168.0.1
Use the provided emergency web GUI to upload and flash a new firmware to
the device. Some browsers/OS combinations are known not to work, so if
you don't see the percentage complete displayed and moving within a few
seconds, restart the procedure from scratch and try anoher one,
or try the command line way.
Alternative method using command line on Linux:
curl -v -i -F "firmware=@openwrt-xxxx-squashfs-factory.bin" 192.168.0.1
Signed-off-by: Mathieu Martin-Borret <mathieu.mb@protonmail.com>
[use of generic uimage-padhdr in image generation code]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This creates a common DTSI and shared image definition for the
relatively similar Netgear devices for mt7628 platform.
As a side effect, this raises SPI flash frequency for the R6120,
as it's expected to work there as well if it works for R6080 and
R6020.
Based on the data from the other devices, it also seems probable
the 5g MAC address for R6120 could be extracted from the caldata,
and the mtd-mac-address there could be dropped.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
There are already two very similar recipes using uimage_padhdr
in ramips target, and a third one is about to be added.
Make the recipe more generic, so redefinitions are not necessary
anymore.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Bjørn Mork <bjorn@mork.no> [Zyxel WAP6805]
This adds support for the Netgear R6020, aka Netgear AC750.
The R6020 appears to be the same hardware as the Netgear R6080,
aka Netgear AC1000, but it has a slightly different flash layout,
and no USB ports.
Specification:
SoC: MediaTek MT7628 (580 MHz)
Flash: 8 MiB
RAM: 64 MiB
Wireless: 2.4Ghz (builtin) and 5Ghz (MT7612E)
LAN speed: 10/100
LAN ports: 4
WAN speed: 10/100
WAN ports: 1
UART (57600 8N1) on PCB
MAC addresses based on vendor firmware:
LAN *:88 0x4
WAN *:89
WLAN2 *:88 0x4
WLAN5 *:8a 0x8004
The factory partition might have been corrupted beforehand. However,
the comparison of vendor firmware and OpenWrt still allowed to retrieve
a meaningful assignment that also matches the other similar devices.
Installation:
Flashing OpenWRT from stock firmware requires nmrpflash. Use an ethernet
cable to connect to LAN port 1 of the R6020, and power the R6020 off.
From the connected workstation, run
`nmrpflash -i eth0 -f openwrt-ramips-mt76x8-netgear_r6020-squashfs-factory.img`,
replacing eth0 with the appropriate interface (can be identified by
running `nmrpflash -L`). Then power on the R6020. After flashing has finished,
power cycle the R6020, and it will boot into OpenWRT. Once OpenWRT has been
installed, subsequent flashes can use the web interface and sysupgrade files.
Signed-off-by: Tim Thorpe <timfthorpe@gmail.com>
[slightly extend commit message, fix whitespaces in DTS, align From:
with Signed-off-by]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The rg21s fails to boot if the kernel is larger than about
2,376 KiB. The ra21s is virtually identical hardware.
Enabling lzma-loader resolves the issue on both the rg21s
and ra21s (see FS#3057 on the issue tracker).
Fixes: FS#3057
Signed-off-by: Furkan Alaca <furkan.alaca@queensu.ca>
Device specification:
SoC: RT5350
CPU Frequency: 360 MHz
Flash Chip: Macronix MX25L6406E (8192 KiB)
RAM: Winbond W9825G6JH-6 (32768 KiB)
5x 10/100 Mbps Ethernet (4x LAN, 1x WAN)
1x external antenna
UART (J1) header on PCB (57800 8n1)
Wireless: SoC-intergated: 2.4GHz 802.11bgn
USB: None
8x LED, 2x button
Flash instruction:
Configure PC with static IP 192.168.99.8/24 and start TFTP server.
Rename "openwrt-ramips-rt305x-zyxel_keenetic-lite-b-squashfs-sysupgrade.bin"
to "rt305x_firmware.bin" and place it in TFTP server directory.
Connect PC with one of LAN ports, press the reset button, power up
the router and keep button pressed until power LED start blinking.
Router will download file from TFTP server, write it to flash and reboot.
Signed-off-by: Sergei Burakov <senior.anonymous@ya.ru>
Adding this has been overlooked when rebasing the commit prior to
merge.
Fixes: ba0f4f0cfd ("ramips: add support for TP-Link RE500 v1")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Hardware
--------
SoC: MediaTek MT7621ST
WiFi: MediaTek MT7603
Quantenna QT3840BC
Flash: 128M NAND
RAM: 64M
LED: Dual colour red and green
BTN: Reset
WPS
Eth: 4 x 10/100/1000 connected to MT7621 internal switch
MT7621 RGMII port connected to Quantenna module
GPIO: Power/reset of Quantenna module
Quantenna module
----------------
The Quantenna QT3840BC (or QV840) is a separate SoC running
another Linux installation. It is mounted on a wide mini-PCIe
form factor module, but is connected to the RGMII port of
the MT7621. It loads both a second uboot stage and an os
image from the MT7621 using tftp. The module is configured
using Quantenna specific RPC calls over IP, using 802.1q
over the RGMII link to support multiple SSIDs.
There is no support for using this module as a WiFi device
in OpenWrt. A package with basic firmware and management
tools is being prepared.
Serial ports
------------
Two serial ports with headers:
RRJ1 - 115200 8N1 - Connected to the Quantenna console
J1 - 57600 8N1 - Connected to the MT7621 console
Both share pinout with many other Zyxel/Mitrastar devices:
1 - NC (VDD)
2 - TX
3 - RX
4 - NC (no pin)
5 - GND
Dual system partitions
----------------------
The vendor firmware and boot loader use a dual partition
scheme storing a counter in the header of each partition. The
partition with the highest number will be selected for boot.
OpenWrt does not support this scheme and will always use the
first OS partition. It will reset both counters to zero the
first time sysupgrade is run, making sure the first partition
is selected by the boot loader.
Installation from vendor firmware
---------------------------------
1. Run a DHCP server. The WAP6805 is configured as a client device
and does not have a default static IP address. Make a note of
which address it is assigned
2. tftp the OpenWrt initramfs-kernel.bin image to this address.
Wait for the WAP6805 to reboot.
3. ssh to the OpenWrt initramfs system on 192.168.1.1. Make a
backup of all mtd partitions now. The last used OEM image is
still present in either "Kernel" or "Kernel2" at this point,
and can be restored later if you save a copy.
4. sysupgrade to the OpenWrt sysupgrade.bin image.
Installation from U-Boot
------------------------
This requires serial console access
1. Copy the OpenWrt initramfs-kernel.bin image as "ras.bin" to
your tftp server directory. Configure the server address as
192.168.0.33/24
2. Hit ESC when the message "Hit ESC key to stop autoboot"
appears
3. Type "ATGU" + Enter, and then "2" immediately after pressing enter.
4. Answer Y to the question "Erase Linux in Flash then burn new
one. Are you sure?", and answer the address/filename questions.
Defaults:
Input device IP (192.168.0.2)
Input server IP (192.168.0.33)
Input Linux Kernel filename ("ras.bin")
5. Wait until after you see the message "Done!" and power cycle
the device. It will hang after flashing.
6. Continue with step 3 and 4 from the vendor firmware procedure.
Notes on the WAP6805 U-Boot
---------------------------
The bootloader has been modified with both ZyXELs zyloader and the
device specific dual partition scheme. These changes appear to have
broken a few things. The zyloader shell claims to support a number
of ZyXEL AT commands, but not all of them work. The image selection
scheme is unreliable and inconsistent. A limited U-Boot menu is
available - and used by the above U-Boot install procedure. But
direct booting into an uploaded image does not work, neither with
ram nor with flash. Flashing works, but requires a hard reset after
it is finished.
Reverting to OEM firmware
-------------------------
The OEM firmware can be restored by using mtd write from OpenWrt,
flashing it to the "Kernel" partition. E.g.
ssh root@192.168.1.1 "mtd -r -e Kernel write - Kernel" < oem.bin
OEM firmwares for the WAP6805 are not avaible for public download,
so a backup of the original installation is required. See above.
Alternatively, firmware for the WAP6806 (Armor X1) may be used. This
is exactly the same hardware. But the branding features do obviously
differ.
LED controller
--------------
Hardware implementation is unknown. The dual-color LED is controlled
by 3 GPIOs:
4: red
7: blinking green
13: green
Enabling both red and green makes the LED appear yellow.
The boot loader enables hardware blinking, causing the green LED to blink
slowly on power-on, until the OpenWrt boot mode starts a faster software
blink.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
[fix alphabetic sorting for image build statement]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The Xiaomi Mi Router AC2100 is a *black* cylindrical router that shares many
characteristics (apart from its looks and the GPIO ports) with the 6-antenna
*white* "Xiaomi Redmi Router AC2100"
See the visual comparison of the two routers here:
https://github.com/emirefek/openwrt-R2100/raw/imgcdn/rm2100-r2100.jpg
Specification of R2100:
- CPU: MediaTek MT7621A
- RAM: 128 MB DDR3
- FLASH: 128 MB ESMT NAND
- WIFI: 2x2 802.11bgn (MT7603)
- WIFI: 4x4 802.11ac (MT7615)
- ETH: 3xLAN+1xWAN 1000base-T
- LED: Power, WAN in Yellow and Blue
- UART: On board (Don't know where is should be confirmed by anybody else)
- Modified u-boot
Hacking of official firmware process is same at both RM2100 and R2100.
Thanks to @namidairo
Here is the detailed guide Hack: https://github.com/impulse/ac2100-openwrt-guide
Guide is written for MacOS but it will work at linux.
needed packages: python3(with scapy), netcat, http server, telnet client
1. Run PPPoE&exploit to get nc and wget busybox, get telnet and wget firmware
2. mtd write openwrt-ramips-mt7621-xiaomi_mi-router-ac2100-kernel1.bin kernel1
3. nvram set uart_en=1
4. nvram set bootdelay=5
5. nvram set flag_try_sys1_failed=1
6. nvram commit
7. mtd -r write openwrt-ramips-mt7621-xiaomi_mi-router-ac2100-rootfs0.bin rootfs0
other than these I specified in here. Everything is same with:
f3792690c4
Thanks for all community and especially for this device:
@Ilyas @scp07 @namidairo @Percy @thorsten97 @impulse (names@forum.openwrt.com)
MAC Locations:
WAN *:b5 = factory 0xe006
LAN *:b6 = factory 0xe000
WIFI 5ghz *:b8 = factory 0x8004
WIFI 2.4ghz *:b7 = factory 0x0004
Signed-off-by: Emir Efe Kucuk <emirefek@gmail.com>
[refactored common image bits into Device/xiaomi-ac2100, fixed From:]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Hardware
--------
SoC: Mediatek MT7621AT (880 MHz, 2 cores 4 threads)
RAM: 128MB
FLASH: 16MB NOR (Macronix MX25L12805D)
ETH: 1x 10/100/1000 Mbps Ethernet (MT7530)
WIFI:
- 2.4GHz: 1x MT7615 (4x4:4)
- 5GHz: 1x MT7615 (4x4:4)
- 4 antennas: 2 external detachable and 2 internal
BTN:
- 1x Reset button
- 1x WPS button
LEDS:
- 1x Green led (Power)
- 1x Green-Amber-Red led (Wifi)
UART:
- 57600-8-N-1
Everything works correctly.
Installation
------------
Flash the factory image directly from OEM web interface.
(You can login using these credentials: admin/1234)
Restore OEM Firmware
--------------------
Flash the OEM "bin" firmware directly from LUCI.
The firmware is downloadable from the OEM web page.
Warning: Remember to not keep settings!
Warning2: Remember to force the flash.
Restoring procedure tested with RE23_1.08.bin
MAC addresses
-------------
factory 0x4 *:24
factory 0x8004 *:25
Cimage 0x07 *:24
Cimage 0x0D *:24
Cimage 0x13 *:24
Cimage 0x19 *:25
No other addresses were found in factory partition.
Since the label contains both the 2.4GHz and 5GHz mac address I decided
to set the 5GHz one as label-mac-device. Moreover it also corresponds
to the lan mac address.
Notes
-----
The wifi led in the OEM firmware changes colour depending on the signal
strength. This can be done in OpenWrt but just for one interface.
So for now will not be any default action for this led.
If you want to open the case, pay attention to the antenna placed on
the bottom part of the front cover.
The wire is a bit short and it breaks easily. (I broke it)
Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
[fix two typos and add extended MAC address section to commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This device uses the same hardware as RE650 v1 which got supported in
8c51dde.
Hardware specification:
- SoC 880 MHz - MediaTek MT7621AT
- 128 MB of DDR3 RAM
- 16 MB - Winbond 25Q128FVSG
- 4T4R 2.4 GHz - MediaTek MT7615E
- 4T4R 5 GHz - MediaTek MT7615E
- 1x 1 Gbps Ethernet - MT7621AT integrated
- 7x LEDs (Power, 2G, 5G, WPS(x2), Lan(x2))
- 4x buttons (Reset, Power, WPS, LED)
- UART header (J1) - 2:GND, 3:RX, 4:TX
Serial console @ 57600,8n1
Flash instructions:
Upload
openwrt-ramips-mt7621-tplink_re500-v1-squashfs-factory.bin
from the RE500 web interface.
TFTP recovery to stock firmware:
Unfortunately, I can't find an easy way to recover the RE
without opening the device and using modified binaries. The
TFTP upload will only work if selected from u-boot, which
means you have to open the device and attach to the serial
console. The TFTP update procedure does *not* accept the
published vendor firmware binaries. However, it allows to
flash kernel + rootfs binaries, and this works if you have
a backup of the original contents of the flash. It's probably
possible to create special image out of the vendor binaries
and use that as recovery image.
Signed-off-by: Christoph Krapp <achterin@googlemail.com>
[remove dts-v1 in DTSI, do not touch WiFi LEDs for RE650, keep
state_default in DTS files, fix label-mac-device, use lower case
for WiFi LEDs]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
TP-Link RE220 v2 is a wireless range extender with Ethernet and 2.4G and 5G
WiFi with internal antennas. It's based on MediaTek MT7628AN+MT7610EN.
This port of OpenWRT leverages work done by Andreas Böhler <dev@aboehler.at>
for the TP-Link RE200 v2 as both devices share the same SoC, flash layout
and GPIO pinout.
Specifications
MediaTek MT7628AN (580 Mhz)
64 MB of RAM
8 MB of FLASH
2T2R 2.4 GHz and 1T1R 5 GHz
1x 10/100 Mbps Ethernet
UART header on PCB (57600 8n1)
8x LED (GPIO-controlled), 2x button
There are 2.4G and 5G LEDs in red and green which are controlled separately.
Web Interface Installation
It is possible to upgrade to OpenWrt via the web interface. Simply flash
the -factory.bin from OEM. In contrast to a stock firmware, this will not
overwrite U-Boot.
Signed-off-by: Rowan Border <rowanjborder@gmail.com>
This package allows to read battery status information and control the
power state of the RAVPower RP-WD009 power management IC.
Signed-off-by: David Bauer <mail@david-bauer.net>
The RAVPower RP-WD009 is a batter-powered pocket sized router with SD
card lot and USB port.
Hardware
--------
CPU: MediaTek MT7628AN
RAM: 64M DDR2
FLASH: 16M GigaDevices SPI-NOR
WLAN: MediaTek MT7628AN 2T2R b/g/n
MediaTek MT7610E 1T1R n/ac
ETH: 1x FastEthernet
SD: SD Card slot
USB: USB 2.0
Custom PMIC on the I2C bus (address 0x0a).
Installation
------------
1. Press and hold down the reset button.
2. Power up the Device. Keep pressing the reset button for 10
more seconds until the Globe LED lights up.
3. Attach your Computer to the Ethernet port. Assign yourself the
address 10.10.10.1/24.
4. Access the recovery page at 10.10.10.128 and upload the OpenWrt
factory image.
5. The flashing will take around 1 minute. The device will reboot
automatically into OpenWrt.
Signed-off-by: David Bauer <mail@david-bauer.net>
This commit adds support for the Wavlink WL-WN577A2 (black case) dual-band
wall-plug wireless router. In Germany this device is sold under the brand
name Maginon WL-755 (white case):
Device specifications:
- CPU: MediaTek MT7628AN (580MHz)
- Flash: 8MB
- RAM: 64MB
- Bootloader: U-Boot
- Ethernet: 2x 10/100 Mbps (Ralink RT3050)
- 2.4 GHz: 802.11b/g/n SoC
- 5 GHz: 802.11a/n/ac MT7610E
- Antennas: internal
- 4 green LEDs: 1 programmable (WPS) + LAN, WAN, POWER
- Buttons: Reset, WPS
- Small sliding power switch
Flashing instructions (U-boot):
- Configure a TFTP server on your PC/Laptop and set its IP
to 192.168.10.100
- Rename the OpenWrt image to firmware.bin and place it in the
root folder of the TFTP server
- Power off (using the small sliding power switch on the left
side) the device and connect an ethernet cable from its LAN
or WAN port to your PC/Laptop
- Press the WPS button (and keep it pressed)
- Power on the device (using the small power switch)
- After a few seconds, when the WAN/LAN LED stops blinking
very fast, release the WPS button
- Flashing OpenWrt takes less than a minute, system will
reboot automatically
- After reboot the WPS LED will indicate the current OpenWrt
running status
Signed-off-by: Lars Wessels <software@bytebox.org>
[removed unused labels - fix whitespace errors - wrap commit message]
Signed-off-by: David Bauer <mail@david-bauer.net>
The WAC124 hardware appears to be identical to R6260/R6350/R6850.
SoC: MediaTek MT7621AT
RAM: 128M DDR3
FLASH: 128M NAND (Macronix MX30LF1G18AC)
WiFI: MediaTek MT7603 bgn 2T2R
MediaTek MT7615 nac 4T4R
ETH: SoC Integrated Gigabit Switch (1x WAN, 4x LAN)
USB: 1x USB 2.0
BTN: Reset, WPS
LED: Power, Internet, WiFi, USB (all green)
Installation:
The factory image can be flashed from the stock firmware web interface
or using nmrpflash. With nmrpflash it is also possible to revert to
stock firmware.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
This adds support for the Netgear R6080, aka Netgear AC1000.
The R6080 has almost the same hardware as the Netgear R6120,
aka Netgear AC1200, but it lacks the USB port, has only 8 MiB flash and
uses a different SERCOMM_HWID.
Specification:
SoC: MediaTek MT7628 (580 MHz)
Flash: 8 MiB
RAM: 64 MiB
Wireless: 2.4Ghz (builtin) and 5Ghz (MT7612E)
LAN speed: 10/100
LAN ports: 4
WAN speed: 10/100
WAN ports: 1
UART (57600 8N1) on PCB
Installation:
Flashing OpenWRT from stock firmware requires nmrpflash. Use an ethernet
cable to connect to LAN port 1 of the R6080, and power the R6080 off.
From the connected workstation, run
`nmrpflash -i eth0 -f openwrt-ramips-mt76x8-netgear_r6080-squashfs-factory.img`,
replacing eth0 with the appropriate interface (can be identified by
running `nmrpflash -L`). Then power on the R6080. After flashing has finished,
power cycle the R6080, and it will boot into OpenWRT. Once OpenWRT has been
installed, subsequent flashes can use the web interface and sysupgrade files.
Signed-off-by: Alex Lewontin <alex.c.lewontin@gmail.com>
[rebase and adjust for 5.4]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This commit performs minor janitorial work to clean up some code
formatting for the Netgear R6120.
Signed-off-by: Alex Lewontin <alex.c.lewontin@gmail.com>
NETGEAR WAC104 is an AP based on castrated R6220, without WAN
port and USB.
SoC: MediaTek MT7621ST
RAM: 128M DDR3
FLASH: 128M NAND
WiFi: MediaTek MT7612EN an+ac
MediaTek MT7603EN bgn
ETH: MediaTek MT7621ST (4x LAN)
BTN: 1x Connect (WPS), 1x WLAN, 1x Reset
LED: 7x (3x GPIO controlled)
Installation:
Login to netgear webinterface and flash factory.img
Back to stock:
Use nmrpflash to revert stock image.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Specifications:
* SoC: MT7620A
* CPU: 580 MHz
* RAM: 64 MB DDR
* Flash: 8MB NOR SPI flash
* WiFi: MT7612E (5GHz) and builtin MT7620A (2.4GHz)
* LAN: 1x100M
The device is identical to the EX6130 except
for the mains socket and the hardware ID.
Installation:
The -factory images can be flashed from the
device's web interface or via nmrpflash.
Notes:
MAC addresses were set up based on the EX6130 setup.
This is based on prior work of Adam Serbinski and Mathias Buchwald.
Tested by Mathias Buchwald.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
ZyXEL Keenetic has a USB port. Thus, DWC2 USB controller driver should
be in the default image for this device.
Fixes: a7cbf59e0e ("ramips: add new device ZyXEL Keenetic as kn")
Signed-off-by: Alexey Dobrovolsky <dobrovolskiy.alexey@gmail.com>
[fixed whitespace issue]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Specifications:
* MediaTek MT7620A (580 Mhz)
* 8 MB of FLASH
* 64 MB of RAM
* 2.4Ghz and 5.0Ghz radios
* 5x 10/100 Mbps Ethernet (1 WAN and 4 LAN)
* UART header on PCB (57600 8n1)
* Green/Orange Power LEDs illuminating a Power-Button Lens
* Green/Orange Internet LEDs GPIO controlled illuminating a Globe/Internet Lens
* 3x button - wps, power and reset
* U-boot bootloader
Installation:
The sysupgrade.bin image is reported to be OEM web flashed with an ncc_att_hwid
appended. ncc_att_hwid is a 32bit binary in the GPL Source download for either
the TEW-810DR or DIR-810L and is located at
source/user/wolf/cameo/ncc/hostTools.
The invocation is: ncc_att_hwid -f tew-810dr-squashfs-factory.bin -a -m "TEW-810DR" -H "1.0R" -r "WW" -c "1.0"
This may need to be altered if your hardware version is "1.1R".
The image can also be directly flashed via serial tftp:
1. Load *.sysupgrade.bin to your tftp server directory and rename for
convenience.
2. Set a static ip 192.168.10.100.
3. NIC cable to a lan port.
4. Serial connection parameters 57600,8N1
5. Power on the TEW-810 and press 4 for a u-boot command line prompt.
6. Verify IP's with U-Boot command "printenv".
7. Adjust tftp settings if needed per the tftp documentation
8. Boot the tftp image to test the build.
9. If the image loads, reset your server ip to 192.168.1.10 and restart network.
10. Log in to Luci, 192.168.1.1, and flash the *sysupgrade.bin image.
Notes:
The only valid MAC address is found in 0x28 of the factory partition.
Other typical offsets/caldata only contain example data: 00:11:22:00:0f:xx
Signed-off-by: J. Scott Heppler <shep971@centurylink.net>
[remove "link rx tx" in 01_leds, format and extend commit message,
fix DTS led node names]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Specifications:
- MT7628NN @ 580 MHz
- 32 MB RAM
- 8 MB Flash
- 5x 10/100 Mbps Ethernet (built-in switch)
- 2.4 GHz WLAN
- 2x external, non-detachable antennas (1x for RT-N10P V3)
Flash instructions:
1. Set PC network interface to 192.168.1.75/24.
2. Connect PC to the router via LAN.
3. Turn router off, press and hold reset button, then turn it on.
4. Keep the button pressed till power led starts to blink.
5. Upload the firmware file via TFTP. (Any filename is accepted.)
6. Wait until the router reboots.
Signed-off-by: Ernst Spielmann <endspiel@disroot.org>
[fix node/property name for state_default]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Specification:
- CPU: MediaTek MT7621A
- RAM: 128 MB DDR3
- FLASH: 128 MB ESMT NAND
- WIFI: 2x2 802.11bgn (MT7603)
- WIFI: 4x4 802.11ac (MT7615)
- ETH: 3xLAN+1xWAN 1000base-T
- LED: Power, WAN, in Amber and White
- UART: On board near ethernet, opposite side from power
- Modified u-boot
Installation:
1. Run linked exploit to get shell, startup telnet and wget the files over
2. mtd write openwrt-ramips-mt7621-xiaomi_rm2100-squashfs-kernel1.bin kernel1
3. nvram set uart_en=1
4. nvram set bootdelay=5
5. nvram set flag_try_sys1_failed=1
6. nvram commit
7. mtd -r write openwrt-ramips-mt7621-xiaomi_rm2100-squashfs-rootfs0.bin rootfs0
Restore to stock:
1. Setup PXE and TFTP server serving stock firmware image
(See dhcp-boot option of dnsmasq)
2. Hold reset button down before powering on and wait for flashing amber led
3. Release reset button
4. Wait until status led changes from flashing amber to white
Notes:
This device has dual kernel and rootfs slots like other Xiaomi devices currently
supported (mir3g, etc.) thus, we use the second slot and overwrite the first
rootfs onwards in order to get more space.
Exploit and detailed instructions:
https://openwrt.org/toh/xiaomi/xiaomi_redmi_router_ac2100
An implementation of CVE-2020-8597 against stock firmware version 1.0.14
This requires a computer with ethernet plugged into the wan port and an active
PPPoE session, and if successful will open a reverse shell to 192.168.31.177
on port 31337.
As this shell is somewhat unreliable and likely to be killed in a random amount
of time, it is recommended to wget a static compiled busybox binary onto the
device and start telnetd with it.
The stock telnetd and dropbear unfortunately appear inoperable.
(Disabled on release versions of stock firmware likely)
Ie. wget https://yourip/busybox-mipsel -O /tmp/busybox
chmod a+x /tmp/busybox
/tmp/busybox telnetd -l /bin/sh
Tested-by: David Martinez <bonkilla@gmail.com>
Signed-off-by: Richard Huynh <voxlympha@gmail.com>
This is additional fix of c998ae7f0e.
The sysupgrade image of I-O DATA MT7621 devices manufactured by MSTC
(MitraStar Technology Corp.) faced to the booting issue. This was caused
by imcomplete extraction of large kernel image by U-Boot, and this issue
is occurred in initramfs image after fixing of sysupgrade image.
So, use lzma-loader for initramfs image to fix the issue.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Co-developed-by: Yanase Yuki <dev@zpc.sakura.ne.jp>
Signed-off-by: Yanase Yuki <dev@zpc.sakura.ne.jp>
Tested-by: Yanase Yuki <dev@zpc.sakura.ne.jp> [wn-ax2033gr]
The version inside the compat file determines, if a firmware supports
a specific device. I have not yet fully understood, how this is checked,
but it only seems to indicate which devices are supported by a specific
version of the combined vendor firmware. Devices assume that subsequent
versions, starting with the version that initially added support for a
specific device, are always compatible.
The first compat version that added support for the EP-R6 was '21001:7',
but OpenWrt did use '21001:6' before. This is why the factory image could
not be flashed using the vendor software, but only using TFTP.
The compat version has been bumped by the vendor a few times, but more
devices have been added since (e.g. ER-10X). Because OpenWrt currently
only supports the ER-X, ER-X-SFP and EP-R6, the compat version is
incremented to the version that first supported the EP-R6, which is
'21001:7'.
This allows the factory image to be flashed on EP-R6 without TFTP.
Signed-off-by: Fabian Bläse <fabian@blaese.de>
The Linksys EA7500 v2 is advertised as AC1900, but its internal
hardware is AC2600 capable.
Hardware
--------
SoC: Mediatek MT7621AT (880 MHz, 2 cores 4 threads)
RAM: 256M (Nanya NT5CC128M16IP-DI)
FLASH: 128MB NAND (Macronix MX30LF1G18AC-TI)
ETH: 5x 10/100/1000 Mbps Ethernet (MT7530)
WIFI:
- 2.4GHz: 1x MT7615N (4x4:4)
- 5GHz: 1x MT7615N (4x4:4)
- 4 antennas: 3 external detachable antennas and 1 internal
USB:
- 1x USB 3.0
- 1x USB 2.0
BTN:
- 1x Reset button
- 1x WPS button
LEDS:
- 1x White led (Power)
- 6x Green leds (link lan1-lan4, link wan, wps)
- 5x Orange leds (act lan1-lan4, act wan) (working but unmodifiable)
Everything works correctly.
Installation
------------
The “factory” openwrt image can be flashed directly from OEM stock
firmware. After the flash the router will reboot automatically.
However, due to the dual boot system, the first installation could fail
(if you want to know why, read the footnotes).
If the flash succeed and you can reach OpenWrt through the web
interface or ssh, you are done.
Otherwise the router will try to boot 3 times and then will
automatically boot the OEM firmware (don’t turn off the router.
Simply wait and try to reach the router through the web interface
every now and then, it will take few minutes).
After this, you should be back in the OEM firmware.
Now you have to flash the OEM Firmware over itself using the OEM web
interface (I tested it using the FW_EA7500v2_2.0.8.194281_prod.img
downloaded from the Linksys website).
When the router reboots flash the “factory” OpenWrt image and this
time it should work.
After the OpenWrt installation you have to use the sysupgrade image
for future updates.
Restore OEM Firmware
--------------------
After the OpenWrt flash, the OEM firmware is still stored in the
second partition thanks to the dual boot system.
You can switch from OpenWrt to OEM firmware and vice-versa failing
the boot 3 times in a row:
1) power on the router
2) wait 15 seconds
3) power off the router
4) repeat steps 1-2-3 twice more.
5) power on the router and you should be in the “other” firmware
If you want to completely remove OpenWrt from your router, switch to
the OEM firmware and then flash OEM firmware from the web interface
as a normal update.
This procedure will overwrite the OpenWrt partition.
Footnotes
---------
The Linksys EA7500-v2 has a dual boot system to avoid bricks.
This system works using 2 pair of partitions:
1) "kernel" and "rootfs"
2) "alt_kernel" and "alt_rootfs".
After 3 failed boot attempts, the bootloader tries to boot the other
pair of partitions and so on.
This system is managed by the bootloader, which writes a bootcount in
the s_env partition, and if successfully booted, the system add a
"zero-bootcount" after the previous value.
A system update performed from OEM firmware, writes the firmware on the
other pair of partitions and sets the bootloader to boot the new pair
of partitions editing the “boot_part” variable in the bootloader vars.
Effectively it's a quick and safe system to switch the selected boot
partition.
Another way to switch the boot partition is:
1) power on the router
2) wait 15 seconds
3) power off the router
4) repeat steps 1-2-3 twice more.
5) power on the router and you should be in the “other” firmware
In this OpenWrt port, this dual boot system is partially working
because the bootloader sets the right rootfs partition in the cmdline
but unfortunately OpenWrt for ramips platform overwrites the cmdline
so is not possible to detect the right rootfs partition.
Because all of this, I preferred to simply use the first pair of
partitions and set read-only the other pair.
However this solution is not optimal because is not possible to know
without opening the case which is the current booted partition.
Let’s take for example a router booting the OEM firmware from the first
pair of partitions. If we flash the OpenWrt image, it will be written
on the second pair. In this situation the router will bootloop 3 times
and then will automatically come back to the first pair of partitions
containg the OEM firmware.
In this situation, to flash OpenWrt correctly is necessary to switch
the booting partition, flashing again the OEM firmware over itself.
At this point the OEM firmware is on both pair of partitions but the
current booted pair is the second one.
Now, flashing the OpenWrt factory image will write the firmware on
the first pair and then will boot correctly.
If this limitation in the ramips platform about the cmdline will be
fixed, the dual boot system can also be implemented in OpenWrt with
almost no effort.
Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
Co-Developed-by: Jackson Lim <jackcolentern@gmail.com>
Signed-off-by: Jackson Lim <jackcolentern@gmail.com>
netis WF2770 is a 2.4/5GHz band AC750 router, based on MediaTek MT7620A.
Specifications:
- SoC: MT7620A
- RAM: DDR2 64MB
- Flash: SPI NOR 16MB
- WiFi:
- 2.4GHz: SoC internal
- 5GHz: MT7610EN
- Ethernet: 5x 10/100/1000Mbps
- Switch: MT7530BU
- UART:
- J2: 3.3V, RX, TX, GND (3.3V is the square pad) / 57600 8N1
MAC addresses in factory partition:
0x0004: LAN, WiFi 2.4GHz (label_mac-6)
0x0028: not used (label_mac-1)
0x002e: WAN (label_mac)
0x8004: WiFi 5GHz (label_mac+2)
Installation via web interface:
1. Flash **initramfs** image through the stock web interface.
2. Boot into OpenWrt and perform sysupgrade with sysupgrade image.
Revert to stock firmware:
1. Perform sysupgrade with stock image.
Reviewed-by: Pawel Dembicki <paweldembicki@gmail.com>
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Specification:
- CPU: MTK MT7620A
- RAM: 64MB
- ROM: 16MB SPI Flash Macronix MX25L12835E
- WiFi1: MediaTek MT7620A
- WiFi2: MediaTek MT7612E
- Button: reset, wps
- LED: 9 LEDs:Power, WiFi 2.4G,WiFi 5G, USB, LAN1, LAN2, LAN3, LAN4, WAN
- Ethernet: 5 ports, 4 LAN + 1 WAN
- Other: 1x UART 1x USB2.0
Installation:
Update using ASUS Firmware Restoration Tool:
1. Download the ASUS Firmware Restoration Tool but don't open it yet
2. Unplug your computer from the router
3. Put the router into Rescue Mode by: turning the power off, using a pin
to press and hold the reset button, then turning the router back on while
keeping the reset button pressed for ~5 secs until the power LED starts
flashing slowly (which indicates the router has entered Rescue Mode)
4. Important (if you don't do this next step the Asus Firmware
Restoration Tool will wrongly assume that the router is not in Rescue Mode
and will refuse to flash it): go to the Windows Control Panel and
temporarily disable ALL other network adapters except the one you will use
to connect your computer to the router
5. For the single adapter you left enabled, temporarily give it the
static IP 192.168.1.10 and the subnet mask 255.255.255.0
6. Connect a LAN cable between your computer (make sure to use the
Ethernet port of the adapter you've just set up) and port 1 of the router
(not the router's WAN port)
7. Rename sysupgrade.bin to factory.trx
8. Open the Asus Firmware Restoration Tool, locate factory.trx and click
upload (if Windows shows a compatibility prompt, confirm that the tool worked fine)
9. Flashing and reboot is finished when the power LED stops blinking and
stays on
MAC assignment based on vendor firmware:
2g 0x4 label
5g 0x8004 label +4
lan 0x22 label +4
wan 0x28 label
Signed-off-by: Zhijun You <hujy652@gmail.com>
[rebased due to DTSI patch, minor commit message adjustments, fix
label MAC address (lan->wan), do spi frequency increase separately]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The BL-W1200 Wireless Router is based on the MT7620A SoC.
Specification:
- MediaTek MT7620A (580 Mhz)
- 64 MB of RAM
- 8 MB of FLASH
- 1x 802.11bgn radio
- 1x 802.11ac radio (MT7612E)
- 5x 10/100/1000 Mbps Ethernet (MT7530)
- 2x external, non-detachable antennas (Wifi 2.4G/5G)
- 1x USB 2.0
- UART (R2) on PCB (57600 8n1)
- 9x LED (1 GPIO controlled), 1x button
- u-Boot bootloader
Known issues:
- No status LED. Used WPS LED during boot/failsafe/sysupgrade.
Installation:
1. Apply initramfs image via factory web-gui.
2. Install sysupgrade image.
How to revert to OEM firmware:
- sysupgrade -n -F stock_firmware.bin
Reviewed-by: Sungbo Eo <mans0n@gorani.run>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
- use tab indent in image build recipes for consistency
- harmonize line wrapping
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[use different line wrapping for one recipe]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
In rt3883 subtarget, several devices add swconfig to their DEVICE_PACKAGES.
This is redundant as the package is already provided via DEFAULT_PACKAGES.
Remove the redundant inclusions.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
These definitions are not required since swconfig is selected for
the target anyway and kmod-swconfig is pulled as dependency by
kmod-switch-rtl8366rb.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Three of the I-O DATA devices with NAND flash share a lot of
variables. Create a common definition for them to reduce duplicate
code.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The official sysupgrade images for I-O DATA devices manufactured by
MSTC (MitraStar Technology Corp.) cannot be booted normally and the
kernel panics after switching to kernel 5.4.
This commit fixes the issue by using lzma-loader.
Note:
These devices use Z-LOADER to read the kernel from NAND flash and boot
it. Z-LOADER cannot load and start plain lzma-loader, so additional
lzma-compression is needed.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Co-developed-by: Yanase Yuki <dev@zpc.sakura.ne.jp>
Signed-off-by: Yanase Yuki <dev@zpc.sakura.ne.jp>
Tested-by: Yanase Yuki <dev@zpc.sakura.ne.jp> [wn-ax2033gr]
In several Japanese routers with MT7621 SoC, the official sysupgrade
image cannot be booted properly after switching to kernel 5.4.
This commit fixes the issue by using lzma-loader.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
This device has trouble extracting big kernel from flash,
and supports LZMA compressed kernels only.
Using OpenWrt kernel loader saves us 64 KB compared to the dictionary
size limiting workaround.
Factory image sizes (commit: 5f126c541a) with "CONFIG_ALL_KMODS=y":
- original ("-d23", default): 4784188 bytes, LZMA ERROR 1
- with "-d19": 4915260, LZMA ERROR 1
- with "-d18": 4915260, diff to original: +128 KB
- with "-d17": 4980796, diff to original: +192 KB
- with this patch: 4849724, diff to original: +64 KB
To save some CPU cycle, use minimal compression ("-a0") for the LZMA
compressed uImage.
The most robust solution would use a different loader,
which reads the compressed kernel directly from the flash.
See the thread at [0] for more details!
[0] http://lists.infradead.org/pipermail/openwrt-devel/2020-April/022926.html
Signed-off-by: Szabolcs Hubai <szab.hu@gmail.com>
Tested-by: Stijn Segers <foss@volatilesystems.org>
[fixed identation]
Signed-off-by: David Bauer <mail@david-bauer.net>
kmod-usb-dwc2 and kmod-usb-ledtrig-usbport are not target default packages, and
Belkin F7C027 does not have a USB port anyway. Just drop it.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Currently SUPPORTED_DEVICES only contains the old device string. Fix it by
removing the first assignment.
Fixes: c2334ad60d ("ramips/mt76x8: Synchronize Makefiles with DTS compatible")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Netgear R7200 is another clone of Netgear R6700v2, introduced in:
6e80df5 ("ramips: add support for NETGEAR R6700v2/AC2400")
Reported-by: Joel Pinsker, github user @joelp64
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
mt7621 overrides KERNEL_DTB to limit dictionary size, which isn't needed
for our lzma loader.
This saves 15KB on mt7621 devices using uimage-lzma-loader.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Increase kernel partition because 2M is insufficient for 5.4
Because the partition changes, previous version of OpenWrt cannot upgrade
to this version, and requires a new installation
Recovery to stock instruction:
1. Download stock firmware at
http://ur.ikcd.net/HC5962-sysupgrade-20171221-b00a04d1.bin
2. Power off the router
3. Press and hold the reset button for 4~6 sec while power it back on
4. Connect a PC to router's LAN
5. Visit http://192.168.2.1 and upload the firmware
Then repeat the instruction in edae3479e6 to install OpenWrt
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
ubnt er-x/xiaomi/netgear sercomm devices are known to have troble
extracting a big kernel from flash and has support for uncompressed
uimage
This commit uses uncompressed uimage with lzma-loader for these devices
to fix boot issue.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Some devices have bootloaders with broken lzma code resulting in failed
decompression or corrupted kernel code.
This image recipe allows to sacrifice 5KB for OpenWrt LZMA loader and
take over the task of decompress kernel.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Loader platform is a per-soc variable instead of a per-device one.
Determine corresponding loader platform at the beginning of image
Makefile.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
default initramfs for 5.4 kernel is larger than 4M, causing build error
for oversized initramfs image.
disable these images because we have no mechanism for ignoring initramfs
errors and the squashfs image will be larger than initramfs anyway.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
The "proper" vendor prefix for Ubiquiti is "ubnt", this is used in
all targets except ramips and also recommended by the kernel.
This patch adjusts the various board/image/device name variables
accordingly. Since we touch it anyway, this also adds the space
in "EdgeRouter X" as a hyphen to those variables to really make
them consistent with the model name.
While at it, create a real shared definition for the devices in
image/mt7621.mk instead of deriving one device from another.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
I-O DATA WN-AX2033GR is roughly the same as I-O DATA
WN-AX1167GR2. The difference is Wi-Fi feature.
Specification
=============
- SoC: MediaTek MT7621A
- RAM: DDR3 128 MiB
- Flash Memory: NAND 128 MiB (Spansion S34ML01G200TF100)
- Wi-Fi: MediaTek MT7603E
- Wi-Fi: MediaTek MT7615
- Ethernet: 5x 10 Mbps / 100 Mbps / 1000 Mbps (1x WAN, 4x LAN)
- LED: 2x green LED
- Input: 2x tactile switch, 1x slide switch
- Serial console: 57600bps, PCB through hole J5 (Vcc, TX, RX, NC, GND)
- Power: DC 12V
This device only supports channel 1-13 and 36-140.
Thus, narrower frequency limits compared to other devices are required
for limiting wi-fi frequency correctly.
Without this, non-supported frequencies are activated.
Flash instructions
==================
1. Open the router management page (192.168.0.1).
2. Update router firmware using "initramfs-kernel.bin".
3. After updating, run sysupgrade with "sysupgrade.bin".
Recovery instructions
=====================
WN-AX2033GR contains Zyxel Z-LOADER
1. Setup TFTP server (IP address: 10.10.10.3).
2. Put official firmware into TFTP server directory (distribution site:
https://www.iodata.jp/lib/software/w/2068.htm)
3. Connect WX-AX2033GR Ethernet port and computer that runs TFTP server.
4. Connect to serial console.
5. Interrupt booting by Esc key.
6. Flash firmware using "ATNR 1,[firmware filename]" command.
Signed-off-by: Yanase Yuki <dev@zpc.sakura.ne.jp>
[adjust for kernel 5.4, add recovery instructions/frequency comment]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
ZyXEL Keenetic has 8MB flash, but OpenWrt uses only 4MB.
This commit fixes the problem.
WikiDevi page [1] says that ZyXEL Keenetic has FLA1: 8 MiB, there is
an article with specs [2] (in Russian).
[1] https://wikidevi.wi-cat.ru/ZyXEL_Keenetic
[2] https://3dnews.ru/608774/page-2.html
Fixes: FS#2487
Fixes: a7cbf59e0e ("ramips: add new device ZyXEL Keenetic as kn")
Signed-off-by: Alexey Dobrovolsky <dobrovolskiy.alexey@gmail.com>
So far, image/device/board names for Mikrotik devices in mt7621 have
been used quite inconsistently.
This patch harmonizes the naming scheme by applying the same style
as used lately in ath79, i.e. using "RouterBOARD" as separate word
in the model name (instead of RB prefix for the number) and deriving
the board/device name from that (= make lower case and replace spaces
by hyphens).
This style has already been used for most the model/DEVICE_MODEL
variables in mt7621, so this is essentially just adjusting the remaining
variables to that.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Buffalo WSR-2533DHPL is a 2.4/5 GHz band 11ac router, based on MediaTek
MT7621A.
Specification:
- SoC : MediaTek MT7621A
- RAM : DDR3 128 MiB
- Flash : SPI-NOR 16 MiB
- WLAN : 2.4/5 GHz 4T4R (2x MediaTek MT7615N)
- Ethernet : 10/100/1000 Mbps
- Switch : MediaTek MT7530 (SoC)
- LED/keys : 8x/6x (3x buttons, 2x slide-switches)
- UART : through-hole on PCB
- J4: 3.3V, GND, TX, RX from triangle-mark
- 57600n8
- Power : 12VDC 1.5A
Flash instruction using initramfs image:
1. prepare the TFTP server with the initramfs image renamed to
"linux.trx-recovery" and IP address "192.168.11.2"
2. press the "AOSS" button while powering on the WSR-2533DHPL
3. after 10 seconds, release the "AOSS" button, WSR-2533DHPL downloads
the initramfs image and boot with it automatically
4. on the initramfs image, download the sysupgrade image to the device
and perform sysupgrade with it
5. wait ~120 seconds to complete flashing
Switch position overview:
- slide-switch1 (2x positions)
- "AUTO"
- "MANUAL" (not connected to gpio)
- slide-switch2 (3x positions)
- "ROUTER"
- "AP" (not connected to gpio)
- "WB"
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
[add note on switches, fix group->groups for state_default]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
It's unknown which switch port is used on mikrotik_rbm11g.
Disable this image until someone with actual device fixes this problem.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
The original idea of bitbanged I2C is to use i2c-gpio-custom
Since i2c-gpio-custom is no longer available on 5.4, use SoC I2C instead
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
The root file system is getting too big for this device and this breaks
the ramips/rt305x build.
Do not build images for this board by default to fix this problem.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Now that check-size uses IMAGE_SIZE by default, we can skip the argument from
image recipes to reduce redundancy.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[do not touch ar71xx]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Place DEVICE_VARS assignments at the top of the file or above Device/Default
to make them easier to find.
For ramips, remove redundant values already present in parent file.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[do not touch ar71xx, extend commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Currently kmod-i2c-* will not get into images unless kmod-i2c-core is added to
DEVICE_PACKAGES as well. By changing the dependencies from "depends on" to
"select", we do not have the issue anymore.
Furthermore, we can remove most occurrences of the package from DEVICE_PACKAGES
and similar variables, as it is now pulled by dependent modules such as:
- kmod-hwmon-lm75
- kmod-i2c-gpio
- kmod-i2c-gpio-custom
- kmod-i2c-mux
- kmod-i2c-ralink
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[do not touch ar71xx]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
TOTOLINK A3 is a clone of ipTIME A3. The only difference is the model name.
Specifications:
- SoC: MT7628AN
- RAM: DDR2 64MB
- Flash: SPI NOR 8MB
- WiFi:
- 2.4GHz: SoC internal
- 5GHz: MT7612EN
- Ethernet: 3x 10/100Mbps
- Switch: SoC internal
Installation via web interface:
1. Flash **initramfs** image through the stock web interface.
2. Boot into OpenWrt and perform sysupgrade with sysupgrade image.
Revert to stock firmware:
1. Perform sysupgrade with stock image.
Tested on device by JasonHCH <hsuan670629@gmail.com>
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Currently kmod-ata-* will not get into images unless kmod-ata-core is added to
DEVICE_PACKAGES as well. By changing the dependencies from "depends on" to
"select", we do not have the issue anymore.
Furthermore, we can remove most occurrences of the package from DEVICE_PACKAGES
and similar variables, as it is now pulled by dependent modules such as:
- kmod-ata-ahci
- kmod-ata-ahci-mtk
- kmod-ata-sunxi
While at it, use AddDepends/ata for kmod-ata-pdc202xx-old.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
