Commit Graph

905 Commits

Author SHA1 Message Date
David Bauer
1239668648 mediatek: add support for GL.iNet GL-MT2500
Hardware
--------
SoC:  MediaTek MT7981BA
RAM:  1GB DDR4 (NANYA NT5AD512M16C4-JR)
MMC:  8GB eMMC (Samsung 8GTF4R)
ETH:  1000Base-T LAN (ePHY)
      2500Base-T WAN (MaxLinear GPY211C)
BTN:  1x Reset Button
LED:  System (blue/white)
      VPN (white)
USB:  1x USB-A (USB 3.0)
UART: 115200 8N1 - Pinout on board next to LAN port
      Don't connect 3.3V!

Known Issues
------------
U-Boot vendor recovery does not seem to accept any images, neither
GL.iNet images nor OpenWrt images. Recovery requires serial access!

Installation
------------
Upload the OpenWrt sysupgrade image to the Gl.iNet Web-UI. Make sure to
not retain existing settings.

Signed-off-by: David Bauer <mail@david-bauer.net>
2023-11-27 08:02:41 +01:00
Tony Ambardar
b16e14a220 image: use helper function for size units
Add the make function 'exp_units' for helping evaluate k/m/g size units in
expressions, and use this to consistently replace many ad hoc substitutions
like '$(subst k,* 1024,$(subst m, * 1024k,$(IMAGE_SIZE)))' in makefiles.

Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
2023-11-26 18:37:20 +01:00
Rosen Penev
3eb899fd36
mediatek: use mac-base
mac-address-increment is deprecated.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2023-11-25 23:45:26 +01:00
Rosen Penev
405bc5be13
mediatek: convert to nvmem-layout
Will allow removing mac-address-increment.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2023-11-25 23:45:26 +01:00
Chukun Pan
07482d15af
mediatek: filogic: reorder alphabetically
Reorder scripts and image recipes to keep alphabetical order.

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
2023-11-25 23:16:35 +01:00
Chukun Pan
b74ae69596
mediatek: filogic: remove kmod-usb2 for GL-MT6000
The usb driver requires kmod-usb3, not kmod-usb2.
Remove the useless kmod-usb2 from default package.

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
2023-11-25 23:16:34 +01:00
Chukun Pan
1be6347b7d
mediatek: Cetron CT3003: fixes typo for spi properties
Same as commit 3674689, correct 'buswidth' to 'bus-width'.
Also move the nmbm properties outside the partition definition.

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
2023-11-25 23:16:34 +01:00
Hauke Mehrtens
d99aed31a0 mediatek: filogic: Fix GPIOs for Zbtlink ZBT-Z8102AX
The PGIO configuration should be added for the ZBT-Z8102AX and not the ZBT-Z8103AX

Fixes: c8c2f52262 ("mediatek: add support for Zbtlink ZBT-Z8102AX")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2023-11-25 22:25:42 +01:00
Valerio 'ftp21' Mancini
b5df398a36 mediatek: add Zyxel EX5601-T0 with uboot custom partition
The flash procedure is similar to the Xiaomi AX6000 router.

Load openwrt-mediatek-filogic-zyxel_ex5601-t0-ubootmod-initramfs-recovery.itb from original Zyxel U-Boot:

tftpboot openwrt-mediatek-filogic-zyxel_ex5601-t0-ubootmod-initramfs-recovery.itb
bootm 0x46000000
Load mtd-rw
insmod /lib/modules/$(uname -r)/mtd-rw.ko i_want_a_brick=1

Format ubi and create ubootenv partitions

ubidetach -p /dev/mtd5; ubiformat /dev/mtd5 -y; ubiattach -p /dev/mtd5
ubimkvol /dev/ubi0 -n 0 -N ubootenv -s 128KiB
ubimkvol /dev/ubi0 -n 1 -N ubootenv2 -s 128KiB
Copy openwrt-mediatek-filogic-zyxel_ex5601-t0-ubootmod-initramfs-recovery.itb to /tmp and create recovery partition.
If your recovery image is larger than 10MiB, size the recovery partition accordingly to make it fit.

ubimkvol /dev/ubi0 -n 2 -N recovery -s 10MiB
ubiupdatevol /dev/ubi0_2  openwrt-mediatek-filogic-zyxel_ex5601-t0-ubootmod-initramfs-recovery.itb
Copy preloader and uboot to /tmp and write them in the mtd

mtd write /tmp/openwrt-mediatek-filogic-zyxel_ex5601-t0-ubootmod-preloader.bin bl2
mtd write /tmp/openwrt-mediatek-filogic-zyxel_ex5601-t0-ubootmod-bl31-uboot.fip fip
Now write the firmware:
sysupgrade -n  /tmp/openwrt-mediatek-filogic-zyxel_ex5601-t0-ubootmod-squashfs-sysupgrade.itb

To create a correct BL2, I had to add a profile for 'spim:4k+256' as I could not find a way to value the variable 'NAND_TYPE'.

Features and fixes from hitech95 tree has been squashed, I'm attaching his commit message:

The Power LED was not working correctly and not reacting
 to the boot process and statuses.

The board has space (footprint) for an unpopulated Zigbee chip,
 while we dont know the device model having this chip populated
 we have to assure that the common dts doesnt enable
 interfaces that share pins with such device.

In this instance the PCIe and the uart1 and uart2 are disabled.
Some of the control PCIE pins seems to be used for the Zigbee chip,
 UART1 seems to be used as a flash port while UART2 should be the
 main comunication interface of Zigbee chip.

The Zigbee chip should be a EFR32MG21. But the pins used for UART
 seems to be not on standard PINS used by other adapters.
 So it cannot run firmwares shared on the web.
 But it should be possible to build a custom firmware with
 the corrtect pinmux.

This commit also contains the following squashed commit from hitech95
 - mediatek: fix sysupgrade for Zyxel EX7601-T0 ubootmod

Changes and fixes added in common board:
 - added aliases for boot status leds.
 - added aliases for the mac-label-device.
 - added pin claims for core features (MDIO and UART 0)
 - added default LEDs configuration (01_leds)
 - added default network configuration (02_network)
 - added missing kmod-usb3 module for USB3
 - fixed LED names
 - fixed reset pin for SLIC chip
 - removed unused pinmux configurations and devices
 - fix LAN (switch) port numbering
 - using nvmem cells for wifi eeprom, dropping deprecated "mediatek,mtd-eeprom"
 - proper factory partition and mac address handling
 - cleaned up spi_nand sections and partition

Changes and fixxes added in stock layout:
 - added NMBM, if u-boot has it, the kernel must be informed.

Co-authored-by: Nicolò Veronese <nicveronese@gmail.com>
Co-developed-by: Nicolò Veronese <nicveronese@gmail.com>
Signed-off-by: Nicolò Veronese <nicveronese@gmail.com>
Signed-off-by: Valerio 'ftp21' Mancini <ftp21@ftp21.eu>
2023-11-25 14:51:21 +01:00
Daniel Golle
1b70025ad1 mediatek: remove DTS property added by mistake
Remove bogus 'phy-handle = <&phy0>;', an undefined reference.

Fixes: c8c2f52262 ("mediatek: add support for Zbtlink ZBT-Z8102AX")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-11-25 03:22:47 +00:00
Daniel Golle
c8c2f52262 mediatek: add support for Zbtlink ZBT-Z8102AX
Specifications:
SoC: MediaTek MT7981B
RAM: 1024MiB
Flash: SPI-NAND 128 MiB
Switch: 1 WAN, 4 LAN (Gigabit)
USB: two M.2 slots for 5G modems via USB 3.0 hub, external USB 3.0 port
Buttons: Reset, Mesh
Power: DC 12V 1A
WiFi: MT7976CN
UART: 115200n8
UART Layout:
VCC-RX-TX-GND

Installation:
A. Through OpenWrt Dashboard:
If your router comes with OpenWrt preinstalled (modified by the seller),
you can easily upgrade by going to the dashboard (192.168.1.1) and then
navigate to System -> Backup/Flash firmware, then flash the firmware

B. Through TFTP
Standard installation via UART:

1. Connect USB Serial Adapter to the UART, (NOTE: Don't connect the VCC pin).
2. Power on the router. Make sure that you can access your router via UART.
3. Restart the router then repeatedly press ctrl + c to skip default boot.
4. Type > bootmenu
5. Press '2' to select upgrade firmware
6. Press 'Y' on 'Run image after upgrading?'
7. Press '0' and hit 'enter' to select TFTP client (default)
8. Fill the U-Boot's IP address and TFTP server's IP address.
9. Finally, enter the 'firmware' filename.

Based on patch adding support for similar Zbtlink ZBT-Z8103AX device by
Ian Ishmael C. Oderon.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-11-24 21:28:35 +00:00
John Audia
2b75f108fb kernel: bump 6.1 to 6.1.63
Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.1.63

Removed upstreamed:
	generic/backport-6.1/815-v6.6-2-leds-turris-omnia-Drop-unnecessary-mutex-locking.patch
	generic/backport-6.1/815-v6.7-1-leds-turris-omnia-Do-not-use-SMBUS-calls.patch
	ixp4xx/patches-6.1/0007-watchdog-ixp4xx-Make-sure-restart-always-works.patch

Manually rebased:
	bcm27xx/patches-6.1/950-0606-hwrng-bcm2835-sleep-more-intelligently.patch

All other patches automatically rebased.

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.63&id=7d0e60e4ff840e97fb18afb2a7344442c10a6fdf
2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.63&id=63cdeb20ee3bfef820b045b8d3b8395f9f815a74
3. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.63&id=8803da01fe1b4ca3d37745283f7e73c6c2558c0c

Build system: x86/64
Build-tested: x86/64/AMD Cezanne
Run-tested: x86/64/AMD Cezanne

Signed-off-by: John Audia <therealgraysky@proton.me>
2023-11-23 22:51:52 +01:00
Rani Hod
aaeb379023 mediatek: fiilogic: device tree switch@1f fix
Quite a few `fiilogic` devices use the `mt7531` switch.
Some of them have a DT node that looks like:
```
switch: switch@0 {
	compatible = "mediatek,mt7531";
	reg = <31>;
...
};
```
This commit changes the DT node name to `switch@1f`.

Signed-off-by: Rani Hod <rani.hod@gmail.com>
2023-11-22 19:42:23 +02:00
Chukun Pan
626344c992 mediatek: filogic: add JCG Q30 PRO support
Hardware specification:
  SoC: MediaTek MT7981B 2x A53
  Flash: Winbond 128MB
  RAM: DDR3 256MB
  Ethernet: 4x 10/100/1000 Mbps
  Switch: MediaTek MT7531AE
  WiFi: MediaTek MT7976C
  Button: Reset
  Power: DC 12V 1A

Flash instructions:
  1. Connect to your PC via the Gigabit port of the router,
     set a static ip on the ethernet interface of your PC.
     (ip 192.168.1.254, gateway 192.168.1.1)
  2. Attach UART, pause at u-boot menu.
  3. Select "Upgrade ATF BL2", then use preloader.bin
  4. Select "Upgrade ATF FIP", then use bl31-uboot.fip
  5. Download the initramfs image, and type "reset",
     waiting for tftp recovery to complete.
  6. After openwrt boots up, perform sysupgrade.

Note:
  1. Since NMBM is disabled, we must back up all partitions.
  2. Although we can upgrade new firmware in the stock firmware,
     we need the special fit image signature of MediaTek and
     dual boot (hack kernel) to make u-boot boot it. So just
     abandon these hacks and flash it via the serial port.

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
2023-11-19 16:52:16 +01:00
Petr Štetiar
8fc496be86
treewide: fix shell errors during dump stage
Fixes following issues:

 bash: -c: line 1: `echo 1686820180<LINUX_VERMAGIC> | /staging_dir/host/bin/mkhash md5 | cut -b1-8'
 bash: -c: line 1: `echo 1686820180<LINUX_VERMAGIC> | /staging_dir/host/bin/mkhash md5 | sed -E 's/(.{8})(.{4})(.{4})(.{4})(.{10})../\1-\2-\3-\4-\500/''
 bash: -c: line 1: syntax error near unexpected token `|'
 bash: line 1: *1024*1024: syntax error: operand expected (error token is "*1024*1024")
 bash: line 1: (64 + ): syntax error: operand expected (error token is ")")
 expr: syntax error: missing argument after '+'

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2023-11-13 14:01:25 +01:00
Roland Reinl
44cd32d764 mediatek: Add support for TP-Link EAP225v5
Device specification:
- MT7629 with 16MB NOR flash W25Q128 and 128 MB DDR3 RAM.
- MT7761N and MT7762N wireless chips (currenlty no driver in OpenWrt available)
  - WiFi is NOT working on this device
- Dual core but second CPU doesn't seem to work (Error message during boot: "CPU1: failed to come online")

There are two similar merge requests for similar devices with the same issues:
- https://github.com/openwrt/openwrt/pull/12286
- https://github.com/openwrt/openwrt/pull/5084

UART interface is next to the reset button, pinout:
- 1: TX (the pin with the arrow marker)
- 2: RX
- 3: GND
- 4: VCC

UART settings: 115200,8n1, 3.3V

U-Boot menu can be entered by pressing Ctrl+B during startup.

Booting initramfs:
- Set your computers IP adress to 192.168.1.110
- Run a TFTP server providing the initramfs image
- Power on the AP, press Ctrl+B to get to the U-Boot menu
- Select "1. System Load Linux to SDRAM via TFTP"
- Update kernel file name, input server IP and input device IP (if they deviate from the defaults)
- After booting, create a backup of all partitions, especially for kernel and root_fs. They are required for reverting back to stock firmware
- The sysupgrade image can be flashed now

MAC adresses:
- LAN and 2.4GHz use the same MAC (the one printed on the device)
- 5GHz WiFi MAC is LAN MAC + 1

GPIOs:
- GPIO 21 is the reset pin (low active)
- GPIO 55 is for the green LED (active high)
- GPIO 56 is for the yellow/amber LED (active high)

Signed-off-by: Roland Reinl <reinlroland+github@gmail.com>
2023-11-12 17:39:52 +01:00
Roland Reinl
e3a6945b58 mediatek: Add support for D-Link EAGLE PRO AI M32
Specification:
 - MT7622BV SoC with 2.4GHz wifi
 - MT7975AN + MT7915AN for 5GHz
 - MT7531BE Switch
 - 512MB RAM
 - 128 MB flash
 - 3 LEDs (red, orange, white)
 - 2 buttons (WPS and Reset)

MAC addresses:
 - WAN MAC is stored in partition "Odm" at offset 0x83
 - LAN (as printed on the device) is WAN MAC + 1
 - WLAN MAC (2.4 GHz) is WAN MAC + 2
 - WLAN MAC (5GHz) is WAN MAC + 3

Disassembly: Remove 4 screws in the bottom and 2 screws in the top (after removing the blue cover on the top), then the board can be pulled out.

The pins for the serial console are already labeled on the board (VCC, TX, RX, GND). Serial settings: 3.3V, 115200,8n1

Flashing via Recovery Web Interface:
- Set your IP address to 192.168.0.10, subnetmask 255.255.255.25
- Press the reset button while powering on the deivce
- Keep the reset button pressed until the status LED blinks fast
- Open a Chromium based and goto http://192.168.0.1
- Download openwrt-mediatek-mt7622-dlink_eagle-pro-ai-m32-a1-squashfs-recovery.bin

Flashing via uBoot:
- Open the case, connect to the UART console
- Set your IP address to 10.10.10.3, subnet mask 255.255.255.0. Connect to one of the LAN interfaces of the router
- Run a tftp server which provides openwrt-mediatek-mt7622-dlink_eagle-pro-ai-m32-initramfs-kernel.bin. You can rename the file to iverson_uImage (no extension), then you don't have to enter the whole file name in uboot later.
- Power on the device and select "1. System Load Linux to SDRAM via TFTP." in the boot menu
- Enter image file, tftp server IP and device IP (if they differ from the default).
- TFTP download to RAM will start. After a few seconds OpenWrt initramfs should start
- The initramfs is accessible via 192.168.1.1, change your IP address accordingly (or use multiple IP addresses on your interface)
- Create a backup of the Kernel1 partition, this file is required if a revert to stock should be done later
- Perform a sysupgrade using openwrt-mediatek-mt7622-dlink_eagle-pro-ai-m32-squashfs-sysupgrade.bin
- Reboot the device. OpenWrt should start from flash now

Revert back to stock using the Recovery Web Interface:
- Set your IP address to 192.168.0.10, subnetmask 255.255.255.25
- Press the reset button while powering on the deivce
- Keep the reset button pressed until the status LED blinks fast
- Open a Chromium based and goto http://192.168.0.1
- Flash a decrypted firmware image from D-Link. Decrypting an firmware image is described below.

Decrypting a D-Link firmware image:
- Download https://github.com/RolandoMagico/firmware-utils/blob/M32/src/m32-firmware-util.c
- Compile a binary from the downloaded file, e.g. gcc m32-firmware-util.c -lcrypto -o m32-firmware-util
- Run ./m32-firmware-util M32 --DecryptFactoryImage <OriginalFirmware> <OutputFile>
- Example for firmware 1.03.01_HOTFIX: ./m32-firmware-util M32 --DecryptFactoryImage M32-REVA_1.03.01_HOTFIX.enc.bin M32-REVA_1.03.01_HOTFIX.decrypted.bin

Revert back to stock using uBoot:
- Open the case, connect to the UART console
- Set your IP address to 10.10.10.3, subnet mask 255.255.255.0. Connect to one of the LAN interfaces of the router
- Run a tftp server which provides the previously created backup of the Kernel1 partition. You can rename the file to iverson_uImage (no extension), then you don't have to enter the whole file name in uboot later.
- Power on the device and select "2. System Load Linux Kernel then write to Flash via TFTP." in the boot menu
- Enter image file, tftp server IP and device IP (if they differ from the default).
- TFTP download to FLASH will start. After a few seconds the stock firmware should start again

There is also an image openwrt-mediatek-mt7622-dlink_eagle-pro-ai-m32-a1-squashfs-tftp.bin which can directly be flashed via U-Boot and TFTP. It can be used if no backup of the Kernel1 partition is reuqired.

Flahsing via OEM web interface is currently not possible, the OEM images are encrypted and require a specific memory layout which is not compatible to the partition layout of OpenWrt.

Signed-off-by: Roland Reinl <reinlroland+github@gmail.com>
2023-11-12 17:33:41 +01:00
John Audia
573c8c3d78 kernel: bump 5.15 to 5.15.138
Changelog: https://cdn.kernel.org/pub/linux/kernel/v5.x/ChangeLog-5.15.138

Removed upstreamed:
	generic/backport-5.15/819-v6.6-0018-nvmem-imx-correct-nregs-for-i.MX6SLL.patch[1]
	generic/backport-5.15/819-v6.6-0019-nvmem-imx-correct-nregs-for-i.MX6UL.patch[2]
	generic/backport-5.15/819-v6.6-0020-nvmem-imx-correct-nregs-for-i.MX6ULL.patch[3]

All other patches automatically rebased.

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.138&id=6e22bf6f00d593b0a7e0b2f418fde89317424671
2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.138&id=6efd498009b987a92f57f3bdae476f0503364fb7
3. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.138&id=6e22bf6f00d593b0a7e0b2f418fde89317424671

Build system: x86_64
Build-tested: ramips/tplink_archer-a6-v3
Run-tested: ramips/tplink_archer-a6-v3

Signed-off-by: John Audia <therealgraysky@proton.me>
2023-11-10 17:33:59 +01:00
David Bauer
ae500e62e2 mediatek: add label-mac for GL.iNet GL-MT3000
The MAC-address of gmac0 matches the one printed on the bottom label.

Signed-off-by: David Bauer <mail@david-bauer.net>
2023-11-03 23:06:33 +01:00
Łukasz M
5a603c7a31 mediatek: mt7981: improve fan behaviour
This doubles the number of cooling-levels.
In addition the fan is turned on with a low speed at lower temperatures
and with a higher speed at higher temperatures.
This also attempts to reduce the likelihood of constant start-stop actions.

The change only affects the GL.iNet MT3000 and has been tested with it.

Signed-off-by: Łukasz M <lukasz1992m@gmail.com>
2023-11-03 23:06:07 +01:00
Mikhail Zhilkin
45a50a06fb treewide: fix MERCUSYS brand spelling
This commit fixes MERCUSYS brand spelling. The proper name is capitalized.

Link: https://www.mercusys.com/
Link: https://github.com/torvalds/linux/blob/master/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_core.c#L7779

Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
2023-11-03 23:06:07 +01:00
Patryk Kowalczyk
0c3f4bd85e filogic: fix wifi eeprom filename for tuf-ax6000
The router use mt7986_eeprom_mt7976_dual.bin

Fixes: d522ccecb2 ("filogic: add support for ASUS TUF AX6000")

Signed-off-by: Patryk Kowalczyk <patryk@kowalczyk.ws>
2023-11-03 23:06:07 +01:00
Patryk Kowalczyk
d522ccecb2 filogic: add support for ASUS TUF AX6000
Hardware
========
SOC: MediaTek MT7986
RAM: 512MB DDR3
FLASH: 256MB SPI-NAND
WIFI: Mediatek MT7986 DBDC 802.11ax 2.4/5 GHz 4T4R
ETH: MediaTek MT7530 Switch (LAN)
MaxLinear GPY211C 2.5 N-Base-T PHY (WAN)
MaxLinear GPY211C 2.5 N-Base-T PHY (LAN)
UART: 3V3 115200 8N1 (Do not connect VCC)
USB 3.1

Installation
============

Download the OpenWrt initramfs image. Copy the image to a TFTP server
reachable at 192.168.1.70/24. Rename the image to TUF-AX6000.bin.

Connect to the serial console, interrupt the auto boot process by
pressing '4' when prompted or press '1' and set client IP, server
IP and name of the image.

yOU don't need to open the case or even soldering anything.
use three goldpin wires, remove their plastic cover and connect
them to the console pinout via the case holes.

You can see three holes
From Bottom: RX, TX, Ground - partially covered

Download & Boot the OpenWrt initramfs image.

In case of option '4'
$ setenv ipaddr 192.168.1.1
$ setenv serverip 192.168.1.70
$ tftpboot 0x46000000 TUF-AX6000.bin
$ bootm 0x46000000

In case of option '1'
1: Load System code to SDRAM via TFTP.
Please Input new ones /or Ctrl-C to discard
Input device IP (192.168.1.1) ==:
Input server IP (192.168.1.70) ==:
Input Linux Kernel filename (TUF-AX6000.trx) ==:

Wait for OpenWrt to boot. Transfer the sysupgrade
image to the device using scp and install using sysupgrade.

$ sysupgrade -n <path-to-sysupgrade.bin>

Missing features
================

2.5Gb LAN port LED is ON during boot or when the LAN cable is disconnected

The cover yellow light is not supported. (only blue one)

Signed-off-by: Patryk Kowalczyk <patryk@kowalczyk.ws>
2023-10-31 21:12:15 +01:00
Tianling Shen
423186d7d8 mediatek: add CMCC RAX3000M support
Hardware specification:
  SoC: MediaTek MT7981B 2x A53
  Flash: 64GB eMMC or 128 MB SPI-NAND
  RAM: 512MB
  Ethernet: 4x 10/100/1000 Mbps
  Switch: MediaTek MT7531AE
  WiFi: MediaTek MT7976C
  Button: Reset, Mesh
  Power: DC 12V 1A
- UART: 3.3v, 115200n8
  --------------------------
  |         Layout         |
  |   -----------------    |
  | 4 | GND TX VCC RX | <= |
  |   -----------------    |
  --------------------------

Gain SSH access:
1. Login into web interface, and download the configuration.
2. Enter fakeroot, decompress the configuration:
   tar -zxf cfg_export_config_file.conf
3. Edit 'etc/config/dropbear', set 'enable' to '1'.
4. Edit 'etc/shadow', update (remove) root password:
   'root::19523:0:99999:7:::'
5. Repack 'etc' directory:
   tar -zcf cfg_export_config_file.conf etc/
   * If you find an error about 'etc/wireless/mediatek/DBDC_card0.dat',
     just ignore it.
6. Upload new configuration via web interface, now you can SSH to RAX3000M.

Check stroage type:
Check the label on the back of the device:
"CH EC CMIIT ID: xxxx" is eMMC version
"CH    CMIIT ID: xxxx" is NAND version

eMMC Flash instructions:
1. SSH to RAX3000M, and backup everything, especially 'factory' part.
   ('data' partition can be ignored, it's useless.)
2. Write new GPT table:
   dd if=openwrt-mediatek-filogic-cmcc_rax3000m-emmc-gpt.bin of=/dev/mmcblk0 bs=512 seek=0 count=34 conv=fsync
3. Erase and write new BL2:
   echo 0 > /sys/block/mmcblk0boot0/force_ro
   dd if=/dev/zero of=/dev/mmcblk0boot0 bs=512 count=8192 conv=fsync
   dd if=openwrt-mediatek-filogic-cmcc_rax3000m-emmc-preloader.bin of=/dev/mmcblk0boot0 bs=512 conv=fsync
4. Erase and write new FIP:
   dd if=/dev/zero of=/dev/mmcblk0 bs=512 seek=13312 count=8192 conv=fsync
   dd if=openwrt-mediatek-filogic-cmcc_rax3000m-emmc-bl31-uboot.fip of=/dev/mmcblk0 bs=512 seek=13312 conv=fsync
5. Set static IP on your PC:
   IP 192.168.1.254, GW 192.168.1.1
6. Serve OpenWrt initramfs image using TFTP server.
7. Cut off the power and re-engage, wait for TFTP recovery to complete.
8. After OpenWrt has booted, perform sysupgrade.
9. Additionally, if you want to have eMMC recovery boot feature:
     (Don't worry! You will always have TFTP recovery boot feature.)
   dd if=openwrt-mediatek-filogic-cmcc_rax3000m-initramfs-recovery.itb of=/dev/mmcblk0p4 bs=512 conv=fsync

NAND Flash instructions:
1. SSH to RAX3000M, and backup everything, especially 'Factory' part.
2. Erase and write new BL2:
   mtd erase BL2
   mtd write openwrt-mediatek-filogic-cmcc_rax3000m-nand-preloader.bin BL2
3. Erase and write new FIP:
   mtd erase FIP
   mtd write openwrt-mediatek-filogic-cmcc_rax3000m-nand-bl31-uboot.fip FIP
4. Set static IP on your PC:
   IP 192.168.1.254, GW 192.168.1.1
5. Serve OpenWrt initramfs image using TFTP server.
6. Cut off the power and re-engage, wait for TFTP recovery to complete.
7. After OpenWrt has booted, erase UBI volumes:
   ubidetach -p /dev/mtd0
   ubiformat -y /dev/mtd0
   ubiattach -p /dev/mtd0
8. Create new ubootenv volumes:
   ubimkvol /dev/ubi0 -n 0 -N ubootenv -s 128KiB
   ubimkvol /dev/ubi0 -n 1 -N ubootenv2 -s 128KiB
9. Additionally, if you want to have NAND recovery boot feature:
     (Don't worry! You will always have TFTP recovery boot feature.)
   ubimkvol /dev/ubi0 -n 2 -N recovery -s 20MiB
   ubiupdatevol /dev/ubi0_2 openwrt-mediatek-filogic-cmcc_rax3000m-initramfs-recovery.itb
10. Perform sysupgrade.

Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
2023-10-28 19:05:07 +02:00
John Audia
b357564463 kernel: bump 6.1 to 6.1.57
Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.1.57

Manually rebased:
	generic/pending-6.1/702-net-ethernet-mtk_eth_soc-enable-threaded-NAPI.patch

Removed upstreamed:
	qualcommax/patches-6.1/0134-PCI-qcom-Fixing-broken-pcie-enumeration-for-2_3_3-co.patch[1]

All other patches automatically rebased.

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.57&id=2dfb5f324d799f4545e17631415aba6d302a8e2b

Build system: x86/64
Build-tested: x86/64/AMD Cezanne
Run-tested: x86/64/AMD Cezanne

Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: John Audia <therealgraysky@proton.me>
2023-10-14 15:51:53 +02:00
John Audia
1a15a8cdb9 kernel: bump 6.1 to 6.1.56
Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.1.56

Removed upstreamed:
	bcm53xx/patches-6.1/032-v6.6-0008-ARM-dts-BCM5301X-Extend-RAM-to-full-256MB-for-Linksy.patch[1]

All other patches automatically rebased.

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.56&id=226590fbd96717fce218878044df3568c825ba8e

Build system: x86/64
Build-tested: x86/64/AMD Cezanne, filogic/xiaomi_redmi-router-ax6000-ubootmod
Run-tested: x86/64/AMD Cezanne, filogic/xiaomi_redmi-router-ax6000-ubootmod

Signed-off-by: John Audia <therealgraysky@proton.me>
2023-10-08 14:01:47 +02:00
John Audia
ac3a5911da kernel: bump 5.15 to 5.15.134
Changelog: https://cdn.kernel.org/pub/linux/kernel/v5.x/ChangeLog-5.15.134

Removed upstreamed:
	generic/backport-5.15/894-Fix-up-backport-for-13619703038.patch[1]

All other patches automatically rebased.

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.134&id=d7acb7031758141225844bea073860b48fd92092

Build system: x86_64
Build-tested: ramips/tplink_archer-a6-v3
Run-tested: ramips/tplink_archer-a6-v3

Signed-off-by: John Audia <therealgraysky@proton.me>
2023-10-07 10:00:03 -04:00
Daniel Golle
ed3ccf44e6 mediatek: fix wrong variable name in patch for Linux 6.1
The name of the variable holding the pointer to the private struct has
changed between Linux 5.15 and Linux 6.1 and adding the identical patch
fixing PCIe #PERST de-assert broke the build on Linux 6.1.
Also change the name in the patch to fix the build.

Fixes: 6a2e17d5c1 ("mediatek: fix PCIe #PERST being de-asserted too early")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-10-05 20:40:12 +02:00
John Audia
89895937dd kernel: bump 5.15 to 5.15.133
Changelog: https://cdn.kernel.org/pub/linux/kernel/v5.x/ChangeLog-5.15.133

Removed upstreamed:
	bcm47xx/patches-5.15/101-v5.18-mtd-rawnand-brcmnand-Allow-SoC-to-provide-I-O-operations.patch[1]

Cherry picked build fix.[2] All other patches automatically rebased.

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.133&id=56cf9f446b331414a15ef0e8dedf23583ec2c427
2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/stable-queue.git/tree/queue-5.15/fix-up-backport-of-136191703038-interconnect-teach-l.patch

Build system: x86_64
Build-tested: ramips/tplink_archer-a6-v3
Run-tested: ramips/tplink_archer-a6-v3

Signed-off-by: John Audia <therealgraysky@proton.me>
2023-10-04 21:03:12 +02:00
Daniel Golle
6a2e17d5c1
mediatek: fix PCIe #PERST being de-asserted too early
The driver for MediaTek gen3 PCIe hosts de-asserts all reset
signals at the same time using a single register write operation.
Delay the de-assertion of the #PERST signal by 100ms as some PCIe
devices fail to come up otherwise.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-10-03 17:38:34 +02:00
Mikhail Zhilkin
85b0d7592c mediatek: fix eeprom loading (Mercusys MR90X v1)
Commit mt76: drop default eeprom file for mt7986-firmware
(e3aa645b26) breaks eeprom loading for
Mercusys MR90X v1. As a result WiFi is not working at all.

This commit adds Mercusus MR90x to the caldata script (it works after the
commit mentioned above). And we can safely drop "81_fix_eeprom" script
as it's no longer required.

Fixes: e3aa645b26
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
2023-10-02 11:40:27 +01:00
Jianhui Zhao
fe10f97439 filogic: add support for GL.iNet GL-MT6000
Hardware specification:
* SoC: MediaTek MT7986A 4x A53
* Flash: 8GB EMMC
* RAM: 1GB DDR4
* Ethernet:
  * 2x2.5G RJ45 port (RTL8221B)
  * 4x1G RJ45 ports (MT7531AE)
* WLAN:
  * 2.4GHz: MT7976GN 4T4R
  * 5GHz: MT7976AN 4T4R
* Button: Reset
* LED: 1 x dual color LED
* USB: 1 x USB 3.0
* Power: DC 12V 4A
* UART: 3V3 115200 8N1 (Pinout: GND TX RX VCC)
* JTAG: 9 PIN

If you want to use u-boot from OpenWrt, you can upgrade it safely.
* bl2: openwrt-mediatek-filogic-glinet_gl-mt6000-preloader.bin
* fip: openwrt-mediatek-filogic-glinet_gl-mt6000-bl31-uboot.fip

`openwrt-mediatek-filogic-glinet_gl-mt6000-squashfs-factory.bin` is used in OpenWrt's u-boot.

Signed-off-by: Jianhui Zhao <zhaojh329@gmail.com>
2023-09-29 00:18:26 +01:00
INAGAKI Hiroshi
7383eb266b mediatek: add support for Buffalo WSR-3200AX4S
Buffalo WSR-3200AX4S is a 2.4/5 GHz band 11ax (Wi-Fi 6) router, based on
MT7622B.

Specification:

- SoC         : MediaTek MT7622B
- RAM         : DDR3 512 MiB
- Flash       : SPI-NAND 128 MiB (Winbond W25N01GVZEIG)
- WLAN        : 2.4/5 GHz 4T4R
  - 2.4 GHz   : MediaTek MT7622B (SoC)
  - 5 GHz     : MediaTek MT7915
- Ethernet    : 5x 10/100/1000 Mbps
  - Switch    : MediaTek MT7531
- LEDs/Keys   : 6x/5x (2x: buttons, 3x: slide-switches)
- UART        : through-hole on PCB (J4)
  - assignment: 3.3V, GND, TX, RX from tri-angle marking
  - settings  : 115200n8
- Power       : 12 VDC, 1.5 A

Flash instruction using factory.bin image:

1. Boot WSR-3200AX4S with "Router" mode
2. Access to "http://192.168.11.1/" and open firmware update page
   ("ファームウェア更新")
3. Select the OpenWrt factory.bin image and click update ("更新実行")
   button
4. Wait ~120 seconds to complete flashing

Note:

- This device has 2x OS images on flash. The first one will always be
  used for booting and the secondary is for backup.

- This support generates multiple factory*.bin image:

  - factory.bin      : for flashing from OEM WebUI
  - factory-uboot.bin: for flashing from U-Boot or clean installation
                       via sysupgrade (don't use for normal sysupgrade)

Known issues:

- Wi-Fi MAC addresses won't be applied to each adapter.

MAC Addresses:

LAN    : C4:3C:EA:xx:xx:60 (board_data, mac (text))
WAN    : C4:3C:EA:xx:xx:60 (board_data, mac (text))
2.4 GHz: C4:3C:EA:xx:xx:61
5 GHz  : C4:3C:EA:xx:xx:68

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2023-09-24 18:42:12 +02:00
INAGAKI Hiroshi
9f640cae75 mediatek: separate dts/dtsi for Buffalo WSR series
Separate dts/dtsi from the dts of Buffalo WSR-2533DHP2 to prepare adding
suppport for WSR-3200AX4S.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2023-09-24 18:42:12 +02:00
INAGAKI Hiroshi
e8646f5b3d mediatek: expand kernel size to 6MiB for WSR-2533DHP2
Expand kernel partition size on WSR-2533DHP2 for the kernel larger than
4 MiB.
To prevent upgrading from old firmware before this commit, bump the
compat version to 1.1 and add a message for forced sysupgrade using
factory-uboot.bin image.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2023-09-24 18:42:11 +02:00
INAGAKI Hiroshi
d0929006f2 mediatek: merge trx helpers in image/mt7622.mk
Merge similar helpers of trx image generation, "buffalo-kernel-trx" and
"trx-nand".

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2023-09-24 18:42:11 +02:00
INAGAKI Hiroshi
4d9113017b mediatek: drop pwm7_pins from Buffalo WSR-2533DHP2
MediaTek MT7622 doesn't support ch7 of PWM and pinctrl groups were dropped from
driver source[0]. So pwm7-related groups are unavailable now, then, kernel shows a
warning.

[    0.370264] mt7622-pinctrl 10211000.pinctrl: invalid group "pwm_ch7_2" for function "pwm"

Drop that pinmux from pinctrl node.

[0]: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/drivers/pinctrl/mediatek/pinctrl-mt7622.c?id=57972641810a97566ffd13e4be3f6a66d61eb3b5

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2023-09-24 18:42:11 +02:00
INAGAKI Hiroshi
94606abf63 mediatek: add label-mac-device for Buffalo WSR-2533DHP2
Add label-mac-device with "&gmac0" phandle for Buffalo WSR-2533DHP2.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2023-09-24 18:42:11 +02:00
INAGAKI Hiroshi
de62e01652 mediatek: update NVMEM bindings for Buffalo WSR-2533DHP2
Update NVMEM-related nodes and use newer binding for MAC addresses on
Buffalo WSR-2533DHP2.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2023-09-24 18:42:11 +02:00
INAGAKI Hiroshi
6b8e7144c8 mediatek: update LED/Key bindings for Buffalo WSR-2533DHP2
Update LED and key nodes with newer DeviceTree bindings for WSR-2533DHP2.

- LED
  - use led-[0-9] for node name of LEDs
  - add "color" and "function" properties
  - drop default-state = "on" from green:power LED
    - this LED will be turned on by led-running alias

- key
  - drop unnecessary poll-interval property
  - use key-[0-9] for node name of keys

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2023-09-24 18:42:11 +02:00
Elbert Mai
75ee5546e9 mediatek: filogic: add support for Ubiquiti UniFi 6 Plus (U6+)
Ubiquiti U6+ is a dual-band WiFi 6 PoE access point.
It is a drop-in upgrade of the U6 lite.

Specifications
---

- SoC: MediaTek MT7981A dual-core ARM Cortex-A53 1.3 GHz
- RAM: 256 MB DDR3-2133 RAM
- Flash: 16 MB SPI NOR and 4 GB eMMC
- LAN: 1x Gigabit Ethernet with 802.3af/at support
- WLAN: MediaTek MT7976C 2x2 MIMO dual-band WiFi 6
- LEDs: 1x blue and 1x white
- Buttons: 1x reset button

Installation
---

1. Power device using a PoE injector or switch
2. Connect via Ethernet to the device with static IP 192.168.1.2
3. SSH into the device with password: ubnt

        $ ssh ubnt@192.168.1.20

4. Unlock kernel partitions for writing

        $ echo 5edfacbf > /proc/ubnthal/.uf

5. Confirm correct partitions

        $ grep PARTNAME /sys/block/mmcblk0/mmcblk0p6/uevent
        PARTNAME=kernel0
        $ grep PARTNAME /sys/block/mmcblk0/mmcblk0p7/uevent
        PARTNAME=kernel1
        $ grep PARTNAME /sys/block/mmcblk0/mmcblk0p8/uevent
        PARTNAME=bs

6. Set and confirm bootloader environment

        $ fw_setenv boot_openwrt "fdt addr \$(fdtcontroladdr); fdt rm /signature; bootubnt"
        $ fw_setenv bootcmd_real "run boot_openwrt"
        $ fw_printenv

7. Copy sysupgrade image to /tmp/openwrt.bin via scp
8. Copy kernel and rootfs to mmcblk0p6 and mmcblk0p7, respectively

        $ tar xf /tmp/openwrt.bin sysupgrade-ubnt_unifi-6-plus/kernel -O | dd of=/dev/mmcblk0p6
        $ tar xf /tmp/openwrt.bin sysupgrade-ubnt_unifi-6-plus/root -O | dd of=/dev/mmcblk0p7

9. Ensure device boots from mmcblk0p6

        $ echo -ne "\x00\x00\x00\x00\x2b\xe8\x4d\xa3" > /dev/mmcblk0p8

10. Reboot the device

        $ reboot

Signed-off-by: Elbert Mai <code@elbertmai.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
2023-09-24 17:16:16 +02:00
John Audia
2bda536a3d
kernel: bump 6.1 to 6.1.53
Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.1.53

Removed upstreamed:
	bcm53xx/patches-6.1/032-v6.6-0005-ARM-dts-BCM53573-Drop-nonexistent-usb-cells.patch[1]
	bcm53xx/patches-6.1/032-v6.6-0006-ARM-dts-BCM53573-Add-cells-sizes-to-PCIe-node.patch[2]
	bcm53xx/patches-6.1/032-v6.6-0007-ARM-dts-BCM53573-Use-updated-spi-gpio-binding-proper.patch[3]
	bcm53xx/patches-6.1/032-v6.6-0011-ARM-dts-BCM53573-Fix-Tenda-AC9-switch-CPU-port.patch[4]

All other patches automatically rebased.

Build system: x86/64
Build-tested: x86/64/AMD Cezanne
Run-tested: x86/64/AMD Cezanne

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.53&id=ee1d740374aa73fb32857685eb05167ad87458cf
2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.53&id=ab5154ae26c446136827451e907db45d7b92a76f
3. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.53&id=f5ff6897094fa161be55786cb9e5d5b1bf7a9049
4. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.53&id=0ef736fec61422794c4a991d46c4ec212b01d8d1

Signed-off-by: John Audia <therealgraysky@proton.me>
2023-09-23 13:10:28 +02:00
Daniel Golle
ce7209bd21 mediatek: add build for MT7981 RFB
Add build for the MTK3943 reference board for MT7981B+MT7976C.

**Hardware specification:**

 - SoC: MediaTek MT7981B 2x A53
 - Flash: various options
 - RAM: 256MB DDR3
 - Ethernet: 4 x 10/100/1000 Mbps via MT7531AE switch
        EITHER 1 x 10/100/1000 Mbps built-in PHY
            OR 1 x 10/100/1000/2500 Mbps MaxLinear GPY211C
 - Switch: MediaTek MT7531AE
 - WiFi: MediaTek MT7976C
 - Button: RST, WPS

**Flash instructions for SPIM-NAND:**
 - write *mt7981-rfb-spim-nand-preloader.bin to 'BL2' partition
 - write *mt7981-rfb-spim-nand-bl31-uboot.fip to 'FIP' partition
 - erase 'ubi' partition
 - reset board
 - create ubootenv and ubootenv2 UBI volumes in U-Boot
 - edit environment and set bootcmd, e.g.
   setenv bootconf 'config-1#mt7981-rfb-spim-nand#mt7981-rfb-mxl-2p5g-phy-eth1'
   setenv bootcmd 'ubi read $loadaddr fit; bootm $loadaddr#$bootconf'
 - load initramfs image via TFTP:
   setenv serverip 192.168.1.254
   setenv ipaddr 192.168.1.1
   setenv bootfile openwrt-mediatek-filogic-mediatek_mt7981-rfb-initramfs.itb
   saveenv ; saveenv
   tftpboot
   bootm $loadaddr#$bootconf
 - Now use sysupgrade to write OpenWrt firmware to flash.

SNFI-NAND, SPIM-NOR and eMMC all work very similar, a bootable SD card image
is also being generated. However, as the board I've been provided only comes
with SPIM-NAND all other boot media are untested.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-09-21 10:15:08 +01:00
John Audia
ac422c9788
kernel: bump 5.15 to 5.15.132
Changelog: https://cdn.kernel.org/pub/linux/kernel/v5.x/ChangeLog-5.15.132

Removed upstreamed:
	bcm53xx/patches-5.15/037-v6.6-0006-ARM-dts-BCM53573-Add-cells-sizes-to-PCIe-node.patch[1]
	bcm53xx/patches-5.15/037-v6.6-0007-ARM-dts-BCM53573-Use-updated-spi-gpio-binding-proper.patch[2]
	bcm53xx/patches-5.15/037-v6.6-0008-ARM-dts-BCM5301X-Extend-RAM-to-full-256MB-for-Linksy.patch[3]

All other patches automatically rebased.

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.132&id=b35f3ca1877e024887df205ede952863d65dad36
2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.132&id=2840d9b9c8750be270fb1153ccd5b983cbb5d592
3. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.132&id=f086e859ddc252c32f0438edff241859c0f022ce

Build system: x86_64
Build-tested: ramips/tplink_archer-a6-v3
Run-tested: ramips/tplink_archer-a6-v3

Signed-off-by: John Audia <therealgraysky@proton.me>
2023-09-20 14:13:00 +02:00
Patricia Lee
907e9e0bd3 mediatek: add support for Cetron CT3003
**Hardware specification:**

- SoC: MediaTek MT7981B 2x A53
- Flash: ESMT F50L1G41LB 128MB
- RAM: Nanya NT5CC128M16JR-EK 256MB
- Ethernet: 4 x 10/100/1000 Mbps
- Switch: MediaTek MT7531AE
- WiFi: MediaTek MT7976C
- Button: Reset, Mesh
- Power: DC 12V 1A
- UART: 3.3v, 115200n8
  | Layout:   |
  | :-------- |
  | <Antenna> |
  | VCC       |
  | GND       |
  | Tx        |
  | Rx        |

**Flash instructions:**

1. Rename `openwrt-mediatek-filogic-cetron_ct3003-squashfs-factory.bin` to `factory.bin`.
2. Upload the `factory.bin` using the device's Web interface.
3. Click the upgrade button and wait for the process to finish.
4. Access the OpenWrt interface using the same password.
5. Use the 'Restore' function to reset the firmware to its initial state.

**Notes:**

If you plan to recovery the stock firmware in the future, it's advisable
to connect the device via the serial port and enter failsafe mode to
back up all the MTD partitions before proceeding the steps above.

Signed-off-by: Patricia Lee <patricialee320@gmail.com>
2023-09-08 23:17:26 +02:00
Chen Minqiang
36746893ac mediatek: fix the name of buswidth to bus-width
Fix the issue of dts buswidth cannot be applied properly with spi driver.
Fix the name of buswidth to bus-width in dts in order to fit the format
in linux spi kernel[1] so that spi-tx-bus-width & spi-rx-bus-width can be
parsed properly.

[1] Documentation/devicetree/bindings/spi/spi-controller.yaml

Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
2023-09-05 15:40:43 +08:00
Hank Moretti
02214ab8dc mediatek: fix sysupgrade error for WR30U
The NMBM-Enabled layout did not use fit image,
it just need default process. So it was been removed in platform.sh.

It will fix sysupgrade error for xiaomi,mi-router-wr30u-112m-nmbm.

Signed-off-by: Hank Moretti <mchank9999@gmail.com>
2023-09-01 23:45:47 +02:00
Daniel Golle
a8cbee8e2d mediatek: mt7622: set DEVICE_DTC_ADDR for BPi-R64
Relocating the device tree is required for being apply to apply
device tree overylay at boot.

Fixes: 34bb33094a ("mediatek: use updated device tree overlay mechanism for BPi-R64")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-08-31 19:22:15 +01:00
Daniel Golle
8f5986355c mediatek: filogic: remove stray quote
When adapting the network configuration for MT7988 RFB a stray quote
was left in a script. Remove it to fix generating the default network
configuration.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-08-28 21:54:02 +01:00
Daniel Golle
f631c7bbb1 generic: sync MediaTek Ethernet driver with upstream
Import commits from upstream Linux replacing some downstream patches.
Move accepted patches from pending-{5.15,6.1} to backport-{5.15,6.1}.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-08-28 16:35:22 +01:00
Daniel Golle
a0f4eadf6a mediatek: add support for Ubiquiti UniFi 6 LR v3
Some recent models of the Ubiquiti Networks UniFi 6 LR access point
come with a RealTek RTL8211FS 1000M/100M/10M PHY instead of the
Aquantia AQR112 2500M/1000M/100M/10M PHY used in both v1 and v2. Add
build for this variant so we can support Ethernet with the PHY.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-08-28 16:35:22 +01:00
Daniel Golle
035a88ae55 mediatek: generate bootloader artifacts for mt7988_rfb
Switch to OpenWrt uImage.FIT bootmethod and include various bootloader
artifacts with the generated binaries.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-08-28 16:35:22 +01:00
Daniel Golle
3ef8760e87 mediatek: improve mt7981.dtsi
* re-factor WED components to boot fine also on limited loaders
 * add LEDs of integrated GE PHY

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-08-28 13:55:38 +01:00
Daniel Golle
9f8fde216d mediatek: filogic: improve pinctrl drivers
Set correct pull-type data and add additional uart groups for MT7981.
Assign functions to configure pin bias for MT7986.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-08-28 13:55:38 +01:00
Daniel Golle
2544dc34f2 mediatek: i2c: mt65xx: allow optional pmic clock
Using the I2C host controller on the MT7981 SoC requires 4 clocks to
be enabled. One of them, the pmic clk, is only enabled in case
'mediatek,have-pmic' is also set which has other consequences which
are not desired in this case.

Allow defining a pmic clk even in case the 'mediatek,have-pmic' propterty
is not present and the bus is not used to connect to a pmic, but may
still require to enable the pmic clock.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-08-28 13:55:38 +01:00
Daniel Golle
06a150aed7 mediatek: re-add dropped properties on BPi-R3
Unfortunately some device tree properties have slipped under the table
when switching from our downstream device tree.

Bring back 3W power for SFP cages and restore thermal trip points to
make sense again.

Fixes: 7a0ec001ff ("mediatek: sync MT7986 device trees with upstream")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-08-28 13:55:38 +01:00
John Audia
4b3e3c3fd7 kernel: bump 6.1 to 6.1.47
Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.1.47

All patches automatically rebased.

Build system: x86/64
Build-tested: x86/64/AMD Cezanne
Run-tested: x86/64/AMD Cezanne

Signed-off-by: John Audia <therealgraysky@proton.me>
2023-08-26 00:07:16 +02:00
David Bauer
6dc0675e5b mediatek: enable NMBM remapping for NWA50AX Pro UBI
Don't skip remapping of the UBI area for the ZyXEL NWA50AX Pro. This is
due to the kernel being loaded from the UBI partition by U-Boot.

Link: https://github.com/openwrt/openwrt/pull/13335

Signed-off-by: David Bauer <mail@david-bauer.net>
2023-08-25 21:42:31 +02:00
David Bauer
4c0fdad7ea mediatek: enable NWA50AX Pro eth LEDs
Enable the ethernet LED's on the ZyXEL NWA50AX Pro to show link-state as
well as activity.

Both LED's are configured pulsing.

AMBER | 10/100
GREEN | 1000
A+G   | 2500

Signed-off-by: David Bauer <mail@david-bauer.net>
2023-08-22 13:37:27 +02:00
Stefan Agner
4af06aaf33 mediatek: filogic: wax220: cleanup device tree
Fix compatible string to match what is supported upstream, fix alignment
and order MTD partitions according to offset.

Signed-off-by: Stefan Agner <stefan@agner.ch>
2023-08-22 13:37:27 +02:00
Stefan Agner
fa9d977f97 mediatek: filogic: wax220: support factory image
Enable building a factory image which can be flashed through the OEM
firmware's web interface. It seems that the web interface requires a
minimum file size of 10MiB, otherwise it will not accept the image.

The update image is a regular sysupgrade tarball packed in a Netgear
encrypted image. The Netgear encrypted image is the same as used in
WAX202 or WAX206, including the encryption keys and IV.

This adds a script which creates the rootfs_data volume on first
startup. This is required since the OEM firmware's sysupgrade scripts
do not create such a paritition. Note that any script ordered after
70_initramfs_test will not get executed on initramfs. Hence this new
script 75_rootfs_prepare won't create the rootfs_data volume when
using the recovery initramfs.

Also, this deletes the kernel_backup and rootfs_backup volumes in case
we have to create the rootfs_data volumes. This makes sure that
OpenWrt is the actual backup firmware instead of the stock firmware.

References in WAX220 GPL source:
https://www.downloads.netgear.com/files/GPL/WAX220-V1.0.2.8-gpl-src.tar.gz

* package/base-files/files/lib/upgrade/nand.sh:186
  Creation of rootfs_data is disabled

* Uboot-upstream/board/mediatek/common/ubi_helper.c
  Automatic creation of UBI backup volumes

Signed-off-by: Stefan Agner <stefan@agner.ch>
2023-08-22 13:37:27 +02:00
David Bauer
c35ff41ccc mediatek: add missing packages for Acer Predator W6
Add missing packages for creating the overlay filesystem.

Signed-off-by: David Bauer <mail@david-bauer.net>
2023-08-22 12:24:34 +02:00
Bjørn Mork
6cc14bf66a filogic: support Telenor branded ZyXEL EX5700
Telenor quirks
--------------
The operator specific firmware running on the Telenor branded
ZyXEL EX5700 includes U-Boot modifications affecting the OpenWrt
installation.

Notable changes to U-Boot include
- environment is stored in RAM and reset to defaults when power
  cycled
- dual partition scheme with "nomimal" or "rescue" systems, falling
  back to "rescue" unless the OS signals success in 3 attempts
- several runtime additions to the device-tree

Some of these modifications have side effects requiring workarounds
- U-Boot modifies /chosen/bootargs in an unsafe manner, and will crash
  unless this node exists
- U-Boot verifies that the selected rootfs UBI volume exists, and
  refuses to boot if it doesn't. The chosen "rootfs" volume must contain
  a squashfs signature even for tftp or initramfs booting.
- U-Boot parses the "factoryparams" UBI volume, setting the "ethaddr"
  variable to the label mac.  But "factoryparams" does not always
  exist.  Instead there is a "RIP" volume containing all the factory
  data.  Copying the "RIP" volume to  "factoryparams" will fix this

Hardware
--------
SOC:   MediaTek MT7986
RAM:   1GB DDR4
FLASH: 512MB SPI-NAND (Mikron xxx)
WIFI:  Mediatek MT7986 802.11ax 5 GHz
       Mediatek MT7916 DBDC 802.11ax 2.4 + 6 GHz
ETH:   MediaTek MT7531 Switch + SoC
       3 x builtin 1G phy (lan1, lan2, lan3)
       2 x MaxLinear GPY211C 2.5 N-Base-T phy (lan4, wan)
USB:   1 x USB 3.2 Enhanced SuperSpeed port
UART:  3V3 115200 8N1 (Pinout: GND KEY RX TX VCC)

Installation
------------
1. Download the OpenWrt initramfs image. Copy the image to a TFTP server
   reachable at 192.168.1.2/24. Rename the image to C0A80101.img.

2. Connect the TFTP server to lan1, lan2 or lan3. Connect to the serial
   console, Interrupt the autoboot process by pressing ESC when prompted.

3. Download and boot the OpenWrt initramfs image.

   $ env set uboot_bootcount 0
   $ env set firmware nominal
   $ tftpboot
   $ bootm

4. Wait for OpenWrt to boot. Transfer the sysupgrade image to the device
   using scp and install using sysupgrade.

   $ sysupgrade -n <path-to-sysupgrade.bin>

Missing features
----------------

- The "lan1", "lan2" and "lan3" port LEDs are driven by the switch but
  OpenWrt does not correctly configure the output.
- The "lan4" and "wan" port LEDs are driven by the GPH211C phys and
  not configured by OpenWrt.

Signed-off-by: Bjørn Mork <bjorn@mork.no>
2023-08-20 01:14:06 +02:00
Bjørn Mork
1dd1ac2c35 mediatek: filogic: set wan label in preinit
Implement the functionality of
target/linux/ramips/patches-5.15/700-net-ethernet-mediatek-support-net-labels.patch
in userspace, since the driver patch has been rejected as a generic solution:
https://github.com/openwrt/openwrt/pull/11435

Signed-off-by: Bjørn Mork <bjorn@mork.no>
2023-08-20 01:14:06 +02:00
Daniel Golle
0454691960 mediatek: filogic: mt7988: mark RTC clock as critical
A dependency of the MT7988 MMC host controller on the SoC's RTC clock
being running has been discovered. Mark RTC clock as critical to fix
MMC host on MT7988.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-08-13 15:01:36 +01:00
John Audia
64782497db kernel: bump 5.15 to 5.15.126
1. Disable unneeded errata Kconfig symbols
2. Update kernel

Changelog: https://lore.kernel.org/stable/2023081111-unlocking-synopsis-d7d5@gregkh/

All patches automatically rebased.

Build system: x86_64
Build-tested: ramips/tplink_archer-a6-v3
Run-tested: ramips/tplink_archer-a6-v3

Signed-off-by: John Audia <therealgraysky@proton.me>
2023-08-13 13:03:43 +02:00
John Audia
1e0ee72b72 kernel: bump 6.1 to 6.1.44
Changelog: https://lore.kernel.org/stable/2023080822-repost-unfiled-2f01@gregkh/

All patches automatically rebased.

Build system: x86/64
Build-tested: x86/64/AMD Cezanne, filogic/xiaomi_redmi-router-ax6000-ubootmod
Run-tested: x86/64/AMD Cezanne, filogic/xiaomi_redmi-router-ax6000-ubootmod

Signed-off-by: John Audia <therealgraysky@proton.me>
2023-08-09 20:39:20 -04:00
John Audia
549e710fc0 kernel: bump 6.1 to 6.1.43
1. Disable Ampere errata fix in target/linux/generic/config-6.1

2. Update kernel Changelog: https://lore.kernel.org/stable/2023061431-modular-data-8489@gregkh/

Manually rebased:
        bcm27xx/patches-6.1/950-0359-xhci-quirks-add-link-TRB-quirk-for-VL805.patch
        bcm27xx/patches-6.1/950-0362-usb-xhci-add-VLI_TRB_CACHE_BUG-quirk.patch
        bcm27xx/patches-6.1/950-0390-usb-xhci-add-a-quirk-for-Superspeed-bulk-OUT-transfe.patch
        bcm27xx/patches-6.1/950-0469-usb-xhci-add-XHCI_VLI_HUB_TT_QUIRK.patch
        bcm27xx/patches-6.1/950-0520-xhci-constrain-XHCI_VLI_HUB_TT_QUIRK-to-old-firmware.patch

All other patches automatically rebased.

Build system: x86/64
Build-tested: x86/64/AMD Cezanne, filogic/xiaomi_redmi-router-ax6000-ubootmod
Run-tested: x86/64/AMD Cezanne, filogic/xiaomi_redmi-router-ax6000-ubootmod

Signed-off-by: John Audia <therealgraysky@proton.me>
2023-08-09 20:39:20 -04:00
John Audia
daed3322d3 kernel: bump 5.15 to 5.15.125
1. Add new symbols to generic config
2. Bump kernel
   Changelog: https://lore.kernel.org/stable/2023080818-groin-gradient-a031@gregkh/

   All patches automatically rebased.

Signed-off-by: John Audia <therealgraysky@proton.me>
2023-08-09 22:06:24 +02:00
John Audia
81c1172c36 kernel: bump 5.15 to 5.15.124
Changelog: https://lore.kernel.org/stable/2023080341-curliness-salary-4158@gregkh/

1. Needed to make a change to to package/kernel/linux/modules/netsupport.mk
   due to upstream moving vxlan to its own directory[1].  @john-tho suggested
   using the the 6.1 xvlan FILES to circumvent.
2. All patches automatically rebased.

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.124&id=77396fa9096abdbfbb87d63e73ad44d5621cf103

Signed-off-by: John Audia <therealgraysky@proton.me>
2023-08-09 22:06:23 +02:00
David Bauer
7e7eb5312d mediatek: add support for Acer Predator W6
Hardware
--------
SOC:   MediaTek MT7986A
RAM:   1GB DDR4
FLASH: 4GB eMMC
WiFi:  2x2 2.4 GHz 802.11 b/g/n/ax MT7916 DBDC
       4x4 5 GHz   802.11 a/n/ac/ax MT7986
       2x2 6 GHz   802.11ax MT7916 DBDC
ETH:   4x LAN 1Gbit/s (MT7531)
       1x WAN 2.5Gbit/s (GPY211)
BTN:   RESET, WPS
LED:   Antenna LEDs (GPIO)
       Mood-LED (Kinetic KTD2601) - unsupported
UART:  Header nest to USB port - 3V3 115200 8N1
       [BUTTON] GND - RX - TX [USB]

Installation
------------

1. Connect to the device using serial console.

2. Interrupt the Autoboot process when promted by sending '0' twice.

3. Serve the OpenWrt initramfs image using TFTP at 192.168.1.66. Name
   the image "predator.bin" and conenct the TFTP server to the routers
   LAN port.

4. Configure U-Boot to allow loading unsigned images from MMC

   $ setenv bootcmd 'mmc read 0x40000000 0x00004400 0x0010000;
     fdt addr $(fdtcontroladdr); fdt rm /signature; bootm 0x40000000';
     saveenv

5. Transfer the image from U-Boot

   $ setenv serverip 192.168.1.66; setenv ipaddr 192.168.1.1;
     tftpboot 0x46000000 predator.bin; fdt addr $(fdtcontroladdr);
     fdt rm /signature; bootm

6. Wait for OpenWrt to boot

7. Transfer the OpenWrt sysupgrade image to the router using scp.

8. Install OpenWrt using sysupgrade.

Signed-off-by: David Bauer <mail@david-bauer.net>
2023-08-05 18:42:45 +02:00
Daniel Golle
1eb67cb070 mediatek: filogic: restore non-const type in pinctrl-mt7988 driver
When building with Linux 5.15 the 'const' type results in warnings.
Restore the original non-const type in those cases.

Fixes: 36d0aa9c2d ("mediatek: filogic: sync pinctrl-mt7988 with MediaTek SDK")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-08-03 23:34:22 +01:00
Daniel Golle
64b99802a6 mediatek: filogic: update MT7988 device tree
* move ethernet to mt7988a.dtsi
 * move switch definition to mt7988a.dtsi
 * add PHY LEDs

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-08-03 15:47:51 +01:00
Daniel Golle
36d0aa9c2d mediatek: filogic: sync pinctrl-mt7988 with MediaTek SDK
Update pinctrl driver for the MT7988 with driver from mtk-openwrt-feeds.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-08-03 15:47:51 +01:00
Daniel Golle
dc4aafb309 mediatek: filogic: enable driver for MediaTek XS-PHY
Enable driver for MediaTek SuperSpeedPlus XS-PHY transceiver for the
USB3.1 GEN2 controllers found in the MT7988 SoC.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-07-31 18:05:22 +01:00
John Audia
8590531048 kernel: bump 5.15 to 5.15.123
Manually rebased:
	bcm4908/patches-5.15/071-v6.1-0001-net-broadcom-bcm4908_enet-handle-EPROBE_DEFER-when-g.patch
	bcm53xx/patches-5.15/180-usb-xhci-add-support-for-performing-fake-doorbell.patch
	ipq40xx/patches-5.15/902-dts-ipq4019-ap-dk04.1.patch[*]

Removed upstreamed:
	backport-5.15/735-v6.5-net-bgmac-postpone-turning-IRQs-off-to-avoid-SoC-han.patch[1]
	backport-5.15/817-v6.5-01-leds-trigger-netdev-Recheck-NETDEV_LED_MODE_LINKUP-o.patch[2]
	pending-5.15/143-jffs2-reduce-stack-usage-in-jffs2_build_xattr_subsys.patch[3]
	pending-5.15/160-workqueue-fix-enum-type-for-gcc-13.patch[4]
	bcm53xx/patches-5.15/036-v6.5-0003-ARM-dts-BCM5301X-Drop-clock-names-from-the-SPI-node.patch[5]
	bcm53xx/patches-5.15/036-v6.5-0015-ARM-dts-BCM5301X-fix-duplex-full-full-duplex.patch[6]

All other patches automatically rebased.

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.123&id=02474292a44205c1eb5a03634ead155a3c9134f4
2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.123&id=86b93cbfe104e99fd3d25a49748b99fb88101573
3. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.123&id=79b9ab357b6f5675007f4c02ff8765cbd8dc06a2
4. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.123&id=d528faa9e828b9fc46dfb684a2a9fd8c2e860ed8
5. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.123&id=5899bc4058e89d5110a23797ff94439c53b77c25
6. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.123&id=95afd2c7c7d26087730dc938709e025a303e5499

Build system: x86/64
Build-tested: ramips/tplink_archer-a6-v3
Run-tested: ramips/tplink_archer-a6-v3

Co-authored-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John Audia <therealgraysky@proton.me>
[rebased ipq40xx/patches-5.15/902-dts-ipq4019-ap-dk04.1.patch ]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2023-07-30 18:02:47 +02:00
Petr Štetiar
edd146c920
mediatek: filogic: fix broken sysupgrade script
Changes introduced in commit 54dc1cde48 ("mediatek: filogic: add
support for Xiaomi WR30U") missed to end the case item with mandatory
`;;` which lead to a broken sysupgrade.

Fixes: 54dc1cde48 ("mediatek: filogic: add support for Xiaomi WR30U")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2023-07-28 08:24:11 +02:00
Hank Moretti
dcdcfc1511 mediatek: filogic: add specific layout for WR30U
Because this device enable NMBM by default, most users use custom
U-Boot with NMBM-Enabled in Chinese forums.

This layout is the same as the ubootmod layout but enabling NMBM.

Signed-off-by: Hank Moretti <mchank9999@gmail.com>
2023-07-27 13:46:26 +02:00
Hank Moretti
54dc1cde48 mediatek: filogic: add support for Xiaomi WR30U
Hardware specification:
  SoC: MediaTek MT7981B 2x A53
  Flash: ESMT F50L1G41LB 128MB
  RAM: NT52B128M16JR-FL 256MB
  Ethernet: 4x 10/100/1000 Mbps
  Switch: MediaTek MT7531AE
  WiFi: MediaTek MT7976C
  Button: Reset, Mesh
  Power: DC 12V 1A

Flash instructions:

1. Get ssh access
   Check this link: https://forum.openwrt.org/t/openwrt-support-for-xiaomi-ax3000ne/153769/22

2. Backup import partitions
   ```
   dev:    size   erasesize  name
   mtd1: 00100000 00020000 "BL2"
   mtd2: 00040000 00020000 "Nvram"
   mtd3: 00040000 00020000 "Bdata"
   mtd4: 00200000 00020000 "Factory"
   mtd5: 00200000 00020000 "FIP"
   mtd8: 02200000 00020000 "ubi"
   mtd9: 02200000 00020000 "ubi1"
   mtd12: 00040000 00020000 "KF"

   ```

   Use these commands blow to backup your stock partitions.
   ```
   nanddump -f /tmp/BL2.bin /dev/mtd1
   nanddump -f /tmp/Nvram.bin /dev/mtd2
   nanddump -f /tmp/Bdata.bin /dev/mtd3
   nanddump -f /tmp/Factory.bin /dev/mtd4
   nanddump -f /tmp/FIP.bin /dev/mtd5
   nanddump -f /tmp/ubi.bin /dev/mtd8
   nanddump -f /tmp/KF.bin /dev/mtd12
   ```
   Then, transfer them to your computer via scp, netcat, tftp
   or others and keep them in a safe place.

3. Setup Nvram
   Get the current stock: `cat /proc/cmdline`

   If you find `firmware=0` or `mtd=ubi`, use these commands:
   ```
   nvram set boot_wait=on
   nvram set uart_en=1
   nvram set flag_boot_rootfs=1
   nvram set flag_last_success=1
   nvram set flag_boot_success=1
   nvram set flag_try_sys1_failed=0
   nvram set flag_try_sys2_failed=0
   nvram commit
   ```

   If you find `firmware=1` or `mtd=ubi1`, use these commands:
   ```
   nvram set boot_wait=on
   nvram set uart_en=1
   nvram set flag_boot_rootfs=0
   nvram set flag_last_success=0
   nvram set flag_boot_success=1
   nvram set flag_try_sys1_failed=0
   nvram set flag_try_sys2_failed=0
   nvram commit
   ```

4. Flash stock-initramfs-factory.ubi
   If you find `firmware=0` or `mtd=ubi`:
   `ubiformat /dev/mtd9 -y -f /tmp/stock-initramfs-factory.ubi`

   If you find `firmware=1` or `mtd=ubi1`:
   `ubiformat /dev/mtd8 -y -f /tmp/stock-initramfs-factory.ubi`

   Then reboot your router, it should boot to the openwrt
   initramfs system now.

5. Setup uboot-env
   Now it will be setup automatically in upgrade process,
   you can skip this step.

   If your `fw_setenv` did not work, you need run this command:
   `echo "/dev/mtd1 0x0 0x10000 0x20000" > /etc/fw_env.config`

   Then setup uboot-env:
   ```
   fw_setenv boot_wait on
   fw_setenv uart_en 1
   fw_setenv flag_boot_rootfs 0
   fw_setenv flag_last_success 1
   fw_setenv flag_boot_success 1
   fw_setenv flag_try_sys1_failed 8
   fw_setenv flag_try_sys2_failed 8
   fw_setenv mtdparts "nmbm0:1024k(bl2),256k(Nvram),256k(Bdata),
   2048k(factory),2048k(fip),256k(crash),256k(crash_log),
   34816k(ubi),34816k(ubi1),32768k(overlay),12288k(data),256k(KF)"
   ```

6. Flash stock-squashfs-sysupgrade.bin
   Use shell command:
   `sysupgrade -n /tmp/stock-squashfs-sysupgrade.bin`
   Or go to luci web.

If you need to change to Openwrt U-Boot layout, do next. If you
do not need, please ignore it.

Change to OpenWrt U-Boot:

1. Flash ubootmod-initramfs-factory.ubi
   Check mtd partitions: `cat /proc/mtd`
   ```
   mtd7: 00040000 00020000 "KF"
   mtd8: 02200000 00020000 "ubi_kernel"
   mtd9: 04e00000 00020000 "ubi"
   ```

   Run following command:
   `ubiformat /dev/mtd8 -y -f /tmp/ubootmod-initramfs-factory.ubi`
   Then reboot your router, it should boot to the openwrt initramfs
   system now.

2. Check mtd again
   ```
   mtd7: 00040000 00020000 "KF"
   mtd8: 07000000 00020000 "ubi"
   ```
   Make sure mtd8 is ubi.

3. Install kmod-mtd-rw
   Run command: `opkg update && opkg install kmod-mtd-rw`
   Or get it in openwrt server, or build it yourself, then install
   it manually

   Then run this command:
   `insmod /lib/modules/$(uname -r)/mtd-rw.ko i_want_a_brick=1`

4. Clean up pstore
   Run Command: `rm -f /sys/fs/pstore/*`

5. Format ubi and create new ubootenv volume
   ```
   ubidetach -p /dev/mtd8; ubiformat /dev/mtd8 -y; ubiattach -p /dev/mtd8
   ubimkvol /dev/ubi0 -n 0 -N ubootenv -s 128KiB
   ubimkvol /dev/ubi0 -n 1 -N ubootenv2 -s 128KiB
   ```

6. (Optional) Add recovery boot feature.
   ```
   ubimkvol /dev/ubi0 -n 2 -N recovery -s 10MiB
   ubiupdatevol /dev/ubi0_2 /tmp/ubootmod-initramfs-recovery.itb
   ```

7. Flash Openwrt U-Boot
   ```
   mtd write /tmp/ubootmod-preloader.bin BL2
   mtd write /tmp/ubootmod-bl31-uboot.fip FIP
   ```

6. Flash ubootmod-squashfs-sysupgrade.itb
   Use shell command:
   `sysupgrade -n /tmp/ubootmod-squashfs-sysupgrade.itb`
   Or go to luci web.

Now everything is done, Enjoy!

Go Back to stock from Openwrt U-Boot:

1. Force flash ubootmod-initramfs-recovery.itb
   Use shell command:
   `sysupgrade -F -n /tmp/ubootmod-initramfs-recovery.itb`
   Or go to luci web.
   Then it should boot to the openwrt initramfs system now.

2. Format ubi and Nvram
   ```
   ubidetach -p /dev/mtd8; ubiformat /dev/mtd8 -y; ubiattach -p /dev/mtd8
   mtd erase Nvram
   ```

3. Install kmod-mtd-rw
   Run command: `opkg update && opkg install kmod-mtd-rw`
   Or get it in openwrt server, or build it yourself, then install
   it manually

   Then run this command:
   `insmod /lib/modules/$(uname -r)/mtd-rw.ko i_want_a_brick=1`

4. Flash stock U-Boot and ubi
   ```
   mtd write /tmp/BL2.bin BL2
   mtd write /tmp/FIP.bin FIP
   mtd write /tmp/ubi.bin ubi
   ```
   Then reboot your router, waiting it finished rollback in minutes.

Go Back to stock from stock layout Openwrt:
   Just run command: `ubiformat /dev/mtd8 -y -f /tmp/ubi.bin`
   Then reboot your router, waiting it finished rollback in minutes.

Notes:
1. Openwrt U-Boot and ubootmod openwrt did not enable NMBM.
   Please make your backup safe.

Signed-off-by: Hank Moretti <mchank9999@gmail.com>
2023-07-27 13:46:16 +02:00
John Audia
d91f38a99e kernel: bump 6.1 to 6.1.40
Removed upstreamed:
	generic/backport-6.1/701-v6.5-net-bgmac-postpone-turning-IRQs-off-to-avoid-SoC-han.patch[1]
	generic/pending-6.1/160-workqueue-fix-enum-type-for-gcc-13.patch[2]
	qualcommax/patches-6.1/0022-v6.5-soc-qcom-mdt_loader-Fix-unconditional-call-to-scm_pa.patch[3]

Manually rebased:
	bcm27xx/patches-6.1/950-0359-xhci-quirks-add-link-TRB-quirk-for-VL805.patch
	bcm27xx/patches-6.1/950-0362-usb-xhci-add-VLI_TRB_CACHE_BUG-quirk.patch
	bcm27xx/patches-6.1/950-0390-usb-xhci-add-a-quirk-for-Superspeed-bulk-OUT-transfe.patch
	bcm27xx/patches-6.1/950-0469-usb-xhci-add-XHCI_VLI_HUB_TT_QUIRK.patch
	bcm53xx/patches-6.1/180-usb-xhci-add-support-for-performing-fake-doorbell.patch

All other patches automatically rebased.

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.40&id=685b57a1221c38ec8b456f968264d2496715820c
2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.40&id=2d57a1590f4d8c516f5aaf8fd5bb4f52d67275d8
3. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.40&id=33f8dff6e1cbba5c2ec85fa5649c0a759a7e685c

Build system: x86/64, filogic/xiaomi_redmi-router-ax6000-ubootmod
Build-tested: x86/64, filogic/xiaomi_redmi-router-ax6000-ubootmod
Run-tested: x86/64

Signed-off-by: John Audia <therealgraysky@proton.me>
2023-07-25 00:24:21 +02:00
John Audia
fec22f8375 kernel: bump 6.1 to 6.1.39
Removed upstreamed:
	generic/backport-6.1/803-v6.5-01-leds-trigger-netdev-Recheck-NETDEV_LED_MODE_LINKUP-o.patch[1]
	generic/pending-6.1/143-jffs2-reduce-stack-usage-in-jffs2_build_xattr_subsys.patch[2]
	bcm27xx/patches-6.1/950-0034-drm-bridge-Introduce-pre_enable_upstream_first-to-al.patch[3]
	bcm27xx/patches-6.1/950-0439-nvmem-Use-NVMEM_DEVID_AUTO.patch[4]
	bcm4908/patches-6.1/040-mtd-parsers-refer-to-ARCH_BCMBCA-instead-of-ARCH_BCM.patch[5]
	bcm53xx/patches-6.1/031-v6.5-0003-ARM-dts-BCM5301X-Drop-clock-names-from-the-SPI-node.patch[6]
	bcm53xx/patches-6.1/031-v6.5-0015-ARM-dts-BCM5301X-fix-duplex-full-full-duplex.patch[7]
	mediatek/patches-6.1/351-cpufreq-mediatek-correct-voltages-for-MT7622-and-MT7.patch[8]
	qualcommax/patches-6.1/0008-v6.2-clk-qcom-reset-support-resetting-multiple-bits.patch[9]

Manually rebased:
	bcm27xx/patches-6.1/950-0035-drm-panel-Add-prepare_upstream_first-flag-to-drm_pan.patch
	bcm27xx/patches-6.1/950-0404-drm-panel-panel-ilitek9881c-Add-prepare_upstream_fir.patch
	bcm27xx/patches-6.1/950-0699-Bluetooth-hci_sync-Add-fallback-bd-address-prop.patch
	mediatek/patches-6.1/350-21-cpufreq-mediatek-Add-support-for-MT7988.patch

All other patches automatically rebased.

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.39&id=ab0bd172d6289310a05a0cd15e1432e828d386ae
2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.39&id=6df680709d901346831ef8f221cc90a42062c526
3. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.39&id=5044e5f2511c9afdf9880d2bb6b9d37dfc345dac
4. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.39&id=e27948f329f7e02591ed1feb9a7710c2ccf89a83
5. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.39&id=ad2928e7f3f6120a0bd18aa1056b3b24068027c5
6. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.39&id=2b55a985727833f37c39911f34096b3fdf2a367d
7. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.39&id=90d4c487cd658b51212eb65ae804ab11af193672
8. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.39&id=7e3ee25e8c7c7be1eacdfc6d9f5f0e550a2af241
9. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.39&id=b20854ef6c4955be3310975a72f02d92cb01d6d4

Build system: x86/64
Build-tested: x86/64
Run-tested: x86/64

Co-authored-by: Hauke Mehrtens <hauke@hauke-m.de>
Co-authored-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: John Audia <therealgraysky@proton.me>
[ rebase bcm27xx and mediatek patches, refresh commit description ]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
[ minor fixup to bcm27xx patches, refresh commit description ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2023-07-25 00:24:21 +02:00
David Bauer
36f7ececc2 mediatek: add missing SPDX header
Signed-off-by: David Bauer <mail@david-bauer.net>
2023-07-22 17:41:22 +02:00
Daniel Golle
b1d10e0174 mediatek: filogic: set DEVICE_DTS_LOADADDR for BPi-R3
U-Boot complains that the overlayed DT needs relocation, so set
DEVICE_DTS_LOADADDR to have it relocated.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-07-22 12:31:31 +01:00
David Bauer
f0445746f6 mediatek: add support for ZyXEL NWA50AX Pro
Hardware
--------
CPU:    Mediatek MT7981
RAM:    512M DDR4
FLASH:  256M NAND
ETH:    MaxLinear GPY211 (2.5GbE N Base-T)
WiFi:   Mediatek MT7981 (2.4GHz 2T2R:2 5GHz 3T3R:2 802.11ax)
BTN:    1x Reset
LED:    1x Multi-Color

UART Console
------------
Available below the rubber cover next to the ethernet port.

Settings: 115200 8N1

Layout:

<12V> <LAN> GND-RX-TX-VCC

Logic-Level is 3V3. Don't connect VCC to your UART adapter!

Installation Web-UI
-------------------
Upload the Factory image using the devices Web-Interface.

As the device uses a dual-image partition layout, OpenWrt can only
installed on Slot A. This requires the current active image prior
flashing the device to be on Slot B.

In case this is not the case, OpenWrt will boot only one time, returning
to the ZyXEL firmware the second boot.

If this happens, first install a ZyXEL firmware upgrade of any version
and install OpenWrt after that.

Installation TFTP / Recovery
----------------------------
This installation routine is especially useful in case of a bricked
device.

Attach to the UART console header of the device. Interrupt the boot
procedure by pressing Enter.

The bootloader has a reduced command-set available from CLI, but more
commands can be executed by abusing the atns command.

Boot a OpenWrt initramfs image available on a TFTP server at
192.168.1.66. Rename the image to nwa50axpro-openwrt-initramfs.bin.

 $ atnf nwa50axpro-openwrt-initramfs.bin
 $ atna 192.168.1.88
 $ atns "192.168.1.66; tftpboot; setenv fdt_high 0xffffffffffffffff;
   bootm"

Upon booting, set the booted image to the correct slot:

 $ zyxel-bootconfig /dev/mtd9 get-status
 $ zyxel-bootconfig /dev/mtd9 set-image-status 0 valid
 $ zyxel-bootconfig /dev/mtd9 set-active-image 0

Copy the OpenWrt sysupgrade image to the device using scp.
Write the sysupgrade image to NAND using sysupgrade.

 $ sysupgrade -n image.bin

Signed-off-by: David Bauer <mail@david-bauer.net>
2023-07-21 20:28:13 +02:00
Daniel Golle
712fa3eff8 mediatek: replace hack for MaxLinear 2.5G PHY
Replace hack with proper patch also for Linux 5.15.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-07-08 17:36:19 +01:00
Daniel Golle
f321a49fd5 mediatek: dts: mt7988a: remove boottrap hack
The PHY driver now uses regmap created from pio syscon, we no longer
need the boottrap device.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-07-08 17:36:19 +01:00
Daniel Golle
9fac590096 mediatek: use backported Ethernet PHY driver also for 5.15
Backport in-SoC Gigabit Ethernet PHY driver instead of carrying the
driver in files-5.15.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-07-08 17:36:19 +01:00
Daniel Golle
1f1e0b1144 mediatek: dts: mt7988a: wire-up mediatek,pio for PHY LEDs
The PHY driver needs to read a register containing the values of the
bootstrap pins (which happen to be the PHY LEDs) to determine the LED
polarities. Allow regmap access to first pinctrl bank by adding the
'syscon' compatible, and reference the pinctrl in the MDIO bus where
the PHY driver will look for it.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-07-08 16:36:49 +01:00
Christian Svensson
c170fc78ba kernel: remove CRYPTO_BLAKE2S from all >=5.15
This option was removed from upstream kernel back in 2022.
See commits:
 2d16803c562ecc644803d42ba98a8e0aef9c014e (>=6.0)
 3dd33a09f5dc12ccb0902923c4c784eb0f8c7554 (>=5.15.61 backport)

Signed-off-by: Christian Svensson <blue@cmd.nu>
2023-07-08 16:54:01 +02:00
John Audia
0dc0504fc8 kernel: bump 5.15 to 5.15.120
All patches automatically rebased.

Build system: x86_64
Build-tested: ramips/tplink_archer-a6-v3, filogic/xiaomi_redmi-router-ax6000-ubootmod
Run-tested: ramips/tplink_archer-a6-v3, filogic/xiaomi_redmi-router-ax6000-ubootmod

Signed-off-by: John Audia <therealgraysky@proton.me>
2023-07-07 17:07:26 +02:00
Daniel Golle
1321007e1f mediatek: expose testing Linux 6.1 testing kernel
Set KERNEL_TESTING_PATCHVER:=6.1 to allow building all subtargets with
Linux 6.1.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-07-07 14:01:39 +02:00
Daniel Golle
30d38d7541 mediatek: adapt kernel configuration for Linux 6.1
Update kernel configuration to build Linux 6.1 for all subtargets.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-07-07 14:01:39 +02:00
Daniel Golle
775fd1fc85 mediatek: copy config-5.15 to config-6.1 for all subtargets
To ease review, first copy all subtargets' kernel config-5.15 to the
to-be-adapted config-6.1.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-07-07 14:01:39 +02:00
Daniel Golle
659f4a13dd mediatek: adapt files and patches for Linux 6.1
With Linux 6.1 many of our downstream patches and out-of-tree files
can be removed or at least replaced by backported upstream commits.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
[fix CMDLINE_OVERRIDE for arm64]
Signed-off-by: Bjørn Mork <bjorn@mork.no>
2023-07-07 14:01:39 +02:00
Daniel Golle
d85438f454 mediatek: copy patches and files for Linux 6.1
First step only copies patches-5.15 and files-5.15 to
patches-6.1 and files-6.1 respectively.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-07-07 14:01:39 +02:00
Daniel Golle
0c5605b70c mediatek: prepare old rtk switch driver for use with Linux 6.1
The old RealTek RTL8367S switch driver which is used for some MT7622
devices needs to be modified to no longer free the GPIO after reset
has completed.
This is due to Linux 5.19 removing devm_gpio_free via commit
2b038e786f83 ("gpiolib: devres: Get rid of unused devm_gpio_free()")

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-07-07 14:01:39 +02:00
David Bauer
92eec257dd mediatek: define NMBM management region for WAX220
The NETGEAR WAX220 employs NMBM on SPI-NAND. In order to avoid dealing
with invalid factory data, enable NMBM in the area preceding the UBI
volume.

Signed-off-by: David Bauer <mail@david-bauer.net>
2023-07-02 01:06:08 +02:00
Chukun Pan
e78d1a06c8 mediatek: filogic: add H3C Magic NX30 Pro support
Hardware specification:
  SoC: MediaTek MT7981B 2x A53
  Flash: W25N01GVZEIG 128MB
  RAM: NT5CB128M16JR-FL 256MB
  Ethernet: 4x 10/100/1000 Mbps
  Switch: MediaTek MT7531AE
  WiFi: MediaTek MT7976C
  Button: Reset, WPS
  Power: DC 12V 1A

Flash instructions:
  1. PC run command: "telnet 192.168.124.1 99"
     Username: H3C, password is the web login
     password of the router.
  2. Download preloader.bin and bl31-uboot.fip
  3. PC run command: "python3 -m http.server 80"
  4. Download files in the telnet window:
     "wget http://192.168.124.xx/xxx.bin"
     Replace xx with your PC's IP and
     the preloader.bin and bl31-uboot.fip.
  5. Flushing openwrt's uboot:
     "mtd write xxx-preloader.bin BL2"
     "mtd write xxx-bl31-uboot.fip FIP"
  6. Connect to the router via the Lan port,
     set a static ip of your PC.
     (ip 192.168.1.254, gateway 192.168.1.1)
  7. Download initramfs image, reboot router,
     waiting for tftp recovery to complete.
  8. After openwrt boots up, perform sysupgrade.

Note:
  1. The u-boot-env partition on mtd is empty,
     OEM stores their env on ubi:u-boot-env.
  2. Back up all mtd partitions before flashing.

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
2023-07-01 15:13:08 +02:00
Wenli Looi
73de41898f mediatek: add support for Netgear EX6250v2 series
Netgear EX6250v2, EX6400v3, EX6410v2, EX6470 are wall-plug 802.11ac
(Wi-Fi 5) extenders. Like other MT7629 devices, Wi-Fi does not work
currently as there is no driver.

Related: https://github.com/openwrt/openwrt/pull/5084

For future reference, 2.4GHz MAC = LAN+1, 5GHz MAC = LAN+2.

Specifications:
* MT7629, 256 MiB RAM, 16 MiB SPI NOR
* MT7761N (2.4GHz) / MT7762N (5GHz) - no driver
* Ethernet: 1 port 10/100/1000
* UART: 115200 baud (labeled on board)

Installation:
* Flash the factory image through the stock web interface, or TFTP to
  the bootloader. NMRP can be used to TFTP without opening the case.
* After installation, perform a factory reset. Wait for the device to
  boot, then hold the reset button for 10 seconds. This is needed
  because sysupgrade in the stock firmware will attempt to preserve its
  configuration using sysupgrade.tgz.
  See https://github.com/openwrt/openwrt/pull/4182

Revert to stock firmware:
* Flash the stock firmware to the bootloader using TFTP/NMRP.

Signed-off-by: Wenli Looi <wlooi@ucalgary.ca>
2023-07-01 14:42:11 +02:00
Wenli Looi
0a1ebccc87 image: add additional fields to Netgear encrypted image
These fields are used for EAX12 and EX6250v2 series, and perhaps other
devices. Compatibility is preserved with the WAX202 and WAX206.

In addition, adds the related vars to DEVICE_VARS so that the variables
work correctly with multiple devices.

References in GPL source:
https://www.downloads.netgear.com/files/GPL/EAX12_EAX11v2_EAX15v2_GPL_V1.0.3.34_src.tar.gz

* tools/imgencoder/src/gj_enc.c
  Contains code that generates the encrypted image.

Signed-off-by: Wenli Looi <wlooi@ucalgary.ca>
2023-07-01 14:42:11 +02:00