Expand kernel partition size on WSR-2533DHP2 for the kernel larger than
4 MiB.
To prevent upgrading from old firmware before this commit, bump the
compat version to 1.1 and add a message for forced sysupgrade using
factory-uboot.bin image.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Update LED and key nodes with newer DeviceTree bindings for WSR-2533DHP2.
- LED
- use led-[0-9] for node name of LEDs
- add "color" and "function" properties
- drop default-state = "on" from green:power LED
- this LED will be turned on by led-running alias
- key
- drop unnecessary poll-interval property
- use key-[0-9] for node name of keys
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
A bug report in the forum found that the MR70X lists four LAN ports in LuCI
while it has only three. This adds the device to the network setup file
to fix the issue.
Identified-by: Forum User "Lexeyko"
Signed-off-by: Andreas Böhler <dev@aboehler.at>
```
Specifications:
* CPU: Qualcomm IPQ8072A, SoC Version: 2.0, Quad core Cortex-A53 1.6896 GHz
* RAM: 1 GiB of DDR4 600 MHz
* Flash: NAND 2x256 MiB (Macronix MX30UF2G18AC)
* 4 RGB LEDs: Power, LAN, 2.4GHz and 5GHz
* UART: Two 4-pin unpopulated headers under the LEDs.
Use the header closest to LED 4 and 5.
They are marked with a white stroke.
TX RX GND, beginning from "4". 115200n8.
Lan:
* One 100/1000/2.5GBASE-T Gigabit Ethernet (QCA8081)
Wlan:
* 4x4 in 2.4GHz: 802.11b/g/n/ax
* 4x4 in 5.0GHz: 802.11a/n/ac/ax
* OFDM and OFDMA
* Bidir and MU-MIMO
* Internal antenna 3.1/4.3 dBi (2.4GHz/5GHz)
Power:
* PoE+ 802.3at/af 25.5W
* DC 12V 2.5A
```
```
Note: The OpenWrt image is setup with DHCP and not a static IP.
1. Download the OpenWrt initramfs image. Copy the image to a TFTP server
2. Connect to console on the AP, and connect the LAN port to your LAN
3. Stop auto boot to get to U-boot shell, interrupt the autoboot process by pressing '0' when prompted
4. Set active_fw in env
# setenv active_fw 1
5. Transfer the initramfs image with TFTP
# setenv serverip 192.168.1.10 (IP of TFTP server host)
# setenv ipaddr 192.168.1.1 (IP used by the router for getting the image, must be in the same subnet as the TFTP host)
# tftpboot openwrt-qualcommax-ipq807x-netgear_wax620-initramfs-uImage.itb
6. Reboot and load the image
# bootm
7. SCP factory image to the AP
# scp openwrt-qualcommax-ipq807x-netgear_wax620-squashfs-factory.ubi root@192.168.1.1:/tmp/
8. Connect to device using SSH (use the LAN port)
9. Flash squashfs-factory.ubi from within the initramfs instance of OpenWRT
Before you flash, please check your mtd partitions where mtdX is the right mtd rootfs partition.
# cat /proc/mtd (To check MTD partitions)
# ubiformat /dev/mtd19 -y -f /tmp/openwrt-qualcommax-ipq807x-netgear_wax620-squashfs-factory.ubi
10. Set active_fw to 0
# /usr/sbin/fw_setenv active_fw 0
11. Reboot the AP and your done
# reboot
```
Signed-off-by: Kristian Skramstad <kristian+github@83.no>
vfat support is needed to mount the EFI System Partition (ESP)
during sysupgrade. If it is not available, the sysupgrade process
will not complete
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Add build for the MTK3943 reference board for MT7981B+MT7976C.
**Hardware specification:**
- SoC: MediaTek MT7981B 2x A53
- Flash: various options
- RAM: 256MB DDR3
- Ethernet: 4 x 10/100/1000 Mbps via MT7531AE switch
EITHER 1 x 10/100/1000 Mbps built-in PHY
OR 1 x 10/100/1000/2500 Mbps MaxLinear GPY211C
- Switch: MediaTek MT7531AE
- WiFi: MediaTek MT7976C
- Button: RST, WPS
**Flash instructions for SPIM-NAND:**
- write *mt7981-rfb-spim-nand-preloader.bin to 'BL2' partition
- write *mt7981-rfb-spim-nand-bl31-uboot.fip to 'FIP' partition
- erase 'ubi' partition
- reset board
- create ubootenv and ubootenv2 UBI volumes in U-Boot
- edit environment and set bootcmd, e.g.
setenv bootconf 'config-1#mt7981-rfb-spim-nand#mt7981-rfb-mxl-2p5g-phy-eth1'
setenv bootcmd 'ubi read $loadaddr fit; bootm $loadaddr#$bootconf'
- load initramfs image via TFTP:
setenv serverip 192.168.1.254
setenv ipaddr 192.168.1.1
setenv bootfile openwrt-mediatek-filogic-mediatek_mt7981-rfb-initramfs.itb
saveenv ; saveenv
tftpboot
bootm $loadaddr#$bootconf
- Now use sysupgrade to write OpenWrt firmware to flash.
SNFI-NAND, SPIM-NOR and eMMC all work very similar, a bootable SD card image
is also being generated. However, as the board I've been provided only comes
with SPIM-NAND all other boot media are untested.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
UARTs not used as boot console are currently broken on some MediaTek
targets due to register access depending on the bus clock being enabled.
Add patch to make sure this dependency is always met.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Ethernet LED assignments were incorrectly swapped. Fix the assignment
logic so the correct LED is illuminated for the LAN LEDs.
Signed-off-by: David Bauer <mail@david-bauer.net>
The ZTE MF282 Plus is a LTE router used (exclusively?) by the network
operator "3". It is very similar to the MF286/MF287 but in the form factor
of the MF282.
Specifications
==============
SoC: IPQ4019
RAM: 256MiB
Flash: 8MiB SPI-NOR + 128MiB SPI-NAND
LAN: 1x GBit LAN
LTE: ZTE Cat6
WiFi: 802.11a/b/g/n/ac SoC-integrated
MAC addresses
=============
LAN: from config
WiFi 1: from config + 1
WiFi 2: from config + 2
Installation
============
Option 1 - TFTP
---------------
TFTP installation using UART is preferred. Disassemble the device and
connect serial. Put the initramfs image as openwrt.bin to your TFTP server
and configure a static IP of 192.168.1.100. Load the initramfs image by
typing:
setenv serverip 192.168.1.100
setenv ipaddr 192.168.1.1
tftpboot 0x84000000 openwrt.bin
bootm 0x84000000
From this intiramfs boot you can take a backup of the currently installed
partitions as no vendor firmware is available for download:
ubiattach -m9
cat /dev/ubi0_0 > /tmp/ubi0_0
cat /dev/ubi0_1 > /tmp/ubi0_1
Copy the files /tmp/ubi0_0 and /tmp/ubi0_1 somewhere save.
Once booted, transfer the sysupgrade image and run sysupgrade. You might
have to delete the stock volumes first:
ubirmvol /dev/ubi0 -N ubi_rootfs
ubirmvol /dev/ubi0 -N kernel
Option 2 - From stock firmware
------------------------------
The installation from stock requires an exploit first. The exploit consists
of a backup file that forces the firmware to download telnetd via TFTP from
192.168.0.22 and run it. Once exploited, you can connect via telnet and
login as admin:admin.
The exploit will be available at the device wiki page.
Once inside the stock firmware, you can transfer the -factory.bin file to
/tmp by using "scp" from the stock frmware or "tftp".
ZTE has blocked writing to the NAND. Fortunately, it's easy to allow write
access - you need to read from one file in /proc. Once done, you need to
erase the UBI partition and flash OpenWrt. Before performing the operation,
make sure that mtd9 is the partition labelled "rootfs" by calling
"cat /proc/mtd".
Complete commands:
cd /tmp
tftp -g -r factory.bin 192.168.0.22
cat /proc/driver/sensor_id
flash_erase /dev/mtd9 0 0
dd if=/tmp/factory.bin of=/dev/mtdblock9 bs=131072
Afterwards, reboot your device and you should have a working OpenWrt
installation.
Restore Stock
=============
Option 1 - via UART
-------------------
Boot an OpenWrt initramfs image via TFTP as for the initial installation.
Transfer the two backed-up files to your box to /tmp.
Then, run the following commands - replace $kernel_length and $rootfs_size
by the size of ubi0_0 and ubi0_1 in bytes.
ubiattach -m 9
ubirmvol /dev/ubi0 -N kernel
ubirmvol /dev/ubi0 -N rootfs
ubirmvol /dev/ubi0 -N rootfs_data
ubimkvol /dev/ubi0 -N kernel -s $kernel_length
ubimkvol /dev/ubi0 -N ubi_rootfs -s $rootfs_size
ubiupdatevol /dev/ubi0_0 /tmp/ubi0_0
ubiupdatevol /dev/ubi0_1 /tmp/ubi0_1
Option 2 - from within OpenWrt
------------------------------
This option requires to flash an initramfs version first so that access
to the flash is possible. This can be achieved by sysupgrading to the
recovery.bin version and rebooting. Once rebooted, you are again in a
default OpenWrt installation, but no partition is mounted.
Follow the commands from Option 1 to flash back to stock.
LTE Modem
=========
The LTE modem is similar to the MF286R, it provides an RNDIS interface
and an AT interface.
Other Notes
===========
There is one GPIO Switch "Power button blocker" which, if enabled, does not
trigger a reset of the SoC if the modem reboots. If disabled, the SoC is
rebooted along with the modem. The modem can be rebooted via the exported
GPIO "modem-reset" in /sys/class/gpio.
Signed-off-by: Andreas Böhler <dev@aboehler.at>
New revision of eDPU uses an Marvell MV88E6361 switch to connect the SFP
cage and G.hn IC instead of connecting them directly to the ethernet
controllers.
The same image can be used on both versions as U-Boot will enable the
switch node and disable the unused ethernet controller.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
New revision of Methode eDPU boards uses Marvell 88E6361 switch, so lets
backport it from kernel 6.5.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
New revision of Methode eDPU boards uses Marvell 88E6361 switch, so lets
backport it from kernel 6.5.
Since 5.15 doesnt have phylink_get_caps I had to modify the backport to
use the old mv88e6393x_phylink_validate instead.
I had to fixup one more instance of port_max_speed_mode as well that is not
present in 6.5.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Turn the "gpio-restart" node into a "gpio-export" node for all MF287
variants, similar to the MF287 Pro. Unfortunately, there doesn't seem to be
a "power button blocker" GPIO for the MF287 and MF287 Plus, so a modem
reset always triggers a system reset.
Signed-off-by: Andreas Böhler <dev@aboehler.at>
The ZTE MF287 requires a different board calibration file for ath10k than
the ZTE MF287+. The two devices receive their own DTS, thus the device tree
is slightly refactored.
Signed-off-by: Andreas Böhler <dev@aboehler.at>
For the ZTE MF287 series, a special recovery image is built. The Makefile
worked fine on snapshot, but created corrupt images on the 23.05 images.
By using the appropriate variable, this should be fixed.
Signed-off-by: Andreas Böhler <dev@aboehler.at>
This commit removes the padded zeros in the date formatting.
The padded zeros from the date command causes the numbers
to be interpreted as an octal number by printf. Months, days,
and years with the number 08 or 09 raise an error in printf as an
"invalid octal number" and get interpreted as a zero.
Signed-off-by: Max Qian <public@maxqia.com>
Kernel config for 6.1 on ipq40xx is missing the config for
CONFIG_NVMEM_QCOM_SEC_QFPROM which them makes the build stop with a prompt.
Symbol is there in 5.15 config but 6.1 config was based of a version that
does not yet have it set as it was introduced after the 6.1 PR.
So, disable CONFIG_NVMEM_QCOM_SEC_QFPROM to fix building on 6.1.
Fixes: 825cfa4e36 ("ipq40xx: 6.1: refresh kernel config")
Signed-off-by: Robert Marko <robimarko@gmail.com>
This pulls-in the latest version of qca8k based IPQ4019 driver as well as
the latest version of IPQESS that was sent upstream.
Both qca8k and IPQESS have been improved and cleaned up compared to current
version of patches.
PSGMII PHY mode and missing reset have been upstreamed and will be in
the kernel 6.6.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Adapt and refresh patches to apply.
DSA and ethernet driver patches are dropped as they will be replaced with
the latest version that was sent upstream.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Kernel 6.1 has changed format of sfp_parse_support(), so lets adapt to
those changes so it works on newer kernels as well.
Signed-off-by: Robert Marko <robimarko@gmail.com>
As a preparation to move to 6.1, we need to move the DSA and ethernet
drivers to a 5.15 specific directory as 6.1 will use the latest patchset
that was sent upstream which is too hard to backport to 5.15.
Signed-off-by: Robert Marko <robimarko@gmail.com>
On some WLR-7100 routers, significant packet loss was observed. This is
fixed by configuring a delay on the GMAC0 RXD and RXDV lines.
The values used in this commit are copied from the values used by the
stock firmare (based on register dumping).
Out of four test routers, the problem was consistently observed on two.
It is unclear what the relevant difference is exactly (the two working
routers were v1 001 with AR1022 and v1 002 with AR9342, the two broken
routers were both v1 002 with AR1022). All PCB routing also seems
identical, so maybe there is some stray capacitance on some of these
that adds just enough delay or so...
With this change, the packet loss disappears on the broken routers,
without introducing new packet loss on the previously working routers.
Note that the PHY *also* has delays enabled (through
`qca,ar8327-initvals`) on both RX and TX lines, but apparently that is
not enough, or it is not effective (registers have been verified to be
written).
For detailed discussion of this issue and debug history, see
https://forum.openwrt.org/t/sitecom-wlr-7100-development-progress/79641
Signed-off-by: Matthijs Kooijman <matthijs@stdin.nl>
This patch adds support for the MikroTik RouterBOARD 750 r2, marketed as
hEX lite, a small indoor router with 5x 10/100 Mbps Ethernet ports, one
with PoE in. The device was already supported by the ar71xx target.
Specifications:
- SoC: Qualcomm Atheros QCA9533
- Flash: 16 MB SPI NOR
- RAM: 64 MB
- Ethernet: 4x 10/100 Mbps LAN, 1x 10/100 Mbps WAN (PoE in)
- LEDs: 5x Ethernet port activity (green), 1x user (green)
- Buttons: 1x reset
See https://mikrotik.com/product/RB750r2 for more details.
Not working:
- Serial port (already not working in ar71xx)
Flashing:
TFTP boot initramfs image and then perform sysupgrade. Only the
"Internet" port will ask for an initramfs image. Follow common
MikroTik procedure as in https://openwrt.org/toh/mikrotik/common.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
This adds support for the RBR40 and RBS40 (sold together as RBK40),
two netgear routers identical to SRR60/SRS60 in all but antennae (and
hardware id). See 2cb24b3f3c for details.
Signed-off-by: Thomas Makin <halorocker89@gmail.com>
There's a typo in here: board_name is a function, not a variable. This
issue was pointed out on the OpenWrt forum.
Closes: #13409
Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Mediatek EIP93 Crypto engine is a crypto accelerator which
is available in the Mediatek MT7621 SoC.
Signed-off-by: Aviana Cruz <gwencroft@proton.me>
Co-authored-by: Richard van Schagen <vschagen@icloud.com>
Co-authored-by: Chukun Pan <amadeus@jmu.edu.cn>
When the membase and pci_dev pointer were moved to a new struct in priv,
the actual membase users were left untouched, and they started reading
out arbitrary memory behind the struct instead of registers. This
unfortunately turned the RNG into a constant number generator, depending
on the content of what was at that offset.
To fix this, update geode_rng_data_{read,present}() to also get the
membase via amd_geode_priv, and properly read from the right addresses
again.
Closes#13417.
Reported-by: Timur I. Davletshin <timur.davletshin@gmail.com>
Tested-by: Timur I. Davletshin <timur.davletshin@gmail.com>
Suggested-by: Jo-Philipp Wich <jo@mein.io>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Fix PSE port assignment for 3rd GMAC on MT7988 and make sure dma_addr
is always initialized to prevent potentially accessing uninitialized
stack memory in the error path.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
ALFA Network AX1800RM (FCC ID: 2AB877621) is a dual-band Wi-Fi 6
(AX1800) router, based on MediaTek MT7621A + MT79x5D platform.
Specifications:
- SOC: MT7621A (880 MHz)
- DRAM: DDR3 256 MiB (Nanya NT5CC128M16JR-EK)
- Flash: 16 MiB SPI NOR (EN25QH128A-104HIP)
- Ethernet: 4x 10/100/1000 Mbps (SOC's built-in switch)
- Wi-Fi: 2x2:2 2.4/5 GHz (MT7905DAN + MT7975DN)
(MT7905DAN doesn't support background DFS scan/BT)
- LED: 6x green, 1x green/red
- Buttons: 2x (reset, WPS)
- Antenna: 4x external, non-detachable omnidirectional
- UART: 1x 4-pin (2.54 mm pitch, J4, not populated)
- Power: 12 V DC/1 A (DC jack)
MAC addresses:
LAN: 00:c0:ca:xx:xx:4e (factory 0x4, +2)
WAN: 00:c0:ca:xx:xx:4f (factory 0x4, +3)
2.4 GHz: 00:c0:ca:xx:xx:4c (factory 0x4, device's label)
5 GHz: 00:c0:ca:xx:xx:4c (factory 0xa)
Flash instructions for web-based U-Boot recovery:
1. Power the device with WPS button pressed and wait around 10 seconds.
2. Setup static IP 192.168.1.2/24 on your PC.
3. Go to 192.168.1.1 in browser and upload 'recovery' image.
The device runs LEDE 17.01 (kernel 4.4.x) based firmware with 'failsafe'
mode available which allows alternative upgrade method:
1. Run device in 'failsafe' mode and change password for default user.
2. SSH to the device, transfer 'sysupgrade' image and perform upgrade
in forced mode, without preserving settings: 'sysupgrade -n -F ...'.
Other notes:
If you own early version of this device, the vendor firmware might
refuse OpenWrt image because of missing custom header. In that case,
ask vendor's customer support for stock firmware without custom header
support/requirement.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Since kernel 5.13 this is needed to enable USB ports on all devices in
subtarget. Previously TF-A and COMPHY driver might have set up this PHY,
but not anymore.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Tested-by: Robert Marko <robimarko@gmail.com>
This should be a part of kernel major bump. Fortunately it didn't stall
compilation, so no fixes tag.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
**Hardware specification:**
- SoC: MediaTek MT7981B 2x A53
- Flash: ESMT F50L1G41LB 128MB
- RAM: Nanya NT5CC128M16JR-EK 256MB
- Ethernet: 4 x 10/100/1000 Mbps
- Switch: MediaTek MT7531AE
- WiFi: MediaTek MT7976C
- Button: Reset, Mesh
- Power: DC 12V 1A
- UART: 3.3v, 115200n8
| Layout: |
| :-------- |
| <Antenna> |
| VCC |
| GND |
| Tx |
| Rx |
**Flash instructions:**
1. Rename `openwrt-mediatek-filogic-cetron_ct3003-squashfs-factory.bin` to `factory.bin`.
2. Upload the `factory.bin` using the device's Web interface.
3. Click the upgrade button and wait for the process to finish.
4. Access the OpenWrt interface using the same password.
5. Use the 'Restore' function to reset the firmware to its initial state.
**Notes:**
If you plan to recovery the stock firmware in the future, it's advisable
to connect the device via the serial port and enter failsafe mode to
back up all the MTD partitions before proceeding the steps above.
Signed-off-by: Patricia Lee <patricialee320@gmail.com>
Make use of minor sector size (4k) erasure on supported flash chips
to improve spi read/write performance.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
ath79 PCIe interrupt controller has stopped working correctly. This
is because the DT exposing a non-sensical interrupt-map property,
and their drivers relying on the kernel ignoring this property[1].
This patch fixes the PCIe init error:
ath9k 0000:00:00.0: of_irq_parse_pci: failed with rc=-14
Notice:
This is just a workaround, not a fix. PCIe driver and related dts
node need to be rewritten.
[1] https://lore.kernel.org/all/20211201114102.13446-1-maz@kernel.org/
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
All kernel configs are refreshed by
'make kernel_oldconfig CONFIG_TARGET=target' and
'make kernel_oldconfig CONFIG_TARGET=subtarget'.
upstreamed patches:
010-v5.17-spi-ar934x-fix-transfer-and-word-delays.patch
011-v5.17-spi-ar934x-fix-transfer-size.patch
020-v5.18-spi-ath79-Implement-the-spi_mem-interface.patch
030-v5.18-ath79-add-support-for-booting-QCN550x.patch
build and run tested on:
ath79/generic/ar7241
ath79/generic/qca9563
ath79/nand/ar9344
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Some symbols are outdated or missing due to daily kernel bumps. It's
better to re-add them. All configs are automatically refreshed by
'make kernel_oldconfig CONFIG_TARGET=taget' and
'make kernel_oldconfig CONFIG_TARGET=subtarget'
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
This reverts commit 5356462ce5.
Kernel switching to fw_devlink=on as default broke probing some devices.
Revert it until we get a proper fix.
It seemed that mtd OF_POPULATED hack resolved probing issues but
apparently not all of them. We got reports about reading MAC using NVMEM
not working and USB controllers not working.
Ref: #10232Fixes: #13412
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Fix the issue of dts buswidth cannot be applied properly with spi driver.
Fix the name of buswidth to bus-width in dts in order to fit the format
in linux spi kernel[1] so that spi-tx-bus-width & spi-rx-bus-width can be
parsed properly.
[1] Documentation/devicetree/bindings/spi/spi-controller.yaml
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
This adds support for Radxa ROCK Pi E, rockchip rk3328 board.
Specification:
- CPU: Rockchip RK3328 64-bit Quad-core
- RAM: DDR3 256MB ~ 2GB
- Network:
1 x 10/100/1000M Ethernet
1 x 10/100M Ethernet
- Storage:
1 x MicroSD Slot
1 x eMMC Module Slot
- USB Host/OTG:
1 x USB3.0 Type A HOST
1 x USB2.0 HOST (40-pin pin-header)
- Wireless
RTL8723DU/RTL8821CU
- Debug Serial:
1500000 baud at UART2 ( 40-pin pin-header)
- Power Supply:
Type-C 5V
Optionally PoE
Installation:
- Write image to SD Card or EMMC with dd
- Boot ROCK Pi E from the SD Card
Signed-off-by: Jayantajit Gogoi <jayanta.gogoi525@gmail.com>
The bootcmd limits the kernel to 4 MiB which is
exceeded when using Device/FitImage. Device/FitzImage
reduces the size to around 3 MiB.
Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Thomas Bong <thomas.bong@devolo.de>
Renamed the interfaces to match the other devices.
Name the interface connected to the builtin G.hn chip 'ghn'.
This might toggle at runtime while the G.hn chip is in the
bootloader.
Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Thomas Bong <thomas.bong@devolo.de>
The NMBM-Enabled layout did not use fit image,
it just need default process. So it was been removed in platform.sh.
It will fix sysupgrade error for xiaomi,mi-router-wr30u-112m-nmbm.
Signed-off-by: Hank Moretti <mchank9999@gmail.com>
Relocating the device tree is required for being apply to apply
device tree overylay at boot.
Fixes: 34bb33094a ("mediatek: use updated device tree overlay mechanism for BPi-R64")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This symbol was added by commit 2e6f34faa7e0 ("Input: Add IBM Operation
Panel driver") to v6.1. It depends on I2C so it's available to limited
amount of targets. It needs to be specified thought to allow kernel
configuration.
For bcm53xx this fixes:
IBM Operation Panel driver (INPUT_IBM_PANEL) [N/m/?] (NEW)
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
These suboptions (PLATFORM, FSL_MC and MLX5_VFIO_PCI)
may be prompted for when VFIO is enabled, regardless of
architecture.
These are not related to the main vfio use case
(passthrough of PCIe devices)
Signed-off-by: Mathew McBride <matt@traverse.com.au>
When adapting the network configuration for MT7988 RFB a stray quote
was left in a script. Remove it to fix generating the default network
configuration.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Import commits from upstream Linux replacing some downstream patches.
Move accepted patches from pending-{5.15,6.1} to backport-{5.15,6.1}.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Some recent models of the Ubiquiti Networks UniFi 6 LR access point
come with a RealTek RTL8211FS 1000M/100M/10M PHY instead of the
Aquantia AQR112 2500M/1000M/100M/10M PHY used in both v1 and v2. Add
build for this variant so we can support Ethernet with the PHY.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Switch to OpenWrt uImage.FIT bootmethod and include various bootloader
artifacts with the generated binaries.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Set correct pull-type data and add additional uart groups for MT7981.
Assign functions to configure pin bias for MT7986.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Using the I2C host controller on the MT7981 SoC requires 4 clocks to
be enabled. One of them, the pmic clk, is only enabled in case
'mediatek,have-pmic' is also set which has other consequences which
are not desired in this case.
Allow defining a pmic clk even in case the 'mediatek,have-pmic' propterty
is not present and the bus is not used to connect to a pmic, but may
still require to enable the pmic clock.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The patch was wrongly tagged as being part of Linux 6.0 even though it
was only committed with Linux 6.2 and hence needs to be backported for
Linux 6.1.
Fixes: fa79baf4a6 ("generic: copy backport, hack, pending patch and config from 5.15 to 6.1")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Unfortunately some device tree properties have slipped under the table
when switching from our downstream device tree.
Bring back 3W power for SFP cages and restore thermal trip points to
make sense again.
Fixes: 7a0ec001ff ("mediatek: sync MT7986 device trees with upstream")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The DIR-890L is very similar to DIR-885L, but has both USB2
and USB3. The signature for the wrgac36 board was copied from
DD-Wrt.
The DIR-890L bootstrap will only load the first 2 MB after
the SEAMA header in the NAND flash, uncompress it with LZMA
and execute it. Since the compressed kernel will not fit in
2 MB we have a problem. Solve this by putting a LZMA
compressed U-Boot into the first 128 KB of the flash
followed by the kernel. The bootstrap will then uncompress
and execute U-Boot and then we let U-Boot read the kernel
from flash and execute it.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
One of our SPI devices references this node, but we never enabled it.
This clutters up probe deferral logs.
(NB: this SPI device still doesn't have a real driver, so it's just here
for documentation and/or tinkering.)
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The qcom spm driver is currently broken for IPQ8064 OnHub devices on
kernel 6.1, such that it hangs the system when booting, much to the
consternation of users. This is especially bad as these devices don't
yet have a fully-supported release branch, and are still sometimes
landing on snapshot builds.
OnHub devices have their own kernel config, so it's not that wide of an
impact to disable this.
I haven't fully gotten to the bottom of this, but:
(a) The vendor kernel didn't have any SPM driver at all, and didn't
utilize cpuidle.
(b) The device tree has never included any (non-disabled) cpuidle
states, so even when this driver was present on 5.15 (last
known-working kernel), it didn't actually do anything -- it bailed
early, before ever doing any SPM initialization.
(c) Refactoring in Linux 5.16 [1] caused the SPM driver to be activated
unconditionally, including setting us into standby mode
(PM_SLEEP_MODE_STBY) by default.
Removing the one PM_SLEEP_MODE_STBY line from drivers/soc/qcom/spm.c
seems to fix the problem, but that isn't much different than simply
disabling the driver, so I go with that for now.
I also disable CONFIG_ARM_QCOM_SPM_CPUIDLE, becuase it 'select's
QCOM_SPM.
NB: it's possible there's some other deeper root cause involved in here.
For one, I notice that CPU hotplug (e.g., echo 0 >
/sys/devices/system/cpu/cpu1/online, echo 1 > ...) doesn't work right
either. Perhaps there's some mismatch on upstream Linux qcom-scm
behavior and the old boot firmware used for these systems? It wouldn't
be the first time, as we've had some similar incompatibilities on the
next generation of these devices, Google WiFi [2].
[1] Commit 60f3692b5f0b ("cpuidle: qcom_spm: Detach state machine from
main SPM handling")
[2] [RFC] qcom_scm: IPQ4019 firmware does not support atomic API?
https://lore.kernel.org/linux-arm-kernel/20200913201608.GA3162100@bDebian/
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
