The pwmchip_remove() function returns void now. Fix a compile problem in
the drivers/pwm/pwm-mediatek-ramips.c driver.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
In the build of the ramips/mt76x8 target the user gets asked about these
two configuration options, add them to the generic kernel configuration.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The CONFIG_DRM_XEN_FRONTEND configuration symbol is also used by the
layerscape target, move it to the generic kernel configuration.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This reverts commit 97c77fff28 as commit
8be6350f66 ("generic: 5.15: allow MV88E6xxx built-in when PTP support
disabled") contains the fix, so lets enable kernel 5.15 on mvebu again.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
A device COMPILE target should not depend on another COMPILE.
Otherwise race condition may happen.
The loader is very small. Compiling it twice shouldn't
have a huge impact.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
As described in commit 97c77fff28
MV88E6xxx driver (NET_DSA_MV88E6XXX) cannot be built-in when PTP
(PTP_1588_CLOCK) is a module in Linux 5.15. But actually it should be
allowed to be built-in when its PTP support (NET_DSA_MV88E6XXX_PTP) is
disabled.
This adds a patch to fix that.
Signed-off-by: Johnny S. Lee <foss@jsl.io>
General specification:
- SoC Type: MediaTek MT7620N (580MHz)
- ROM: 8 MB SPI-NOR (W25Q64FV)
- RAM: 64 MB DDR (M13S5121632A)
- Switch: MediaTek MT7530
- Ethernet: 5 ports - 5×100MbE (WAN, LAN1-4)
- Wireless 2.4 GHz: b/g/n
- Buttons: 1 button (RESET)
- Bootloader: U-Boot 1.1.3, MediaTek U-Boot: 5.0.0.5
- Power: 12 VDC, 1.0 A
Flash by the native uploader in 2 stages:
1. Use the native uploader to flash an initramfs image. Choose
openwrt-ramips-mt7620-snr_cpe-w4n-mt-initramfs-kernel.bin file by
"Administration/Management/Firmware update/Choose File" in vendor's
web interface (ip: 192.168.1.10, login: Admin, password: Admin).
Wait ~160 seconds.
2. Flash a sysupgrade image via the initramfs image. Choose
openwrt-ramips-mt7620-snr_cpe-w4n-mt-squashfs-sysupgrade.bin
file by "System/Backup/Flash Firmware/Flash image..." in
LuCI web interface (ip: 192.168.1.1, login: root, no password).
Wait ~240 seconds.
Flash by U-Boot TFTP method:
1. Configure your PC with IP 192.168.1.131
2. Set up TFTP server and put the
openwrt-ramips-mt7620-snr_cpe-w4n-mt-squashfs-sysupgrade.bin
image on your PC
3. Connect serial port (57600 8N1) and turn on the router.
Then interrupt "U-Boot Boot Menu" by hitting 2 key (select "2:
Load system code then write to Flash via TFTP.").
Press Y key when show "Warning!! Erase Linux in Flash then burn
new one. Are you sure? (Y/N)"
Input device IP (192.168.1.1) ==:192.168.1.1
Input server IP (192.168.1.131) ==:192.168.1.131
Input Linux Kernel filename () ==:
openwrt-ramips-mt7620-snr_cpe-w4n-mt-squashfs-sysupgrade.bin
3. Wait ~120 seconds to complete flashing
Signed-off-by: Alexey Bartenev <41exey@proton.me>
KuWFi C910 is an 802.11n (300N) indoor router with LTE support.
I can't find anywhere the OEM firmware. So if you want to restore the
original firmware you must do a dump before the OpenWrt flash.
According to the U-Boot, the board name is Iyunlink MINI_V2.
Hardware
--------
SoC: Qualcomm QCA9533 650/400/200/25/25 MHz (CPU/RAM/AHB/SPI/REF)
RAM: 128 MB DDR2 16-bit CL3-4-4-10 (Nanya NT5TU64M16HG-AC)
FLASH: 16 MB Winbond W25Q128
ETH:
- 2x 100M LAN (QCA9533 internal AR8229 switch, eth0)
- 1x 100M WAN (QCA9533 internal PHY, eth1)
WIFI:
- 2.4GHz: 1x QCA9533 2T2R (b/g/n)
- 2 external non detachable antennas (near the power barrel side)
LTE:
- Quectel EC200T-EU (or -CN or -AU depending on markets)
- 2 external non detachable antennas (near the sim slot side)
BTN:
- 1x Reset button
LEDS:
- 5x White leds (Power, Wifi, Wan, Lan1, Lan2)
- 1x RGB led (Internet)
UART: 115200-8-N-1 (Starting from lan ports in order: GND, RX, TX, VCC)
Everything works correctly.
MAC Addresses
-------------
LAN XX:XX:XX:XX:XX:48 (art@0x1002)
WAN XX:XX:XX:XX:XX:49 (art@0x1002 + 1)
WIFI XX:XX:XX:XX:XX:48
LABEL XX:XX:XX:XX:XX:48
Installation
------------
Turn the router on while pressing the reset button for 4 seconds.
You can simply count the flashes of the first lan led. (See notes)
If done correctly you should see the first lan led glowing slowly and
you should be able to enter the U-Boot web interface.
Click on the second tab ("固件") and select the -factory.bin firmware
then click "Update firmware".
A screen "Update in progress" should appear.
After few minutes the flash should be completed.
This procedure can be used also to recover the router in case of soft
brick.
Backup the original firmware
----------------------------
The following steps are intended for a linux pc. However using the
right software this guide should also work for Windows and MacOS.
1) Install a tftp server on your pc. For example tftpd-hpa.
2) Create two empty files in your tftp folder called:
kuwfi_c910_all_nor.bin
kuwfi_c910_firmware_only.bin
3) Give global write permissions to these files:
chmod 666 kuwfi_c910_all_nor.bin
chmod 666 kuwfi_c910_firmware_only.bin
4) Start a netcat session on your pc with this command:
nc -u -p 6666 192.168.1.1 6666
5) Set the static address on your pc: 192.168.1.2. Connect the router
to your pc.
6) Turn the router on while pressing the reset button for 8-9 seconds.
You can simply count the flashes of the first lan led. If you
press the reset button for too many seconds it will continue
the normal boot, so you have to restart the router. (See notes)
7) If done correctly you should see the U-Boot network console and you
should see the following lines on the netcat session:
Version and build date:
U-Boot 1.1.4-55f1bca8-dirty, 2020-05-07
Modification by:
Piotr Dymacz <piotr@dymacz.pl>
https://github.com/pepe2k/u-boot_mod
u-boot>
8) Start the transfer of the whole NOR:
tftpput 0x9f000000 0x1000000 kuwfi_c910_all_nor.bin
9) The router should start the transfer and it should end with a
message like this (pay attention to the bytes transferred):
TFTP transfer complete!
Bytes transferred: 16777216 (0x1000000)
10) Repeat the same transfer for the firmware:
tftpput 0x9f050000 0xfa0000 kuwfi_c910_firmware_only.bin
11) The router should start the transfer and it should end with a
message like this (pay attention to the bytes transferred):
TFTP transfer complete!
Bytes transferred: 16384000 (0xfa0000)
12) Now you have the backup for the whole nor and for the firmware
partition. If you want to restore the OEM firmware from OpenWrt
you have to flash the kuwfi_c910_firmware_only.bin from the
U-Boot web interface.
WARNING: Don't use the kuwfi_c910_all_nor.bin file. This file
is only useful if you manage to hard brick the router or you
damage the art partition (ask on the forum)
Notes
-----
This router (or at least my unit) has the pepe2k's U-Boot. It's a
modded U-Boot version with a lot of cool features. You can read more
here: https://github.com/pepe2k/u-boot_mod
With this version of U-Boot, pushing the reset button while turning on
the router starts different tools:
- 3-5 seconds: U-Boot web interface that can be used to replace the
firmware, the art or the U-Boot itself
- 5-7 seconds: U-Boot uart console
- 7-10 seconds: U-Boot network console
- 11+ seconds: Normal boot
The LTE modem can be used in cdc_ether (ECM) or RNDIS mode.
The default mode is ECM and in this commit only the ECM software is
included. In order to set RNDIS mode you must use this AT command:
AT+QCFG="usbnet",3
In order to use again the ECM mode you must use this AT command:
AT+QCFG="usbnet",1
Look for "Quectel_EC200T_Linux_USB_Driver_User_Guide_V1.0.pdf" for
other AT commands
Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
1. Use ARTIFACTS to build factory image. This change allows users to
generate initramfs factory image using OpenWrt ImageBuilder.
2. Override the default bootargs property defined in "mt7621.dtsi".
Although we use the "bootargs-override" property to set bootargs,
the default "bootargs" property will still be written into the
device tree, so it is better to override it.
Tested on SIM SIMAX1800T
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
1. Explicitly declare gpio pin groups to ensure that gpio works properly.
2. Override bootargs in device tree to avoid modifying u-boot envs during
initial installation.
Tested on H3C TX1801 Plus
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
The compatible in the device tree is "haoyu,a10-marsboard",
modify the board_name to keep it consistent.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
The kmod prefix for sound-soc-sunxi is missing, fix it.
Also add kmod-sound-core as dependence.
Fixes: 6a35659 ("sunxi: Added profile for HAOYU Electronics Marsboard A10")
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Pull the calibration data from the nvmem subsystem. This allows us to
move userspace caldata extraction into the device-tree definition.
While working on it remove stale uboot partition label and merge art
into partition node.
Signed-off-by: Nick Hainke <vincent@systemli.org>
Pull the calibration data from the nvmem subsystem. This allows us to
move userspace caldata extraction into the device-tree definition.
Merge art into partition node.
Signed-off-by: Nick Hainke <vincent@systemli.org>
Pull the calibration data from the nvmem subsystem. This allows us to
move userspace caldata extraction into the device-tree definition.
Merge art into partition node.
Signed-off-by: Nick Hainke <vincent@systemli.org>
Pull the calibration data from the nvmem subsystem. This allows us to
move userspace caldata extraction into the device-tree definition.
Merge art into partition node.
Signed-off-by: Nick Hainke <vincent@systemli.org>
Pull the calibration data from the nvmem subsystem. This allows us to
move userspace caldata extraction into the device-tree definition.
Merge art into partition node.
Signed-off-by: Nick Hainke <vincent@systemli.org>
'cs-gpios = <0>, <0>' is a hack in ath79 to override the incorrectly
specified maximum number of chipselects available in spi-ath79.c.
It's not needed here and must have been copied here by mistake.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
In this implementation, the flash partition layout is adjusted to avoid
modifying the uboot environment of mtdparts. This ensures that the 30M
ubi_kernel partition remains aligned with the stock ubi partition, and
the kernel volume is placed in it. This allows the stock uboot to boot
from it without changing the mtdparts, which is useful for reverting back
to the stock firmware using Xiaomi Firmware Tools. In actual testing,
modifying mtdparts has been found to break Xiaomi Firmware Tools.
1. use ARTIFACTS to generate initramfs-factory.ubi for easy installation.
2. The NAND flash layout is changed to allow for reverting back to the
stock firmware.
3. Before performing sysupgrade, do some cleanup in platform_pre_upgrade
to ensure a clean installation of OpenWRT.
4. Setup the uboot env to ensure that the system always boot, which can
be helpful for users who may forget to do this before sysupgrade in
the initramfs.
New flash instructions:
1. Gain ssh access. Please refer to:
https://openwrt.org/toh/xiaomi/redmi_ax6000#installation)
2. Check which system current u-boot is loading from:
COMMAND: `cat /proc/cmdline`
sample OUTPUT: `console=ttyS0,115200n1 loglevel=8 firmware=1 uart_en=1`
if firmware=1, current system is ubi1
if firmware=0, current system is ubi0
3. Setup nvram and write the firmware:
If the current system is ubi1, please set it up so that the next time
it will boot from ubi, and write the firmware to ubi:
```
nvram set boot_wait=on
nvram set uart_en=1
nvram set flag_boot_rootfs=0
nvram set flag_last_success=0
nvram set flag_boot_success=1
nvram set flag_try_sys1_failed=0
nvram set flag_try_sys2_failed=0
nvram commit
ubiformat /dev/mtd8 -y -f /tmp/initramfs-factory.ubi
```
If the current system is ubi, please set it up so that the next time
it will boot from ubi1, and write the firmware to ubi1:
```
nvram set boot_wait=on
nvram set uart_en=1
nvram set flag_boot_rootfs=1
nvram set flag_last_success=1
nvram set flag_boot_success=1
nvram set flag_try_sys1_failed=0
nvram set flag_try_sys2_failed=0
nvram commit
ubiformat /dev/mtd9 -y -f /tmp/initramfs-factory.ubi
```
4. After rebooting, the system should now boot into the openwrt initramfs.
Flash the squashfs-sysupgrade.bin via using ssh or luci.
```
sysupgrade -n /tmp/squashfs-sysupgrade.bin
```
Done.
For existing users of the Redmi AX6000 running OpenWrt, here are the steps to
switch to this new layout:
1. Flash initramfs-factory.ubi
```
mtd -r -e ubi write /tmp/initramfs-factory.ubi ubi
```
2. After rebooting, the system will boot into the new openwrt-initramfs.
Log in and perform a sysupgrade to complete the process.
```
sysupgrade -n /tmp/squashfs-sysupgrade.bin
```
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Add support for EON EN25QX128A spi nor flash with no flags as it does
support SFDP parsing.
Fixes: #9442
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Tested-by: Szabolcs Hubai <szab.hu@gmail.com> [ramips/mt7621: xiaomi_mi-router-4a-gigabit]
add DT nodes and default package for the LEDs on Redmi AX6000
Signed-off-by: Furong Xu <xfr@outlook.com>
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Without explicitly enabling sel_clk, clk_disable_unused() will disable
it when boot is done, causing CPU hang on SPI1 register access on MT7986.
Explicitly enable sel_clk to make SPI1 functional.
Signed-off-by: Furong Xu <xfr@outlook.com>
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
- rtl83xx_vlan_filtering()
"struct switchdev_trans *trans" parameter was removed[1] and
"struct netlink_ext_ack *extack" was added[2].
[1]: https://www.spinics.net/lists/netdev/msg712250.html
[2]: https://www.spinics.net/lists/netdev/msg722496.html
- rtl83xx_vlan_add/del()
vlan->vid_begin and vlan->vid_end were removed and vlan->vid was
added[3].
[3]: https://www.spinics.net/lists/netdev/msg712248.html
- rtl83xx_vlan_prepare()
"port_vlan_prepare" member was removed from "dsa_switch_ops" struct
in dsa.h[4] and vlan_prepare function should be called from vlan_add
function. Also, change return type of vlan_add function to int.
[4]: https://www.spinics.net/lists/netdev/msg712252.html
- rtl83xx_port_mdb_add()
"port_mdb_prepare" member in "dsa_switch_ops" struct was removed and
preparation need to be done in the function of "port_mdb_add" member
instead. And also, int type need to be returned on "port_mdb_add"
member[5].
[5]: https://www.spinics.net/lists/netdev/msg712251.html
- rtl83xx_port_pre_bridge_flags(), rtl83xx_port_bridge_flags()
The current "port_pre_bridge_flags" member and "port_bridge_flags"
member in "dsa_switch_ops" in dsa.h has flags of
"struct switchdev_brport_flags" type instead[6], so adjust to it.
And, the changed features are passed by flags.mask[7] in
rtl83xx_port_bridge_flags(), so check it before calling function
to enable/disable fieature.
[6]: https://lore.kernel.org/lkml/20210212151600.3357121-7-olteanv@gmail.com/
[7]: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=e18f4c18ab5b0dd47caaf8377c2e36d66f632a8c
Suggested-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
[shorten final return statement of rtl83xx_port_mdb_add()]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
- 007-5.16-gpio-realtek...: upstreamed on 5.16 and backported to 5.15.3
- 708-brflood-spi.patch : upstreamed
- 709-lag-offloading.patch: upstreamed
- 713-v5.12-net-dsa-... : upstreamed and some implementations are
replaced
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
The following drivers were upstreamed and available on 5.15, so drop
from OpenWrt tree.
- realtek-otto-gpio (5.13)
- realtek-rtl-spi (5.12)
- realtek-rtl-intc (5.12)
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
|109.3-19: Warning (reg_format): macaddr@0:reg:property has invalid length (8 bytes)
|113.3-24: Warning (reg_format): calibration@1000:reg: property has invalid length (8 bytes)
|117.3-24: Warning (reg_format): calibration@5000:reg: property has invalid length (8 bytes)
also integrate the art-nodes nodes back into the partition-subnode
and change the calibration labels to match what everyone else is
doing.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
|109.3-19: Warning (reg_format): macaddr@0:reg:property has invalid length (8 bytes)
|113.3-24: Warning (reg_format): calibration@1000:reg: property has invalid length (8 bytes)
|117.3-24: Warning (reg_format): calibration@5000:reg: property has invalid length (8 bytes)
also integrate the art-nodes nodes back into the partition-subnode
and change the calibration labels to match what everyone else is
doing.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Pull the calibration data from the nvmem subsystem. This allows us to
move userspace caldata extraction into the device-tree definition.
Signed-off-by: Nick Hainke <vincent@systemli.org>
(removed mtd-cal-data property, merged art + addr nodes back into
partition)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Pull the calibration data from the nvmem subsystem. This allows us to
move userspace caldata extraction into the device-tree definition.
Signed-off-by: Nick Hainke <vincent@systemli.org>
(merged art node back into partition-node)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Pull the calibration data from the nvmem subsystem. This allows us to
move userspace caldata extraction into the device-tree definition.
Signed-off-by: Nick Hainke <vincent@systemli.org>
(merged art into partition node, removed stale uboot label)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Remove the caldata extraction in userspace. The board already uses
nvmem-cells since
commit e354b01baf ("ath79: calibrate all ar9344 tl-WDRxxxx with nvmem")
Signed-off-by: Nick Hainke <vincent@systemli.org>
Pull the calibration data from the nvmem subsystem. This allows us to
move userspace caldata extraction into the device-tree definition.
Signed-off-by: Nick Hainke <vincent@systemli.org>
Pull the calibration data from the nvmem subsystem. This allows us to
move userspace caldata extraction into the device-tree definition.
Signed-off-by: Nick Hainke <vincent@systemli.org>
(merged art-node back into partition-node)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Pull the calibration data from the nvmem subsystem. This allows us to
move userspace caldata extraction into the device-tree definition.
Signed-off-by: Nick Hainke <vincent@systemli.org>
Some carrier boards [1][2] for the Raspberry Pi CM4 that are specifically
designed to be used as routers come with secondary NICs using a Realtek
RTL8111 Gigabit Ethernet chip.
When using such a board as a router with OpenWrt, it is very helpful
when both NICs are working by default. Since the Raspberry Pi 4 and the
CM4 have plenty of disk space, it should cause no harm to include the
kmod-r8169.
[1] https://wiki.dfrobot.com/Compute_Module_4_IoT_Router_Board_Mini_SKU_DFR0767
[2] https://www.waveshare.com/wiki/CM4-DUAL-ETH-MINI
Signed-off-by: Johannes Heimansberg <git@jhe.dedyn.io>
(r8169 should pull in the necessary dependencies.)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
A backported patch to the BCMA driver necessary to support the
DWL-8610AP and DIR-890L. Patch will be in upstream v6.2.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Kernel 5.10.158 added a prompt for the FUNCTION_ERROR_INJECTION symbol.
This is exposed in builds with CONFIG_KERNEL_KPROBES enabled, causing
those builds to fail due to a missing symbol. Add the symbol to fix
this.
Fixes: 6801c460b6 ("kernel: bump 5.10 to 5.10.158")
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Kernel 5.15.82 added a prompt for the FUNCTION_ERROR_INJECTION symbol.
This is exposed in builds with CONFIG_KERNEL_KPROBES enabled, causing
those builds to fail due to a missing symbol. Add the symbol to fix
this.
Fixes: 68426e54ed ("kernel: bump 5.15 to 5.15.82")
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
The testing kernel has been running fine for months on a rather complex
network setup, with one exception being a crash in
__xfrm_state_delete(). This crash has been fixed in kernel 5.15.82, so
let's switch the qoriq target to kernel 5.15 by default.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Compex WPQ864 contains a non standard partition table. Each partition
node should be named partition and should contain a valid reg.
Fix an extra "-" present after the reg for SBL2_1 partition.
Also add "0:" to each qcom default partition following smem naming.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The refreshed patch actually use the format of <start size start size>
instead of <start end start end>. This cause boot fail since the rootfs
can't be mounted with these wrong values.
Fix it to the correct format in each affected dts.
Fixes: #11498
Fixes: 6134ba4a34 ("ipq806x: 5.15: add boot-partitions binding to fix block warning")
Tested-by: Matt Buczko <mbuczko@hotmail.com> # Askey RT4230W
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
TP-Link CPE605-v1 is an outdoor wireless CPE for 5 GHz with
one Ethernet port based on Atheros AR9344
Specifications:
- 560/450/225 MHz (CPU/DDR/AHB)
- 1x 10/100 Mbps Ethernet
- 64 MB of DDR2 RAM
- 8 MB of SPI-NOR Flash
- 23dBi high-gain directional antenna and a dedicated metal reflector
- Power, LAN, WLAN5G green LEDs
- 3x green RSSI LEDs
Flashing instructions:
Flash factory image through stock firmware WEB UI or through TFTP
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254
Signed-off-by: Andrew Cameron <apcameron@softhome.net>
Etisalat S3 is a wireless WiFi 5 router manufactured by Sercomm company.
Device specification
--------------------
SoC Type: MediaTek MT7621AT
RAM: 256 MiB
Flash: 128 MiB
Wireless 2.4 GHz (MT7603EN): b/g/n, 2x2
Wireless 5 GHz (MT7615E): a/n/ac, 4x4
Ethernet: 5x GbE (WAN, LAN1, LAN2, LAN3, LAN4)
USB ports: 1x USB3.0
Button: 2 buttons (Reset & WPS)
LEDs:
- 1x Status (RGB)
- 1x 2.4G (blue, hardware, mt76-phy0)
- 1x 5G (blue, hardware, mt76-phy1)
Power: 12 VDC, 1.5 A
Connector type: barrel
Bootloader: U-Boot
Installation
-----------------
1. Login to the router web interface under admin account
2. Navigate to Settings -> Configuration -> Save to Computer
3. Decode the configuration. For example, using cfgtool.py tool (see
related section):
cfgtool.py -u configurationBackup.cfg
4. Open configurationBackup.xml and find the following line:
<PARAMETER name="Password" type="string" value="<your router serial \
is here>" writable="1" encryption="1" password="1"/>
5. Insert the following line after and save:
<PARAMETER name="Enable" type="boolean" value="1" writable="1" encryption="0"/>
6. Encode the configuration. For example, using cfgtool.py tool:
cfgtool.py -p configurationBackup.xml
7. Upload the changed configuration (configurationBackup_changed.cfg) to
the router
8. Login to the router web interface (SuperUser:ETxxxxxxxxxx, where
ETxxxxxxxxxx is the serial number from the backplate label)
9. Navigate to Settings -> WAN -> Add static IP interface (e.g.
10.0.0.1/255.255.255.0)
10. Navigate to Settings -> Remote cotrol -> Add SSH, port 22,
10.0.0.0/255.255.255.0 and interface created before
11. Change IP of your client to 10.0.0.2/255.255.255.0 and connect the
ethernet cable to the WAN port of the router
12. Connect to the router using SSH shell under SuperUser account
13. Run in SSH shell:
sh
14. Make a mtd backup (optional, see related section)
15. Change bootflag to Sercomm1 and reboot:
printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3
reboot
16. Login to the router web interface under admin account
17. Remove dots from the OpenWrt factory image filename
18. Update firmware via web using OpenWrt factory image
Revert to stock
---------------
Change bootflag to Sercomm1 in OpenWrt CLI and then reboot:
printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3
mtd backup
----------
1. Set up a tftp server (e.g. tftpd64 for windows)
2. Connect to a router using SSH shell and run the following commands:
cd /tmp
for i in 0 1 2 3 4 5 6 7 8 9 10; do nanddump -f mtd$i /dev/mtd$i; \
tftp -l mtd$i -p 10.0.0.2; md5sum mtd$i >> mtd.md5; rm mtd$i; done
tftp -l mtd.md5 -p 10.0.0.2
Recovery
--------
Use sercomm-recovery tool.
Link: https://github.com/danitool/sercomm-recovery
MAC Addresses
-------------
+-----+------------+---------+
| use | address | example |
+-----+------------+---------+
| LAN | label | *:50 |
| WAN | label + 11 | *:5b |
| 2g | label + 2 | *:52 |
| 5g | label + 3 | *:53 |
+-----+------------+---------+
The label MAC address was found in Factory 0x21000
cfgtool.py
----------
A tool for decoding and encoding Sercomm configs.
Link: https://github.com/r3d5ky/sercomm_cfg_unpacker
Co-authored-by: Karim Dehouche <karimdplay@gmail.com>
Co-authored-by: Maximilian Weinmann <x1@disroot.org>
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
nvmem_cell_read return a pointer error when an error occurs. Currently
we convert the pointer error to an int while the rest of the function
return a void* and expcet an error pointer. Fix this PTR_ERR msuse
fixing compilation warning.
Fixes the following compilation warning:
net/ethernet/eth.c: In function 'nvmem_cell_get_mac_address':
net/ethernet/eth.c:547:24: warning: returning 'long int' from a function with return type 'void *' makes pointer from integer without a cast [-Wint-conversion]
547 | return PTR_ERR(mac);
| ^~~~~~~~~~~~
net/ethernet/eth.c: In function 'nvmem_cell_get_mac_address_ascii':
net/ethernet/eth.c:564:24: warning: returning 'long int' from a function with return type 'void *' makes pointer from integer without a cast [-Wint-conversion]
564 | return PTR_ERR(mac_ascii);
| ^~~~~~~~~~~~~~~~~~
Fixes: 7b863af180 ("kernel: move mac-address-ascii patches to generic")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Some Gemini devices are NAS type devices and need to ask for
DHCP IP on eth0. Some has a LAN/WAN setup. Add sensible
defaults for all known devices.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The patch managed to sneak into v5.15 whereas it was
properly deleted for v5.10.
Fixes: 8f6e2bb178 ("bcm53xx: remove MR32's specific get_leds_dt code")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Removed a20 in description, since it
only works for a10, a13 and a31.
Also refreshed kernel config.
Fixes: #10466
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
(moved fixes, refreshed, added CONFIG_DVB_USB=n)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
AddDepends/rtc has been removed in commit 3da7fe6, same here.
Fixes: 3da7fe6 ("kernel: remove useless AddDepends/rtc abstraction")
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
(RTC_SUPPORT - though this is implied by the TARGET_sunxi)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
enable option `CONFIG_CRYPTO_LZ4HC` to match default kernel config
this only adds the `lz4hc_compress` module, and has no effect on the
`lz4_decompress` module which already supports any flavor
Signed-off-by: Tony Butler <spudz76@gmail.com>
Reported by user: missing driver for USB; add to image definition
https://github.com/openwrt/openwrt/issues/11326Resolves: #11326
Signed-off-by: Tony Butler <spudz76@gmail.com>
Acked-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Make the patches apply cleanly again.
Fixes: 8327e0fb72 ("kernel: backport the dev_set_threaded export to 5.10")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This patch enables USB support for the GL.iNet GL-A1300
Repair the usb driver startup phase is not loaded
Signed-off-by: Weiping Yang <weiping.yang@gl-inet.com>
The MAC-Address setup for the Teltonika RUT230 v1 was swapped for the
LAN / WAN ports. Also the Label-MAC was assigned incorrect, as the WiFi
MAC is printed on the case as part of the SSID, however only the LAN
MAC-Address is designated as a MAC-Address.
Signed-off-by: David Bauer <mail@david-bauer.net>
add three missing LEDs
- PoE-Max
- Link/Act
- PoE
add two missing buttons
- mode
- reset
The last was dropped in
commit 61a3d0075b ("realtek: update GPIO bindings in the dts files in dts-5.10")
Signed-off-by: Jan-Niklas Burfeind <git@aiyionpri.me>
General hardware info:
----------------------
D-Link DGS-1210-28MP rev. F1 is a switch with 24 ethernet ports and 4
combo ports, all ports Gbit capable. It is based on a RTL8382 SoC @ 500MHz,
DRAM 128MB and 32MB flash. 24 ethernet ports are 802.3af/at PoE capable
with a total PoE power budget of 370W.
Power over Ethernet:
--------------------
The PSE hardware consists of three BCM59121 PSE chips, serving 8 ports
each. They are controlled by a Nuvoton MCU.
In order to enable PoE, the realtek-poe package is required. It is
installed by default, but currently it requires the manual editing of
/etc/config/poe. Keep in mind that the port number assignment does not
match on this switch, alway 8 ports are in reversed order: 8-1, 16-9 and
24-17.
LEDs and Buttons:
-----------------
On stock firmware, the mode button is supposed to switch the LED indicators
of all port LEDs between Link Activity and PoE status. The currently
selected mode is visualized using the respective LEDs. PoE Max indicates
that the maximum PoE budget has been reached.
Since there is currently no support for this behavior, these LEDs and
the mode button can be used independently.
Serial connection:
------------------
The UART for the SoC (115200 8N1) is available via unpopulated standard
0.1" pin header marked J6. Pin1 is marked with arrow and square.
Pin 1: Vcc 3.3V
Pin 2: Tx
Pin 3: Rx
Pin 4: Gnd
OEM installation from Web Interface:
------------------------------------
1. Make sure you are booting using OEM in image 2 slot. If not, switch to
image2 using the menus
System > Firmware Information > Boot from image2
Tools > reboot
2. Upload image in vendor firmware via Tools > Backup / Upgrade
Firmware > image1
3. Toogle startup image via System > Firmware Information > Boot from
image1
4. Tools > reboot
Other installation methods not tested, but since the device shares the
board with the DGS-1210-28, the following should work:
Boot initramfs image from U-Boot:
---------------------------------
1. Press Escape key during `Hit Esc key to stop autoboot` prompt
2. Press CTRL+C keys to get into real U-Boot prompt
3. Init network with `rtk network on` command
4. Load image with `tftpboot 0x8f000000
openwrt-rtl838x-generic-d-link_dgs-1210-28mp-f-initramfs-kernel.bin`
command
5. Boot the image with `bootm` command
Signed-off-by: Andreas Böhler <dev@aboehler.at>
Wavlink WS-WN572HP3 4G is an 802.11ac
dual-band outdoor router with LTE support.
Specifications;
* Soc: MT7621DAT
* RAM: 128MiB
* Flash: NOR 16MiB GD-25Q128ESIG3
* Wi-Fi:
* MT7613BEN: 5GHz
* MT7603EN: 2.4GHz
* Ethernet: 2x 1GbE
* USB: None - only used internally
* LTE Modem: Quectel EC200T-EU
* UART: 115200 baud
* LEDs:
* 7 blue at the front
* 1 Power
* 2 LAN / WAN
* 1 Status
* 3 RSSI (annotated 4G)
* 1 green at the bottom (4G LED)
* Buttons: 1 reset button
Installation:
* press and hold the reset button while powering on the device
* keep it pressed for ten seconds
* connect to 192.168.10.1 via webbrowser (chromium/chrome works, at
least Firefox 106.0.3 does not)
* upload the sysupgrade image, confirm the checksum, wait 2 minutes
until the device reboots
Revert to stock firmware:
* same as installation but use the recovery image for WL-WN572HP3
Signed-off-by: Jan-Niklas Burfeind <git@aiyionpri.me>
Acked-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Define the load-address for the DTB of all Ubiquiti UniFi devices using
FIT images. From the GPL code we can assume these boards are affected by
the same relocating issue with the vendor bootloader.
Signed-off-by: David Bauer <mail@david-bauer.net>
As the referenced MTD partition is only present in the dts, also move
&slot0 down to the dts files.
Fixes: 64e9b62829 ("mediatek: remove redundant flash entry from dtsi")
Fixes: 7dbac3433f ("mediatek: add support for reyee AX3200-E5")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Splitting-off the common parts of Ruijie RG-EW3200GX PRO and
reyee AX3200-E5 went wrong because the flash descriptiom was kept
also in the dtsi. Remove it there, as flash definition is added by
both board dts files.
Fixes: 7dbac3433f ("mediatek: add support for reyee AX3200-E5")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
1. Drop useless character '0xff' before fake filesystem header.
2. Reduce useless padding to shrink the size of the sysupgrade image.
3. Do not check the size of sysupgrade image. It does not make sense to
check the size of a compressed package.
4. Do not take the size of netgear header into account because it will
not be written to Flash.
5. Use the default lzma compression dictionary parameter '-d24' to get
better performance.
Tested on Netgear R6100
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
This is yet another model of the Ruijie RG-EW3200GX PRO with a slightly
different flash layout, install process is the same.
Specifications:
SoC: MT7622B
RAM: 256MB
Flash: XMC XM25QH128C or Winbond WQ25Q128JVSQ 16MB SPI NOR
Ethernet: 5x1GbE
Switch: MT7531BE
WiFi: 2.4G: MT7622 5G: MT7915AN+MT7975AN
3LEDs: System LED(blue) + Mesh LED(green) + Mesh LED(red)
2Keys: Mesh button + Reset button
UART: Marked J19 on board. 3.3v, 115200n1
Power: 12V 2.5A
Flash instruction:
1. Serve the initramfs.img using a TFTP server with address 10.10.10.3.
2. Interrupt the uboot startup process via UART.
3. Select "System Load Linux to SDRAM via TFTP" item.
4. (important) Back up firmware(mtd7) partitions with:
dd if=/dev/mtd7 of=/tmp/firmware.bin
and then download the firmware.bin image via SCP.
5. Flash the OpenWrt sysupgrade firmware.
Recovery stock firmware:
1. Transfer the firmware.bin image to the device.
2. Flash the image with:
mtd write firmware.bin firmware
Signed-off-by: Alex Hansen <mralexh123@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This device uses an AR8031/AR8033 chip to convert SoC gmac1
RGMII to 1000base-x or sgmii for the SFP fibre cage.
The SFP cage requires phy-mode rgmii-rxid, and without it will not
recieve any packets: ethtool -S sfp rx_fcs_errors will increase when
packets should be being received, but no other _rx counters will change.
Fixes: c77858aa79 ("ramips: mt7621-dts: change phy-mode of gmac1 to rgmii")
Reviewed-by: Robert Marko <robimarko@gmail.com>
Reviewed-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: John Thomson <git@johnthomson.fastmail.com.au>
Set CONFIG_MT6577_AUXADC=y as otherwise reading temperature of the
thermal-zone doesn't work on MT7623 (it does work fine without this
driver on MT7622 and MT7986).
Fixes: f2ae4e2f8c ("mediatek: clean up platform kernel modules")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Use ARTIFACTS to generate initramfs-based factory image of I-O DATA
WN-AX1167GR instead of redundant recipe which generate on
KERNEL_INITRAMFS.
Note:
WN-AX1167GR has 2x OS images on stock firmware.
stock log:
flash manufacture id: c2, device id 20 18
MX25L12805D(c2 2018c220) (16384 Kbytes)
mtd .name = raspi, .size = 0x01000000 (16M) .erasesize = 0x00010000 (64K) .numeraseregions = 0
Creating 10 MTD partitions on "raspi":
0x000000000000-0x000001000000 : "ALL"
0x000000000000-0x000000030000 : "Bootloader"
0x000000030000-0x000000040000 : "Config "
0x000000040000-0x000000050000 : "Factory"
0x000000050000-0x000000060000 : "iNIC_rf"
0x000000060000-0x0000007e0000 : "Kernel"
0x000000800000-0x000000f80000 : "app"
0x000000f90000-0x000000fa0000 : "Key"
0x000000fa0000-0x000000fb0000 : "backup"
0x000000fb0000-0x000001000000 : "storage"
1st image is "Kernel" and 2nd is "app" when booted from 1st image.
In OpenWrt, those 2x partitions are combined to "firmware" with
undefined (empty) areas (0x7e0000-0x7fffff, 0xf80000-0xf8ffff).
The size of an OS image partition is 0x780000 (7680 KiB = 7.5 MiB), so
check-size for initramfs-factory image needs to be called with the size.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
CPU: MediaTek MT7628AN @ 575 MHz
Flash: 16 MB
RAM: 128 MB
Ethernet: 10/100Mbps x 1
Wlan: 300 Mbps
USB: USB 2.0 x 1
LED: red/green x 1
Button: reset x 1
1. Open https://www.hiwifi.wtf/, Get Cloud token and unlock ssh
2. Upload the openwrt firmware to the router via SCP
3. Login the router via SSH
4. Run `mtd -r write path_to_firmware.bin firmware`
I have tested on my device.
- The LED will display RED on power-on, After system start completed, trun GREEN
- Reset button working now. Long press after 5s will reset factory. Short press less 1s will reboot the device
- USB can working under official u-boot
Signed-off-by: Senis John <thank243@gmail.com>
This reverts commit 5429411f73 as upstream
in commit e5f31552674e ("ethernet: fix PTP_1588_CLOCK dependencies") has
changed `PTP_1588_CLOCK` dependency handling in 5.15 kernel.
That currently leads to `CONFIG_NET_DSA_MV88E6XXX=m` in images produced
by buildbots due to `CONFIG_ALL_KMODS=y` config option being used in
those builds, which leads to a broken LAN bridge network on several
devices.
References: https://lists.infradead.org/pipermail/openwrt-devel/2022-December/039950.html
Signed-off-by: Petr Štetiar <ynezz@true.cz>
In light of https://github.com/openwrt/openwrt/issues/11077, switch mvebu
to 5.15 which has been the testing kernel on this target since April - over
half a year.
Run-tested on the following subtargets:
* cortexa9 (Turris Omnia - 03f41b1eb2)
* cortexa72 (MikroTik RB5009UG+S+IN)
Tested-by: Enrico Mioso <mrkiko.rs@gmail.com> [GL-MV1000]
Signed-off-by: Stijn Segers <foss@volatilesystems.org>
should be add/delete or abbreviated add/del
Signed-off-by: Jan-Niklas Burfeind <git@aiyionpri.me>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
The code in dsa.c:rtl83xx_port_enable() was trying to set
vlan_port_tag_sts_ctrl while dealing with differences between SoCs.
However, not only that register has a different address, the register
structure and even the 2-bit value semantic changes for each SoC.
The vlan_port_tag_sts_ctrl field was dropped and converted into a
vlan_port_keep_incoming_tag_set() function that abstracts the different
between SoCs. The macro referencing that register migrated to the SoC
specific c file as it will be privately used by each file.
All magic numbers were converted into macros using BITMASK and
FIELD_PREP.
The vlan_port_tag_sts_ctrl debugfs was dropped for now as it is already
broken for rtl93xx. The best place for SoC specific code might be in each
respective c file and not in if/else clauses.
The final result is:
rtl838x: set ITAG_STS=TAGGED, same as before
rtl839x: set ITAG_STS=TAGGED instead of IGR_P_ITAG_KEEP=0x1, fixing
forwarding of tagged packets
rtl930x: set EGR_ITAG_STS=TAGGED instead of IGR_P_ITAG=0x1, possibly
fixing forwarding of tagged packets
rtl931x: set EGR_ITAG_STS=TAGGED instead of OTPID_KEEP=0x1, possibly
fixing forwarding of tagged packets
Without (EGR_)ITAG_STS=TAGGED, at least for rtl839x, forwarded packets
will drop the vlan tag while packets from the CPU will still have the
correct tag.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
The rtl930x speed status registers require 4 bits to indicate the speed
status. As such, we want to divide by 8. To make things consistent with
the rest of this code, use a bitshift however.
This bug probably won't affect many users yet, as there aren't many
rtl930x switches in the wild yet with more then 10 ports, and thus a
low-impact bugfix.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
[also fix port field extraction]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
The Mikrotik wAP R AC is an outdoor, dual band, dual radio (802.11ac) AP
with a miniPCIe slot for a LTE modem.
The wAP R AC is similar to the wAP AC but with the miniPCIe slot.
The wAP R AC requires installing a LTE modem.
The wAP LTE and wAP LTE6 comes with a LTE modem installed.
See https://mikrotik.com/product/wap_r_ac for more info.
Specifications:
- SoC: Qualcomm Atheros IPQ4018
- CPU: 4x ARM Cortex A7
- RAM: 128MB
- Storage: 16MB NOR flash
- Wireless:
- Built-in IPQ4018 (SoC) 802.11b/g/n 2x2:2, internal antenna
- Built-in IPQ4018 (SoC) 802.11a/n/ac 2x2:2, internal antenna
- Ethernet: Built-in IPQ4018 (SoC, QCA8075) , 2x 1000/100/10 ports
one with 802.3af/at PoE in
- 1x Mini PCI-E port (USB2)
Installation:
Boot the initramfs image via TFTP, then flash the sysupgrade image using
sysupgrade. Details at https://openwrt.org/toh/mikrotik/common.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Swconfig isn't used by this target and can be disabled for
this reason. Airoha doesn't even have an Ethernet driver.
In the future, this target should get a DSA driver.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
In 8274451cb86 kmod-ppfe was changed to built-in because CONFIG_FSL_PPFE
was binary. In 5.10 and 5.15 kernel, PPFE driver can be build as module.
This patch switch kmod-ppfe from build-in to loadable module.
Loadable module helps to avoid hazard: driver is looking for firmware
file before mount root.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Let's test layerscape with 5.15 kernel.
Run tested: LS1012A-FRDM, LS1046A-RDB (nor and sd-boot images),
LS1021A-IOT (By @ArtelMike with u-boot fix)
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
At this moment LS1012A-FRDM have uncompressed initramfs image.
Error was caused, because gzip extract area overlap image.
Let's change loadaddr and enable gzip initramfs images again.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
For some reason LS1012A and LS1046A devboards don't work well with
Spansion SPI NOR flash. It cause read and write errors like:
[ 27.285887] jffs2: Newly-erased block contained word 0xc20031985 at offset 0x025ae000
[ 27.468922] jffs2: Newly-erased block contained word 0x0 at offset 0x02573000
[ 27.502615] jffs2: Newly-erased block contained word 0xe723f41e5823f110 at offset 0x02572000
[ 27.541550] jffs2: Newly-erased block contained word 0x1a7d266ee6 at offset 0x02571000
[ 27.577195] jffs2: Newly-erased block contained word 0x5d000bae8d52fec6 at offset 0x02570000
[ 27.611800] jffs2: Newly-erased block contained word 0x63515aee63515a4b at offset 0x0256f000
[ 27.651749] jffs2: Newly-erased block contained word 0xc20031985 at offset 0x0256e000
[ 27.825593] jffs2: Newly-erased block contained word 0xc20031985 at offset 0x0252e000
NXP have found workarround and applied in their vendor kernel version.
They force 1x tx and 1x rx lines in qspi. That method fix issues.
This patch ports patches from NXP LSDK tree.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
- Bring back factory.bin image which was missing after porting device to ath79 target
- Use default sysupgrade.bin image recipe
- Adjust max image size according to new firmware partition size after
"ath79: expand rootfs for DIR-825-B1 with unused space (aca8bb5)" changes
- Remove support of upgrading from version 19.07, because partition size changes mentioned above
Signed-off-by: Will Moss <willormos@gmail.com>
FCC ID: A8J-EAP1750H
Engenius EAP1750H is an indoor wireless access point with
1 Gb ethernet port, dual-band wireless,
internal antenna plates, and 802.3at PoE+
**Specification:**
- QCA9558 SOC
- QCA9880 WLAN PCI card, 5 GHz, 3x3, 26dBm
- AR8035-A PHY RGMII GbE with PoE+ IN
- 40 MHz clock
- 16 MB FLASH MX25L12845EMI-10G
- 2x 64 MB RAM NT5TU32M16FG
- UART at J10 populated
- 4 internal antenna plates (5 dbi, omni-directional)
- 5 LEDs, 1 button (power, eth0, 2G, 5G, WPS) (reset)
**MAC addresses:**
MAC addresses are labeled as ETH, 2.4G, and 5GHz
Only one Vendor MAC address in flash
eth0 ETH *:fb art 0x0
phy1 2.4G *:fc ---
phy0 5GHz *:fd ---
**Serial Access:**
the RX line on the board for UART is shorted to ground by resistor R176
therefore it must be removed to use the console
but it is not necessary to remove to view boot log
optionally, R175 can be replaced with a solder bridge short
the resistors R175 and R176 are next to the UART RX pin at J10
**Installation:**
2 ways to flash factory.bin from OEM:
Method 1: Firmware upgrade page:
OEM webpage at 192.168.1.1
username and password "admin"
Navigate to "Firmware Upgrade" page from left pane
Click Browse and select the factory.bin image
Upload and verify checksum
Click Continue to confirm and wait 3 minutes
Method 2: Serial to load Failsafe webpage:
After connecting to serial console and rebooting...
Interrupt uboot with any key pressed rapidly
execute `run failsafe_boot` OR `bootm 0x9fd70000`
wait a minute
connect to ethernet and navigate to
"192.168.1.1/index.htm"
Select the factory.bin image and upload
wait about 3 minutes
**Return to OEM:**
If you have a serial cable, see Serial Failsafe instructions
otherwise, uboot-env can be used to make uboot load the failsafe image
ssh into openwrt and run
`fw_setenv rootfs_checksum 0`
reboot, wait 3 minutes
connect to ethernet and navigate to 192.168.1.1/index.htm
select OEM firmware image from Engenius and click upgrade
**TFTP recovery:**
Requires serial console, reset button does nothing
rename initramfs to 'vmlinux-art-ramdisk'
make available on TFTP server at 192.168.1.101
power board, interrupt boot
execute tftpboot and bootm 0x81000000
NOTE: TFTP is not reliable due to bugged bootloader
set MTU to 600 and try many times
if your TFTP server supports setting block size
higher block size is better.
**Format of OEM firmware image:**
The OEM software of EAP1750H is a heavily modified version
of Openwrt Kamikaze. One of the many modifications
is to the sysupgrade program. Image verification is performed
simply by the successful ungzip and untar of the supplied file
and name check and header verification of the resulting contents.
To form a factory.bin that is accepted by OEM Openwrt build,
the kernel and rootfs must have specific names...
openwrt-ar71xx-generic-eap1750h-uImage-lzma.bin
openwrt-ar71xx-generic-eap1750h-root.squashfs
and begin with the respective headers (uImage, squashfs).
Then the files must be tarballed and gzipped.
The resulting binary is actually a tar.gz file in disguise.
This can be verified by using binwalk on the OEM firmware images,
ungzipping then untaring.
Newer EnGenius software requires more checks but their script
includes a way to skip them, otherwise the tar must include
a text file with the version and md5sums in a deprecated format.
The OEM upgrade script is at /etc/fwupgrade.sh.
OKLI kernel loader is required because the OEM software
expects the kernel to be no greater than 1536k
and the factory.bin upgrade procedure would otherwise
overwrite part of the kernel when writing rootfs.
Note on PLL-data cells:
The default PLL register values will not work
because of the external AR8035 switch between
the SOC and the ethernet port.
For QCA955x series, the PLL registers for eth0 and eth1
can be see in the DTSI as 0x28 and 0x48 respectively.
Therefore the PLL registers can be read from uboot
for each link speed after attempting tftpboot
or another network action using that link speed
with `md 0x18050028 1` and `md 0x18050048 1`.
The clock delay required for RGMII can be applied
at the PHY side, using the at803x driver `phy-mode`.
Therefore the PLL registers for GMAC0
do not need the bits for delay on the MAC side.
This is possible due to fixes in at803x driver
since Linux 5.1 and 5.3
Signed-off-by: Michael Pratt <mcpratt@pm.me>
Driver for and pci wlan card now pull the calibration data from the nvmem
subsystem.
This allows us to move the userspace caldata extraction for the pci-e ath9k
supported wifi into the device-tree definition of the device.
The wifi mac address remains correct after these changes, because When both
"mac-address" and "calibration" are defined, the effective mac address
comes from the cell corresponding to "mac-address" and
mac-address-increment.
Test passed on my tplink tl-wr2543nd.
Signed-off-by: Edward Chow <equu@openmail.cc>
Manually rebased: ath79/patches-5.10/910-unaligned_access_hacks.patch
All other patches automatically rebased.
Signed-off-by: John Audia <therealgraysky@proton.me>
It was tested that cache scaling currently cause instability problem.
This is probably caused by a latent misconfiguration that cause the L2
cache to be sourced from the wrong source and runs at an unstable freq
compared to the original QSDK fw.
To improve stability while the problem is bisected, disable the devfreq
drivers with minimal perf penality.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The CDMQ ingress special tag flag needs to be set for 7986 even without DSA
untag offload, otherwise tx checksum offload seems to break
Fixes: 9b482ee22f ("kernel: add more fixes for mtk_eth_soc")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Use persistent MAC address for the built-in wireless interfaces of the
BPi-R64 and BPi-R3 development boards.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The type of those images is already distinguishable by the '.itb'
extension, there is no need for an additional '-fit' string in the
filenames. Remove it to behave more like other targets.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Only on the ipq40xx subtarget different filenames were used for NAND-
based devices. This is unneeded, confusing and breaks downstream tools
such as luci-app-attendedsysupgrade and auc.
Remove the 'nand-' string from image filenames to fix that.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Enabling both CONFIG_MMC_BCM2835 and CONFIG_MMC_BCM2835_SDHOST causes this
error in dmesg:
Error: Driver 'sdhost-bcm2835' is already registered, aborting...
Disabling CONFIG_MMC_BCM2835 and leaving CONFIG_MMC_BCM2835_SDHOST enabled
avoids this error.
Build-tested: bcm2711/RPi4B
Run-tested: bcm2711/RPi4B
Signed-off-by: John Audia <therealgraysky@proton.me>
[Disable driver for all subtargets, refresh configs, tweak description]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
The CDMQ ingress special tag flag needs to be set for 7986 even without DSA
untag offload, otherwise tx checksum offload seems to break
Fixes: 9b482ee22f ("kernel: add more fixes for mtk_eth_soc")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Protect the flow block cb list readers against concurrent updates
Reported-by: Chad Monroe <chad.monroe@smartrg.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Keenetic KN-3010 is a 2.4/5 Ghz band 11ac (Wi-Fi 5) router, based on MT7621DAT.
Specification:
- System-On-Chip: MT7621DAT
- CPU/Speed: 880 MHz
- Flash-Chip: Winbond w25q256
- Flash size: 32768 KiB
- RAM: 128 MiB
- 5x 10/100/1000 Mbps Ethernet
- 4x external, non-detachable antennas
- UART (J1) header on PCB (115200 8n1)
- Wireless No1 (2T2R): MT7603E 2.4 GHz 802.11bgn
- Wireless No2 (2T2R): MT7613BE 5 GHz 802.11ac
- 4x LED, 2x button, 1x mode switch
Notes:
- The device supports dual boot mode
- The firmware partitions were concatinated into one
- The FN button led indicator has been reassigned as the 2.4GHz
wifi indicator.
Flash instruction:
The only way to flash OpenWrt image is to use tftp recovery mode in U-Boot:
1. Configure PC with static IP 192.168.1.2/24 and tftp server.
2. Rename "openwrt-ramips-mt7621-keenetic_kn-3010-squashfs-factory.bin"
to "KN-3010_recovery.bin" and place it in tftp server directory.
3. Connect PC with one of LAN ports, press the reset button, power up
the router and keep button pressed until power led start blinking.
4. Router will download file from server, write it to flash and reboot.
Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
Intel PINCTRL is not enable in the 64bit build, while it is enabled in
the x86/general target, which disables the ability of controlling GPIO
in the 64 bit build.
This commit copies the corresponding part of x86/general config, since
it is already there, so it should be fine to enable the same settings
here.
Signed-off-by: Xiaopo Zhang <xiaopoz@proton.me>
On TP-Link TL-WR740N/TL-WR741ND v4 LAN MAC address (eth1 in DTS) is main
device MAC address, so do not increment it. WAN MAC is LAN MAC + 1.
Signed-off-by: Will Moss <willormos@gmail.com>
The downstream OpenWrt driver for the BCM53128 switch ceased to work,
rendering the 8 LAN ports of the device unusable. This commit disables
image building while the problem is being solved.
See issue #10374 for more details.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Driver for both soc (2.4GHz Wifi) and pci (5 GHz) now pull the calibration
data from the nvmem subsystem.
This allows us to move the userspace caldata extraction for the pci-e ath9k
supported wifi into the device-tree definition of the device.
wmac's nodes are also changed over to use nvmem-cells over OpenWrt's
custom mtd-cal-data property.
The wifi mac address remains correct after these changes, because When both
"mac-address" and "calibration" are defined, the effective mac address
comes from the cell corresponding to "mac-address" and
mac-address-increment.
Test passed on my wndr3700v4 and wndr4500v3.
Signed-off-by: Edward Chow <equu@openmail.cc>
Performance comparison (iperf3, mtu 1500):
Before: 53.9 Mbps
After: 87.9 Mbps
The tests were performed on a BT Home Hub 5A router.
The iperf3 server was running on the router, the client
on the host.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Enabled CONFIG_MIPS_MT_SMP and CONFIG_SCHED_SMT.
Tested on FRITZ!Box 7330 SL, 7312 and o2 Box 4421.
Signed-off-by: Christian Buschau <christian.buschau@mailbox.org>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Fixes leftover TODO from commit 6bf179b270
Signed-off-by: Christian Buschau <christian.buschau@mailbox.org>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Run of 'make kernel_oldconfig CONFIG_TARGET=subtarget'
Signed-off-by: Christian Buschau <christian.buschau@mailbox.org>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Driver for both soc (2.4GHz Wifi) and pci (5 GHz) now pull the calibration
data from the nvmem subsystem.
This allows us to move the userspace caldata extraction for the pci-e ath9k
supported wifi into the device-tree definition of the device.
wmac's nodes are also changed over to use nvmem-cells over OpenWrt's
custom mtd-cal-data property.
The wifi mac address remains correct after these changes, because When both
"mac-address" and "calibration" are defined, the effective mac address
comes from the cell corresponding to "mac-address" and
mac-address-increment.
Test passed on my tplink tl-wdr4310.
Signed-off-by: Edward Chow <equu@openmail.cc>
The mt7623 subtarget supports 2 devices:
* Bananapi BPi-R2 (added in 1f068588ef, 7762c07c88),
* UniElec U7623-02 (added in 4def81f30f).
Both devices support DSA from the beginning, thus
swconfig can be safely disabled.
In the past, the subtarget mt7623 also supported
the mt7623 reference board. This board originally
supported swconfig, and was later converted to DSA
(64175ffb79) and then dropped (1ab81bf02d).
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
While compiling OpenWrt master for Turris 1.x routers (p2020), it
reported following error:
Gianfar Ethernet (GIANFAR) [Y/n/m/?] y
Freescale DPAA2 Ethernet Switch (FSL_DPAA2_SWITCH) [N/m/y/?] (NEW)
Error in reading or end of file.
Let's fix it by disabling it.
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
NVRAM packages for the same wireless chip are consolidated into one as
they contain only small text files and symlinks.
Signed-off-by: Kuan-Yi Li <kyli@abysm.org>
NVRAM packages for the same wireless chip are consolidated into one as
they contain only small text files and symlinks.
Signed-off-by: Kuan-Yi Li <kyli@abysm.org>
