Fix style of nvmem cell names in the device tree of the GL.iNet MT-2500.
Fixes: 49ed52b862 ("mediatek: filogic: convert GL.iNet MT-2500 to use NVMEM-on-MMC)"
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Recent OEM firmware versions test the version number embedded in the uimage
"name" header field. The exact restricton is unknown, but "7.0.8.4" seems
to be the lowest number accepted on a GS110TPPv1 which already has that
version or higher.
A "9.9.9.9" version is accepted as valid by the GS110TPPv1 OEM firmware,
and considered both unique enough to identify an OpenWrt image and
moderately future proof against OEM version bumps.
This change is also boot tested on a GS108Tv3 with
"BOOT Loader Version 1.0.0.2 (2018-08-31 17:05:26 UTC)"
to verify that it doesn't break boot on older hardware.
Link: https://forum.openwrt.org/t/72510/58
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Import patch to make sure SGM_REG_SEL clock is always enabled as it
seems that more registers than just SGMIISYS0 and SGMIISYS1 are
depending on that clock being enabled.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Now that we can reference MMC partitions in device tree, use that
to get rid of Wi-Fi EEPROM and MAC address setup in userspace.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Use device_set_node to make sure OF node gets assigned on block
devices to be used as NVMEM providers. While block partitions were
already working fine as NVMEM providers, bare block devices such as
mmcblk0boot1 will not work without this change.
Fixes: fc153aa8d9 ("kernel: import pending patches adding support for NVMEM on UBI and MMC")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
UNIPHY2 on the WAX630 is connected to a QCA8081 PHY which is only 2.5G and
it does not support using USXGMII at all but rather only SGMII or SGMII+.
Tested-by: Kristian Skramstad <kristian+github@83.no>
Signed-off-by: Robert Marko <robimarko@gmail.com>
Remove inaccurate compatible string 'mediatek,mt7986-ethsys' which
results in the wrong clock driver probing on MT7981 with Linux 6.1 and
ends up freezing the system once WED is used.
Fixes: da970d63fb ("mediatek: switch to Linux version 6.1")
Reported-by: Chen Minqiang <ptpt52@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Some Aquantia PHYs (e.g. AQR113C) require firmware to be uploaded by
host system. With built-in drivers this doesn't work in OpenWrt /
embeddded as filesystem isn't available during PHY probe. That results
in delays like:
[ 1.588068] Aquantia AQR113C mdio-bus:00: Falling back to sysfs fallback for: Rhe-05.06-Candidate9-AQR_Mediatek_23B_P5_ID45824_LCLVER1.cld
[ 64.526387] Aquantia AQR113C mdio-bus:00: failed to find FW file Rhe-05.06-Candidate9-AQR_Mediatek_23B_P5_ID45824_LCLVER1.cld (-110)
Switch to module to postpone PHY probe to init state.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Interfaces that have AQR-s attached to them are using USXGMII and not just
the default SGMII.
This was fine until SSDK added some sanity checking and now on Qnap 301W it
would fail with:
[ 24.740197] nss-dp 3a001800.dp5 10g-1 (uninitialized): failed to connect to phy device
[ 24.740264] nss-dp: probe of 3a001800.dp5 failed with error -14
Since this is not Qnap 301W specific lets fix it subtarget wide by
declaring the correct PHY mode for 10G AQR-s.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Interfaces that have AQR-s attached to them are using USXGMII and not just
the default SGMII.
This was fine until SSDK added some sanity checking and now on Qnap 301W it
would fail with:
[ 24.740197] nss-dp 3a001800.dp5 10g-1 (uninitialized): failed to connect to phy device
[ 24.740264] nss-dp: probe of 3a001800.dp5 failed with error -14
So, lets fix 10G AQR ports by declaring the correct PHY mode.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Also here build fails due to increased kernel size.
Fixes: da970d63fb ("mediatek: switch to Linux version 6.1")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Building a package in the build system or the SDK results in different
values for the `SOURCE` property, it's either `packages/<package name>`
or `feeds/base/<package name>`. The reason is that the SDK handles
`openwrt.git` as an external feed called while the build system contains
the *base* packages directly.
Since packages created with either method are (ideally) the same (bit
for bit), align the content of SOURCE. To do so this commit creates a
symlink from `feeds/base` to `$(TOPDIR)/package` and adopts the SOURCE
when building from inside the build system.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Due to increased kernel size the build currently fails if including
the MT7622 rfb1 (UBI). Skip it for now until there is a better
solution (such as replacing the bootloader and changing the flash
layout).
Fixes: da970d63fb ("mediatek: switch to Linux version 6.1")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Include the needed Ethernet PHY driver module for the BananaPi R3 mini.
Fixes: b03d3644cf ("mediatek: filogic: add BananaPi BPi-R3 mini")
Reported-by: BPI forum user nezar_taima
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Let ubinize-image append the ubinized image to the existing image
instead of replacing it.
Fixes: 6c17d71973 ("scripts: ubinize-image.sh: support static volumes, make size optional")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
One of the pins requiered by M.2 slot is conflict with spi1,
however, spi1 seems unused so simply disable it for now, this
matches the factory behavior [1].
1. 9bd78779f2
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Conversion to new LED color/function format and drop label format.
This was needed previously when the new format wasn't supported by
leds.sh functions script. Now that is supported this property can be
removed in favor of the new format.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
This commit fixes the alphabetical order in 02_network.
The 2 deco devices in ath79_setup_interfaces() were in the wrong place.
Signed-off-by: Foica David <superh552@gmail.com>
Since we can configure the PHY LED of the qca8081,
add a configuration for this device.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Reviewed-by: Robert Marko <robimarko@gmail.com>
The dts of Arcadyan AW1000 forgot to convert qca807x PHY
to PHY package implementation. This commit fix it.
Fixes: 0ab4b92 ("qualcommax: convert qca807x PHY to PHY package implementation")
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Reviewed-by: Robert Marko <robimarko@gmail.com>
By default opkg sets the "user" flag when a package is installed,
which resulted in most packages in the rootfs having this flag
set incorrectly. This patch removes the "user" flag from all
installed packages when preparing the rootfs image.
Fixes: #14427
Signed-off-by: Justin Klaassen <justin@tidylabs.app>
Generate ubinized image as ARTIFACT and make use of now available
generic 'ubinize-image' build step intended for that purpose.
Fixes: b03d3644cf ("mediatek: filogic: add BananaPi BPi-R3 mini")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Fix NAND flash layout which was out-of-sync with the definition in
ARM TrustedFirmware-A which expects UBI to start at 0x200000.
Fixes: b03d3644cf ("mediatek: filogic: add BananaPi BPi-R3 mini")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Make sure ubinize-image.sh also works with more simple POSIX Shell and
allow creating complete custom images to be used as ARTIFACT/foo.img
and thereby allow including uImage.FIT, TF-A FIP and what ever else
is required on a specific board.
Fixes: 6c17d71973 ("scripts: ubinize-image.sh: support static volumes, make size optional")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The U-Boot binary for the RAVPower RP-WD009 has been renamed.
In order to be uniform with all other U-Boot binaries generated the SoC type has been prepended.
Set that new name also in the image build recipe for that device in order to fix build.
Fixes: 927334a8f7 ("uboot-mediatek: add basic build for ZBT-WG3526 (MT7621, 16M SPI-NOR)")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
update the default network configuration for Gateworks Ventana boards
such that the left-most front-panel NIC is WAN and any additional are in
LAN bridge
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Hardware specification
----------------------
SoC: MediaTek MT7986A 4x A53
Flash: 128MB SPI-NAND, 8GB eMMC
RAM: 2GB DDR4
Ethernet: 2x 2.5GbE (Airoha EN8811H)
WiFi: MediaTek MT7976C 2x2 2.4G + 3x3 5G
Interfaces:
* M.2 Key-M: PCIe 2.0 x2 for NVMe SSD
* M.2 Key-B: USB 3.0 with SIM slot
* front USB 2.0 port
LED: Power, Status, WLAN2G, WLAN5G, LTE, SSD
Button: Reset, internal boot switch
Fan: PWM-controlled 5V fan
Power: 12V Type-C PD
Installation instructions for eMMC
----------------------------------
0. Set boot switch to boot from SPI-NAND (assuming stock rom or immortalwrt
running there).
1. Write GPT partition table to eMMC
Move openwrt-mediatek-filogic-bananapi_bpi-r3-mini-emmc-gpt.bin to
the device /tmp using scp and write it to /dev/mmcblk0:
dd if=/tmp/openwrt-*-r3-mini-emmc-gpt.bin of=/dev/mmcblk0
2. Reboot (to reload partition table)
3. Write bootloader and OpenWrt images
Move files to the device /tmp using scp:
- openwrt-*-bananapi_bpi-r3-mini-emmc-preloader.bin
- openwrt-*-bananapi_bpi-r3-mini-emmc-bl31-uboot.fip
- openwrt-*-bananapi_bpi-r3-mini-initramfs-recovery.itb
- openwrt-*-bananapi_bpi-r3-mini-squashfs-sysupgrade.itb
Write them to the appropriate partitions:
echo 0 > /sys/block/mmcblk0boot0/force_ro
dd if=/tmp/openwrt-*-bananapi_bpi-r3-mini-emmc-preloader.bin of=/dev/mmcblk0boot0
dd if=/tmp/openwrt-*-bananapi_bpi-r3-mini-emmc-bl31-uboot.fip of=/dev/mmcblk0p3
dd if=/tmp/openwrt-*-bananapi_bpi-r3-mini-initramfs-recovery.itb of=/dev/mmcblk0p4
dd if=/tmp/openwrt-*-bananapi_bpi-r3-mini-squashfs-sysupgrade.itb of=/dev/mmcblk0p5
sync
4. Remove the device from power, set boot switch to eMMC and boot into
OpenWrt. The device will come up with IP 192.168.1.1 and assume the
Ethernet port closer to the USB-C power connector as LAN port.
5. If you like to have Ethernet support inside U-Boot (eg. to boot via
TFTP) you also need to write the PHY firmware to /dev/mmcblk0boot1:
echo 0 > /sys/block/mmcblk0boot1/force_ro
dd if=/lib/firmware/airoha/EthMD32.dm.bin of=/dev/mmcblk0boot1
dd if=/lib/firmware/airoha/EthMD32.DSP.bin bs=16384 seek=1 of=/dev/mmcblk0boot1
Installation instructions for NAND
----------------------------------
0. Set boot switch to boot from eMMC (assuming OpenWrt is installed there
by instructions above. Using stock rom or immortalwrt does NOT work!)
1. Write things to NAND
Move files to the device /tmp using scp:
- openwrt-*-bananapi_bpi-r3-mini-snand-preloader.bin
- openwrt-*-bananapi_bpi-r3-mini-snand-bl31-uboot.fip
- openwrt-*-bananapi_bpi-r3-mini-initramfs-recovery.itb
- openwrt-*-bananapi_bpi-r3-mini-squashfs-sysupgrade.itb
Write them to the appropriate locations:
mtd write /tmp/openwrt-*-bananapi_bpi-r3-mini-snand-preloader.bin /dev/mtd0
ubidetach -m 1
ubiformat /dev/mtd1
ubiattach -m 1
volsize=$(wc -c < /tmp/openwrt-*-bananapi_bpi-r3-mini-snand-bl31-uboot.fip)
ubimkvol /dev/ubi0 -N fip -n 0 -s $volsize -t static
ubiupdatevol /dev/ubi0_0 /tmp/openwrt-*-bananapi_bpi-r3-mini-snand-bl31-uboot.fip
cd /lib/firmware/airoha
cat EthMD32.dm.bin EthMD32.DSP.bin > /tmp/en8811h-fw.bin
ubimkvol /dev/ubi0 -N en8811h-firmware -n 1 -s 147456 -t static
ubiupdatevol /dev/ubi0_1 /tmp/en8811h-fw.bin
ubimkvol /dev/ubi0 -n 2 -N ubootenv -s 126976
ubimkvol /dev/ubi0 -n 3 -N ubootenv2 -s 126976
volsize=$(wc -c < /tmp/openwrt-*-bananapi_bpi-r3-mini-initramfs-recovery.itb)
ubimkvol /dev/ubi0 -n 4 -N recovery -s $volsize
ubiupdatevol /dev/ubi0_4 /tmp/openwrt-*-bananapi_bpi-r3-mini-initramfs-recovery.itb
volsize=$(wc -c < /tmp/openwrt-*-bananapi_bpi-r3-mini-squashfs-sysupgrade.itb)
ubimkvol /dev/ubi0 -n 4 -N recovery -s $volsize
ubiupdatevol /dev/ubi0_4 /tmp/openwrt-*-bananapi_bpi-r3-mini-squashfs-sysupgrade.itb
3. Remove the device from power, set boot switch to NAND, power up and
boot into OpenWrt.
Partially based on immortalwrt support for the R3 mini, big thanks for
doing the ground work!
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add PHY driver for Airoha EN8811H PHY and package it as kernel module.
The PHY needs to load firmware from rootfs, so there is no point in
having the driver built-into the kernel.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The R3 mini comes with two Airoha EN8811H PHYs for 2.5G Ethernet.
The driver added to U-Boot expects the firmware for the PHY to be
stored inside UBI volume en8811h-fw or MMC boot1 hardware partition.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add package with firmware for Airoha EN8811H 2.5G Ethernet PHY which
needs to be loaded via MDIO before the PHY can be used.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
In order to support devices having TF-A FIP image or UBI-aware U-Boot
SPL we need to include a static volume for the bootloader.
Introduce support for adding additional static volumes by prefixing
the filename with ':', eg.
UBINIZE_PARTS := fip:=$(STAGING_DIR_IMAGE)/u-boot.fip
Also add support for rootfs-in-uImage.FIT setups which don't require a
rootfs partition and make the (3rd) size parameter in UBINIZE_PARTS
optional (see example above without declared size).
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Firmware for the built-in 2.5G Ethernet PHY of the MediaTek MT7988 SoC
is now part of linux-firmware, so we can package it.
Only a single file is needed with recent driver.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Move fip and factory into UBI static volumes.
Use fitblk instead of partition parser.
!! RUN INSTALLER FIRST !!
Existing users of previous OpenWrt releases or snapshot builds will
have to **re-run the updated installer** before upgrading to firmware
after this commit.
DO NOT flash or run even just the initramfs image unless you have
run the updated installer which moves the content of the 'factory'
partition into a UBI volume.
tl;dr: DON'T USE YET!
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
