Commit Graph

766 Commits

Author SHA1 Message Date
David Bauer
c9cb6411c1 mediatek: add support for Cudy WR3000 v1
Hardware
--------
MediaTek MT7981 WiSoC
256MB DDR3 RAM
16MB SPI-NOR (XMC XM25QH128C)
MediaTek MT7981 2x2 DBDC 802.11ax 2T2R (2.4 / 5)
UART: 115200 8N1 3.3V
      [LEDS] VCC-GND-RX-TX [ETH]
      Header is located below the heatsink

Case
----
Unscrew the 4 bottom screws. Remove the top of the case by inserting a
small screwdriver into the ventilation holes and lift the top cover.

This works best by beginning near the ETH-ports. The top is clipped on
the front near the LEDs with two plastic clips. The back has a single
clip in the middle. Start at one of the back edges.

MAC-Addresses
-------------
80:AF:CA:00:F9:C6 LAN
80:AF:CA:00:F9:C7 WAN
80:AF:CA:00:F9:C6 W2
82:AF:CA:30:F9:C6 W5

Installation
------------

1. Connect to the serial port as described in the "Hardware" section.

2. Power on the device. Keep pressing the "0" key to enter the U-Boot
   shell.

3. Download the OpenWrt initramfs image. Place it on an TFTP server
   connected to the Cudy LAN ports. Make sure the server is reachable at
   192.168.1.2. Rename the image to "cudy3000.bin"

4. Download and boot the OpenWrt initramfs image.

   $ tftpboot 0x46000000 cudy3000.bin; bootm 0x46000000

5. Transfer the OpenWrt sysupgrade image to the device using scp.
   Install with sysupgrade.

Note: Cudy does not yet provide a image for disabling their
signature-protection. This has happened in the past. Make sure to check
the wiki for a possible easier installation method.

Signed-off-by: David Bauer <mail@david-bauer.net>
2023-05-18 01:46:13 +02:00
David Bauer
9fa4aa63c5 mediatek: fix typo
Signed-off-by: David Bauer <mail@david-bauer.net>
2023-05-18 01:42:52 +02:00
Daniel Golle
ff5d08799b generic: add support for wireless offloading on MT7981
Load appropriate firmware for wireless offloading on MT7981.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-05-15 20:55:39 +02:00
John Audia
228e0e1039 kernel: bump 5.15 to 5.15.111
Removed upstreamed:
	01. backport-5.15/424-v6.4-0001-mtd-core-provide-unique-name-for-nvmem-device-take-t.patch
	02. backport-5.15/424-v6.4-0002-mtd-core-fix-nvmem-error-reporting.patch
	03. generic-backport/424-v6.4-0003-mtd-core-fix-error-path-for-nvmem-provider.patch
	04. generic-backport/828-v6.4-0001-of-Fix-modalias-string-generation.patch
	05. bcm4908/patches-5.15/031-v5.17-0002-arm64-dts-broadcom-bcm4908-add-DT-for-Netgear-RAXE50.patch
	06. bcm4908/patches-5.15/033-v6.0-0001-arm64-dts-Add-DTS-files-for-bcmbca-SoC-BCM63158.patchgit
	07. bcm4908/patches-5.15/033-v6.0-0002-arm64-dts-Add-DTS-files-for-bcmbca-SoC-BCM4912.patchgita
	08. bcm4908/patches-5.15/033-v6.0-0010-arm64-dts-Add-base-DTS-file-for-bcmbca-device-Asus-G.patchgit
	09. bcm4908/patches-5.15/034-v6.1-0005-arm64-dts-Move-BCM4908-dts-to-bcmbca-folder.patch
	10. bcm4908/patches-5.15/036-v6.4-0002-arm64-dts-broadcom-bcmbca-bcm4908-fix-NAND-interrupt.patch
	11. bcm4908/patches-5.15/036-v6.4-0004-arm64-dts-broadcom-bcmbca-bcm4908-fix-procmon-nodena.patch
	12. ipq806x/patches-5.15/104-v6.0-06-ARM-dts-qcom-ipq8064-reduce-pci-IO-size-to-64K.patch

Manually rebased:
	bcm27xx/patches-5.15/950-0078-BCM2708-Add-core-Device-Tree-support.patch
	bcm27xx/patches-5.15/950-0547-ARM-dts-Add-Pi-Zero-2-support.patch
	bcm4908/patches-5.15/033-v6.0-0001-arm64-dts-Add-DTS-files-for-bcmbca-SoC-BCM63158.patchgit
	bcm4908/patches-5.15/033-v6.0-0002-arm64-dts-Add-DTS-files-for-bcmbca-SoC-BCM4912.patchgit
	bcm4908/patches-5.15/030-v5.16-0001-arm64-dts-broadcom-bcm4908-Fix-NAND-node-name.patch
	bcm4908/patches-5.15/032-v5.18-0002-arm64-dts-broadcom-bcm4908-add-pinctrl-binding.patch
	bcm4908/patches-5.15/032-v5.18-0003-arm64-dts-broadcom-bcm4908-add-watchdog-block.patch
	bcm4908/patches-5.15/032-v5.18-0004-arm64-dts-broadcom-bcm4908-add-I2C-block.patch
	bcm4908/patches-5.15/033-v6.0-0003-ARM64-dts-Add-DTS-files-for-bcmbca-SoC-BCM6858.patchgit
	bcm4908/patches-5.15/033-v6.0-0008-arm64-dts-broadcom-bcm4908-Fix-timer-node-for-BCM490.patchgit
	bcm4908/patches-5.15/034-v6.1-0001-arm64-dts-broadcom-bcm4908-add-remaining-LED-pins.patch
	bcm4908/patches-5.15/034-v6.1-0002-arm64-dts-broadcom-bcm4908-add-LEDs-controller-block.patch
	bcm4908/patches-5.15/034-v6.1-0003-arm64-dts-broadcom-bcm4908-add-Asus-GT-AC5300-LEDs.patch
	bcm4908/patches-5.15/034-v6.1-0004-arm64-dts-bcmbca-update-BCM4908-board-dts-files.patch

All other patches automatically rebased.

Build system: x86_64
Build-tested: bcm2711/RPi4B, ramips/tplink_archer-a6-v3, filogic/xiaomi_redmi-router-ax6000-ubootmod
Run-tested: bcm2711/RPi4B, ramips/tplink_archer-a6-v3, filogic/xiaomi_redmi-router-ax6000-ubootmod

01. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.111&id=77112d23a671697f0f70695ab901f807e15d2093
02. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.111&id=fe07b3b5af01f42b291f5da0da09d047f50b33a6
03. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.111&id=273be36e420924237f6c9d43cdad96718c13dd52
04. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.111&id=fe8ab85ed4958e58e991bba0aa0a655b552b0273
05. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.111&id=6ae67829fa5e9e71f458f69db42f0e216225616a
06. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.111&id=1994284cb9226b65ca3a6744ce3320218b584f26
07. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.111&id=a46878476c5549a4fde15a31922ce80a50b23492
08. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.111&id=112ff0f2530549d50510f116474924f9c4fad590
09. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.111&id=7c253e98685e6d884d12e2618ef4d2ad90b4fbd7
10. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.111&id=8444b46e163aa9559a0af0381a1d230ec4146eb2
11. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.111&id=6d1af517817a760d7af3dee0fc4603645485495c
12. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.111&id=cc4f0e168a5630ad0491ac5328f1a89f3cf3d04e

Signed-off-by: John Audia <therealgraysky@proton.me>
2023-05-13 22:38:35 +02:00
David Bauer
7890dd75ad ramips: fix mt7621 kernel compilation
The OF LED configuration patch fails on MT7621, as the necessary headers
were only included for the mediatek subtarget with an additional patch.

Fixes: 242fe8634e ("generic: add hack for MT753x LED configuration")

Signed-off-by: David Bauer <mail@david-bauer.net>
2023-05-12 09:38:58 +02:00
David Bauer
0ce356bbba mediatek: apply stock configuration for WAN-LED
Apply the same LED configuration used by the vendor-firmware for the
GPY211 controlled WAN LED in OpenWrt.

Signed-off-by: David Bauer <mail@david-bauer.net>
2023-05-11 23:09:04 +02:00
David Bauer
3492517f37 mediatek: configure TUF-AX4200 LAN LEDs
As we can now configure the switch LED configuration, write the switch
LED configuration values from the vendor firmware to the switch-IC.

Previously, the switch-LEDs did not show any acitvity or link-status
whatsoever.

Signed-off-by: David Bauer <mail@david-bauer.net>
2023-05-11 23:09:04 +02:00
Lu jicong
1645c34d56
generic: enable CONFIG_ARM_CRYPTO for 32bit arm targets
Fix following error when building 32bit arm targets with kmod-crypto-sha512
ERROR: module '/home/user/openwrt/build_dir/target-arm_xscale_musl_eabi/linux-kirkwood_generic/linux-5.15.109/arch/arm/crypto/sha512-arm.ko' is missing.

Signed-off-by: Lu jicong <jiconglu58@gmail.com>
2023-05-10 19:01:45 +02:00
Lu jicong
d246cb89da
generic: refresh 5.15 kernel config
prepare for enabling CONFIG_ARM_CRYPTO on these targets

Signed-off-by: Lu jicong <jiconglu58@gmail.com>
2023-05-10 19:01:45 +02:00
Tony Ambardar
3d66f55161 kernel: improve handling of CONFIG_IO_URING
Kernel setting CONFIG_IO_URING supports high-performance I/O for file
access and servers, generally for more performant platforms, and adds
~45 KB to kernel sizes. The need for this on less "beefy" devices is
questionable, as is the size cost considering many platforms have kernel
size limits which require tricky repartitioning if outgrown. The size
cost is also large relative to the ~180 KB bump expected between major
OpenWRT kernel releases.

No OpenWrt packages have hard dependencies on this; samba4 and mariadb
can take advantage if available (+KERNEL_IO_URING:liburing) but
otherwise build and work fine.

Since CONFIG_IO_URING is already managed via the KERNEL_IO_URING setting
in Config-kernel.in (default Y), remove it from those target configs
which unconditionally enable it, and update the defaults to enable it
conditionally only on more powerful 64-bit x86 and arm devices. It may
still be manually enabled as needed for high-performance custom builds.

Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
2023-05-03 10:26:17 -07:00
Tony Ambardar
3980dfcd05 kernel: fix handling of CONFIG_DYNAMIC_DEBUG
Since CONFIG_DYNAMIC_DEBUG is already managed via the KERNEL_DYNAMIC_DEBUG
setting in Config-kernel.in (default N), remove or disable it in target
configs which unconditionally enable it, along with the related setting
CONFIG_DYNAMIC_DEBUG_CORE. This saves several KB in the kernels for
ipq40xx, ipq806x, filogic, mt7622, qoriq, and sunxi.

Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
2023-05-03 10:26:17 -07:00
Daniel Golle
3221128639 mediatek: no longer hard-code WAN PHY of Netgear WAX206
The RealTek 2.5G PHY providing the WAN port of the Netgear WAX206 has
previously been hard-coded in the device tree. Now that the PHY can be
probed correctly also via Clause-45 MDIO, use that instead.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-04-30 17:27:00 +01:00
Hauke Mehrtens
7815c55f7d kernel: Deactivate CONFIG_COMPAT
This deactivates the CONFIG_COMPAT kernel option.
With CONFIG_COMPAT the kernel will provide syscall interfaces for arm32
binaries in addition to the interfaces needed for arm64 binaries.

In OpenWrt the complete userspace is compiled for this specific
architecture and support for 32 bit ARM applications is not needed.
This reduces the size and the attack surface for the systems.

On all other targets CONFIG_COMPAT is already deactivated.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2023-04-29 21:56:53 +02:00
Hauke Mehrtens
ca5555d27e kernel: Activate CONFIG_ARM64_SW_TTBR0_PAN
This activates the CONFIG_ARM64_SW_TTBR0_PAN option for all arm64
kernels by default.

The CONFIG_ARM64_SW_TTBR0_PAN option prevents the kernel form accessing
user space memory directly. This makes it harder to exploit the kernel.

This is activated by default and was already activate on all other arm64
targets before.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2023-04-29 21:56:53 +02:00
Hauke Mehrtens
626b37d70a kernel: Activate CONFIG_HARDENED_USERCOPY for all targets
This activates CONFIG_HARDENED_USERCOPY for the remaining targets. This
adds additional checks in the copy_from_user() and copy_to_user()
functions.

This was not activated for ARCHS38 before because of a bug in the Linux
kernel 5.4 till 5.14, which as fixed and is described here:
https://github.com/foss-for-synopsys-dwc-arc-processors/linux/issues/15

I do not know why this was deactivated for mt7629 and rockchip.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2023-04-29 21:56:53 +02:00
Felix Fietkau
ec6f80663e mediatek: remove mt753x driver
It is unused

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2023-04-29 10:25:43 +02:00
Chukun Pan
21be2c26d5 mediatek: add support for TP-Link TL-XDR4288/608x
Hardware specification:
  SoC: MediaTek MT7986A 4x A53
  Flash: ESMT F50L1G41LB 128MB
  RAM: ESMT M15T4G16256A 512MB
  Ethernet (Max Speed):
    XDR4288: 1x 2.5G Wan, 1x 2.5G Lan, 4x 1G Lan
    XDR6086: 1x 2.5G Wan, 1x 2.5G Lan, 1x 1G Lan
    XDR6088: 1x 2.5G Wan, 1x 2.5G Lan, 4x 1G Lan
  WiFi:
    XDR4288: MT7976DAN (2.4G 2T2R, 5G 3T3R)
    XDR6086/XDR6088:
      WiFi1: MT7976GN 2.4GHz 4T4R
      WiFi2: MT7976AN 5GHz 4T4R
  Button: Reset, WPS, Turbo
  USB: 1 x USB 3.0
  Power: DC 12V 4A

Flash instructions:
  1. Execute the following operation to open nc shell:
     https://openwrt.org/inbox/toh/tp-link/xdr-6086#rooting
  2. Replace the stock bootloader to OpenWrt's:
     dd bs=131072 conv=sync of=/dev/mtdblock9 if=/tmp/xxx-preloader.bin
     dd bs=131072 conv=sync of=/dev/mtdblock9 seek=28 if=/tmp/xxx-bl31-uboot.fip
  3. Connect to your PC via the Gigabit port of the router,
     set a static ip on the ethernet interface of your PC.
     (ip 192.168.1.254, gateway 192.168.1.1)
  4. Download the initramfs image, and restart the router,
     waiting for tftp recovery to complete.
  5. After openwrt boots up, perform sysupgrade.

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
[Add uboot build, fit and sysupgrade support, fix RealTek PHYs]
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-04-22 04:10:19 +01:00
John Audia
3887a55909 kernel: bump 5.15 to 5.15.108
Removed upstreamed:
	backport-5.15/430-v6.3-ubi-Fix-failure-attaching-when-vid_hdr-offset-equals.patch[1]
	backport-5.15/612-v6.3-skbuff-Fix-a-race-between-coalescing-and-releasing-S.patch[2]

All other patches automatically rebased.

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.108&id=85d7a7044b759d865d10395a357632af00de5867
2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.108&id=906a6689bb0191ad2a44131a3377006aa098af59

Build system: x86_64
Build-tested: bcm2711/RPi4B, ramips/tplink_archer-a6-v3, filogic/xiaomi_redmi-router-ax6000-ubootmod
Run-tested: bcm2711/RPi4B, ramips/tplink_archer-a6-v3, filogic/xiaomi_redmi-router-ax6000-ubootmod

Signed-off-by: John Audia <therealgraysky@proton.me>
2023-04-22 01:10:24 +02:00
Chukun Pan
1f68baf5f0
mediatek: filogic: remove redundant code for tuf-ax4200
Remove redundant code in 02_network.

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
2023-04-21 18:44:40 +02:00
Chukun Pan
30d84684cf
mediatek: filogic: move mac address setting together
Simultaneously sort in the order of letters.

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
2023-04-21 18:44:40 +02:00
Chukun Pan
800ce7f7b4
mediatek: filogic: fix network config for mt7986a-rfb
Fix the network configuration according to the device tree.

Fixes: 5faff99 ("mediatek: filogic: fix mt7986a ethernet devicetree entries")
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
2023-04-21 18:44:36 +02:00
Daniel Golle
9f2ede5551 mediatek: filogic: update kernel config-5.15
Expose thermal-zone as hwmon sensor, remove thermal emulation driver
and add some missing symbols.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-04-20 01:05:30 +01:00
Daniel Golle
929634c4de mediatek: bpi-r3: allow up to 3W per SFP module
According to SinoVoip up to 3A @ 3.3V are available for both
SFP modules together. Raise energy limit from 1W (default) to 3W,
however, be aware that using modules consuming more than 1W will
require active cooling!

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-04-20 01:03:56 +01:00
Michał Kępień
fa4dc86e98
kernel: backport MEMREAD ioctl
MEMREAD is a new ioctl for MTD character devices that was first included
in Linux 6.1.  It allows userspace applications to use the Linux
kernel's OOB autoplacement mechanism while reading data from NAND
devices.  The Yafut tool needs this ioctl to do its job.

Signed-off-by: Michał Kępień <openwrt@kempniu.pl>
2023-04-18 13:53:03 +02:00
Daniel Golle
f4f8c0e8de mediatek: sync pinctrl-mt7981 and pinctrl-mt7986 drivers
Now that new pinconf features have been backported sync pinctrl-mt7981
and pinctrl-m7986 with bleeding-edge upstream versions.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-04-13 20:01:33 +01:00
Daniel Golle
3cb2fddd30 mediatek: backport new pinctrl features
Backport new features for MediaTek pinctrl/pinconf drivers from upstream.
This will serve as the base to improve pinconf bias/pull-up/pull-down on
MT7981 and MT7986, and also prepare for upcoming support for MT7988.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-04-13 20:01:33 +01:00
Daniel Golle
e92b153e99 mediatek: introduce KERNEL_LOADADDR to Device/Default template
We need to reset KERNEL_LOADADDR if we use it on a per-device base.
Otherwise the previous value will be kept in case a device doesn't
define KERNEL_LOADADDR and relies on the default.

Move initializing KERNEL_LOADADDR to target/linux/mediatek/image/Makefile,
similar to how it's done also on the ramips target.

This fixes image size related breakage on devices which rely on the
default value of KERNEL_LOADADDR.

While at it use 0x48000000 which is more common than the previous default
0x44000000 for the filogic subtarget.

Fixed: e7c399bee6 ("filogic: add support for ASUS TUF-AX4200")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-04-05 17:12:55 +01:00
David Bauer
f25abdf144 mediatek: make TUF-AX4200 KERNEL simply expanded
The KERNEL variable was recursively expanded, breaking other devices.

Signed-off-by: David Bauer <mail@david-bauer.net>
2023-04-04 02:08:32 +02:00
Andrew Sim
ed2849958f mediatek: re-add wireless driver for TUF-AX4200
The wireless driver package was incorrectly removed from the TUF-AX4200
device-packages, resulting in images without wireless functionality.

Fixes: d98c4fb8bf ("mediatek: broaden filogic target description")

Signed-off-by: Andrew Sim <andrewsimz@gmail.com>
[rework commit description]
Signed-off-by: David Bauer <mail@david-bauer.net>
2023-03-29 17:03:42 +02:00
Felix Fietkau
7472476aef kernel: fix mtk_eth_soc throughput regressions on gigabit PHY ports
Fixes issues on MT7621 and MT7623 switch ports, and PHY ports on all SoC

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2023-03-29 16:14:37 +02:00
Daniel Golle
d98c4fb8bf mediatek: broaden filogic target description
The filogic subtarget now also supports MT7981 and will in future
also support MT7988. Reflect that in the target description.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-03-27 19:07:54 +01:00
Daniel Golle
397c706cba mediatek: add device tree include for the MT7981 SoC
Add mt7981.dtsi so we can start adding MT7981 devices.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-03-27 19:07:54 +01:00
Daniel Golle
5403770105 mediatek: add support for SPI calibration
Newer MediaTek's SoCs need SPI calibration routines for SPI to work
reliably. Import patches for that from MediaTek's SDK.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-03-27 19:07:54 +01:00
Daniel Golle
3542ee9d1f mediatek: add PWM support for MT7981 SoC
Add patch to support PWM on the MT7981 SoC.
This patch will also be submitted to upstream Linux soon.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-03-27 19:07:54 +01:00
Daniel Golle
be6bbd9484 mediatek: add I2C for MT7981 SoC
Add patch to support I2C on the MT7981 SoC.
This change will also be submitted to upstream Linux soon.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-03-27 19:07:54 +01:00
Daniel Golle
ad962c90c3 mediatek: simplify MaxLinear GPY PHY driver
The mxl-gpy driver apparently was built in the assumption that SGMII
auto-negotiation is always switched on at the MAC. This may be true for
few rather recent drivers (why?), but certainly isn't for most drivers
unless 'managed = "in-band-status"' is set in device tree. Add patch to
the mediatek target which reduces mxl-gpy to behave more like an
ordinary PHY driver using out-of-band status.

This allows to use these PHYs without rate-adaptation which seems to be
at least partially broken/racy in some revisions of the PHY and/or
internal PHY firmware.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-03-27 19:07:54 +01:00
Daniel Golle
53dc9a60c0 generic: mtk_eth_soc: switch to external PCS driver
Backport patch to make use of the new PCS driver in mtk_eth_soc.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-03-27 19:07:54 +01:00
Daniel Golle
72094f74a6 generic: net: pcs: add driver for MediaTek SGMII PCS
Backport dedicated PCS driver for MediaTek LynxI SGMII/SerDes unit.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-03-27 19:07:54 +01:00
Daniel Golle
5b972d7272 generic: mtk_eth_soc: allow setting MDIO clock frequency
Backport patch allowing to set the MDIO bus clock frequency.
By default the MDIO bus clock runs on 2.5 MHz, allow increasing it
up to 25 MHz.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-03-27 19:07:54 +01:00
Daniel Golle
a438a805eb mediatek: add support for built-in GE PHYs of newer SoCs
MT7981 and the upcoming MT7988 have built-in Gigabit Ethernet PHYs.
While they share some design properties with the PHYs present in
MT753x, they do need calibration data from the SoC's efuse.

Add driver to support them. Upstreaming it is planned, but there are
still some ongoing discussions with MediaTek.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-03-27 19:07:54 +01:00
Daniel Golle
18a9ae56e9 mediatek: backport pinctrl driver for MT7981 SoC
Backport the pinctrl driver for the MT7981 SoC. The driver has also
been submitted upstream and is part of Linux 6.3.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-03-27 19:07:54 +01:00
Daniel Golle
658c4dd43f mediatek: backport clk driver for MT7981 SoC
Backport driver for common clocks in MT7981 SoC. The driver has also
been submitted upstream and became part of Linux 6.3.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-03-27 19:07:54 +01:00
John Audia
d59d69f9e1 kernel: bump 5.15 to 5.15.103
Manually rebased:
        backport-5.15/704-15-v5.19-net-mtk_eth_soc-move-MAC_MCR-setting-to-mac_finish.patch

Removed upstreamed:
        backport-5.15/060-v6.0-01-tools-build-Add-feature-test-for-init_disassemble_in.patch[1]
        backport-5.15/060-v6.0-02-tools-include-add-dis-asm-compat.h-to-handle-version.patch[2]
        backport-5.15/060-v6.0-03-tools-perf-Fix-compilation-error-with-new-binutils.patch[3]
        backport-5.15/060-v6.0-04-tools-bpf_jit_disasm-Fix-compilation-error-with-new-.patch[4]
        backport-5.15/060-v6.0-05-tools-bpftool-Fix-compilation-error-with-new-binutil.patch[5]
        pending-5.15/733-02-net-ethernet-mtk_eth_soc-fix-RX-data-corruption-issu.patch[6]
        bcm47xx/patches-5.15/170-bgmac-fix-initial-chip-reset-to-support-BCM5358.patch[7]

All other patches automatically rebased.

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.103&id=51b99dc38c1a053e2e732d7f9e2740e343ae7eae
2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.103&id=451c9d7b16169645ed291ebb2ca9844caa088f2d
3. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.103&id=97f005c0bdbaf656a7808586d234965385a06c58
4. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.103&id=1c27fab243333821375e4d63128d60093fdbe149
5. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.103&id=4441a90091931fd81607567961dc122f24f735bb
6. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.103&id=2adc29350a5b4669544566f71f208d2abaec60ab
7. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.103&id=04bfc5bcdfc0fdb73587487c71b04d63807ae15a

Build system: x86_64
Build-tested: bcm2711/RPi4B, ramips/tplink_archer-a6-v3, filogic/xiaomi_redmi-router-ax6000-ubootmod
Run-tested: bcm2711/RPi4B, ramips/tplink_archer-a6-v3, filogic/xiaomi_redmi-router-ax6000-ubootmod

Signed-off-by: John Audia <therealgraysky@proton.me>
2023-03-25 16:01:23 +01:00
David Bauer
e7c399bee6 filogic: add support for ASUS TUF-AX4200
Hardware
--------
SOC:   MediaTek MT7986
RAM:   512MB DDR3
FLASH: 256MB SPI-NAND (Winbond W25N02KV)
WIFI:  Mediatek MT7986 DBDC 802.11ax 2.4/5 GHz
ETH:   MediaTek MT7531 Switch
       MaxLinear GPY211C 2.5 N-Base-T PHY
UART:  3V3 115200 8N1 (Pinout silkscreened / Do not ocnnect VCC)

Installation
------------

1. Download the OpenWrt initramfs image. Copy the image to a TFTP server
   reachable at 192.168.1.66/24. Rename the image to tufax4200.bin.

2. Connect the TFTP server to the AX4200. Conect to the serial console,
   interrupt the autoboot process by pressing '4' when prompted.

3. Download & Boot the OpenWrt initramfs image.

   $ setenv ipaddr 192.168.1.1
   $ setenv serverip 192.168.1.66
   $ tftpboot 0x46000000 tufax4200.bin
   $ bootm 0x46000000

4. Wait for OpenWrt to boot. Transfer the sysupgrade image to the device
   using scp and install using sysupgrade.

   $ sysupgrade -n <path-to-sysupgrade.bin>

Missing features
----------------

 - The LAN port LEDs are driven by the switch but OpenWrt does not
   correctly configure the output.

Signed-off-by: David Bauer <mail@david-bauer.net>
2023-03-24 20:30:29 +01:00
David Bauer
652d5ac152 mediatek: enable bootargs-override for filogic subtarget
The ASUS TUF-AX4200 bootloader adds invalid parameters for the rootfs.
Without overwriting the cmdline, the kernel crashes when trying to
attach the rootfs, as OpenWrt uses a different partition than the vendor
OS.

Signed-off-by: David Bauer <mail@david-bauer.net>
2023-03-24 20:30:29 +01:00
Felix Fietkau
d0a06965e8 mediatek: add kernel code for supporting offloading wlan->eth and wlan->wlan flows
Will be enabled by an upcoming mt76 update

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2023-03-23 17:54:18 +01:00
Felix Fietkau
fbcfb7f7af kernel: update mtk ppe flow accounting patch to the latest version
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2023-03-23 17:54:18 +01:00
Lorenzo Bianconi
e314f7be7e mediatek: filogic: move ilm, dlm and cpu_boot in dedicated nodes
This fixes issues with legacy boot loaders that don't process reserved memory
regions outside of system RAM

Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2023-03-20 21:28:19 +01:00
John Audia
d6d8851d12 kernel: bump 5.15 to 5.15.100
Manually rebased:
        bcm27xx/patches-5.15/950-0421-Support-RPi-DPI-interface-in-mode6-for-18-bit-color.patch
        bcm27xx/patches-5.15/950-0706-media-i2c-imx219-Scale-the-pixel-clock-rate-for-the-.patch
        ramips/patches-5.15/810-uvc-add-iPassion-iP2970-support.patch

Removed upstreamed:
        bcm27xx/patches-5.15/950-0707-drm-vc4-For-DPI-MEDIA_BUS_FMT_RGB565_1X16-is-mode-1-.patch[1]
        bcm27xx/patches-5.15/950-0596-drm-vc4-dpi-Add-option-for-inverting-pixel-clock-and.patch[2]
        ipq807x/0006-v5.16-arm64-dts-qcom-Fix-IPQ8074-PCIe-PHY-nodes.patch [3]
        ipq807x/0034-v6.1-arm64-dts-qcom-ipq8074-fix-PCIe-PHY-serdes-size.patch [4]
        ipq807x/0103-arm64-dts-qcom-ipq8074-fix-Gen2-PCIe-QMP-PHY.patch [5]
        ipq807x/0104-arm64-dts-qcom-ipq8074-fix-Gen3-PCIe-QMP-PHY.patch [6]
        ipq807x/0105-arm64-dts-qcom-ipq8074-correct-Gen2-PCIe-ranges.patch [7]
        ipq807x/0108-arm64-dts-qcom-ipq8074-fix-Gen3-PCIe-node.patch [8]
        ipq807x/0109-arm64-dts-qcom-ipq8074-correct-PCIe-QMP-PHY-output-c.patch [9]
        ipq807x/0132-arm64-dts-qcom-ipq8074-correct-USB3-QMP-PHY-s-clock-.patch [10]

All other patches automatically rebased.

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.99&id=d2991e6b30020e286f2dd9d3b4f43548c547caa6
2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/drivers/gpu/drm/vc4/vc4_dpi.c?h=v5.15.100&id=8e04aaffb6de5f1ae61de7b671c1531172ccf429
3. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/arch/arm64/boot/dts/qcom/ipq8074.dtsi?h=v5.15.99&id=a55a645aa303a3f7ec37db69822d5420657626da
4. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/arch/arm64/boot/dts/qcom/ipq8074.dtsi?h=v5.15.99&id=d9df682bcea57fa25f37bbf17eae56fa05662635
5. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/arch/arm64/boot/dts/qcom/ipq8074.dtsi?h=v5.15.99&id=7e6eeb5fb3aa9e5feffdb6e137dcc06f5f6410e1
6. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/arch/arm64/boot/dts/qcom/ipq8074.dtsi?h=v5.15.99&id=e88204931d9a60634cd50bbc679f045439c4b91d
7.  https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/arch/arm64/boot/dts/qcom/ipq8074.dtsi?h=v5.15.99&id=1563af0f28afd3b6d64ac79a2aecced3969c90bf
8. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/arch/arm64/boot/dts/qcom/ipq8074.dtsi?h=v5.15.99&id=feb8c71f015d416f1afe90e1f62cf51e47376c67
9. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/arch/arm64/boot/dts/qcom/ipq8074.dtsi?h=v5.15.99&id=69c7a270357a7d50ffd3471b14c60250041200e3
10. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/arch/arm64/boot/dts/qcom/ipq8074.dtsi?h=v5.15.99&id=dd3d021ae5471d98adf81f1e897431c8657d0a18

Build system: x86_64
Build-tested: bcm2711/RPi4B, ramips/tplink_archer-a6-v3
Run-tested: bcm2711/RPi4B, ramips/tplink_archer-a6-v3

Signed-off-by: John Audia <therealgraysky@proton.me>
Tested-by: Robert Marko <robimarko@gmail.com> #ipq807x/Dynalink WRX36
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> #ipq807x/ax3600, x86_64/FW-7543B, ath79/tl-wdr3600, ipq806x/g10, ipq806x/nbg6817
2023-03-18 12:52:17 +01:00
Felix Fietkau
9f6d25551e mediatek: add missing DTS entries for WED on MT7986
Needed to support WLAN offloading

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2023-03-05 09:59:00 +01:00
Felix Fietkau
23b46b1c61 linux-firmware: add mt7986 offload firmware
This is needed for WED support on MT7986.
Enable it by default for the filogic subtarget.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2023-03-02 11:25:17 +01:00
Arınç ÜNAL
9df035b3ea treewide: remove label = "cpu" from DSA dt-binding
This is not used by the DSA dt-binding, so remove it from all devicetrees.

Link: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=9cc115d8d6f73dd260de1609182f3645844d6907
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
2023-02-26 22:22:48 +01:00
Marcel Ziswiler
f6d2a23cbc mediatek: add support for Netgear WAX206
Specifications:
* SoC: MediaTek MT7622BV
* RAM: DDR3 512 MiB (Nanya NT5CC256M16ER-EK)
* Flash: SPI-NAND 256 MiB (Toshiba TC58CVG1S3HRAIJ)
* Wi-Fi 2.4/5 GHz 4T4R:
  * 2.4 GHz: MediaTek MT7622BV
  * 5 GHz: MediaTek MT7915AN/MT7975AN
* Ethernet: 4x 10/100/1000 Mbps LAN,
            1x 10/100/1000/2500 Mbps WAN (Realtek RTL8221B PHY)
* Switch: MediaTek MT7531AE
* LEDs/Keys: 8/1 (Power, Internet, LAN1, LAN2, LAN3, LAN4,
             Wifin and Wifia dual-colour LEDs + Reset pin)
* UART: Marked J19 on board VCC GND TX RX, beginning from "1". 3.3v,
        115200n8
* Power: 12 VDC, 2.5 A

Installation:
* Flash the factory image through the stock web interface, or TFTP to
  the bootloader. NMRP can be used to TFTP without opening the case.
* U-Boot allows booting an initramfs image via TFTP as follows:
  setenv ipaddr 192.168.1.1
  setenv serverip 192.168.1.100
  tftpboot openwrt-mediatek-mt7622-netgear_wax206-initramfs-recovery.itb
  bootm

Known Limitations:
* The 2.5G WAN port labeled 'wan' only works for speeds up to 1G at the
  moment. If connected to a multi-gig port the speed has to be manually
  set to 1G/full either for the switch port or in OpenWrt. For example
  add the following to /etc/rc.local to set it on boot:
  /usr/sbin/ethtool -s wan speed 1000 duplex full

Revert to stock firmware:
* Flash the stock firmware to the bootloader using TFTP/NMRP.

References to WAX206 GPL source:
https://www.downloads.netgear.com/files/GPL/WAX206_V1.0.4.0_Source.rar

* openwrt/target/linux/mediatek/dts/mt7622-netgear-wax206.dts
  DTS file for this device.
* openwrt/target/linux/mediatek/image/mt7622.mk
  Image creation code for this device

Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
[fix WAN port (1G only), adjust partition layout, adjust image creation]
Signed-off-by: Thomas Kupper <thomas.kupper@gmail.com>
2023-02-18 15:46:45 +01:00
Daniel Golle
80196f4e3c mediatek: mtk_thermal: replace with upstream patch
Replace local patch adding thermal support for MT7986 with version
accepted upstream.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-02-15 03:28:09 +00:00
Oleg S
b174de2c5f mediatek: mt7622: fix rootfs/ubi detection for Xiaomi AX6S
By specifying the flag "denx,fit" for partition "kernel", the kernel
try to find rootfs in the same partition during boot. Reality is that
the placement of rootfs is precisely determined by the name of another
partition -"ubi".
It was also found that on some device (for example devices with NAND
chips), the "Denx search engine" manages to find roots at the end of
partition "kernel", but such partition doesn't exist and is empty
there.

Fix this by removing the "denx,fit" flag from partition "kernel". With
this change the original behavior of searchif rootfs in partition "ubi"
is restored.

Signed-off-by: Oleg S <remittor@gmail.com>
2023-02-11 21:42:06 +08:00
Felix Baumann
d88e2aa794
mediatek: fix dts whitespace
Replace blanks with tabs

Signed-off-by: Felix Baumann <felix.bau@gmx.de>
2023-02-09 03:03:52 +01:00
Rosen Penev
2630e5063d treewide: replace wpad-basic-wolfssl default
The newly merged mbedtls backend is smaller and has fewer ABI related
issues than the wolfSSL one.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2023-02-04 02:35:03 +01:00
Felix Fietkau
521efb62eb mt76: update to the latest version, import WED related mtk_eth_soc patches
6c256218e59e wifi: mt76: dma: use napi_build_skb
679254c50f27 mt7915: add CONFIG_MT76_LEDS to cflags
15b9dd6b1b6a wifi: mt76: mt7915: call mt7915_mcu_set_thermal_throttling() only after init_work
8e5c21fe7c5c wifi: mt76: mt7915: rework mt7915_mcu_set_thermal_throttling
87cb74fe42d9 wifi: mt76: mt7915: rework mt7915_thermal_temp_store()
c6f24b83eba5 wifi: mt76: mt7915: add error message in mt7915_thermal_set_cur_throttle_state()
99e96b89ee4d wifi: mt76: mt7915: add chip id condition in mt7915_check_eeprom()
833cd420480f wifi: mt76: mt7921: fix channel switch fail in monitor mode
f1f8bae6092d wifi: mt76: mt7921: add ack signal support
f47087a6dd62 wifi: mt76: mt7996: fix chainmask calculation in mt7996_set_antenna()
2f3b0acc1588 wifi: mt76: mt7996: update register for CFEND_RATE
7e9540dcbd70 wifi: mt76: mt7996: do not hardcode vht beamform cap
a37e427d0959 wifi: mt76: connac: fix POWER_CTRL command name typo
98aa346042bd wifi: mt76: mt7915: remove BW160 and BW80+80 support
94fed6a43541 wifi: mt76: mt7921: fix invalid remain_on_channel duration
3c162384d80a wifi: mt76: introduce mt76_queue_is_wed_rx utility routine
a409a9454587 wifi: mt76: mt7915: fix memory leak in mt7915_mcu_exit
8b27ecd3a684 wifi: mt76: mt7996: fix memory leak in mt7996_mcu_exit
683760461dd0 wifi: mt76: dma: free rx_head in mt76_dma_rx_cleanup
0c750cf08f85 wifi: mt76: dma: fix memory leak running mt76_dma_tx_cleanup
5de9ae29bea2 wifi: mt76: mt7915: avoid mcu_restart function pointer
dad96dd3e62d wifi: mt76: mt7603: avoid mcu_restart function pointer
19d36dd9c8ea wifi: mt76: mt7615: avoid mcu_restart function pointer
6fe2c2383d3d wifi: mt76: mt7921: avoid mcu_restart function pointer
9df89143bf71 wifi: mt76: mt7915: get rid of wed rx_buf_ring page_frag_cache
8d51d11760cb wifi: mt76: fix switch default case in mt7996_reverse_frag0_hdr_trans
0d8057dbd51c wifi: mt76: mt7921u: add support for Comfast CF-952AX
ddbf4e933d54 wifi: mt76: mt7915: set sku initial value to zero
06a8904e954e wifi: mt76: mt7915: wed: enable red per-band token drop
724a337caef9 wifi: mt76: mt7915: fix WED TxS reporting
747ca943a5bb wifi: mt76: add flexible polling wait-interval support
133d7859977a wifi: mt76: mt7921: reduce polling time in pmctrl
5fe319a0550e wifi: mt76: add memory barrier to SDIO queue kick
822f060b9d19 wifi: mt76: mt7921: fix rx filter incorrect by drv/fw inconsistent
c6794954a723 wifi: mt76: mt7915: fix memory leak in mt7915_mmio_wed_init_rx_buf
9686cd7cc65c wifi: mt76: switch to page_pool allocator
04da4eaa8235 wifi: mt76: enable page_pool stats
1af4a911ebcb wifi: mt76: mt7915: release rxwi in mt7915_wed_release_rx_buf
e8c10835cf06 wifi: mt76: fix compile error without CONFIG_PAGE_POOL_STATS
0cf0ede7cc42 net: ethernet: mtk_wed: add reset to rx_ring_setup callback
715b3ed9708a net: ethernet: mtk_wed: add reset to tx_ring_setup callback
9107381d0ff3 wifi: mt76: mt7921: fix error code of return in mt7921_acpi_read
36d2a5bf7802 wifi: mt76: mt7996: rely on mt76_connac2_mac_tx_rate_val
c67f57d2cda2 wifi: mt76: dma: add reset to mt76_dma_wed_setup signature
3dace36e2941 wifi: mt76: dma: reset wed queues in mt76_dma_rx_reset
4b229d2da562 wifi: mt76: mt7915: add mt7915 wed reset callbacks
f83958376085 wifi: mt76: mt7915: complete wed reset support
321edbb414dc wifi: mt76: mt7996: rely on mt76_connac_txp_common structure
bdb7dc38a6d1 wifi: mt76: mt7996: rely on mt76_connac_txp_skb_unmap
8688756305c6 wifi: mt76: mt7996: rely on mt76_connac_tx_complete_skb
fbf986dbd4c0 wifi: mt76: mt7996: rely on mt76_connac2_mac_decode_he_radiotap
adc556cbce37 wifi: mt76: mt7996: avoid mcu_restart function pointer
5eb4e2303be4 wifi: mt76: remove __mt76_mcu_restart macro
e7a61c5f70f5 wifi: mt76: add EHT phy type
b375845abc10 wifi: mt76: connac: add CMD_CBW_320MHZ
68b17a243332 wifi: mt76: connac: add helpers for EHT capability
02ec1f61b3a2 wifi: mt76: connac: add cmd id related to EHT support
9209294cd81b wifi: mt76: increase wcid size to 1088
5e85136c9b2f wifi: mt76: add EHT rate stats for ethtool
a171f672fdeb wifi: mt76: mt7996: add variants support
eda8fd62c105 wifi: mt76: mt7996: add helpers for wtbl and interface limit
4a5a9f4cdc3b wifi: mt76: mt7996: rework capability init
06b73c155680 wifi: mt76: mt7996: add EHT capability init
ae71a1b8294f wifi: mt76: mt7996: add support for EHT rate report
65bdfae2991d wifi: mt76: mt7996: enable EHT support in firmware
b2360d59747c wifi: mt76: mt7996: add EHT beamforming support

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2023-02-02 11:16:49 +01:00
Chen Minqiang
016a7bd558 mediatek: fix wrong return code in platform_check_image()
Ensure that the platform_check_image() function returns an error code.

Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
2023-01-29 01:02:45 +00:00
Daniel Golle
ab3c9ccb61
mediatek: filogic: fix sysupgrade on MMC on the BPi-R3
A previous attempt to simplify things went wrong and now sysupgrade
is broken on this device. Fix that.

Fixes: de94587e70 ("mediatek: filogic: don't rely on image preset in flash or sysupgrade")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-01-16 22:04:55 +00:00
Daniel Golle
86a2dae29a
mediatek: mt7622: fix sysupgrade on MMC on BPi-R64
A previous attempt to simplify things went wrong and now sysupgrade
is broken on this device. Fix that.

Fixes: d640cbac0e ("mediatek: mt7622: don't rely on existing image for sysupgrade")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-01-16 22:04:44 +00:00
Shiji Yang
9a07895729 mt76: add stand-alone MT7622 firmware package
Add a separate firmware package to avoid installing the MT7615 firmware
on all MT7622 target devices by default. Now we only add MT7615 firmware
packages for devices that use MT7615E. This commit also removes the
explicit dependency on kmod-mt7615e to refine the package dependency.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2023-01-07 17:11:00 +01:00
Shiji Yang
fc9dd3f083 mt76: add stand-alone MT7915 firmware package
The mt7915e driver supports MT7915, MT7916 and MT7986 chips. And Only
MT7915 series chips need the MT7915 firmware. To save storage, extract
them from the common code package and create a new package to provide
the firmware.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2023-01-07 17:11:00 +01:00
Rafał Miłecki
69ea580882 treewide: update NVMEM symbols
Fixes: 8dfe69cdfc ("kernel: update nvmem subsystem to the latest upstream")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2023-01-07 01:30:31 +01:00
Rafał Miłecki
8dfe69cdfc kernel: update nvmem subsystem to the latest upstream
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2023-01-06 22:08:03 +01:00
Chuanhong Guo
d29dbf052a
mediatek: drop redmi-ax6000 variant with modified env
This variant uses xiaomi factory u-boot and modified u-boot-env &
bootcmd.
By modifying uboot-env, the xiaomi firmware recovery provided in
the vendor u-boot doesn't work anymore. It's possible to put
u-boot into a state where it refuese to take any serial input.
If the u-boot is in this state, users can't restore their
firmware without taking the flash off the board.
We now have a -stock variant where the vendor u-boot is used in
a way that xiaomi firmware recovery still works, and a -ubootmod
variant where we get rid of all xiaomi components, have more
usable space and no uart console lock. These two should cover all
use cases and we don't need this variant anymore.
Drop this redmi-ax6000 variant. Existing users of this variant
should perform a u-boot mod or restore to the -stock layout.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2022-12-30 16:11:59 +08:00
Furong Xu
8bac5dc18a mediatek: add new layout for Xiaomi Redmi Router AX6000 for OpenWrt U-Boot
This new layout is only bootable with OpenWrt U-Boot. It reuses the
two crash partions and expands the ubi partion to the end of whole flash.

Do not use this layout with stock U-Boot!

Signed-off-by: Furong Xu <xfr@outlook.com>
2022-12-29 03:00:31 +00:00
Chuanhong Guo
7fb32285d5
mediatek: redmi-ax6000: drop cs-gpios
'cs-gpios = <0>, <0>' is a hack in ath79 to override the incorrectly
specified maximum number of chipselects available in spi-ath79.c.
It's not needed here and must have been copied here by mistake.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2022-12-17 15:07:54 +08:00
Chen Minqiang
18bea173a6 mediatek: add alternative stock layout for Xiaomi Redmi Router AX6000
In this implementation, the flash partition layout is adjusted to avoid
modifying the uboot environment of mtdparts. This ensures that the 30M
ubi_kernel partition remains aligned with the stock ubi partition, and
the kernel volume is placed in it. This allows the stock uboot to boot
from it without changing the mtdparts, which is useful for reverting back
to the stock firmware using Xiaomi Firmware Tools. In actual testing,
modifying mtdparts has been found to break Xiaomi Firmware Tools.

1. use ARTIFACTS to generate initramfs-factory.ubi for easy installation.
2. The NAND flash layout is changed to allow for reverting back to the
   stock firmware.
3. Before performing sysupgrade, do some cleanup in platform_pre_upgrade
   to ensure a clean installation of OpenWRT.
4. Setup the uboot env to ensure that the system always boot, which can
   be helpful for users who may forget to do this before sysupgrade in
   the initramfs.

New flash instructions:
1. Gain ssh access. Please refer to:
   https://openwrt.org/toh/xiaomi/redmi_ax6000#installation)

2. Check which system current u-boot is loading from:
   COMMAND: `cat /proc/cmdline`
   sample OUTPUT: `console=ttyS0,115200n1 loglevel=8 firmware=1 uart_en=1`
   if firmware=1, current system is ubi1
   if firmware=0, current system is ubi0

3. Setup nvram and write the firmware:
   If the current system is ubi1, please set it up so that the next time
   it will boot from ubi, and write the firmware to ubi:
```
nvram set boot_wait=on
nvram set uart_en=1
nvram set flag_boot_rootfs=0
nvram set flag_last_success=0
nvram set flag_boot_success=1
nvram set flag_try_sys1_failed=0
nvram set flag_try_sys2_failed=0
nvram commit
ubiformat /dev/mtd8 -y -f /tmp/initramfs-factory.ubi
```
   If the current system is ubi, please set it up so that the next time
   it will boot from ubi1, and write the firmware to ubi1:
```
nvram set boot_wait=on
nvram set uart_en=1
nvram set flag_boot_rootfs=1
nvram set flag_last_success=1
nvram set flag_boot_success=1
nvram set flag_try_sys1_failed=0
nvram set flag_try_sys2_failed=0
nvram commit
ubiformat /dev/mtd9 -y -f /tmp/initramfs-factory.ubi
```

4. After rebooting, the system should now boot into the openwrt initramfs.
   Flash the squashfs-sysupgrade.bin via using ssh or luci.
```
sysupgrade -n /tmp/squashfs-sysupgrade.bin
```
Done.

For existing users of the Redmi AX6000 running OpenWrt, here are the steps to
switch to this new layout:

1. Flash initramfs-factory.ubi
```
mtd -r -e ubi write /tmp/initramfs-factory.ubi ubi
```

2. After rebooting, the system will boot into the new openwrt-initramfs.
Log in and perform a sysupgrade to complete the process.
```
sysupgrade -n /tmp/squashfs-sysupgrade.bin
```

Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2022-12-17 15:04:16 +08:00
Furong Xu
d9e1362581 mediatek: add LED support for Xiaomi Redmi AX6000
add DT nodes and default package for the LEDs on Redmi AX6000

Signed-off-by: Furong Xu <xfr@outlook.com>
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2022-12-16 21:42:02 +08:00
Furong Xu
335c1e7cfd mediatek: enable sel_clk for spi-mt65xx
Without explicitly enabling sel_clk, clk_disable_unused() will disable
it when boot is done, causing CPU hang on SPI1 register access on MT7986.
Explicitly enable sel_clk to make SPI1 functional.

Signed-off-by: Furong Xu <xfr@outlook.com>
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2022-12-16 21:42:02 +08:00
John Audia
b6fa423907 kernel: bump 5.15 to 5.15.83
Removed upstreamed:
	backport-5.15/883-v6.1-ca8210-Fix-crash-by-zero-initializing-data.patch[1]

All patches automatically rebased

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.83&id=246bcd05ba6cc43b34ac0bb4bac3ea94a4efa07c

Build system: x86_64
Build-tested: bcm2711/RPi4B
Run-tested: bcm2711/RPi4B

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-12-14 23:34:50 +01:00
Daniel Golle
2307b049e4
mediatek: also move &slot0 from dtsi down to board dts
As the referenced MTD partition is only present in the dts, also move
&slot0 down to the dts files.

Fixes: 64e9b62829 ("mediatek: remove redundant flash entry from dtsi")
Fixes: 7dbac3433f ("mediatek: add support for reyee AX3200-E5")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-12-07 01:45:14 +00:00
Daniel Golle
9d22ab703f mediatek: remove redundant flash entry from dtsi
Splitting-off the common parts of Ruijie RG-EW3200GX PRO and
reyee AX3200-E5 went wrong because the flash descriptiom was kept
also in the dtsi. Remove it there, as flash definition is added by
both board dts files.

Fixes: 7dbac3433f ("mediatek: add support for reyee AX3200-E5")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-12-07 00:46:26 +00:00
Alex Hansen
7dbac3433f mediatek: add support for reyee AX3200-E5
This is yet another model of the Ruijie RG-EW3200GX PRO with a slightly
different flash layout, install process is the same.

Specifications:
SoC: MT7622B
RAM: 256MB
Flash: XMC XM25QH128C or Winbond WQ25Q128JVSQ 16MB SPI NOR
Ethernet: 5x1GbE
Switch: MT7531BE
WiFi: 2.4G: MT7622 5G: MT7915AN+MT7975AN
3LEDs: System LED(blue) + Mesh LED(green) + Mesh LED(red)
2Keys: Mesh button + Reset button
UART: Marked J19 on board. 3.3v, 115200n1
Power: 12V 2.5A

Flash instruction:
1. Serve the initramfs.img using a TFTP server with address 10.10.10.3.
2. Interrupt the uboot startup process via UART.
3. Select "System Load Linux to SDRAM via TFTP" item.
4. (important) Back up firmware(mtd7) partitions with:
    dd if=/dev/mtd7 of=/tmp/firmware.bin
    and then download the firmware.bin image via SCP.
5. Flash the OpenWrt sysupgrade firmware.

Recovery stock firmware:

1. Transfer the firmware.bin image to the device.
2. Flash the image with:
    mtd write firmware.bin firmware

Signed-off-by: Alex Hansen <mralexh123@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-12-06 12:43:15 +00:00
Daniel Golle
83f20fc9f7 mediatek: mt7623: build mt6577_auxadc driver into kernel
Set CONFIG_MT6577_AUXADC=y as otherwise reading temperature of the
thermal-zone doesn't work on MT7623 (it does work fine without this
driver on MT7622 and MT7986).

Fixes: f2ae4e2f8c ("mediatek: clean up platform kernel modules")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-12-05 23:14:36 +00:00
John Audia
590aa0ca51 kernel: bump 5.15 to 5.15.80
Manually rebase:
   pending-5.15/330-MIPS-kexec-Accept-command-line-parameters-from-users.patch
   ath79/patches-5.15/910-unaligned_access_hacks.patch

All other patches automatically rebased

Build system: x86_64
Build-tested: bcm2711/RPi4B
Run-tested: bcm2711/RPi4B

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-11-27 13:18:29 +01:00
Daniel Golle
c1d1202e67
mediatek: set persistent wifi mac for bpi-r64 and bpi-r3
Use persistent MAC address for the built-in wireless interfaces of the
BPi-R64 and BPi-R3 development boards.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-11-24 16:46:33 +00:00
Felix Fietkau
9b482ee22f kernel: add more fixes for mtk_eth_soc
Fix corner cases in DSA offload
Add refcounting fix for flow offload
Fix VLAN untagging issue on MT7986

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-11-21 11:47:36 +01:00
Aleksander Jan Bajkowski
224babfd6f mediatek: mt7623: disable swconfig
The mt7623 subtarget supports 2 devices:
 * Bananapi BPi-R2 (added in 1f068588ef, 7762c07c88),
 * UniElec U7623-02 (added in 4def81f30f).

Both devices support DSA from the beginning, thus
swconfig can be safely disabled.

In the past, the subtarget mt7623 also supported
the mt7623 reference board. This board originally
supported swconfig, and was later converted to DSA
(64175ffb79) and then dropped (1ab81bf02d).

Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
2022-11-18 20:27:52 +01:00
Aleksander Jan Bajkowski
0e001e4185 mediatek: mt7623: refresh config
This was done by executing these command:
$ time make kernel_oldconfig CONFIG_TARGET=subtarget

Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
2022-11-18 20:27:52 +01:00
Felix Fietkau
f753316f4a mediatek: filogic: enable maxlinear PHY support, refresh config
Needed for the 7986 RFB1 board

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-11-09 20:43:55 +01:00
Felix Fietkau
5faff99c7b mediatek: filogic: fix mt7986a ethernet devicetree entries
Add all ports, rename DSA ports to start at lan1

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-11-09 20:43:51 +01:00
Felix Fietkau
4f1e54801e mediatek: drop the use of device tree overlays on mt7986a-rfb board
The boot loader does not support it. Instead make NAND the default image for
this board

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-11-09 20:43:45 +01:00
Felix Fietkau
ceb1451c10 kernel: add mediatek soc ethernet performance improvements
- implement multiqueue via qdma hardware shaper to deal with ports with different speeds
- implement hardware DSA untagging
- add NETIF_F_ALL_TSO to reduce unnecessary segmentation

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-11-09 18:18:27 +01:00
John Audia
1eebe72a80 kernel: bump 5.15 to 5.15.77
Manually rebased:
   bcm27xx/patches-5.15/950-0600-xhci-quirks-add-link-TRB-quirk-for-VL805.patch
   bcm27xx/patches-5.15/950-0606-usb-xhci-add-VLI_TRB_CACHE_BUG-quirk.patch
   bcm27xx/patches-5.15/950-0717-usb-xhci-add-a-quirk-for-Superspeed-bulk-OUT-transfe.patch
   bcm53xx/patches-5.15/180-usb-xhci-add-support-for-performing-fake-doorbell.patch
   lantiq/patches-5.15/0028-NET-lantiq-various-etop-fixes.patch

All other patches automatically rebased

Build system: x86_64
Build-tested: bcm2711/RPi4B, mt7622/RT3200
Run-tested: bcm2711/RPi4B, mt7622/RT3200

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-11-05 16:26:38 +01:00
Nick Hainke
29d987fc89 mediatek: replace mt7986 watchdog assert patch with upstream
Replace "920-watchdog-add-mt7986-assert.patch" with upstreamed
- 920-v5.16-watchdog-mtk-add-disable_wdt_extrst-support.patch
- 921-v5.19-watchdog-mtk_wdt-mt7986-Add-toprgu-reset-controller.patch

Signed-off-by: Nick Hainke <vincent@systemli.org>
2022-11-05 14:07:46 +00:00
Nick Hainke
61a9367b86 mediatek: mt7629: add tag to upstreamed patches
The patches were upstreamed.

Signed-off-by: Nick Hainke <vincent@systemli.org>
2022-11-05 14:07:46 +00:00
Nick Hainke
0c8d84a642 mediatek: add tag for upstreamed patches
The patches were upstreamed.

Signed-off-by: Nick Hainke <vincent@systemli.org>
2022-11-05 14:07:46 +00:00
Nick Hainke
e8080ce89b mediatek: mt7986: add tag to upstreamed patches
The patch "210-pinctrl-mediatek-add-support-for-MT7986-SoC.patch" and
"212-clk-mediatek-add-mt7986-clock-support.patch" are upstreamed.

Signed-off-by: Nick Hainke <vincent@systemli.org>
2022-11-05 14:07:46 +00:00
Nick Hainke
e4270d6493 mediatek: mt7622: add tag to upstreamed patches
The patches "191-arm64-dts-mt7622-specify-the-L2-cache-topology.patch"
and "192-arm64-dts-mt7622-specify-the-number-of-DMA-requests.patch" are
upstreamed to 5.19.

Signed-off-by: Nick Hainke <vincent@systemli.org>
2022-11-05 14:07:46 +00:00
Aleksander Jan Bajkowski
985d59cdf0 mediatek: filogic: disable swconfig
This subtarget supports 3 devices:
 * Bananapi BPi-R3 (added in a96382c1bb),
 * MediaTek MTK7986 rfba AP (added in cffc77ae55),
 * MediaTek MTK7986 rfbb AP (added in cffc77ae55).

This subtarget supports DSA from the beginning. It looks like CONFIG_SWCONFIG
was copied from another config when the subtarget was created.

Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
2022-11-05 14:02:13 +00:00
Aleksander Jan Bajkowski
c4f63f7364 mediatek: filogic: refresh config
This was done by executing these command:
$ time make kernel_oldconfig CONFIG_TARGET=subtarget

Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
2022-11-05 14:02:13 +00:00
Daniel Golle
82a05ce14b
mediatek: remove obsolete patch
The patch enabling hardware flow offloading support on the MT7623 SoC
has been merged upstream as of Linux 5.13. Remove our local patch which
wrongly got forward-ported and now actually enables hardware flow
offloading for the MT2701 SoC family (unsupported in OpenWrt).

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-11-02 11:41:50 +00:00
Daniel Golle
e131a66e30
mediatek: consider adc_oe thermal calibration value in efuse
The use of the adc_oe value stored in the efuse has been dropped in
MediaTek's SDK during a recent refactorization of the temperature
calculation formula. Don't ignore this offset value and again include
it in raw-to-deg-celsius calculation.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-10-31 22:37:05 +00:00
John Audia
a34255b795 kernel: bump 5.15 to 5.15.75
Removed upstreamed:
   bcm27xx/patches-5.15/950-0446-drm-vc4-Fix-timings-for-VEC-modes.patch[1]

Manually rebased:
   patches-5.15/950-0600-xhci-quirks-add-link-TRB-quirk-for-VL805.patch
   bcm27xx/patches-5.15/950-0606-usb-xhci-add-VLI_TRB_CACHE_BUG-quirk.patch
   bcm27xx/patches-5.15/950-0717-usb-xhci-add-a-quirk-for-Superspeed-bulk-OUT-transfe.patch
   bcm53xx/patches-5.15/180-usb-xhci-add-support-for-performing-fake-doorbell.patch

All other patches automatically rebased

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.75&id=2810061452f9b748b096ad023d318690ca519aa3

Build system: x86_64
Build-tested: bcm2711/RPi4B, mt7622/RT3200
Run-tested: bcm2711/RPi4B, mt7622/RT3200

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-10-30 17:54:59 +01:00
Chukun Pan
641e4f2f04 mediatek: add Xiaomi Redmi Router AX6000 support
Hardware specification:
  SoC: MediaTek MT7986A 4x A53
  Flash: ESMT F50L1G41LB 128 MB
  RAM: K4A4G165WF-BCWE 512 MB
  Ethernet: 4x 10/100/1000 Mbps
  WiFi1: MT7976GN 2.4GHz ax 4x4
  WiFi2: MT7976AN 5GHz ax 4x4
  Button: Mesh, Reset

Flash instructions:
  1. Gain ssh and serial port access, see the link below:
     https://openwrt.org/toh/xiaomi/redmi_ax6000#installation
  2. Use ssh or serial port to log in to the router, and
     execute the following command:
     nvram set boot_wait=on
     nvram set flag_boot_rootfs=0
     nvram set flag_boot_success=1
     nvram set flag_last_success=1
     nvram set flag_try_sys1_failed=8
     nvram set flag_try_sys2_failed=8
     nvram commit
  3. Set a static ip on the ethernet interface of your computer
     (e.g. default: ip 192.168.31.100, gateway 192.168.31.1)
  4. Download the initramfs image, rename it to initramfs.bin,
     and host it with the tftp server.
  5. Interrupt U-Boot and run these commands:
     setenv mtdparts nmbm0:1024k(bl2),256k(Nvram),256k(Bdata),2048k(factory),2048k(fip),256k(crash),256k(crash_log),112640k(ubi)
     saveenv
     tftpboot initramfs.bin
     bootm
  6. After openwrt boots up, use scp or luci web
     to upload sysupgrade.bin to upgrade.

Revert to stock firmware:
  Restore mtdparts back to default, then use the
  vendor's recovery tool (Windows only).

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
2022-10-30 14:30:22 +00:00
Aleksander Jan Bajkowski
9226f1e419
kernel: disable CONFIG_CPU_LITTLE_ENDIAN in generic config
Endianness depends on CPU architecture. CONFIG_CPU_(BIG/LITTLE)_ENDIAN should
be enabled on target or subtarget based on SoC architecture.

Fixes warning:
$ make kernel_oldconfig CONFIG_TARGET=subtarget
...
.config:1008:warning: override: CPU_LITTLE_ENDIAN changes choice state
....

Summary:
- ARC - only the CONFIG_CPU_BIG_ENDIAN symbol is defined for this architeture.
  If it is disabled then the processor operates in LITTLE_ENDIAN mode (default),
- ARM32 - CONFIG_CPU_LITTLE_ENDIAN symbol available since kernel 5.19. This
  option should be enabled after OpenWRT moves to kernel 6.x. After refreshing
  the kernel, the symbol disappears,
- ARM64 - enabled CONFIG_CPU_LITTLE_ENDIAN,
- MIPS - enabled relevant symbols,
- POWERPC -  enabled CONFIG_CPU_BIG_ENDIAN,
- UML - Symbols are not defined for this architecture,
- X86 - always little endian. Symbols are not defined for this architecture.

Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
2022-10-21 13:47:01 +02:00
Daniel Golle
c15e7e2910
mediatek: filogic: consolidate adc '32k' clock
Add dependency to '32k' ADC clock so it is always enabled for thermal
and raw access to ADC values. This allows to remove the patch for the
ADC driver and reduce the patch adding thermal support for MT7986 to
only add the new efuse layout and temperature decoding for V3.

Suggested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-10-20 20:37:50 +01:00
John Audia
b1cc4eac1b
mt7622: switch default CPU governor to ondemand
The most common CPU governor in the OpenWRT project is currently ondemand (see
below).  Switch mt7622 over to it as well.

Audit the code by running the following and then analyzing the results:
find -name 'config-5.*' -print0 | xargs -0 grep 'CONFIG_CPU_FREQ_DEFAULT_GOV.*=y'

ondemand: 16
performance: 5
schedutil: 5
userspace: 2

Build system: x86_64
Build-tested: ramips/mt7621

Signed-off-by: John Audia <graysky@archlinux.us>
2022-10-20 00:44:53 +02:00