Hardware specification:
SoC: MediaTek MT7981B 2x A53
Flash: 64GB eMMC or 128 MB SPI-NAND
RAM: 512MB
Ethernet: 4x 10/100/1000 Mbps
Switch: MediaTek MT7531AE
WiFi: MediaTek MT7976C
Button: Reset, Mesh
Power: DC 12V 1A
- UART: 3.3v, 115200n8
--------------------------
| Layout |
| ----------------- |
| 4 | GND TX VCC RX | <= |
| ----------------- |
--------------------------
Gain SSH access:
1. Login into web interface, and download the configuration.
2. Enter fakeroot, decompress the configuration:
tar -zxf cfg_export_config_file.conf
3. Edit 'etc/config/dropbear', set 'enable' to '1'.
4. Edit 'etc/shadow', update (remove) root password:
'root::19523:0:99999:7:::'
5. Repack 'etc' directory:
tar -zcf cfg_export_config_file.conf etc/
* If you find an error about 'etc/wireless/mediatek/DBDC_card0.dat',
just ignore it.
6. Upload new configuration via web interface, now you can SSH to RAX3000M.
Check stroage type:
Check the label on the back of the device:
"CH EC CMIIT ID: xxxx" is eMMC version
"CH CMIIT ID: xxxx" is NAND version
eMMC Flash instructions:
1. SSH to RAX3000M, and backup everything, especially 'factory' part.
('data' partition can be ignored, it's useless.)
2. Write new GPT table:
dd if=openwrt-mediatek-filogic-cmcc_rax3000m-emmc-gpt.bin of=/dev/mmcblk0 bs=512 seek=0 count=34 conv=fsync
3. Erase and write new BL2:
echo 0 > /sys/block/mmcblk0boot0/force_ro
dd if=/dev/zero of=/dev/mmcblk0boot0 bs=512 count=8192 conv=fsync
dd if=openwrt-mediatek-filogic-cmcc_rax3000m-emmc-preloader.bin of=/dev/mmcblk0boot0 bs=512 conv=fsync
4. Erase and write new FIP:
dd if=/dev/zero of=/dev/mmcblk0 bs=512 seek=13312 count=8192 conv=fsync
dd if=openwrt-mediatek-filogic-cmcc_rax3000m-emmc-bl31-uboot.fip of=/dev/mmcblk0 bs=512 seek=13312 conv=fsync
5. Set static IP on your PC:
IP 192.168.1.254, GW 192.168.1.1
6. Serve OpenWrt initramfs image using TFTP server.
7. Cut off the power and re-engage, wait for TFTP recovery to complete.
8. After OpenWrt has booted, perform sysupgrade.
9. Additionally, if you want to have eMMC recovery boot feature:
(Don't worry! You will always have TFTP recovery boot feature.)
dd if=openwrt-mediatek-filogic-cmcc_rax3000m-initramfs-recovery.itb of=/dev/mmcblk0p4 bs=512 conv=fsync
NAND Flash instructions:
1. SSH to RAX3000M, and backup everything, especially 'Factory' part.
2. Erase and write new BL2:
mtd erase BL2
mtd write openwrt-mediatek-filogic-cmcc_rax3000m-nand-preloader.bin BL2
3. Erase and write new FIP:
mtd erase FIP
mtd write openwrt-mediatek-filogic-cmcc_rax3000m-nand-bl31-uboot.fip FIP
4. Set static IP on your PC:
IP 192.168.1.254, GW 192.168.1.1
5. Serve OpenWrt initramfs image using TFTP server.
6. Cut off the power and re-engage, wait for TFTP recovery to complete.
7. After OpenWrt has booted, erase UBI volumes:
ubidetach -p /dev/mtd0
ubiformat -y /dev/mtd0
ubiattach -p /dev/mtd0
8. Create new ubootenv volumes:
ubimkvol /dev/ubi0 -n 0 -N ubootenv -s 128KiB
ubimkvol /dev/ubi0 -n 1 -N ubootenv2 -s 128KiB
9. Additionally, if you want to have NAND recovery boot feature:
(Don't worry! You will always have TFTP recovery boot feature.)
ubimkvol /dev/ubi0 -n 2 -N recovery -s 20MiB
ubiupdatevol /dev/ubi0_2 openwrt-mediatek-filogic-cmcc_rax3000m-initramfs-recovery.itb
10. Perform sysupgrade.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
(cherry picked from commit 423186d7d8)
[rebased to 23.05]
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
The OEM U-Boot uses dual boot and signature verification which does not
support by OpenWrt. So add a custom U-Boot build for OpenWrt.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
(cherry picked from commit fddd735dd5)
Activate the secp521r1 ecliptic curve by default. This curve is allowed
by the CA/Browser forum, see
https://cabforum.org/wp-content/uploads/CA-Browser-Forum-BR-v2.0.1-redlined.pdf#page=110
This increases the size of libmbedtls12_2.28.5-1_aarch64_generic.ipk by
about 400 bytes:
Without:
252,696 libmbedtls12_2.28.5-1_aarch64_generic.ipk
With:
253,088 libmbedtls12_2.28.5-2_aarch64_generic.ipk
Fixes: #13774
Acked-by: Koen Vandeputte <koen.vandeputte@citymesh.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 3c17cdbc36)
Some packages (like wavemon >= 0.9.4) depend on libnl-cli. Add support
for this part of the lib. libnl-cli itself depends on libnl-genl and
libnl-nf. On MIPS, this component adds 81kB.
Signed-off-by: Koen Vandeputte <koen.vandeputte@citymesh.com>
(punctuation correction and reorganisation of commit message)
Signed-off-by: Nick Hainke <vincent@systemli.org>
(cherry picked from commit 4bdd1c1a13)
d8118f6 config: make sure timer is not on the timeouts list before freeing
4bbc6e7 add hostsfile output in addition to statefile
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
(cherry picked from commit 0221b86032)
With patch 101-03-spi-mtk_spim-get-spi-clk-rate-only-once.patch
a new system to calculate the SPI clocks has been added.
Unfortunately, the do_div macro overrides the global
priv->pll_clk_rate field. This will cause to have a reduced
clock rate on each subsequent SPI call.
Signed-off-by: Valerio 'ftp21' Mancini <ftp21@ftp21.eu>
Signed-off-by: Nicolò Veronese <nicveronese@gmail.com>
(cherry picked from commit 8849ccb995)
Upgrading wpa_supplicant from 2.9 to 2.10 breaks broadcom-wl/ath11k
based adapters. The reason for it is hostapd tries to install additional
IEs for scanning while the driver does not support this.
The kernel indicates the maximum number of bytes for additional scan IEs
using the NL80211_ATTR_MAX_SCAN_IE_LEN attribute. Save this value and
only add additional scan IEs in case the driver can accommodate these
additional IEs.
Bug: http://lists.infradead.org/pipermail/hostap/2022-January/040178.html
Bug-Debian: https://bugs.debian.org/1004524
Bug-ArchLinux: https://bugs.archlinux.org/task/73495
Upstream-Status: Changes Requested [https://patchwork.ozlabs.org/project/hostap/patch/20220130192200.10883-1-mail@david-bauer.net]
Reported-by: Étienne Morice <neon.emorice@mail.com>
Tested-by: Étienne Morice <neon.emorice@mail.com>
Signed-off-by: David Bauer <mail@david-bauer.net>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit 6dca88aa4a)
CycloneDX is an open source standard developed by the OWASP foundation.
It supports a wide range of development ecosystems, a comprehensive set
of use cases, and focuses on automation, ease of adoption, and
progressive enhancement of SBOMs (Software Bill Of Materials) throughout
build pipelines.
So lets add support for CycloneDX SBOM for packages and images
manifests.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit d604a07225)
Remove ABI version, since its format is not accepted by the linker.
Enable rpath to avoid clash with system libraries
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 5eb8a21ba5)
It must read the entire image for previous code of 'imsz' or 'imszb'.
Signed-off-by: Jianhui Zhao <zhaojh329@gmail.com>
Suggested-by: Chuanhong Guo <gch981213@gmail.com>
(cherry picked from commit 3bbc1d5fba)
Improve and package builds for various boot media configurations of the
MediaTek MT7981 reference board.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 8428bed15d)
When adding builds for MT7981 the related Makefile sections for MT7986
have apparently been copied, but in one instance the rename from 7986 to
7981 has been omitted. Fix that now.
Fixes: 602cb4f325 ("arm-trusted-firmware-mediatek: add build for MT7981 DDR3")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit be6e257fe6)
The code for hostapd-mbedtls did not work when used for OWE association.
When handling association requests, the buffer offsets and length
assumptions were incorrect, leading to never calculating the y point,
thus denying association.
Also when crafting the association response, the buffer contained the
trailing key-type.
Fix up both issues to adhere to the specification and make
hostapd-mbedtls work with the OWE security type.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 39341f422f)
This fixes building with USE_LTO enabled.
<artificial>:(.text+0xc22): relocation R_MIPS16_26 against `libxt_DNAT_init' cannot be used when making a shared object; recompile with -fPIC
./openwrt/staging_dir/toolchain-mips_24kc_gcc-12.3.0_musl/lib/gcc/mips-openwrt-linux-musl/12.3.0/../../../../mips-openwrt-linux-musl/bin/ld.bfd: non-dynamic relocations refer to dynamic symbol printf
./openwrt/staging_dir/toolchain-mips_24kc_gcc-12.3.0_musl/lib/gcc/mips-openwrt-linux-musl/12.3.0/../../../../mips-openwrt-linux-musl/bin/ld.bfd: failed to set dynamic section sizes: bad value
collect2: error: ld returned 1 exit status
Signed-off-by: Anari Jalakas <anari.jalakas@gmail.com>
(cherry picked from commit 5dbdf3bb3a)
This fixes building with USE_LTO enabled.
<artificial>:(.text+0xcc8): relocation R_MIPS16_26 against `luaL_argerror' cannot be used when making a shared object; recompile with -fPIC
./openwrt/staging_dir/toolchain-mips_24kc_gcc-12.3.0_musl/lib/gcc/mips-openwrt-linux-musl/12.3.0/../../../../mips-openwrt-linux-musl/bin/ld.bfd: non-dynamic relocations refer to dynamic symbol strcpy
./openwrt/staging_dir/toolchain-mips_24kc_gcc-12.3.0_musl/lib/gcc/mips-openwrt-linux-musl/12.3.0/../../../../mips-openwrt-linux-musl/bin/ld.bfd: failed to set dynamic section sizes: bad value
collect2: error: ld returned 1 exit status
Signed-off-by: Anari Jalakas <anari.jalakas@gmail.com>
(cherry picked from commit 246b97b607)
This fixes building with USE_LTO enabled.
<artificial>:(.text+0x4194): relocation R_MIPS16_26 against `cil_printf.lto_priv.0' cannot be used when making a shared object; recompile with -fPIC
./openwrt/staging_dir/toolchain-mips_24kc_gcc-12.3.0_musl/lib/gcc/mips-openwrt-linux-musl/12.3.0/../../../../mips-openwrt-linux-musl/bin/ld.bfd: non-dynamic relocations refer to dynamic symbol memcmp
./openwrt/staging_dir/toolchain-mips_24kc_gcc-12.3.0_musl/lib/gcc/mips-openwrt-linux-musl/12.3.0/../../../../mips-openwrt-linux-musl/bin/ld.bfd: failed to set dynamic section sizes: bad value
collect2: error: ld returned 1 exit status
Signed-off-by: Anari Jalakas <anari.jalakas@gmail.com>
(cherry picked from commit 1925a183a3)
This fixes building with USE_LTO enabled:
<artificial>:(.text.exit+0x6e): relocation R_MIPS16_26 against `pthread_key_delete' cannot be used when making a shared object; recompile with -fPIC
./openwrt/staging_dir/toolchain-mips_24kc_gcc-12.3.0_musl/lib/gcc/mips-openwrt-linux-musl/12.3.0/../../../../mips-openwrt-linux-musl/bin/ld.bfd: non-dynamic relocations refer to dynamic symbol stpcpy
./openwrt/staging_dir/toolchain-mips_24kc_gcc-12.3.0_musl/lib/gcc/mips-openwrt-linux-musl/12.3.0/../../../../mips-openwrt-linux-musl/bin/ld.bfd: failed to set dynamic section sizes: bad value
collect2: error: ld returned 1 exit status
Signed-off-by: Anari Jalakas <anari.jalakas@gmail.com>
(cherry picked from commit 2a33d26d21)
This fixes building with USE_LTO enabled.
<artificial>:(.text+0x400c): relocation R_MIPS16_26 against `iwinfo_close' cannot be used when making a shared object; recompile with -fPIC
./openwrt/staging_dir/toolchain-mips_24kc_gcc-12.3.0_musl/lib/gcc/mips-openwrt-linux-musl/12.3.0/../../../../mips-openwrt-linux-musl/bin/ld.bfd: non-dynamic relocations refer to dynamic symbol strcpy
./openwrt/staging_dir/toolchain-mips_24kc_gcc-12.3.0_musl/lib/gcc/mips-openwrt-linux-musl/12.3.0/../../../../mips-openwrt-linux-musl/bin/ld.bfd: failed to set dynamic section sizes: bad value
collect2: error: ld returned 1 exit status
Signed-off-by: Anari Jalakas <anari.jalakas@gmail.com>
(cherry picked from commit fbacc5ae52)
Currently the zram default compressor choice is displayed whether or not
zram is activated. Since the default choice is lzo-rle, this adds a
false dependency on kmod-lib-lzo.
With this patch, the choice options appear only when activating zram.
Signed-off-by: Rani Hod <rani.hod@gmail.com>
(cherry picked from commit 62ada26de2)
Commit 572ea68070 ("uboot-mediatek: add patches for MT7988 and
builds for RFB") renamed HSGMII to 2500basex, but forgot to update
the dts of Redmi Router AX6000, makes the network unusable.
This patch makes the network usable again.
Fixes: #13724
Fixes: 572ea68070 ("uboot-mediatek: add patches for MT7988 and builds for RFB")
Signed-off-by: Furong Xu <xfr@outlook.com>
(cherry picked from commit 03987d2d11)
479c7f8676d9 cache: make record/hostname lookup case-insensitive
26c97a5a50bf ubus: add a browse flag for suppressing cached ip addresses
c286c51a9bd9 Fix AVL tree traversal in cache_record_find and cache_host_is_known
4035fe42df58 interface: use a global socket instead of per-interface ones
c63d465698c7 cache: dump hostname target from srv records
b42b22152d73 use hostname from SRV record to look up IP addresses
d45c443aa1e6 ubus: add array flag support for the hosts method
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 3e1ac00ccb)
c8c9f10 uim: fix help formatting
aac0776 uqmi: add APN profile commands
ffc5eea uim: support SIM card power-up/down
d6c963d uim: add application state to SIM status
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 0da74dbb45)
Major changes between OpenSSL 3.0.11 and OpenSSL 3.0.12 [24 Oct 2023]
* Mitigate incorrect resize handling for symmetric cipher keys and IVs. (CVE-2023-5363)
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit e4ebc7b566)
1) clear nvram partialboots upon successful boot
This behavior is already defined for EA9500; enabled for EA9200 too.
2) fix MAC address in board.d/02_network
Use the correct nvram variable to derive lan/wan MAC address.
Signed-off-by: Rani Hod <rani.hod@gmail.com>
(cherry picked from commit 9c42d23c5f)
The ucidef_set_network_device_* functions in uci-defaults.sh disagree
on whether to use "network-device" or "network_device" in board.json.
With the additional caveat that jshn will translate hyphens (-) into
underscores (_). This casues problems in netifd which expected
"network_device" causing boards which depend on assigning MACs in
board.json via uci-defaults.sh (or jshn in general) to fail.
This commit addresses the issue by using network_device in
uci-defaults.sh.
The bug was uncovered in the forums here:
https://forum.openwrt.org/t/support-for-rtl838x-based-managed-switches/57875/2596
This was exposed by commit 4ebba8a05d ("realtek: add support for HPE
1920-8g-poe+") where the board_config_load call from 03_gpio introduced
the key normalization by jshn.
Fixes: 9290539ca9 ("base-files: allow setting device and bridge macs")
Tested-by: Stijn Segers <foss@volatilesystems.org>
Signed-off-by: Michael 'ASAP' Weinrich <michael@a5ap.net>
[ improve commit title, description and fix wrong Tested-by tag ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 12bc79d6d5)
Modems which are using qmi do not reply on the 1st sync but they do
on subsequent. So qmi.sh is hanging on the first call. Since 2020 uqmi
supports a timeout parameter. Unfortunately qmi.sh didn't make use of
this parameter. So qmi.sh is now invoking an early dummy access to
unlock the modem
Signed-off-by: Uwe Niethammer <uwe@dr-niethammer.de>
(cherry picked from commit 32a696f9e4)
Add missing PKG_MIRROR_HASH. This is always needed as is used to
generate and use a tar instead of git clone and validate the hash of it.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit a181b9f0f9)
Recent hostapd changes just edited the ucode files. It is required to
bump the PKG_RELEASE to include the newest changes in the latest builds.
Signed-off-by: Nick Hainke <vincent@systemli.org>
(cherry picked from commit 91d2ead3c3)
If the full interface is restarted while bringing up an AP, it can trigger a
wpa_supplicant interface start before wpa_supplicant is notified of the
allocated mac addresses.
Fix this by moving the iface_update_supplicant_macaddr call to just after
the point where mac addresses are allocated.
Reported-by: Michael-cy Lee (李峻宇) <Michael-cy.Lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit abceef120d)
The PKG_CPE_ID links to NIST CPE version 2.2.
Assign PKG_CPE_ID to all remaining package which have a CPE ID.
Not every package has CPE id.
Related: https://github.com/openwrt/packages/issues/8534
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Ensure that the iface disable in uc_hostapd_iface_start also clears the ACS
state.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit f1bb528ae7)
Changes between 3.0.10 and 3.0.11 [19 Sep 2023]
* Fix POLY1305 MAC implementation corrupting XMM registers on Windows. ([CVE-2023-4807])
Signed-off-by: Ivan Pavlov <AuthorReflex@gmail.com>
(cherry picked from commit bfd54529fa)
This is needed for ksh/bash style process substitution such as
<(command) and >(command) which was introduced in ash as of busybox
version 1.34.0 to work.
Signed-off-by: Erik Karlsson <erik.karlsson@genexis.eu>
(cherry picked from commit fdce970dbb)
Changes:
9dc0800 wireless-regdb: Update regulatory rules for Philippines (PH)
111ba89 wireless-regdb: Update regulatory rules for Egypt (EG) from March 2022 guidelines
ae1421f wireless-regdb: Update regulatory info for Türkiye (TR)
20e5b73 wireless-regdb: Update regulatory rules for Australia (AU) for June 2023
991b1ef wireless-regdb: update regulatory database based on preceding changes
Signed-off-by: Yuu Toriyama <PascalCoffeeLake@gmail.com>
(cherry picked from commit 0e13363de6)
The ZTE MF287 requires a different board calibration file for ath10k than
the ZTE MF287+. The two devices receive their own DTS, thus the device tree
is slightly refactored.
Signed-off-by: Andreas Böhler <dev@aboehler.at>
(cherry picked from commit 9c7578d560)
The patch refresh accidentally moved the hostapd_ucode_free_iface call to
the wrong function
Fixes: e9722aef9e ("hostapd: fix a crash when disabling an interface during channel list update")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 3a5ad6e3d7)
Some users have their routers configured to supply a DHCP range that
includes the local interface address.
That worked with dnsmasq because it automatically skips the local
address.
Re-enable those existing configurations for the release and hint at
possible future problems.
Signed-off-by: Leon M. Busch-George <leon@georgemail.eu>
[ wrap commit description and remove unecessary text ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Allow grace period for DFS available after shutting down beacons on the channel
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 16889141d9)
Without it, a lot of authentication modes fail without obvious error messages
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 560965d582)
db3934d2f740 scripts/netifd-wireless.sh: properly fix WPA3 Enterprise support
Support the following values for the different WPA3 Enterprise modes:
- wpa3-mixed: WPA3 Enterprise transitional mode
This supports EAP with both SHA1 and SHA-256, with optional MFP
- wpa3: WPA3 Enterprise only mode
This supports only SHA256 with mandatory MFP
- wpa3-192: WPA3 Enterprise with mandatory 192 bit support
This uses only GCMP-256 ciphers
Disable 192 bit support and GCMP-256 ciphers for the regular "wpa3" mode.
It seems that even leaving in optional 192 bit support breaks auth on some
clients, including iOS devices.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 8c03dc962f)
WPA3 Enterprise-transitional requires optional MFP support and SHA1+SHA256
WPA3 Enterprise-only requires SHA1 support disabled and mandatory MFP.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit b63df6ce5d)
Use the SHA384 variant to account for longer keys with more security
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit f0d1349b52)
077e05f2b129 vlan/vlandev: pass through extra vlan information passed via hotplug
40fad91eb5be wireless: add network_vlan config attribute
1571e18e4a69 bridge: add support for configuring extra tagged vlans on member devices
b719f189f243 bridge: make hotplug-added vlans default to tagged
edf3aced9f9a bridge: add support for adding vlan ranges via hotplug
493e1589bc8b bridge: fix coverity false positive report
03a619947717 bridge: add support for configuring extra vlans for the bridge itself
4bea6d21a9ab wireless: fix changing reconf/serialize options in configuration
255b4d5c472e wireless: fix handling config reload with reconf=1
1ab992a74b43 wireless: fix another reconf issue
e94f7a81a039 bridge: fix config reload on 32 bit systems
8c2758b4fbbb wireless: add support for replacing data blobs at runtime
0ff22a6a68ce wireless: enable dynamic reconfiguration by default
4711f74479e2 netifd: fix disabling radio via config if reconf is being used
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 09fd59938b)
This significantly improves config reload behavior and also fixes some
corner cases related to running AP + mesh interfaces at the same time.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Arm platforms with the right hardware blocks (such as
GICv3.0+ interrupt controller and SMMU/IOMMU) are
able to use vfio-pci to pass through PCI devices
to a VM.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
(cherry picked from commit 9ac01aac0a)
The vfio module only exposes the enable_unsafe_noiommu_mode parameter
if CONFIG_VFIO_NOIOMMU is enabled. When it isn't, the module
will complain about an unknown parameter:
vfio: unknown parameter 'enable_unsafe_noiommu_mode' ignored
As CONFIG_VFIO_NOIOMMU is disabled by the module package,
we can remove the module loading parameter.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
(cherry picked from commit 7ad8612a23)
vhost-net is used to accelerate traffic to virtualisation
guests that use the virtio-net network card in QEMU.
Generally it is invoked by specifying "vhost=on" to a
QEMU -netdev device:
qemu-system-aarch64 -nographic -M virt -cpu host \
--enable-kvm -bios u-boot.bin -smp 1 -m 2048 \
-drive file=openwrt-armsr-armv8.img,format=raw,index=0,media=disk \
-device "virtio-net,netdev=landev,disable-legacy=off,disable-modern=off" \
-netdev "tap,id=landev,helper=/usr/lib/qemu-bridge-helper --br=br-lan,vhost=on"
Signed-off-by: Mathew McBride <matt@traverse.com.au>
(cherry picked from commit d188db8aed)
Add 2 seconds sleep after each forcibly killed/tried-to-kill process
in the final process termination loop in sysupgrade stage2.
This is needed especially for qualcommax/ipq807x, where ath11k
wireless driver may have a long 10-20 seconds delay after termination
before actually getting killed. This often breaks sysupgrade.
The current KILL loop in kill_remaining does all 10 kill attempts
consecutively without any delay, as evidenced here in a failing sysupgrade.
It does not allow any time for the process to finalize its internal
termination.
Sat Sep 2 19:05:56 EEST 2023 upgrade: Sending TERM to remaining processes ...
Sat Sep 2 19:05:56 EEST 2023 upgrade: Sending signal TERM to hostapd (2122)
Sat Sep 2 19:05:56 EEST 2023 upgrade: Sending signal TERM to hostapd (2138)
Sat Sep 2 19:06:00 EEST 2023 upgrade: Sending KILL to remaining processes ...
Sat Sep 2 19:06:00 EEST 2023 upgrade: Sending signal KILL to hostapd (2122)
Sat Sep 2 19:06:00 EEST 2023 upgrade: Sending signal KILL to hostapd (2138)
Sat Sep 2 19:06:00 EEST 2023 upgrade: Sending signal KILL to hostapd (2138)
Sat Sep 2 19:06:00 EEST 2023 upgrade: Sending signal KILL to hostapd (2138)
Sat Sep 2 19:06:00 EEST 2023 upgrade: Sending signal KILL to hostapd (2138)
Sat Sep 2 19:06:00 EEST 2023 upgrade: Sending signal KILL to hostapd (2138)
Sat Sep 2 19:06:00 EEST 2023 upgrade: Sending signal KILL to hostapd (2138)
Sat Sep 2 19:06:00 EEST 2023 upgrade: Sending signal KILL to hostapd (2138)
Sat Sep 2 19:06:00 EEST 2023 upgrade: Sending signal KILL to hostapd (2138)
Sat Sep 2 19:06:00 EEST 2023 upgrade: Sending signal KILL to hostapd (2138)
Sat Sep 2 19:06:00 EEST 2023 upgrade: Sending signal KILL to hostapd (2138)
Sat Sep 2 19:06:00 EEST 2023 upgrade: Failed to kill all processes.
sysupgrade aborted with return code: 256
The change in this commit adds a 2 seconds delay after each kill attempt
in order to allow some processes to more gracefully handle their
internal termination.
The result is like this:
Sun Sep 3 11:15:10 EEST 2023 upgrade: Sending TERM to remaining processes ...
Sun Sep 3 11:15:10 EEST 2023 upgrade: Sending signal TERM to hostapd (2309)
Sun Sep 3 11:15:10 EEST 2023 upgrade: Sending signal TERM to hostapd (2324)
Sun Sep 3 11:15:14 EEST 2023 upgrade: Sending KILL to remaining processes ...
Sun Sep 3 11:15:14 EEST 2023 upgrade: Sending signal KILL to hostapd (2309)
[ 699.827521] br-lan: port 7(hn5wpa2r) entered disabled state
[ 699.908673] device hn5wpa2r left promiscuous mode
[ 699.908721] br-lan: port 7(hn5wpa2r) entered disabled state
[ 701.038029] br-lan: port 6(hn5wpa3) entered disabled state
Sun Sep 3 11:15:16 EEST 2023 upgrade: Sending signal KILL to hostapd (2324)
[ 702.058256] br-lan: port 5(hn2wlan) entered disabled state
[ 709.250063] stage2 (8237): drop_caches: 3
Sun Sep 3 11:15:25 EEST 2023 upgrade: Switching to ramdisk...
The delay introduced here only kicks in if there is some process that
does not get terminated by the first TERM call. Then there is at least
one 2 sec wait after the first KILL loop round.
This commit is related to discussion in PRs #12235 and #12632
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Reviewed-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 47d56ae546)
With recent updates of TF-A the previously already fixed bug slipped
back into the source tree. Again, reorder bl2 init for MT7622 and
initialize WDT only after DRAM init has completed to avoid the
notorious hang.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 948ad2ec7a)
Sync SPI-NAND/ECC controller driver for MT7622, MT7981, MT7986 and MT7988:
* Platform data for MT7981 was actually missing and is now added.
* Add support for Winbond W25N01KV 1Gbit chip.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 9725524235)
During the channel scanning process, the driver will continuously
switch channels. It seems that the full RF calibration step in
rt2800_config_channel() caused the channel scanning function to
timeout. To fix it, move the RF calibration to rt2800_enable_radio()
so that it is only executed once. This commit also includes some
coding format adjustments to follow the Linux recommended style.
Fixes: 2824fa6963 ("mac80211: rework MT7620 PA/LNA RF calibration")
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
(cherry picked from commit ce6ad123e7)
This patch makes some improvements to the MT7620 RF calibration.
1. Move MT7620 PA/LNA calibration code to dedicated functions.
2. Restore RF and BBP registers before R-Calibration.
3. Do Rx DCOC calibration again before RXIQ calibration.
4. Use SoC specific AGC initial LNA value.
5. Correct MAC_RX_EN mask in rt2800_r_calibration()[1].
[1] This change may fix the "BBP/RF register access failed" error:
ieee80211 phy0: rt2800_wait_bbp_rf_ready: Error - BBP/RF register access failed, aborting
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
(cherry picked from commit 2824fa6963)
Always enable built-in 2.5G PHY on MT7988 for now, so that it can be
used. In future it would be nice to be able to switch power and MDIO
access via address 0 at run-time in Linux, both, to be able to use
external PHYs at address 0 and to reduce power consumption on systems
not using the built-in 2.5G PHY.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 33046d2a47)
The U-Boot build for the MT7988 reference board booting from SD card
wrongly depended on the 'ddr4' variant of the ARM TrustedFirmware-A build
even though the 'comb' variant is used. Fix that dependency.
Fixes: 572ea68070 ("uboot-mediatek: add patches for MT7988 and builds for RFB")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 78e3adcaf9)
While the v2 is nearly identical to v1, v3 uses a different PHY and
needs a different build for Ethernet to work in U-Boot.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit fff4441135)
Select many potentially useful options for the MT7988 RFB U-Boot builds.
The resulting loader is intended as a development tool and intends to be
generic. It does *not* have a default bootcmd set, but allows to boot
pretty much everything, including EFI executables.
To install this U-Boot build to the eMMC:
opkg install mmc-utils partx-utils
mmc bootpart enable 1 1 /dev/mmcblk0
echo 0 > /sys/block/mmcblk0boot0/force_ro
dd if=*mediatek_mt7988a-rfb-nand-emmc-preloader.bin of=/dev/mmcblk0boot0
dd if=*mediatek_mt7988a-rfb-nand-emmc-gpt.bin of=/dev/mmcblk0
partx -a /dev/mmcblk0
dd if=*mediatek_mt7988a-rfb-nand-emmc-bl31-uboot.fip of=/dev/mmcblk0p3
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 1d5778e18d)
7aefb47 jitterentropy-rngd: update to the v1.2.0
What's interesting about jitterentropy-rngd v1.2.0 release is that it
bumps its copy of jitterentropy-library from v2.2.0 to the v3.0.0. That
bump includes a relevant commit 3130cd9 ("replace LSFR with SHA-3 256").
When initializing entropy jent calculates time delta. Time values are
obtained using clock_gettime() + CLOCK_REALTIME. There is no guarantee
from CLOCK_REALTIME of unique values and slow devices often return
duplicated ones.
A switch from jent_lfsr_time() to jent_hash_time() resulted in many less
cases of zero delta and avoids ECOARSETIME.
Long story short: on some system this fixes:
[ 6.722725] urngd: jent-rng init failed, err: 2
This is important change for BCM53573 which doesn't include hwrng and
seems to have arch_timer running at 36,8 Hz.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit c74b5e09e6)
This reverts commit 23953cfa5a.
01837 seems to be having multiple issues, one being broken multicast so
lets revert to the last version that was better for the stable branch.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Fix compatible string to match what is supported upstream, fix alignment
and order MTD partitions according to offset.
Signed-off-by: Stefan Agner <stefan@agner.ch>
(cherry picked from commit 4af06aaf33)
Commit e978072baaca ("Do prune_association only after the STA is
authorized") causes issues when an STA roams from one interface to
another interface on the same PHY. The mt7915 driver is not able to
handle this properly. While the commits fixes a DoS, there are other
devices and drivers with the same limitation, so revert to the orginal
behavior for now, until we have a better solution in place.
Fixes: #13156
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
(cherry picked from commit 324673914d)
Support for PF_XDP sockets monitoring interface used by the ss tool.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
(cherry picked from commit 06e64f9b36)
Add u-boot env config for Xiaomi mi-mini for using fw_printenv and fw_setenv on this board
Signed-off-by: Ivan Pavlov <AuthorReflex@gmail.com>
(cherry picked from commit a87bc138cf)
This updates the Intel iwlwifi firmware for AX200 and AX210 from version
66 to version 72. Version 72 is the latest version supported by iwlwifi
from kernel 6.1.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 00ce1c0587)
Instead of reading only a single 4kiB page, read the first 128kiB to
determine the size of an uImage.FIT using 'imsz' or 'imszb'.
This will be needed once we add more Device Tree Overlays, which may
happen for the BPi-R3 mini.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 3c2f7bb555)
Add support for the SKBPRIO queuing discipline. This is subtly
different than prio as it also drops packets from the lower priority
flows.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
(cherry picked from commit 8fba9afda5)
colrm is already built, package just isn't generated.
colrm can be used to remove columns from file/stdin.
Use cases vary, personally I needed it because I build openwrt
natively - and wolfssl configure script wants either colrm, or cut
but busybox's cut isn't accepted.
Built: x86_64, latest git
Tested: x86_64, latest git
Signed-off-by: Oskari Rauta <oskari.rauta@gmail.com>
(cherry picked from commit e21b4c9636)
Safely detect integer overflow in try_addint() and try_subint().
Old code relied on undefined behavior, and recent versions of GCC on x86
optimized away the if-statements.
This caused integer overflow in Lua code instead of falling back to
floating-point numbers.
Signed-off-by: Adam Bailey <aebailey@gmail.com>
(cherry picked from commit 3a2e7c30d3)
commit c0611b45a9 ("e2fsprogs: symlink e2fsck to fsck.ext{2, 3, 4},
and tune2fs to findfs") introduced a symlink from tune2fs to findfs.
This only works when the included private libblkid library is used, but
commit 5b1660a538 ("utils/e2fsprogs: Update to 1.43.6") disabled the
usage of this private lib and enabled the shared lib support.
Removing this symlink makes it possible to install tune2fs and findfs
package.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
(cherry picked from commit 0b80c5725f)
d1f07cf devices: add device id for Atheros AR9287 and AR9380
65ea345 nl80211: constify a few arrays
ca79f64 lib: report byte counters as 64 bit values
This contains an ABI change, increase the ABI version too.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit a226153067)
Changes between 3.0.9 and 3.0.10 [1 Aug 2023]
* Fix excessive time spent checking DH q parameter value ([CVE-2023-3817])
* Fix DH_check() excessive time with over sized modulus ([CVE-2023-3446])
* Do not ignore empty associated data entries with AES-SIV ([CVE-2023-2975])
Signed-off-by: Ivan Pavlov <AuthorReflex@gmail.com>
(cherry picked from commit 92602f823a)
Package kernel module for Marvell 10G Ethernet PHYs found also in many
10G/1G/100M/10M RJ-45 SFP+ modules.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 2a5c7bf621)
Add patch to fix build failure caused by a missing header which had
previously been implicitely included.
Fixes: 6ddb5f5a65 ("uboot-mediatek: update to version 2023.07.02")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Among the patches adding support for MT7988 also came the switch to
use fdtdec_setup_mem_size_base() and no longer rely on CFG_SYS_SDRAM_BASE.
Take care of our downstream boards which did not have a 'memory' node in
their device trees.
Fixes: 572ea68070 ("uboot-mediatek: add patches for MT7988 and builds for RFB")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Import pending patches adding support for MT7988 and provide builds
for the reference board for all possible boot media.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Release 2023.07 got tagged wrongly and replaced by follow-up release
2023.07.02.
Now using upstream DTS for BPi-R3.
Removed two patches which made it upstream, refreshed the rest.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Instead of using the hash of the Github-generated tarball use the
hash of the tarball generated by the OpenWrt build system (in this
case they are different, unfortunately).
Reported-by: Chen Minqiang <ptpt52@gmail.com>
Fixes: 07dbeb430e ("arm-trusted-firmware-mediatek: update to sources of 2023-07-24")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Use updated Trusted Firmware-A sources from MediaTek, now stacked
on top of the ARM Trusted Firmware-A v2.9 release.
Add builds for the newly added MT7988 SoC.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Because this device enable NMBM by default, most users use custom
U-Boot with NMBM-Enabled in Chinese forums.
This layout is the same as the ubootmod layout but enabling NMBM.
Signed-off-by: Hank Moretti <mchank9999@gmail.com>
Since 2021.07 multiple bugs were introduced that made it impossible to
create a bootable target for mvebu. Those issues should be now fixed since
2023.07-rc1.
References: #11661
Signed-off-by: Oli Ze <olze@trustserv.de>
Reviewed-by: Robert Marko <robimarko@gmail.com>
Tested-by: Andre Heider <a.heider@gmail.com> # espressobin-v3-v5-1gb-2cs
Signed-off-by: Petr Štetiar <ynezz@true.cz> [facelift]
(cherry picked from commit ba7d6dddc7)
8667347 build: allow passing SOVERSION value for dynamic library
Also adjust packaging of the library to only ship the SOVERSION
suffixed library object, to allow for concurrent installation of
ABI-incompible versions in the future.
Fixes: #13082
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
(cherry picked from commit 4af0a72a65)
At least Fedora and RHEL 9 set RSAMinSize=2048, so when trying to use
failsafe, we get 'Bad server host key: Invalid key length'
To workaround the issue, we can use: ssh -o RSAMinSize=1024 ...
Generating 2048 bits RSA is extremely slow, so add ed25519.
We keep RSA 1024 to be as compatible as possible.
Signed-off-by: Etienne Champetier <champetier.etienne@gmail.com>
(cherry picked from commit 6ac61dead9)
Changelog from quic:
Bug fixes, stability improvements from previous releases
are present. There are no backward comatibility issues
with this release.
Tested-by: Michał Kwiatek <michal@kwiatek.it> # Xiaomi AX3600
Signed-off-by: Michał Kwiatek <michal@kwiatek.it>
[ improve commit description ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 1c56801dd2)
The Traverse LS1043 boards were not publicly released,
all the production has been going to OEM customers who
do not use the image format defined in the OpenWrt tree.
Only a few samples were circulated outside Traverse
and our OEM customers. The public release (then called
Five64) of this series was cancelled in favour of our
LS1088A based design (Ten64).
It is best to remove these boards to avoid wasting
OpenWrt project and contributor resources.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
(cherry picked from commit 8e7ba6fbae)
The Ten64 board[1] is based around NXP's Layerscape LS1088A SoC.
It is capable of booting both standard Linux distributions
from disk devices, using EFI, and booting OpenWrt
from NAND.
See the online manual for more information, including the
flash layout[2].
This patchset adds support for generating Ten64 images
for NAND boot.
For disk boot, one can use the EFI support that was
recently added to the armvirt target.
We previously supported NAND users by building
inside our armvirt/EFI target[3], but this approach
is not suitable for OpenWrt upstream. Users who
used our supplied NAND images will be able to upgrade
to this via sysupgrade.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
[1] - https://www.traverse.com.au/hardware/ten64
[2] - https://ten64doc.traverse.com.au/hardware/flash/
[3] - Example:
285e4360e1
(cherry picked from commit af0546da34)
If dual-stack configuration is in use, and dhcpv6 option is set, do not start
464xlat sub-interface for dhcpv6 sub-interace , as the configuration already
provides IPv4 connectivty, be it through single or dual APN configuration.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
(cherry picked from commit a9237c1af9)
Add two new "v6apn" and "v6profile" properties, to support split-APN
dual-stack onfiguration. This extends the existing ipv4v6 PDP type,
allowing simultaneous connection to two distinct APNs,
one for IPv4 and one for IPv6.
The parameters override existing 'apn' and 'profile' respectively,
if set, but only for IPv6 part of the connection.
If unset, they default to their original values, constituting a standard
IPv4v6 setup.
If a different APN is set for IPv6, a corresponding profile MUST also be
configured, with a different ID, than the IPv4 profile, for example,
profile 2.
Both APNs must match ones configured through QMI or through 'AT+CGDCONT'
command.
Example configuration in UCI:
config interface 'wan'
option proto 'qmi'
option device '/dev/cdc-wdm0'
option autoconnect '1'
option pdptype 'ipv4v6'
option apn 'internet'
option v6apn 'internetipv6'
option profile '1'
option v6profile '2'
Corresponding profile configuration:
AT+CGDCONT?
+CGDCONT: 1,"IP","internet","0.0.0.0",0,0,0,0
+CGDCONT: 2,"IPV6","internetipv6","0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0",0,0,0,0
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
(cherry picked from commit 48e8bf1b8f)
This patch will only force mac80211 loss detection upon ath10k by
masking the driver-specific loss-detection bit.
Ref: commit ed816f6ba8 ("mac80211: always use mac80211 loss detection")
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit d9070f8d23)
[felix.bau@gmx.de: replace path 6.2 with 5.15, refresh patches]
Signed-off-by: Felix Baumann <felix.bau@gmx.de>
53edfc7aaa34 wifi: mt76: mt7603: fix beacon interval after disabling a single vif
7ef4dd12d982 wifi: mt76: mt7603: fix tx filter/flush function
152608a40aa7 wifi: mt76: mt7615: do not advertise 5 GHz on first phy of MT7615D (DBDC)
cacac3902a63 wifi: mt76: split get_of_eeprom in subfunction
cd3dfe392769 wifi: mt76: add support for providing eeprom in nvmem cells
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 4395236a10)
Hardware
--------
CPU: Mediatek MT7981
RAM: 512M DDR4
FLASH: 256M NAND
ETH: MaxLinear GPY211 (2.5GbE N Base-T)
WiFi: Mediatek MT7981 (2.4GHz 2T2R:2 5GHz 3T3R:2 802.11ax)
BTN: 1x Reset
LED: 1x Multi-Color
UART Console
------------
Available below the rubber cover next to the ethernet port.
Settings: 115200 8N1
Layout:
<12V> <LAN> GND-RX-TX-VCC
Logic-Level is 3V3. Don't connect VCC to your UART adapter!
Installation Web-UI
-------------------
Upload the Factory image using the devices Web-Interface.
As the device uses a dual-image partition layout, OpenWrt can only
installed on Slot A. This requires the current active image prior
flashing the device to be on Slot B.
In case this is not the case, OpenWrt will boot only one time, returning
to the ZyXEL firmware the second boot.
If this happens, first install a ZyXEL firmware upgrade of any version
and install OpenWrt after that.
Installation TFTP / Recovery
----------------------------
This installation routine is especially useful in case of a bricked
device.
Attach to the UART console header of the device. Interrupt the boot
procedure by pressing Enter.
The bootloader has a reduced command-set available from CLI, but more
commands can be executed by abusing the atns command.
Boot a OpenWrt initramfs image available on a TFTP server at
192.168.1.66. Rename the image to nwa50axpro-openwrt-initramfs.bin.
$ atnf nwa50axpro-openwrt-initramfs.bin
$ atna 192.168.1.88
$ atns "192.168.1.66; tftpboot; setenv fdt_high 0xffffffffffffffff;
bootm"
Upon booting, set the booted image to the correct slot:
$ zyxel-bootconfig /dev/mtd9 get-status
$ zyxel-bootconfig /dev/mtd9 set-image-status 0 valid
$ zyxel-bootconfig /dev/mtd9 set-active-image 0
Copy the OpenWrt sysupgrade image to the device using scp.
Write the sysupgrade image to NAND using sysupgrade.
$ sysupgrade -n image.bin
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit f0445746f6)
The side-effect and main motivation is to also drop the FIT structure size
limit because with multiple device tree overlays it may easily grow beyond
the previous 4kB limit in the future.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 98e3f82c3f)
The OEM uboot limit brush into 3rd-party firmware.
So add a custom uboot build to support openwrt.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
(cherry picked from commit 437e79ad6d)
Netgear EX6250v2, EX6400v3, EX6410v2, EX6470 are wall-plug 802.11ac
(Wi-Fi 5) extenders. Like other MT7629 devices, Wi-Fi does not work
currently as there is no driver.
Related: https://github.com/openwrt/openwrt/pull/5084
For future reference, 2.4GHz MAC = LAN+1, 5GHz MAC = LAN+2.
Specifications:
* MT7629, 256 MiB RAM, 16 MiB SPI NOR
* MT7761N (2.4GHz) / MT7762N (5GHz) - no driver
* Ethernet: 1 port 10/100/1000
* UART: 115200 baud (labeled on board)
Installation:
* Flash the factory image through the stock web interface, or TFTP to
the bootloader. NMRP can be used to TFTP without opening the case.
* After installation, perform a factory reset. Wait for the device to
boot, then hold the reset button for 10 seconds. This is needed
because sysupgrade in the stock firmware will attempt to preserve its
configuration using sysupgrade.tgz.
See https://github.com/openwrt/openwrt/pull/4182
Revert to stock firmware:
* Flash the stock firmware to the bootloader using TFTP/NMRP.
Signed-off-by: Wenli Looi <wlooi@ucalgary.ca>
(cherry picked from commit 73de41898f)
Migrate to "new" image generation method. Device profiles will be generated
based on image/Makefile instead of profiles/ , which will also allow to
automatically build images for all supported devices via buildbot.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
The upstream board-2.bin file in the linux-firmware.git
repository for the QCA4019 contains a packed board-2.bin
for this device for both 2.4G and 5G wifis. This isn't
something that the ath10k driver supports.
Until this feature either gets implemented - which is
very unlikely -, or the upstream boardfile is mended
(both, the original submitter and ath10k-firmware
custodian have been notified). OpenWrt will go back
and use its own bespoke boardfile. This unfortunately
means that 2.4G and on some revisions the 5G WiFi is
not available in the initramfs image for this device.
Fixes: #12886
Reported-by: Christian Heuff <christian@heuff.at>
Debugged-by: Georgios Kourachanis <geo.kourachanis@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(cherry picked from commit 75505c5ec7)
When using an Intel AX210 card, the Bluetooth hci interface failed
to start due to a missing "ibt-0041-0041.sfi" file.
Bluetooth: hci0: Failed to load Intel firmware file intel/ibt-0041-0041.sfi (-2)
A device specific configuration file (DDC) is also required:
Bluetooth: hci0: Found device firmware: intel/ibt-0041-0041.sfi
Bluetooth: hci0: Waiting for firmware download to complete
...
Bluetooth: hci0: Found Intel DDC parameters: intel/ibt-0041-0041.ddc
Bluetooth: hci0: Applying Intel DDC parameters completed
Bluetooth: hci0: Firmware timestamp 2023.13 buildtype 1 build 62562
Fixes: #8558
Signed-off-by: Mathew McBride <matt@traverse.com.au>
(cherry picked from commit fff6833d4c)
This commit adds support for following wireless routers:
- Beeline SmartBox PRO (Serсomm S1500 AWI)
- WiFire S1500.NBN (Serсomm S1500 BUC)
This commit is based on this PR:
- Link: https://github.com/openwrt/openwrt/pull/4770
- Author: Maximilian Weinmann <x1@disroot.org>
The opening of this PR was agreed with author.
My changes:
- Sorting, minor changes and some movings between dts and dtsi
- Move leds to dts when possible
- Recipes for the factory image
- Update of the installation/recovery/return to stock guides
- Add reset GPIO for the pcie1
Common specification
--------------------
SoC: MediaTek MT7621AT (880 MHz, 2 cores)
Switch: MediaTek MT7530 (via SoC MT7621AT)
Wireless: 2.4 GHz, MT7602EN, b/g/n, 2x2
Wireless: 5 GHz, MT7612EN, a/n/ac, 2x2
Ethernet: 5 ports - 5×GbE (WAN, LAN1-4)
Mini PCIe: via J2 on PCB, not soldered on the board
UART: J4 -> GND[], TX, VCC(3.3V), RX
BootLoader: U-Boot SerComm/Mediatek
Beeline SmartBox PRO specification
----------------------------------
RAM (Nanya NT5CB128M16FP): 256 MiB
NAND-Flash (ESMT F59L2G81A): 256 MiB
USB ports: 2xUSB2.0
LEDs: Status (white), WPS (blue), 2g (white), 5g (white) + 10 LED Ethernet
Buttons: 2 button (reset, wps), 1 switch button (ROUT<->REP)
Power: 12 VDC, 1.5 A
PCB Sticker: 970AWI0QW00N256SMT Ver. 1.0
CSN: SG15********
MAC LAN: 94:4A:0C:**:**:**
Manufacturer's code: 0AWI0500QW1
WiFire S1500.NBN specification
------------------------------
RAM (Nanya NT5CC64M16GP): 128 MiB
NAND-Flash (ESMT F59L1G81MA): 128 MiB
USB ports: 1xUSB2.0
LEDs: Status (white), WPS (white), 2g (white), 5g (white) + 10 LED Ethernet
Buttons: 2 button (RESET, WPS)
Power: 12 VDC, 1.0 A
PCB Sticker: 970BUC0RW00N128SMT Ver. 1.0
CSN: MH16********
MAC WAN: E0:60:66:**:**:**
Manufacturer's code: 0BUC0500RW1
MAC address table (PRO)
-----------------------
use address source
LAN *:23 factory 0x1000 (label)
WAN *:24 factory $label +1
2g *:23 factory $label
5g *:25 factory $label +2
MAC addresses (NBN)
-------------------
use address source
LAN *:0e factory 0x1000
WAN *:0f LAN +1 (label)
2g *:0f LAN +1
5g *:10 LAN +2
OEM easy installation
---------------------
1. Remove all dots from the factory image filename (except the dot
before file extension)
2. Upload and update the firmware via the original web interface
3. Two options are possible after the reboot:
a. OpenWrt - that's OK, the mission accomplished
b. Stock firmware - install Stock firmware (to switch booflag from
Sercomm0 to Sercomm1) and then OpenWrt factory image.
Return to Stock
---------------
1. Change the bootflag to Sercomm1 in OpenWrt CLI and then reboot:
printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock2
reboot
2. Install stock firmware via the web OEM firmware interface
Recovery
--------
Use sercomm-recovery tool.
Link: https://github.com/danitool/sercomm-recovery
Tested-by: Pavel Ivanov <pi635v@gmail.com>
Tested-by: Denis Myshaev <denis.myshaev@gmail.com>
Tested-by: Oleg Galeev <olegingaleev@gmail.com>
Tested-By: Ivan Pavlov <AuthorReflex@gmail.com>
Co-authored-by: Maximilian Weinmann <x1@disroot.org>
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
(cherry picked from commit 2d6784a033)
