USXGMII link-up may fail due to too short delay after PLL reset.
Increase the delay to fix this.
Signed-off-by: Mantas Pucka <mantas@8devices.com>
Link: https://github.com/openwrt/openwrt/pull/18459
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Fixes to PCS driver to support 2.5G PHY
Signed-off-by: Mantas Pucka <mantas@8devices.com>
Link: https://github.com/openwrt/openwrt/pull/18459
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Missing bus clock prevent access to NSSCC registers and thus it is
impossible change clock configuration, when ethernet connection speed
changes.
Signed-off-by: Mantas Pucka <mantas@8devices.com>
Link: https://github.com/openwrt/openwrt/pull/18459
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add patches that fix:
* Wrong MSI interrups for PCIe3
* Hang during reboot due to stopped clocks
Signed-off-by: Mantas Pucka <mantas@8devices.com>
Link: https://github.com/openwrt/openwrt/pull/18459
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
CONFIG_QCOM_IPA kernel cofig was enabled by mistake and conflicts with
mac80211 as it indirectly selects QMI HELPERS. Backports project provid
his own version of QMI HELPERS hence it should not be built-in.
Link: https://github.com/openwrt/openwrt/pull/17788
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Make the RPM partition read-only. This was a mistake and a leftover from
staging branch but I can take this mistake as an excuse to document the
current problem with RPM.
It might happen that a board ship with a broken RPM .mbn, broken not in
the sense that the board doesn't boot or it's a brick but broken in the
sense that it's outdaed and suffer from a bug fixed in new version.
This bug consist in a problem with the regulators between USB and NSS.
The old RPM mess with the NSS regulator (l2) and change the voltage for
it while configuring the USB regulator (l5).
This cause the ethernet subsystem to malfunction with the port not
working.
To workaround this, it's needed to disable RPM handling and CPUFreq.
With these 2 disabled, the old RPM doesn't touch regulators and Ethernet
works correctly.
New RPM correctly handle regulators for USB (l5) and doesn't suffer from
this problem. A solution for this is getting discussed with QCOM hoping
to get some good feedback for it.
Link: https://github.com/openwrt/openwrt/pull/17788
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add pending patch fixing NSSCC boot stall. These patch are needed to
prevent the ICC to disable critical clock for NSSCC NOC.
Without these the system will stall and reboot with watchdog.
While at it also remove an extra clock from DTSI as it currently have no
use. Original patch is not modified to keep consistency with series
proposed upstream.
Link: https://github.com/openwrt/openwrt/pull/17788
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Drop redundant comment in NSSCC clock patch. The problem has been
identified hence the comment doesn't apply anymore.
Link: https://github.com/openwrt/openwrt/pull/17788
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Define default partition table for SPI-NAND mounted on reference board.
This is where is normally placed the rootfs UBI.
Link: https://github.com/openwrt/openwrt/pull/17788
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Refresh dts SPI-NAND patch to to v14. This is to keep stuff synced with
current pending patch revision and make it easier to replace patch
later (and discover something broke in the meantime)
Link: https://github.com/openwrt/openwrt/pull/17788
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Refresh the NSSCC patch for new PCIe patches. To keep track of fuzz
changes for the IPQ95xx patches, patch are not refreshed currently.
For the specific case of NSSCC patch, quilt gets confused and apply the
patch in the wrong node, putting it in the RPM node (causing all kind of
funny errors at runtime)
Correctly fix the patch to put the node right after the PCIe nodes.
Also the PORT patch need to be refreshed as the gpio header is added by
the PCIe patch.
Link: https://github.com/openwrt/openwrt/pull/17788
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add PCIe upstream patch and related nodes to enable PCIe on IPQ95xx.
Minimal change were required to backport the patch and apply on current
kernel. Refresh all affected patch.
Link: https://github.com/openwrt/openwrt/pull/17788
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add USB3 kmods to the default package list, USB3 correctly works on
IPQ95xx hence it can be enabled.
While at it drop the NSS-DP as it was added by mistake as the ethrnet
platform is handled differently on this SoC with pending upstream
drivers.
Link: https://github.com/openwrt/openwrt/pull/17788
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
QCOM SPI NAND driver got merged upstream hence we can drop the special
patch from qualcommax and qualcommbe target and move them to the generic
backports directory to reduce patch maintenance.
While at it refresh any affected patch and target and also backport other
minor fixup for the SPI NAND driver merged upstream later.
Link: https://github.com/openwrt/openwrt/pull/17788
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The CONFIG_NET_SWITCHDEV option is needed by CONFIG_DSA and some other
options. It is boolean, we have to compile it into the kernel it self.
Activate it for all targets in the generic configuration, it is already
activated for most of them. This allows to install DSA drivers as a
module.
On the ramips/mt7620 target the kernel would grown by 4.5kB.
For some small targets which do not support a DSA switch by default the
option is deactivated.
Link: https://github.com/openwrt/openwrt/pull/17668
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Refreshed patches for qualcommb/ipq95xx by running
make target/linux/refresh after creating a .config containing:
CONFIG_TARGET_qualcommbe=y
CONFIG_TARGET_qualcommbe_ipq95xx=y
CONFIG_TARGET_qualcommbe_ipq95xx_DEVICE_qcom_rdp433=y
Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/17822
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add patch to fix Qcom SNAND driver and move the SNAND patches to
backports directory as they are shared between qualcommax and qualcommbe
target.
Fixes: #17897
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17900
Signed-off-by: Robert Marko <robimarko@gmail.com>
Set target as source-only for now as only the Reference Board is
supported and needs to better evaluated with real Devices.
Link: https://github.com/openwrt/openwrt/pull/17725
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Enable the Aquantia PHY by default in config-defaults. Target is big
enough to permit embedding the PHY instead of having as an external
module.
Link: https://github.com/openwrt/openwrt/pull/17725
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Update patch with upstream version and automatically refresh with make
target/linux/refresh.
Also backport one additional fix patch for NAND patch and drop a patch
merged upstream.
Link: https://github.com/openwrt/openwrt/pull/17725
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add patch fixing unmet dependency for QCOM PPE. This fix a compilation
error when SFP config is selected.
Link: https://github.com/openwrt/openwrt/pull/17725
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add patches adding partition table common to RDP board and node for AQR
NVMEM.
Link: https://github.com/openwrt/openwrt/pull/17725
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add patch fixing USB regulator as the LDO needs to use ID 5 instead of
ID 2.
Link: https://github.com/openwrt/openwrt/pull/17725
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Backport CPUFreq patch and enable RPM. This is to enable CPU Frequency
scaling and regulators.
Link: https://github.com/openwrt/openwrt/pull/17725
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add initial support for new target with the initial patch for ethernet
support using pending upstream patches for PCS UNIPHY, PPE and EDMA.
Only initramfs currently working as support for new SPI/NAND
implementation, USB, CPUFreq and other devices is still unfinished and
needs to be evaluated.
Link: https://github.com/openwrt/openwrt/pull/17725
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
