openwrt/target/linux/ar71xx/base-files/etc/diag.sh

507 lines
7.7 KiB
Bash
Raw Normal View History

#!/bin/sh
# Copyright (C) 2009-2013 OpenWrt.org
. /lib/functions/leds.sh
. /lib/ar71xx.sh
get_status_led() {
local board=$(ar71xx_board_name)
case $board in
a40)
status_led="a40:green:status"
;;
a60)
status_led="a60:green:status"
;;
alfa-nx)
status_led="alfa:green:led_8"
;;
all0305)
status_led="eap7660d:green:ds4"
;;
antminer-s1|\
antminer-s3|\
antminer-r1|\
minibox-v1|\
ar71xx: add support for YunCore SR3200 and XD3200 YunCore SR3200 is a dual-band AC1200 router, based on Qualcomm/Atheros QCA9563+QCA9882+QCA8337N. YunCore XD3200 (FCC ID: 2ADUG-XD3200) is a dual-band AC1200 ceiling mount AP with PoE support, based on Qualcomm/Atheros QCA9563+QCA9882+QCA8334. Common specification: - 775/650/258 MHz (CPU/DDR/AHB) - 128 MB or RAM (DDR2) - 16 MB of FLASH (SPI NOR) - 2T2R 2.4 GHz, with ext. PA (SKY65174-21), up to 30 dBm - 2T2R 5 GHz, with ext. PA (SKY85405-11) and LNA (SKY85601-11), up to 30 dBm SR3200 specification: - 5x 10/100/1000 Mbps Ethernet - 6x ext. RP-SMA antennas (actually, only 4 are connected with radio chips) - 3x LED (+ 5x LED in RJ45 sockets), 1x button - UART header on PCB XD3200 specification: - 2x 10/100/1000 Mbps Ethernet, with 802.3at PoE support (WAN port) - 4x internal antennas - 3 sets of LEDs on external PCB (+ 2x LED near RJ45 sockets), 1x button - UART and JTAG (custom 6-pin, 2 mm pitch) headers on PCB LED for 5 GHz WLAN is currently not supported on both devices as it is connected directly to the QCA9882 radio chip. Flash instruction under vendor firmware, using telnet/SSH: 1. If your firmware does not have root password, go to point 5 2. Connect PC with 192.168.1.x address to LAN or WAN port 3. Power up device, enter failsafe mode with button (no LED indicator!) 4. Change root password and reboot (mount_root, passwd ..., reboot -f) 5. Upload lede-ar71xx-...-sysupgrade.bin to /tmp using SCP 6. Connect PC with 192.168.188.x address to LAN port, SSH to 192.168.188.253 7. Invoke: - cd /tmp - fw_setenv bootcmd "bootm 0x9fe80000 || bootm 0x9f050000" - mtd -e firmware -r write lede-ar71xx-...-sysupgrade.bin firmware Flash instruction under U-Boot, using UART: 1. tftp 0x80060000 lede-ar71xx-...-sysupgrade.bin 2. erase 0x9f050000 +$filesize 3. cp.b $fileaddr 0x9f050000 $filesize 4. setenv bootcmd "bootm 0x9fe80000 || bootm 0x9f050000" 5. saveenv && reset Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-12-02 21:42:41 +00:00
som9331|\
sr3200|\
tl-wr802n-v2|\
ar71xx: add support for YunCore SR3200 and XD3200 YunCore SR3200 is a dual-band AC1200 router, based on Qualcomm/Atheros QCA9563+QCA9882+QCA8337N. YunCore XD3200 (FCC ID: 2ADUG-XD3200) is a dual-band AC1200 ceiling mount AP with PoE support, based on Qualcomm/Atheros QCA9563+QCA9882+QCA8334. Common specification: - 775/650/258 MHz (CPU/DDR/AHB) - 128 MB or RAM (DDR2) - 16 MB of FLASH (SPI NOR) - 2T2R 2.4 GHz, with ext. PA (SKY65174-21), up to 30 dBm - 2T2R 5 GHz, with ext. PA (SKY85405-11) and LNA (SKY85601-11), up to 30 dBm SR3200 specification: - 5x 10/100/1000 Mbps Ethernet - 6x ext. RP-SMA antennas (actually, only 4 are connected with radio chips) - 3x LED (+ 5x LED in RJ45 sockets), 1x button - UART header on PCB XD3200 specification: - 2x 10/100/1000 Mbps Ethernet, with 802.3at PoE support (WAN port) - 4x internal antennas - 3 sets of LEDs on external PCB (+ 2x LED near RJ45 sockets), 1x button - UART and JTAG (custom 6-pin, 2 mm pitch) headers on PCB LED for 5 GHz WLAN is currently not supported on both devices as it is connected directly to the QCA9882 radio chip. Flash instruction under vendor firmware, using telnet/SSH: 1. If your firmware does not have root password, go to point 5 2. Connect PC with 192.168.1.x address to LAN or WAN port 3. Power up device, enter failsafe mode with button (no LED indicator!) 4. Change root password and reboot (mount_root, passwd ..., reboot -f) 5. Upload lede-ar71xx-...-sysupgrade.bin to /tmp using SCP 6. Connect PC with 192.168.188.x address to LAN port, SSH to 192.168.188.253 7. Invoke: - cd /tmp - fw_setenv bootcmd "bootm 0x9fe80000 || bootm 0x9f050000" - mtd -e firmware -r write lede-ar71xx-...-sysupgrade.bin firmware Flash instruction under U-Boot, using UART: 1. tftp 0x80060000 lede-ar71xx-...-sysupgrade.bin 2. erase 0x9f050000 +$filesize 3. cp.b $fileaddr 0x9f050000 $filesize 4. setenv bootcmd "bootm 0x9fe80000 || bootm 0x9f050000" 5. saveenv && reset Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-12-02 21:42:41 +00:00
xd3200)
status_led="$board:green:system"
;;
ap132|\
ap531b0|\
db120|\
dr344|\
tew-632brp|\
wpj344|\
zbt-we1526)
status_led="$board:green:status"
;;
ap136-010|\
ap136-020)
status_led="ap136:green:status"
;;
ap147-010)
status_led="ap147:green:status"
;;
ap135-020)
status_led="ap135:green:status"
;;
ar71xx: add support to TP-Link Archer C59v1 and C60v1 TP-Link Archer C59v1 is a dual-band AC1350 router, based on Qualcomm/Atheros QCA9561+QCA9886. Specification: - 775/650/258 MHz (CPU/DDR/AHB) - 128 MB of RAM (DDR2) - 16 MB of FLASH (SPI NOR) - 3T3R 2.4 GHz - 2T2R 5 GHz - 5x 10/100 Mbps Ethernet - USB 2.0 port - 8x LED (controled by 74HC595), 3x button - UART header on PCB TP-Link Archer C60v1 is a dual-band AC1350 router, based on Qualcomm/Atheros QCA9561+QCA9886. Specification: - 775/650/258 MHz (CPU/DDR/AHB) - 64 MB of RAM (DDR2) - 8 MB of FLASH (SPI NOR) - 3T3R 2.4 GHz - 2T2R 5 GHz - 5x 10/100 Mbps Ethernet - 7x LED, 2x button - UART header on PCB Currently not working: - Port LAN1 on C59, LAN4 on C60 - WiFi 5GHz (missing ath10k firmware for QCA9886 chip) - Update from oficial web interface ( tplink-saveloader not support "product-info") Flash instruction: 1. Set PC to fixed ip address 192.168.0.66 2. Download lede-ar71xx-generic-archer-cXX-v1-squashfs-factory.bin and rename it to tp_recovery.bin 3. Start a tftp server with the file tp_recovery.bin in its root directory 4. Turn off the router 5. Press and hold Reset button 6. Turn on router with the reset button pressed and wait ~15 seconds 7. Release the reset button and after a short time the firmware should be transferred from the tftp server 8. Wait ~30 second to complete recovery. Flash instruction under U-Boot, using UART: 1. tftp 0x81000000 lede-ar71xx-...-sysupgrade.bin 2. erase 0x9f020000 +$filesize 3. cp.b $fileaddr 0x9f020000 $filesize 4. reset Signed-off-by: Henryk Heisig <hyniu@o2.pl> [Jo-Philipp Wich: remove duplicate ATH79_MACH_ARCHER_C59/C60_V1 entries] Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2016-12-27 21:41:41 +00:00
archer-c59-v1|\
archer-c60-v1|\
mr12|\
mr16|\
nbg6616|\
sc1750|\
sc450|\
tl-wpa8630)
status_led="$board:green:power"
;;
ap90q|\
cpe830|\
cpe870|\
gl-inet|\
gl-mifi|\
gl-ar300m)
status_led="$board:green:lan"
;;
ap96)
status_led="$board:green:led2"
;;
aw-nr580)
status_led="$board:green:ready"
;;
bhr-4grv2|\
wzr-hp-ag300h|\
wzr-hp-g300nh2)
status_led="buffalo:red:diag"
;;
bsb)
status_led="$board:red:sys"
;;
bullet-m|\
rocket-m|\
rocket-m-xw|\
nano-m|\
nanostation-m|\
nanostation-m-xw|\
loco-m-xw)
status_led="ubnt:green:link4"
;;
rocket-m-ti)
status_led="ubnt:green:link6"
;;
bxu2000n-2-a1)
status_led="bhu:green:status"
;;
cap324)
status_led="pcs:green:power"
;;
c-55|\
c-60)
status_led="$board:green:pwr"
;;
cap4200ag)
status_led="senao:green:pwr"
;;
cf-e316n-v2|\
cf-e520n|\
cf-e530n)
status_led="$board:blue:wan"
;;
cf-e320n-v2)
status_led="$board:blue:wlan"
;;
cf-e380ac-v1|\
cf-e380ac-v2)
status_led="$board:blue:wlan2g"
;;
cpe510)
status_led="tp-link:green:link4"
;;
cr3000)
status_led="pcs:amber:power"
;;
cr5000)
status_led="pcs:amber:power"
;;
dgl-5500-a1|\
dhp-1565-a1|\
dir-505-a1|\
dir-600-a1|\
dir-615-e1|\
dir-615-i1|\
dir-615-e4)
status_led="d-link:green:power"
;;
dir-615-c1)
status_led="d-link:green:status"
;;
dir-825-b1)
status_led="d-link:orange:power"
;;
dir-825-c1|\
dir-835-a1)
status_led="d-link:amber:power"
;;
dir-869-a1)
status_led="d-link:white:status"
;;
dlan-hotspot)
status_led="devolo:green:wifi"
;;
dlan-pro-500-wp)
status_led="devolo:green:wlan-2g"
;;
dlan-pro-1200-ac)
status_led="devolo:status:wlan"
;;
dr531)
status_led="$board:green:sig4"
;;
dragino2|\
oolite)
status_led="$board:red:system"
;;
dw33d)
status_led="$board:blue:status"
;;
eap120)
status_led="$(ar71xx_board_name):green:system"
;;
eap300v2)
status_led="engenius:blue:power"
;;
eap7660d)
status_led="$board:green:ds4"
;;
el-mini|\
el-m150)
status_led="easylink:green:system"
;;
ew-dorin|\
ew-dorin-router)
status_led="dorin:green:status"
;;
f9k1115v2)
status_led="belkin:blue:status"
;;
epg5000|\
esr1750)
status_led="$board:amber:power"
;;
esr900)
status_led="engenius:amber:power"
;;
hiwifi-hc6361)
status_led="hiwifi:blue:system"
;;
hornet-ub|\
hornet-ub-x2)
status_led="alfa:blue:wps"
;;
ja76pf|\
ja76pf2)
status_led="jjplus:green:led1"
;;
jwap230)
status_led="$board:green:led1"
;;
ls-sr71)
status_led="ubnt:green:d22"
;;
mc-mac1200r)
status_led="mercury:green:system"
;;
mr18|\
z1)
status_led="$board:green:tricolor0"
;;
mr600)
status_led="$board:orange:power"
;;
mr600v2)
status_led="mr600:blue:power"
;;
mr1750|\
mr1750v2)
status_led="mr1750:blue:power"
;;
mr900|\
mr900v2)
status_led="mr900:blue:power"
;;
mynet-n600|\
mynet-n750)
status_led="wd:blue:power"
;;
mynet-rext)
status_led="wd:blue:power"
;;
mzk-w04nu|\
mzk-w300nh)
status_led="planex:green:status"
;;
nbg460n_550n_550nh)
status_led="nbg460n:green:power"
;;
nbg6716)
status_led="$board:white:power"
;;
om2p|\
om2pv2|\
om2pv4|\
om2p-hs|\
om2p-hsv2|\
om2p-hsv3|\
om2p-hsv4|\
om2p-lc)
status_led="om2p:blue:power"
;;
om5p|\
om5p-an)
status_led="om5p:blue:power"
;;
om5p-ac|\
om5p-acv2)
status_led="om5pac:blue:power"
;;
omy-g1)
status_led="omy:green:wlan"
;;
omy-x1)
status_led="omy:green:power"
;;
onion-omega)
status_led="onion:amber:system"
;;
pb44)
status_led="$board:amber:jump1"
;;
rb-2011l|\
rb-2011uas|\
rb-2011uas-2hnd)
status_led="rb:green:usr"
;;
rb-411|\
rb-411u|\
rb-433|\
rb-433u|\
rb-450|\
rb-450g|\
rb-493)
status_led="rb4xx:yellow:user"
;;
rb-750)
status_led="rb750:green:act"
;;
rb-750-r2|\
rb-750up-r2|\
rb-911g-2hpnd|\
rb-911g-5hpacd|\
rb-911g-5hpnd|\
rb-912uag-2hpnd|\
rb-912uag-5hpnd|\
rb-941-2nd|\
rb-951ui-2nd|\
rb-952ui-5ac2nd|\
rb-962uigs-5hact2hnt|\
rb-lhg-5nd|\
rb-mapl-2nd)
status_led="rb:green:user"
;;
rb-951ui-2hnd)
status_led="rb:green:act"
;;
rb-sxt2n|\
rb-sxt5n)
status_led="rb:green:power"
;;
re450|\
sc300m)
status_led="$board:blue:power"
;;
routerstation|\
routerstation-pro)
status_led="ubnt:green:rf"
;;
rw2458n)
status_led="$board:green:d3"
;;
smart-300)
status_led="nc-link:green:system"
;;
qihoo-c301)
status_led="qihoo:green:status"
;;
tellstick-znet-lite)
status_led="tellstick:white:system"
;;
tew-673gru)
status_led="trendnet:blue:wps"
;;
tew-712br|\
tew-732br|\
tew-823dru)
status_led="trendnet:green:power"
;;
tl-mr3020)
status_led="tp-link:green:wps"
;;
tl-wa750re)
status_led="tp-link:orange:re"
;;
tl-wa850re|\
tl-wa850re-v2)
status_led="tp-link:blue:re"
;;
tl-wa860re)
status_led="tp-link:green:power"
;;
tl-mr3220|\
tl-mr3220-v2|\
tl-mr3420|\
tl-mr3420-v2|\
tl-wa701nd-v2|\
tl-wa801nd-v2|\
tl-wa901nd|\
tl-wa901nd-v2|\
tl-wa901nd-v3|\
tl-wa901nd-v4|\
tl-wdr3320-v2|\
tl-wdr3500|\
tl-wr1041n-v2|\
tl-wr1043nd|\
tl-wr1043nd-v2|\
tl-wr1043nd-v4|\
tl-wr741nd|\
tl-wr741nd-v4|\
tl-wa801nd-v3|\
tl-wr841n-v1|\
tl-wr841n-v7|\
tl-wr841n-v8|\
tl-wr841n-v11|\
tl-wa830re-v2|\
tl-wr842n-v2|\
tl-wr842n-v3|\
tl-wr941nd|\
tl-wr941nd-v5)
status_led="tp-link:green:system"
;;
archer-c5|\
archer-c7|\
tl-wdr4900-v2|\
tl-mr10u|\
tl-mr12u|\
tl-mr13u|\
tl-wdr4300|\
tl-wr703n|\
tl-wr710n|\
tl-wr720n-v3|\
tl-wr802n-v1|\
tl-wr810n|\
tl-wr940n-v4|\
tl-wr941nd-v6)
status_led="tp-link:blue:system"
;;
tl-wr841n-v9)
status_led="tp-link:green:qss"
;;
tl-wr2543n)
status_led="tp-link:green:wps"
;;
tl-wdr6500-v2)
status_led="tp-link:white:system"
;;
tube2h)
status_led="alfa:green:signal4"
;;
unifi)
status_led="ubnt:green:dome"
;;
uap-pro|\
unifiac-lite|\
unifiac-pro)
status_led="ubnt:white:dome"
;;
unifi-outdoor-plus)
status_led="ubnt:white:front"
;;
airgateway|\
airgatewaypro)
status_led="ubnt:white:status"
;;
whr-g301n|\
whr-hp-g300n|\
whr-hp-gn|\
wzr-hp-g300nh)
status_led="buffalo:green:router"
;;
wlae-ag300n)
status_led="buffalo:green:status"
;;
r6100|\
wndap360|\
wndr3700|\
wndr3700v4|\
wndr4300|\
wnr2000|\
wnr2000-v3|\
wnr2200|\
wnr612-v2|\
wnr1000-v2|\
wpn824n)
status_led="netgear:green:power"
;;
wp543)
status_led="$board:green:diag"
;;
wpj342|\
wpj531|\
wpj558)
status_led="$board:green:sig3"
;;
wrt400n|\
wrt160nl)
status_led="$board:blue:wps"
;;
zcn-1523h-2|\
zcn-1523h-5)
status_led="zcn-1523h:amber:init"
;;
wlr8100)
status_led="sitecom:amber:status"
;;
esac
}
set_state() {
get_status_led
case "$1" in
preinit)
status_led_blink_preinit
;;
failsafe)
status_led_blink_failsafe
;;
preinit_regular)
status_led_blink_preinit_regular
;;
done)
status_led_on
case $(ar71xx_board_name) in
gl-ar300m)
fw_printenv lc >/dev/null 2>&1 && fw_setenv "bootcount" 0
;;
qihoo-c301)
local n=$(fw_printenv activeregion | cut -d = -f 2)
fw_setenv "image${n}trynum" 0
;;
esac
;;
esac
}