If the PIT timer driver gets activated too slow (e.g. because of a bad priority
configuration), it might miss counter wraps and would than produce sudden time
jumps. The driver now detects this problem dynamically, warns about it and
adapts the affected values to avoid time jumps.
Ref #2400
The cache directory content is slightly different on each prepare-port
run and fortunately not used at build time. So, we just remove it at the
end of port preparation.
When using the elfweaver to generate boot images, python stores
precompiled modules in the source directory besides the .py files. This
changed the contrib source tree with binary files specific to the build
host. As a result the depot create tool picked up the changed source
tree and produced strange new hashes. Now, the tool sources are copied
to the build directory where python can do its optimizations and the
depot stays clean.
The NIC router always reports the link state "Up" (true) because
the effective link state depends on the targeted remote interface
and thus on the individual routing for each packet. Consequently,
also the signal handler for state changes gets ignored.
Ref #2490
IP stacks may treat a network interface as "down" when it states a MAC
address with the I/G bit (bit 40) set to "Group" (value 0) instead of
"Individual" (value 1). This was observed with a TinyCore 8 inside a
Virtualbox VM. Thus, the previously choosen 03:03:03:03:03:00 as base
for the MAC address allocator is bad. Now we use the 02:02:02:02:02:00
instead. This also ensures that the MAC addresses are not marked as
"Universal" but as "Local" (bit 41, value 1) which is correct in general
as the router allocates MAC addresses only for virtual networks.
Ref #2490
The timer driver should always be of the highest priority to avoid
problem with timers that have low max-counter values like the PIT
with only 53 ms.
Ref #2400
The NIC dump component didn't support forwarding of link states and link-state
signals until now. Furthermore, it now prints MAC address and link state
on session creation and on every link state change.
Ref #2490
Previously, the uplink session was created on component startup while the
creation of the downlink session is timed by the client component. This
created a time span in which packets from the uplink were dropped at the
nic_dump. Now the uplink session-request is done by the session component
of the downlink.
Ref #2490
Add a "writeable" policy option to the ahci_drv and part_blk Block
servers and default from writeable to ready-only. Should a policy
permit write acesss the session request argument "writeable" may still
downgrade a session to ready-only.
Fix#2469
This should actually never happen. However if it happens, be a bit robuster
and don't provide the memory for re-use (which causes tons of other trouble
afterwards).
Issue #2505
Some x86 machines do have a LAPIC speed < 1000 ticks per millisecond
when configured to use the maximum divider (as it was always the case).
But we need microseconds precision for the timeout framework. Thus,
reduce the divider dynamically until the frequency fullfills our
requirements.
Ref #2400
There are hardware timers whose frequency can't be expressed as
ticks-per-microsecond integer-value because only a ticks-per-millisecond
integer-value is precise enough. We don't want to use expensive
floating-point values here but nonetheless want to translate from ticks
to time with microseconds precision. Thus, we split the input in two and
translate both parts separately. This way, we can raise precision by
shifting the values to their optimal bit position. Afterwards, the results
are shifted back and merged together again.
As this algorithm is not so trivial anymore and used by at least three
timer drivers (base-hw/x86_64, base-hw/cortex_a9, timer/pit), move it to a
generic header to avoid redundancy.
Ref #2400
Due to the simplicity of the algorithm that translated from timer ticks
to time, we lost microseconds precision although the timer allows for it.
Ref #2400
Due to the simplicity of the algorithm that translated from timer ticks
to time, we lost microseconds precision although the timer allows for it.
Ref #2400
When synchronizing with the remote time source, we have to take care that the
measured time difference cannot become null because its real value is smaller
than the measurement granularity. Since the granularity is one microsecond, we
simply go on polling timestamp and time until the microsecond has passed.
This busy waiting should be no problem for the system for two reasons. First,
it is limited to a relatively small amount of time and second, a busy lock
does not happen because the time source that is responsible for the limiting
factor is explicitely called on each poll.
Ref #2400
When building Genode on a Linux system running in a Xen Dom0, the 'xen'
run target can run a Genode scenario in a Xen DomU.
Usage: in build/x86_*/etc/build.conf, define:
RUN_OPT = --include boot_dir/$(KERNEL) --include image/iso --include power_on/xen --include log/xen --include power_off/xen
The Xen DomU runs in HVM mode and loads Genode from an ISO image. Serial
log output is printed to the console and graphical output is shown in an
SDL window.
The Xen DomU ist managed using the 'xl' command line tool and it is
possible to add configuration options in the 'xen_args' variable in a run
script. Common options are:
- disabling the graphical output:
append xen_args { sdl="0" }
- configuring a network device:
append xen_args { vif=\["model=e1000,mac=02:00:00:00:01:01,bridge=xenbr0"\] }
- configuring USB input devices:
append xen_args { usbdevice=\["mouse","keyboard"\] }
Note: the 'xl' tool requires super-user permissions and interactive
password input can be troublesome in combination with 'expect' and is not
practical for automatic tests. For this reason, the current implementation
assumes that no password input is needed when running 'sudo xl', which can
be achieved by creating a file '/etc/sudoers.d/xl' with the content
'user ALL=(root) NOPASSWD: /usr/sbin/xl'
(where 'user' is the Linux user name).
Fixes#2504
When running core as the kernel inside every component, a separate
stack area for core is needed that is different from the user-land
component's one.
Ref #2091
Acquire Signal_context objects locks via Object_pool::apply() in the
context of the entrpyoint thread, instead in the context of the calling
thread.
Fixes#2485
The files are generated via flex and bison. Until now, this step was
performed when preparing the libc port. Unfortunately, the generated
files have subtle differences depending on the flex/bison versions
installed in the host. For example, the bison version number appears in
the generated code. This, in turn, breaks the hash mechanism of the
depot where a src/libc archive ends up being slightly different when
created on different hosts.
By moving the code generation to the build stage, the src/libc archive
merely contains the nslexer.l and nsparser.y source files but not the
generated files.
- Fix fatal exception handling so that stack traces are dumped
- Add 'include/nim' directories to Nim module search path
- Enable release optimizations for release builds
Fix#2493
This patch removes the assertion about the unexpected call of
'block_for_signal' within core. On Linux, this call is actually
expected because of the handling of SIGCHLD signals by core.
When idle, menu_view de-schedules timer events to save processing time.
Once reactivated by a dialog update, it computes the passed time and
applies the result to the animator. However, the animation was most likely
started by the update not during the sleep. So the passed time must not
be applied to the animation in this case. Otherwise, many animation steps
are computed at once within a single visible frame.
Furthermore, the patch adjusts the REDRAW_PERIOD to 2, which is a better
value for geometric movements as opposed to mere color-blending effects
where the frame rate does not matter so much.
It also refines the nitpicker-buffer relocation in a way that extends
the buffer but does not shrink it. This lowers the interaction with
nitpicker in situations where the dialog size changes a lot.
By applying the text output to the alpha buffer in addition to the pixel
buffer, labels can now appear without the need for an underlying frame
or button.
The new widget allows one to align a child widget within a larger parent
widget by specifying the boolean attributes 'north', 'south', 'east',
and 'west'. If none is specified, the child is centered. If opposite
attributes are specified, the child is stretched.
This improves the output quality of antialiased lines onto a transparent
nitpicker buffer. For antialiased graphics operations, the initial color
leaks through. Leaking 50% gray is better than leaking black, in
particular when drawing white lines.
This patch makes the use of 'List' invisible at the 'Animator'
interface. This allows users of the utility to keep 'Animator::Items' in
a custom 'List' with no aliasing problems.
The VFS library can be used in single-threaded or multi-threaded
environments and depending on that, signals are handled by the same thread
which uses the VFS library or possibly by a different thread. If a VFS
plugin needs to block to wait for a signal, there is currently no way
which works reliably in both environments.
For this reason, this commit makes the interface of the VFS library
nonblocking, similar to the File_system session interface.
The most important changes are:
- Directories are created and opened with the 'opendir()' function and the
directory entries are read with the recently introduced 'queue_read()'
and 'complete_read()' functions.
- Symbolic links are created and opened with the 'openlink()' function and
the link target is read with the 'queue_read()' and 'complete_read()'
functions and written with the 'write()' function.
- The 'write()' function does not wait for signals anymore. This can have
the effect that data written by a VFS library user has not been
processed by a file system server yet when the library user asks for the
size of the file or closes it (both done with RPC functions at the file
system server). For this reason, a user of the VFS library should
request synchronization before calling 'stat()' or 'close()'. To make
sure that a file system server has processed all write request packets
which a client submitted before the synchronization request,
synchronization is now requested at the file system server with a
synchronization packet instead of an RPC function. Because of this
change, the synchronization interface of the VFS library is now split
into 'queue_sync()' and 'complete_sync()' functions.
Fixes#2399
This patch changes init's service forwarding such that pending requests
are kept unanswered as long as the requested service is not present
(yet). In dynamic-init scenarios, this is needed in situtions where the
dynamic init is known to eventually provide the service but the internal
subsystem is not ready yet. Previously, a client that attempted to
request a session in this early phase would get a 'Service_denied'
exception. By deferring the forwarding in this situation, the behaviour
becomes deterministic.
If a matching '<service>' exists but there is no matching policy sub
node, the request is answered with 'Service_denied' - as expected.
A boot module with size 0 previously made Core crash with a page fault in
Region_map_component::attach. This patch prevents the creation of ROM-FS
entries for such modules.
Ref #2490
For most base platforms (except linux and sel4), the initialization of
boot modules is the same. Thus, merge this default implementation in the
new unit base/src/core/platform_rom_modules.cc.
Ref #2490
In Region_map_component::attach, storing the metadata for a region may
throw an exception. Catch it and throw an Invalid_dataspace exception.
Ref #2490
Currently, init does not test wether a service is abandoned on a new
configuration if the service was routed via an any-child route. Trigger
this behaviour in the init test.
Ref #2483
We used a hardware timer locally in the RPI USB driver because a timer
connection was not precise enough to fullfill the host controllers
requirements.
With the modern timer connection interface, however, reading out time at
a connection is microseconds precise and we can remove the local timer.
But we cannot use the same timer connection for doing legacy-interface
stuff like usleep (currently used in LX kit) and modern-interface stuff
like curr_time. Thus, we open two connections for now.
Ref #2400
The calibration of the interpolation parameters was previously only done
periodically every 500 ms. Together with the fact that the parameters
had to be stable for at least 3 calibration steps to enable
interpolation, it took at least 1.5 seconds after establishing a
connection to get microseconds-precise time values.
This is a problem for some drivers that directly start to poll time.
Thus, the timer connection now does a calibration burst as soon as it
switches to the modern mode (the mode with microseconds precision).
During this phase it does several (currently 9) calibration steps
without a delay inbetween. It is assumed that this is fast enough to not
get interrupted by scheduling. Thus, despite being small, the measured
values should be very stable which is why the burst should in most cases
be sufficient to get the interpolation initialized.
Ref #2400
When in modern mode (with local time interpolation), the timer
connection used to maximize the left shifting of its
timestamp-to-microseconds factor. The higher the shift the more precise
is the translation from timestamps to microseconds. If the timestamp
values used for determining the best shift were small - i.e. the delay
between the calibration steps were small - we may got a pretty big
shift. If we then used the shift with bigger timestamp values - i.e.
called curr_time seldom or raised calibration delays - the big shift
value became a problem. The framework had to scale down all measured
timestamps and time values temporarily to stay operative until the next
calibration step.
Thus, we now raise the shift only that much that the resulting factor
fullfills a given minimum. This keeps it as low as possible according
to the precision requirement. Currently, this requirement is set to 8
meaning that the shifted factor shall be at least 2^8 = 256.
Ref #2400
The kernel timer on RPI is able to measure time microseconds-precise.
Howeer, due to a bug, we dropped precision during the ticks-to-time
translation and return only milliseconds-precise time.
Ref #2400
As the timer session now provides a method 'elapsed_us', there is no more need
for doing any internal calculations with values of milliseconds.
Ref #2400
As timer sessions are not expected to be microseconds precise (because
of RPC latency and scheduling), the session interface provided only a
method 'elapsed_ms' although the back end of this method in the timer
driver works with microseconds.
However, in some cases it makes sense to have a method 'elapsed_us'. The
values it returns might be milliseconds away from the "real" time but it
allows you to work with delays smaller than a millisecond without
getting a zero delta value.
This commit is motivated by the need for fast bursts of calibration
steps for the time interpolation in the new timer connection.
Ref #2400
The filename buffer of a dataspace in base-linux is limited to
40 bytes. When using file names longer than this, the remainder
gets dropped silently. Add an error message to aid debugging this
case.
This is helpful for disabling messages in etc/tools.conf by
setting it to e.g.
MSG_LINK = @true ""
This results in much shorter and less cluttered logs in automatic
builds.
- factor out Rm_client::pager lambda code into utility
Region_map_component::create_map_item
- use utility to find/lookup physical addresses to be mapped eagerly
Issue #2209
The launcher.run scenario was last updated mid-may of the recently
developed cap-quota accounting (before all cap types were covered).
Hence, the quotas used in the scenario are too low. This patch adjusts
the values such that the scenario can be started on NOVA on Qemu. It
also fixes a warning about a deprecated way of configuring the
report_rom component.
Thanks to Jörg-Christian Böhme for reporting!
- Update FatFS port from 0.07e to 0.13
- Multi-device support
- Basic test at run/fatfs
- Adaption of existing components
Note, ffat is now consistently renamed to fatfs.
Ref #2410
rm_fault.run triggers write on read-only ROM provided by core, which
fails without this patch:
arm - "raised unhandled data abort"
x86 - (silent/invisible) busy loop because write fault gets never resolved
The run script did not consider the routing for the environment ROM
sessions for the test-iso component. It routed all ROM sessions -
including the ones for the executable and the dynamic linker - to
fs_rom. The patch also adds the cap quota definitions required since
version 17.05 and fixes a whitespace inconsistency between the test
program and the run script.
Thanks to Steven Harp for reporting!
This is expected by hardware terminals, ie., terminal programs connected
to null-modem serial connections. Otherwise, the next line starts at the
column right after the last line.
Platform_pd "_pd" uses a allocator for, which relies on the mapped RAM
dataspace within core. Unfortunately the RAM dataspaces are already freed up
during _ram_ds_factory destruction, which may lead to trouble if accessed
afterwards.
Issue #2451
The new version of the test exercises the combination of fs_report with
ram_fs and fs_rom as a more flexible alternative to report_rom.
It covers two corner cases that remained unaddressed by fs_rom and
ram_fs so far: First, the late installation of a ROM-update signal
handler at fs_rom right before the content of the file is modified.
Second, the case where the requested file is not present on the file
system at the creation time of the ROM session. Here, the ram_fs missed
to inform listeners for the compound directory about the later created
file.
This patch ensures that fs_rom delivers a ROM-update notification in the
case where the underlying file was changed in-between requesting the
initial ROM content and registering the signal handler.
With the introduction of the CONTENT_CHANGED notifications delivered via
the packet stream, the assumption that no more than one READ packet is
in flight at all times does no longer hold. If the fs server responds
to a CONTENT_CHANGED packet while the fs_rom expects the completion of a
read request, the '_update_dataspace' method would prematurely return,
leaving the dataspace unpopulated. This patch solves the problem by
specifically waiting for the completion of the read request.
Session_requester inherits from Dynamic_rom_session::Content_producer
which specifies the Buffer_capacity_exceeded exception which is thrown
on insufficient buffer space.
This patch sets the -march complile flag in spec/arm_v7a.mk, which
enables us to build depot archives for the 'arm_v7a' architecture.
It also removes copy-pasted comments that offer no valuable insights but
contain grammar errors.
On platforms that use the PIT timer driver, 'elapsed_ms' is pretty
inprecise/unsteady (up to 3 ms deviation) for a reason that is not
clearly determined yet. On Fiasco and Fiasco.OC, that use kernel timing,
it is the same. So, on these platforms, our locally interpolated time
seems to be fine but the reference time is bad. Until this is fixed, we
raise the error tolerance for these platforms in the run script.
Ref #2400
Appending a suffix to report filenames was behavior inherited from
fs_log, it prevents creating files where directories need to be created
later. But unlike logs, only a subset of the hierarchy will report and
those that do append a component-local label, so the risk of collision
is low.
By removing the suffix fs_rom can serve reports back as ROM just as
report_rom does.
Ref #2422
A bug in the timer-ticks-to-microseconds translation of the kernel timer
caused the user time to periodically get stuck for about 32 milliseconds
and then jump forward to the normal level again.
Ref #2400
In the timeout framework, we maintain a translation factor value to
translate between time and timestamps. To raise precision we scale-up
the factor when we calculate it and scale-down the result of its
appliance later again. This up and down scaling is achieved through
left and right shifting. Until now, the shift width was statically
choosen. However, some platforms need a big shift width and others a
smaller one. The one static shift width couldn't cover all platforms
which caused overflows or precision problems.
Now, the shift width is choosen optimally for the actual translation
factor each time it gets re-calculated. This way, we can take care that
the shift always renders the best precision level without the risk for
overflows.
Ref #2400
The result-buffer related members of the fast polling test are
the same for each buffered result type. Thus, we can make the
code easier by providing them through a struct.
Ref #2400
This patch increases init's preserved RAM and capability quota to
account for a current limitation of init with respect to the creation of
sessions to parent services:
In contrast to regular routed services, sessions to parent services are
created via 'Env::session'. The implementation of 'Env::session'
automatically upgrades session quotas on demand, which is the desired
behavior for regular 'Connection' objects. However, for sessions
established on the behalf of init's children, we would need to reflect
the error condition to the child instead of resolving it locally within
init (by subsidizing the session with init's quota). This patch leaves
this issue unresolved but fixes the symptom for the bomb test. It is
meant as an interim solution until the handling of parent sessions is
revised.
This patch decouples the error handling of the quota transfers
and the actual session creation. In the previous version, an error in
the 'initiate_request' phase would leave the local scope via an
exception without disarming the transfer guard objects. This way,
the guard destructors would attempt the returning of session quota in
addition to the explicit call of '_revert_quota_and_destroy' as done in
the error handling of the 'initiate_request' operation.
In the presence of a session-creation error in the 'initiate_request'
phase, session quota would eventually be returned twice. This patch
removes the intertwined error handling of both phases in a way that the
guards of the first phase (quota transfer) are no longer present in the
second phase (initiate_request).
This patch makes sure that the initial PD session limit (as defined by
the client-provided session quota) is preserved over the entire lifetime
of the PD session. That means, it cannot be transferred to other PD
sessions. Otherwise, it may be impossive to hand back all the static
session quota to the PD-session client at session-destruction time
because parts of the initial quota would no longer belong to the
session.
Note that the initial limit can still be used for allocations within the
PD session as those allocations are automatically reverted at
session-destruction time.
The implementations of the lock and C++ guards tests depend on
thread-execution priorities, which produces false negatives of the whole
thread test on platforms without priority support.
On QEMU, NOVA uses the pretty unstable TSC emulation as primary time
source. Thus, timeouts do not trigger with the common precision (< 50
ms). Use an error tolerance of 200 ms for this platform constellation.
Ref #2400
Apparently this construct leads to a compiler errors like
error: second operand to the conditional operator is of type ‘void’, but
the third operand is neither a throw-expression nor of type ‘void’
The fast polling test uses one timer session for raw 'elapsed_ms' calls
and another one for potentially interpolated 'curr_time' calls. It then
compares the two results against each other. However, until now, the
test did not consider that the duration of the session construction may
create a remarkable shift between the local times of the two sessions.
This shift is now determined and compensated before doing any
comparison.
Ref #2400
The multiple-handlers test was checking if handlers at one signal were
activated in a fair manner. But on Qemu, the error tolerance of one was
too small in rare cases (2 of 100 runs). However, having multiple
handlers for the same signal context can be considered deprecated
anyway. With the recommended Signal_handler wrapper for signal sessions,
you can't use this feature. Thus, we removed the multiple-handlers test.
Fixes#2450
The recently implemented capability resource trading scheme unfortunately
broke the automated capability memory upgrade mechanism needed by base-hw
kernel/core. This commit splits the capability memory upgrade mechanism
from the PD session ram_quota upgrade, and moves that functionality
into a separate Pd_session::Native_pd interface.
Ref #2398
We incorrectly used 'unsigned long' (which is 32 or 64 bit depending on
the CPU architecture) for a timestamp (which is always 64 bit) in the
timer-connection implementation.
Ref #2435
On platforms were we do not have local time interpolation we can simply
skip the first test stage in the timeout test. This way, we can at least
test the rest.
Fixes#2435
On ARM, we do not have a component-local hardware time-source. The ARM
performance counter has no reliable frequency as the ARM idle command
halts the counter. Thus, we do not do local time interpolation on ARM.
Except we're on the HW kernel. In this case we can read out the kernel
time instead.
Ref #2435
VM-exit interruption info was dropped and Vbox only needs guest CR3
value for guest-physical memory translation but does not actually change
it since the VM is running in unrestricted guest mode.
The explicit relative location of the file instructed both target builds
to generate ../main.o which gloriously fails with parallel builds. The
produced range of error messages was astonishing ranging from "file
truncated" to "TLS reference in ../main.o mismatches non-TLS reference
in ../main.o".
E.g., the script manually tried to configure lighttpd and used the old
porting directory structure that was integrated in the repos. For the
same reason it produced compile errors with noux packages.
Ref #2398
We do not have debug symbols in the bin/ binaries anymore. Thus, use the
debug/ binaries instead. We now have kernel specific binary names for
ld.lib.so and some others. Adapt, to this fact as well. For doing so
without unnecessary output, provide a new parameter "silent" at the
"kernel_specific_binary" procedure.
Ref #2398
A dataspace capability request to a ROM service may invalidate any
previously issued dataspace. Therefor no requests should be made while a
session dataspace is mapped. Reducing calls to the session also improves
performance where servicing a ROM request has a significant cost.
Fix#2418
There are programs, e.g. curl, that check if a connection was
established successfully by looking at SO_ERROR. Pretend that
the getsockopt() call was executed to keep them happy. If they
try to use a broken connection, the other socket functions will
bail.
This patch changes the noux build rules to produce a tar archive in
'bin/', alleviating the need for this step from the run scripts.
This way, the visible result of a built noux package is a single (tar)
file in '<build-dir>bin/', which is suited for the use as a ROM module.
The 'Stack_area_ram_session' is now a 'Stack_area_ram_allocator', which
simplifies the code and remove a dependency from the 'Ram_session'
interface, which we want to remove after all.
Issue #2407
By supplying a statically allocated initial block to the slab allocator
for signal contexts, we become able to construct a 'Signal_broker' (the
back end for the PD's signalling API) without any dynamic memory
allocation. This is a precondition for using the PD as meta-data
allocator for its contained signal broker (meta data allocations must
not happen before the PD construction is complete).
Issue #2407
If a child is allowed to constrain physical memory allocations but left
the 'phys_start' and 'phys_size' session arguments blank, init applies
builtin constraints for allocating DMA buffers.
The only component that makes use of the physical-memory constraint
feature is the platform driver. Since the built-in heuristics are
applied to the platform driver's environment RAM session, all
allocations performed by the platform driver satisfy the DMA
constraints.
To justify building-in these heuristics into init as opposed to
supplying the values as configuration arguments, the values differ
between 32 and 64 bit. The configuration approach would raise the need
to differentiate init configurations for both cases, which are
completely identical otherwise.
Issue #2407
This commit removes support for limitation of RAM allocations from the
platform_drv. A subsequent commit adds this feature to init.
Issue #2398
Issue #2407
By separating the session-interface concerns from the mechanics of the
dataspace creation, the code becomes simpler to follow, and the RAM
session can be more easily merged with the PD session in a subsequent
step.
Issue #2407
This patch allows core's 'Signal_transmitter' implementation to sidestep
the 'Env::Pd' interface and thereby adhere to a stricter layering within
core. The 'Signal_transmitter' now uses - on kernels that depend on it -
a dedicated (and fairly freestanding) RPC proxy mechanism for signal
deliver, instead of channeling signals through the 'Pd_session::submit'
RPC function.
With the capability-quota mechanism, the terminal-session won't always
be constructed completely on the first try (we may run out of caps in
the middle of the construction). Therefore, all members of the object
must be properly destructable. Furthermore, the patch replaces the
sliced heap by a heap to avoid allocating a new dataspace for each line
of the cell array.
Previously, the Genode::Timer::curr_time always used the
Timer_session::elapsed_ms RPC as back end. Now, Genode::Timer reads
this remote time only in a periodic fashion independently from the calls
to Genode::Timer::curr_time. If now one calls Genode::Timer::curr_time,
the function takes the last read remote time value and adapts it using
the timestamp difference since the remote-time read. The conversion
factor from timestamps to time is estimated on every remote-time read
using the last read remote-time value and the timestamp difference since
the last remote time read.
This commit also re-works the timeout test. The test now has two stages.
In the first stage, it tests fast polling of the
Genode::Timer::curr_time. This stage checks the error between locally
interpolated and timer-driver time as well as wether the locally
interpolated time is monotone and sufficiently homogeneous. In the
second stage several periodic and one-shot timeouts are scheduled at
once. This stage checks if the timeouts trigger sufficiently precise.
This commit adds the new Kernel::time syscall to base-hw. The syscall is
solely used by the Genode::Timer on base-hw as substitute for the
timestamp. This is because on ARM, the timestamp function uses the ARM
performance counter that stops counting when the WFI (wait for
interrupt) instruction is active. This instruction, however is used by
the base-hw idle contexts that get active when no user thread needs to
be scheduled. Thus, the ARM performance counter is not a good choice for
time interpolation and we use the kernel internal time instead.
With this commit, the timeout library becomes a basic library. That means
that it is linked against the LDSO which then provides it to the program it
serves. Furthermore, you can't use the timeout library anymore without the
LDSO because through the kernel-dependent LDSO make-files we can achieve a
kernel-dependent timeout implementation.
This commit introduces a structured Duration type that shall successively
replace the use of Microseconds, Milliseconds, and integer types for duration
values.
Open issues:
* The timeout test fails on Raspberry PI because of precision errors in the
first stage. However, this does not render the framework unusable in general
on the RPI but merely is an issue when speaking of microseconds precision.
* If we run on ARM with another Kernel than HW the timestamp speed may
continuously vary from almost 0 up to CPU speed. The Timer, however,
only uses interpolation if the timestamp speed remained stable (12.5%
tolerance) for at least 3 observation periods. Currently, one period is
100ms, so its 300ms. As long as this is not the case,
Timer_session::elapsed_ms is called instead.
Anyway, it might happen that the CPU load was stable for some time so
interpolation becomes active and now the timestamp speed drops. In the
worst case, we would now have 100ms of slowed down time. The bad thing
about it would be, that this also affects the timeout of the period.
Thus, it might "freeze" the local time for more than 100ms.
On the other hand, if the timestamp speed suddenly raises after some
stable time, interpolated time can get too fast. This would shorten the
period but nonetheless may result in drifting away into the far future.
Now we would have the problem that we can't deliver the real time
anymore until it has caught up because the output of Timer::curr_time
shall be monotone. So, effectively local time might "freeze" again for
more than 100ms.
It would be a solution to not use the Trace::timestamp on ARM w/o HW but
a function whose return value causes the Timer to never use
interpolation because of its stability policy.
Fixes#2400
This patch make sure that a once managed parent RPC object will always be
dissolved if an exception during the remaining child construction
occurs. The original version would miss the dissolve call if one of the
subsequent members throws an exception at construction time.
With this, we get rid of platform specific timer interfaces. The new
Timer class does the same as the old Clock class and has a generic
interface. The old Timer class was merely used by the old Clock class.
Also, we get rid of having only one timer instance which we tell with
each method call for which CPU it shall be done. Instead now each Cpu
object has its own Timer member that knows the CPU it works for.
Also, rename all "tics" to "ticks".
Fixes#2347
Removes the following Fiasco.OC specific features:
* GDB extensions for Fiasco.OC
* i.MX53 support for Fiasco.OC
* Kernel debugger terminal driver
* Obsolete interface Native_pd
* Obsolete function of interface Native_cpu
Previously we did write the SPSR via an MSR instruction without
additional flags. Unfortunately, this tells the CPU to write the
register only partially. This often isn't a problem as the users PSR
reset value normally is conform to our expectations but in some cases
(e.g. PSR endianess bit on WandBoard core #4) the reset value is bad.
Thus, we have to add the CXSF flags (access Control + eXtension + Status
+ Flags) so the CPU overwrites the entire register.
Fixes#2254
This patch eases the debugging of situations where a session-object
constructor wrongly throws an exception type not specified in the
'Local_service::Factory' interface.
This patch reduces the number of exception types by facilitating
globally defined exceptions for common usage patterns shared by most
services. In particular, RPC functions that demand a session-resource
upgrade not longer reflect this condition via a session-specific
exception but via the 'Out_of_ram' or 'Out_of_caps' types.
Furthermore, the 'Parent::Service_denied', 'Parent::Unavailable',
'Root::Invalid_args', 'Root::Unavailable', 'Service::Invalid_args',
'Service::Unavailable', and 'Local_service::Factory::Denied' types have
been replaced by the single 'Service_denied' exception type defined in
'session/session.h'.
This consolidation eases the error handling (there are fewer exceptions
to handle), alleviates the need to convert exceptions along the
session-creation call chain, and avoids possible aliasing problems
(catching the wrong type with the same name but living in a different
scope).
This patch mirrors the accounting and trading scheme that Genode employs
for physical memory to the accounting of capability allocations.
Capability quotas must now be explicitly assigned to subsystems by
specifying a 'caps=<amount>' attribute to init's start nodes.
Analogously to RAM quotas, cap quotas can be traded between clients and
servers as part of the session protocol. The capability budget of each
component is maintained by the component's corresponding PD session at
core.
At the current stage, the accounting is applied to RPC capabilities,
signal-context capabilities, and dataspace capabilities. Capabilities
that are dynamically allocated via core's CPU and TRACE service are not
yet covered. Also, the capabilities allocated by resource multiplexers
outside of core (like nitpicker) must be accounted by the respective
servers, which is not covered yet.
If a component runs out of capabilities, core's PD service prints a
warning to the log. To observe the consumption of capabilities per
component in detail, the PD service is equipped with a diagnostic
mode, which can be enabled via the 'diag' attribute in the target
node of init's routing rules. E.g., the following route enables the
diagnostic mode for the PD session of the "timer" component:
<default-route>
<service name="PD" unscoped_label="timer">
<parent diag="yes"/>
</service>
...
</default-route>
For subsystems based on a sub-init instance, init can be configured
to report the capability-quota information of its subsystems by
adding the attribute 'child_caps="yes"' to init's '<report>'
config node. Init's own capability quota can be reported by adding
the attribute 'init_caps="yes"'.
Fixes#2398
This patch reworks the implementation of core's RAM service to make use
of the 'Session_object' and to remove the distinction between the
"metadata" quota and the managed RAM quota. With the new implementation,
the session implicitly allocates its metadata from its own account. So
there is not need to handle 'Out_of_metadata' and 'Quota_exceeded' via
different exceptions. Instead, the new version solely uses the
'Out_of_ram' exception.
Furthermore, the 'Allocator::Out_of_memory' exception has become an alias
for 'Out_of_ram', which simplifies the error handling.
Issue #2398
The 'Session_object' unifies several aspects of server-component
implementations:
* It keeps track of session quotas and is equipped with standardized
interfaces (Quota_guard) to upgrade (and in the future potentially
downgrade) session quotas in a uniform way.
* It follows the pattern of modern RPC objects / signal handlers that
manage/dissolve themselves at the entrypoint given as constructor
argument. Thereby, the relationship with its entrypoint is always
coupled with the lifetime of the session-component object.
* It stores the session label, which was previously done manually by
most but not all server-component implementations.
* It stores the session 'diag' flag.
* It is equipped with output methods 'diag', 'error', and 'warning'.
All messages printed from the context of a session component is
automatically prefixed with the session type and client label.
Messages passed via 'diag' are only printed if the 'diag' flag of
the session is set.
Issue #2398
The 'diag' flag can be defined by a target node of a route in init's
configuration. It is propagated as session argument to the server, which
may evaluate the flag to enable diagnostic output for the corresponding
session.
Issue #2398
This patch makes use of the new 'Quota_transfer::Account' by the service
types in base/service.h and uses 'Quota_transfer' objects in
base/child.cc and init/server.cc.
Furthermore, it decouples the notion of an 'Async_service' from
'Child_service'. Init's 'Routed_service' is no longer a 'Child_service'
but is based on the new 'Async_service' instead.
With this patch in place, quota transfers do no longer implicitly use
'Ram_session_client' objects. So transfers can in principle originate
from component-local 'Ram_session_component' objects, e.g., as used by
noux. Therefore, this patch removes a strumbling block for turning noux
into a single threaded component in the future.
Issue #2398
The 'Quota_transfer' helper facilitated the implementation of quota
transfers between components in a transactional manner. It is designated
for framework-internal use (replacing the 'Transfer' class in child.h).
However, since it is also useful for init, we make it publicly
available.
The 'Quota_transfer::Account' class serves as an interface representing
the donor or receiver of quotas (parent, service, client).
Issue #2398
This patch replaces the 'Parent::Quota_exceeded',
'Service::Quota_exceeded', and 'Root::Quota_exceeded' exceptions
by the single 'Insufficient_ram_quota' exception type.
Furthermore, the 'Parent' interface distinguished now between
'Out_of_ram' (the child's RAM is exhausted) from
'Insufficient_ram_quota' (the child's RAM donation does not suffice to
establish the session).
This eliminates ambiguities and removes the need to convert exception
types along the path of the session creation.
Issue #2398
This patch adds sanity checks to the RPC entrypoint that detect attempts
to manage or dissolve the same RPC object twice. This is not always a
bug. I.e., if RPC objects are implemented in the modern way where the
object manages/dissolves itself. As the generic framework code (in
particular root/component.h) cannot rely on this pattern, it has to
call manage/dissolve for session objects anyway. For modern session
objects, this double attempt would result in a serious error (double
insertion into the object pool's AVL tree).
Issue #2398
This patch replaces the former use of size_t with the use of the
'Ram_quota' type to improve type safety (in particular to avoid
accidentally mixing up RAM quotas with cap quotas).
Issue #2398
The 'Ram_allocator' interface contains the subset of the RAM session
interface that is needed to satisfy the needs of the 'Heap' and
'Sliced_heap'. Its small size makes it ideal for intercepting memory
allocations as done by the new 'Constrained_ram_allocator' wrapper
class, which is meant to replace the existing 'base/allocator_guard.h'
and 'os/ram_session_guard.h'.
Issue #2398
This patch augments the existing session/session.h with useful types for
the session creation:
* The new 'Insufficient_ram_quota' and 'Insufficient_cap_quota'
exceptions are meant to supersede the old 'Quota_exceeded' exception
of the 'Parent' and 'Root' interfaces.
* The 'Session::Resources' struct subsumes the information about the
session quota provided by the client.
* The boolean 'Session::Diag' type will allow sessions to operate in a
diagnostic mode.
* The existing 'Session_label' is not also available under the alias
'Session::Label'.
* A few helper functions ease the extraction of typed session arguments
from the session-argument string.
Issue #2398
This patch upgrades the cap-space slab only if the kernel runs out of
entries, instead of consuming as much PD-session quota as possible.
Until now, the behavior worked well because the cap-space slab was the
only consumer of PD-session quota. However, once we start accounting all
PD session meta data - and eventually merging the PD and RAM services -
the aggressive scheme stands in the way.
Issue #2398
This accessor is useful to eagerly expand the slab with new slab blocks,
side stepping the slab's built-in policy for the allocation of new slab
blocks.
This is particularly important when using the slab for allocating the
cap space meta-data for the base-hw kernel. To guarantee that the slab
gets never exhausted in the kernel, it is expanded before entering the
kernel.
With the introduction of the 'Out_of_caps' exception type, the slab
needs to consider exceptions during the call of '_new_slab_block' by
reverting the 'nested' state.
The old download location is very shaky resp. currently unavailable and
also other projects (e.g., Gentoo and Linux From Scratch) use this
location. Note, the archive hash does _not_ change.
By building the posix library as shared object with an ABI, we
effectively decouple posix-using programs from the library
implementation (which happens to depend on several os-level APIs such as
the VFS).
This commit moves the headers residing in `repos/base/include/spec/*/drivers`
to `repos/base/include/drivers/defs` or repos/base/include/drivers/uart`
respectively. The first one contains definitions about board-specific MMIO
iand RAM addresses, or IRQ lines. While the latter contains device driver
code for UART devices. Those definitions are used by driver implementations
in `repos/base-hw`, `repos/os`, and `repos/dde-linux`, which now need to
include them more explicitely.
This work is a step in the direction of reducing 'SPEC' identifiers overall.
Ref #2403
causes the rem timer callback pending check to run more often (every 1 ms
instead 10 ms). This is essential to met the timeout requirements of the
audio backend, which must be checked&run every 5ms.
This patch adjusts the interactive scenarios of the gems repository to
use the depot. This has three immediate benefits. First, once the depot
is populated with binary archives, the start time of the scenarios
becomes very quick because most dependency checks and build steps are
side-stepped. Second, the run scripts become more versatile. In
particular, run scripts that were formerly supported on base-linux only
(nit_fader, decorator, menu_view) have become usable on all base
platforms that have a 'drivers_interactive' package defined. Finally,
the run scripts have become much shorter.
Issue #2339
In order to deliver base-hw as a binary archive, we need to install the
bootstap.o file to bin/. Since bin/ is a global name space shared by all
kernels, this patch renames the object file to bootstap-hw.o and thereby
clarifies the association of the file with base-hw.
This patch replaces the set-defaults command by a reset command, which
is needed to use the Lenovo x250 trackpoint. (original patch by
Christian Prochaska)
For asynchronously provided sessions, the parent has to maintain the
session state as long as the server hasn't explicitly responded to a
close request. For this reason, the lifetime of such session states is
bound to the server, not the client.
When the server responds to a close request, the session state gets
freed. The 'session_response' implementation does not immediately
destroy the session state but delegates the destruction to a client-side
callback, which thereby also notifies the client. However, the code did
not consider the case where the client has completely vanished at
session-response time. In this case, we need to drop the session state
immediately.
Fixes#2391
Originally, the spec files for less specific SPEC values were include
via the 'select_from_repositories' function. This implies that BASE_DIR
must always be present in the list of 'REPOSITORIES'. Otherwise the
spec files won't be found. By explicitly including sub specs from
'$(BASE_DIR)/mk', we lift this restriction.
This patch is required to build the OKL4 version of core from a source
archive. It avoids fetching source codes from BASE_DIR, and moves the
vpath wildcard for %.cc after all specific vpath definitins, in
particular those that are x86-specific. Without the latter change, core
would always end up using the generic version of 'platform_services.cc',
omitting the IO_PORT service from core.
The <build-dir>/bin/ directory used to contain symbolic links to the
unstripped build results. However, since the upcoming depot tool
extracts the content of binary archives from bin/, the resulting
archives would contain overly large unstripped binaries, which is
undesired. On the other hand, always stripping the build results is not
a good option either because we rely of symbol information during
debugging.
This patch changes the installation of build results such that a new
'debug/' directory is populated besides the existing 'bin/' directory.
The debug directory contains symbolic links to the unstripped build
results whereas the bin directory contains stripped binaries that are
palatable for packaging (depot tool) and for assembling boot images (run
tool).
By installing the core object to bin/, we follow the same convention as
for regular binaries. This, in turn, enables us to ship core in a
regular binary archive. The patch also adjusts the run tool to pick up
the core object from bin/ for the final linking stage.
When creating a source archive for the USB driver, both the contrib and
Genode-specific source codes are merged into a single directory
structure. In this case, the original way of determining the Linux
source code to scan for #include directives would apply the scanning to
Genode-specific source codes too. This patch tightens the search
criterion such that only Linux source codes are processed.
This macro is implicitly pulled in by libc-setjmp (via the libc's
cdefs.h). However, apparently not all sources include <setjmp.h>.
Unfortunately, for sources that do, this change produces a
double-definition warning. We should fix it by removing the dependency
from the libc's setjmp.
File_system servers shall deny clients not matching a defined policy.
Servers shall also apply session root offset policy followed by a client
offset.
Fix#2365
