The NIC router used to send an ICMP "Destination Unreachable" packet as
response to every unroutable IPv4 packet. However, RFC 1812 section 4.3.2.7
defines certain properties that must be fullfilled by an incoming packet in
order to be answered with this type of ICMP. One requirement is that the packet
is no IPv4 multicast.
This commit prevents sending the mentioned ICMP response for unroutable IPv4
multicasts and instead drops them silently.
Fixes#4563
The pci_decode has to extract the additional fields from the PCI configuration
space. The platform driver again has to parse and forward the knowledge too.
The PCI BAR indices are exported when info="yes" is set in the policy node for
the corresponding session.
Fixgenodelabs/genode#4577
The base address of I/O ports has a different encoding than
those of I/O memory. This needs to be encountered in the PCI
config helper utilities.
Fixgenodelabs/genode#4576
In overload situations, i.e. when a sender fills up the entire buffer, we land
in situations where the sender receives an ack_avail signal, releases one
packet, allocates and sends a packet and fails to allocate a second packet.
This is especially relevant if the receiver does not batch ack_avail signals
(such as vfs_lwip). In those ping-pong scheduling scenarios, the overhead from
catching the Packet_alloc_failed exception becomes significant. In case of the
NIC router, we will land in an overload situation if the sender is faster than
the receiver. The packet buffer will be filled up at some point and the NIC
router starts to drop packets. For every dropped packet, we currently have to
catch the Packet_alloc_failed exception.
This commit adds a new method alloc_packet_attempt to Packet_stream_source that
has almost the same signature as the older alloc_packet method but returns
an Attempt<Packet_descriptor, Alloc_packet_error> object. As the method already
used the allocator back end exception-less, changes on lower levels were not
needed. Furthermore, the NIC router was modified to use the new exception-less
alloc_packet_attempt instead of alloc_packet.
Ref #4555
The checksums for forwarded/routed UDP, TCP and ICMP, used to be always
re-calculated from scratch in the NIC router although the router changes only
a few packet fields. This commit replaces the old approach whereever sensible
with an algorithm for incremental checksum updates suggested in RFC 1071.
The goal is to improve router performance.
Ref #4555
The checksums for forwarded/routed IPv4, used to be always re-calculated from
scratch in the NIC router although the router changes only a few packet fields.
This commit replaces the old approach whereever sensible with an algorithm for
incremental checksum updates suggested in RFC 1071. The goal is to improve
router performance.
Ref #4555
Prevent public reflection of the only internally used 'init_sum' argument in
'uint16_t internet_checksum(...)' that, in addition, added a default value to
the function interface.
Ref #4555
The wakeup call only emits a single signal as it assumed both are
handled by the same signal handler. However, the original implementation
did not reset the wakeup_needed variable properly.
genodelabs/genode#4555
When using signal batching, ack_avail and packet_avail should always
be emitted and preferred over ready_to_submit and ready_to_ack.
A signal receiver might decide to not register the ready_to_* signals when it
handles congestion by dropping packets. The Nic router is an example of
such a signal receiver.
genodelabs/genode#4555
Using the 'query_buffer_ppgtt()' function allows for retrieving the
virtual address of the buffer in the PPGTT.
This is for components that manage the GPU virtual addresses rather than
the client as is the case with the lima driver.
Issue #4559.
As accommodating the session component object is already taken care of
be the root component implementation, remove the remaining redundant
checks.
Fixes#4521.
There is a race between the trace subject doing the buffer
initialization and the monitor trying to iterate the buffer entries. If
the monitor tries to iterate entries of an uninitialized buffer, it will
read the very first entry twice. The monitor should therefore only start
iteration when the buffer has been initialised.
genodelabs/genode#4513
* Adds methods for copying raw data to the data field of Ethernet frames and
UDP packets. This is used in the port to wrap the higher-layer packet data
prepared by the contrib code with the additionally required headers before
sending it at a network session.
* Adds a method to cast raw data to an IPv4 packet. This is required in the
port in order to check values in stand-alone IP packets produced by the
contrib code before sending them at a network session.
* Adds methods for setting UDP ports given big endian port values without
having to convert to little endian in the app and then back to big endian in
the net lib.
Ref #4397
Instead of returning an invalid device capability when a device
is (not yet) available, e.g. a PCI device is requested before the
PCI bus got parsed accordingly, we check the device capability
within the Platform::Connection utilities, and register temporarily
an Io_signal_handler to wait for changes of the devices ROM, and
try the device aquisition again. Thereby, simple drivers so not have
to take the burden to do so.
To enable this feature for all drivers, we always have to export a
devices ROM, but limit the information about physical resources
(I/O memory addresses, IRQ numbers, I/O port ranges) to clients with
'info=yes' in their policy description.
Fixgenodelabs/genode#4496
To discharge the generic platform driver from certain PCI bus scanning,
and ACPI + kernel specifics, this commit introduces a new component,
which consumes the acpi drivers report and the platform_info from core
to prepare a devices ROM for the platform driver that contains all
PCI devices and its resources.
Fixgenodelabs/genode#4495
To signal that a device gets used and released by a session
introduce claim, release, and release all callbacks in the
USB interface of the C-API.
Ref genodelabs/genode#4483
This patch changes the meaning of the 'offset' parameter of the
'produce_write_content' and 'consume_read_result' hook functions.
The value used to reflect the absolute byte position but in practice,
a job-relative byte offset is desired.
Issue #4474
This patch reduces repetitive log output by omitting inactive trace
subjects from the log output. The information about all subjects can
still be dumped by setting 'verbose="yes"'.
Issue #4448
The utilities of the new util/formatted_output.h header complement the
existing base/output.h with the text-formatting support needed to
produce tabular output.
Fixes#4449
This commit adjusts the value such that USB sessions requested by
VirtualBox6 on Sculpt OS can get established on the first try without
invoking the session-retry mechanism. This reduces the number of
diagnostic log messages like:
Error: Insufficient 'ram_quota',got 6296372 need 6297928
Split the trace buffer into two partitions in order to prevent overwriting
of entries when the consumer is too slow. See file comment in buffer.h.
genodelabs/genode#4434
This commit simplifies the current implementation by overloading the
length field with a padding indicator in addition to the zero-length
head entry. This simplifies the iteration semantics as it eliminates
the need for determining whether a zero-length entries is the actual
head of the buffer or a padding at the buffer end.
genodelabs/genode#4434
* Unifies the declaration of callbacks which manage driver/client
shared dataspaces
* Move the Linux driver-specific callback implementation to the
lx_emul library from the PC's USB host driver
Fixgenodelabs/genode#4439
The new usb_host driver for PC by default needs more RAM quota in contrast
to the old one. To minor warnings and repeated attempts to open a USB
session from a client, this commit increases the default RAM quota by one
page.
Ref genodelabs/genode#4416
Adds a function to the USB part of the Genode's C API, to enable
usb_host drivers to acknowledge USB request in client's packet buffer
although they are not assigned to an USB device. The requests are
marked with a "no device" error.
This commit fixes a regression originally solved in genodelabs/genode#4149
Ref genodelabs/genode#4416
XML allows attribute values like <node attr="\"/>. The XML parser
wrongly reflects this case as 'Invalid_syntax'. This behavior stems from
the implicit use of the 'end_of_quote' function, which considers the
sequence of '\"' as a quoted '"' rather than the end of a quoted string.
The patch solves this problem by making the 'end_of_quote' part of
the tokenizer's scanner policy.
The patch removes the 'end_of_quote' function from 'util/string.h'
because it is not universal, and to avoid the ambiguity with
'SCANNER_POLICY::end_of_quote'.
Fixes#4431
The Single_file_system now forwards the
`File_io_service::notify_read_ready` method to the
handle as it already did for most of the other methods.
genodelabs/genode#4394
'generate(Xml_node node)', as used by the Sculpt manager, calls this
function instead of the lambda version. The 'report' function of the
'Genode::Reporter' does not throw an exception in case there is not
enough backing storage for the 'generate' request. Therefore, we have to
check this condition in a loop and call '_increase_report_buffer' in
case size limits are reached.
Patch by Norman Feske.
issue #4369
Clang really doesn't like char subscripts. I can't say I blame it. Fix
the warning by an explicit cast to unsigned.
include/nitpicker_gfx/tff_font.h:230:53: error:
array subscript is of type 'char' [-Werror,-Wchar-subscripts]
Tff::Vertical_metrics const m = _vertical_metrics['m'];
^~~~
Issue #4421
Clang likes to complain when lambdas capture parameters without
actually using them. This patch fixes a couple of such problems in VFS
related os module code.
Issue #4421
If the buffer contains padding at the end, the iteration must continue
in order to restart iteration from the start of the buffer.
genodelabs/genode#4244
This patch makes the server-side policy-matching logic available outside
the 'Session_policy' class. Given that the new 'with_matching_policy'
function does not throw any exception, it gives server implementations
the freedom to avoid the C++ exception mechanism for the policy handling.
If the platform driver lacks the 'managing_system="yes"' attribute,
requests for DMA addresses return 0. This patch is meant to help
diagnosing such configuration issues.
Issue #2243
The new event type allows for the propagation of sequence numbers as a means to
validate the freshness of input handling. E.g., an menu-view-based application
can augment artificial sequence numbers to the stream of motion events supplied
to 'menu_view'. Menu view, in turn, can now report the latest received sequence
number in its hover reports, thereby enabling the application to robustly
correlate hover results with click positions.
Issue #4398
The 'read' and 'write' utilities are from a time before the VFS API
as os/vfs.h was available. They rely on the (now removed) blocking
semantics of the packet-stream interface.
The only remaining legitimate use case of the direct interaction with
the file-system session without VFS is the back end of gcov, which needs
a way to exfiltrate the statistical data using a channel that is
independent from the libc or the VFS.
Issue #4390
Add 'export_buffer'/'import_buffer' calls in order to support buffer
sharing between GPU sessions.
Reduce CAP costs for Gpu::Connection from 256 to 32.
issue #4380
Override 'try_alloc/free' because ethernet frame headers are 14 bytes
(src/dst mac (12) + ethertype (2)) causing the IP header to be 2 byte
aligned, leading to problems on platforms that require load/store
operations to be naturally aligned when reading, for example, 4 byte IP
addresses. Therefore, we align the allocation to 2 bytes, so the IP
header is aligned to 4.
issue #4312
The key changes in this patch are:
* Buffer allocation is moved into a separate Buffer_pool helper. The
implementation of the buffer allocation strategy does not change.
The helper allocates a single RAM dataspace and splits it in multiple,
equally sized chunks.
* Management of main descriptor ring is enacapsulated in Descriptor_ring
helper class.
* Use separate RAM dataspaces for descriptor rings and buffers.
Previously both of them were packed into a single dataspace. This
might have been more RAM efficient, but IMO it made the code uglier and
harder to understand.
* All of the VirtIO::Queue members are now initialized on the class member
initializer list. This is possible due to previously listed changes.
* Since all VirtIO::Queue members are initalized on member initalizer
list, some additional ones can be marked as const, ex _avail, _used ring
pointers.
* Move descriptor writing code into a common method used by both
write_data and write_data_read_reply members. This avoids some code
duplication between those methods.
* Get rid of request_irq argument that most public VirtIO::Queue methods
accept. None of the existing drivers use it and I doubt this will
change any time soon.
* Use Genode namespace by default in Virtio.
This patch also fixes at least one bug that I discovered while working
on VirtIO block device driver. Namely, when chaining descriptors only the
first descriptor in the chain should be exposed in the available ring.
Issue #4347
The const-variant of the data() method contained an erroneous
calculation of the tail size. This led to the size guard throwing
exceptions when trying to parse TCP packets that only contained the
TCP header.
Fixesgenodelabs/genode#4340
Thanks to Piotr Tworek for the fix and his explanation as follows:
The basic idea is to try to fit payload data into the descriptor used to
send the header. If there is no payload, or the payload fits exactly
into the remaining space in the header decriptor, len should be 0 and
only one descriptor should be used. In such case the "next" and "flags"
members of the descriptor structure should be set to 0.
In case there is some extra payload data to send, but its size is
bigger than the remaining free space in the descriptor used to send the
header, len should contain the remaining size of the payload that
can't be sent via the header descriptor. The code will then chain
additional descriptors to handle this remainder.
With the len variable shadowing, the code will never queue the remaining
data.
Issue #4327
Some more advanced devices like VirtIO GPU do expect they can receive
responses to VirtIO commands they issue via VirtIO queue. Such responses
are not sent via a separate device writeable queue. Instead the driver
is expected to queue some additional descriptors and buffers which the
device can then use to provide the reply.
This patch adds support for such write-data-read-response opeartion to
Genode VirtIO::Queue implementation. The implementation is pretty simple
and does not support any fancy features like receiving the response
asynchronously. Instead the operation will use caller provided callback
to wait for the device to process the command. Once this callback
returns the write-data-read-response VirtIO::Queue function will invoke
another callback passing received response as argument.
Mesa queries information about the underlying device and this header
denotes the layout of the information. It is also used by the driver
itself to populate the 'info_dataspace'.
Issue #4329.
This patch changes the 'Allocator' interface to the use of 'Attempt'
return values instead of using exceptions for propagating errors.
To largely uphold compatibility with components using the original
exception-based interface - in particluar use cases where an 'Allocator'
is passed to the 'new' operator - the traditional 'alloc' is still
supported. But it existes merely as a wrapper around the new
'try_alloc'.
Issue #4324
The new interfaces are meant to gradually replace the existing
Gpio_session interface.
- Each session refers to a single pin.
- The session types distiguish the direction of the signal as input or
output.
- Pin coordinates can be selected via session labels.
- GPIO interrupts are covered by the regular IRQ session interface.
The interfaces are accompanied by framework utilities and interfaces:
- os/pin_driver.h
- pin_control_session/component.h
- pin_state_session/component.h
These headers relieve GPIO drivers from implementing boilerplate code by
providing device-agnostic portions. The A64 pio driver serves as
reference for using those utilities.
https://github.com/nfeske/genode-allwinner/tree/master/src/drivers/pin/a64Fixes#4315
Allocating and mapping buffers not only consumes RAM quota, it consumes
CAP quota as well. Extended the Gpu session to allow for dealing with
that on the client side.
On a side note, the amount of initial CAP quota needed to establish
a connection is increased to cover the current costs of the Intel
GPU multiplexer.
Issue #4284.
This patch introduces a C API to be used by input drivers to generate
Genode events. The initial version is limited to multitouch events only.
Fixes#4273
The former implementation did not internally track ROM changes notified
vs. delivered to the client. We adapt the versioning implementation
implemented in dynamic_rom_session.h and enable explicit notification of
the current version.
The feature is used by the clipboard to notify permitted readers of the
clipboard ROM service on focus change via the newly created private
Rom::Module::_notify_permitted_readers() function.
Fixes#4274
The various mapping methods are modelled after the requirements of
the Intel GPUs or rather the Mesa driver back end.
With upcoming support for other driver back ends, we need to
sequeeze their requirements in as well. For now hijack 'map_buffer'
to provide for specifying the kind of attributes the client needs.
For now all buffers mapped in the GGTT for Intel GPUs are treated
as RW.
Issue #4265.
This call allows for checking if the given execution buffer has been
completed and complements the completion signal. Initially the GPU
multiplexer always sent such a signal when the currently scheduled
execution buffer has been completed. During enablement of the 'iris'
driver it became necessary to properly check of sequence number.
In case of the Intel GPU multiplexer the sequence numbers are
continous, which prompted the greater-than-or-equal check in the
DRM back end. By hidding this implementation detail behind the
interface, GPU drivers are free to deal with sequence numbers any
way they like and allows for polling in the client, where the
completion signal is now more of a progress signal.
Issue #4265.
The current info implementation (as RPC) is limited in a few ways:
* The amount of data that may be transferred is constrained by the
underlying base platform
* Most information never changes during run time but is copied
nonetheless
* The information differs depending on the used GPU device and
in its current implementation only contains Intel GPU specific
details
With this commit the 'info' RPC call is replaced with the
'info_dataspace' call that transfers the capability for the dataspace
containing the information only. This is complemented by a client
local 'attached_info' call that allows for getting typed access to
the information. The layout of the information is moved to its own
and GPU-specific header file, e.g., 'gpu/info_intel.h'
Issue #4265.
Rather than using the dataspace capability directly, let the client
choose its own local identifier that is linked to the underlying
capability.
Fixes#4265.
The contents of those descriptor rings can be modified by the device.
Mark them as volatile so the compiler does not make any assumptions
about them.
Issue #4264
Both, trace_logger and vfs_trace had their own trace_buffer.h. This
commit consolidates the existing implementations and provides the
resulting trace_buffer.h at 'include/trace/'. It thereby becomes part of
the trace api archive.
genodelabs/genode#4244
With this commit, the NIC router DHCP client reads out the first DNS domain
name (DHCP option 15) if any from a DHCP reply that generates an IPv4 config
for a domain and stores the name together with the IPv4 config for that domain.
DNS domain names are reported via the new report tag '<dns-domain>' if the
'config' attribute in the config tag '<report>' is set.
Furthermore, the NIC router DHCP server becomes able to obtain a DNS domain
name from another domain that has a DHCP client dynamically (given the config
attribute 'dns_config_from' is set and no static DNS config is given) or
statically from its configuration (new config tag '<dns-domain>') and propagate
this name with DHCP replies (DHCP option 15).
The 'nic_router_dhcp_*' tests are adapted to test the new feautures.
The commit also gets rid of some mirrored files in
'test/nic_router_dhcp/manager'.
Fixes#4246
The NIC router DHCP server used to add an extra option 6 field to DHCP replies
for each DNS server address. This conflicts with RFC #2132 section 3.8 which
states that the addresses should be listed within one option 6 field without
delimiter. The discrepancy is fixed by this commit.
Ref #4242
The former declaration of the IPv4 packet did not only use the questionable
tool of implementation-defined C++ bitsets but also lacked access to flags
"don't fragment" (DF) and "more fragments" (MF). This commit replaces the
C++ bitsets by using the register framework and introduces accessors for the
missing flags.
Ref #4236
This commit introduces a C-API to the Uplink session, as well as to
serve as a Block service. It can be used by drivers ported from
C-only projects, like the Linux kernel, or BSD kernels for instance.
Fix#4226
Adapts Dir_file_system::open_composite_dirs in a way that it returns "success"
when the leaf node of the path is an empty directory but "lookup failed", as
usual, if one of the other directories on the way to the leaf node is empty.
I couldn't find a technical reason why we used to return "lookup failed" when
only the leaf node was empty.
The commit also adds a test for en empty root directory and empty
sub-directories to the fs_query run script.
Fixes#4198
Introduces the notion of a transaction that consists of one or more
messages. Whereby a message has a read or write direction and consists
of one or more bytes.
Issue #4170Fixes#4169
This patch moves the utility from the app/text_area to os/vfs.h to make
it easier to use by other components. By hosting the 'New_file' as a
friend alongside the 'Directory', we can now pass a 'Directory' as
constructor argument, which is consistent with other utilities such as
'File_content'.
As a further improvement, the new version supports the implicit creation
of the directory hierarchy leading to the new file.
Issue #4032
For fs_file_systems, reads are limited to the size of the packets from the
File_system session. Hence, we cannot read the large files in one go.
This fix is particularly helpful for fonts_fs, as it enables including font
files from a File_system.
genodelabs/genode#4135
With the update to GCC 10, the compiler stopped with an error when compiling
places where a MAC address is copied from outside into a packed object using
the Net::Netaddress::copy method (e.g. in
Net::Arp_packet::dst_mac(Mac_address)):
! error: writing 6 bytes into a region of size 4 [-Werror=stringop-overflow=]
While trying to find a clean solution for this error, I found posts on
gcc.gnu.org and github that stated that the size calculations that cause these
errors are incorrect. Indeed, I could verify that the actual size of the two
regions was static and exactly the same in places were the error occured.
Furthermore, I couldn't find a way of making it more clear to the compiler
that the sizes are the same. By accident, we found that using the address of
the first element of the array that forms the second region instead of the
array address itself, somehow circumvents the error.
Fixes#4109
With the update to GCC 10 the compiler used to warn when using the internet
checksum functions on packet classes (like in
Net::Ipv4_packet::update_checksum):
warning: converting a packed ‘Net::[PACKET_CLASS]’ pointer
(alignment 1) to a ‘const uint16_t’ {aka ‘const short
unsigned int’} pointer (alignment 2) may result in an
unaligned pointer value
Apparently, the 'packed' attribute normally used on packet classes sets the
alignment of the packet class to 1. However, for the purpose of the
internet-checksum functions, we can assume that the packet data has no
alignment. This is expressed by casting the packet-object pointer to a pointer
of the new packed helper struct 'Packed_uint16' that contains only a single
uint16_t member before handing it over to the checksum function (instead of
casting it to a uint16_t pointer).
Ref #4109
Introduce a new _overflowed state variable to indicate whether the
horizontal boundary was reached already and to omit subsequent character
output.
This state is necessary to maintain a valid cursor position at all
times. The _overflowed attribute is reset once the cursor is moved into
a valid position again.
To harmonise the bounds checking for _cursor_pos modifications, the
`constrain()` method was added.
Fixesgenodelabs/genode#4093
Also fixes a bug in `vpa()` and `vpb()` which moved the cursor
horizontally instead of vertically.
* The device XML information dataspace is only provided,
when the client's policy states `info="yes"`
* The device XM information gets changed to include the
physical resource names (I/O memory and IRQ addresses)
instead of virtual ids and page offset
Fix#4077
This is a follow-up fix for "Streamline platform-device API on ARM".
There is an ambiguity of the 'local_addr' method between the inherited
'Attached_dataspace' and the local declaration, which results in the
double application of the sub-page Range::start.
Issue #4075
This API rework eases the access to memory-mapped I/O registers and
interrupts when using the platform driver. It introduces the notions of
- Platform::Device - one device obtained from a platform session
- Platform::Device::Mmio - locally-mapped MMIO registers of a device
- Platform::Device::Irq - interface for receiving device interrupts
The patch touches several drivers. Some drivers would require a
significant structural change to adopt the new API (e.g., net/virtio,
dde_linux drivers, imx gpio). In these cases, the patch adds
compatibility shims meant to be temporary. In other cases (e.g., imx
i2c), the adaptation was simple enough to carry through.
Fixes#4075
This patch extends the 'Platform_session::alloc_dma_buffer' interface
with a 'Cache' argument that corresponds to the argument accepted by
'Ram_allocator::alloc', which is used by the platform driver under the
hood.
Since the x86 platform driver used to be hardwired to allocate DMA
buffers as UNCACHED, I adjusted all drivers by specifying the UNCACHED
argument. Right now, this is needed as a hint for core to steer the
allocation of I/O page tables. Once we eliminate the need for such hints
(by introducing an explicit 'Region_map::attach_dma' operation), we can
revisit the drivers individually because cached DMA buffers should
generally be fine on the x86 architecture.
Issue #2243
This change avoids many repetetive Genode:: prefixes, making the code
easier to read. The patch also includes a few consistency fixes
regarding include guards and file headers. It also renames
Platform_device::String to Platform_device::Device:name.
Issue #2243
This patch adds the designated alternative to Dataspace::phys_addr to
the platform-session interface. Under the hood, the platform driver
still calls Dataspace::phys_addr but it should eventuelly become the
only caller before we can abolish this function.
Issue #2243
This patch changes the 'alloc_aligned' interface as follows:
- The former 'from' and 'to' arguments are replaced by a single
'range' argument.
- The distinction of the use cases of regular allocations vs.
address-constrained allocations is now overed by a dedicated
overload instead of relying on a default argument.
- The 'align' argument has been changed from 'int' to 'unsigned'
to be better compatible with 'addr_t' and 'size_t'.
Fixes#4067
The vfs pipe plugin can now be used as named pipe which anables data
transfer via file handles from one component to another. E.g. if one
would like to send data from component A to stdin of a libc component B,
one can do so by simply writing to that fifo file.
Issue #3583
* Update the 'packet_size' information with the actual length for
each isoc frame to be able to handle short reads at the client side.
* Copy the whole transfer buffer because the host controller stores
the data at the original offsets, i.e., the buffer is not densely
packed.
Fixes#4018.
Adds new Uplink session interface, the corresponding client side (Client,
Connection), and the corresponding API archives. An Uplink session is almost
the same as a NIC session with the difference that the roles of the end points
are swapped. An Uplink client is the one that provides a network interface
(for instance, a NIC driver) whereas an Uplink server is the one that uses
that network interface (for instance, a networking stack).
Therefore, in contrast to the NIC session, MAC address and link state come from
the Uplink client. The link state is reflected through the lifetime of an
Uplink session: The client requests the session only when the link state is
"UP" and closes it whenever the link state becomes "DOWN" again. The MAC
address is transmitted from the Uplink client to the Uplink server as an
argument of the session request.
Ref #3961
This commit restores the diag feature for selecting diagnostic output of
services provided by core. This feature became unavailable with commit
"base: remove dependency from deprecated APIs", which hard-wired the
diag flag for core services to false.
To control this feature, three possible policies can be expressed in a
routing target of init's configuration:
* Forcing silence by specifying 'diag="no"'
* Enabling diagnostics by specifying 'diag="yes"'
* Forwarding the preference of the client by omitting the 'diag'
attribute
Fixes#3962
- Vendor devices add addtional data to the config descriptor, read and
added to the usb session
- allow '0' configuration within the usb session
issue #3822
To simplify writing native VirtIO drivers for Genode add helper classes
representing VirtIO device and queue. The queue implementation should
be platform independant. The device abstraction however is closely tied
to the VirtIO transport being used (PCI/MMIO). Both PCI and MMIO
implementations expose the same public API so the actual driver logic
should be the same regardless of which transport is used.
Its also important to note that the PCI version of Virtio::Device
currently does not support MSI-X interrupts. Unfortunately my kowledge
about PCI bus is very limited and my main area of interest was to get
VirtIO drivers working on virt_qemu ARM/Aarch64 platform. As such all
the VirtIO drivers I plan to submit will work with PCI bus, but might
not use some extended capabilities.
Ref #3825
- make GPIO server more robust on imx by not throwing exceptions for
unknown pins, use '_with_gpio' instead
- use 'Gpio::Pin' data type instead of POD 'unsigned'
issue #3900
The combination of Net::Mac_address and
Genode::ascii_to(Net::Mac_address) required shaky quirks in several
places because GCC is not able to resolve the ascii_to overload if
base/xml_node.h was included to early. The current solution moves the
several ascii_to overloads "closer" to the Net types by putting them
into the Net namespace, where GCC reliably picks them up.
Hence, co-locating the ascii_to() utility with the overload type in the
same scope/namespace is good practice.
This patch removes the now obsolete <nic/xml_node.h> header file.
- base/cancelable_lock.h becomes base/lock.h
- all members become private within base/lock.h
- solely Mutex and Blockade are friends to use base/lock.h
Fixes#3819
Until now, Genode's framebuffer session interface was based on the
RGB565 pixel format. This patch changes the pixel format to 32-bit
XRGB where the X part is ignored. It adapts all graphical applications
and device drivers accordingly.
The patch also adjusts the users of the drivers_interactive packages,
assigning 64 MiB RAM and 1500 caps to the drivers subsystem, which is
sufficient for covering high resolutions at 32 bits per pixel and to
accommodate multi-component USB HID input stacks.
Fixes#3784
