mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-26 00:41:17 +00:00
c30220d458
Cell C RTL30VW is a LTE router with tho gigabit ethernets and integrated QMI mPCIE modem. This is stripped version of ASKEY RTL0030VW. Hardware: Specification: -CPU: IPQ4019 -RAM: 256MB -Flash: NAND 128MB + NOR 16MB -WiFi: Integrated bgn/ac -LTE: mPCIe card (Modem chipset MDM9230) -LAN: 2 Gigabit Ports -USB: 2x USB2.0 -Serial console: RJ-45 115200 8n1 -Unsupported VoIP Known issues: None so far. Instruction install: There are two methods: Factory web-gui and serial + tftp. Web-gui: 1. Apply factory image via stock web-gui. Serial + initramfs: 1. Rename OpenWrt initramfs image to "image" 2. Connect serial console (115200,8n1) 3. Set IP to different than 192.168.1.11, but 24 bit mask, eg. 192.168.1.4. 4. U-Boot commands: sf probe && sf read 0x80000000 0x180000 0x10000 setenv serverip 192.168.1.4 set fdt_high 0x85000000 tftpboot 0x84000000 image bootm 0x84000000 5. Install sysupgrade image via "sysupgrade -n" Back to stock: All is needed is swap 0x4c byte in mtd8 from 0 to 1 or 1 to 0, do firstboot and factory reset with OFW: 1. read mtd8: dd if=/dev/mtd8 of=/tmp/mtd8 2. go to tmp: cd /tmp/ 3. write first part of partition: dd if=mtd8 of=mtd8.new bs=1 count=76 4. check which layout uses bootloader: cat /proc/mtd 5a. If first are kernel_1 and rootfs_1 write 0: echo -n -e '\x00' >> mtd8.new 5b. If first are kernel and rootfs write 1: echo -n -e '\x01' >> mtd8.new 6. fill with rest of data: dd if=mtd8 bs=1 skip=77 >> mtd8.new 7. CHECK IF mtd8.new HAVE CHANGED ONLY ONE BYTE! e.g with: hexdump mtd8.new 8. write new mtd8 to flash: mtd write mtd8.new /dev/mtd8 9. do firstboot 10.reboot 11. Do back to factory defaults in OFW GUI. Based on work: Cezary Jackiewicz <cezary@eko.one.pl> Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com> |
||
|---|---|---|
| .. | ||
| 039-crypto-qce-add-CRYPTO_ALG_KERN_DRIVER_ONLY-flag.patch | ||
| 040-crypto-qce-switch-to-skcipher-API.patch | ||
| 041-crypto-qce-fix-ctr-aes-qce-block-chunk-sizes.patch | ||
| 042-crypto-qce-fix-xts-aes-qce-key-sizes.patch | ||
| 043-crypto-qce-save-a-sg-table-slot-for-result-buf.patch | ||
| 044-crypto-qce-update-the-skcipher-IV.patch | ||
| 046-crypto-qce-initialize-fallback-only-for-AES.patch | ||
| 047-crypto-qce-use-cryptlen-when-adding-extra-sgl.patch | ||
| 048-crypto-qce-use-AES-fallback-for-small-requests.patch | ||
| 049-crypto-qce-handle-AES-XTS-cases-that-qce-fails.patch | ||
| 051-crypto-qce-allow-building-only-hashes-ciphers.patch | ||
| 070-v4.20-soc-qcom-spm-add-SCM-probe-dependency.patch | ||
| 071-01-v4.20-ARM-dts-qcom-ipq4019-use-v2-of-the-kpss-bringup-mech.patch | ||
| 071-02-ipq40xx-Fix-booting-secondary-cores.patch | ||
| 072-v4.20-ARM-dts-qcom-ipq4019-add-cpu-operating-points-for-cp.patch | ||
| 074-ARM-qcom-Add-IPQ4019-SoC-support.patch | ||
| 075-dt-bindings-phy-qcom-ipq4019-usb-add-binding-documen.patch | ||
| 076-phy-qcom-ipq4019-usb-add-driver-for-QCOM-IPQ4019.patch | ||
| 077-qcom-ipq4019-add-USB-devicetree-nodes.patch | ||
| 080-ARM-dts-qcom-add-gpio-ranges-property.patch | ||
| 081-clk-fix-apss-cpu-overclocking.patch | ||
| 086-ipq40xx-fix-high-resolution-timer.patch | ||
| 088-v5.6-regulator-add-IPQ4019-SDHCI-VQMMC-LDO-driver.patch | ||
| 089-v5.5-ARM-dts-qcom-ipq4019-Add-SDHCI-controller-node.patch | ||
| 100-arm-dts-IPQ4019-add-SDHCI-VQMMC-LDO-node.patch | ||
| 303-spi-nor-enable-4B-opcodes-for-mx25l25635f.patch | ||
| 304-mtd-spi-nor-Add-support-for-mx25r3235f.patch | ||
| 400-mmc-sdhci-sdhci-msm-use-sdhci_set_clock-instead-of-s.patch | ||
| 700-net-add-qualcomm-mdio.patch | ||
| 701-dts-ipq4019-add-mdio-node.patch | ||
| 702-dts-ipq4019-add-PHY-switch-nodes.patch | ||
| 703-net-IPQ4019-needs-rfs-vlan_tag-callbacks-in.patch | ||
| 705-net-add-qualcomm-ar40xx-phy.patch | ||
| 706-ar40xx-abort-probe-on-missig-phy.patch | ||
| 710-net-add-qualcomm-essedma-ethernet-driver.patch | ||
| 711-dts-ipq4019-add-ethernet-essedma-node.patch | ||
| 712-mr33-essedma.patch | ||
| 713-essedma-alloc-skb-ip-align.patch | ||
| 714-essedma-add-fix-for-memory-allocation.patch | ||
| 850-soc-add-qualcomm-syscon.patch | ||
| 900-dts-ipq4019-ap-dk01.1.patch | ||
| 901-arm-boot-add-dts-files.patch | ||
| 997-device_tree_cmdline.patch | ||