mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-22 23:12:32 +00:00
71a6f45fdf
The Netgear EVG2000 is a wifi gigabit router, 2.4 GHz single band with two internal antennas integrated in the main PCB. Hardware: - SoC: Broadcom BCM6369 - CPU: dual core BMIPS4350 V3.1 @400Mhz - RAM: 64 MB DDR - Flash: 16 MB parallel NOR - LAN switch: Broadcom BCM53115, 5x 1Gbit - Wifi 2.4 GHz: Broadcom BCM4322 802.11bgn - USB: 2x 2.0 - Buttons: 2x, 1 reset - LEDs: 10x - FXS: 2x - UART: yes Installation via CFE web UI: 1. Power off the router and make a temporal TX-RX shortcircuit on the serial pins. 2. Power on the router and wait 3 or more seconds 3. Remove the TX-RX shortcircuit 4. Browse to http://192.168.1.1 or http://192.168.0.1 and upload the firmware 5. Wait a few minutes for it to finish Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
238 lines
3.4 KiB
Plaintext
238 lines
3.4 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-or-later
|
|
|
|
#include "bcm6368.dtsi"
|
|
|
|
/ {
|
|
model = "Netgear EVG2000";
|
|
compatible = "netgear,evg2000", "brcm,bcm6369", "brcm,bcm6368";
|
|
|
|
aliases {
|
|
led-boot = &led_power_green;
|
|
led-failsafe = &led_power_red;
|
|
led-running = &led_power_green;
|
|
led-upgrade = &led_power_green;
|
|
};
|
|
|
|
keys {
|
|
compatible = "gpio-keys-polled";
|
|
poll-interval = <100>;
|
|
|
|
reset {
|
|
label = "reset";
|
|
gpios = <&gpio 25 GPIO_ACTIVE_LOW>;
|
|
linux,code = <KEY_RESTART>;
|
|
debounce-interval = <60>;
|
|
};
|
|
|
|
wps {
|
|
label = "wps";
|
|
gpios = <&gpio 26 GPIO_ACTIVE_LOW>;
|
|
linux,code = <KEY_WPS_BUTTON>;
|
|
debounce-interval = <60>;
|
|
};
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
|
|
led@2 {
|
|
label = "green:voip2";
|
|
gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
led@4 {
|
|
label = "red:internet";
|
|
gpios = <&gpio 4 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
led@5 {
|
|
label = "green:internet";
|
|
gpios = <&gpio 5 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
led@14 {
|
|
label = "green:voip1";
|
|
gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
led@15 {
|
|
label = "green:usb";
|
|
gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
led_power_green: led@22 {
|
|
label = "green:power";
|
|
gpios = <&gpio 22 GPIO_ACTIVE_LOW>;
|
|
default-state = "on";
|
|
};
|
|
|
|
led_power_red: led@23 {
|
|
label = "red:power";
|
|
gpios = <&gpio 23 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
led@24 {
|
|
label = "green:lan";
|
|
gpios = <&gpio 24 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
led@27 {
|
|
label = "green:wan";
|
|
gpios = <&gpio 27 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
|
|
bcm4322-sprom {
|
|
compatible = "brcm,ssb-sprom";
|
|
|
|
pci-bus = <0>;
|
|
pci-dev = <1>;
|
|
|
|
nvmem-cells = <&macaddr_cfe_6a0>;
|
|
nvmem-cell-names = "mac-address";
|
|
mac-address-increment = <1>;
|
|
|
|
brcm,sprom = "brcm/bcm4322-sprom.bin";
|
|
brcm,sprom-fixups = <219 0xec08>;
|
|
};
|
|
};
|
|
|
|
&ehci {
|
|
status = "okay";
|
|
};
|
|
|
|
ðernet {
|
|
status = "okay";
|
|
|
|
nvmem-cells = <&macaddr_cfe_6a0>;
|
|
nvmem-cell-names = "mac-address";
|
|
};
|
|
|
|
&mdio_ext {
|
|
switch@1e {
|
|
compatible = "brcm,bcm53115";
|
|
reg = <30>;
|
|
|
|
dsa,member = <1 0>;
|
|
|
|
ports {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
port@0 {
|
|
reg = <0>;
|
|
label = "wan";
|
|
};
|
|
|
|
port@1 {
|
|
reg = <1>;
|
|
label = "lan1";
|
|
};
|
|
|
|
port@2 {
|
|
reg = <2>;
|
|
label = "lan2";
|
|
};
|
|
|
|
port@3 {
|
|
reg = <3>;
|
|
label = "lan3";
|
|
};
|
|
|
|
port@4 {
|
|
reg = <4>;
|
|
label = "lan4";
|
|
};
|
|
|
|
port@8 {
|
|
reg = <8>;
|
|
|
|
phy-mode = "rgmii";
|
|
ethernet = <&switch0port5>;
|
|
|
|
fixed-link {
|
|
speed = <1000>;
|
|
full-duplex;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
&switch0 {
|
|
dsa,member = <0 0>;
|
|
|
|
ports {
|
|
switch0port5: port@5 {
|
|
reg = <5>;
|
|
label = "extsw";
|
|
|
|
phy-mode = "rgmii";
|
|
|
|
fixed-link {
|
|
speed = <1000>;
|
|
full-duplex;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
&pflash {
|
|
status = "okay";
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
cfe: partition@0 {
|
|
label = "CFE";
|
|
reg = <0x000000 0x020000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@20000 {
|
|
label = "firmware";
|
|
reg = <0x020000 0xf40000>;
|
|
compatible = "brcm,bcm963xx-imagetag";
|
|
};
|
|
|
|
partition@f60000 {
|
|
label = "board_data";
|
|
reg = <0xf60000 0x080000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@fe0000 {
|
|
label = "nvram";
|
|
reg = <0xfe0000 0x020000>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&ohci {
|
|
status = "okay";
|
|
};
|
|
|
|
&pci {
|
|
status = "okay";
|
|
};
|
|
|
|
&uart0 {
|
|
status = "okay";
|
|
};
|
|
|
|
&usbh {
|
|
status = "okay";
|
|
};
|
|
|
|
&cfe {
|
|
compatible = "nvmem-cells";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
macaddr_cfe_6a0: macaddr@6a0 {
|
|
reg = <0x6a0 0x6>;
|
|
};
|
|
};
|