openwrt/target/linux/ath79/dts
Petr Štetiar 40530c8eb4 ath79: Add support for Ubiquiti Nanostation M (XW)
CPU:  AR9342 SoC
RAM:      64 MB DDR2
Flash:     8 MB NOR SPI
Ports: 2x100 MBit (24V PoE in, 24V PoE out), AR8236 switch
WLAN:  2.4/5 GHz
UART:      1 UART
LEDs:        Power, 2x Ethernet, 4x RSSI LEDs (orange, red, 2x green)
Buttons:     Reset

Flashing instructions using recovery method over TFTP

 1. Unplug the ethernet cable from the router.
 2. Using paper clip press and hold the router's reset button. Make sure
    you can feel it depressed by the paper clip. Do not release the button
    until step 4.
 3. While keeping the reset button pressed in, plug the ethernet cable
    back into the AP. Keep the reset button depressed until you see the
    device's LEDs flashing in upgrade mode (alternating LED1/LED3 and
    LED2/LED4), this may take up to 25 seconds.
 4. You may release the reset button, now the device should be in TFTP
    transfer mode.
 5. Set a static IP on your Computer's NIC. A static IP of 192.168.1.25/24
    should work.
 6. Plug the PoE injector's LAN cable directly to your computer.
 7. Start tftp client and issue following commands:
     tftp> binary
     tftp> connect 192.168.1.20
     tftp> put openwrt-ath79-generic-ubnt-nano-m-xw-squashfs-factory.bin

Tested-by: Joe Ayers <ae6xe@arrl.net>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-03-05 03:15:52 +01:00
..
ar724x.dtsi ath79: add pinmux node to ar724x.dtsi 2018-06-01 08:23:02 +02:00
ar934x.dtsi ath79: ar934x: assert mac/mdio reset together for gmac0 2019-03-05 03:02:34 +01:00
ar1022_iodata_wn-ag300dgr.dts treewide: dts: Remove default-state=off property from all gpio LED nodes 2018-12-17 08:16:28 +01:00
ar7100.dtsi ath79: fix dtc compiler warnings 2018-12-12 12:28:26 +01:00
ar7161_buffalo_wzr-hp-ag300h.dts ath79: dts: Unify naming of gpio-keys nodes 2019-01-26 21:09:12 +01:00
ar7161_dlink_dir-825-b1.dts treewide: dts: Remove default-state=off property from all gpio LED nodes 2018-12-17 08:16:28 +01:00
ar7161_netgear_wndr3700.dts ath79: specify "firmware" partition format for WNDR3700 and v2 2018-11-24 13:15:55 +01:00
ar7161_netgear_wndr3700.dtsi ath79: dts: Unify naming of gpio-keys nodes 2019-01-26 21:09:12 +01:00
ar7161_netgear_wndr3700v2.dts ath79: specify "firmware" partition format for WNDR3700 and v2 2018-11-24 13:15:55 +01:00
ar7161_netgear_wndr3800.dts ath79: specify "firmware" partition format for Netgear WNDR3800 2018-11-24 08:46:59 +01:00
ar7161_ubnt_routerstation-pro.dts ath79: add syscon compatible property to ar7100 ethernet nodes 2018-09-06 21:35:53 +02:00
ar7161_ubnt_routerstation.dts ath79: initial support for Ubiquiti RouterStation and RouterStation Pro 2018-08-27 19:31:17 +02:00
ar7161_ubnt_routerstation.dtsi ath79: dts: Unify naming of gpio-led nodes 2019-01-26 21:09:12 +01:00
ar7240_buffalo_whr-g301n.dts ath79: dts: Unify naming of gpio-keys nodes 2019-01-26 21:09:12 +01:00
ar7240_netgear_wnr612-v2.dts ath79: add SoC or family compatible 2018-12-06 13:28:22 +01:00
ar7240_netgear_wnr612-v2.dtsi ath79: dts: Unify naming of gpio-led nodes 2019-01-26 21:09:12 +01:00
ar7240_on_n150r.dts ath79: add SoC or family compatible 2018-12-06 13:28:22 +01:00
ar7240_tplink_tl-wr74xn-v1.dtsi ath79: dts: Unify naming of gpio-keys nodes 2019-01-26 21:09:12 +01:00
ar7240_tplink_tl-wr740n-v1.dts ath79: add SoC or family compatible 2018-12-06 13:28:22 +01:00
ar7240_tplink_tl-wr740n-v3.dts ath79: add SoC or family compatible 2018-12-06 13:28:22 +01:00
ar7240_tplink_tl-wr741-v1.dts ath79: add SoC or family compatible 2018-12-06 13:28:22 +01:00
ar7240_tplink_tl-wr743nd-v1.dts ath79: add SoC or family compatible 2018-12-06 13:28:22 +01:00
ar7240_tplink_tl-wr841-v5.dts ath79: add SoC or family compatible 2018-12-06 13:28:22 +01:00
ar7240_tplink_tl-wr941-v4.dts ath79: add SoC or family compatible 2018-12-06 13:28:22 +01:00
ar7240.dtsi ath79: fix dts warnings 2018-08-08 08:11:11 +02:00
ar7241_tplink_tl-mr3x20.dtsi treewide: dts: Remove default-state=off property from all gpio LED nodes 2018-12-17 08:16:28 +01:00
ar7241_tplink_tl-mr3220-v1.dts treewide: dts: Remove default-state=off property from all gpio LED nodes 2018-12-17 08:16:28 +01:00
ar7241_tplink_tl-mr3420-v1.dts treewide: dts: Remove default-state=off property from all gpio LED nodes 2018-12-17 08:16:28 +01:00
ar7241_tplink_tl-wr841-v7.dts ath79: rename TP-LINK to TP-Link 2019-02-14 16:56:14 +01:00
ar7241_tplink_tl-wr842n-v1.dts ath79: add support for TP-Link TL-WR842N/ND v1 router 2018-12-15 21:35:45 +01:00
ar7241_tplink.dtsi ath79: dts: Unify naming of gpio-keys nodes 2019-01-26 21:09:12 +01:00
ar7241_ubnt_airrouter.dts ath79: add SoC or family compatible 2018-12-06 13:28:22 +01:00
ar7241_ubnt_bullet-m.dts ath79: add SoC or family compatible 2018-12-06 13:28:22 +01:00
ar7241_ubnt_nano-m.dts ath79: add SoC or family compatible 2018-12-06 13:28:22 +01:00
ar7241_ubnt_rocket-m.dts ath79: add SoC or family compatible 2018-12-06 13:28:22 +01:00
ar7241_ubnt_unifi.dts ath79: Define firmware partition format to all boards where applicable 2018-12-06 13:28:22 +01:00
ar7241_ubnt_xm_outdoor.dtsi ath79: split ubnt outdoor device leds into separate dtsi 2018-12-03 07:58:49 +01:00
ar7241_ubnt_xm.dtsi ath79: Define firmware partition format to all boards where applicable 2018-12-06 13:28:22 +01:00
ar7241.dtsi ath79: fix dts warnings 2018-08-08 08:11:11 +02:00
ar7242_avm_fritz300e.dts ath79: dts: Unify naming of gpio-keys nodes 2019-01-26 21:09:12 +01:00
ar7242_buffalo_bhr-4grv.dts ath79: fix MAC address for Buffalo BHR-4GRV 2018-10-07 10:46:20 +02:00
ar7242_buffalo_wzr-bhr.dtsi treewide: dts: Remove default-state=off property from all gpio LED nodes 2018-12-17 08:16:28 +01:00
ar7242_buffalo_wzr-hp-g302h-a1a0.dts treewide: dts: Remove default-state=off property from all gpio LED nodes 2018-12-17 08:16:28 +01:00
ar7242_buffalo_wzr-hp-g450h.dts treewide: dts: Remove default-state=off property from all gpio LED nodes 2018-12-17 08:16:28 +01:00
ar7242_tplink_tl-wr2543-v1.dts ath79: rename TP-LINK to TP-Link 2019-02-14 16:56:14 +01:00
ar7242.dtsi ath79: Add switch reset definition in dts 2018-07-30 10:43:35 +02:00
ar9132_tplink_tl-wa901nd-v2.dts treewide: dts: Remove default-state=off property from all gpio LED nodes 2018-12-17 08:16:28 +01:00
ar9132_tplink_tl-wr941-v2.dts treewide: dts: Remove default-state=off property from all gpio LED nodes 2018-12-17 08:16:28 +01:00
ar9132_tplink_tl-wr1043nd-v1.dts ath79: make TP-Link revision naming consistent 2019-03-02 13:04:54 +01:00
ar9132.dtsi ath79: ag71xx: apply interface mode to MII0/1_CTRL on ar71xx/ar913x 2018-08-28 11:26:53 +02:00
ar9330_glinet_gl-ar150.dts ath79: fix boardname of GL.iNet GL-AR150 2018-12-31 14:05:26 +01:00
ar9330_pqi_air-pen.dts treewide: dts: Remove default-state=off property from all gpio LED nodes 2018-12-17 08:16:28 +01:00
ar9330.dtsi ath79: fix dts warnings 2018-08-08 08:11:11 +02:00
ar9331_dptechnics_dpt-module.dts treewide: dts: Remove default-state=off property from all gpio LED nodes 2018-12-17 08:16:28 +01:00
ar9331_dragino_ms14.dts treewide: dts: Remove default-state=off property from all gpio LED nodes 2018-12-17 08:16:28 +01:00
ar9331_embeddedwireless_dorin.dts treewide: dts: Remove default-state=off property from all gpio LED nodes 2018-12-17 08:16:28 +01:00
ar9331_etactica_eg200.dts treewide: dts: Remove default-state=off property from all gpio LED nodes 2018-12-17 08:16:28 +01:00
ar9331_onion_omega.dts treewide: dts: Remove default-state=off property from all gpio LED nodes 2018-12-17 08:16:28 +01:00
ar9331_pisen_wmm003n.dts ath79: dts: Unify naming of gpio-led nodes 2019-01-26 21:09:12 +01:00
ar9331_tplink_tl-mr10u.dts ath79: rename dts/image using manufacturer_board scheme 2018-08-06 07:31:54 +02:00
ar9331_tplink_tl-mr3020-v1.dts treewide: dts: Remove default-state=off property from all gpio LED nodes 2018-12-17 08:16:28 +01:00
ar9331_tplink_tl-mr3040-v2.dts treewide: dts: Remove default-state=off property from all gpio LED nodes 2018-12-17 08:16:28 +01:00
ar9331_tplink_tl-wr703n_tl-mr10u.dtsi ath79: dts: Unify naming of gpio-led nodes 2019-01-26 21:09:12 +01:00
ar9331_tplink_tl-wr703n.dts ath79: rename dts/image using manufacturer_board scheme 2018-08-06 07:31:54 +02:00
ar9331_tplink_tl-wr740n-v4.dts ath79: rename TL-WR740ND-v4 to TL-WR740N-v4 2019-02-14 16:56:14 +01:00
ar9331_tplink_tl-wr741nd-v4.dts ath79: add SoC or family compatible 2018-12-06 13:28:22 +01:00
ar9331_tplink_tl-wr741nd-v4.dtsi ath79: dts: Unify naming of gpio-led nodes 2019-01-26 21:09:12 +01:00
ar9331.dtsi ath79: add tl-mr3020-v1 support 2018-06-08 12:19:49 +02:00
ar9341_pcs_cr3000.dts treewide: dts: Remove default-state=off property from all gpio LED nodes 2018-12-17 08:16:28 +01:00
ar9341_tplink_tl-wr841-v8.dts ath79: add support for TP-Link TL-WR841N/ND v8 2018-12-31 13:28:31 +01:00
ar9341_tplink_tl-wr842n-v2.dts treewide: dts: Remove default-state=off property from all gpio LED nodes 2018-12-17 08:16:28 +01:00
ar9341.dtsi ath79: ar934x: Update dts for current ag71xx driver 2018-07-30 10:43:33 +02:00
ar9342_iodata_etg3-r.dts treewide: dts: Remove default-state=off property from all gpio LED nodes 2018-12-17 08:16:28 +01:00
ar9342_ubnt_bullet-m-xw.dts ath79: ubnt-bullet-m-xw: Remove eth1 disabled node 2018-12-27 16:02:25 +01:00
ar9342_ubnt_lap-120.dts ath79: add SoC or family compatible 2018-12-06 13:28:22 +01:00
ar9342_ubnt_nanostation-ac-loco.dts ath79: add SoC or family compatible 2018-12-06 13:28:22 +01:00
ar9342_ubnt_nanostation-ac.dts ath79: dts: Unify naming of gpio-led nodes 2019-01-26 21:09:12 +01:00
ar9342_ubnt_nanostation-m-xw.dts ath79: Add support for Ubiquiti Nanostation M (XW) 2019-03-05 03:15:52 +01:00
ar9342_ubnt_wa.dtsi ath79: add SoC or family compatible 2018-12-06 13:28:22 +01:00
ar9342_ubnt_xw.dtsi ath79: dts: Unify naming of gpio-led nodes 2019-01-26 21:09:12 +01:00
ar9344_comfast_cf-e120a-v3.dts ath79: add support for COMFAST CF-E120A v3 2019-02-28 11:26:10 +01:00
ar9344_dlink_dir-8x5.dtsi ath79: add d-link dir-825-c1 and dir-835-a1 2018-12-17 00:21:34 +01:00
ar9344_dlink_dir-825-c1.dts ath79: add d-link dir-825-c1 and dir-835-a1 2018-12-17 00:21:34 +01:00
ar9344_dlink_dir-835-a1.dts ath79: add d-link dir-825-c1 and dir-835-a1 2018-12-17 00:21:34 +01:00
ar9344_ocedo_raccoon.dts treewide: dts: Remove default-state=off property from all gpio LED nodes 2018-12-17 08:16:28 +01:00
ar9344_pcs_cap324.dts treewide: dts: Remove default-state=off property from all gpio LED nodes 2018-12-17 08:16:28 +01:00
ar9344_pcs_cr5000.dts treewide: dts: Remove default-state=off property from all gpio LED nodes 2018-12-17 08:16:28 +01:00
ar9344_tplink_tl-wdr3600.dts ath79: add SoC or family compatible 2018-12-06 13:28:22 +01:00
ar9344_tplink_tl-wdr4300.dts ath79: add SoC or family compatible 2018-12-06 13:28:22 +01:00
ar9344_tplink_tl-wdr4300.dtsi treewide: dts: Remove default-state=off property from all gpio LED nodes 2018-12-17 08:16:28 +01:00
ar9344_wd_mynet-wifi-rangeextender.dts ath79: add support for WD My Net Wi-Fi Range Extender 2018-09-10 09:07:41 +02:00
ar9344_winchannel_wb2000.dts treewide: dts: Remove default-state=off property from all gpio LED nodes 2018-12-17 08:16:28 +01:00
ar9344.dtsi ath79: fix dts warnings 2018-08-08 08:11:11 +02:00
ath79.dtsi ath79: ar934x: Update dts for current ag71xx driver 2018-07-30 10:43:33 +02:00
qca953x_tplink_tl-wr810n.dtsi ath79: Add support for TP-Link WR810N 2018-12-31 14:18:19 +01:00
qca953x.dtsi ath79: fix wmac memory region for qca953x 2019-02-20 18:51:31 +01:00
qca956x.dtsi ath79: fix pinmux reg value for QCA956x 2018-12-24 19:18:07 +01:00
qca9531_engenius_ews511ap.dts ath79: add support for EnGenius EWS511AP 2018-12-31 16:25:09 +01:00
qca9531_glinet_gl-ar300m-nand.dts ath79: fix boardname of GL.iNet GL-AR300M 2018-12-31 14:24:21 +01:00
qca9531_glinet_gl-ar300m-nor.dts ath79: fix boardname of GL.iNet GL-AR300M 2018-12-31 14:24:21 +01:00
qca9531_glinet_gl-ar300m.dtsi ath79: Modify glinet x750 and AR300m MAC address offsets 2019-02-28 11:32:55 +01:00
qca9531_glinet_gl-x750.dts ath79: Modify glinet x750 and AR300m MAC address offsets 2019-02-28 11:32:55 +01:00
qca9531_tplink_tl-wr810n-v1.dts ath79: Add support for TP-Link WR810N 2018-12-31 14:18:19 +01:00
qca9533_comfast_cf-e110n-v2.dts ath79: add support for COMFAST CF-E110N 2018-12-31 16:25:11 +01:00
qca9533_tplink_tl-wr810n-v2.dts ath79: Add support for TP-Link WR810N 2018-12-31 14:18:19 +01:00
qca9533_tplink_tl-wr841-v9.dts ath79: make TP-Link revision naming consistent 2019-03-02 13:04:54 +01:00
qca9533_tplink_tl-wr841-v11.dts ath79: make TP-Link revision naming consistent 2019-03-02 13:04:54 +01:00
qca9533_tplink_tl-wr841.dtsi treewide: dts: Remove default-state=off property from all gpio LED nodes 2018-12-17 08:16:28 +01:00
qca9557_buffalo_bhr-4grv2.dts ath79: dts: Unify naming of gpio-led nodes 2019-01-26 21:09:12 +01:00
qca9557_iodata_wn-ac1167dgr.dts ath79: add support for I-O DATA WN-AC1600DGR 2019-02-14 16:56:15 +01:00
qca9557_iodata_wn-ac1600dgr2.dts ath79: add support for I-O DATA WN-AC1600DGR 2019-02-14 16:56:15 +01:00
qca9557_iodata_wn-ac1600dgr.dts ath79: add support for I-O DATA WN-AC1600DGR 2019-02-14 16:56:15 +01:00
qca9557_iodata_wn-ac-dgr.dtsi ath79: add support for I-O DATA WN-AC1600DGR 2019-02-14 16:56:15 +01:00
qca9557.dtsi ath79: qca955x: assert mdio/gmac reset together 2019-03-05 03:02:34 +01:00
qca9558_devolo_dvl1xxx.dtsi ath79: add support for devolo WiFi pro 1200e 2018-12-27 14:06:38 +01:00
qca9558_devolo_dvl1200e.dts ath79: add support for devolo WiFi pro 1200e 2018-12-27 14:06:38 +01:00
qca9558_devolo_dvl1200i.dts ath79: add support for devolo WiFi pro 1200i 2019-01-05 21:55:22 +01:00
qca9558_devolo_dvl1750c.dts ath79: add support for devolo WiFi pro 1750c 2018-12-27 14:06:38 +01:00
qca9558_devolo_dvl1750e.dts ath79: add support for Devolo WiFi Pro 1750e 2019-01-26 21:46:33 +01:00
qca9558_devolo_dvl1750i.dts ath79: add support for devolo WiFi pro 1750i 2019-01-05 21:55:22 +01:00
qca9558_ocedo_koala.dts ath79: fix OCEDO Koala ethernet configuration 2018-12-30 20:08:13 +01:00
qca9558_openmesh_om5p-ac-v2.dts treewide: dts: Remove default-state=off property from all gpio LED nodes 2018-12-17 08:16:28 +01:00
qca9558_tplink_archer-c5-v1.dts ath79: add support for TP-Link Archer C5 v1 2019-02-28 11:32:55 +01:00
qca9558_tplink_archer-c7-v1.dts ath79: make TP-Link revision naming consistent 2019-03-02 13:04:54 +01:00
qca9558_tplink_archer-c7-v2.dts ath79: make TP-Link revision naming consistent 2019-03-02 13:04:54 +01:00
qca9558_tplink_archer-c7.dtsi treewide: dts: Remove default-state=off property from all gpio LED nodes 2018-12-17 08:16:28 +01:00
qca9558_tplink_tl-wdr4900-v2.dts treewide: dts: Remove default-state=off property from all gpio LED nodes 2018-12-17 08:16:28 +01:00
qca9558_tplink_tl-wr1043nd-v2.dts ath79: make TP-Link revision naming consistent 2019-03-02 13:04:54 +01:00
qca9558_tplink_tl-wr1043nd-v3.dts ath79: make TP-Link revision naming consistent 2019-03-02 13:04:54 +01:00
qca9558_tplink_tl-wr1043nd.dtsi treewide: dts: Remove default-state=off property from all gpio LED nodes 2018-12-17 08:16:28 +01:00
qca9561_avm_fritz4020.dts treewide: dts: Remove default-state=off property from all gpio LED nodes 2018-12-17 08:16:28 +01:00
qca9561_tplink_archer-c5x.dtsi ath79: add support for Archer C58/C59 v1 2018-11-26 12:05:45 +01:00
qca9561_tplink_archer-c58-v1.dts ath79: rename TP-LINK to TP-Link 2019-02-14 16:56:14 +01:00
qca9561_tplink_archer-c59-v1.dts ath79: rename TP-LINK to TP-Link 2019-02-14 16:56:14 +01:00
qca9561_xiaomi_mi-router-4q.dts ath79: add support for Xiaomi Mi Router 4Q 2019-02-11 19:04:06 +01:00
qca9563_dlink_dir-859-a1.dts ath79: add support for D-Link DIR-859 A1 2018-12-30 20:08:13 +01:00
qca9563_elecom_wrc-300ghbk2-i.dts ath79: add support for ELECOM WRC-1750GHBK2-I/C 2018-12-31 21:38:53 +09:00
qca9563_elecom_wrc-1750ghbk2-i.dts ath79: add support for ELECOM WRC-1750GHBK2-I/C 2018-12-31 21:38:53 +09:00
qca9563_elecom_wrc-ghbk2-i.dtsi ath79: add support for ELECOM WRC-1750GHBK2-I/C 2018-12-31 21:38:53 +09:00
qca9563_glinet_gl-ar750s.dts ath79: align GL-AR750S boardname to other GL.iNet devices 2019-01-01 19:42:41 +01:00
qca9563_nec_wg800hp.dts ath79: add support for NEC Aterm WG800HP 2018-12-24 19:18:07 +01:00
qca9563_phicomm_k2t.dts treewide: dts: Remove default-state=off property from all gpio LED nodes 2018-12-17 08:16:28 +01:00
qca9563_rosinson_wr818.dts ath79: tweak the position of factory partition for wr818 2018-12-31 16:37:09 +01:00
qca9563_tplink_archer-a7-v5.dts ath79: add support for TP-Link Archer A7 2018-12-17 08:09:13 +01:00
qca9563_tplink_archer-c2-v3.dts ath79: make TP-Link revision naming consistent 2019-03-02 13:04:54 +01:00
qca9563_tplink_archer-c6-v2.dts ath79: add support for TP-Link Archer C6 v2 2018-12-31 16:25:11 +01:00
qca9563_tplink_archer-c7-v4.dts ath79: TP-Link Archer C7 v4 swap usb led names 2019-03-02 12:59:48 +01:00
qca9563_tplink_archer-c7-v5.dts ath79: add support for TP-Link Archer C7 v5 2018-12-27 14:06:38 +01:00
qca9563_tplink_archer-x6-v2.dtsi ath79: add support for TP-Link Archer C6 v2 2018-12-31 16:25:11 +01:00
qca9563_tplink_archer-x7-v5.dtsi ath79: dts: Remove newly added default-state=off property 2018-12-17 14:22:28 +01:00
qca9563_tplink_re450-v2.dts treewide: dts: Remove default-state=off property from all gpio LED nodes 2018-12-17 08:16:28 +01:00
qca9563_tplink_tl-wr1043n.dtsi treewide: dts: Remove default-state=off property from all gpio LED nodes 2018-12-17 08:16:28 +01:00
qca9563_tplink_tl-wr1043nd-v4.dts ath79: make TP-Link revision naming consistent 2019-03-02 13:04:54 +01:00
qca9563_ubnt_unifiac-lite.dts ath79: add support for Unifi AC Mesh 2018-06-28 20:31:48 +02:00
qca9563_ubnt_unifiac-lite.dtsi ath79: add support for Unifi AC Mesh 2018-06-28 20:31:48 +02:00
qca9563_ubnt_unifiac-mesh-pro.dts ath79: add support for UniFi AC-Mesh Pro 2018-07-07 21:07:40 +02:00
qca9563_ubnt_unifiac-mesh.dts ath79: add support for Unifi AC Mesh 2018-06-28 20:31:48 +02:00
qca9563_ubnt_unifiac-pro.dts ath79: add support for UniFi AC-Mesh Pro 2018-07-07 21:07:40 +02:00
qca9563_ubnt_unifiac-pro.dtsi ath79: add support for UniFi AC-Mesh Pro 2018-07-07 21:07:40 +02:00
qca9563_ubnt_unifiac.dtsi ath79: Fix UBNT Unifi AC LEDs 2018-12-31 13:28:31 +01:00