Remove 100-musl_fix.patch, which is no longer needed
and causes a build error with gcc-14.
Fixes:
useful_functions.c:63:41: error: passing argument 1 of 'ether_ntoa' from incompatible pointer type [-Wincompatible-pointer-types]
63 | printf("%s", ether_ntoa((struct ether_addr *) mac));
| ^~~~~~~~~~~~~~~~~~~~~~~~~
| |
| struct ether_addr *
In file included from include/ebtables_u.h:28,
from useful_functions.c:25:
/Volumes/wrt3200/openwrt/staging_dir/toolchain-arm_cortex-a9+vfpv3-d16_gcc-14.1.0_musl_eabi/include/netinet/ether.h:10:19: note: expected 'const struct ether_addr *' but argument is of type 'struct ether_addr *'
10 | char *ether_ntoa (const struct ether_addr *);
| ^~~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Georgi Valkov <gvalkov@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15576
Signed-off-by: Robert Marko <robimarko@gmail.com>
Dell/SonicWall APL26-0AE (marketed as SonicPoint ACe) is a dual band
wireless access point. End of life as of 2022-07-31.
Specification
SoC: QualcommAtheros QCA9550
RAM: 256 MB DDR2
Flash: 32 MB SPI NOR
WIFI: 2.4 GHz 3T3R integrated
5 GHz 3T3R QCA9890 oversized Mini PCIe card
Ethernet: 2x 10/100/1000 Mbps QCA8334
port labeled lan1 is PoE capable (802.3at)
USB: 1x 2.0
LEDs: LEDs: 6x which 5 are GPIO controlled and two of them are dual color
Buttons: 2x GPIO controlled
Serial: RJ-45 port, SonicWall pinout
baud: 115200, parity: none, flow control: none
Before flashing, be sure to have a copy of factory firmware, in case You
wish to revert to original firmware.
All described procedures were done in following environment:
ROM Version: SonicROM (U-Boot) 8.0.0.0-11o
SafeMode Firmware Version: SonicOS 8.0.0.0-14o
Firmware Version: SonicOS 9.0.1.0
In case of other versions, following installation instructions might be
ineffective.
Installation
1. Prepare TFTP server with OpenWrt sysupgrade image and rename that
image to "sp_fw.bin".
2. Connect to one of LAN ports.
3. Connect to serial port.
4. Hold the reset button (small through hole on side of the unit),
power on the device and when prompted to stop autoboot, hit any key.
The held button can now be released.
5. Alter U-Boot environment with following commands:
setenv bootcmd bootm 0x9F110000
saveenv
6. Adjust "ipaddr" (access point, default is 192.168.1.1) and "serverip"
(TFTP server, default is 192.168.1.10) addresses in U-Boot
environment, then run following commands:
tftp 0x80060000 sp_fw.bin
erase 0x9F110000 +0x1EF0000
cp.b 0x80060000 0x9F110000 $filesize
7. After successful flashing, execute:
boot
8. The access point will boot to OpenWrt. Wait few minutes, until the
wrench LED will stop blinking, then it's ready for configuration.
Known issues
Initramfs image can't be bigger than specified kernel size, otherwise
bootloader will throw LZMA decompressing error. Switching to lzma-loader
should workaround that.
This device has Winbond 25Q256FVFG and doesn't have reliable reset, which
causes hang on reboot, thus broken-flash-reset needs to be added. This
property addition causes dispaly of "scary" warning on each boot, take
this warnig into consideration.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
This commit adds a new mlxreg package, which allows access
to Mellanox programmable device register space through sysfs
interface for thermal control and hardware management.
It also adds required Mellanox I²C drivers and packages
for the "special" MSN4800 series and SN2201 platform.
Signed-off-by: Til Kaiser <mail@tk154.de>
Add support for ELECOM WRC-X1800GS on uboot-envtools, to update
bootmenu_delay variable on sysupgrade.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Common specifications:
* Mediatek MT7988A (4x Cortex-A73, up to 1.8 GHz clock speed)
* 8 GiB eMMC
* 2 GiB DDR4 RAM
* 1x 10000M/1000M/100M + 3x 1000M/100M/10M LAN ports
* MT7996 Tri-band (2.4G, 5G, 6G) 4T4R 802.11be Wi-Fi
* Airoha AG3352 GPS
* Renesas DA14531MOD Bluetooth
* 2 buttons (Reset, Mesh/WPS)
* uC-controlled RGB LED via I2C
* 2x LED for each 1G port, 3x LED for each 10G port
* USB 3.0 type A port
* 3.3V-level 115200 baud UART console via 4-pin Dupont connector
exposed at the bottom of the device
* USB-C PD power input
SDG-8733: 1x 10000M/1000M/100M WAN port
SDG-8734: 1x USXGMII/10GBase-R/5GBase-R/2500Base-X/1000Base-X/SGMII SFP+
Both models are also available in versions including 2x FXS POTS interfaces
for analog phones. Those interfaces are not supported by OpenWrt.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Basic changes to make linux-atm build without any issues with GCC 14.
Besides some errors caused by -Wpointer-sign, there was also an issue
with socklen_t not being used for getsockopt() and accept()
sometimes.
I also updated the Debian patch to include the latest changes from
version "1:2.5.1-5.1" in Debian Sid. This allowed me to drop
"600-fix-format-errors.patch" and "700-include_sockios.patch".
Signed-off-by: Rany Hany <rany_hany@riseup.net>
This 4G/LTE modem is a WiFi hotspot, and also works as cdc_ether modem
when plugged over USB. It needs usb-modeswitching. With HuaweiNewMode,
it will modeswitch from 3426:1f01 (mass-storage) to 3426:14db
(cdc_ether).
Signed-off-by: Didier 'OdyX' Raboud <odyx@raksha.ch>
Link: https://github.com/openwrt/openwrt/pull/15497
Signed-off-by: Robert Marko <robimarko@gmail.com>
Other than OPKG which only uses signed package list, APK uses
individually signed packages in addition to signed package lists. Hence,
in order to be able to generate package, the private key needs to be
generated before compiling packages. Express that dependency and
generate the private key before building any packages instead of doing
so as part of the base-files package build.
Fixes: d788ab376f ("build: add APK package build capabilities")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This commit adds support for Netgear Orbi Pro SXR80 and SXS80 (collectively known as SXK80)
Specifications:
---------------
* CPU: Qualcomm IPQ8074A Quad core Cortex-A53
* RAM: 1024MB
* Storage: SPI-NAND 512 MiB (Winbond W29N04GZ)
* Ethernet: 4x 1G RJ45 ports (QCA8075) 1x 2.5G RJ45 LAN/WAN (QCA8081)
* WLAN:
- 2.4 GHz: Qualcomm QCN5024 4x4
- 2x 5 GHz: Qualcomm QCN5054 4x4 (second radio high channels only)
* LEDs:
- Power: (Green and red)
- Front: (Blue, green, red and white)
* Buttons:
- 1x Soft reset
- 1x Sync/WPS
* Power: 12V DC Jack
Installation instructions (Telnet):
-----------------------------------
*Note, this guide assumes SXR80, for SXS80 change the firmware file name as appropriate
1. Put firmware file openwrt-qualcommax-ipq807x-netgear_sxr80-initramfs-uImage.itb in root of TFTP server available at 192.168.1.10.
2. Enable telnet by going to http://[ip of device]/debug.htm and clicking on the tickbox 'Enable telnet'
3. Telnet into the device and login using the same username and password as the web interface:
4. Run the following command:
`fw_setenv bootcmd 'env default -a; saveenv; reset'`
5. Reboot the router, once the web interface is available again re-enable telnet via http://[ip of device]/debug.htm and telnet into the device.
6. Run the following command:
`fw_printenv`
It should look similar to the below:
```
baudrate=115200
bootargs=console=ttyMSM0,115200n8
bootcmd=mii write 0x0 0x0 0x800; sleep 1; nmrp; bootdni; boot_DNI_secureboot
bootdelay=2
ipaddr=192.168.1.1
netmask=255.255.255.0
serverip=192.168.1.10
soc_version_major=2
soc_version_minor=0
```
**If you see the message:**
`Warning: Bad CRC, using default environment`
**DO NOT CONTINUE, YOU WILL BRICK YOUR DEVICE**
7. Run the following command:
`fw_setenv originalboot 'mii write 0x0 0x0 0x800; sleep 1; nmrp; bootdni; boot_DNI_secureboot'`
(This should match what's in the bootcmd variable displayed in step 6)
8. Run the following commands:
```
fw_setenv wrttftp 'mii write 0x0 0x0 0x800; sleep 1; nmrp; if tftpboot openwrt-qualcommax-ipq807x-netgear_sxr80-initramfs-uImage.itb; then bootm; fi; bootdni; boot_DNI_secureboot'
fw_setenv wrtboot 'mii write 0x0 0x0 0x800; sleep 1; nmrp; nand read 0x40000000 0x1980000 0x06d00000; bootm 0x40000000'
fw_setenv bootcmd 'run wrttftp'
```
9. Ensure SXR/S device is attached via ethernet (LAN port) to the same ethernet segment as the TFTP server.
10. Reboot the device, it should reboot into OpenWrt and be available on 192.168.1.1
11. Once OpenWrt has booted, update the bootcmd using the following command:
`fw_setenv bootcmd 'run wrtboot'`
12. Flash the sysupgrade image
13. It should boot into OpenWrt
References to SXK80 GPL source:
https://www.downloads.netgear.com/files/GPL/SXK80-V3.2.0.108_gpl_src.tar.bz2.zip
Signed-off-by: Flole Systems <flole@flole.de>
Signed-off-by: Andrew Smith <gul.code@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/14939
Signed-off-by: Robert Marko <robimarko@gmail.com>
During the last update to 12.5.r2 printing of the attached PHY-s was
removed, so lets bring it back as it is very helpfull for debugging
OpenWrt issues without users having to modify NSS-DP to know if a PHY
was attached.
Refresh patches since nss_dp_main.c was edited.
Link: https://github.com/openwrt/openwrt/pull/15537
Signed-off-by: Robert Marko <robimarko@gmail.com>
The IXP4xx is well supported upstream and can readily be
supported with kernel v6.6. To simplify things after the
DTS directory was renamed, switch to v6.6 only.
Bring in some outstanding patches.
Tested on the Gateworks GW2348-4.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Changes:
73529a8 Revert "wireless-regdb: Update and disable 5470-5730MHz band according to TPC requirement for Singapore (SG)"
87941e4 wireless-regdb: Update regulatory rules for Taiwan (TW) on 6GHz
33797ae wireless-regdb: update regulatory database based on preceding changes
Signed-off-by: Yuu Toriyama <PascalCoffeeLake@gmail.com>
Add ubi volumes for mt7988a-rfb and support for using factory data
for Ethernet MAC addresses and MT7996 WLAN calibration data.
Also add rootdisk handle. Removes the need to keep using nmbm
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Drop downstream mbedtls patch since it went upstream.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Link: https://github.com/openwrt/openwrt/pull/15522
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The function incorrectly tried to APK keys even if there were none.
Correctly separate it into its own `ifdef` section.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Link: https://github.com/openwrt/openwrt/pull/15519
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The host build would need Lua to compile which currently adds a race
condition. Instead of tracking that down just disable helptext for the
host build.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Both package managers work slightly different, i.e. stores files at
different places. Modify the `functions.sh` file to cover those.
Signed-off-by: Paul Spooren <mail@aparcar.org>
The APK package manager does not support handling of package
alternatives itself, so implement it via a simple shell script.
Signed-off-by: Paul Spooren <mail@aparcar.org>
A new option called `USE_APK` is added which generated APK packages
(.apk) instead of OPKG packages (.ipk).
Some features like fstools `snapshot` command are not yet ported
Signed-off-by: Paul Spooren <mail@aparcar.org>
Since swig is mentioned as build dependency and buildbots have it
installed we can safely bump version.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Hardware specification:
========
SoC: Qualcomm IPQ8072A
Flash: 512MB (Fidelix FMND4G08S3J-ID)
RAM: 1GB (2x Kingston DDR3L D2516ECMDXGJD)
Ethernet: 1x 10/100/1000/2500/5000Mbps (Marvell AQR114C)
Ethernet: 4x 10/100/1000Mbps (Qualcomm QCA8075)
WiFi1: 6GHz ax 4x4 (Qualcomm QCN9024 + Skyworks SKY85784-11) - channels 33-229
WiFi2: 5GHz ax 4x4 (Qualcomm QCN5054 + Skyworks SKY85755-11) - channels 36-177
WiFi3: 2.4GHz ax 4x4 (Qualcomm QCN5024 + Skyworks SKY8340-11)
IoT: Bluetooth 5, Zigbee and Thread (NXP K32W041)
LED: 1x RGB status (NXP PCA9633)
USB: 1x USB 3.0
Button: WPS, Reset
Flash instructions:
========
1. Manually upgrade firmware using openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin image.
More details can be found here: https://www.linksys.com/support-article?articleNum=47547
After first boot check actual partition:
- fw_printenv -n boot_part
and install firmware on second partition using command in case of 2:
- mtd -r -e kernel -n write openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin kernel
and in case of 1:
- mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin alt_kernel
2. Installation using serial connection from OEM firmware (default login: root, password: admin):
- fw_printenv -n boot_part
In case of 2:
- flash_erase /dev/mtd21 0 0
- nandwrite -p /dev/mtd21 openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin
or in case of 1:
- flash_erase /dev/mtd23 0 0
- nandwrite -p /dev/mtd23 openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin
After first boot install firmware on second partition:
- mtd -r -e kernel -n write openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin kernel
or:
- mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin alt_kernel
3. Installation from initramfs image using USB drive:
Put the initramfs image on the USB drive:
- dd bs=1M if=openwrt-qualcommax-ipq807x-linksys_mx8500-initramfs-uImage.itb of=/dev/sda
Stop u-boot and run:
- usb start && usbboot $loadaddr 0 && bootm $loadaddr
Write firmware to the flash from initramfs:
- mtd -e kernel -n write openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin kernel
and:
- mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin alt_kernel
4. Back to the OEM firmware:
- mtd -e kernel -n write FW_MX8500_1.0.11.208937_prod.img kernel
and:
- mtd -r -e alt_kernel -n write FW_MX8500_1.0.11.208937_prod.img alt_kernel
5. USB recovery:
Put the initramfs image on the USB:
- dd bs=1M if=openwrt-qualcommax-ipq807x-linksys_mx8500-initramfs-uImage.itb of=/dev/sda
Set u-boot env:
- fw_setenv bootusb 'usb start && usbboot $loadaddr 0 && bootm $loadaddr'
- fw_setenv bootcmd 'run bootusb; if test $auto_recovery = no; then bootipq; elif test $boot_part = 1; then run bootpart1; else run bootpart2; fi'
AQR firmware:
========
1. Firmware loading:
To properly load the firmware and initialize AQR PHY, we must use the u-boot aq_load_fw function.
To do this, you need to modify u-boot env:
With USB recovery:
- fw_setenv bootcmd 'aq_load_fw; run bootusb; if test $auto_recovery = no; then bootipq; elif test $boot_part = 1; then run bootpart1; else run bootpart2; fi'
and without:
- fw_setenv bootcmd 'aq_load_fw; if test $auto_recovery = no; then bootipq; elif test $boot_part = 1; then run bootpart1; else run bootpart2; fi'
2. Firmware updating:
Newer firmware (AQR-G4_v5.6.5-AQR_WNC_SAQA-L2_GT_ID45287_VER24005.cld) is available in the latest OEM firmware.
To load this firmware via u-boot, we need to add the MBN header and update 0:ethphyfw partition.
For MBN header we can use script from this repository: https://github.com/testuser7/aqr_mbn_tool
- python aqr_mbn_tool.py AQR-G4_v5.6.5-AQR_WNC_SAQA-L2_GT_ID45287_VER24005.cld
To update partition we need to install kmod-mtd-rw package first:
- insmod mtd-rw.ko i_want_a_brick=1
- mtd -e /dev/mtd26 -n write aqr_fw.mbn /dev/mtd26
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/14883
Signed-off-by: Robert Marko <robimarko@gmail.com>
This adds support for the RTL8723BE PCIe Wi-Fi Adapter by adding backports drivers
Signed-off-by: David Adriao <davidadriao@dglitch.com>
[Do not remove rtl8xxxu and add dependency to rtl8723be-firmware]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This is required for linux-6.1 compatibility.
IRQs are not automatically mapped from HW to virtual IRQ numbers when
the IRQ domain is registered. This happens when the IRQ number is read
from the device tree based on the IRQ domain from the device tree now.
In kernel 5.15 it was done when the IRQ domain was registered.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
This is required for linux-6.1 compatibility.
IRQs are not automatically mapped from HW to virtual IRQ numbers when
the IRQ domain is registered. This happens when the IRQ number is read
from the device tree based on the IRQ domain from the device tree now.
In kernel 5.15 it was done when the IRQ domain was registered.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
This is required for linux-6.1 compatibility.
IRQs are not automatically mapped from HW to virtual IRQ numbers when
the IRQ domain is registered. This happens when the IRQ number is read
from the device tree based on the IRQ domain from the device tree now.
In kernel 5.15 it was done when the IRQ domain was registered.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
This makes the components used on the lantiq SoCs compile with kernel
6.1.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
[also fix ifxmips_ptm_adsl.c]
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
We simply grep for "src/". So no need for "\/".
Furthermore, since grep-3.8 this creates warnings.
As written in the grep-3.8 announcement:
Regular expressions with stray backslashes now cause warnings, as
their unspecified behavior can lead to unexpected results.
For example, '\a' and 'a' are not always equivalent
<https://bugs.gnu.org/39678>.
Fixes a warning during the first boot:
grep: warning: stray \ before /
Signed-off-by: Georgi Valkov <gvalkov@gmail.com>
gpio.h has been deprecated for a while and no longer compiles with 6.6.
Include the proper header.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15471
Signed-off-by: Robert Marko <robimarko@gmail.com>
Currently, trying to compile qca-ssdk on macOS will fail in a weird way:
make[6]: *** No rule to make target 'openwrt/build_dir/target-aarch64_cortex-a53_musl/linux-qualcommax_ipq807x/qca-ssdk-2024.04.17~3d060f7a/-n',
needed by 'openwrt/build_dir/target-aarch64_cortex-a53_musl/linux-qualcommax_ipq807x/qca-ssdk-2024.04.17~3d060f7a/qca-ssdk.o'. Stop.
After looking looking at src_list.dep from which KBuild cmd_mod will
generate the list of objects to compile it looked like:
-n /src/adpt/adpt.c
-n
-n
Which was rather suspicous so after comparing to the same file but with
Fedora as host:
/src/adpt/adpt.c src/adpt/hppe/adpt_hppe_fdb.c src/adpt/hppe/adpt_hppe_mib.c
It was clear that echo -n which was used in SSDK-s target.mk was not
working as intented, and it looked like the POSIX only version of echo
was being used which does not honor -n.
So, after failling to reproduce it externally, replacing the call to echo
with a full path to coreutils echo fixed the compilation.
After further debugging, it was determined that SSDK does not honor
CONFIG_SHELL like other kernel modules so it was defaulting to /bin/sh as
the shell make was calling thus calling the /bin/sh built-in echo which on
macOS is the old Bash 3.2 one and it does not respect -n.
So, we have to explicitly pass SHELL=$(BASH) to SSDK to make it use bash
like kernel build or other kernel modules.
This is not an issue since on macOS we always build bash anyway.
Link: https://github.com/openwrt/openwrt/pull/15459
Signed-off-by: Robert Marko <robimarko@gmail.com>
FCC ID: A8J-EWS660AP
Engenius ENS1750 is an outdoor wireless access point with
2 gigabit ethernet ports, dual-band wireless,
internal antenna plates, and 802.3at PoE+
Engenius EWS660AP, ENS1750, and ENS1200 are "electrically identical,
different model names are for marketing purpose" according to docs
provided by Engenius to the FCC.
**Specification:**
- QCA9558 SOC 2.4 GHz, 3x3
- QCA9880 WLAN mini PCIe card, 5 GHz, 3x3, 26dBm
- AR8035-A PHY RGMII GbE with PoE+ IN
- AR8033 PHY SGMII GbE with PoE+ OUT
- 40 MHz clock
- 16 MB FLASH MX25L12845EMI-10G
- 2x 64 MB RAM
- UART at J1 populated, RX grounded
- 6 internal antenna plates (5 dbi, omni-directional)
- 5 LEDs, 1 button (power, eth0, eth1, 2G, 5G) (reset)
**MAC addresses:**
Base MAC addressed labeled as "MAC"
Only one Vendor MAC address in flash
eth0 *:d4 MAC art 0x0
eth1 *:d5 --- art 0x0 +1
phy1 *:d6 --- art 0x0 +2
phy0 *:d7 --- art 0x0 +3
**Serial Access:**
the RX line on the board for UART is shorted to ground by resistor R176
therefore it must be removed to use the console
but it is not necessary to remove to view boot log
optionally, R175 can be replaced with a solder bridge short
the resistors R175 and R176 are next to the UART RX pin
**Installation:**
2 ways to flash factory.bin from OEM:
Method 1: Firmware upgrade page:
OEM webpage at 192.168.1.1
username and password "admin"
Navigate to "Firmware Upgrade" page from left pane
Click Browse and select the factory.bin image
Upload and verify checksum
Click Continue to confirm and wait 3 minutes
Method 2: Serial to load Failsafe webpage:
After connecting to serial console and rebooting...
Interrupt uboot with any key pressed rapidly
execute `run failsafe_boot` OR `bootm 0x9fd70000`
wait a minute
connect to ethernet and navigate to
"192.168.1.1/index.htm"
Select the factory.bin image and upload
wait about 3 minutes
**Return to OEM:**
If you have a serial cable, see Serial Failsafe instructions
otherwise, uboot-env can be used to make uboot load the failsafe image
ssh into openwrt and run
`fw_setenv rootfs_checksum 0`
reboot, wait 3 minutes
connect to ethernet and navigate to 192.168.1.1/index.htm
select OEM firmware image from Engenius and click upgrade
**TFTP recovery:**
Requires serial console, reset button does nothing
rename initramfs.bin to '0101A8C0.img'
make available on TFTP server at 192.168.1.101
power board, interrupt boot
execute tftpboot and bootm 0x81000000
**Format of OEM firmware image:**
The OEM software of ENS1750 is a heavily modified version
of Openwrt Kamikaze. One of the many modifications
is to the sysupgrade program. Image verification is performed
simply by the successful ungzip and untar of the supplied file
and name check and header verification of the resulting contents.
To form a factory.bin that is accepted by OEM Openwrt build,
the kernel and rootfs must have specific names...
openwrt-ar71xx-generic-ens1750-uImage-lzma.bin
openwrt-ar71xx-generic-ens1750-root.squashfs
and begin with the respective headers (uImage, squashfs).
Then the files must be tarballed and gzipped.
The resulting binary is actually a tar.gz file in disguise.
This can be verified by using binwalk on the OEM firmware images,
ungzipping then untaring.
Newer EnGenius software requires more checks but their script
includes a way to skip them, otherwise the tar must include
a text file with the version and md5sums in a deprecated format.
The OEM upgrade script is at /etc/fwupgrade.sh.
OKLI kernel loader is required because the OEM software
expects the kernel to be no greater than 1536k
and the factory.bin upgrade procedure would otherwise
overwrite part of the kernel when writing rootfs.
Note on PLL-data cells:
The default PLL register values will not work
because of the external AR8035 switch between
the SOC and the ethernet port.
For QCA955x series, the PLL registers for eth0 and eth1
can be see in the DTSI as 0x28 and 0x48 respectively.
Therefore the PLL registers can be read from uboot
for each link speed after attempting tftpboot
or another network action using that link speed
with `md 0x18050028 1` and `md 0x18050048 1`.
The clock delay required for RGMII can be applied
at the PHY side, using the at803x driver `phy-mode`.
Therefore the PLL registers for GMAC0
do not need the bits for delay on the MAC side.
This is possible due to fixes in at803x driver
since Linux 5.1 and 5.3
Tested-by: Kevin Abraham <kevin@westhousefarm.com>
Signed-off-by: Kevin Abraham <kevin@westhousefarm.com>
Linux kernel commit torvalds/linux@b8a1a4cd5a
added a temporary probe_new member to struct i2c_driver, to drop the
rarely used second parameter of the probe function and not break API for
out of tree drivers. With torvalds/linux@5eb1e6e459,
which is part of v6.6, this probe_new member is dropped and the
signature of the probe function is updated.
ubnt-ledbar is used by the mediatek and ramips targets and both have
been updated to v6.6, so adapt the probe function signature and remove
other compat code for versions before v6.6.
Signed-off-by: Sven Wegener <sven.wegener@stealer.net>
Link: https://github.com/openwrt/openwrt/pull/15443
Signed-off-by: Robert Marko <robimarko@gmail.com>
uid/gid range should be limited to 16bit unsigned integer range to
avoid "wraparound" issues with permissions where jffs2
is employed for storage and chown 65536 (first auto-created user)
becomes equivalent to chown 0
Fixes: #13927
Signed-off-by: Thomas Winkler <tewinkler86@gmail.com>
This includes multiple updates for BCM2711 and BCM2712.
Full changelog:
0968de2871...1.20240424
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Newer compilers default to building with C++17 as default, which has the
register keyword removed and thus errors.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
don't mention SHA1 in order to not confuse users - SHA1 support is already disabled (except RSA-SHA1 signagures).
ref: https://github.com/openwrt/openwrt/issues/15281
Signed-off-by: Konstantin Demin <rockdrilla@gmail.com>
- update dropbear to latest stable 2024.85;
for the changes see https://matt.ucc.asn.au/dropbear/CHANGES
- drop cherry-picked patches (merged in release 2024.84)
- refresh remaining patches
Tested-by: Stijn Segers <foss@volatilesystems.org>
Signed-off-by: Konstantin Demin <rockdrilla@gmail.com>
The 'nandbiterrs' tool is useful to find out of bit error correction of
NAND is working as expected by deliberately introducing bit errors and
telling up to which number they can be corrected.
Enable build of the testing tools and package the 'nandbiterrs' tool as
part of the nand-utils package.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
With the switch from the uImage.FIT partition parser to fitblk the
cmdline needs to be adjusted as well. Do this now as it has been
forgotten when the switch was done.
Fixes: 6368ed1ae5 ("mediatek: mt7623: phase out uImage.FIT partition parser")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
99dd990690bc treewide: refactor pref(erred) to preferred_lt (lifetime)
4c2b51eab368 treewide: refactor valid to valid_lt (lifetime)
3b4e06055900 router: inherit user-assigned preferred_lifetime
e164414aa184 router: limit prefix preferred_lt to valid_lt in accordance with RFC4861
a2176af7bdeb treewide: spell-fixes and new comments for extra clarification
4590efd3a2b3 treewide: normalize spaces to tabs
2edc60cb7c7a router: rename minvalid to lowest_found_lifetime
7ee72ee17bfa router: disambiguate and clarify 'no route' messages
a29882318a4c config: set RFC defaults for preferred lifetime
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
There is a new branch 12.5.r2 for kernel 6.6, so refresh
and update patches.
Delete patch 0010-nss-dp-include-net-netdev_rx_queue.h.patch
Changes:
2024-04-04 -5bf8b91 [qca-nss-dp] Adding support for port ID 3 & 4 in MHT switch
2024-03-28 -ce1e4cf [qca-nss-dp] Use skb_queue_head_init instead of __skb_queue_head_init.
2024-03-11 -0d26366 [qca-nss-dp] Read MHT LAN port status for ErP phase2
2024-03-22 -8382f14 [qca-nss-dp] Fix compilation issues seen on ginger branch for Miami profile
2023-05-02 -09b0983 [qca-nss-dp] vp list processing for capwap
2024-02-22 -bc09a01 [qca-nss-dp] EDMA ring reset for PPE-DS
2024-03-12 -2fcb586 [qca-nss-dp] Fix the EDMA clock frequency for the mitigation timer configuration
2024-02-23 -44ba1be [qca-nss-dp] Add API to retrieve ethernet netdevs for ErP
2024-02-09 -a5979b7 [qca-nss-dp] send napi and ip checksum for VP handler
2024-01-12 -1b9cb5d qca-nss-dp: User netdev_alloc_skb_fast instead of dev_alloc_skb
2024-01-08 -a859b48 [qca-nss-dp] NAPI Budget and EDMA Rx size change for KPI improvement.
2024-01-06 -8935523 [qca-nss-dp] Offload L3, L4 checksum to hardware for ppe-vp.
2023-12-07 -bbd9547 [qca-nss-dp] Fix Compilation issues on kernel6.6
2023-10-12 -bc55f75 [qca-nss-dp]: Enable legacy SCS for PPE-VP.
2023-09-08 -6bd771f [qca-nss-dp] Invalidate secondary descriptor before use.
2023-12-19 -b143df8 [qca-nss-dp] Fixed nss_dp_hal_hw_reset functionality for ipq53xx.
2023-12-16 -7cfde1d [qca-nss-dp] Added nss_dp_hal_hw_reset functionality for ipq53xx.
2023-11-02 -70af6c2 [qca-nss-dp] Implement EDMA hang recovery support
2023-11-27 -2202b29 [qca-nss-dp] Add support for adding the link speed for the Miami's port connected to the internal Switch.
2023-12-06 -bef68a8 [qca-nss-dp] Resolve ring utilization reporting issue in EDMA driver
2023-12-06 -eaa7627 [qca-nss-dp] Add/Delete static fdb entries only for physical ports
2023-10-16 -4551d0f [qca-nss-dp]: Support HLOST_TID_override from PPE_VP path.
2023-11-09 -42ad3f3 [qca-nss-dp] Correct the NAPI poll implementation for DS Rx fill handling
2023-10-16 -dfeb7d3 [qca-nss-dp] Check for disabled ethernet port in ErP functions
2023-11-09 -42ad3f3 [qca-nss-dp] Correct the NAPI poll implementation for DS Rx fill handling
2023-10-16 -dfeb7d3 [qca-nss-dp] Check for disabled ethernet port in ErP functions
2023-09-22 -03f83d6 [qca-nss-dp] Correct the mht device flag
2023-08-18 -5efd7f4 [qca-nss-dp] Add EDMA Tx rings for MHT ports
2023-09-11 -7808ba2 [qca-nss-dp] Move DP standby code to new file and use new SSDK API
2023-09-28 -22ade1e [qca-nss-dp] : enable PPE-DS support in 6.x kernel
2023-08-28 -1943922 [qca-nss-dp] Support for bitmap based CPU selection.
2023-08-16 -dcb82a7 qca-nss-dp: 512M profile changes for Miami+Pebble
2023-09-01 -18e51f3 [qca-nss-dp] Fix tx descriptor completion error.
2023-08-28 -0bfde2d [qca-nss-dp] Changes to enable ErP mode
2023-09-05 -f1d635a [qca-nss-dp] Enable fast recycled changes in dp for kernel 6.1
2023-06-15 -55d35bd [qca-nss-dp] Tracking the full utilization of EDMA rings
2023-08-25 -89b9c19 [qca-nss-dp] Restricting the MTU as 9216 for all interfaces in DP
2023-01-03 -5098a4f [qca-nss-dp] Requeue Tx packet in case of Tx-failure.
2023-04-06 -3576dbb [qca-nss-dp] Adding tx napi with four queue per interface.
2023-08-10 -d2b6921 [qca-nss-dp] : changes to support ppe-qdisc for linux 6.x
2023-08-08 -a1941fb [qca-nss-dp] moving SET_NETDEV_DEV for all netdev to set.
2023-07-18 -74d3178 [qca-nss-dp] Reordering the CPU code and ACL index processing.
2023-06-30 -ab03139 [qca-nss-dp] Configure port level PPE offload flag in PPE
2023-06-06 -e9bb8c5 [qca-nss-dp] Rate limit the debug logs.
2023-07-18 -43afb9b [qca-nss-dp] Support Core selection for PPE mirrored packets.
2023-07-11 -92edcfd [qca-nss-dp] Add sysctl to invalidate RX secondary descriptor.
Tested and working on WAX620.
Signed-off-by: Kristian Skramstad <kristian+github@83.no>
Link: https://github.com/openwrt/openwrt/pull/15383
Signed-off-by: Robert Marko <robimarko@gmail.com>
Qualcomm recently committed a new branch (12.5.r2) targeting kernel
6.6. This lets us clean up a few patches particularly the one for
"C22/C45" mdio.
A quick way to see what changed for IPQ807x/6018 was to list the files produced
during build (**/*.o), replace the extension with ".c", and doing a
`git log`.
Filtering from those commits, ones of particular interest are listed
below:
```
2024-04-16 - 0d8f30aa - fix compile issue on hk with linux style build
2024-01-29 - 636464f7 - update the check for port link notify
2024-01-24 - 30c10e7f - enable and disable loopback for xgmac to fix qm stuck issue
2024-01-15 - b6ea10aa - update the the APIs to access switch
2024-01-08 - a1687502 - Disable Tx bridge mac before power off the PHY
2024-01-07 - 3eafb613 - support led configure for malibu phy
2024-01-07 - 5c1af60d - remove phy type check from mac reset when mode switch
2023-12-17 - 79d0b1e8 - remove the PHY access APIs in ssdk_plat.c
2023-12-16 - b2953740 - Update mii read/write functions
2023-12-11 - 37f2eac3 - add port id check for fdb entry
2023-12-11 - d040ca4d - support mdio clause45 on kernel6.6
2023-12-07 - 11494fbc - use barrier mw() during access fdb entry table
2023-12-03 - 8e40a284 - fix build warnings on kernel6.6
2023-11-10 - 10aa0a02 - change speed value when call ssdk_port_link_notify
2023-11-06 - ee4c4a60 - Update mac bitmap value of L3 table on MAC delete
2023-11-03 - 7cd27d39 - support 10G phy common feature
2023-10-30 - 383cc0d2 - fix mactype and mux select issue
2023-10-24 - decf534a - support autoneg status query on force port
2023-10-11 - 111d574e - move ssdk_led_init to regi_init
2023-10-08 - 6b14c142 - the combo port also need to parse SFP pins
2023-10-03 - fb2e0401 - fix port5 interface mode switch issue in erp case
```
Verified with users on QNAP 301W, NBG7815, and myself on Dynalink
DL-WRX36 that everything is functional, including LEDS.
Signed-off-by: Sean Khan <datapronix@protonmail.com>
Link: https://github.com/openwrt/openwrt/pull/15379
Signed-off-by: Robert Marko <robimarko@gmail.com>
Enable building multiple test programs and related kernel modules, with
initial support for the bpf_testmod.ko module required since kernel 6.4.
Explicitly disable LTO and clean up makefile variables and formatting.
Fix a musl-related build failure by adding a kernel 6.6 patch:
360-selftests-bpf-portability-of-unprivileged-tests.patch
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
This has been tested on two of my Unifi 6 LR v2s:
```bash
$ fw_printenv # before
Cannot parse config file '/etc/fw_env.config': No such file or directory
$ cat /etc/fw_env.config
/dev/mtd3 0x0000 0x1000 0x1000 1
$ fw_printenv
arch=arm
baudrate=115200
board=mt7622_evb
board_name=mt7622_evb
bootcmd=bootubnt
bootdelay=3
bootfile=uImage
cpu=armv7
device_model=U6-LR
ethact=mtk_eth
ethaddr=<redacted>
ethcard=AQR112C
ipaddr=<redacted>
is_default=true
loadaddr=0x5007FF28
macaddr=<redacted>
serverip=<redacted>
soc=mt7622
stderr=serial
stdin=serial
stdout=serial
vendor=mediatek
is_ble_stp=true
```
I had to reverse-engineer the working settings above to the UCI script.
Signed-off-by: Joel Low <joel@joelsplace.sg>
Link: https://github.com/openwrt/openwrt/pull/13897
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The DropBear's dropbearkey supports limited set of arguments of
OpenSSH ssh-keygen: -t, -q -N -Y
After the change you can generate a key with the same command.
Still many features of the original OpenSSH ssh-keygen are absent in
the dropbearkey.
If it's needed then users should install openssh-keygen package that
will replace the /usr/bin/ssh-keygen with the full version.
Signed-off-by: Sergey Ponomarev <stokito@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/14174
[ wrap commit description to 80 columns ]
Link: https://github.com/openwrt/openwrt/pull/14174
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This adds support for the bpi-r4 variant with internal 2.5G PHY and
additional ethernet port instead of second sfp.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
This adds support for the bpi-r4 variant with internal 2.5G PHY and
additional ethernet port instead of second sfp.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Hardware:
=========
SOC: Qualcomm IPQ4019
WiFi 1: QCA4019 IEEE 802.11b/g/n
WiFi 2: QCA4019 IEEE 802.11a/n/ac
WiFi 3: QCA9886 IEEE 802.11a/n/ac
Bluetooth: Qualcomm CSR8510 (A10)
Zigbee: Silicon Labs EM3581 NCP + Skyworks SE2432L
Ethernet: Qualcomm Atheros QCA8072 (2-port)
Flash: Samsung KLM4G1FEPD (4GB eMMC)
RAM (NAND): 512MB
LED Controller: NXP PCA9633 (I2C)
Buttons: Single reset button (GPIO).
Ethernet:
=========
The device has 2 ethernet ports, configured as follows by default:
- left port: WAN
- right port: LAN
Wifi:
=====
The Wifi radios are turned off by default. To configure the router,
you will need to connect your computer to the LAN port of the device.
Bluetooth and Zigbee:
=====================
Configuration included but not tested.
Storage:
========
For compatibility with stock firmware, all of OpenWrt runs in a 136 MiB
eMMC partition (of which there are two copies, see below). You can also
use partition /dev/mmcblk0p19 "syscfg" (3.4 GiB) any way you see fit.
During very limited tests, stock firmware did not mount this partition.
However, backing up its stock content before use is recommended anyway.
Firmware:
=========
The device uses a dual firmware mechanism: it automatically reverts to
the previous firmware after 3 failed boot attempts.
You can switch to the inactive firmware copy by changing the "boot_part"
U-Boot environment variable. You can also do it by turning on the device
for a couple of seconds and then back off, 3 times in a row.
Installation:
=============
OpenWrt's "factory" image can be installed via the stock web UI:
1. Login to the UI. (The default password is printed on the label.)
2. Enter support mode by clicking on the "CA" link at the bottom.
3. Click "Connectivity", "Choose file", "Start", and ignore warnings.
This port is based on work done by flipy (https://github.com/flipy).
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15345
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add "linux64-loongarch64-openwrt" into openssl configurations to enable
building on loongarch64 machines.
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
* Allow kmod-acpi-video to be built for loongarch64:
The x86-specific CONFIG_ACPI_WMI will be split from default
kmod-acpi-video as a board-specific addition.
* Allow kmod-drm-amdgpu to be built for loongarch64:
Also add loongarch64-specific configs and modules.
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
To enable verbose log for xdp-tools compilation, we check for "c" in
the OPENWRT_VERBOSE, but verbose.mk supports only "w" and "s" for V=1
and V=99.
Fix the wrong matching and correctly enable verbose output matching for
"s".
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Upgrade the OpenSBI firmware used by RISC-V CPUs to 1.4.
Runtime-tested:
- d1 (Lichee RV)
- sifiveu (SiFive Unleashed)
Updates since last release:
1.4:
Synopsys DesignWare APB GPIO driver
Zicntr and Zihpm support
Console print improvements
Smepmp support
Simple FDT based syscon regmap driver
Syscon based reboot and poweroff driver
Non-contiguous hpm counters
Smcntrpmf support
Full sparse hartid support
IPI improvements
RFENCE improvements
Zkr support
Andes custom PMU support
1.3.1:
ACLINT driver fix for disabled CPUs
SBI PMU fix for out-of-bound access
Designware GPIO driver
1.3:
Allow platform to influence cold boot HART selection
Starfive JH7110 platform support
Split RX and RW firmware regions
Advertise non-retentive suspend for allwinner D1 platform
Byteorder/endianness conversion macros
SBI debug console extension (Experimental)
Configure the PMA regions for RZ/Five platform
SBI system suspend extension (Experimental)
SBI PMU platform firmware events (Experimental)
SBI CPPC extension (Experimental)
Optimized remote TLB flushes
Simple heap for boot time memory allocations
Bring back no-map DT property for reserved memory nodes
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
This is needed to boot the BCM6238-based Inteno XG6846.
Currently this is restricted to the XG6846 board.
Reviewed-by: Paul Donald <newtwen+github@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currently it's needed to have gcc-multilib on the host to correctly
compile xdp-tools. This is wrong and means that we are using host header
to compile a tool.
By some searching in how the makefile works it was discovered that
BPF_CFLAGS were not used and required to be appended to config.mk
Only one single header was added but we should include each BPF_CFLAGS
from bpf.mk. To make this some patching to bpf-header were required and
some patches to xdp-tools were required.
Also it's needed to pass the correct target to BPF_CFLAGS.
With the following changes xdp-tools can correctly compile with each
header from bpf-headers and should not use any host header.
Co-Developed-by: Andre Heider <a.heider@gmail.com>
Signed-off-by: Andre Heider <a.heider@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/11825
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
netlink.h header have NL_SET_ERR_MSG_MOD that is tied to kmods. We don't
need kmods on bpf tools and this cause compilation error if the header
is included. Fix it by dropping NL_SET_ERR_MSG_MOD.
Link: https://github.com/openwrt/openwrt/pull/11825
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
mDNS broadcast can't accept empty TXT record and would fail
registration.
Current procd_add_mdns_service checks only if the first passed arg is
empty but don't make any verification on the other args permittins
insertion of empty values in TXT record.
Example:
procd_add_mdns "blah" \
"tcp" "50" \
"1" \
"" \
"3"
Produce:
{ "blah_50": { "service": "_blah._tcp.local", "port": 50, "txt": [ "1", "", "3" ] } }
The middle empty TXT record should never be included as it's empty.
This can happen with scripts that make fragile parsing and include
variables even if they are empty.
Prevent this and make the TXT record more solid by checking every
provided TXT record and include only the non-empty ones.
The fixed JSON is the following:
{ "blah_50": { "service": "_blah._tcp.local", "port": 50, "txt": [ "1", "3" ] } }
Fixes: b0d9dcf84d ("procd: update to latest git HEAD")
Reported-by: Paul Donald <newtwen@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15331
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
