Kernel 5.15.82 added a prompt for the FUNCTION_ERROR_INJECTION symbol.
This is exposed in builds with CONFIG_KERNEL_KPROBES enabled, causing
those builds to fail due to a missing symbol. Add the symbol to fix
this.
Fixes: 68426e54ed ("kernel: bump 5.15 to 5.15.82")
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
The testing kernel has been running fine for months on a rather complex
network setup, with one exception being a crash in
__xfrm_state_delete(). This crash has been fixed in kernel 5.15.82, so
let's switch the qoriq target to kernel 5.15 by default.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Compex WPQ864 contains a non standard partition table. Each partition
node should be named partition and should contain a valid reg.
Fix an extra "-" present after the reg for SBL2_1 partition.
Also add "0:" to each qcom default partition following smem naming.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The refreshed patch actually use the format of <start size start size>
instead of <start end start end>. This cause boot fail since the rootfs
can't be mounted with these wrong values.
Fix it to the correct format in each affected dts.
Fixes: #11498
Fixes: 6134ba4a34 ("ipq806x: 5.15: add boot-partitions binding to fix block warning")
Tested-by: Matt Buczko <mbuczko@hotmail.com> # Askey RT4230W
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
TP-Link CPE605-v1 is an outdoor wireless CPE for 5 GHz with
one Ethernet port based on Atheros AR9344
Specifications:
- 560/450/225 MHz (CPU/DDR/AHB)
- 1x 10/100 Mbps Ethernet
- 64 MB of DDR2 RAM
- 8 MB of SPI-NOR Flash
- 23dBi high-gain directional antenna and a dedicated metal reflector
- Power, LAN, WLAN5G green LEDs
- 3x green RSSI LEDs
Flashing instructions:
Flash factory image through stock firmware WEB UI or through TFTP
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254
Signed-off-by: Andrew Cameron <apcameron@softhome.net>
Etisalat S3 is a wireless WiFi 5 router manufactured by Sercomm company.
Device specification
--------------------
SoC Type: MediaTek MT7621AT
RAM: 256 MiB
Flash: 128 MiB
Wireless 2.4 GHz (MT7603EN): b/g/n, 2x2
Wireless 5 GHz (MT7615E): a/n/ac, 4x4
Ethernet: 5x GbE (WAN, LAN1, LAN2, LAN3, LAN4)
USB ports: 1x USB3.0
Button: 2 buttons (Reset & WPS)
LEDs:
- 1x Status (RGB)
- 1x 2.4G (blue, hardware, mt76-phy0)
- 1x 5G (blue, hardware, mt76-phy1)
Power: 12 VDC, 1.5 A
Connector type: barrel
Bootloader: U-Boot
Installation
-----------------
1. Login to the router web interface under admin account
2. Navigate to Settings -> Configuration -> Save to Computer
3. Decode the configuration. For example, using cfgtool.py tool (see
related section):
cfgtool.py -u configurationBackup.cfg
4. Open configurationBackup.xml and find the following line:
<PARAMETER name="Password" type="string" value="<your router serial \
is here>" writable="1" encryption="1" password="1"/>
5. Insert the following line after and save:
<PARAMETER name="Enable" type="boolean" value="1" writable="1" encryption="0"/>
6. Encode the configuration. For example, using cfgtool.py tool:
cfgtool.py -p configurationBackup.xml
7. Upload the changed configuration (configurationBackup_changed.cfg) to
the router
8. Login to the router web interface (SuperUser:ETxxxxxxxxxx, where
ETxxxxxxxxxx is the serial number from the backplate label)
9. Navigate to Settings -> WAN -> Add static IP interface (e.g.
10.0.0.1/255.255.255.0)
10. Navigate to Settings -> Remote cotrol -> Add SSH, port 22,
10.0.0.0/255.255.255.0 and interface created before
11. Change IP of your client to 10.0.0.2/255.255.255.0 and connect the
ethernet cable to the WAN port of the router
12. Connect to the router using SSH shell under SuperUser account
13. Run in SSH shell:
sh
14. Make a mtd backup (optional, see related section)
15. Change bootflag to Sercomm1 and reboot:
printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3
reboot
16. Login to the router web interface under admin account
17. Remove dots from the OpenWrt factory image filename
18. Update firmware via web using OpenWrt factory image
Revert to stock
---------------
Change bootflag to Sercomm1 in OpenWrt CLI and then reboot:
printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3
mtd backup
----------
1. Set up a tftp server (e.g. tftpd64 for windows)
2. Connect to a router using SSH shell and run the following commands:
cd /tmp
for i in 0 1 2 3 4 5 6 7 8 9 10; do nanddump -f mtd$i /dev/mtd$i; \
tftp -l mtd$i -p 10.0.0.2; md5sum mtd$i >> mtd.md5; rm mtd$i; done
tftp -l mtd.md5 -p 10.0.0.2
Recovery
--------
Use sercomm-recovery tool.
Link: https://github.com/danitool/sercomm-recovery
MAC Addresses
-------------
+-----+------------+---------+
| use | address | example |
+-----+------------+---------+
| LAN | label | *:50 |
| WAN | label + 11 | *:5b |
| 2g | label + 2 | *:52 |
| 5g | label + 3 | *:53 |
+-----+------------+---------+
The label MAC address was found in Factory 0x21000
cfgtool.py
----------
A tool for decoding and encoding Sercomm configs.
Link: https://github.com/r3d5ky/sercomm_cfg_unpacker
Co-authored-by: Karim Dehouche <karimdplay@gmail.com>
Co-authored-by: Maximilian Weinmann <x1@disroot.org>
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
nvmem_cell_read return a pointer error when an error occurs. Currently
we convert the pointer error to an int while the rest of the function
return a void* and expcet an error pointer. Fix this PTR_ERR msuse
fixing compilation warning.
Fixes the following compilation warning:
net/ethernet/eth.c: In function 'nvmem_cell_get_mac_address':
net/ethernet/eth.c:547:24: warning: returning 'long int' from a function with return type 'void *' makes pointer from integer without a cast [-Wint-conversion]
547 | return PTR_ERR(mac);
| ^~~~~~~~~~~~
net/ethernet/eth.c: In function 'nvmem_cell_get_mac_address_ascii':
net/ethernet/eth.c:564:24: warning: returning 'long int' from a function with return type 'void *' makes pointer from integer without a cast [-Wint-conversion]
564 | return PTR_ERR(mac_ascii);
| ^~~~~~~~~~~~~~~~~~
Fixes: 7b863af180 ("kernel: move mac-address-ascii patches to generic")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Some Gemini devices are NAS type devices and need to ask for
DHCP IP on eth0. Some has a LAN/WAN setup. Add sensible
defaults for all known devices.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The patch managed to sneak into v5.15 whereas it was
properly deleted for v5.10.
Fixes: 8f6e2bb178 ("bcm53xx: remove MR32's specific get_leds_dt code")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Removed a20 in description, since it
only works for a10, a13 and a31.
Also refreshed kernel config.
Fixes: #10466
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
(moved fixes, refreshed, added CONFIG_DVB_USB=n)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
AddDepends/rtc has been removed in commit 3da7fe6, same here.
Fixes: 3da7fe6 ("kernel: remove useless AddDepends/rtc abstraction")
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
(RTC_SUPPORT - though this is implied by the TARGET_sunxi)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
enable option `CONFIG_CRYPTO_LZ4HC` to match default kernel config
this only adds the `lz4hc_compress` module, and has no effect on the
`lz4_decompress` module which already supports any flavor
Signed-off-by: Tony Butler <spudz76@gmail.com>
Reported by user: missing driver for USB; add to image definition
https://github.com/openwrt/openwrt/issues/11326Resolves: #11326
Signed-off-by: Tony Butler <spudz76@gmail.com>
Acked-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Make the patches apply cleanly again.
Fixes: 8327e0fb72 ("kernel: backport the dev_set_threaded export to 5.10")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This patch enables USB support for the GL.iNet GL-A1300
Repair the usb driver startup phase is not loaded
Signed-off-by: Weiping Yang <weiping.yang@gl-inet.com>
The MAC-Address setup for the Teltonika RUT230 v1 was swapped for the
LAN / WAN ports. Also the Label-MAC was assigned incorrect, as the WiFi
MAC is printed on the case as part of the SSID, however only the LAN
MAC-Address is designated as a MAC-Address.
Signed-off-by: David Bauer <mail@david-bauer.net>
add three missing LEDs
- PoE-Max
- Link/Act
- PoE
add two missing buttons
- mode
- reset
The last was dropped in
commit 61a3d0075b ("realtek: update GPIO bindings in the dts files in dts-5.10")
Signed-off-by: Jan-Niklas Burfeind <git@aiyionpri.me>
General hardware info:
----------------------
D-Link DGS-1210-28MP rev. F1 is a switch with 24 ethernet ports and 4
combo ports, all ports Gbit capable. It is based on a RTL8382 SoC @ 500MHz,
DRAM 128MB and 32MB flash. 24 ethernet ports are 802.3af/at PoE capable
with a total PoE power budget of 370W.
Power over Ethernet:
--------------------
The PSE hardware consists of three BCM59121 PSE chips, serving 8 ports
each. They are controlled by a Nuvoton MCU.
In order to enable PoE, the realtek-poe package is required. It is
installed by default, but currently it requires the manual editing of
/etc/config/poe. Keep in mind that the port number assignment does not
match on this switch, alway 8 ports are in reversed order: 8-1, 16-9 and
24-17.
LEDs and Buttons:
-----------------
On stock firmware, the mode button is supposed to switch the LED indicators
of all port LEDs between Link Activity and PoE status. The currently
selected mode is visualized using the respective LEDs. PoE Max indicates
that the maximum PoE budget has been reached.
Since there is currently no support for this behavior, these LEDs and
the mode button can be used independently.
Serial connection:
------------------
The UART for the SoC (115200 8N1) is available via unpopulated standard
0.1" pin header marked J6. Pin1 is marked with arrow and square.
Pin 1: Vcc 3.3V
Pin 2: Tx
Pin 3: Rx
Pin 4: Gnd
OEM installation from Web Interface:
------------------------------------
1. Make sure you are booting using OEM in image 2 slot. If not, switch to
image2 using the menus
System > Firmware Information > Boot from image2
Tools > reboot
2. Upload image in vendor firmware via Tools > Backup / Upgrade
Firmware > image1
3. Toogle startup image via System > Firmware Information > Boot from
image1
4. Tools > reboot
Other installation methods not tested, but since the device shares the
board with the DGS-1210-28, the following should work:
Boot initramfs image from U-Boot:
---------------------------------
1. Press Escape key during `Hit Esc key to stop autoboot` prompt
2. Press CTRL+C keys to get into real U-Boot prompt
3. Init network with `rtk network on` command
4. Load image with `tftpboot 0x8f000000
openwrt-rtl838x-generic-d-link_dgs-1210-28mp-f-initramfs-kernel.bin`
command
5. Boot the image with `bootm` command
Signed-off-by: Andreas Böhler <dev@aboehler.at>
Wavlink WS-WN572HP3 4G is an 802.11ac
dual-band outdoor router with LTE support.
Specifications;
* Soc: MT7621DAT
* RAM: 128MiB
* Flash: NOR 16MiB GD-25Q128ESIG3
* Wi-Fi:
* MT7613BEN: 5GHz
* MT7603EN: 2.4GHz
* Ethernet: 2x 1GbE
* USB: None - only used internally
* LTE Modem: Quectel EC200T-EU
* UART: 115200 baud
* LEDs:
* 7 blue at the front
* 1 Power
* 2 LAN / WAN
* 1 Status
* 3 RSSI (annotated 4G)
* 1 green at the bottom (4G LED)
* Buttons: 1 reset button
Installation:
* press and hold the reset button while powering on the device
* keep it pressed for ten seconds
* connect to 192.168.10.1 via webbrowser (chromium/chrome works, at
least Firefox 106.0.3 does not)
* upload the sysupgrade image, confirm the checksum, wait 2 minutes
until the device reboots
Revert to stock firmware:
* same as installation but use the recovery image for WL-WN572HP3
Signed-off-by: Jan-Niklas Burfeind <git@aiyionpri.me>
Acked-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Define the load-address for the DTB of all Ubiquiti UniFi devices using
FIT images. From the GPL code we can assume these boards are affected by
the same relocating issue with the vendor bootloader.
Signed-off-by: David Bauer <mail@david-bauer.net>
As the referenced MTD partition is only present in the dts, also move
&slot0 down to the dts files.
Fixes: 64e9b62829 ("mediatek: remove redundant flash entry from dtsi")
Fixes: 7dbac3433f ("mediatek: add support for reyee AX3200-E5")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Splitting-off the common parts of Ruijie RG-EW3200GX PRO and
reyee AX3200-E5 went wrong because the flash descriptiom was kept
also in the dtsi. Remove it there, as flash definition is added by
both board dts files.
Fixes: 7dbac3433f ("mediatek: add support for reyee AX3200-E5")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
1. Drop useless character '0xff' before fake filesystem header.
2. Reduce useless padding to shrink the size of the sysupgrade image.
3. Do not check the size of sysupgrade image. It does not make sense to
check the size of a compressed package.
4. Do not take the size of netgear header into account because it will
not be written to Flash.
5. Use the default lzma compression dictionary parameter '-d24' to get
better performance.
Tested on Netgear R6100
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
This is yet another model of the Ruijie RG-EW3200GX PRO with a slightly
different flash layout, install process is the same.
Specifications:
SoC: MT7622B
RAM: 256MB
Flash: XMC XM25QH128C or Winbond WQ25Q128JVSQ 16MB SPI NOR
Ethernet: 5x1GbE
Switch: MT7531BE
WiFi: 2.4G: MT7622 5G: MT7915AN+MT7975AN
3LEDs: System LED(blue) + Mesh LED(green) + Mesh LED(red)
2Keys: Mesh button + Reset button
UART: Marked J19 on board. 3.3v, 115200n1
Power: 12V 2.5A
Flash instruction:
1. Serve the initramfs.img using a TFTP server with address 10.10.10.3.
2. Interrupt the uboot startup process via UART.
3. Select "System Load Linux to SDRAM via TFTP" item.
4. (important) Back up firmware(mtd7) partitions with:
dd if=/dev/mtd7 of=/tmp/firmware.bin
and then download the firmware.bin image via SCP.
5. Flash the OpenWrt sysupgrade firmware.
Recovery stock firmware:
1. Transfer the firmware.bin image to the device.
2. Flash the image with:
mtd write firmware.bin firmware
Signed-off-by: Alex Hansen <mralexh123@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This device uses an AR8031/AR8033 chip to convert SoC gmac1
RGMII to 1000base-x or sgmii for the SFP fibre cage.
The SFP cage requires phy-mode rgmii-rxid, and without it will not
recieve any packets: ethtool -S sfp rx_fcs_errors will increase when
packets should be being received, but no other _rx counters will change.
Fixes: c77858aa79 ("ramips: mt7621-dts: change phy-mode of gmac1 to rgmii")
Reviewed-by: Robert Marko <robimarko@gmail.com>
Reviewed-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: John Thomson <git@johnthomson.fastmail.com.au>
Set CONFIG_MT6577_AUXADC=y as otherwise reading temperature of the
thermal-zone doesn't work on MT7623 (it does work fine without this
driver on MT7622 and MT7986).
Fixes: f2ae4e2f8c ("mediatek: clean up platform kernel modules")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Use ARTIFACTS to generate initramfs-based factory image of I-O DATA
WN-AX1167GR instead of redundant recipe which generate on
KERNEL_INITRAMFS.
Note:
WN-AX1167GR has 2x OS images on stock firmware.
stock log:
flash manufacture id: c2, device id 20 18
MX25L12805D(c2 2018c220) (16384 Kbytes)
mtd .name = raspi, .size = 0x01000000 (16M) .erasesize = 0x00010000 (64K) .numeraseregions = 0
Creating 10 MTD partitions on "raspi":
0x000000000000-0x000001000000 : "ALL"
0x000000000000-0x000000030000 : "Bootloader"
0x000000030000-0x000000040000 : "Config "
0x000000040000-0x000000050000 : "Factory"
0x000000050000-0x000000060000 : "iNIC_rf"
0x000000060000-0x0000007e0000 : "Kernel"
0x000000800000-0x000000f80000 : "app"
0x000000f90000-0x000000fa0000 : "Key"
0x000000fa0000-0x000000fb0000 : "backup"
0x000000fb0000-0x000001000000 : "storage"
1st image is "Kernel" and 2nd is "app" when booted from 1st image.
In OpenWrt, those 2x partitions are combined to "firmware" with
undefined (empty) areas (0x7e0000-0x7fffff, 0xf80000-0xf8ffff).
The size of an OS image partition is 0x780000 (7680 KiB = 7.5 MiB), so
check-size for initramfs-factory image needs to be called with the size.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
CPU: MediaTek MT7628AN @ 575 MHz
Flash: 16 MB
RAM: 128 MB
Ethernet: 10/100Mbps x 1
Wlan: 300 Mbps
USB: USB 2.0 x 1
LED: red/green x 1
Button: reset x 1
1. Open https://www.hiwifi.wtf/, Get Cloud token and unlock ssh
2. Upload the openwrt firmware to the router via SCP
3. Login the router via SSH
4. Run `mtd -r write path_to_firmware.bin firmware`
I have tested on my device.
- The LED will display RED on power-on, After system start completed, trun GREEN
- Reset button working now. Long press after 5s will reset factory. Short press less 1s will reboot the device
- USB can working under official u-boot
Signed-off-by: Senis John <thank243@gmail.com>
This reverts commit 5429411f73 as upstream
in commit e5f31552674e ("ethernet: fix PTP_1588_CLOCK dependencies") has
changed `PTP_1588_CLOCK` dependency handling in 5.15 kernel.
That currently leads to `CONFIG_NET_DSA_MV88E6XXX=m` in images produced
by buildbots due to `CONFIG_ALL_KMODS=y` config option being used in
those builds, which leads to a broken LAN bridge network on several
devices.
References: https://lists.infradead.org/pipermail/openwrt-devel/2022-December/039950.html
Signed-off-by: Petr Štetiar <ynezz@true.cz>
In light of https://github.com/openwrt/openwrt/issues/11077, switch mvebu
to 5.15 which has been the testing kernel on this target since April - over
half a year.
Run-tested on the following subtargets:
* cortexa9 (Turris Omnia - 03f41b1eb2)
* cortexa72 (MikroTik RB5009UG+S+IN)
Tested-by: Enrico Mioso <mrkiko.rs@gmail.com> [GL-MV1000]
Signed-off-by: Stijn Segers <foss@volatilesystems.org>
should be add/delete or abbreviated add/del
Signed-off-by: Jan-Niklas Burfeind <git@aiyionpri.me>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
The code in dsa.c:rtl83xx_port_enable() was trying to set
vlan_port_tag_sts_ctrl while dealing with differences between SoCs.
However, not only that register has a different address, the register
structure and even the 2-bit value semantic changes for each SoC.
The vlan_port_tag_sts_ctrl field was dropped and converted into a
vlan_port_keep_incoming_tag_set() function that abstracts the different
between SoCs. The macro referencing that register migrated to the SoC
specific c file as it will be privately used by each file.
All magic numbers were converted into macros using BITMASK and
FIELD_PREP.
The vlan_port_tag_sts_ctrl debugfs was dropped for now as it is already
broken for rtl93xx. The best place for SoC specific code might be in each
respective c file and not in if/else clauses.
The final result is:
rtl838x: set ITAG_STS=TAGGED, same as before
rtl839x: set ITAG_STS=TAGGED instead of IGR_P_ITAG_KEEP=0x1, fixing
forwarding of tagged packets
rtl930x: set EGR_ITAG_STS=TAGGED instead of IGR_P_ITAG=0x1, possibly
fixing forwarding of tagged packets
rtl931x: set EGR_ITAG_STS=TAGGED instead of OTPID_KEEP=0x1, possibly
fixing forwarding of tagged packets
Without (EGR_)ITAG_STS=TAGGED, at least for rtl839x, forwarded packets
will drop the vlan tag while packets from the CPU will still have the
correct tag.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
The rtl930x speed status registers require 4 bits to indicate the speed
status. As such, we want to divide by 8. To make things consistent with
the rest of this code, use a bitshift however.
This bug probably won't affect many users yet, as there aren't many
rtl930x switches in the wild yet with more then 10 ports, and thus a
low-impact bugfix.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
[also fix port field extraction]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
The Mikrotik wAP R AC is an outdoor, dual band, dual radio (802.11ac) AP
with a miniPCIe slot for a LTE modem.
The wAP R AC is similar to the wAP AC but with the miniPCIe slot.
The wAP R AC requires installing a LTE modem.
The wAP LTE and wAP LTE6 comes with a LTE modem installed.
See https://mikrotik.com/product/wap_r_ac for more info.
Specifications:
- SoC: Qualcomm Atheros IPQ4018
- CPU: 4x ARM Cortex A7
- RAM: 128MB
- Storage: 16MB NOR flash
- Wireless:
- Built-in IPQ4018 (SoC) 802.11b/g/n 2x2:2, internal antenna
- Built-in IPQ4018 (SoC) 802.11a/n/ac 2x2:2, internal antenna
- Ethernet: Built-in IPQ4018 (SoC, QCA8075) , 2x 1000/100/10 ports
one with 802.3af/at PoE in
- 1x Mini PCI-E port (USB2)
Installation:
Boot the initramfs image via TFTP, then flash the sysupgrade image using
sysupgrade. Details at https://openwrt.org/toh/mikrotik/common.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Swconfig isn't used by this target and can be disabled for
this reason. Airoha doesn't even have an Ethernet driver.
In the future, this target should get a DSA driver.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
