- assume "tcp+udp" if no protcol is specified in rules or redirects (#13422, #13386)
- add support for fwmark matches and mark setting targets
SVN-Revision: 36521
- copy permission of config files to state files to allow access to state info by non root users
- properly handle empty string case when unsetting lists
SVN-Revision: 36518
In my machine, the file is created with arptable_filter before
arp_tables. This can't happen because the former depends on the
latter.
So, instead of rely on wildcards (*.ko), set by hand the files to
be loaded in the correct order.
Signed-off-by: Jonh Wendell <jonh.wendell@oiwifi.com.br>
SVN-Revision: 36512
libiptc.pc depends on libip[4|6]tc.pc, thus all of those need to be
installed.
Should fix collectd build and thus #13146; which should make collectd
appear in snapshots again.
Signed-off-by: Danny Baumann <dannybaumann@web.de>
SVN-Revision: 36509
And while at it, also include a define check for BCM6328, thanks to
Gabor for spotting this.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 36506
Update the numbering of kernel patch for supporting
Netgear WNR2000v3 from 617 to 618.
Signed-off-by: yousong <yszhou4tech@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36498
Fix "Widening multiply-accumulate operation uses wrong value extension"
for 4.7, 4.7-linaro and 4.6-linaro, which backported the broken code to 4.6.
Vanilla 4.6 is unaffected.
Fixes#13420.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 36486
I recently picked up a WNDR3700 to put OpenWRT on, and only after tearing into the box did I find it
was one of the v3 boards, with poor OpenWRT support. This patch should add the board detection and
LED/button control to the broadcom-diag module, and should generate a netgear .chk image that the
bootloader and stock firmware will accept.
The changes to the broadcom-diag module are more than a few lines because the WNDR3700v3 is driving
its LEDs through an HC164 8-bit shift register.
Signed-off-by: Owen Kirby <osk@exegin.com>
SVN-Revision: 36482
Hardcoding channel number to 11 is a bad idea, it may be even not
available on some devices. If there are two single-band radios, the
one for 5GHz doesn't have 11 channel.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 36479
Network connectivity works fine (LAN and WAN).
For GPIOs, only pwr led and the green wan leds are supported for now.
Signed-off-by: Mathieu Olivari <mathieu.olivari@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36459
Add support for TPLINK WR720N v3 which has 4MB flash,
32MB ram, 2 ethernet interfaces, 1 USB 2.0 port.
The patch is mostly a modification from mach-tl-wr703n.c.
GPIO numbers for the slider switch is from mach-tl-mr3020n.c.
Tested on my device and they worked fine.
Signed-off-by: yousong <yszhou4tech@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36456
Only difference between Generic and P1020 is that P1020
enables SMP with two CPUs in the kernel config.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36454
