The device path to the devices changed. Migrate the wifi
configurations from the old path to the new one. This is needed to
migrate Wireless configurations from OpenWrt 23.05 to OpenWrt 24.10.
This script is based on these two files:
target/linux/ramips/mt7621/base-files/etc/hotplug.d/ieee80211/05-wifi-migrate
target/linux/qualcommax/ipq807x/base-files/etc/hotplug.d/ieee80211/05-wifi-migrate
Fixes: 0ef9274721 ("mediatek: filogic: move mt7981 on-SoC blocks to "soc" node in DT")
Fixes: https://github.com/openwrt/openwrt/issues/17174
Link: https://github.com/openwrt/openwrt/pull/17210
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The vendor U-Boot on the Cudy WR3000 assign random mac addresses on boot
and set the 'local-mac-address' property which prevents Openwrt from
assigning the correct address from evmem.
This patch removes the alias for ethernet0 so that U-Boot doesn't add
the property.
Related to: a55ab9e134 ("mediatek: filogic: prevent faulty mac address assignment")
Fixes: https://github.com/openwrt/openwrt/issues/15587
Signed-off-by: Ondřej Niesner <ondra.niesner@seznam.cz>
Link: https://github.com/openwrt/openwrt/pull/17201
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
libbfd feature is not used when building eBPF program, and it makes bpftool fail to build in a clean environment, since binutils in toolchain have libbfd disabled.
Signed-off-by: Eric Long <i@hack3r.moe>
Link: https://github.com/openwrt/openwrt/pull/17073
Signed-off-by: Robert Marko <robimarko@gmail.com>
This is a simple conversion to dts.
68ac3f2cdd states that the 5ghz wifi address is calculated from ART 0
+ 2.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17066
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Specification:
* Mediatek MT7981BA
* 256 MB SPI-NAND
* 512 MB DDR4 RAM
* MT7976CN DBDC AX Wi-Fi
* MediaTek MT7531AE (3x LAN Gigabit ports) + Internal Gbe Phy (1x WAN Gigabit port)
* 4x LED (power, internet, fn, wifi)
* 3x buttons (wps, fn, reset)
* 1x USB 3.0 port
Serial Interface:
* 3 Pins GND, RX, TX
* Settings: 115200, 8N1
Notes:
* The device supports dual boot mode
* Fn led reassigned to wlan 2.4
Flash instruction:
The only way to flash OpenWrt image is to use tftp recovery mode in U-Boot:
1. Configure PC with static IP 192.168.1.2/24 and tftp server.
2. Rename "openwrt-mediatek-filogic-keenetic_kn-3811-squashfs-factory.bin"
to "KN-3811_recovery.bin" and place it in tftp server directory.
3. Connect PC with ethernet port, press the reset button, power up
the device and keep button pressed until status led start blinking.
4. Device will download file from server, write it to flash and reboot.
Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17135
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Enable the busybox feature to save shell command history.
(.apk size increase 0.5 kB)
To prevent flash wear,
* save history only at the exit from a shell session, and
* set /tmp as the default location for the history file. The history
is kept on ramdisk until a reboot, when the history is then lost.
If the user wants to save history onto flash, he can change the location
definition in /etc/profile.d/busybox-history-file.sh
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Link: https://github.com/openwrt/openwrt/pull/17179
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add patch to fix failure to build package/devel/perf when
CONFIG_TARGET_OPTIMIZATION has -O3 enabled with this error:
```
In function 'elf_close',
inlined from 'elf_close' at elf.c:41:6,
inlined from 'elf_find_func_offset_from_file' at elf.c:267:2:
elf.c:45:9: error: 'elf_fd.elf' may be used uninitialized [-Werror=maybe-uninitialized]
45 | elf_end(elf_fd->elf);
| ^~~~~~~~~~~~~~~~~~~~
elf.c: In function 'elf_find_func_offset_from_file':
elf.c:260:23: note: 'elf_fd.elf' was declared here
260 | struct elf_fd elf_fd;
| ^~~~~~
In function 'elf_close',
inlined from 'elf_close' at elf.c:41:6,
inlined from 'elf_find_func_offset_from_file' at elf.c:267:2:
elf.c:46:9: error: 'elf_fd.fd' may be used uninitialized [-Werror=maybe-uninitialized]
46 | close(elf_fd->fd);
| ^~~~~~~~~~~~~~~~~
elf.c: In function 'elf_find_func_offset_from_file':
elf.c:260:23: note: 'elf_fd.fd' was declared here
260 | struct elf_fd elf_fd;
| ^~~~~~
```
Link: https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next.git/commit/?id=fab45b962749
Signed-off-by: Pavel Shirov <nstorm.ahoy166@silomails.com>
Link: https://github.com/openwrt/openwrt/pull/17141
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Create a separate header files fallback-sprom.h
for BCMA and SSB Fallback SPROM Driver
to add function prototypes to fallback-sprom.c as well.
This prevents missing function prototype errors.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/17138
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add NETGEAR_BOARD_ID and NETGEAR_HW_ID to DEVICE_VARS as multiple devices
set them in their recipes, so without them being added to DEVICE_VARS then
simply the value from last recipe that gets evaluated is used and images
are generated with the wrong ID-s.
Link: https://github.com/openwrt/openwrt/pull/17203
Signed-off-by: Robert Marko <robimarko@gmail.com>
Linksys MR7350 is a 802.11ax Dual-band router/AP.
Specifications:
* CPU: Qualcomm IPQ6000 Quad core Cortex-A53(A73) 1.5GHz
* RAM: 512MB of DDR3
* Storage: 256Mb NAND
* Ethernet: 5x1G RJ45 ports (QCA8075)
* WLAN:
* 2.4GHz: Qualcomm QCN5022 2x2 802.11b/g/n/ax 574 Mbps PHY rate
* 5GHz: Qualcomm QCN5052 2x2@80MHz or 802.11a/b/g/n/ac/ax 1201 Mbps PHY rate
* LED-s:
* RGB system led
* USB blue led
* Buttons: 1x Soft reset 1x WPS
* Power: 12V DC Jack
Installation instructions:
Open Linksys Web UI - http://192.168.1.1/ca or http://10.65.1.1/ca depending on your setup.
Login with your admin password. The default password can be found on a sticker under the device.
To enter into the support mode, click on the “CA” link and the bottom of the page.
Open the “Connectivity” menu and upload the squash-factory image with the “Choose file” button.
Click start. Ignore all the prompts and warnings by click “yes” in all the popups.
The Wifi radios are turned off by default. To configure the router, you will need to connect your computer to the LAN port of the device.
Then you would need to write openwrt to the other partition for it to work
- First Check booted partition:
fw_printenv -n boot_part
- Change the partition:
fw_setenv boot_part 1
or
fw_setenv boot_part 2
depending on the current partition
- Then install Openwrt to the other partition if booted in slot 1:
mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq60xx-linksys_mr7350-squashfs-factory.bin alt_kernel
- If in slot 2:
mtd -r -e kernel -n write openwrt-qualcommax-ipq60xx-linksys_mr7350-squashfs-factory.bin kernel
Co-Authored-by: Chukun Pan <amadeus@jmu.edu.cn>
Co-Authored-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Vladyslav Andreichykov <vladdrako007@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/14807
Signed-off-by: Robert Marko <robimarko@gmail.com>
Userspace regulator consumer is rather usefull so enable it for ipq60xx
as well and remove from ipq807x only kernel config.
Link: https://github.com/openwrt/openwrt/pull/14807
Signed-off-by: Robert Marko <robimarko@gmail.com>
47b54cf5a4b6 types: introduce `ucv_array_sort_r()` and `ucv_object_sort_r()`
efeb57806552 types, vm: refactor usage of global variables
f9d2faf67de6 vm: reset signals when freeing VM
4e86847d802d lib: utilize `ucv_array_sort_r()` and `ucv_object_sort_r()`
c71444ea301f types: ucv_resource_create(): rename `typename` parameter to `type`
373df7299c79 nl80211: properly support split_wiphy_dump for single phys
9bcd25f54708 lexer: Preserve keyword, regexp flags until processing non-comment tokens
0a7ff4715cb8 main: pretty-print `-p` output by default
4c3d5b469156 struct: Add new buffer API for incremental packing/unpacking
efc4122124cb struct: do not use global variables for caching types
Fixes: https://github.com/jow-/ucode/issues/248
Fixes: https://github.com/jow-/ucode/issues/250
Fixes: https://github.com/efahl/owut/issues/25
Link: https://github.com/openwrt/openwrt/pull/17191
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add support for FORESEE F35SQA001G SPI NAND.
Similar to F35SQA002G, but differs in capacity.
Datasheet:
- https://cdn.ozdisan.com/ETicaret_Dosya/704795_871495.pdf
Tested on Xiaomi AX3000T flashed with OpenWRT.
Signed-off-by: Bohdan Chubuk <chbgdn@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/16915
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Specifications:
SoC: Qualcomm IPQ6000 1.5GHz
RAM: NTCC256M16ER-EK 512MiB
Flash: W29N01HZSINA 128MiB
ETH: QCA8075 (3x LAN, 1x WAN)
WLAN1: 2.4GHz 802.11b/g/n/ax 2x2
WLAN2: 5GHz 802.11a/n/ac/ax 2x2
Power: DC 12V 1.5A
Button: Reset, Wps
USB: 1x 2.0
Flash instructions:
1. Download the initramfs image, rename it to
initramfs.itb, host it with the tftp server.
2. Interrupt U-Boot and run these commands:
tftpboot initramfs.itb
bootm
3. After openwrt boots up, use scp or luci web
to upload sysupgrade.bin to upgrade.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/15940
Signed-off-by: Robert Marko <robimarko@gmail.com>
Contains following updates:
* ipq8074: add TP-Link_deco-x80-5g BDF
* ipq6018: add BDF for Qihoo 360V6
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/15940
Signed-off-by: Robert Marko <robimarko@gmail.com>
1006 and 5006 are defaults that get set based on the calibration data.
There's no need to explicitly specify them.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17128
Signed-off-by: Robert Marko <robimarko@gmail.com>
Keenetic KN-3211 is a 2.4 Ghz band 11n (Wi-Fi 4) Wi-Fi repeater, based on MT7628AN.
Specification:
- System-On-Chip: MT7628AN
- CPU/Speed: 575 MHz
- Flash-Chip: Winbond w25q256
- Flash size: 32768 KiB
- RAM: 64 MiB
- 1x 10/100 Mbps Ethernet
- 2x external, non-detachable antennas
- UART (J1) header on PCB (115200 8n1)
- Wireless No1 (2T2R): SoC Built-in 2.4 GHz 802.11bgn
- 3x LED, 1x button, 1x mode switch
Notes:
- The device supports dual boot mode
- The firmware partitions were concatenated into one
- The status button has been reassigned as the WPS button.
Flash instruction:
This device doesn't support sysupgrade, so the only way to flash OpenWrt image
is to use tftp recovery mode in U-Boot:
1. Configure PC with static IP 192.168.1.2/24 and tftp server.
2. Rename "openwrt-ramips-mt76x8-keenetic_kn-3211-squashfs-factory.bin"
to "KN-3211_recovery.bin" and place it in tftp server directory.
3. Connect PC with the ethernet port, press the reset button, power up
the router and keep button pressed until power led starts blinking.
4. Router will download file from server, write it to flash and reboot.
Signed-off-by: Ivan Davydov <lotigara@lotigara.ru>
Link: https://github.com/openwrt/openwrt/pull/17080
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Change the cron log level in init script from 5 to 7
in order to match previous log behavior and to avoid
log spam every minute.
Busybox cron only uses levels 5,7,8, where 5 is debug and
7 and 8 are normal logging. Use 7 as default.
(Fun note: this is needed because upstream corrected an
ancient bug in their own log level handling and now 5 actually
means something.)
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Link: https://github.com/openwrt/openwrt/pull/17107
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add a patch to fix non-x86 builds, refresh patches and update/fix the
configuration as described in 98b09ba250 (cited here for future reference).
Config refresh:
Refresh commands, run after busybox is first built once:
cd package/utils/busybox/config/
../convert_menuconfig.pl ../../../../build_dir/target-arm_cortex-a15+neon-vfpv4_musl_eabi/busybox-default/busybox-1.37.0
cd ..
./convert_defaults.pl ../../../build_dir/target-arm_cortex-a15+neon-vfpv4_musl_eabi/busybox-default/busybox-1.37.0/.config > Config-defaults.in
Manual edits needed after config refresh:
* Config-defaults.in: OpenWrt config symbol IPV6 logic applied to
BUSYBOX_DEFAULT_FEATURE_IPV6
* Config-defaults.in: OpenWrt config TARGET_bcm53xx logic applied to
BUSYBOX_DEFAULT_TRUNCATE (commit 547f1ec)
* Config-defaults.in: OpenWrt logic applied to
BUSYBOX_DEFAULT_LOGIN_SESSION_AS_CHILD (commit dc92917)
* Config-defaults.in: correct the default ports that get reset
BUSYBOX_DEFAULT_FEATURE_HTTPD_PORT_DEFAULT 80
BUSYBOX_DEFAULT_FEATURE_TELNETD_PORT_DEFAULT 23
* config/editors/Config.in: Add USE_GLIBC dependency to
BUSYBOX_CONFIG_FEATURE_VI_REGEX_SEARCH (commit f141090)
* config/shell/Config.in: change at "Options common to all shells" the conditional symbol
SHELL_ASH --> BUSYBOX_CONFIG_SHELL_ASH
(discussion in http://lists.openwrt.org/pipermail/openwrt-devel/2021-January/033140.html
Apparently our script does not see the hidden option while
prepending config options with "BUSYBOX_CONFIG_" which leads to a
missed dependency when the options are later evaluated.)
* Edit a few Config.in files by adding quotes to sourced items in
config/Config.in, config/networking/Config.in and config/util-linux/Config.in (commit 1da014fcca)
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
[rebased with the change download line commit]
[corrected version in the refresh example in commit message]
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Link: https://github.com/openwrt/openwrt/pull/17107
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
- fix variable references for ft key
- add r0kh and r1kh if ft_generate_local is not set (logic inversion bug)
Signed-off-by: Felix Fietkau <nbd@nbd.name>
As discussed in the previous OpenWrt meeting the easiest way to have
regular builds of packages on the video feed without adding additional
complexity is by enabling the video feed by default.
If that slows down the buildbots beyond being useful we can always
disable it again and find another way to only sporadically build
packages of the video feed.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The internal hostapd version cannot be built with EAP-pwd support, so
enable it only for the SSL variants.
Fixes: #17163
Fixes: 6365316fab ("hostapd: add ubus support for wired driver")
Link: https://github.com/openwrt/openwrt/pull/17164
Signed-off-by: Robert Marko <robimarko@gmail.com>
mkits.sh creates a root.*.pagesync file with padding, which is global, and
the generated .its files reference it. Since dtc reads this file, it must
not run at the same time as mkits.sh
Fixes generating itb images with broken rootfs.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
3da6c104f0f5 database: use APK_DB_LAYER_ROOT in more places
5437e3abada1 audit: add usr/lib/apk to the list of protected paths under --full
de9baf912245 change default db location to /usr, but detect and use /lib if exists
218fdaa1a1a2 context: close root_fd on free
d33294236cb4 database: add support for only-when-modified trigger paths
36935db0ef3b package: fix memfd_create warnings on Linux kernels < 6.7
1c3fc36051a3 blob: add and use apk_blob_trim_{start,end}
af5f9e3f93b0 pkg: fix v3 package size setting to installeddb
9428e34694c8 version: allow --check and --test to work without database
4b4add5326a8 test: fix unit test registration function to be unique
eac18cb200d4 test: add testlib.sh for user tests
20dae205b006 mkpkg: fix creation of package with hardlinks
7bdecdca6a95 pkg: only allow tags in world and some commands
76de228bcc0b commit: show tags of world constrains
9a1b1cf68420 test: use testlib for solver.sh
99fc2a2a5efc test: remove dependency on GNU tar
6927746b9a10 Revert usrmerge/LFS related changes to apk used paths
5d287a9b06e9 apk-tools-3.0.0_pre5
8d93a79fb895 mkpkg: fix hardlink on big-endian system
Link: https://github.com/openwrt/openwrt/pull/17148
Signed-off-by: Robert Marko <robimarko@gmail.com>
Recent changes to BuildBot config moved the kmods to a dedicated
directory and dropped them from the packages dir. This was needed as
both OPKG and APK gets confused if both entry are present.
To fix this, unconditionally append the kmod feed line if
CONFIG_BUILDBOT is enabled.
Fixes: #17146
Link: https://github.com/openwrt/openwrt/pull/17151
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Introduce package flag MESON_USE_STAGING_PYTHON which allows packages
to be built with the OpenWrt-built python3/host instead of relying on the
buildhost's Python distribution.
This is useful for packages using Meson which require additional Python
modules during build.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Rename jffs2reset to factoryreset. Convert all scripts to using the new command
line. Print a deprecation notice when jffs2reset is invoked.
49d36ba jffs2reset: rename to factoryreset
b135064 jffs2reset: print deprecation message
Signed-off-by: John Crispin <john@phrozen.org>
The boot LED on OpenWrt One is PWM driven and sets the pattern trigger as the
default inside its devicetree.
Signed-off-by: John Crispin <john@phrozen.org>
Add an ucode based re-implementation of the shell script based wifi code.
The new code is jsonschema driven. The code has been refactored into several
files making it easier to follow.
The new scripts are also way faster than the previous sh implementation.
The new code is currently opt-in via WIFI_SCRIPTS_UCODE and defaults to
EXPERIMENTAL.
Signed-off-by: John Crispin <john@phrozen.org>
Add an ucode based re-implementation of iwinfo. The tool behaves like the old
one with a few minor output differences. It is now possible to add -j to any
command resulting in JSON output.
The new code is currently opt-in via WIFI_SCRIPTS_UCODE and defaults to
EXPERIMENTAL.
Signed-off-by: John Crispin <john@phrozen.org>
b0b5d93 Merge pull request #234 from IdWV/fs
60e7a88 Merge pull request #232 from sebastianertz/lib-digest
1752779 digest: implement compile time option to exclude less common algorithms
c7268a1 ci: include libmd in MacOS CI builds
fcb6f70 lib: introduce digest library
1323a27 Merge pull request #246 from jow-/fix-upvalue-resolve
ed5ce8f types: resolve upvalue values in arrays and objects
a6e0641 vm: resolve upvalues before pushing them onto the stack
ef1baab ci: drop OpenWrt tests for now
63e18ea fs: eliminate the usage of global variables
b1bd7b5 types: add ucv_resource_create() helper
3408edf Merge pull request #244 from nbd168/nl80211
8af77e7 nl80211: add new attributes for multi-radio support
1423ad7 nl80211: cover extended feature and EHT rate info attributes
ee1d6d8 Merge pull request #237 from sebastianertz/math
4b18a9b Merge pull request #213 from jow-/improve-vector-macros
1f022c0 math: removed global variable for thread safety
e5fe6b1 treewide: refactor vector usage code
20307ee utils: improve vector utilities
aa18952 Merge pull request #241 from jow-/socket-local-fanout-decl
79ccd9c socket: provide local definition of `struct fanout_args`
402280d Merge pull request #239 from jow-/safe-insert-during-obj-iteration
07afe96 Merge pull request #240 from jow-/stricter-number-conversion
736d450 types: fix potential use after free on adding keys during iteration
4134e71 vallist: more thoroughly check for trailing garbage after numeric string
9cf53dd Merge pull request #226 from jow-/lexer-improvements
2b2e732 lexer: make api functions public
855854f lexer: emit comment and template statement block tokens
328a50f lexer: improve token position reporting
fa22732 Merge pull request #225 from jow-/compiler-fix-keyword-property-labels-after-spread
6e88c62 Merge pull request #224 from jow-/lib-fs-readline-leak
94d1211 compiler: properly treat property names after spread expressions
67cd123 fs: fix potential memory leak on i/o errors in .read()
Signed-off-by: John Crispin <john@phrozen.org>
Use and alternate ubus object when the config contains "driver=wired". This
commit is in preparation of the ieee8021x-wired daemon.
Signed-off-by: John Crispin <john@phrozen.org>
This allows a radius server to send AVPs for client rate control inside the
accept message. Further add the ratelimits to the sta-authorized ubus
notification.
Signed-off-by: John Crispin <john@phrozen.org>
* add a UCI option to disable all LEDs.
* add an init.d parameter to blink all LEDs
* add on/off parameters to init.d
Signed-off-by: John Crispin <john@phrozen.org>
