Commit Graph

20064 Commits

Author SHA1 Message Date
Dirk Buchwalder
a36fc589fe ipq807x: add Edimax CAX1800
Edimax CAX1800 is a 802.11 ax dual-band AP
with PoE. AP can be ceiling or wall mount.

Specifications:

    •     CPU: Qualcomm IPQ8070A Quad core Cortex-A53 1.4GHz
    •     RAM: 512MB of DDR3
    •     Storage: 128MB NAND (contains rootfs) / 8MB NOR (contains art and uboot-env)
    •     Ethernet: 1x 1G RJ45 port (QCA8072) PoE
    •     WLAN:
          2.4GHz: Qualcomm QCN5024 2x2 802.11b/g/n/ax 574 Mbps PHY rate
          5GHz: Qualcomm QCN5054 2x2 802.11a/b/g/n/ac/ax 1201 PHY rate

    •     LEDs:
          3 x GPIO-controlled System-LEDs
          (form one virtual RGB System-LED)
            black_small_square  Buttons: 1x soft reset
            black_small_square  Power: 12V DC jack or PoE (802.3af )

        An unpopulated serial header is onboard.
        RX/TX is working, bootwait is active, secure boot is not enabled.

        SSH can be activated in the stock firmware, but it drops only
        to a limited shell .

        Installation Instructions:

            black_small_square obtain serial access
            black_small_square stop auto boot

            black_small_square tftpboot the initramfs image (serverip is set to 192.168.99.8 in uboot)
            black_small_square bootm

            black_small_square copy openwrt-ipq807x-generic-edimax_cax1800-squashfs-nand-factory.ubi
	      to the device
            black_small_square write the image to the NAND:
            black_small_square cat /proc/mtd and look for rootfs partition (should be mtd0)
            black_small_square ubiformat /dev/mtd0 -f -y  openwrt-ipq807x-generic-edimax_cax1800-squashfs-
              nand-factory.ubi
            black_small_square reboot

	Note: Device is not using dual partitioning (NAND contains other partitions
        with different manufacture data etc.)
	Draytek VigorAP 960C and Lancom LW-600 both look similar, but I haven't checked them.

Signed-off-by: Dirk Buchwalder <buchwalder@posteo.de>
2023-01-16 12:42:23 +01:00
Zhijun You
8253cb2de5 ipq807x: add Redmi AX6
Redmi AX6 is a budget 802.11ax dual-band router/AP

Specifications:
* CPU: Qualcomm IPQ8071A Quad core Cortex-A53 1.4GHz
* RAM: 512MB of DDR3
* Storage: 128MB NAND
* Ethernet: 4x1G RJ45 ports (QCA8075)
* WLAN:
	* 2.4GHz: Qualcomm QCN5024 2x2 802.11b/g/n/ax 574 Mbps PHY rate
	* 5GHz: Qualcomm QCN5054 4x4@80MHz or 2x2@160MHz 802.11a/b/g/n/ac/ax 2402 PHY rate
* LEDs:
	* System (Blue/Yellow)
	* Network (Blue/Yellow)
*Buttons: 1x soft reset
*Power: 12V DC jack

Installation instructions:

Obtaining SSH access is mandatory
https://openwrt.org/inbox/toh/xiaomi/xiaomi_redmi_ax6_ax3000#ssh_access

Installation is done by the ubiformat method, through SSH:
1. Open an SSH shell to the router
2. Copy the file openwrt-ipq807x-generic-redmi_ax6-initramfs-factory.ubi to the /tmp directory
3. Check which rootfs partition is your router booted in (0 = rootfs | 1 = rootfs_1):
nvram get flag_boot_rootfs

4. Find the rootfs and rootfs_1 mtd indexes respectively:
cat /proc/mtd
Please confirm if mtd12 and mtd13 are the correct indexes from above!

5. Use the command ubiformat to flash the opposite mtd with UBI image:

If nvram get flag_boot_rootfs returned 0:
ubiformat /dev/mtd13 -y -f /tmp/openwrt-ipq807x-generic-redmi_ax6-initramfs-factory.ubi && nvram set flag_boot_rootfs=1 && nvram set flag_last_success=1 && nvram commit

otherwise:
ubiformat /dev/mtd12 -y -f /tmp/openwrt-ipq807x-generic-redmi_ax6-initramfs-factory.ubi && nvram set flag_boot_rootfs=0 && nvram set flag_last_success=0 && nvram commit

6. Reboot the device by:
reboot

Previous commands flashed an ubinized OpenWrt initramfs that will serve as the intermediate step
since OpenWrt uses unified rootfs in order to fully utilize NAND and provide enough space for packages.
Continue in order to pernamently flash OpenWrt:

7. SSH into OpenWrt from one of the LAN ports
8. Copy the file openwrt-ipq807x-generic-redmi_ax6-squashfs-sysupgrade.bin to the /tmp directory
9. Sysupgrade the device:
sysupgrade -n /tmp/openwrt-ipq807x-generic-redmi_ax6-squashfs-sysupgrade.bin

Device will reboot with OpenWrt, and then sysupgrade can be used to upgrade the device when desired.

Signed-off-by: Zhijun You <hujy652@gmail.com>
2023-01-16 12:42:23 +01:00
Robert Marko
8364f08164 ipq807x: add Xiaomi AX3600
Xiaomi AX3600 is a budget 802.11ax dual-band router/AP.
Specifications:
* CPU: Qualcomm IPQ8071A Quad core Cortex-A53 1.4GHz
* RAM: 512MB of DDR3
* Storage: 256MB of parallel NAND
* Ethernet: 4x1G RJ45 ports (QCA8075) with 1x status LED per port
* WLAN:
	* PCI based Qualcomm QCA9889 1x1 802.11ac Wawe 2 for IoT
	* 2.4GHz: Qualcomm QCN5024 2x2 802.11b/g/n/ax 574 Mbps PHY rate
	* 5GHz: Qualcomm QCN5054 4x4@80MHz or 2x2@160MHz 802.11a/b/g/n/ac/ax 2402 PHY rate
* LED-s:
	* System (Blue and Yellow)
	* IoT (Blue)
	* Network (Blue and Yellow)
* Buttons: 1x Soft reset
* Power: 12V DC Jack

Installation instructions:

Obtaining SSH access is mandatory
https://openwrt.org/inbox/toh/xiaomi/xiaomi_ax3600#obtain_ssh_access

Installation is done by the ubiformat method, through SSH:
1. Open an SSH shell to the router
2. Copy the file openwrt-ipq807x-generic-xiaomi_ax3600-initramfs-factory.ubi to the /tmp directory
3. Check which rootfs partition is your router booted in (0 = rootfs | 1 = rootfs_1):
nvram get flag_boot_rootfs

4. Find the rootfs and rootfs_1 mtd indexes respectively:
cat /proc/mtd
Please confirm if mtd12 and mtd13 are the correct indexes from above!

5. Use the command ubiformat to flash the opposite mtd with UBI image:

If nvram get flag_boot_rootfs returned 0:
ubiformat /dev/mtd13 -y -f /tmp/openwrt-ipq807x-generic-xiaomi_ax3600-initramfs-factory.ubi -s 2048 -O 2048 && nvram set flag_boot_rootfs=1 && nvram set flag_last_success=1 && nvram commit

otherwise:
ubiformat /dev/mtd12 -y -f /tmp/openwrt-ipq807x-generic-xiaomi_ax3600-initramfs-factory.ubi -s 2048 -O 2048 && nvram set flag_boot_rootfs=0 && nvram set flag_last_success=0 && nvram commit

6. Reboot the device by:
reboot

Previous commands flashed an ubinized OpenWrt initramfs that will serve as the intermediate step
since OpenWrt uses unified rootfs in order to fully utilize NAND and provide enough space for packages.
Continue in order to pernamently flash OpenWrt:

7. SSH into OpenWrt from one of the LAN ports
8. Copy the file openwrt-ipq807x-generic-xiaomi_ax3600-squashfs-sysupgrade.bin to the /tmp directory
9. Sysupgrade the device:
sysupgrade -n /tmp/openwrt-ipq807x-generic-xiaomi_ax3600-squashfs-sysupgrade.bin

Device will reboot with OpenWrt, and then sysupgrade can be used to upgrade the device when desired.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Robert Marko <robimarko@gmail.com>
2023-01-16 12:42:23 +01:00
Robert Marko
2558e7b443 kernel: add Qualcomm NSS dataplane ethernet driver
Qualcomm NSS-DP is as its name says Qualcomms ethernet driver for the NSS
subsystem (Networking subsystem) built-into various Qualcomm SoCs.

It has 2 modes of operation:
* Without NSS FW and rest of code required for offloading

This is the one that we will use as the amount of kernel patching required
for NSS offloading and the fact that its not upstreamable at all makes it
unusable for us.

Driver in this mode is rather basic, it currently only offers NAPI GRO
(Added by us as part of the fixup) and basically relies on the powerfull
CPU to get good throughput.

* With NSS FW and rest of code required for offloading

In this mode, driver just registers the interfaces and hooks them into
NSS-ECM to allow offloading.
This mode is not viable for use in OpenWrt due to reasons already described
above.

This driver is required for ipq807x to have wired networking until a better
one is available, so lets add the fixed-up version for 5.15 for now.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2023-01-16 12:42:23 +01:00
Robert Marko
c608f70325 kernel: add Qualcomm SSDK driver
Qualcomm SSDK is driver for Qualcomm Atheros switches and PHY-s.

It is quite complicated and used by rest of the Qualcomm SDK stack for
anything switch or PHY related.

It is required for IPQ807x support as currently, there is no better driver
for the built-in switch or UNIPHY.

So, lets add the fixed-up version that supports kernel 5.15 for use on
ipq807x target until a better driver is available.

Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Signed-off-by: Robert Marko <robimarko@gmail.com>
2023-01-16 12:42:23 +01:00
Robert Marko
35f28f2838 mac80211: add ath11k AHB support
This is the follow up to the PCI support commit now providing support for
AHB variant as well, though currently only for ipq807x as that is only
OpenWrt supported SoC ath11k supports as well.

Currently, we are disabling coldboot calibration on ipq807x as it does not
work, there is a remoteproc bug that makes it come late out of reset so
disable coldboot until that is fixed.

Also, as ath11k is quite memory hungry, we are introducing a config option
to use the limits for 512MB of RAM, similar to what QCA does downstream but
in way simpler and cleaner way so that 512MB save some RAM.
512MB profile is also set as the default for now.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2023-01-16 12:42:23 +01:00
Robert Marko
b5f32064ed ipq807x: add Qualcomm Atheros IPQ807x target
Qualcomm Atheros IPQ807x is a modern WiSoC featuring:
* Quad Core ARMv8 Cortex A-53
	* @ 2.2 GHz (IPQ8072A/4A/6A/8A) Codename Hawkeye
	* @ 1.4 GHz (IPQ8070A/1A) Codename Acorn
* Dual Band simultaneaous IEEE 802.11ax
	* 5G: 8x8/80 or 4x4/160MHz (IPQ8074A/8A)
	* 5G: 4x4/80 or 2x2/160MHz (IPQ8071A/2A/6A)
	* 5G: 2x2/80MHz (IPQ8070A)
	* 2G: 4x4/40MHz (IPQ8072A/4A/6A/8A)
	* 2G: 2x2/40MHz (IPQ8070A/1A)
* 1x PSGMII via QCA8072/5 (Max 5x 1GbE ports)
* 2x SGMII/USXGMII (1/2.5/5/10 GbE) on Hawkeye
* 2x SGMII/USXGMII (1/2.5/5 GbE) on Acorn
* DDR3L/4 32/16 bit up to 2400MT/s
* SDIO 3.0/SD card 3.0/eMMC 5.1
* Dual USB 3.0
* One PCIe Gen2.1 and one PCIe Gen3.0 port (Single lane)
* Parallel NAND (ONFI)/LCD
* 6x QUP BLSP SPI/I2C/UART
* I2S, PCM, and TDMA
* HW PWM
* 1.8V configurable GPIO
* Companion PMP8074 PMIC via SPMI (GPIOS, RTC etc)

Note that only v2 SOC models aka the ones ending with A suffix are
supported, v1 models do not comply to the final 802.11ax and have
lower clocks, lack the Gen3 PCIe etc.

SoC itself has two UBI32 cores for the NSS offloading system, however
currently no offloading is supported.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2023-01-16 12:42:23 +01:00
Robert Marko
4f592fb819 mac80211: ath11k: hack for multiple card support
This is a temporary workaround for supporting multiple cards or AHB+PCI.

There is ongoing upstream work to properly support this based of
advertised FW features, but that is still ongoing.

This is only supported on QCN9074 cards due to FW limitation, so HW ID
is checked in order to prevent breaking QCA6390 and other popular cards.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2023-01-16 12:42:23 +01:00
Robert Marko
af6da88814 firmware: add ath11k-firmware package
Package ath11k firmware for AHB devices as well as QCN9074 which is a non
consumer card targeted as a companion for QCA WiSoC-s.

linux-firmware is always out of date for these, so fetch them from Kalle-s
repo like we do for ath10k.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2023-01-16 12:42:23 +01:00
Harm Berntsen
09f313bfd7 ramips: mt7621: Add Arcadyan WE420223-99 support
The Arcadyan WE420223-99 is a WiFi AC simultaneous dual-band access
point distributed as Experia WiFi by KPN in the Netherlands. It features
two ethernet ports and 2 internal antennas.

Specifications
--------------
SOC   : Mediatek MT7621AT
ETH   : Two 1 gigabit ports, built into the SOC
WIFI  : MT7615DN
BUTTON: Reset
BUTTON: WPS
LED   : Power (green+red)
LED   : WiFi (green+blue)
LED   : WPS (green+red)
LED   : Followme (green+red)
Power : 12 VDC, 1A barrel plug

Winbond variant:
RAM   : Winbond W631GG6MB12J, 1GBIT DDR3 SDRAM
Flash : Winbond W25Q256JVFQ, 256Mb SPI
U-Boot: 1.1.3 (Nov 23 2017 - 16:40:17), Ralink 5.0.0.1

Macronix variant:
RAM   : Nanya NT5CC64M16GP-DI, 1GBIT DDR3 SDRAM
Flash : MX25l25635FMI-10G, 256Mb SPI
U-Boot: 1.1.3 (Dec  4 2017 - 11:37:57), Ralink 5.0.0.1

Serial
------
The serial port needs a TTL/RS-232 3V3 level converter! The Serial
setting is 57600-8-N-1. The board has an unpopulated 2.54mm straight pin
header.

The pinout is: VCC (the square), RX, TX, GND.

Installation
------------
See the Wiki page [1] for more details, it comes down to:

1. Open the device, take off the heat sink
2. Connect the SPI flash chip to a flasher, e.g. a Raspberry Pi. Also
   connect the RESET pin for stability (thanks @FPSUsername for reporting)
3. Make a backup in case you want to revert to stock later
4. Flash the squashfs-factory.trx file to offset 0x50000 of the flash
5. Ensure the bootpartition variable is set to 0 in the U-Boot
   environment located at 0x30000

Note that the U-Boot is password protected, this can optionally be
removed. See the forum [2] for more details.

MAC Addresses(stock)
--------------------
+----------+------------------+-------------------+
| use      | address          | example           |
+----------+------------------+-------------------+
| Device   | label            | 00:00:00:11:00:00 |
| Ethernet | + 3              | 00:00:00:11:00:03 |
| 2g       | + 0x020000f00001 | 02:00:00:01:00:01 |
| 5g       | + 1              | 00:00:00:11:00:01 |
+----------+------------------+-------------------+

The label address is stored in ASCII in the board_data partition

Notes
-----
- This device has a dual-boot partition scheme, but OpenWRT will claim
  both partitions for more storage space.

Known issues
------------
- 2g MAC address does not match stock due to missing support for that in
  macaddr_add
- Only the power LED is configured by default

References
----------
[1] https://openwrt.org/inbox/toh/arcadyan/astoria/we420223-99
[2] https://forum.openwrt.org/t/adding-openwrt-support-for-arcadyan-we420223-99-kpn-experia-wifi/132653

Acked-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: Harm Berntsen <git@harmberntsen.nl>
2023-01-15 13:41:02 +01:00
Vincent Tremblay
9e4ede8344 ipq40xx: add support for Linksys WHW03 V2
SOC:             Qualcomm IPQ4019
WiFi 1:          QCA4019 IEEE 802.11b/g/n
WiFi 2:          QCA4019 IEEE 802.11a/n/ac
WiFi 3:          QCA8888 IEEE 802.11a/n/ac
Bluetooth:       Qualcomm CSR8811 (A12U)
Zigbee:          Silicon Labs EM3581 NCP + Skyworks SE2432L
Ethernet:        Qualcomm Atheros QCA8072 (2-port)
Flash 1:         Mactronix MX30LF4G18AC-XKI
RAM (NAND):      SK hynix H5TC4G63CFR-PBA (512MB)
LED Controller:  NXP PCA9633 (I2C)
Buttons:         Single reset button (GPIO).

- The three WiFis were fully tested and are configured with the same settings as in the vendor firmware.
- The specific board files were submitted to the ATH10k mailing list but I'm still waiting for a reply. They can be removed once they are approved upstream.
- Two ethernet ports are accessible on the device. By default one is configured as WAN and the other one is LAN. They are fully working.

Bluetooth:
========
- Fully working with the following caveats:
  - RFKILL need to be enabled in the kernel.
  - An older version of bluez is needed as bccmd is needed to configure the chip.

Zigbee:
======
- The spidev device is available in the /dev directory.
- GPIOs are configured the same way as in the vendor firmware.
- Tests are on-going. I am working on getting access to the Silicon Labs stack to validate that it is fully working.

Installation:
=========
The squash-factory image can be installed via the Linksys Web UI:
1. Open "http://192.168.1.1/ca" (Change the IP with the IP of your device).
2. Login with your admin password.
3. To enter into the support mode, click on the "CA" link and the bottom of the page.
4. Open the "Connectivity" menu and upload the squash-factory image with the "Choose file" button.
5. Click start. Ignore all the prompts and warnings by click "yes" in all the popups.

The device uses a dual partition mechanism. The device automatically revert to the previous partition after 3 failed boot attempts.
If you want to force the previous firmware to load, you can turn off and then turn on the device for 2 seconds, 3 times in a row.

It can also be done via TFTP:
1. Setup a local TFTP server and configure its IP to 192.168.1.100.
2. Rename your image to "nodes_v2.img" and put it to the TFTP root of your server.
3. Connect to the device through the serial console.
4. Power on device and press enter when prompted to drop into U-Boot.
5. Flash the partition of your choice by typing "run flashimg" or "run flashimg2".
6. Once flashed, enter "reset" to reboot the device.

Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Vincent Tremblay <vincent@vtremblay.dev>
2023-01-15 12:55:38 +01:00
Marcin Gajda
700c47a5f6 ipq40xx: Add support ZTE MF18A
Light and small router ( In Poland operators sells together with MC7010 outdoor modem to provide WIFI inside home).
Device specification

SoC Type: Qualcomm IPQ4019
RAM: 256 MiB
Flash: 128 MiB SPI NAND (Winbond W25N01GV)
ROM: 2MiB SPI Flash (GD25Q16)
Wireless 2.4 GHz (IP4019): b/g/n, 2x2
Wireless 5 GHz (QCA9982): a/n/ac, 3x3
Ethernet: 2xGbE (WAN/LAN1, LAN2)
USB ports: No
Button: 2 (Reset/WPS)
LEDs: 3 external leds: Power (blue) , WiFI (blue and red), SMARTHOME (blue and red) and 1 internal (blue) -- NOTE: Power controls all external led (if down ,all others also not lights even signal is up)
Power: 5VDC, 2,1A via USB-C socket
Bootloader: U-Boot
On board ZWave and Zigbee (EFR32 MG1P232GG..)  modules ( not supported by orginal software )
Installation

 1.Open MF18A case by ungluing rubber pad under the router and unscrew screws, and connect to serial console port,
   with the following pinout, starting from pin 1, which is the topmost pin when the board is upright (reset button on the bottom) :

    VCC (3.3V). Do not use unless you need to source power for the converer from it.
    TX
    RX
    GND

    Default port configuration in U-boot as well as in stock firmware is 115200-8-N-1.

 2.Place OpenWrt initramfs image for the device on a TFTP in the server's root. This example uses Server IP: 192.168.0.2

 3.Connect TFTP server to RJ-45 port (WAN/LAN1).

 4.Power on MF18A , stop in u-Boot (using ESC button) and run u-Boot commands:
    setenv serverip 192.168.0.2
    setenv ipaddr 192.168.0.1
    set fdt_high 0x85000000
    tftpboot 0x84000000 openwrt-ipq40xx-generic-zte_mf18a-initramfs-fit-zImage.itb
    bootm 0x84000000

 5.Please make backup of original partitions, if you think about revert to stock, specially mtd8 (Web UI) and mtd9 (rootFS). Use /tmp as temporary storage and do:

WEB PARITION

cat /dev/mtd8 > /tmp/mtd8.bin
scp /tmp/mtd8.bin root@YOURSERVERIP:/
rm /tmp/mtd8.bin
ROOT PARITION

cat /dev/mtd9 > /tmp/mtd9.bin
scp /tmp/mtd9.bin root@YOURSERVERIP:/
rm /tmp/mtd9.bin

If you are sure ,that you want to flash openwrt, from uBoot, before bootm, clean rootfs partition with command:
nand erase 0x1800000 0x1D00000

 6.Login via ssh or serial and remove stock partitions (default IP 192.168.1.1):
ubiattach -m 9 # it could return error if ubi was attached before or rootfs part was erased before
ubirmvol /dev/ubi0 -N ubi_rootfs # it could return error if rootfs part was erased before
ubirmvol /dev/ubi0 -N ubi_rootfs_data # some devices doesn't have it

 7. Install image via :
sysupgrade -n /tmp/openwrt-ipq40xx-generic-zte_mf18a-squashfs-sysupgrade.bin

previously wgeting bin. Sometimes it could print ubi attach error, but please ignore it if process goes forward.

Back to Stock (!!! need original dump taken from initramfs !!!) -------------

Place mtd8.bin and mtd9.bin initramfs image for the device on a TFTP in the server's root. This example uses Server IP: 192.168.0.2
Connect serial console (115200,8n1) to serial console connector .
Connect TFTP server to RJ-45 port (WAN/LAN1).
rename mtd8.bin to web.img and mtd9.bin to root_uImage_s
Stop in u-Boot (using ESC button) and run u-Boot commands:
This will erase Web and RootFS:
nand erase 0x1000000 0x800000
nand erase 0x1800000 0x1D00000

This will restore RootFS:
tftpboot 0x84000000 root_uImage_s
nand erase 0x1800000 0x1D00000
nand write 0x84000000 0x1800000 0x1D00000

This will restore Web Interface:
tftpboot 0x84000000 web.img
nand erase 0x1000000 0x800000
nand write 0x84000000 0x1000000 0x800000

After first boot on stock firwmare, do a factory reset. Push reset button for 5 seconds so all parameters will be reverted to the one printed on label on bottom of the router

As reference was taken MF289F support by Giammarco Marzano stich86@gmail.com and MF286D by Pawel Dembicki paweldembicki@gmail.com

Signed-off-by: Marcin Gajda <mgajda@o2.pl>
2023-01-14 19:19:36 +01:00
Mikhail Zhilkin
1a35edfbdb ramips: add basic support for TP-Link EC330-G5u v1
This adds basic support for TP-Link EC330-G5u Ver:1.0 router (also known
as TP-Link Archer C9ERT).

Device specification
--------------------
SoC Type: MediaTek MT7621AT
RAM: 128 MiB, Nanya NT5CC64M16GP-DI
Flash: 128 MiB NAND, ESMT F59L1G81MA-25T
Wireless 2.4 GHz (MediaTek MT7615N): b/g/n, 4x4
Wireless 5 GHz (MediaTek MT7615N): a/n/ac, 4x4
Ethernet: 5xGbE (WAN, LAN1, LAN2, LAN3, LAN4)
USB ports: 1xUSB3.0
Button: 4 (Led, WiFi On/Off, Reset, WPS)
LEDs: 7 blue LEDs, 1 orange(amber) LED, 1 white(non-gpio) LED
Power: 12 VDC, 2 A
Connector type: Barrel
Bootloader: First U-Boot (1.1.3), Main U-Boot (1.1.3). Additionally,
original TP-Link firmware contains Image U-Boot (1.1.3).

Serial console (UART)
---------------------
                            V
+-------+-------+-------+-------+
| +3.3V |  GND  |  TX   |  RX   |
+---+---+-------+-------+-------+
    |              J2
    |
    +--- Don't connect

Installation
------------
1. Rename OpenWrt initramfs image to test.bin and place it on tftp server
   with IP 192.168.0.5
2. Attach UART, switch on the router and interrupt the boot process by
   pressing 't'
3. Load and run OpenWrt initramfs image:
      tftpboot
      bootm
4. Once inside OpenWrt, switch to the first boot image:
      fw_setenv BootImage 0
5. Run 'sysupgrade -n' with the sysupgrade OpenWrt image

Back to Stock
-------------
1. Run in the OpenWrt shell:
      fw_setenv BootImage 1
      reboot

Recovery
--------
1. Press Reset button and power on the router
2. Navigate to U-Boot recovery web server (http://192.168.0.1/) and upload
   the OEM firmware

MAC addresses
-------------
+---------+-------------------+-------------------+-------------+
|         | MAC example 1     | MAC example 2     | Algorithm   |
+---------+-------------------+-------------------+-------------+
| label   | 68:ff:7b:xx:xx:f4 | 50:d4:f7:xx:xx:da | label       |
| LAN     | 68:ff:7b:xx:xx:f4 | 50:d4:f7:xx:xx:da | label       |
| WAN     | 72:ff:7b:xx:xx:f5 | 54:d4:f7:xx:xx:db | label+1 [1] |
| WLAN 2g | 68:ff:7b:xx:xx:f4 | 50:d4:f7:xx:xx:da | label       |
| WLAN 5g | 68:ff:7b:xx:xx:f6 | 50:d4:f7:xx:xx:dc | label+2     |
+---------+-------------------+-------------------+-------------+
label MAC address was found in factory at 0x165 (text format
xx:xx:xx:xx:xx:xx).

Notes
-----
[1] WAN MAC address:
   a. First octet of WAN MAC is differ than others and OUI is not related
      to TP-Link company. This probably should be fixed.
   b. Flipping bits in first octet and hex delta are different for the
      different MAC examples:
      +-----------------+----------------+----------------+
      |                 | Example 1      | Example 2      |
      +-----------------+----------------+----------------+
      | LAN             | 68 = 0110 1000 | 50 = 0101 0000 |
      | MAC (1st octet) |         ^ ^ ^  |                |
      +-----------------+----------------+----------------+
      | WAN             | 72 = 0111 0010 | 54 = 0101 0100 |
      | MAC (1st octet) |         ^ ^ ^  |            ^   |
      +-----------------+----------------+----------------+
      | HEX delta       | 0xa            | 0x4            |
      +-----------------+----------------+----------------+
      | DEC delta       | 4              | 4              |
      +-----------------+----------------+----------------+
   c. DEC delta is a constant (4). This looks like a mistake in OEM
      firmware and probably should be fixed.
   Based on the above, I decided to keep correct OUI and make WAN MAC =
   label + 1.

[2] Bootloaders
   The device contains 3 bootloaders:
   - First U-Boot: U-Boot 1.1.3 (Mar 18 2019 - 12:50:24). The First U-Boot
     located on NAND Flash to load next full-feature Uboot.
   - Main U-Boot + its backup: U-Boot 1.1.3 (Mar 18 2019 - 12:50:29). This
     bootloader includes recovery webserver. Requires special uImages to
     continue the boot process:
        0x00 (os0, os1) - firmware uImage
        0x40 (os0, os1) - standalone uImage (OpenWrt kernel is here)
   - Additionally, both slots of the original TP-Link firmware contains
     Image U-Boot: U-Boot 1.1.3 (Oct 16 2019 - 08:14:45). It checks image
     magics and CRCs. We don't use this U-Boot with OpenWrt.

Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
2023-01-14 18:36:33 +01:00
Nick Hainke
c051693ef4 trace-cmd: update to v3.1.6
Update to latest release.

Signed-off-by: Nick Hainke <vincent@systemli.org>
2023-01-13 22:02:20 +01:00
Nick Hainke
d649c32989 libtracefs: update to 1.6.4
Update to latest release.

Signed-off-by: Nick Hainke <vincent@systemli.org>
2023-01-13 22:02:20 +01:00
Nick Hainke
d1bdf5a9d9 libtraceevent: update to 1.7.1
Update to latest release.

Signed-off-by: Nick Hainke <vincent@systemli.org>
2023-01-13 22:02:20 +01:00
Daniel Golle
3d5c5427e1 uboot-mediatek: update to U-Boot 2023.01
Support for MT7981 and MT7986 has been merged, remove patches.
Tested on a couple of MT7986, MT7622 and MT7623 boards.
MIPS builds are untested.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-01-13 14:49:52 +00:00
Linhui Liu
5b605f4b51 uboot-envtools: update to 2023.01
Update to latest version.

Signed-off-by: Linhui Liu <liulinhui36@gmail.com>
2023-01-13 14:49:52 +00:00
Robert Marko
c83dbcdf8f
mac80211: ath11k: fix monitor bringup
Currently, ath11k will crash the crash if we try to bringup the monitor
mode interface.
Luckily, it has already been fixed upstream, so backport the patches
fixing it.

Fixes: 93ae4353cd ("mac80211: add ath11k PCI support")
Signed-off-by: Robert Marko <robimarko@gmail.com>
2023-01-12 15:17:18 +01:00
Christian Marangi
d9aa41dcda
lldpd: use release tar instead of codeload
There is currently a problem with making reproducible version of lldpd.
The tool version is generated based on 3 source:
1. .dist-version file in release tar
2. git hash with presence of .git directory
3. current date

Using the codeload tar from github results in getting the repo without
the .git directory and since they are not release tar, we don't have
.dist-version. This results in having lldpd bin with a version set to
the current build time.

Switch to release tar so that we correctly have a .dist-version file and
the version is not based on the build time.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Robert Marko <robimarko@gmail.com>
2023-01-12 14:55:07 +01:00
Hauke Mehrtens
76c67fcc66 ksmbd: Fix ZDI-CAN-18259
This fixes a security problem in ksmbd. It currently has the
ZDI-CAN-18259 ID assigned, but no CVE yet.

Backported from:
8824b7af40
cc4f3b5a6a

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2023-01-11 22:07:51 +01:00
Christian Marangi
ee397759b6
iwinfo: update to latest Git HEAD
c7b420a devices: add Qualcomm Atheros QCN6024/9024/9074 cards
5914d71 iwinfo: devices: add Qualcomm Atheros IPQ8074 WiSoC

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2023-01-10 00:54:31 +01:00
Felix Fietkau
0cc1c302b1 ucode-mod-bpf: add new package for a ucode libbpf binding
The bpf plugin provides functionality for loading and interacting with
eBPF modules.

It allows loading full modules and pinned maps/programs and supports
interacting with maps and attaching programs as tc classifiers.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2023-01-09 11:35:20 +01:00
Felix Fietkau
d6a284e4ce ucode: update to the latest version
34cfbb922c96 README.md: various spelling and documentation fixes
ff32355ea645 build: make rtnl/nl80211 depend on linux instead of !APPLE
c0e413c21f7b include: add uc_fn_thisval()
1e4d20932646 Merge pull request #134 from nbd168/thisval

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2023-01-09 11:35:20 +01:00
Hauke Mehrtens
25223b22c8 rtl8812au-ct: Ignore address errors
GCC 12.2.0 shows these error messages:
````
rtl8812au-ct-2021-11-07-39df5596/core/rtw_sta_mgt.c: In function 'rtw_mfree_stainfo':
rtl8812au-ct-2021-11-07-39df5596/core/rtw_sta_mgt.c:210:24: error: the comparison will always evaluate as 'true' for the address of 'lock' will never be NULL [-Werror=address]
  210 |         if(&psta->lock != NULL)
      |                        ^~
In file included from rtl8812au-ct-2021-11-07-39df5596/include/drv_types.h:109,
                 from rtl8812au-ct-2021-11-07-39df5596/core/rtw_sta_mgt.c:22:
rtl8812au-ct-2021-11-07-39df5596/include/sta_info.h:95:17: note: 'lock' declared here
   95 |         _lock   lock;
      |                 ^~~~
````

````
  CC [M]  rtl8812au-ct-2021-11-07-39df5596/os_dep/linux/ioctl_cfg80211.o
rtl8812au-ct-2021-11-07-39df5596/os_dep/linux/ioctl_cfg80211.c: In function 'cfg80211_rtw_scan':
rtl8812au-ct-2021-11-07-39df5596/os_dep/linux/ioctl_cfg80211.c:2176:32: warning: the comparison will always evaluate as 'true' for the address of 'ssid' will never be NULL [-Waddress]
 2176 |                 if(ssids->ssid != NULL
      |                                ^~
In file included from rtl8812au-ct-2021-11-07-39df5596/include/osdep_service_linux.h:88,
                 from rtl8812au-ct-2021-11-07-39df5596/include/osdep_service.h:41,
                 from rtl8812au-ct-2021-11-07-39df5596/include/drv_types.h:32,
                 from rtl8812au-ct-2021-11-07-39df5596/os_dep/linux/ioctl_cfg80211.c:22:
/home/hauke/openwrt/openwrt/staging_dir/target-mips_24kc_musl/usr/include/mac80211/net/cfg80211.h:2364:12: note: 'ssid' declared here
 2364 |         u8 ssid[IEEE80211_MAX_SSID_LEN];
      |            ^~~~
````

````
  CC [M]  rtl8812au-ct-2021-11-07-39df5596/hal/OUTSRC/phydm_debug.o
rtl8812au-ct-2021-11-07-39df5596/hal/OUTSRC/phydm_debug.c: In function 'phydm_cmd_parser':
rtl8812au-ct-2021-11-07-39df5596/hal/OUTSRC/phydm_debug.c:873:28: warning: the comparison will always evaluate as 'true' for the pointer operand in 'input + ((sizetype)i + 1) * 16' must not be NULL [-Waddress]
  873 |                         if(input[i+1]) {
      |                            ^~~~~
rtl8812au-ct-2021-11-07-39df5596/hal/OUTSRC/phydm_debug.c:894:28: warning: the comparison will always evaluate as 'true' for the pointer operand in 'input + ((sizetype)i + 1) * 16' must not be NULL [-Waddress]
  894 |                         if(input[i+1]) {
      |                            ^~~~~
````

This one was only seen on the rockchip/armv8 target:
````
  CC [M]  rtl8812au-ct-2021-11-07-39df5596/core/rtw_br_ext.o
In function '__nat25_add_pppoe_tag',
    inlined from 'nat25_db_handle' at rtl8812au-ct-2021-11-07-39df5596/core/rtw_br_ext.c:909:10:
rtl8812au-ct-2021-11-07-39df5596/core/rtw_br_ext.c:118:9: error: 'memcpy' reading between 2052 and 9220 bytes from a region of size 40 [-Werror=stringop-overread]
  118 |         memcpy((unsigned char *)ph->tag, tag, data_len);
      |         ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
rtl8812au-ct-2021-11-07-39df5596/core/rtw_br_ext.c: In function 'nat25_db_handle':
rtl8812au-ct-2021-11-07-39df5596/core/rtw_br_ext.c:878:63: note: source object 'tag_buf' of size 40
  878 |                                                 unsigned char tag_buf[40];
      |                                                               ^~~~~~~
````

Most of them are looking like real errors to me, but some fixes need a
deeper understanding of the driver and probably bigger changes to the driver.

Ignore these error messages for now. It would be nice if someone would
fix them.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2023-01-09 00:23:22 +01:00
Hauke Mehrtens
dc12c76dc5 uqmi: Ignore wrong maybe-uninitialized and dangling-pointer error
GCC 12.2.0 shows this false positive error message:
````
uqmi-2022-05-04-56cb2d40/dev.c: In function 'qmi_request_wait':
uqmi-2022-05-04-56cb2d40/dev.c:217:23: error: storing the address of local variable 'complete' in '*req.complete' [-Werror=dangling-pointer=]
  217 |         req->complete = &complete;
      |         ~~~~~~~~~~~~~~^~~~~~~~~~~
uqmi-2022-05-04-56cb2d40/dev.c:208:14: note: 'complete' declared here
  208 |         bool complete = false;
      |              ^~~~~~~~
uqmi-2022-05-04-56cb2d40/dev.c:208:14: note: 'req' declared here
cc1: all warnings being treated as errors
````

and this one:
````
In file included from uqmi-2022-05-04-56cb2d40/commands.c:28:
In function 'blobmsg_close_table',
    inlined from 'cmd_nas_get_cell_location_info_cb' at /home/haukeuqmi-2022-05-04-56cb2d40/commands-nas.c:897:4:
/usr/include/libubox/blobmsg.h:256:9: error: 'c' may be used uninitialized [-Werror=maybe-uninitialized]
  256 |         blob_nest_end(buf, cookie);
      |         ^~~~~~~~~~~~~~~~~~~~~~~~~~
In file included from uqmi-2022-05-04-56cb2d40/commands.c:169:
uqmi-2022-05-04-56cb2d40/commands-nas.c: In function 'cmd_nas_get_cell_location_info_cb':
uqmi-2022-05-04-56cb2d40/commands-nas.c:713:15: note: 'c' was declared here
  713 |         void *c, *t, *cell, *freq;
      |               ^
cc1: all warnings being treated as errors
````

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2023-01-09 00:10:52 +01:00
Hauke Mehrtens
2748c45d46 elfutils: Ignore wrong use-after-free error
GCC 12.2.0 shows this false positive error message:
````
In function 'bigger_buffer',
    inlined from '__libdw_gunzip' at gzip.c:374:12:
gzip.c:96:9: error: pointer may be used after 'realloc' [-Werror=use-after-free]
   96 |     b = realloc (state->buffer, more -= 1024);
      |         ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
gzip.c:94:13: note: call to 'realloc' here
   94 |   char *b = realloc (state->buffer, more);
      |             ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
````

GCC bug report: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=104069

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2023-01-09 00:10:52 +01:00
Hannu Nyman
98b09ba250 busybox: update to 1.36.0
Update busybox to version 1.36.0

* refresh patches (remove the backported upstream fix)
* refresh config

Config refresh:

Refresh commands, run after busybox is first built once:

cd package/utils/busybox/config/
../convert_menuconfig.pl ../../../../build_dir/target-arm_cortex-a15+neon-vfpv4_musl_eabi/busybox-default/busybox-1.36.0
cd ..
./convert_defaults.pl ../../../build_dir/target-arm_cortex-a15+neon-vfpv4_musl_eabi/busybox-default/busybox-1.36.0/.config > Config-defaults.in

Manual edits needed after config refresh:

* Config-defaults.in: OpenWrt config symbol IPV6 logic applied to
  BUSYBOX_DEFAULT_FEATURE_IPV6

* Config-defaults.in: OpenWrt config TARGET_bcm53xx logic applied to
  BUSYBOX_DEFAULT_TRUNCATE (commit 547f1ec)

* Config-defaults.in: OpenWrt logic applied to
  BUSYBOX_DEFAULT_LOGIN_SESSION_AS_CHILD (commit dc92917)

* Config-defaults.in: correct the default ports that get reset
  BUSYBOX_DEFAULT_FEATURE_HTTPD_PORT_DEFAULT    80
  BUSYBOX_DEFAULT_FEATURE_TELNETD_PORT_DEFAULT  23

* config/editors/Config.in: Add USE_GLIBC dependency to
  BUSYBOX_CONFIG_FEATURE_VI_REGEX_SEARCH (commit f141090)

* config/shell/Config.in: change at "Options common to all shells" the conditional symbol
  SHELL_ASH --> BUSYBOX_CONFIG_SHELL_ASH
  (discussion in http://lists.openwrt.org/pipermail/openwrt-devel/2021-January/033140.html
  Apparently our script does not see the hidden option while
  prepending config options with "BUSYBOX_CONFIG_" which leads to a
  missed dependency when the options are later evaluated.)

* Edit a few Config.in files by adding quotes to sourced items in
  config/Config.in, config/networking/Config.in and config/util-linux/Config.in (commit 1da014f)

Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
2023-01-07 17:22:54 +01:00
Linhui Liu
9ee12db67c util-linux: update to 2.38.1
Release Notes:
    https://cdn.kernel.org/pub/linux/utils/util-linux/v2.38/v2.38.1-ReleaseNotes

Remove upstreamed:
- 010-meson-typo.patch
- 020-meson-fix-compilation-without-systemd.patch
- 110-meson-fix-when-HAVE_CLOCK_GETTIME-is-set.patch

Signed-off-by: Linhui Liu <liulinhui36@gmail.com>
2023-01-07 17:18:41 +01:00
Shiji Yang
9a07895729 mt76: add stand-alone MT7622 firmware package
Add a separate firmware package to avoid installing the MT7615 firmware
on all MT7622 target devices by default. Now we only add MT7615 firmware
packages for devices that use MT7615E. This commit also removes the
explicit dependency on kmod-mt7615e to refine the package dependency.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2023-01-07 17:11:00 +01:00
Shiji Yang
fc9dd3f083 mt76: add stand-alone MT7915 firmware package
The mt7915e driver supports MT7915, MT7916 and MT7986 chips. And Only
MT7915 series chips need the MT7915 firmware. To save storage, extract
them from the common code package and create a new package to provide
the firmware.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2023-01-07 17:11:00 +01:00
Shiji Yang
3410f010a2 mt76: remove unnecessary dependency from mt7915e
The kmod-mt7615-common package does not contain any code that
related to mt7915e Wi-Fi6 driver, so remove it.

Tested on ramips/mt7621: SIM SIMAX1800T

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2023-01-07 17:11:00 +01:00
David Bauer
f97ce066a8 zyxel-bootconfig: clean up script
Drop unused variable and fix identation.

Signed-off-by: David Bauer <mail@david-bauer.net>
2023-01-07 01:32:58 +01:00
Nick Hainke
5809fb4546 tcpdump: update to 4.99.2
Update to latest version. For release information look into CHANGES
file [0].

Automatically refreshed:
- 001-remove_pcap_debug.patch

Manually refreshed:
- 100-tcpdump_mini.patch

old ipkg sizes:
316554 bin/packages/mips_24kc/base/tcpdump_4.99.1-1_mips_24kc.ipk
141457 bin/packages/mips_24kc/base/tcpdump-mini_4.99.1-1_mips_24kc.ipk

new ipkg sizes:
318089 bin/packages/mips_24kc/base/tcpdump_4.99.2-1_mips_24kc.ipk
141941 bin/packages/mips_24kc/base/tcpdump-mini_4.99.2-1_mips_24kc.ipk

[0] - https://github.com/the-tcpdump-group/tcpdump/blob/master/CHANGES

Signed-off-by: Nick Hainke <vincent@systemli.org>
2023-01-06 16:22:28 +01:00
Nick Hainke
acbae4f234 libpcap: update to 1.20.2
A huge rewrite in libpcap was introduced by dc14a7babca1 ("rpcap: have
the server tell the client its byte order.") [0]. The patch
"201-space_optimization.patch" does not apply at all anymore. So remove
it.

Refresh:
- 100-no-openssl.patch
- 102-skip-manpages.patch

Update the "300-Add-support-for-B.A.T.M.A.N.-Advanced.patch" with latest
PR [1].

old ipkg size:
90964 bin/packages/mips_24kc/base/libpcap1_1.10.1-5_mips_24kc.ipk

new ipkg size:
93340 bin/packages/mips_24kc/base/libpcap1_1.10.2-1_mips_24kc.ipk

[0] - dc14a7babc
[1] - https://github.com/the-tcpdump-group/libpcap/pull/980

Signed-off-by: Nick Hainke <vincent@systemli.org>
2023-01-06 16:20:06 +01:00
Nick Hainke
b331ffe807 nftables: update to 1.0.6
Remove upstreamed patches:
- 0001-fix-nft.patch

Upstream switched to "tar.xz" archives.

old ipkg size:
273678 bin/packages/mips_24kc/base/nftables-json_1.0.5-2_mips_24kc.ipk

new ipkg size:
271624 bin/packages/mips_24kc/base/nftables-json_1.0.6-1_mips_24kc.ipk

Release Information:
https://netfilter.org/projects/nftables/files/changes-nftables-1.0.6.txt

Signed-off-by: Nick Hainke <vincent@systemli.org>
2023-01-06 16:14:45 +01:00
Michael Pratt
1e3a8f454e base-files: rework mtd_get_mac_text()
It's necessary to be able to specify the length
for MAC addresses that are stored in flash, for example,
in a case where it is stored without any delimiter.

Let both offset and length have default values.

Add a sanity check related to partition size.

Also, clean up syntax and unnecessary lines.

Signed-off-by: Michael Pratt <mcpratt@pm.me>
2023-01-06 15:34:07 +01:00
Linhui Liu
87b9825521 ncurses: update to 6.4
Update to the latest released version.

Signed-off-by: Linhui Liu <liulinhui36@gmail.com>
2023-01-05 00:11:53 +01:00
Nikolay Martynov
665c2154ef ramips: add basic support for tp-link er605-v2
This is a MT7621-based device with 128MB NAND flash, 256MB RAM, and a USB port.
The board has headers to attach console. In order for them to work two solder
bridges near those pads need to be made.

The defice has the following partition table:

```
0x000000000000-0x000000080000 : "u-boot"
0x000000080000-0x000000100000 : "u-boot-env"
0x000000100000-0x000000140000 : "factory"
0x000000140000-0x000007e00000 : "firmware"
0x000007e00000-0x000008000000 : "panic-ops"
```

`firmware` partition contains UBI volumes. Unfortunately I accidentally wiped
partition and I no longer have access to it.

`firmware` partition contains 'secondary' U-Boot which is run by 'first' u-boot.
It also contains various configuration partitions that include device info and
MAC address. There also seems to be 'primary' and 'backup' set of 'main' volumes.

U-boot has `mtkupgrade` command that just overrides data on firmware partitions.
Firmware file provided by TP-Link cannot be used with that command.

U-boot also has 'recovery' http server. Unfortunately I was not able to make it
work with manufacturer's firmware.

Manufacturer's firmware essentially contains multiple UBI volumes along with
'partition table'. Unfortunately I no longer can properly run manufacturer's
firmware so I cannot at the moment try to a support for building 'factory' images.

This patch adds support for initramfs image as well as sysupgrade image.

This seems to be pretty standard MT7621 board otherwise.

Things that work:
* network
* leds
* usb
* factory MAC detection

Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
2023-01-04 23:19:19 +01:00
Felix Fietkau
4455ed65c6 bridger: update to the latest version
def7755c459d add missing copyright headers
f68307fd96d7 add hairpin mode support
9ee8f433ba4e nl: do not pass NDA_VLAN with vid=0
978c1f9eed07 add support for the bridge port isolated flag

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2023-01-03 13:28:47 +01:00
Hauke Mehrtens
ee47a28cec treewide: Trigger reinstall of all wolfssl dependencies
The ABI of the wolfssl library changed a bit between version 5.5.3 and
5.5.4. This release update will trigger a rebuild of all packages which
are using wolfssl to make sure they are adapted to the new ABI.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2023-01-01 21:06:54 +01:00
Nick Hainke
04634b2d82 wolfssl: update to 5.5.4-stable
Remove upstreamed:
- 001-Fix-enable-devcrypto-build-error.patch

Refresh patch:
- 100-disable-hardening-check.patch

Release notes:
https://github.com/wolfSSL/wolfssl/releases/tag/v5.5.4-stable

Signed-off-by: Nick Hainke <vincent@systemli.org>
2023-01-01 21:05:31 +01:00
Hauke Mehrtens
55d176fd0b tfa-layerscape: Use trusted-firmware-a.mk
This converts the trusted firmware arm build Makefile to make use of
the common trusted-firmware-a.mk file. This also fixes the build with
binutils 2.39.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2022-12-31 20:02:09 +01:00
Hauke Mehrtens
c5bb7a99a6 arm-trusted-firmware-mvebu: Use host flags for cryptest compilation
Without these changes it used the system LDFLAGS for the compilation of
the cryptopp library. This does not always work when we add
"-no-warn-rwx-segments" which is done to support binutils 2.39 inside of
OpenWrt.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2022-12-31 19:55:42 +01:00
Hauke Mehrtens
dd9d1a8ccb arm-trusted-firmware-sunxi: Use common trusted-firmware-a.mk
Make use of the definitions from trusted-firmware-a.mk to build the
Trusted firmware arm. This fixes the build with binutils 2.39.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2022-12-31 19:03:00 +01:00
Tony Ambardar
9cbc825b30 base-files: stage2: add 'tail' to sysupgrade environment
This is used to access footer data in firmare files, and is simpler and
less error-prone than using 'dd' with calculated offsets.

Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
2022-12-31 05:02:38 -08:00
Tony Ambardar
2a9f3b7717 ipq40xx: fix up Linksys WHW01 board name, device definition
Update the board name defined in DTS to match online documentation and the
name encoded into factory firmware. This helps supports flashing firmware
factory images using 'sysupgrade'.

Original WHW01 device definition assumes the rootfs IMAGE_SIZE is 33 MB
instead of the correct 74 MB, and defines factory images which include
extra adjustments/padding that do not match OEM factory images and may
cause problems flashing. Update image size and build recipe to fix these.

Suggested-by: Wyatt Martin <wawowl@gmail.com>
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
2022-12-31 05:02:38 -08:00
Hauke Mehrtens
af3c9b74e1 mbedtls: update to version 2.28.2
Changelog: https://github.com/Mbed-TLS/mbedtls/releases/tag/v2.28.2
This release of Mbed TLS provides bug fixes and minor enhancements. This
release includes fixes for security issues.

Fixes the following CVEs:
* CVE-2022-46393: Fix potential heap buffer overread and overwrite in
DTLS if MBEDTLS_SSL_DTLS_CONNECTION_ID is enabled and
MBEDTLS_SSL_CID_IN_LEN_MAX > 2 * MBEDTLS_SSL_CID_OUT_LEN_MAX.

* CVE-2022-46392: An adversary with access to precise enough information
about memory accesses (typically, an untrusted operating system
attacking a secure enclave) could recover an RSA private key after
observing the victim performing a single private-key operation if the
window size used for the exponentiation was 3 or smaller.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2022-12-31 03:19:58 +01:00
Felix Fietkau
12fdb4c9f4 mac80211: fix receiving multicast packets on multiple sta interfaces
Also fix MLO sta sdata link initialization

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-12-30 21:20:04 +01:00
Felix Fietkau
2e61469a6c netifd: update to the latest version
2cffe0c44e62 treewide: correctly apply IFNAMSIZ limit
96bcbb2e4eb6 wireless: allow set_retry ubus notify command to trigger a wdev restart
a2e8cd75dbf6 wireless: add support for disabling multicast-to-unicast per virtual interface
e9f44189ade7 system: move netdev types to system-linux.c where they are used
a3fab0119ef1 utils: include utils.h last
7ce73fc16765 vlandev: propagate topology changes
81c1fbcba2f2 device: fix vlan device issues with disappearing lower devices

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-12-30 16:42:57 +01:00
Chuanhong Guo
d29dbf052a
mediatek: drop redmi-ax6000 variant with modified env
This variant uses xiaomi factory u-boot and modified u-boot-env &
bootcmd.
By modifying uboot-env, the xiaomi firmware recovery provided in
the vendor u-boot doesn't work anymore. It's possible to put
u-boot into a state where it refuese to take any serial input.
If the u-boot is in this state, users can't restore their
firmware without taking the flash off the board.
We now have a -stock variant where the vendor u-boot is used in
a way that xiaomi firmware recovery still works, and a -ubootmod
variant where we get rid of all xiaomi components, have more
usable space and no uart console lock. These two should cover all
use cases and we don't need this variant anymore.
Drop this redmi-ax6000 variant. Existing users of this variant
should perform a u-boot mod or restore to the -stock layout.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2022-12-30 16:11:59 +08:00
Hauke Mehrtens
f12bad6c19 tree-wide: Do not use package librt and libpthread
The libraries libpthread, libdl, libutil, libanl have been integrated
into the libc library in version 2.34. it is not needed to explicitly
link them any more.

Most of the functions have been moved from the librt.so into libc.so
some time ago already.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2022-12-29 18:50:24 +01:00
Robert Marko
9d8eff6799
linux-firmware: disable stripping
It has been brought to my attention that recently added WCN6855 firmware
is broken as it is getting stripped during building due to being 2 ELF
binaries.
I am sure WCN6750 and any other ELF binaries are having the same issue,
so since stripping firmware binaries is clearly unwanted disable it.

Fixes: b4d3694f81 ("linux-firmware: package ath11k consumer cards firmware")
Signed-off-by: Robert Marko <robimarko@gmail.com>
2022-12-29 14:15:55 +01:00
Furong Xu
1613e3340b uboot-mediatek: add support for Xiaomi Redmi Router AX6000
U-Boot flash instructions:

0. OpenWrt U-Boot does not support stock layout, it comes with recovery
boot support, automatic tftp recovery and never blocks UART.

A new flash layout is introduced, we call it OpenWrt U-Boot layout,
stock flash layout and the old OpenWrt layout are not supported.

During the whole flash procedure, please do not reboot or power off
unless requested explicitly, or you will break your device.

1. Your device should already running OpenWrt.
If not, follow the instructions to flash OpenWrt:
https://github.com/openwrt/openwrt/pull/11115

2. Backup BL2 Nvram Bdata Factory and FIP in case you break something or
in case you want to go back to stock firmware one day.

cat /dev/mtdblock0 > /tmp/BL2.bin
cat /dev/mtdblock1 > /tmp/Nvram.bin
cat /dev/mtdblock2 > /tmp/Bdata.bin
cat /dev/mtdblock3 > /tmp/Factory.bin
cat /dev/mtdblock4 > /tmp/FIP.bin

And save all whose bin files to somewhere safe.

Then backup your configurations, since ubiformat for entire mtd device is
required to create new ubootenv volume for OpenWrt U-Boot.

3. Run the following cmd to boot into an initramfs with the new OpenWrt
U-Boot layout that expand ubi partion to the end of flash:

ubiformat /dev/mtd7 -y -f /tmp/ax6000-ubootmod-initramfs-factory.ubi

4. After boot into initramfs, check mtd partion info.
The ubi partion should be mtd5

root@OpenWrt:~# cat /proc/mtd
dev:    size   erasesize  name
mtd0: 00100000 00020000 BL2
mtd1: 00040000 00020000 Nvram
mtd2: 00040000 00020000 Bdata
mtd3: 00200000 00020000 Factory
mtd4: 00200000 00020000 FIP
mtd5: 07a80000 00020000 ubi

5. Load kmod-mtd-rw to temporarily make the bootloader partions writable.
The kmod-mtd-rw is from the feeds, it is not packed in initramfs-factory
by default.

To install kmod-mtd-rw via opkg:

opkg update && opkg install kmod-mtd-rw

Or, download kmod-mtd-rw.ipk from OpenWrt server and install it manually
e.g:
https://downloads.openwrt.org/snapshots/targets/mediatek/filogic/kmods/
Select your OpenWrt release version and kernel version accordingly.

Load kmod-mtd-rw:
insmod /lib/modules/$(uname -r)/mtd-rw.ko i_want_a_brick=1

6. Run the following cmd to clean all pending crash dumps in pstore,
or OpenWrt U-Boot may boot into NAND recovery or tftp recovery.

rm -f /sys/fs/pstore/*

7. Format ubi and create new ubootenv volume:

ubidetach -p /dev/mtd5; ubiformat /dev/mtd5 -y; ubiattach -p /dev/mtd5
ubimkvol /dev/ubi0 -n 0 -N ubootenv -s 128KiB
ubimkvol /dev/ubi0 -n 1 -N ubootenv2 -s 128KiB

8. This is optional. Skip this if you do not want to have NAND recovery
boot feature offered by OpenWrt U-Boot. Don't worry, you always have
automatic tftp recovery feature enabled.

ubimkvol /dev/ubi0 -n 2 -N recovery -s 10MiB
ubiupdatevol /dev/ubi0_2 /tmp/ax6000-ubootmod-initramfs-recovery.itb

9. Now, flash new U-Boot. Bye-bye ugly stock U-Boot.

mtd write /tmp/ax6000-ubootmod-preloader.bin BL2
mtd write /tmp/ax6000-ubootmod-bl31-uboot.fip FIP

10. Flash the squashfs-sysupgrade.bin as usual:

sysupgrade -n /tmp/ax6000-ubootmod-squashfs-sysupgrade.itb

Enjoy!

Signed-off-by: Furong Xu <xfr@outlook.com>
2022-12-29 03:04:42 +00:00
Robert Marko
214c230a79 linux-firmware: ath11k: add symlink for WCN6855 hw2.1
WCN6855 exists in 2 HW revisions, but both use the same FW so upstream
just has a symlink for hw2.1 to hw2.0 that I forgot to make.

Fixes: b4d3694f81 ("linux-firmware: package ath11k consumer cards firmware")
Signed-off-by: Robert Marko <robimarko@gmail.com>
2022-12-28 21:57:05 +01:00
Nick Hainke
4f44b4e506 linux-firmware: update to 20221214
Changes:
f3c283e amdgpu: updated navi10 firmware for amd-5.4
ba115d4 amdgpu: updated yellow carp firmware for amd-5.4
b8aba70 amdgpu: updated raven2 firmware for amd-5.4
2b21c5e amdgpu: updated raven firmware for amd-5.4
fc9a1c9 amdgpu: updated PSP 13.0.8 firmware for amd-5.4
7d43336 amdgpu: updated GC 10.3.7 RLC firmware for amd-5.4
c089dab amdgpu: updated vega20 firmware for amd-5.4
75e3494 amdgpu: updated PSP 13.0.5 firmware for amd-5.4
31c5734 amdgpu: add VCN 4.0.0 firmware for amd-5.4
a735158 amdgpu: add SMU 13.0.0 firmware for amd-5.4
0bef6bb amdgpu: Add SDMA 6.0.0 firmware for amd-5.4
bb56d1a amdgpu: add PSP 13.0.0 firmware for amd-5.4
e32209f amdgpu: add GC 11.0.0 firmware for amd-5.4
613db81 amdgpu: add DCN 3.2.0 firmware for amd-5.4
1fc8f6c amdgpu: updated vega10 firmware for amd-5.4
2257447 amdgpu: updated beige goby firmware for amd-5.4
6aa0023 amdgpu: updated dimgrey cavefish firmware for amd-5.4
dd1225a amdgpu: updated vangogh firmware for amd-5.4
5cb010e amdgpu: updated picasso firmware for amd-5.4
edf9699 amdgpu: updated navy flounder firmware for amd-5.4
b7e83d9 amdgpu: updated green sardine firmware for amd-5.4
f820cc3 amdgpu: updated sienna cichlid firmware for amd-5.4
b77f539 amdgpu: updated arcture firmware for amd-5.4
dccfdf1 amdgpu: updated navi14 firmware for amd-5.4
5d1af6d amdgpu: updated renoir firmware for amd-5.4
13b9c94 amdgpu: updated navi12 firmware for amd-5.4
e9b8357 amdgpu: updated aldebaran firmware for amd-5.4
b4af754 sr150 : Add NXP SR150 UWB firmware
0707b2f brcm: add/update firmware files for brcmfmac driver
16c9630 rtl_bt: Update RTL8821C BT(USB I/F) FW to 0x75b8_f098
80ed874 amdgpu: update sdma_5.2.7 firmware
32d8681 QCA: Add Bluetooth firmware for WCN785x This commit will add required Bluetooth firmware files for QCA WCN785x. The image version is 2.0.0-00515.
cdf9499 linux-firmware: update firmware for MT7916
685ea4d linux-firmware: update firmware for MT7915
7f6279b i915: Add DMC v2.08 for DG2
391fb47 amdgpu: update green sardine DMCUB firmware
de854c9 i915: Add DMC v2.10 for MTL
daff404 linux-firmware: update firmware for MT7986
70494e3 linux-firmware: update firmware for mediatek bluetooth chip (MT7921)
750c0dc linux-firmware: update firmware for MT7921 WiFi device

Signed-off-by: Nick Hainke <vincent@systemli.org>
2022-12-28 20:20:01 +01:00
Felix Baumann
75451681d0
uboot-envtools: add support for ramips Asus RX-AX53U
Adds uboot-envtools support for ramips Asus RX-AX53U now that partition
can be correctly read.

Signed-off-by: Felix Baumann <felix.bau@gmx.de>
[ improve commit title and description ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-12-28 14:04:58 +01:00
Felix Fietkau
090ad03343 hostapd: allow sharing the incoming DAS port across multiple interfaces
Use the NAS identifier to find the right receiver context on incoming messages

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-12-27 19:10:04 +01:00
Hauke Mehrtens
fb15cb4ce9 iproute2: Fix build with GCC 12 and glibc 2.36
This fixes the detection of name_to_handle_at() when GCC 12 and glibc
2.36 are used.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2022-12-26 15:18:08 +01:00
Hauke Mehrtens
73dca49f35 uhttpd: update to latest Git HEAD
2397755 client: fix incorrectly emitting HTTP 413 for certain content lengths

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2022-12-26 15:18:08 +01:00
Xuefer H
ab31547df0 libbsd: fix libpath to not use host path
libpath.so uses host path in ld script causing other packages fail to
cross compile, e.g. perl:
"ld: cannot find /usr/lib/libbsd.so.0.11.6: No such file or directory"

Fixes: openwrt/packages#19390

Signed-off-by: Xuefer H <xuefer@gmail.com>
2022-12-26 13:36:41 +01:00
Kevin Darbyshire-Bryant
5c7e4a9d2e dnsmasq: bump to v2.88
Most relevant feature for openwrt in this release, supports dynamically
removing hosts from 'hostsdir' supplied host files.

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
2022-12-25 15:07:36 +00:00
Kuan-Yi Li
a5f16b4f4f
uboot-omap: build with omap generic subtarget
Fix image build fail by using the generic subtarget.

Fixes: b2bfea48 ("omap: add generic subtarget")
Ref: 40e3f660 ("uboot-fritz4040: build with ipq40xx generic subtarget")
Signed-off-by: Kuan-Yi Li <kyli@abysm.org>
[ add commit description ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-12-25 11:55:54 +01:00
Kuan-Yi Li
808046b2ee
uboot-tegra: build with tegra generic subtarget
Fix image build fail by using the generic subtarget.

Fixes: c028e1b1 ("tegra: add generic subtarget")
Ref: 40e3f660 ("uboot-fritz4040: build with ipq40xx generic subtarget")
Signed-off-by: Kuan-Yi Li <kyli@abysm.org>
[ add commit description ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-12-25 11:55:53 +01:00
Kuan-Yi Li
64bfb8b7d6
uboot-zynq: build with zynq generic subtarget
Fix image build fail by using the generic subtarget.

Fixes: 6d7129ef ("zynq: add generic subtarget")
Ref: 40e3f660 ("uboot-fritz4040: build with ipq40xx generic subtarget")
Signed-off-by: Kuan-Yi Li <kyli@abysm.org>
[ add commit description ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-12-25 11:55:53 +01:00
Kuan-Yi Li
1c35dc26f1
uboot-mxs: build with mxs generic subtarget
Fix image build fail by using the generic subtarget.

Fixes: 64ef920b ("mxs: add generic subtarget")
Ref: 40e3f660 ("uboot-fritz4040: build with ipq40xx generic subtarget")
Signed-off-by: Kuan-Yi Li <kyli@abysm.org>
[ add commit description ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-12-25 11:55:52 +01:00
Kuan-Yi Li
5c85c1f344
uboot-kirkwood: build with kirkwood generic subtarget
Fix image build fail by using the generic subtarget.

Fixes: cada395a ("kirkwood: add generic subtarget")
Ref: 40e3f660 ("uboot-fritz4040: build with ipq40xx generic subtarget")
Signed-off-by: Kuan-Yi Li <kyli@abysm.org>
[ add commit description ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-12-25 11:55:52 +01:00
Jan-Niklas Burfeind
c7d3bbb909 sunxi: ensure NanoPi R1 has unique MAC address
Ensure the MAC address for all NanoPi R1 boards is assigned uniquely for
each board.

The vendor ships the device in two variants; one with and one without
eMMC; but both without static mac-addresses.
In order to assign both board types unique MAC addresses, fall back on
the same method used for the NanoPi R2S and R4S in case the EEPROM
chip is not present by generating the board MAC from the SD card CID.

[0] https://wiki.friendlyelec.com/wiki/index.php/NanoPi_R1#Hardware_Spec

Similar too and based on:

commit b5675f500d ("rockchip: ensure NanoPi R4S has unique MAC address")

Co-authored-by: David Bauer <mail@david-bauer.net>
Signed-off-by: Jan-Niklas Burfeind <git@aiyionpri.me>
2022-12-25 02:27:55 +01:00
Hauke Mehrtens
cb7d662dac mac80211: Do not build brcmsmac on bcm47xx_legacy
brcmsmac needs bcma. bcma is build into the kernel for the other bcm47xx
subtargets, but not for the legacy target because it only uses ssb. We
could build bcma as a module for bcm47xx_legacy, but none of these old
devices uses a wifi card supported by brcsmac.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2022-12-24 15:14:58 +01:00
Felix Fietkau
274dfcb19e mt76: update to the latest version
a03ef0aab93e wifi: mt76: mt7921: fix deadlock in mt7921_abort_roc
5b509e80384a wifi: mt76: dma: fix a regression in adding rx buffers

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-12-22 16:19:55 +01:00
Jan-Niklas Burfeind
bf06a7c865 uboot-sunxi: use UUID of bootdev and bootpart
Several sunxi devices come with multiple mmc devices. On such devices,
the mmc device order is unpredictable, so using /dev/mmcblk0p2 as root
device doesn't always work, which results in unbootable devices.

For the Banana Pi BPI-R3 in the mediatek target, this has been solved by
defining aliases for the mmc devices in the DTS. Ideally we would do the
same here, but for sunxi-a64 we already use UUID probing, so let's start
with that (5f2ff607e2 ("uboot-sunxi: a64: allow booting directly from
eMMC")).

Since we're building and including u-boot in each supported device
image, and this method has been proven to work fine for a64, let's just
change the default u-boot env file to do the same.

Fixes: #10080
Fixes: e6d9f6fdff ("sunxi: add support for FriendlyARM NanoPi R1")
Co-authored-by: Karl Palsson <karlp@etactica.com>
Signed-off-by: Jan-Niklas Burfeind <git@aiyionpri.me>
[use UUID in default u-boot env, rewrite commit message]
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2022-12-22 13:33:47 +02:00
Jan-Niklas Burfeind
5b82eeb320 sunxi: remove frequency for NanoPi R1
The frequency appears as unlisted initial frequency.
Removed it as Hauke suggested.

Signed-off-by: Jan-Niklas Burfeind <git@aiyionpri.me>
2022-12-22 00:05:29 +01:00
Stijn Tintel
9ed1830bdc arm-trusted-firmware-sunxi: drop CPE ID
The CPE ID is already set in trusted-firmware-a.mk.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2022-12-20 18:36:26 +00:00
Daniel Golle
6675a9aaf4 xdp-tools: update to version 1.2.9
Changes since v1.2.8:
 32aaf32 libxdp: Fix incorrect rx_ring_setup_done
 6049671 headers: add bpf_endian.h for parsing_helpers.h
 2682c1c export-man: Ignore errors when executing git shell command
 8afda7a xdp-loader/README: Mention lack of support for HW mode in most cards
 dc69919 libxdp: fix prog_fd checks for fd >= 0
 3d7c22a libxdp: Allow falling back to single-program attachment for loaded programs
 af00429 libxdp: Fix check in xdp_program__attach_single()
 41703d2 libxdp: Make sure to set the the program autoload when loading a program
 b1fd2e5 test-xdpdump: Only run tshark attribute test on newer versions of tshark
 5dfe342 libxdp: Convert xdp-dispatcher to use strict section names
 929a22e configure: Try to auto-detect versioned clang binaries
 074fcfb libxdp: Check program name when determining if a program is a dispatcher
 e13a191 Bump TOOLS_VERSION to 1.2.9

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-12-20 13:57:34 +00:00
Rosen Penev
6d1df35747 hostapd: add mbedtls variant
This adds the current WIP mbedtls patches for hostapd. The motivation
here is to reduce size.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2022-12-19 12:27:35 +00:00
Robert Marko
93ae4353cd
mac80211: add ath11k PCI support
ath11k is the upstream driver for Qualcomm 802.11ax radios, both for the
internal AHB and PCI based cards.
This commit does however only provide PCI support while AHB will follow
but its SoC specific so it will require an OpenWrt target first.

It differs a bit from ath10k as it requires stuff like QRTR, MHI and QMI
helpers.

PCI variant requires qrtr-mhi and mhi-bus which backports do provide,
however we are dropping those in a patch as they will conflict with
support for the AHB variant as that one requires qrtr-smd which in turn
requires RPMSG and GLINK and its not feasable to provide those in
backports as they are really SoC specific.

QRTR and MHI in kernel 5.10 are not usable and backporting the changes
is not easy as they have changed drastically from 5.10 to 5.15 ath11k will
only be available on targets that use kernel 5.15.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2022-12-19 01:01:57 +01:00
Robert Marko
b4d3694f81
linux-firmware: package ath11k consumer cards firmware
Package firmware for ath11k supported QCA consumer cards from linux-firmware.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2022-12-19 01:01:57 +01:00
Robert Marko
5968290a21
kernel: package QRTR support
QRTR is Qualcomm IPC router protocol and ath11k requires it for both
AHB and PCI support, so package it as a kernel module so it can be
added as a dependency to the ath11k module.

Only kernel 5.15 is currently supported due to various things missing in
5.10 whose backporting is out of scope for this patch.

SMD, TUN and MHI variants are packaged.

SMD variant depends on the ipq807x
target as it has dependency on the RPMSG drivers which are Qualcomm
and SoC specific anyway.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2022-12-19 01:01:52 +01:00
Nick Hainke
8ed53e0928 iproute2: update to 6.1.0
Announcement:
https://lore.kernel.org/netdev/20221214094130.7b11ec2e@hermes.local/T/#t

Refresh patch:
- 170-ip_tiny.patch

Signed-off-by: Nick Hainke <vincent@systemli.org>
2022-12-18 16:33:16 +01:00
Alexey Bartenev
3f201d1f8e ramips: add support for SNR-CPE-W4N-MT router
General specification:
- SoC Type: MediaTek MT7620N (580MHz)
- ROM: 8 MB SPI-NOR (W25Q64FV)
- RAM: 64 MB DDR (M13S5121632A)
- Switch: MediaTek MT7530
- Ethernet: 5 ports - 5×100MbE (WAN, LAN1-4)
- Wireless 2.4 GHz: b/g/n
- Buttons: 1 button (RESET)
- Bootloader: U-Boot 1.1.3, MediaTek U-Boot: 5.0.0.5
- Power: 12 VDC, 1.0 A

Flash by the native uploader in 2 stages:
1. Use the native uploader to flash an initramfs image. Choose
 openwrt-ramips-mt7620-snr_cpe-w4n-mt-initramfs-kernel.bin file by
 "Administration/Management/Firmware update/Choose File" in vendor's
 web interface (ip: 192.168.1.10, login: Admin, password: Admin).
 Wait ~160 seconds.
2. Flash a sysupgrade image via the initramfs image. Choose
 openwrt-ramips-mt7620-snr_cpe-w4n-mt-squashfs-sysupgrade.bin
 file by "System/Backup/Flash Firmware/Flash image..." in
 LuCI web interface (ip: 192.168.1.1, login: root, no password).
 Wait ~240 seconds.

Flash by U-Boot TFTP method:
1. Configure your PC with IP 192.168.1.131
2. Set up TFTP server and put the
 openwrt-ramips-mt7620-snr_cpe-w4n-mt-squashfs-sysupgrade.bin
 image on your PC
3. Connect serial port (57600 8N1) and turn on the router.
 Then interrupt "U-Boot Boot Menu" by hitting 2 key (select "2:
 Load system code then write to Flash via TFTP.").
Press Y key when show "Warning!! Erase Linux in Flash then burn
 new one. Are you sure? (Y/N)"
Input device IP (192.168.1.1) ==:192.168.1.1
Input server IP (192.168.1.131) ==:192.168.1.131
Input Linux Kernel filename () ==:
openwrt-ramips-mt7620-snr_cpe-w4n-mt-squashfs-sysupgrade.bin
3. Wait ~120 seconds to complete flashing

Signed-off-by: Alexey Bartenev <41exey@proton.me>
2022-12-17 22:34:44 +01:00
Hauke Mehrtens
a442974cfa gdb: Do not link against xxhash
libxxhash is now available in the OpenWrt package feed and gdb will link
against it if gdb finds this library. Explicitly deactivate the usage
of xxhash.

This should fix the build of gdb in build bots.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2022-12-17 22:34:44 +01:00
Chukun Pan
53123b93b0 sunxi: fix board_name for MarsBoard A10
The compatible in the device tree is "haoyu,a10-marsboard",
modify the board_name to keep it consistent.

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
2022-12-17 20:55:47 +01:00
Nick Hainke
74b7d69601 strace: update to 6.1
Release Notes:
https://github.com/strace/strace/releases/tag/v6.1

Signed-off-by: Nick Hainke <vincent@systemli.org>
2022-12-17 20:28:18 +01:00
Nick Hainke
95ed519b25 trace-cmd: update to v3.1.5
Update to latest release.

Signed-off-by: Nick Hainke <vincent@systemli.org>
2022-12-17 20:24:46 +01:00
Nick Hainke
b5d317f47e libtracefs: update to 1.6.3
Update to latest release.

Signed-off-by: Nick Hainke <vincent@systemli.org>
2022-12-17 20:24:46 +01:00
Nick Hainke
b01f2d9f38 libtraceevent: update to 1.7.0
Update to latest release.

Signed-off-by: Nick Hainke <vincent@systemli.org>
2022-12-17 20:24:46 +01:00
Hauke Mehrtens
243a7256c1 kernel: Make use of KERNEL_MAKE
Make use of KERNEL_MAKE in kernel packages were easily possible.
This moves some more code to common places and reduces the number of
lines.

It is defined like this:
KERNEL_MAKE = $(MAKE) $(KERNEL_MAKEOPTS)
KERNEL_MAKEOPTS = -C $(LINUX_DIR) $(KERNEL_MAKE_FLAGS)

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2022-12-17 20:12:31 +01:00
Chen Minqiang
18bea173a6 mediatek: add alternative stock layout for Xiaomi Redmi Router AX6000
In this implementation, the flash partition layout is adjusted to avoid
modifying the uboot environment of mtdparts. This ensures that the 30M
ubi_kernel partition remains aligned with the stock ubi partition, and
the kernel volume is placed in it. This allows the stock uboot to boot
from it without changing the mtdparts, which is useful for reverting back
to the stock firmware using Xiaomi Firmware Tools. In actual testing,
modifying mtdparts has been found to break Xiaomi Firmware Tools.

1. use ARTIFACTS to generate initramfs-factory.ubi for easy installation.
2. The NAND flash layout is changed to allow for reverting back to the
   stock firmware.
3. Before performing sysupgrade, do some cleanup in platform_pre_upgrade
   to ensure a clean installation of OpenWRT.
4. Setup the uboot env to ensure that the system always boot, which can
   be helpful for users who may forget to do this before sysupgrade in
   the initramfs.

New flash instructions:
1. Gain ssh access. Please refer to:
   https://openwrt.org/toh/xiaomi/redmi_ax6000#installation)

2. Check which system current u-boot is loading from:
   COMMAND: `cat /proc/cmdline`
   sample OUTPUT: `console=ttyS0,115200n1 loglevel=8 firmware=1 uart_en=1`
   if firmware=1, current system is ubi1
   if firmware=0, current system is ubi0

3. Setup nvram and write the firmware:
   If the current system is ubi1, please set it up so that the next time
   it will boot from ubi, and write the firmware to ubi:
```
nvram set boot_wait=on
nvram set uart_en=1
nvram set flag_boot_rootfs=0
nvram set flag_last_success=0
nvram set flag_boot_success=1
nvram set flag_try_sys1_failed=0
nvram set flag_try_sys2_failed=0
nvram commit
ubiformat /dev/mtd8 -y -f /tmp/initramfs-factory.ubi
```
   If the current system is ubi, please set it up so that the next time
   it will boot from ubi1, and write the firmware to ubi1:
```
nvram set boot_wait=on
nvram set uart_en=1
nvram set flag_boot_rootfs=1
nvram set flag_last_success=1
nvram set flag_boot_success=1
nvram set flag_try_sys1_failed=0
nvram set flag_try_sys2_failed=0
nvram commit
ubiformat /dev/mtd9 -y -f /tmp/initramfs-factory.ubi
```

4. After rebooting, the system should now boot into the openwrt initramfs.
   Flash the squashfs-sysupgrade.bin via using ssh or luci.
```
sysupgrade -n /tmp/squashfs-sysupgrade.bin
```
Done.

For existing users of the Redmi AX6000 running OpenWrt, here are the steps to
switch to this new layout:

1. Flash initramfs-factory.ubi
```
mtd -r -e ubi write /tmp/initramfs-factory.ubi ubi
```

2. After rebooting, the system will boot into the new openwrt-initramfs.
Log in and perform a sysupgrade to complete the process.
```
sysupgrade -n /tmp/squashfs-sysupgrade.bin
```

Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2022-12-17 15:04:16 +08:00
Chuanhong Guo
189637c964 base-files: sysupgrade-tar: allow separated kernel/rootfs ubi
There are some devices putting kernel and rootfs on separated
ubi volumes. To make OpenWrt compatible with their bootloader,
we need to put kernel and rootfs into separated ubi volumes.
Add support for CI_KERN_UBIPART and CI_ROOT_UBIPART for this
situation.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2022-12-17 14:08:58 +08:00
Chuanhong Guo
c48e511fef base-files: split ubi attaching out of nand_upgrade_prepare_ubi
split ubi reformat/attach into nand_attach_ubi in preparation
for reusing this code in other functions.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2022-12-17 14:08:58 +08:00
Chuanhong Guo
9e2c01e4a6
kernel: add driver package for WS2812B LEDs
Two WS2812B (NeoPixel) clones are used in Xiaomi Redmi AX6000 as
indicator lights. Add a driver for controlling it using SPI MOSI.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2022-12-16 21:41:57 +08:00
Felix Fietkau
d07d47d0e3 mac80211: fix a regression in processing management frames for AP VLAN interfaces
Fixes re-assoc of WDS stations

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-12-16 14:32:47 +01:00
Felix Fietkau
581f2b15b2 hostapd: enable coredumps
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-12-16 14:32:47 +01:00
Felix Fietkau
c2fde432b3 hostapd: always set a default for the nas identifier
It is used for both 802.11r and WPA enterprise.
Setting it when not needed is harmless

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-12-16 14:32:47 +01:00
Felix Fietkau
133a1e2f37 mac80211: work around a race condition on detecting a phy while bringing it up
When reloading modules and running wifi, a phy can sometimes be renamed
while in the middle of a hotplug call that tries to detect new phys
This can lead to bogus wifi-device sections being created

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-12-16 14:32:47 +01:00
Felix Fietkau
92acd9f3e8 mac80211: fix uninitialized variable in rx->link/link_sta initialization fix
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-12-16 14:32:47 +01:00
Felix Fietkau
2fb38b77a2 hostapd: add support for automatically setting RADIUS own-ip dynamically
Some servers use the NAS-IP-Address attribute as a destination address

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-12-16 14:32:47 +01:00
Jo-Philipp Wich
d15b1fbed7 rpcd: update to latest Git HEAD
7de4820 iwinfo: add "hwmodes_text" to the info output
b3f530b iwinfo: clean up rpc_iwinfo_call_hw_ht_mode()
c46ad61 iwinfo: reuse infos provided by libiwinfo
6c5e900 iwinfo: constify string map arg for rpc_iwinfo_call_int()

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2022-12-16 00:55:51 +01:00
Jo-Philipp Wich
4a4d0bf78d iwinfo: update to latest Git HEAD
8d15809 cli: print current HT mode
8f86dd6 cli: use IWINFO_HTMODE_COUNT
f36b72b cli: use IWINFO_KMGMT_NAMES
91be7e0 cli: use IWINFO_CIPHER_NAMES
49b6ec9 cli: fix printing the scan channel width
b1c8873 cli: fix marking the active channel
9e14e64 utils: add iwinfo_band2ghz() and iwinfo_ghz2band() helpers
e084781 utils: add helper functions to get names by values
d09a77a utils: add iwinfo_htmode_is_{ht|vht|he} helpers
8752977 utils: add and use iwinfo_format_hwmodes()
02f433e lib: add IWINFO_80211_COUNT and IWINFO_80211_NAMES
1d30df1 lib: add IWINFO_BAND_COUNT and IWINFO_BAND_NAMES
aefd0ef lib: use common IWINFO_CIPHER_NAMES strings
a5b30de lib: add IWINFO_OPMODE_COUNT and use it for IWINFO_OPMODE_NAMES
9f29e79 lib: constify and fixup the string array definitions
fddc015 nl80211: mark frequencies where HE operation in not allowed
6d50a7c nl80211: add support for HE htmodes
4ba5713 nl80211: properly get available bands for the hwmode
91b2ada nl80211: update the kernel header nl80211.h
3f619a5 nl80211: fix frequency/channel conversion for the 6G band
a77d915 nl80211: don't guess if a name is an ifname
c27ce71 devices: add usb device MediaTek MT7921AU
14f864e nl80211: add ability to describe USB devices
a5a75fd nl80211: remove ancient wpa_supplicant ctrl socket path
dd4e1ff nl80211: fix wpa supplicant ctrl socket permissions
d638163 fix -Wdangling-else warnings
4aa6c5a fix -Wreturn-type warning
3112726 fix -Wpointer-sign warning
ebd5f84 fix -Wmaybe-uninitialized warning
5469898 fix -Wunused-variable warnings
462b679 fix -Wduplicate-decl-specifier warnings
ccaabb4 fix -Wformat-truncation warnings
50380db enable useful compiler warnings via -Wall

Fixes: https://github.com/openwrt/openwrt/issues/10158
Fixes: https://github.com/openwrt/openwrt/issues/10687
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2022-12-16 00:55:51 +01:00
Felix Fietkau
b7a7a97037 mac80211: fix connecting multiple wds stations to an AP
A faulty check prevented the AP_VLAN interfaces from being brought up

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-12-14 13:54:02 +01:00
Linus Lüssing
26d10bad7c libpcap: add support for B.A.T.M.A.N. Advanced
This adds support for the layer 2 mesh routing protocol
B.A.T.M.A.N. Advanced. "batadv" can be used to filter on batman-adv
packets. It also allows later filters to look at frames inside the
tunnel when both "version" and "type" are specified.

Documentation for the batman-adv protocol can be found at the following
locations:

https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/Documentation/networking/batman-adv.rst
https://www.open-mesh.org/

--

This is a backport of the following upstream pull request:

https://github.com/the-tcpdump-group/libpcap/pull/980
-> "Add support for B.A.T.M.A.N. Advanced #980"

Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
2022-12-14 01:06:26 +01:00
Mikhail Zhilkin
0ec8d991c2 ramips: add support for Etisalat S3
Etisalat S3 is a wireless WiFi 5 router manufactured by Sercomm company.

Device specification
--------------------
SoC Type: MediaTek MT7621AT
RAM: 256 MiB
Flash: 128 MiB
Wireless 2.4 GHz (MT7603EN): b/g/n, 2x2
Wireless 5 GHz (MT7615E): a/n/ac, 4x4
Ethernet: 5x GbE (WAN, LAN1, LAN2, LAN3, LAN4)
USB ports: 1x USB3.0
Button: 2 buttons (Reset & WPS)
LEDs:
   - 1x Status (RGB)
   - 1x 2.4G (blue, hardware, mt76-phy0)
   - 1x 5G (blue, hardware, mt76-phy1)
Power: 12 VDC, 1.5 A
Connector type: barrel
Bootloader: U-Boot

Installation
-----------------
1.  Login to the router web interface under admin account
2.  Navigate to Settings -> Configuration -> Save to Computer
3.  Decode the configuration. For example, using cfgtool.py tool (see
    related section):
       cfgtool.py -u configurationBackup.cfg
4.  Open configurationBackup.xml and find the following line:
    <PARAMETER name="Password" type="string" value="<your router serial \
       is here>" writable="1" encryption="1" password="1"/>
5.  Insert the following line after and save:
<PARAMETER name="Enable" type="boolean" value="1" writable="1" encryption="0"/>
6.  Encode the configuration. For example, using cfgtool.py tool:
       cfgtool.py -p configurationBackup.xml
7.  Upload the changed configuration (configurationBackup_changed.cfg) to
    the router
8.  Login to the router web interface (SuperUser:ETxxxxxxxxxx, where
    ETxxxxxxxxxx is the serial number from the backplate label)
9.  Navigate to Settings -> WAN -> Add static IP interface (e.g.
    10.0.0.1/255.255.255.0)
10. Navigate to Settings -> Remote cotrol -> Add SSH, port 22,
    10.0.0.0/255.255.255.0 and interface created before
11. Change IP of your client to 10.0.0.2/255.255.255.0 and connect the
    ethernet cable to the WAN port of the router
12. Connect to the router using SSH shell under SuperUser account
13. Run in SSH shell:
       sh
14. Make a mtd backup (optional, see related section)
15. Change bootflag to Sercomm1 and reboot:
       printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3
       reboot
16. Login to the router web interface under admin account
17. Remove dots from the OpenWrt factory image filename
18. Update firmware via web using OpenWrt factory image

Revert to stock
---------------
Change bootflag to Sercomm1 in OpenWrt CLI and then reboot:
   printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3

mtd backup
----------
1. Set up a tftp server (e.g. tftpd64 for windows)
2. Connect to a router using SSH shell and run the following commands:
      cd /tmp
      for i in 0 1 2 3 4 5 6 7 8 9 10; do nanddump -f mtd$i /dev/mtd$i; \
      tftp -l mtd$i -p 10.0.0.2; md5sum mtd$i >> mtd.md5; rm mtd$i; done
      tftp -l mtd.md5 -p 10.0.0.2

Recovery
--------
Use sercomm-recovery tool.
Link: https://github.com/danitool/sercomm-recovery

MAC Addresses
-------------
+-----+------------+---------+
| use | address    | example |
+-----+------------+---------+
| LAN | label      | *:50    |
| WAN | label + 11 | *:5b    |
| 2g  | label + 2  | *:52    |
| 5g  | label + 3  | *:53    |
+-----+------------+---------+
The label MAC address was found in Factory 0x21000

cfgtool.py
----------
A tool for decoding and encoding Sercomm configs.
Link: https://github.com/r3d5ky/sercomm_cfg_unpacker

Co-authored-by: Karim Dehouche <karimdplay@gmail.com>
Co-authored-by: Maximilian Weinmann <x1@disroot.org>
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
2022-12-13 23:06:20 +01:00
Felix Fietkau
a4339c5a21 mac80211: add a fix for a crash in __ieee80211_rx_h_amsdu
Fix initialization of rx->link_sta

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-12-13 21:14:43 +01:00
Andre Heider
7c63295bf4 treewide: remove DRIVER_11N_SUPPORT
hostapd's compile time option CONFIG_IEEE80211N was removed almost 3 years
ago, 80.211n/HT is always included since then.

Noticed because `hostapd -v11n` confusingly returned an error.

See hostapd's commit:
f3bcd69603 "Remove CONFIG_IEEE80211N build option"

Signed-off-by: Andre Heider <a.heider@gmail.com>
2022-12-13 10:54:50 +01:00
Andre Heider
2d36f60d88 hostapd: fix 350-nl80211_del_beacon_bss.patch
Pass the expected struct:

../src/drivers/driver_nl80211.c: In function 'wpa_driver_nl80211_del_beacon':
../src/drivers/driver_nl80211.c:2945:31: warning: passing argument 1 of 'nl80211_bss_msg' from incompatible pointer type [-Wincompatible-pointer-types]
 2945 |         msg = nl80211_bss_msg(drv, 0, NL80211_CMD_DEL_BEACON);
      |                               ^~~
      |                               |
      |                               struct wpa_driver_nl80211_data *
../src/drivers/driver_nl80211.c:695:50: note: expected 'struct i802_bss *' but argument is of type 'struct wpa_driver_nl80211_data *'
  695 | struct nl_msg * nl80211_bss_msg(struct i802_bss *bss, int flags, uint8_t cmd)
      |                                 ~~~~~~~~~~~~~~~~~^~~

Fixes: 35ff1affe8 "hostapd: update to 2022-05-08"
Signed-off-by: Andre Heider <a.heider@gmail.com>
2022-12-13 10:54:50 +01:00
Andre Heider
3bc060440a hostapd: remove an unused function from ubus.c
eee80211_frequency_to_channel() isn't used anymore, which is a leftover from:
2a31e9ca97 "hostapd: add op-class to get_status output"

Signed-off-by: Andre Heider <a.heider@gmail.com>
2022-12-13 10:54:50 +01:00
Felix Fietkau
e046500fe9 ath9k: add missing dependency on random core
Reported-by: Hartmut Birr <e9hack@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-12-13 10:25:27 +01:00
Christian Lamparter
19b3b14e54 sunxi: fix 253-sunxi-h5-add-support-for-nanopi-r1s-h5 patch offset
This showed up in the log:
|Hunk #1 succeeded at 555 (offset -83 lines).

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-12-12 09:06:17 +01:00
Tony Butler
1e240f60a5 kernel: modules/lib-lz4: add lz4hc_compress
enable option `CONFIG_CRYPTO_LZ4HC` to match default kernel config

this only adds the `lz4hc_compress` module, and has no effect on the
`lz4_decompress` module which already supports any flavor

Signed-off-by: Tony Butler <spudz76@gmail.com>
2022-12-11 09:32:53 -08:00
Felix Fietkau
03518a1b3a rtl8812au-ct: fix build with newer backports cfg80211 api
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-12-11 09:48:38 +01:00
Chukun Pan
171691500e wolfssl: fix build with /dev/crypto
Backport upstream patch to fix build error when
/dev/crypto enabled.

dc9f46a3be

Fixes: #10944
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
2022-12-11 03:30:14 +01:00
Julio Gonzalez Gil
840ce0a65b umbim: Allow roaming and partner connections
Allow registration if the SIM is roaming or partner mode, by adding two
new options to the protocol.

Until now, such registration failed because umbim returns exit codes 4 and
5 for such situations.

Signed-off-by: Julio Gonzalez Gil <git@juliogonzalez.es>
2022-12-11 03:24:45 +01:00
Nick Hainke
b76bcdb210 libtracefs: update to 1.6.2
378a9dd libtracefs: version 1.6.2
e6daa60 libtracefs: Add unit test to test mounting of tracefs_{tracing,debug}_dir()
32acbbf libtracefs: Have tracefs_{tracing,debug}_dir() mount {tracefs,debugfs} if not mounted

Signed-off-by: Nick Hainke <vincent@systemli.org>
2022-12-11 02:45:28 +01:00
Felix Fietkau
a75a798162 mt76: update to the latest version
ec46d7486ab9 sync with upstream
2575de3aea33 wifi: mt76: mt7921: introduce chanctx support
473cebb3c3e1 wifi: mt76: fix bandwidth 80MHz link fail in 6GHz band
de3e77227f62 wifi: mt76: mt7996: add driver for MediaTek Wi-Fi 7 (802.11be) devices
f0c191a9f6cd wifi: mt76: mt7996: add missing argument in mt7996_queue_rx_skb()
d3838a52df62 wifi: mt76: mt7996: enable use_cts_prot support
98492dff3bec wifi: mt76: mt7996: enable ack signal support
2a41e7a82f86 wifi: mt76: mt7996: add support to configure spatial reuse parameter set
194cb3392829 mt76: mt7915: add missing of_node_put()
f91d6f3b73ac wifi: mt76: mt7921s: fix slab-out-of-bounds access in sdio host
1ce4970d799f wifi: mt76: mt7915: fix mt7915_rate_txpower_get() resource leaks
379f3fc0fc43 wifi: mt76: mt7996: fix insecure data handling of mt7996_mcu_ie_countdown()
233c272f0f86 wifi: mt76: mt7996: fix insecure data handling of mt7996_mcu_rx_radar_detected()
5616c4cc1d5d wifi: mt76: mt7996: fix integer handling issue of mt7996_rf_regval_set()
f9598e6d4c2c wifi: mt76: mt7915: split mcu chan_mib array up
b252d94bd763 wifi: mt76: mt7915: check return value before accessing free_block_num
f1cc3696d725 wifi: mt76: mt7996: check return value before accessing free_block_num
b94ba58fa698 wifi: mt76: mt7915: check the correctness of event data
35843a1670c0 wifi: mt76: mt7915: drop always true condition of __mt7915_reg_addr()
01a256c1dc41 wifi: mt76: mt7996: drop always true condition of __mt7996_reg_addr()
5185bbab8953 wifi: mt76: mt7996: fix endianness warning in mt7996_mcu_sta_he_tlv
eeb6949c4d06 wifi: mt76: mt76x0: fix oob access in mt76x0_phy_get_target_power
063823aba978 wifi: mt76: mt7921: add support to update fw capability with MTFG table
a44109267e4e wifi: mt76: mt7996: fix unintended sign extension of mt7996_hw_queue_read()
be5dbb781068 wifi: mt76: mt7915: fix unintended sign extension of mt7915_hw_queue_read()
adf9042b6f63 wifi: mt76: fix coverity uninit_use_in_call in mt76_connac2_reverse_frag0_hdr_trans()
551201379efe wifi: mt76: move leds field in leds struct
14fbb6d6e85e wifi: mt76: move leds struct in mt76_phy
81edc468fc62 wifi: mt76: mt7915: enable per-phy led support
bbad827e447f wifi: mt76: mt7615: enable per-phy led support
8e7e7e52fc09 wifi: mt76: dma: do not increment queue head if mt76_dma_add_buf fails
95c66d651133 wifi: mt76: handle possible mt76_rx_token_consume failures
52d04463a66e wifi: mt76: dma: rely on queue page_frag_cache for wed rx queues
7fae1de12ae7 wifi: mt76: mt7921: resource leaks at mt7921_check_offload_capability()

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-12-10 15:15:42 +01:00
Felix Fietkau
8d90b9fef1 mac80211: update to linux 6.1-rc8
This should help stay in sync with upstream development

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-12-10 15:15:19 +01:00
Felix Fietkau
b1b29ba987 mt76: update to version 2022-12-01
3deafbad7061 wifi: mt76: mt7915: fix uninitialized irq_mask
6ca31dc64da4 wifi: mt76: mt7921: introduce remain_on_channel support
7962005b0734 wifi: mt76: connac: rework macros for unified command
3b2882ca704e wifi: mt76: connac: update struct sta_rec_phy
c4d46cb1dd45 wifi: mt76: connac: rework fields for larger bandwidth support in sta_rec_bf
532c322fd72f wifi: mt76: connac: add more unified command IDs
4c43e060726b wifi: mt76: connac: introduce unified event table
4c423058920d wifi: mt76: connac: add more bss info command tags
143d7ab8ef92 wifi: mt76: connac: add more starec command tags
733ef9887b2c wifi: mt76: connac: introduce helper for mt7996 chipset
8e309b5560e1 wifi: mt76: mt7921: fix wrong power after multiple SAR set
d791ed1f5877 wifi: mt76: mt7915: add missing MODULE_PARM_DESC
3b8eed9c3866 wifi: mt76: mt7915: add support to configure spatial reuse parameter set
417cca39bab2 wifi: mt76: introduce rxwi and rx token utility routines
629f8631f54f wifi: mt76: add WED RX support to mt76_dma_{add,get}_buf
13c2dc8993b6 wifi: mt76: add WED RX support to mt76_dma_rx_fill
86e94f4162b7 wifi: mt76: add WED RX support to dma queue alloc
1361519851f3 wifi: mt76: add info parameter to rx_skb signature
a2e5e0667553 wifi: mt76: connac: introduce mt76_connac_mcu_sta_wed_update utility routine
f38faf294310 wifi: mt76: mt7915: enable WED RX support
a887a5feb3d1 wifi: mt76: mt7915: enable WED RX stats
4c23061ebcfc wifi: mt76: mt7915: add basedband Txpower info into debugfs
a9c88ded5cac wifi: mt76: mt7915: enable .sta_set_txpwr support
2c172bb6cd9f wifi: mt76: mt7915: fix band_idx usage
1b88dd07f153 linux-firmware: update firmware for MT7915
6196f6080506 linux-firmware: update firmware for MT7916
daae6ca5d81f linux-firmware: update firmware for MT7986
e7a9f7a0440c wifi: mt76: mt7915: fix unused-but-set warning
340f3be65397 wifi: mt76: fix coverity overrun-call in mt76_get_txpower()
aa7132da0326 wifi: mt76: mt7915: fix endianness of mt7915_mcu_set_obss_spr_pd()
a36017d09324 wifi: mt76: mt7921: Add missing __packed annotation of struct mt7921_clc
66dc48bea883 wifi: mt76: do not send firmware FW_FEATURE_NON_DL region
fa79eeeadc2d mt76: mt7915: Fix PCI device refcount leak in mt7915_pci_init_hif2()
ff94604b2edd wifi: mt76: mt7915: introduce mt7915_get_power_bound()
5082a58f8082 wifi: mt76: mt7915: enable per bandwidth power limit support
a7b915302147 wifi: mt76: mt7915: fix scene detection flow of spatial reuse
525592c28d6b wifi: mt76: mt7915: rely on band_idx of mt76_phy
cdd7229e769b wifi: mt76: mt7915: mmio: fix naming convention

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-12-10 13:18:10 +01:00
Felix Fietkau
a797f0e82a hostapd: use wpa_supplicant for unencrypted mesh connections
It's more reliable than using iw

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-12-10 12:38:46 +01:00
Rafał Miłecki
57a8ea6d74 uboot-bcm4908: update to the latest generic
4435700d18 Remove redundant YYLOC global declaration

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2022-12-08 12:10:21 +01:00
Hauke Mehrtens
69f0c29b8b ustream-ssl: update to Git version 2022-12-07
9217ab4 ustream-openssl: Disable renegotiation in TLSv1.2 and earlier
2ce1d48 ci: fix building with i.MX6 SDK
584f1f6 ustream-openssl: wolfSSL: provide detailed information in debug builds
aa8c48e cmake: add a possibility to set library version

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2022-12-08 01:17:26 +01:00
Jan-Niklas Burfeind
13f82ce264 comgt-ncm: add support for quectel modem EC200T-EU
context_type is an integer mapping of pdptype:
1: IPV4
2: IPV6
3: IPV4V6

Signed-off-by: Jan-Niklas Burfeind <git@aiyionpri.me>
2022-12-07 12:30:39 +01:00
Andre Heider
8138d66fcc fritz-tools: fritz_tffs_nand: cache already read sector ids
This speeds up the tool significantly, especially when using the "-a"
argument.

Signed-off-by: Andre Heider <a.heider@gmail.com>
2022-12-07 12:30:23 +01:00
Andre Heider
902378dc87 fritz-tools: fritz_tffs_nand: get rid of struct tffs_sectors
This doesn't help and "[0]" gets in the way of bounds checks.

Signed-off-by: Andre Heider <a.heider@gmail.com>
2022-12-07 12:30:17 +01:00
Andre Heider
4e2d5f4f9f fritz-tools: fritz_tffs_nand: exclude oob code when disabled
Skip unnecessary stuff if checking the oob data is disabled.

Signed-off-by: Andre Heider <a.heider@gmail.com>
2022-12-07 12:30:10 +01:00
Jo-Philipp Wich
f1f3d19387 firewall4: add missing PKG_MIRROR_HASH
Fixes: 84183f0d98 ("firewall4: update to latest Git HEAD")
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2022-12-07 08:54:56 +01:00
Hauke Mehrtens
60e335b76e e2fsprogs: Fix CVE-2022-1304
This fixes CVE-2022-1304:
An out-of-bounds read/write vulnerability was found in e2fsprogs 1.46.5.
This issue leads to a segmentation fault and possibly arbitrary code
execution via a specially crafted filesystem.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2022-12-06 23:09:00 +01:00
Jo-Philipp Wich
84183f0d98 firewall4: update to latest Git HEAD
700a925 fw4: prevent null access when no ipsets are defined
6443ec7 config: drop input traffic by default
119ee1a ruleset: drop ctstate invalid traffic for masq-enabled zones

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2022-12-06 11:43:06 +01:00
Jo-Philipp Wich
86b8e245c8 ucode: update to latest Git HEAD
46d93c9 tests: fixup testcases
4c654df types: adjust double printing format
eac2add compiler: fix bytecode for logical assignments of properties
3903b18 fs: add `realpath()` function
8366102 math: add isnan() function
eef83d3 tests: relax sleep() test
394e901 lib: uc_json(): accept trailing whitespace when parsing strings
1867c8b uloop: terminate parent uloop in task child processes
d2cc003 uci: auto-load package in `ctx.foreach()` and `ctx.get_first()`
6c5ee53 compiler: ensure that arrow functions with block bodies return no value
fdc9b6a compiler: fix `??=`, `||=` and `&&=` logical assignment semantics
88dcca7 add cmake to install requires for debian

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2022-12-06 11:43:06 +01:00
Christian Marangi
ada4d0d0ab
iucode-tool: fix compile error with musl libc and USE_CPUID_DEVICE
Add patch to fix compilation error with USE_CPUID_DEVICE enabled and musl
used as libc. Musl doesn't add limits.h header by default and this is
required if USE_CPUID_DEVICE is used.

The package currently compile because fortify headers include limits.h
by default.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-12-04 13:21:46 +01:00
Hauke Mehrtens
077622a198 mac80211: Update to version 5.15.81
The removed patches were applied upstream.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2022-12-03 18:32:19 +01:00
Daniel Golle
366bcffa0e
uboot-mediatek: bpi-r3: raise CONFIG_LMB_MAX_REGIONS to 64
Raise CONFIG_LMB_MAX_REGIONS to 64 as there are going to be more than
8 (the default value) reserved regions to allow supporting offloading
Wireless-to-Ethernet traffic on MT7986.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-11-29 19:44:43 +00:00
Daniel Golle
aa12a0fdd1
dnsmasq: add option to expose additional paths to jail
Add new UCI list 'addn_mount' allowing the expose additional filesystem
paths to the jailed dnsmasq process. This is useful e.g. in case of
manually configured includes to the configuration file or symlinks
pointing outside of the exposed paths as used by e.g. the safe-search
package in the packages feed.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-11-27 14:06:08 +00:00
Pawel Dembicki
afcccaad82 layerscape: Switch LS1012A-FRDM initramfs to gzip
At this moment LS1012A-FRDM have uncompressed initramfs image.

Error was caused, because gzip extract area overlap image.

Let's change loadaddr and enable gzip initramfs images again.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2022-11-27 13:18:29 +01:00
Michael Pratt
6de9287abd ath79: add support for Senao Engenius EAP1750H
FCC ID: A8J-EAP1750H

Engenius EAP1750H is an indoor wireless access point with
1 Gb ethernet port, dual-band wireless,
internal antenna plates, and 802.3at PoE+

**Specification:**

  - QCA9558 SOC
  - QCA9880 WLAN	PCI card, 5 GHz, 3x3, 26dBm
  - AR8035-A PHY	RGMII GbE with PoE+ IN
  - 40 MHz clock
  - 16 MB FLASH		MX25L12845EMI-10G
  - 2x 64 MB RAM	NT5TU32M16FG
  - UART at J10		populated
  - 4 internal antenna plates (5 dbi, omni-directional)
  - 5 LEDs, 1 button (power, eth0, 2G, 5G, WPS) (reset)

**MAC addresses:**

  MAC addresses are labeled as ETH, 2.4G, and 5GHz
  Only one Vendor MAC address in flash

  eth0 ETH  *:fb art 0x0
  phy1 2.4G *:fc ---
  phy0 5GHz *:fd ---

**Serial Access:**

  the RX line on the board for UART is shorted to ground by resistor R176
  therefore it must be removed to use the console
  but it is not necessary to remove to view boot log

  optionally, R175 can be replaced with a solder bridge short

  the resistors R175 and R176 are next to the UART RX pin at J10

**Installation:**

  2 ways to flash factory.bin from OEM:

  Method 1: Firmware upgrade page:

    OEM webpage at 192.168.1.1
    username and password "admin"
    Navigate to "Firmware Upgrade" page from left pane
    Click Browse and select the factory.bin image
    Upload and verify checksum
    Click Continue to confirm and wait 3 minutes

  Method 2: Serial to load Failsafe webpage:

    After connecting to serial console and rebooting...
    Interrupt uboot with any key pressed rapidly
    execute `run failsafe_boot` OR `bootm 0x9fd70000`
    wait a minute
    connect to ethernet and navigate to
    "192.168.1.1/index.htm"
    Select the factory.bin image and upload
    wait about 3 minutes

**Return to OEM:**

  If you have a serial cable, see Serial Failsafe instructions
  otherwise, uboot-env can be used to make uboot load the failsafe image

  ssh into openwrt and run
  `fw_setenv rootfs_checksum 0`
  reboot, wait 3 minutes
  connect to ethernet and navigate to 192.168.1.1/index.htm
  select OEM firmware image from Engenius and click upgrade

**TFTP recovery:**

  Requires serial console, reset button does nothing

  rename initramfs to 'vmlinux-art-ramdisk'
  make available on TFTP server at 192.168.1.101
  power board, interrupt boot
  execute tftpboot and bootm 0x81000000

  NOTE: TFTP is not reliable due to bugged bootloader
  set MTU to 600 and try many times
  if your TFTP server supports setting block size
  higher block size is better.

**Format of OEM firmware image:**

  The OEM software of EAP1750H is a heavily modified version
  of Openwrt Kamikaze. One of the many modifications
  is to the sysupgrade program. Image verification is performed
  simply by the successful ungzip and untar of the supplied file
  and name check and header verification of the resulting contents.
  To form a factory.bin that is accepted by OEM Openwrt build,
  the kernel and rootfs must have specific names...

    openwrt-ar71xx-generic-eap1750h-uImage-lzma.bin
    openwrt-ar71xx-generic-eap1750h-root.squashfs

  and begin with the respective headers (uImage, squashfs).
  Then the files must be tarballed and gzipped.
  The resulting binary is actually a tar.gz file in disguise.
  This can be verified by using binwalk on the OEM firmware images,
  ungzipping then untaring.

  Newer EnGenius software requires more checks but their script
  includes a way to skip them, otherwise the tar must include
  a text file with the version and md5sums in a deprecated format.

  The OEM upgrade script is at /etc/fwupgrade.sh.

  OKLI kernel loader is required because the OEM software
  expects the kernel to be no greater than 1536k
  and the factory.bin upgrade procedure would otherwise
  overwrite part of the kernel when writing rootfs.

Note on PLL-data cells:

  The default PLL register values will not work
  because of the external AR8035 switch between
  the SOC and the ethernet port.

  For QCA955x series, the PLL registers for eth0 and eth1
  can be see in the DTSI as 0x28 and 0x48 respectively.
  Therefore the PLL registers can be read from uboot
  for each link speed after attempting tftpboot
  or another network action using that link speed
  with `md 0x18050028 1` and `md 0x18050048 1`.

  The clock delay required for RGMII can be applied
  at the PHY side, using the at803x driver `phy-mode`.
  Therefore the PLL registers for GMAC0
  do not need the bits for delay on the MAC side.
  This is possible due to fixes in at803x driver
  since Linux 5.1 and 5.3

Signed-off-by: Michael Pratt <mcpratt@pm.me>
2022-11-27 13:18:29 +01:00
Nick Hainke
6640c788fe mac80211: subsys: complete patch files for use with git am
Adding proper fields to patch files allowing for `git am` to properly
function.

Signed-off-by: Nick Hainke <vincent@systemli.org>
2022-11-27 13:18:29 +01:00
Tony Butler
3d205eb216 wolfssl: fix Config.in typo
Fix simple typo `/crytpo/crypto/` in a description string

Signed-off-by: Tony Butler <spudz76@gmail.com>
2022-11-27 12:58:33 +01:00
Nick Hainke
745f1ca976 wolfssl: update to v5.5.3
Remove "200-ecc-rng.patch" because it was upstramed by:
e2566bab21
Refreshed "100-disable-hardening-check.patch".

Fixes CVE 2022-42905.

Release Notes:
- https://github.com/wolfSSL/wolfssl/releases/tag/v5.5.2-stable
- https://github.com/wolfSSL/wolfssl/releases/tag/v5.5.3-stable

Signed-off-by: Nick Hainke <vincent@systemli.org>
2022-11-27 12:58:33 +01:00
Nick Hainke
68714f2135 ipset: update to 7.16
Release Notes:
https://lore.kernel.org/netfilter-devel/d65fe5d8-d5ea-ef7-102d-aa1d15bb4d69@netfilter.org/T/#u

Patch "0001-lib-ipset-fix-printf-warning.patch" replaced upstream by:
http://git.netfilter.org/ipset/commit/?id=e39e3466d2d38cdfe83447f391b550e607bc3ce8

Remove upstreamed:
- 0002-Fix-IPv6-sets-nftables-translation.patch

Signed-off-by: Nick Hainke <vincent@systemli.org>
2022-11-27 12:58:33 +01:00
Alexander Couzens
4943ce98ff
kernel/module/iio: add TI am335x ADC driver
Add the iio driver for the embedded ADC in the
TI Sitara am335x SoCs.

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
2022-11-24 15:47:01 +00:00
Jonas Albrecht
74a5718223 lantiq: ltq-tapi: add customer pulse digit time
With this patch you can change the pulse digit time by loading the Lantiq
FXS driver kernel module called ltq-tapi. This is relevant for old
rotaryphones that uses pulsedialing.

The default values are:
30-80ms for the low pulse
30-80ms for the high pulse
300ms for minimum Interdigit time

this is OK but on some Phones it can be usefull to customize the values
If you want to change the values to high and low pulse to 40-90ms and
minimum interdigit time to 400ms

than change /etc/modules.d/20-ltq-tapi to (without linebrakes):
drv_tapi min_digit_low=40  min_digit_high=90 max_digit_low=40 \
max_digit_high=90 min_interdigit=400

Signed-off-by: Jonas Albrecht <plonkbong100@protonmail.com>
2022-11-18 20:27:52 +01:00
Nick Hainke
8db2db9890 libtracefs: update to 1.6.1
Update to latest version.

Signed-off-by: Nick Hainke <vincent@systemli.org>
2022-11-18 20:27:52 +01:00
Nick Hainke
c17b6343f3 lldpd: update to 1.0.16
Release Notes:
https://github.com/lldpd/lldpd/releases/tag/1.0.16

Signed-off-by: Nick Hainke <vincent@systemli.org>
2022-11-18 20:27:52 +01:00
Álvaro Fernández Rojas
1996d600bd cypress-firmware: update to v5.10.9-2022_0909
The following firmwares have been updated:
- cyfmac43012-sdio (v13.10.271.266 -> v13.10.271.289)
- cyfmac43430-sdio (v7.45.98.118 -> v7.45.98.125)
- cyfmac43455-sdio (v7.45.234 -> v7.45.250)
- cyfmac4354-sdio (v7.35.349.104 -> v7.35.349.117)
- cyfmac4356-pcie (v7.35.180.208 -> v7.35.180.212)
- cyfmac4356-sdio (v7.35.349.104 -> v7.35.349.115)
- cyfmac4373-sdio (v13.10.246.253 -> v13.10.246.289)
- cyfmac4373-usb (v13.10.246.253 -> v13.10.246.289)
- cyfmac54591-pcie (v13.35.225 -> v13.35.284)

The following firmwares have been added:
- cyfmac43439-sdio (v7.95.55)
- cyfmac4373-pcie (v13.35.205.66)
- cyfmac54591-sdio (v13.35.284)
- cyfmac55560-pcie (v18.53.53.4)
- cyfmac55572-pcie (v18.53.117.2)
- cyfmac55572-sdio (v18.53.117.2)

More info: https://github.com/Infineon/ifx-linux-firmware/compare/release-v5.4.18-2021_0812...release-v5.10.9-2022_0909

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2022-11-17 16:43:55 +01:00
Álvaro Fernández Rojas
0db537975d cypress-firmware: fix cyfmac4356-pcie symbolic links
The symbolic link introduced in 22e9d8bc89 is wrong.

Fixes: 22e9d8bc89 ("cypress-firmware: use symlink to provide firmware in brcm")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2022-11-17 12:27:41 +01:00
Daniel Golle
4c67d1e066 uboot-mediatek: optimize MMC erase
Fix mmc_write_vol hush script used by many boards to avoid timeouts on
slow SD cards:
Instead of erasing a complete partition, only erase blocks for the
to-be-written image when writing to MMC.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-11-17 01:55:55 +00:00
Kuan-Yi Li
49bbfd9968 cypress-nvram: consolidate NVRAM packages
NVRAM packages for the same wireless chip are consolidated into one as
they contain only small text files and symlinks.

Signed-off-by: Kuan-Yi Li <kyli@abysm.org>
2022-11-16 20:14:13 +01:00
Kuan-Yi Li
c6e86d8095 linux-firmware: broadcom: consolidate NVRAM packages
NVRAM packages for the same wireless chip are consolidated into one as
they contain only small text files and symlinks.

Signed-off-by: Kuan-Yi Li <kyli@abysm.org>
2022-11-16 20:14:13 +01:00
Kuan-Yi Li
22fd8b0df6 cypress-nvram: disassociate from external source repo
Since all NVRAM files in external repo are now upstreamed and to lower
future maintenance cost, disassociate the package from external source
repo.

All upstream pending NVRAM files shall be stored locally from now on.

Signed-off-by: Kuan-Yi Li <kyli@abysm.org>
[Remove outdated URL, add SPDX-License-Identifier]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2022-11-16 20:14:13 +01:00
Glenn Strauss
0d43c22d47 libmbedtls: use defaults if no build opts selected
use defaults if no build opts selected
(allows build with defaults when mbedtls not selected and configured)

Signed-off-by: Glenn Strauss <gstrauss@gluelogic.com>
2022-11-16 12:27:18 +02:00
Kuan-Yi Li
a110418027 linux-firmware: offer two versions of firmware for CYW4339
According to commit 6f6c2fb321, AP6335 module used in PICO-PI-IMX7D works
only with firmware from `linux-firmware`. However, firmware from
`cypress-firmware` suite is directly from the chip company (Infineon) and
is actually newer.

Instead of dropping the firmware from Infineon, create a package named
`brcmfmac-firmware-4339-sdio`, and keep the Infineon version of
`cypress-firmware-4339-sdio` around.

This gives us devs the option to choose. Also, it means that

 - packages `brcmfmac-firmware-*` uniformly come from `linux-firmware`
 - packages `cypress-firmware-*` uniformly come from `cypress-firmware`

so hopefully brings more clarity.

Tested-by: Lech Perczak <lech.perczak@gmail.com>
Signed-off-by: Kuan-Yi Li <kyli@abysm.org>
2022-11-15 20:49:58 +01:00
Kuan-Yi Li
60832584aa linux-firmware: broadcom: use symlink to provide NVRAM for some RPis
This is to align the implementation with upstream `linux-firmware`.

Some Raspberry Pi boards do not have dedicated NVRAM in `linux-firmware`
source repository, their NVRAM is provided through a symbolic link to
NVRAM of another board with an identical wireless design.

Signed-off-by: Kuan-Yi Li <kyli@abysm.org>
2022-11-15 20:48:20 +01:00