The gpio is actually low active, fix it.
Fixes: 40e7fab9e4 ("mediatek: add Nokia EA0326GMP support")
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/15651
Signed-off-by: Robert Marko <robimarko@gmail.com>
containing fixes around tar and internal checksums.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Link: https://github.com/openwrt/openwrt/pull/15646
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Commit ae8bf1a26e ("imx: add imx8m support") configured the
drm-imx-ldb kmod for imx_cortexa9 and imx_cortexa7 however it is only
applicable to imx_cortexa9 (imx6).
Fix this so that we can avoid a missing module config for cortexa7 when
moving to the 6.6 kernel.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Hardware specification:
SoC: MediaTek MT7981B 2x A53
Flash: 128 MB SPI-NAND
RAM: 256MB
Ethernet: 4x 10/100/1000 Mbps
Switch: MediaTek MT7531AE
WiFi: MediaTek MT7976C
Button: Reset, WPS/Mesh
Power: DC 12V 1A
Gain SSH access:
1. Login into web interface, and download the configuration.
2. Download the configration utilities:
https://firmware.download.immortalwrt.eu.org/cnsztl/mediatek/filogic/openwrt-mediatek-mt7981-nokia-ea0326gmp-config-utils.tar.gz
These binaries are extraced from the factory firmware, which are
dynamically linked with aarch64 musl 1.1.24. To use them, you
must run them under the same runtime environment, otherwise the
binaries will not work properly!
3. Upload the configuration and utilities to a suitable environment.
4. Uncompress the utilities, move them to '/bin' and give them executable permisison:
tar -zxf openwrt-mediatek-mt7981-nokia-ea0326gmp-config-utils.tar.gz
mv mkconfig seama /bin
chmod +x /bin/mkconfig
chmod +x /bin/seama
5. Decrypt and uncompress the configuration:
Enter fakeroot if you are not login as root.
mkconfig -a de-enca -m EA0326GMP_3FE79221BAAA -i EA0326GMP_3FE79221BAAA-xxxxxxxx-backup.tar.gz -o backup.tar.gz
tar -zxf backup.tar.gz
6. Edit 'etc/config/dropbear', set 'enable' to '1'.
7. Edit 'etc/passwd', remove root password: 'root::1:0:99999:7:::'.
8. Repack the configuration:
tar -zcf backup.tar.gz etc/
mkconfig -a enca -m EA0326GMP_3FE79221BAAA -i backup.tar.gz -o EA0326GMP_3FE79221BAAA-xxxxxxxx-backup.tar.gz
9. Upload new configuration via web interface, now you can SSH to EA0326GMP.
A minimum configuration which enabled SSH access is also provided
to simplify the process:
https://firmware.download.immortalwrt.eu.org/cnsztl/mediatek/filogic/openwrt-mediatek-mt7981-nokia-ea0326gmp-enable-ssh.tar.gz
Flash instructions:
1. SSH to EA0326GMP, backup everything, especially 'Factory' part.
2. Write new BL2:
mtd write openwrt-mediatek-filogic-nokia_ea0326gmp-preloader.bin BL2
3. Write new FIP:
mtd write openwrt-mediatek-filogic-nokia_ea0326gmp-bl31-uboot.fip FIP
4. Set static IP on your PC:
IP 192.168.1.254/24, GW 192.168.1.1
5. Serve OpenWrt initramfs image using TFTP server.
6. Cut off the power and re-engage, wait for TFTP recovery to complete.
7. After OpenWrt has booted, perform sysupgrade.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Dont allow x2 read and cache read operations on FM35Q1GA as they seem
to be unstable. Also the Linux drivers does not allow x2 ops.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Import pending patches to set pinconf settings for SPI-NAND pins on
MT7622 identical to what the old proprietary preloader did.
Should further increase the reliability of some SNFI-attached SPI-NAND
flash chips.
Link: https://github.com/mtk-openwrt/arm-trusted-firmware/pull/7
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Update ARM TrustedFirmware-A to the most recent release of
MediaTek downstream patched version released 2024-01-17.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Enable trx feature of mtd command to fixup trx length and crc32 while
booting for some Buffalo devices.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Use the same Yafut code revision for both updating devices with NAND
flash and preparing firmware images for devices with NOR flash.
Signed-off-by: Michał Kępień <openwrt@kempniu.pl>
Link: https://github.com/openwrt/openwrt/pull/13453
Signed-off-by: Robert Marko <robimarko@gmail.com>
There are too many RTC drivers in other.mk, they deserve their
own menu and .mk-file, so let's break them out to a separate
entity.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
U-Boot 2024.04 for tegra needs swig installed on the host, this
dependency is only checked if UBOOT_USE_INTREE_DTC is set. add the
missing definition.
Fixes: 6832faf340 ("uboot-tegra: bump version to 2024.04")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Split the kmod-video-dma into kmod-video-dma-sg and
kmod-video-dma-contig. The old one contained two kmods, but sometimes
only one of them is build which caused problems. The configuration
options are not manually selectable in the kernel and hidden in OpenWrt.
Currently this causes build failures on some targets.
Fixes: 4d7cbe0a55 ("kernel: video-dma: explicitly state packaged modules")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Dual-slot NAS based on Marvell Kirkwood.
Specifications:
- Marvell 88F6702 @1GHz
- 256Mb RAM
- 128Mb NAND
- 1x GbE LAN (Marvell 88E1318R)
- 1x USB 2.0
- 2x SATA
- Weltrend WT69P3 ("supervisor" MCU chip)
- Serial on J2 (115200,8n1)
- Newer bootROM so kwboot-ing via serial is possible
Notes:
- The Weltrend MCU is controlled by the package added in utils/dns320l-mcu.
- The original MAC address is stored in the "mini firmware" image's first
17 bytes.
- Compared to the original MTD layout, the uImage+rootfs are now stored in
a common ubi partition.
Installation:
1. Serial console
- Connect your levelshifter to the serial console
on J2 (refer to the wiki page for pinout)
2. Update u-boot
- Download the u-boot.kwb image for the device
- Powercycle the NAS
- Run "kwboot -b u-boot-dns320l/u-boot.kwb /dev/ttyUSB0 -p"
- Connect to the serial console with minicom
- tftp 0x0800000 u-boot-dns320l/u-boot.kwb
(Please note that "PHY reset timed out" seems to be customary
on kirkwood devices, the egiga0 interface works regardless.)
- nand erase 0x0 100000
- nand write 0x0800000 0x0 0x100000
- reset
3. Install OpenWrt
- Boot up the initramfs image
- tftpboot 0x800000 openwrt-kirkwood-generic-dlink_dns320l-initramfs-uImage; bootm 0x800000
- Download the sysupgrade image and perform sysupgrade
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Reviewed-by: Pawel Dembicki <paweldembicki@gmail.com>
Because wildcard in variable stating packaged modules, the filtering for
built-in kernel modules didn't work and would cause a packaging failure.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
ply is a light-weight dynamic tracer for Linux that leverages the kernel's
BPF VM in concert with kprobes/tracepoints to attach probes to arbitrary
points in the kernel.
Most tracers that generate BPF bytecode are based on the LLVM-based BCC
toolchain; ply on the other hand has no external dependencies outside libc,
making it suitable for use on constrained embedded systems.
Currently ply supports x86_64, aarch64, arm, riscv64, riscv32, powerpc,
mips(el), and mips64(el) architectures.
Further documentation, examples and implementation details may be found at:
https://github.com/iovisor/ply.
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
At least kmod-fb-tft depends on CONFIG_FB_DEVICE and can not be
activated without it.
This configuration option was added with kernel 6.6, before this featre
was always activated.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Support for iptables action has been dropped. Remove tc-mod-iptables and related
patch (175-reduce-dynamic-syms.patch).
We also add the missing libbpf dependency for `ss` since iproute 8740ca9
("ss: add support for BPF socket-local storage") now means that `ss` requires
libbpf as well.
Fix 170-ip_tiny.patch, as the help text didn't match all the included functions.
Drop upstreamed patches 402-bpf-fix-warning-from-basename.patch
and 403-bpf-include-libgen.h-for-basename.patch.
All other patches automatically rebased.
Co-authored-by: Rany Hany <rany_hany@riseup.net>
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Signed-off-by: Rany Hany <rany_hany@riseup.net>
Upstream patches:
401-bridge-vlan.c-bridge-vlan.c-fix-build-with-gcc-14-on.patch
402-bpf-fix-warning-from-basename.patch
403-bpf-include-libgen.h-for-basename.patch
The patch (400-rdma-include-libgen.h-for-basename.patch) was not
submitted upstream but just adds a missing include for basename.
Signed-off-by: Rany Hany <rany_hany@riseup.net>
Without this patch, GCC 14 incorrectly complains about the following error:
In file included from /home/user/workspace/mbedtls/library/ctr_drbg.c:13:
In function ‘mbedtls_xor’,
inlined from ‘ctr_drbg_update_internal’ at /home/user/workspace/mbedtls/library/ctr_drbg.c:372:5:
/home/user/workspace/mbedtls/library/common.h:235:17: error: array subscript 48 is outside array bounds of ‘unsigned char[48]’ [-Werror=array-bounds=]
235 | r[i] = a[i] ^ b[i];
| ~^~~
/home/user/workspace/mbedtls/library/ctr_drbg.c: In function ‘ctr_drbg_update_internal’:
/home/user/workspace/mbedtls/library/ctr_drbg.c:335:19: note: at offset 48 into object ‘tmp’ of size 48
335 | unsigned char tmp[MBEDTLS_CTR_DRBG_SEEDLEN];
| ^~~
In function ‘mbedtls_xor’,
inlined from ‘ctr_drbg_update_internal’ at /home/user/workspace/mbedtls/library/ctr_drbg.c:372:5:
/home/user/workspace/mbedtls/library/common.h:235:24: error: array subscript 48 is outside array bounds of ‘const unsigned char[48]’ [-Werror=array-bounds=]
235 | r[i] = a[i] ^ b[i];
| ~^~~
/home/user/workspace/mbedtls/library/ctr_drbg.c: In function ‘ctr_drbg_update_internal’:
/home/user/workspace/mbedtls/library/ctr_drbg.c:333:57: note: at offset 48 into object ‘data’ of size [0, 48]
333 | const unsigned char data[MBEDTLS_CTR_DRBG_SEEDLEN])
| ~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
In function ‘mbedtls_xor’,
inlined from ‘ctr_drbg_update_internal’ at /home/user/workspace/mbedtls/library/ctr_drbg.c:372:5:
/home/user/workspace/mbedtls/library/common.h:235:14: error: array subscript 48 is outside array bounds of ‘unsigned char[48]’ [-Werror=array-bounds=]
235 | r[i] = a[i] ^ b[i];
| ~~~~~^~~~~~~~~~~~~
/home/user/workspace/mbedtls/library/ctr_drbg.c: In function ‘ctr_drbg_update_internal’:
/home/user/workspace/mbedtls/library/ctr_drbg.c:335:19: note: at offset 48 into object ‘tmp’ of size 48
335 | unsigned char tmp[MBEDTLS_CTR_DRBG_SEEDLEN];
| ^~~
This change adds a basic check to silence the warning until a solution is worked on upstream.
As this check is already used by another compiler, it shouldn't cause any issues for us.
Signed-off-by: Rany Hany <rany_hany@riseup.net>
Remove 100-musl_fix.patch, which is no longer needed
and causes a build error with gcc-14.
Fixes:
useful_functions.c:63:41: error: passing argument 1 of 'ether_ntoa' from incompatible pointer type [-Wincompatible-pointer-types]
63 | printf("%s", ether_ntoa((struct ether_addr *) mac));
| ^~~~~~~~~~~~~~~~~~~~~~~~~
| |
| struct ether_addr *
In file included from include/ebtables_u.h:28,
from useful_functions.c:25:
/Volumes/wrt3200/openwrt/staging_dir/toolchain-arm_cortex-a9+vfpv3-d16_gcc-14.1.0_musl_eabi/include/netinet/ether.h:10:19: note: expected 'const struct ether_addr *' but argument is of type 'struct ether_addr *'
10 | char *ether_ntoa (const struct ether_addr *);
| ^~~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Georgi Valkov <gvalkov@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15576
Signed-off-by: Robert Marko <robimarko@gmail.com>
Dell/SonicWall APL26-0AE (marketed as SonicPoint ACe) is a dual band
wireless access point. End of life as of 2022-07-31.
Specification
SoC: QualcommAtheros QCA9550
RAM: 256 MB DDR2
Flash: 32 MB SPI NOR
WIFI: 2.4 GHz 3T3R integrated
5 GHz 3T3R QCA9890 oversized Mini PCIe card
Ethernet: 2x 10/100/1000 Mbps QCA8334
port labeled lan1 is PoE capable (802.3at)
USB: 1x 2.0
LEDs: LEDs: 6x which 5 are GPIO controlled and two of them are dual color
Buttons: 2x GPIO controlled
Serial: RJ-45 port, SonicWall pinout
baud: 115200, parity: none, flow control: none
Before flashing, be sure to have a copy of factory firmware, in case You
wish to revert to original firmware.
All described procedures were done in following environment:
ROM Version: SonicROM (U-Boot) 8.0.0.0-11o
SafeMode Firmware Version: SonicOS 8.0.0.0-14o
Firmware Version: SonicOS 9.0.1.0
In case of other versions, following installation instructions might be
ineffective.
Installation
1. Prepare TFTP server with OpenWrt sysupgrade image and rename that
image to "sp_fw.bin".
2. Connect to one of LAN ports.
3. Connect to serial port.
4. Hold the reset button (small through hole on side of the unit),
power on the device and when prompted to stop autoboot, hit any key.
The held button can now be released.
5. Alter U-Boot environment with following commands:
setenv bootcmd bootm 0x9F110000
saveenv
6. Adjust "ipaddr" (access point, default is 192.168.1.1) and "serverip"
(TFTP server, default is 192.168.1.10) addresses in U-Boot
environment, then run following commands:
tftp 0x80060000 sp_fw.bin
erase 0x9F110000 +0x1EF0000
cp.b 0x80060000 0x9F110000 $filesize
7. After successful flashing, execute:
boot
8. The access point will boot to OpenWrt. Wait few minutes, until the
wrench LED will stop blinking, then it's ready for configuration.
Known issues
Initramfs image can't be bigger than specified kernel size, otherwise
bootloader will throw LZMA decompressing error. Switching to lzma-loader
should workaround that.
This device has Winbond 25Q256FVFG and doesn't have reliable reset, which
causes hang on reboot, thus broken-flash-reset needs to be added. This
property addition causes dispaly of "scary" warning on each boot, take
this warnig into consideration.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
This commit adds a new mlxreg package, which allows access
to Mellanox programmable device register space through sysfs
interface for thermal control and hardware management.
It also adds required Mellanox I²C drivers and packages
for the "special" MSN4800 series and SN2201 platform.
Signed-off-by: Til Kaiser <mail@tk154.de>
Add support for ELECOM WRC-X1800GS on uboot-envtools, to update
bootmenu_delay variable on sysupgrade.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Common specifications:
* Mediatek MT7988A (4x Cortex-A73, up to 1.8 GHz clock speed)
* 8 GiB eMMC
* 2 GiB DDR4 RAM
* 1x 10000M/1000M/100M + 3x 1000M/100M/10M LAN ports
* MT7996 Tri-band (2.4G, 5G, 6G) 4T4R 802.11be Wi-Fi
* Airoha AG3352 GPS
* Renesas DA14531MOD Bluetooth
* 2 buttons (Reset, Mesh/WPS)
* uC-controlled RGB LED via I2C
* 2x LED for each 1G port, 3x LED for each 10G port
* USB 3.0 type A port
* 3.3V-level 115200 baud UART console via 4-pin Dupont connector
exposed at the bottom of the device
* USB-C PD power input
SDG-8733: 1x 10000M/1000M/100M WAN port
SDG-8734: 1x USXGMII/10GBase-R/5GBase-R/2500Base-X/1000Base-X/SGMII SFP+
Both models are also available in versions including 2x FXS POTS interfaces
for analog phones. Those interfaces are not supported by OpenWrt.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Basic changes to make linux-atm build without any issues with GCC 14.
Besides some errors caused by -Wpointer-sign, there was also an issue
with socklen_t not being used for getsockopt() and accept()
sometimes.
I also updated the Debian patch to include the latest changes from
version "1:2.5.1-5.1" in Debian Sid. This allowed me to drop
"600-fix-format-errors.patch" and "700-include_sockios.patch".
Signed-off-by: Rany Hany <rany_hany@riseup.net>
This 4G/LTE modem is a WiFi hotspot, and also works as cdc_ether modem
when plugged over USB. It needs usb-modeswitching. With HuaweiNewMode,
it will modeswitch from 3426:1f01 (mass-storage) to 3426:14db
(cdc_ether).
Signed-off-by: Didier 'OdyX' Raboud <odyx@raksha.ch>
Link: https://github.com/openwrt/openwrt/pull/15497
Signed-off-by: Robert Marko <robimarko@gmail.com>
Other than OPKG which only uses signed package list, APK uses
individually signed packages in addition to signed package lists. Hence,
in order to be able to generate package, the private key needs to be
generated before compiling packages. Express that dependency and
generate the private key before building any packages instead of doing
so as part of the base-files package build.
Fixes: d788ab376f ("build: add APK package build capabilities")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This commit adds support for Netgear Orbi Pro SXR80 and SXS80 (collectively known as SXK80)
Specifications:
---------------
* CPU: Qualcomm IPQ8074A Quad core Cortex-A53
* RAM: 1024MB
* Storage: SPI-NAND 512 MiB (Winbond W29N04GZ)
* Ethernet: 4x 1G RJ45 ports (QCA8075) 1x 2.5G RJ45 LAN/WAN (QCA8081)
* WLAN:
- 2.4 GHz: Qualcomm QCN5024 4x4
- 2x 5 GHz: Qualcomm QCN5054 4x4 (second radio high channels only)
* LEDs:
- Power: (Green and red)
- Front: (Blue, green, red and white)
* Buttons:
- 1x Soft reset
- 1x Sync/WPS
* Power: 12V DC Jack
Installation instructions (Telnet):
-----------------------------------
*Note, this guide assumes SXR80, for SXS80 change the firmware file name as appropriate
1. Put firmware file openwrt-qualcommax-ipq807x-netgear_sxr80-initramfs-uImage.itb in root of TFTP server available at 192.168.1.10.
2. Enable telnet by going to http://[ip of device]/debug.htm and clicking on the tickbox 'Enable telnet'
3. Telnet into the device and login using the same username and password as the web interface:
4. Run the following command:
`fw_setenv bootcmd 'env default -a; saveenv; reset'`
5. Reboot the router, once the web interface is available again re-enable telnet via http://[ip of device]/debug.htm and telnet into the device.
6. Run the following command:
`fw_printenv`
It should look similar to the below:
```
baudrate=115200
bootargs=console=ttyMSM0,115200n8
bootcmd=mii write 0x0 0x0 0x800; sleep 1; nmrp; bootdni; boot_DNI_secureboot
bootdelay=2
ipaddr=192.168.1.1
netmask=255.255.255.0
serverip=192.168.1.10
soc_version_major=2
soc_version_minor=0
```
**If you see the message:**
`Warning: Bad CRC, using default environment`
**DO NOT CONTINUE, YOU WILL BRICK YOUR DEVICE**
7. Run the following command:
`fw_setenv originalboot 'mii write 0x0 0x0 0x800; sleep 1; nmrp; bootdni; boot_DNI_secureboot'`
(This should match what's in the bootcmd variable displayed in step 6)
8. Run the following commands:
```
fw_setenv wrttftp 'mii write 0x0 0x0 0x800; sleep 1; nmrp; if tftpboot openwrt-qualcommax-ipq807x-netgear_sxr80-initramfs-uImage.itb; then bootm; fi; bootdni; boot_DNI_secureboot'
fw_setenv wrtboot 'mii write 0x0 0x0 0x800; sleep 1; nmrp; nand read 0x40000000 0x1980000 0x06d00000; bootm 0x40000000'
fw_setenv bootcmd 'run wrttftp'
```
9. Ensure SXR/S device is attached via ethernet (LAN port) to the same ethernet segment as the TFTP server.
10. Reboot the device, it should reboot into OpenWrt and be available on 192.168.1.1
11. Once OpenWrt has booted, update the bootcmd using the following command:
`fw_setenv bootcmd 'run wrtboot'`
12. Flash the sysupgrade image
13. It should boot into OpenWrt
References to SXK80 GPL source:
https://www.downloads.netgear.com/files/GPL/SXK80-V3.2.0.108_gpl_src.tar.bz2.zip
Signed-off-by: Flole Systems <flole@flole.de>
Signed-off-by: Andrew Smith <gul.code@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/14939
Signed-off-by: Robert Marko <robimarko@gmail.com>
During the last update to 12.5.r2 printing of the attached PHY-s was
removed, so lets bring it back as it is very helpfull for debugging
OpenWrt issues without users having to modify NSS-DP to know if a PHY
was attached.
Refresh patches since nss_dp_main.c was edited.
Link: https://github.com/openwrt/openwrt/pull/15537
Signed-off-by: Robert Marko <robimarko@gmail.com>
The IXP4xx is well supported upstream and can readily be
supported with kernel v6.6. To simplify things after the
DTS directory was renamed, switch to v6.6 only.
Bring in some outstanding patches.
Tested on the Gateworks GW2348-4.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Changes:
73529a8 Revert "wireless-regdb: Update and disable 5470-5730MHz band according to TPC requirement for Singapore (SG)"
87941e4 wireless-regdb: Update regulatory rules for Taiwan (TW) on 6GHz
33797ae wireless-regdb: update regulatory database based on preceding changes
Signed-off-by: Yuu Toriyama <PascalCoffeeLake@gmail.com>
Add ubi volumes for mt7988a-rfb and support for using factory data
for Ethernet MAC addresses and MT7996 WLAN calibration data.
Also add rootdisk handle. Removes the need to keep using nmbm
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Drop downstream mbedtls patch since it went upstream.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Link: https://github.com/openwrt/openwrt/pull/15522
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The function incorrectly tried to APK keys even if there were none.
Correctly separate it into its own `ifdef` section.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Link: https://github.com/openwrt/openwrt/pull/15519
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The host build would need Lua to compile which currently adds a race
condition. Instead of tracking that down just disable helptext for the
host build.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Both package managers work slightly different, i.e. stores files at
different places. Modify the `functions.sh` file to cover those.
Signed-off-by: Paul Spooren <mail@aparcar.org>
The APK package manager does not support handling of package
alternatives itself, so implement it via a simple shell script.
Signed-off-by: Paul Spooren <mail@aparcar.org>
A new option called `USE_APK` is added which generated APK packages
(.apk) instead of OPKG packages (.ipk).
Some features like fstools `snapshot` command are not yet ported
Signed-off-by: Paul Spooren <mail@aparcar.org>
Since swig is mentioned as build dependency and buildbots have it
installed we can safely bump version.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Hardware specification:
========
SoC: Qualcomm IPQ8072A
Flash: 512MB (Fidelix FMND4G08S3J-ID)
RAM: 1GB (2x Kingston DDR3L D2516ECMDXGJD)
Ethernet: 1x 10/100/1000/2500/5000Mbps (Marvell AQR114C)
Ethernet: 4x 10/100/1000Mbps (Qualcomm QCA8075)
WiFi1: 6GHz ax 4x4 (Qualcomm QCN9024 + Skyworks SKY85784-11) - channels 33-229
WiFi2: 5GHz ax 4x4 (Qualcomm QCN5054 + Skyworks SKY85755-11) - channels 36-177
WiFi3: 2.4GHz ax 4x4 (Qualcomm QCN5024 + Skyworks SKY8340-11)
IoT: Bluetooth 5, Zigbee and Thread (NXP K32W041)
LED: 1x RGB status (NXP PCA9633)
USB: 1x USB 3.0
Button: WPS, Reset
Flash instructions:
========
1. Manually upgrade firmware using openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin image.
More details can be found here: https://www.linksys.com/support-article?articleNum=47547
After first boot check actual partition:
- fw_printenv -n boot_part
and install firmware on second partition using command in case of 2:
- mtd -r -e kernel -n write openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin kernel
and in case of 1:
- mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin alt_kernel
2. Installation using serial connection from OEM firmware (default login: root, password: admin):
- fw_printenv -n boot_part
In case of 2:
- flash_erase /dev/mtd21 0 0
- nandwrite -p /dev/mtd21 openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin
or in case of 1:
- flash_erase /dev/mtd23 0 0
- nandwrite -p /dev/mtd23 openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin
After first boot install firmware on second partition:
- mtd -r -e kernel -n write openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin kernel
or:
- mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin alt_kernel
3. Installation from initramfs image using USB drive:
Put the initramfs image on the USB drive:
- dd bs=1M if=openwrt-qualcommax-ipq807x-linksys_mx8500-initramfs-uImage.itb of=/dev/sda
Stop u-boot and run:
- usb start && usbboot $loadaddr 0 && bootm $loadaddr
Write firmware to the flash from initramfs:
- mtd -e kernel -n write openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin kernel
and:
- mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin alt_kernel
4. Back to the OEM firmware:
- mtd -e kernel -n write FW_MX8500_1.0.11.208937_prod.img kernel
and:
- mtd -r -e alt_kernel -n write FW_MX8500_1.0.11.208937_prod.img alt_kernel
5. USB recovery:
Put the initramfs image on the USB:
- dd bs=1M if=openwrt-qualcommax-ipq807x-linksys_mx8500-initramfs-uImage.itb of=/dev/sda
Set u-boot env:
- fw_setenv bootusb 'usb start && usbboot $loadaddr 0 && bootm $loadaddr'
- fw_setenv bootcmd 'run bootusb; if test $auto_recovery = no; then bootipq; elif test $boot_part = 1; then run bootpart1; else run bootpart2; fi'
AQR firmware:
========
1. Firmware loading:
To properly load the firmware and initialize AQR PHY, we must use the u-boot aq_load_fw function.
To do this, you need to modify u-boot env:
With USB recovery:
- fw_setenv bootcmd 'aq_load_fw; run bootusb; if test $auto_recovery = no; then bootipq; elif test $boot_part = 1; then run bootpart1; else run bootpart2; fi'
and without:
- fw_setenv bootcmd 'aq_load_fw; if test $auto_recovery = no; then bootipq; elif test $boot_part = 1; then run bootpart1; else run bootpart2; fi'
2. Firmware updating:
Newer firmware (AQR-G4_v5.6.5-AQR_WNC_SAQA-L2_GT_ID45287_VER24005.cld) is available in the latest OEM firmware.
To load this firmware via u-boot, we need to add the MBN header and update 0:ethphyfw partition.
For MBN header we can use script from this repository: https://github.com/testuser7/aqr_mbn_tool
- python aqr_mbn_tool.py AQR-G4_v5.6.5-AQR_WNC_SAQA-L2_GT_ID45287_VER24005.cld
To update partition we need to install kmod-mtd-rw package first:
- insmod mtd-rw.ko i_want_a_brick=1
- mtd -e /dev/mtd26 -n write aqr_fw.mbn /dev/mtd26
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/14883
Signed-off-by: Robert Marko <robimarko@gmail.com>
This adds support for the RTL8723BE PCIe Wi-Fi Adapter by adding backports drivers
Signed-off-by: David Adriao <davidadriao@dglitch.com>
[Do not remove rtl8xxxu and add dependency to rtl8723be-firmware]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This is required for linux-6.1 compatibility.
IRQs are not automatically mapped from HW to virtual IRQ numbers when
the IRQ domain is registered. This happens when the IRQ number is read
from the device tree based on the IRQ domain from the device tree now.
In kernel 5.15 it was done when the IRQ domain was registered.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
This is required for linux-6.1 compatibility.
IRQs are not automatically mapped from HW to virtual IRQ numbers when
the IRQ domain is registered. This happens when the IRQ number is read
from the device tree based on the IRQ domain from the device tree now.
In kernel 5.15 it was done when the IRQ domain was registered.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
This is required for linux-6.1 compatibility.
IRQs are not automatically mapped from HW to virtual IRQ numbers when
the IRQ domain is registered. This happens when the IRQ number is read
from the device tree based on the IRQ domain from the device tree now.
In kernel 5.15 it was done when the IRQ domain was registered.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
This makes the components used on the lantiq SoCs compile with kernel
6.1.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
[also fix ifxmips_ptm_adsl.c]
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
We simply grep for "src/". So no need for "\/".
Furthermore, since grep-3.8 this creates warnings.
As written in the grep-3.8 announcement:
Regular expressions with stray backslashes now cause warnings, as
their unspecified behavior can lead to unexpected results.
For example, '\a' and 'a' are not always equivalent
<https://bugs.gnu.org/39678>.
Fixes a warning during the first boot:
grep: warning: stray \ before /
Signed-off-by: Georgi Valkov <gvalkov@gmail.com>
gpio.h has been deprecated for a while and no longer compiles with 6.6.
Include the proper header.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15471
Signed-off-by: Robert Marko <robimarko@gmail.com>
Currently, trying to compile qca-ssdk on macOS will fail in a weird way:
make[6]: *** No rule to make target 'openwrt/build_dir/target-aarch64_cortex-a53_musl/linux-qualcommax_ipq807x/qca-ssdk-2024.04.17~3d060f7a/-n',
needed by 'openwrt/build_dir/target-aarch64_cortex-a53_musl/linux-qualcommax_ipq807x/qca-ssdk-2024.04.17~3d060f7a/qca-ssdk.o'. Stop.
After looking looking at src_list.dep from which KBuild cmd_mod will
generate the list of objects to compile it looked like:
-n /src/adpt/adpt.c
-n
-n
Which was rather suspicous so after comparing to the same file but with
Fedora as host:
/src/adpt/adpt.c src/adpt/hppe/adpt_hppe_fdb.c src/adpt/hppe/adpt_hppe_mib.c
It was clear that echo -n which was used in SSDK-s target.mk was not
working as intented, and it looked like the POSIX only version of echo
was being used which does not honor -n.
So, after failling to reproduce it externally, replacing the call to echo
with a full path to coreutils echo fixed the compilation.
After further debugging, it was determined that SSDK does not honor
CONFIG_SHELL like other kernel modules so it was defaulting to /bin/sh as
the shell make was calling thus calling the /bin/sh built-in echo which on
macOS is the old Bash 3.2 one and it does not respect -n.
So, we have to explicitly pass SHELL=$(BASH) to SSDK to make it use bash
like kernel build or other kernel modules.
This is not an issue since on macOS we always build bash anyway.
Link: https://github.com/openwrt/openwrt/pull/15459
Signed-off-by: Robert Marko <robimarko@gmail.com>
FCC ID: A8J-EWS660AP
Engenius ENS1750 is an outdoor wireless access point with
2 gigabit ethernet ports, dual-band wireless,
internal antenna plates, and 802.3at PoE+
Engenius EWS660AP, ENS1750, and ENS1200 are "electrically identical,
different model names are for marketing purpose" according to docs
provided by Engenius to the FCC.
**Specification:**
- QCA9558 SOC 2.4 GHz, 3x3
- QCA9880 WLAN mini PCIe card, 5 GHz, 3x3, 26dBm
- AR8035-A PHY RGMII GbE with PoE+ IN
- AR8033 PHY SGMII GbE with PoE+ OUT
- 40 MHz clock
- 16 MB FLASH MX25L12845EMI-10G
- 2x 64 MB RAM
- UART at J1 populated, RX grounded
- 6 internal antenna plates (5 dbi, omni-directional)
- 5 LEDs, 1 button (power, eth0, eth1, 2G, 5G) (reset)
**MAC addresses:**
Base MAC addressed labeled as "MAC"
Only one Vendor MAC address in flash
eth0 *:d4 MAC art 0x0
eth1 *:d5 --- art 0x0 +1
phy1 *:d6 --- art 0x0 +2
phy0 *:d7 --- art 0x0 +3
**Serial Access:**
the RX line on the board for UART is shorted to ground by resistor R176
therefore it must be removed to use the console
but it is not necessary to remove to view boot log
optionally, R175 can be replaced with a solder bridge short
the resistors R175 and R176 are next to the UART RX pin
**Installation:**
2 ways to flash factory.bin from OEM:
Method 1: Firmware upgrade page:
OEM webpage at 192.168.1.1
username and password "admin"
Navigate to "Firmware Upgrade" page from left pane
Click Browse and select the factory.bin image
Upload and verify checksum
Click Continue to confirm and wait 3 minutes
Method 2: Serial to load Failsafe webpage:
After connecting to serial console and rebooting...
Interrupt uboot with any key pressed rapidly
execute `run failsafe_boot` OR `bootm 0x9fd70000`
wait a minute
connect to ethernet and navigate to
"192.168.1.1/index.htm"
Select the factory.bin image and upload
wait about 3 minutes
**Return to OEM:**
If you have a serial cable, see Serial Failsafe instructions
otherwise, uboot-env can be used to make uboot load the failsafe image
ssh into openwrt and run
`fw_setenv rootfs_checksum 0`
reboot, wait 3 minutes
connect to ethernet and navigate to 192.168.1.1/index.htm
select OEM firmware image from Engenius and click upgrade
**TFTP recovery:**
Requires serial console, reset button does nothing
rename initramfs.bin to '0101A8C0.img'
make available on TFTP server at 192.168.1.101
power board, interrupt boot
execute tftpboot and bootm 0x81000000
**Format of OEM firmware image:**
The OEM software of ENS1750 is a heavily modified version
of Openwrt Kamikaze. One of the many modifications
is to the sysupgrade program. Image verification is performed
simply by the successful ungzip and untar of the supplied file
and name check and header verification of the resulting contents.
To form a factory.bin that is accepted by OEM Openwrt build,
the kernel and rootfs must have specific names...
openwrt-ar71xx-generic-ens1750-uImage-lzma.bin
openwrt-ar71xx-generic-ens1750-root.squashfs
and begin with the respective headers (uImage, squashfs).
Then the files must be tarballed and gzipped.
The resulting binary is actually a tar.gz file in disguise.
This can be verified by using binwalk on the OEM firmware images,
ungzipping then untaring.
Newer EnGenius software requires more checks but their script
includes a way to skip them, otherwise the tar must include
a text file with the version and md5sums in a deprecated format.
The OEM upgrade script is at /etc/fwupgrade.sh.
OKLI kernel loader is required because the OEM software
expects the kernel to be no greater than 1536k
and the factory.bin upgrade procedure would otherwise
overwrite part of the kernel when writing rootfs.
Note on PLL-data cells:
The default PLL register values will not work
because of the external AR8035 switch between
the SOC and the ethernet port.
For QCA955x series, the PLL registers for eth0 and eth1
can be see in the DTSI as 0x28 and 0x48 respectively.
Therefore the PLL registers can be read from uboot
for each link speed after attempting tftpboot
or another network action using that link speed
with `md 0x18050028 1` and `md 0x18050048 1`.
The clock delay required for RGMII can be applied
at the PHY side, using the at803x driver `phy-mode`.
Therefore the PLL registers for GMAC0
do not need the bits for delay on the MAC side.
This is possible due to fixes in at803x driver
since Linux 5.1 and 5.3
Tested-by: Kevin Abraham <kevin@westhousefarm.com>
Signed-off-by: Kevin Abraham <kevin@westhousefarm.com>
Linux kernel commit torvalds/linux@b8a1a4cd5a
added a temporary probe_new member to struct i2c_driver, to drop the
rarely used second parameter of the probe function and not break API for
out of tree drivers. With torvalds/linux@5eb1e6e459,
which is part of v6.6, this probe_new member is dropped and the
signature of the probe function is updated.
ubnt-ledbar is used by the mediatek and ramips targets and both have
been updated to v6.6, so adapt the probe function signature and remove
other compat code for versions before v6.6.
Signed-off-by: Sven Wegener <sven.wegener@stealer.net>
Link: https://github.com/openwrt/openwrt/pull/15443
Signed-off-by: Robert Marko <robimarko@gmail.com>
uid/gid range should be limited to 16bit unsigned integer range to
avoid "wraparound" issues with permissions where jffs2
is employed for storage and chown 65536 (first auto-created user)
becomes equivalent to chown 0
Fixes: #13927
Signed-off-by: Thomas Winkler <tewinkler86@gmail.com>
This includes multiple updates for BCM2711 and BCM2712.
Full changelog:
0968de2871...1.20240424
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Newer compilers default to building with C++17 as default, which has the
register keyword removed and thus errors.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
don't mention SHA1 in order to not confuse users - SHA1 support is already disabled (except RSA-SHA1 signagures).
ref: https://github.com/openwrt/openwrt/issues/15281
Signed-off-by: Konstantin Demin <rockdrilla@gmail.com>
- update dropbear to latest stable 2024.85;
for the changes see https://matt.ucc.asn.au/dropbear/CHANGES
- drop cherry-picked patches (merged in release 2024.84)
- refresh remaining patches
Tested-by: Stijn Segers <foss@volatilesystems.org>
Signed-off-by: Konstantin Demin <rockdrilla@gmail.com>
The 'nandbiterrs' tool is useful to find out of bit error correction of
NAND is working as expected by deliberately introducing bit errors and
telling up to which number they can be corrected.
Enable build of the testing tools and package the 'nandbiterrs' tool as
part of the nand-utils package.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
With the switch from the uImage.FIT partition parser to fitblk the
cmdline needs to be adjusted as well. Do this now as it has been
forgotten when the switch was done.
Fixes: 6368ed1ae5 ("mediatek: mt7623: phase out uImage.FIT partition parser")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
99dd990690bc treewide: refactor pref(erred) to preferred_lt (lifetime)
4c2b51eab368 treewide: refactor valid to valid_lt (lifetime)
3b4e06055900 router: inherit user-assigned preferred_lifetime
e164414aa184 router: limit prefix preferred_lt to valid_lt in accordance with RFC4861
a2176af7bdeb treewide: spell-fixes and new comments for extra clarification
4590efd3a2b3 treewide: normalize spaces to tabs
2edc60cb7c7a router: rename minvalid to lowest_found_lifetime
7ee72ee17bfa router: disambiguate and clarify 'no route' messages
a29882318a4c config: set RFC defaults for preferred lifetime
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
There is a new branch 12.5.r2 for kernel 6.6, so refresh
and update patches.
Delete patch 0010-nss-dp-include-net-netdev_rx_queue.h.patch
Changes:
2024-04-04 -5bf8b91 [qca-nss-dp] Adding support for port ID 3 & 4 in MHT switch
2024-03-28 -ce1e4cf [qca-nss-dp] Use skb_queue_head_init instead of __skb_queue_head_init.
2024-03-11 -0d26366 [qca-nss-dp] Read MHT LAN port status for ErP phase2
2024-03-22 -8382f14 [qca-nss-dp] Fix compilation issues seen on ginger branch for Miami profile
2023-05-02 -09b0983 [qca-nss-dp] vp list processing for capwap
2024-02-22 -bc09a01 [qca-nss-dp] EDMA ring reset for PPE-DS
2024-03-12 -2fcb586 [qca-nss-dp] Fix the EDMA clock frequency for the mitigation timer configuration
2024-02-23 -44ba1be [qca-nss-dp] Add API to retrieve ethernet netdevs for ErP
2024-02-09 -a5979b7 [qca-nss-dp] send napi and ip checksum for VP handler
2024-01-12 -1b9cb5d qca-nss-dp: User netdev_alloc_skb_fast instead of dev_alloc_skb
2024-01-08 -a859b48 [qca-nss-dp] NAPI Budget and EDMA Rx size change for KPI improvement.
2024-01-06 -8935523 [qca-nss-dp] Offload L3, L4 checksum to hardware for ppe-vp.
2023-12-07 -bbd9547 [qca-nss-dp] Fix Compilation issues on kernel6.6
2023-10-12 -bc55f75 [qca-nss-dp]: Enable legacy SCS for PPE-VP.
2023-09-08 -6bd771f [qca-nss-dp] Invalidate secondary descriptor before use.
2023-12-19 -b143df8 [qca-nss-dp] Fixed nss_dp_hal_hw_reset functionality for ipq53xx.
2023-12-16 -7cfde1d [qca-nss-dp] Added nss_dp_hal_hw_reset functionality for ipq53xx.
2023-11-02 -70af6c2 [qca-nss-dp] Implement EDMA hang recovery support
2023-11-27 -2202b29 [qca-nss-dp] Add support for adding the link speed for the Miami's port connected to the internal Switch.
2023-12-06 -bef68a8 [qca-nss-dp] Resolve ring utilization reporting issue in EDMA driver
2023-12-06 -eaa7627 [qca-nss-dp] Add/Delete static fdb entries only for physical ports
2023-10-16 -4551d0f [qca-nss-dp]: Support HLOST_TID_override from PPE_VP path.
2023-11-09 -42ad3f3 [qca-nss-dp] Correct the NAPI poll implementation for DS Rx fill handling
2023-10-16 -dfeb7d3 [qca-nss-dp] Check for disabled ethernet port in ErP functions
2023-11-09 -42ad3f3 [qca-nss-dp] Correct the NAPI poll implementation for DS Rx fill handling
2023-10-16 -dfeb7d3 [qca-nss-dp] Check for disabled ethernet port in ErP functions
2023-09-22 -03f83d6 [qca-nss-dp] Correct the mht device flag
2023-08-18 -5efd7f4 [qca-nss-dp] Add EDMA Tx rings for MHT ports
2023-09-11 -7808ba2 [qca-nss-dp] Move DP standby code to new file and use new SSDK API
2023-09-28 -22ade1e [qca-nss-dp] : enable PPE-DS support in 6.x kernel
2023-08-28 -1943922 [qca-nss-dp] Support for bitmap based CPU selection.
2023-08-16 -dcb82a7 qca-nss-dp: 512M profile changes for Miami+Pebble
2023-09-01 -18e51f3 [qca-nss-dp] Fix tx descriptor completion error.
2023-08-28 -0bfde2d [qca-nss-dp] Changes to enable ErP mode
2023-09-05 -f1d635a [qca-nss-dp] Enable fast recycled changes in dp for kernel 6.1
2023-06-15 -55d35bd [qca-nss-dp] Tracking the full utilization of EDMA rings
2023-08-25 -89b9c19 [qca-nss-dp] Restricting the MTU as 9216 for all interfaces in DP
2023-01-03 -5098a4f [qca-nss-dp] Requeue Tx packet in case of Tx-failure.
2023-04-06 -3576dbb [qca-nss-dp] Adding tx napi with four queue per interface.
2023-08-10 -d2b6921 [qca-nss-dp] : changes to support ppe-qdisc for linux 6.x
2023-08-08 -a1941fb [qca-nss-dp] moving SET_NETDEV_DEV for all netdev to set.
2023-07-18 -74d3178 [qca-nss-dp] Reordering the CPU code and ACL index processing.
2023-06-30 -ab03139 [qca-nss-dp] Configure port level PPE offload flag in PPE
2023-06-06 -e9bb8c5 [qca-nss-dp] Rate limit the debug logs.
2023-07-18 -43afb9b [qca-nss-dp] Support Core selection for PPE mirrored packets.
2023-07-11 -92edcfd [qca-nss-dp] Add sysctl to invalidate RX secondary descriptor.
Tested and working on WAX620.
Signed-off-by: Kristian Skramstad <kristian+github@83.no>
Link: https://github.com/openwrt/openwrt/pull/15383
Signed-off-by: Robert Marko <robimarko@gmail.com>
Qualcomm recently committed a new branch (12.5.r2) targeting kernel
6.6. This lets us clean up a few patches particularly the one for
"C22/C45" mdio.
A quick way to see what changed for IPQ807x/6018 was to list the files produced
during build (**/*.o), replace the extension with ".c", and doing a
`git log`.
Filtering from those commits, ones of particular interest are listed
below:
```
2024-04-16 - 0d8f30aa - fix compile issue on hk with linux style build
2024-01-29 - 636464f7 - update the check for port link notify
2024-01-24 - 30c10e7f - enable and disable loopback for xgmac to fix qm stuck issue
2024-01-15 - b6ea10aa - update the the APIs to access switch
2024-01-08 - a1687502 - Disable Tx bridge mac before power off the PHY
2024-01-07 - 3eafb613 - support led configure for malibu phy
2024-01-07 - 5c1af60d - remove phy type check from mac reset when mode switch
2023-12-17 - 79d0b1e8 - remove the PHY access APIs in ssdk_plat.c
2023-12-16 - b2953740 - Update mii read/write functions
2023-12-11 - 37f2eac3 - add port id check for fdb entry
2023-12-11 - d040ca4d - support mdio clause45 on kernel6.6
2023-12-07 - 11494fbc - use barrier mw() during access fdb entry table
2023-12-03 - 8e40a284 - fix build warnings on kernel6.6
2023-11-10 - 10aa0a02 - change speed value when call ssdk_port_link_notify
2023-11-06 - ee4c4a60 - Update mac bitmap value of L3 table on MAC delete
2023-11-03 - 7cd27d39 - support 10G phy common feature
2023-10-30 - 383cc0d2 - fix mactype and mux select issue
2023-10-24 - decf534a - support autoneg status query on force port
2023-10-11 - 111d574e - move ssdk_led_init to regi_init
2023-10-08 - 6b14c142 - the combo port also need to parse SFP pins
2023-10-03 - fb2e0401 - fix port5 interface mode switch issue in erp case
```
Verified with users on QNAP 301W, NBG7815, and myself on Dynalink
DL-WRX36 that everything is functional, including LEDS.
Signed-off-by: Sean Khan <datapronix@protonmail.com>
Link: https://github.com/openwrt/openwrt/pull/15379
Signed-off-by: Robert Marko <robimarko@gmail.com>
Enable building multiple test programs and related kernel modules, with
initial support for the bpf_testmod.ko module required since kernel 6.4.
Explicitly disable LTO and clean up makefile variables and formatting.
Fix a musl-related build failure by adding a kernel 6.6 patch:
360-selftests-bpf-portability-of-unprivileged-tests.patch
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
This has been tested on two of my Unifi 6 LR v2s:
```bash
$ fw_printenv # before
Cannot parse config file '/etc/fw_env.config': No such file or directory
$ cat /etc/fw_env.config
/dev/mtd3 0x0000 0x1000 0x1000 1
$ fw_printenv
arch=arm
baudrate=115200
board=mt7622_evb
board_name=mt7622_evb
bootcmd=bootubnt
bootdelay=3
bootfile=uImage
cpu=armv7
device_model=U6-LR
ethact=mtk_eth
ethaddr=<redacted>
ethcard=AQR112C
ipaddr=<redacted>
is_default=true
loadaddr=0x5007FF28
macaddr=<redacted>
serverip=<redacted>
soc=mt7622
stderr=serial
stdin=serial
stdout=serial
vendor=mediatek
is_ble_stp=true
```
I had to reverse-engineer the working settings above to the UCI script.
Signed-off-by: Joel Low <joel@joelsplace.sg>
Link: https://github.com/openwrt/openwrt/pull/13897
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The DropBear's dropbearkey supports limited set of arguments of
OpenSSH ssh-keygen: -t, -q -N -Y
After the change you can generate a key with the same command.
Still many features of the original OpenSSH ssh-keygen are absent in
the dropbearkey.
If it's needed then users should install openssh-keygen package that
will replace the /usr/bin/ssh-keygen with the full version.
Signed-off-by: Sergey Ponomarev <stokito@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/14174
[ wrap commit description to 80 columns ]
Link: https://github.com/openwrt/openwrt/pull/14174
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This adds support for the bpi-r4 variant with internal 2.5G PHY and
additional ethernet port instead of second sfp.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
This adds support for the bpi-r4 variant with internal 2.5G PHY and
additional ethernet port instead of second sfp.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Hardware:
=========
SOC: Qualcomm IPQ4019
WiFi 1: QCA4019 IEEE 802.11b/g/n
WiFi 2: QCA4019 IEEE 802.11a/n/ac
WiFi 3: QCA9886 IEEE 802.11a/n/ac
Bluetooth: Qualcomm CSR8510 (A10)
Zigbee: Silicon Labs EM3581 NCP + Skyworks SE2432L
Ethernet: Qualcomm Atheros QCA8072 (2-port)
Flash: Samsung KLM4G1FEPD (4GB eMMC)
RAM (NAND): 512MB
LED Controller: NXP PCA9633 (I2C)
Buttons: Single reset button (GPIO).
Ethernet:
=========
The device has 2 ethernet ports, configured as follows by default:
- left port: WAN
- right port: LAN
Wifi:
=====
The Wifi radios are turned off by default. To configure the router,
you will need to connect your computer to the LAN port of the device.
Bluetooth and Zigbee:
=====================
Configuration included but not tested.
Storage:
========
For compatibility with stock firmware, all of OpenWrt runs in a 136 MiB
eMMC partition (of which there are two copies, see below). You can also
use partition /dev/mmcblk0p19 "syscfg" (3.4 GiB) any way you see fit.
During very limited tests, stock firmware did not mount this partition.
However, backing up its stock content before use is recommended anyway.
Firmware:
=========
The device uses a dual firmware mechanism: it automatically reverts to
the previous firmware after 3 failed boot attempts.
You can switch to the inactive firmware copy by changing the "boot_part"
U-Boot environment variable. You can also do it by turning on the device
for a couple of seconds and then back off, 3 times in a row.
Installation:
=============
OpenWrt's "factory" image can be installed via the stock web UI:
1. Login to the UI. (The default password is printed on the label.)
2. Enter support mode by clicking on the "CA" link at the bottom.
3. Click "Connectivity", "Choose file", "Start", and ignore warnings.
This port is based on work done by flipy (https://github.com/flipy).
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15345
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add "linux64-loongarch64-openwrt" into openssl configurations to enable
building on loongarch64 machines.
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
* Allow kmod-acpi-video to be built for loongarch64:
The x86-specific CONFIG_ACPI_WMI will be split from default
kmod-acpi-video as a board-specific addition.
* Allow kmod-drm-amdgpu to be built for loongarch64:
Also add loongarch64-specific configs and modules.
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
To enable verbose log for xdp-tools compilation, we check for "c" in
the OPENWRT_VERBOSE, but verbose.mk supports only "w" and "s" for V=1
and V=99.
Fix the wrong matching and correctly enable verbose output matching for
"s".
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Upgrade the OpenSBI firmware used by RISC-V CPUs to 1.4.
Runtime-tested:
- d1 (Lichee RV)
- sifiveu (SiFive Unleashed)
Updates since last release:
1.4:
Synopsys DesignWare APB GPIO driver
Zicntr and Zihpm support
Console print improvements
Smepmp support
Simple FDT based syscon regmap driver
Syscon based reboot and poweroff driver
Non-contiguous hpm counters
Smcntrpmf support
Full sparse hartid support
IPI improvements
RFENCE improvements
Zkr support
Andes custom PMU support
1.3.1:
ACLINT driver fix for disabled CPUs
SBI PMU fix for out-of-bound access
Designware GPIO driver
1.3:
Allow platform to influence cold boot HART selection
Starfive JH7110 platform support
Split RX and RW firmware regions
Advertise non-retentive suspend for allwinner D1 platform
Byteorder/endianness conversion macros
SBI debug console extension (Experimental)
Configure the PMA regions for RZ/Five platform
SBI system suspend extension (Experimental)
SBI PMU platform firmware events (Experimental)
SBI CPPC extension (Experimental)
Optimized remote TLB flushes
Simple heap for boot time memory allocations
Bring back no-map DT property for reserved memory nodes
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
This is needed to boot the BCM6238-based Inteno XG6846.
Currently this is restricted to the XG6846 board.
Reviewed-by: Paul Donald <newtwen+github@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currently it's needed to have gcc-multilib on the host to correctly
compile xdp-tools. This is wrong and means that we are using host header
to compile a tool.
By some searching in how the makefile works it was discovered that
BPF_CFLAGS were not used and required to be appended to config.mk
Only one single header was added but we should include each BPF_CFLAGS
from bpf.mk. To make this some patching to bpf-header were required and
some patches to xdp-tools were required.
Also it's needed to pass the correct target to BPF_CFLAGS.
With the following changes xdp-tools can correctly compile with each
header from bpf-headers and should not use any host header.
Co-Developed-by: Andre Heider <a.heider@gmail.com>
Signed-off-by: Andre Heider <a.heider@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/11825
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
netlink.h header have NL_SET_ERR_MSG_MOD that is tied to kmods. We don't
need kmods on bpf tools and this cause compilation error if the header
is included. Fix it by dropping NL_SET_ERR_MSG_MOD.
Link: https://github.com/openwrt/openwrt/pull/11825
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
mDNS broadcast can't accept empty TXT record and would fail
registration.
Current procd_add_mdns_service checks only if the first passed arg is
empty but don't make any verification on the other args permittins
insertion of empty values in TXT record.
Example:
procd_add_mdns "blah" \
"tcp" "50" \
"1" \
"" \
"3"
Produce:
{ "blah_50": { "service": "_blah._tcp.local", "port": 50, "txt": [ "1", "", "3" ] } }
The middle empty TXT record should never be included as it's empty.
This can happen with scripts that make fragile parsing and include
variables even if they are empty.
Prevent this and make the TXT record more solid by checking every
provided TXT record and include only the non-empty ones.
The fixed JSON is the following:
{ "blah_50": { "service": "_blah._tcp.local", "port": 50, "txt": [ "1", "3" ] } }
Fixes: b0d9dcf84d ("procd: update to latest git HEAD")
Reported-by: Paul Donald <newtwen@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15331
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Well, it seems that cryptopp hash was never refreshed since calling
make package/boot/arm-trusted-firmware-mvebu/check FIXUP=1 V=s does not
actually refresh the download calls hashes so refresh it manually.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Since ("download: don't overwrite VERSION variable") trying to download the
required sources for mvebu ATF will fail with:
Makefile:247: *** Download/mox-boot-builder is missing the SOURCE_VERSION field.. Stop.
This also broke the buildbot mvebu/cortex-a53 builds.
So, fix it by switching to SOURCE_VERSION instead.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
APK (Alpine Package Keeper) is the package manager of Alpine Linux and
has multiple advantages over OPKG. While Alpine uses APK version 2, this
commit adds version 3 with a heavily optimised database structure and
additional feature making it suitable for OpenWrt.
This commit will be followed by many more to add APK build capabilities
to the OpenWrt build system, firstly enabling side by side builds of APK
and OPKG packages, later replacing OPKG entirely.
Signed-off-by: Paul Spooren <mail@aparcar.org>
These options are not available in mbedtls 3.6.0 and selecting them
causes an error.
MBEDTLS_CERTS_C was removed in:
1aec64642c
MBEDTLS_XTEA_C was removed in:
10e8cf5fef
MBEDTLS_SSL_TRUNCATED_HMAC was removed in:
4a7010d1aa
Fixes: 0e06642643 ("mbedtls: Update to version 3.6.0")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Changes:
- new URL for sources (old address is dead)
- daemon and utils from packages feed are merged in here
- only build once
- no need to update at the same time in both places
- update to v3.1.4
- removed unneeded patches
- added audisp-syslog
- removed audispd (no longer exists)
- rename and move to package/utils/audit
- update new path in one dependent package
Signed-off-by: Marius Dinu <m95d+git@psihoexpert.ro>
With "ebfe8b4 CMakeLists: set no-dangling-pointer" the compilation
option is set in uqmi, and can therefore be removed from no-error.
Signed-off-by: Jean Thomas <jean.thomas@wifirst.fr>
e7207be uqmi: print radio interfaces in serving system command
6ef41d6 uqmi: create function to print radio interface string
e25d042 uqmi: Add basic 5G NR support
3e782be uqmi: sync data from libqmi project
368d46c uqmi: support C reserved keywords in upstream JSON files
02e42c0 reorganize source code in common and uqmi specific parts
4591f0a .gitignore build/ directories
2b57ee1 uqmi: commands-uim: fix uninitialized use of card_application_state
7c77e77 data/code-gen: add support for indications
ddbf864 qmi-struct.h: add missing includes
5320c1d move qmi_get_error_str to into utils.c
1503bc7 dev.c: add missing import strings.h
bae945f commands-nas: add missing includes
9ffd0e2 commands: make `struct blob_buf status` public
a4fbdcc commands-nas: fix gcc warning
8ff632a dev.c: add comment to qmi_request_wait()
a043a74 CMakeLists: refactor SOURCES variable to allow later adding uqmid
ebfe8b4 CMakeLists: set no-dangling-pointer
c47125d CMakeLists: improve generated files
0f64b69 CMakeLists: update cmake minimum version to 3.5
As the built uqmi binary is now moved to a dedicated directory,
update the Makefile accordingly.
Signed-off-by: Jean Thomas <jean.thomas@wifirst.fr>
This adds support for mbedtls 3.6.0.
The 3.6 version is the next LTS version of mbedtls.
This version supports TLS 1.3.
This switches to download using git. The codeload tar file misses some
git submodules.
Add some extra options added in mbedtls 3.6.0.
The size of the compressed ipkg increases:
230933 bin/packages/mips_24kc/base/libmbedtls13_2.28.7-r2_mips_24kc.ipk
300154 bin/packages/mips_24kc/base/libmbedtls14_3.6.0-r1_mips_24kc.ipk
The removed patch was integrated upstream.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
It seems that somehow a wrong hash has been used for ipq-wifi, so refresh
it.
Fixes: f10d55df9e ("ipq-wifi: update to Git HEAD (2024-04-26)")
Signed-off-by: Robert Marko <robimarko@gmail.com>
Because these capability advertisements default to on in lldpd, they
became absent at reload, and not restart, due to how the reload logic
works ( keep daemon running, send unconfigured and then the new config
via socket ), and it was not evident unless you happened to be looking
for it (e.g. via pcap or tcpdump). It was also not evident from the
manpage ( have now sent patches upstream ).
At reload time, the unconfigure logic disabled them unless they were
explicitly enabled (compare with other settings where 'unconfigure' just
resets them). Now they default to on/enabled at init time, and are
explicitly 'unconfigure'd at startup if the user disables them via:
lldp_mgmt_addr_advertisements=0
lldp_capability_advertisements=0
In other words: explicit is necessary to disable the advertisements.
The same applies to 'configure system capabilities enabled'. Technically
'unconfigure'd is the default but now it is explicit at reload.
Tested on: 23.05.3
Signed-off-by: Paul Donald <newtwen+github@gmail.com>
Building perf's intel-pt-decoder fails on both PPC32 and PPC64:
/home/stijn/Development/OpenWrt/openwrt/staging_dir/toolchain-powerpc64_e5500_gcc-13.2.0_musl/lib/gcc/powerpc64-openwrt-linux-musl/13.2.0/../../../../powerpc64-openwrt-linux-musl/bin/ld.bfd:
/home/stijn/Development/OpenWrt/openwrt/build_dir/target-powerpc64_e5500_musl/linux-qoriq_generic/linux-6.1.86/tools/
perf-target-powerpc64_e5500_musl/perf-in.o: in function `insn_set_byte':
/home/stijn/Development/OpenWrt/openwrt/build_dir/target-powerpc64_e5500_musl/linux-qoriq_generic/linux-6.1.86/tools/perf/util/intel-pt-decoder/../../../arch/x86/include/asm/insn.h:64:
undefined reference to `__le32_to_cpu'
Add NO_AUXTRACE=1 to MAKE_FLAGS for LINUX_KARCH powerpc, which disables
build of intel-pt-decoder on both PPC32 and PPC64.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
fab9e29f6b92 ipq6018: update regdb in TPLink EAP610-Outdoor BDF
6d02b65fadf3 ipq8074: update RegDB in new submitted BDF
644ba9ea2e66 ipq6018: update RegDB in new submitted BDF
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
uboot-envtools is currently missing config for Edgerouter-X
and its not immediately obvious what settings to manually
apply.
Provide default configuration for envtools on Edgerouter-X.
Signed-off-by: Tim Lunn <tim@feathertop.org>
This adds a kernel module package for the Marvell
MV88E6XXX DSA switch and a separate module package for
the DSA tagger since it can in theory be used by multiple
DSA switches. Enable both DSA and EDSA tags in the
tagger.
We can't just compile this in because just a few devices
has this DSA, and it depends on e.g. the I2C and SFP
to be loaded as modules first.
We have no examples of DSA switches being packaged as
modules before, all seem to be compiled in, but it
actually works just fine to do this.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This fixes multiple security problems:
* [High] CVE-2024-0901 Potential denial of service and out of bounds
read. Affects TLS 1.3 on the server side when accepting a connection
from a malicious TLS 1.3 client. If using TLS 1.3 on the server side
it is recommended to update the version of wolfSSL used.
* [Med] CVE-2024-1545 Fault Injection vulnerability in
RsaPrivateDecryption function that potentially allows an attacker
that has access to the same system with a victims process to perform
a Rowhammer fault injection. Thanks to Junkai Liang, Zhi Zhang, Xin
Zhang, Qingni Shen for the report (Peking University, The University
of Western Australia)."
* [Med] Fault injection attack with EdDSA signature operations. This
affects ed25519 sign operations where the system could be susceptible
to Rowhammer attacks. Thanks to Junkai Liang, Zhi Zhang, Xin Zhang,
Qingni Shen for the report (Peking University, The University of
Western Australia).
Size increased a little:
wolfssl 5.6.6:
516880 bin/packages/mips_24kc/base/libwolfssl5.6.6.e624513f_5.6.6-stable-r1_mips_24kc.ipk
wolfssl: 5.7.0:
519429 bin/packages/mips_24kc/base/libwolfssl5.7.0.e624513f_5.7.0-stable-r1_mips_24kc.ipk
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This contains a fix for:
CVE-2024-28960: An issue was discovered in Mbed TLS 2.18.0 through 2.28.x
before 2.28.8 and 3.x before 3.6.0, and Mbed Crypto. The PSA Crypto
API mishandles shared memory.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The Upstream Linux community has discontinued support for the target.
Maintaining support for it downstream would require too much effort.
Moreover, it seems that the supported hardware is no longer deemed worthy
of it.
Signed-off-by: Nick Hainke <vincent@systemli.org>
Add new functions for ath11k caldata:
- ath11k_patch_mac (from 0 to 5)
- ath11k_remove_regdomain
- ath11k_set_macflag (some pre-caldata have the nvMacFlag flag unset which is needed to change the MAC address)
Additionaly for ath10k caldata:
- ath10k_remove_regdomain
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
This update contains a minor fix to resolve "detected write beyond size
of field" warning during compilation:
* "replace [0] with []" (1d0d08c)
All patches still apply.
References:
* https://github.com/openwrt/openwrt/issues/15108
Signed-off-by: Stefan Kalscheuer <stefan@stklcode.de>
Spectrum SAX1V1K is a AX WIFI router with 3 1G and 1 2.5G ports.
The router is provided to Spectrum customers.
It is OEM of Askey RT5010W
https://forum.openwrt.org/t/spectrum-sax1v1k-askey-rt5010w-openwrt-support/149923
It continues the original work by @MeisterLone to get this device supported.
Specifications:
```
• CPU: Qualcomm IPQ8072A Quad core Cortex-A53 2.2GHz
• RAM: 2048MB of DDR3
• Storage: 1024MB eMMC
• Ethernet: 3x 1G RJ45 ports (QCA8075) + 1 2.5G Port (QCA8081)
• WLAN:
• 2.4GHz: Qualcomm QCN5024 4x4 802.11b/g/n/ax 1174 Mbps PHY rate
• 5GHz: Qualcomm QCN5054 4x4 802.11a/b/g/n/ac/ax 2402 PHY rate
• LED: 1 gpio-controlled dual color led (blue/red)
• Buttons: 1x reset
• Power: 12V DC jack
```
Notes:
```
• This commit adds only single partition support, that means
sysupgrade is upgrading the current rootfs partition.
• Installation can be done by serial connection only.
• A poulated serial header is onboard
https://forum.openwrt.org/t/spectrum-sax1v1k-askey-rt5010w-openwrt-support/149923/6
• RX/TX is working, u-boot bootwait is active, secure boot is enabled.
```
Installation Instructions:
**Most part of the installation is performed from an initramfs image.**
Boot initramfs : Using serial connection
1. Boot up the device and wait till it displays "VERIFY_IB: Success. verify IB ok"
2. Once that message appears,
login with username 'root'
password serial number of your router in uppercase.
3. Use vi to paste the 'open.sh' script from @MeisterLone github on your device
https://github.com/MeisterLone/Askey-RT5010W-D187-REV6/blob/master/Patch/open.sh
4. chmod 755 open.sh
5. ./open.sh
6. Set your ip to 192.168.0.1
7. Run a TFTP server and host the initramfs image on the TFTP server and name it "recovery.img"
8. Reboot device. On boot it will try TFTP.
Install OpenWrt from initramfs image:
1. Use SCP (or other way) to transfer OpenWrt factory image
2. Connect to device using SSH (on a LAN port)
3. Flash firmware: sysupgrade
# sysupgrade -n -v /tmp/openwrt_sysupgrade.bin
4. Set U-boot env variable: bootcmd
# fw_setenv bootcmd "run fix_uboot; run setup_and_boot"
5. Reboot the device
# reboot
6. Once device is booted, residue of previous firmware will prevent openwrt to work properly.
Factory Reset is MUST required
# Once serial console is displaying to login, hold reset button for 10 sec
7. Now everything should be operational.
Note: this PR adds only single partition support, that means sysupgrade is
upgrading the current rootfs partition
Signed-off-by: Connor Yoon <j_connor@taliaent.com>
ec8c620fd5f4 split bridge-local disable into rx and tx
40b1c5b6be4e flow: do not attempt to offload bridge-local flows
Signed-off-by: Felix Fietkau <nbd@nbd.name>
For interface type parameters, the man page documents patterns:
```
*,!eth*,!!eth1
uses all interfaces, except interfaces starting with "eth",
but including "eth1".
```
* Renamed `_ifname` to `_l2dev`.
* get the l2dev via network_get_physdev (and not l3dev)
* Glob pattern `*` is also valid - use noglob for this
The net result is that now interface 'names' including globs '*' and '!'
inversions are included in the generated lldpd configs.
Temporarily `set -o noglob` and then `set +o noglob` to disable & enable
globbing respectively, because when we pass `*` as an interface choice,
other file and pathnames get sucked in from where the init script runs,
and the `*` never makes it to lldpd.
Tested extensively on: 22.03.6, 23.05.3
Signed-off-by: Paul Donald <newtwen+github@gmail.com>
[ squash with commit bumping release version ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Lets update to 2024.04 in order to drop all of the patches as they have
been merged upstream.
Tested on Methode eDPU.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
f9a28a9ce864 ustream-ssl: poll connection on incomplete reads
3c49e70c4622 ustream-ssl: increase number of read buffers
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Reduce calls and pipes and read from urandom once directly with hexdump
for the necessary 5 bytes of random data to build the 48 bit ULA Prefix.
Fewer calls and forks; finish quicker; less memory used.
Tested on: 23.05.3
Signed-off-by: Paul Donald <newtwen+github@gmail.com>
It seems that move to kernel 6.6 somehow fixed the remoteproc restart so
now it properly restarts and thus coldboot calibration works as well.
ipq60xx still seems to be broken in a different way so keep it disabled.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add patch fixing rmmod and insmod. Lots of flawed logic fixed that
permits the module to correctly rmmod and insmod later.
Just to quote some change, use phy_detach instead of phy_disconnect, fix
exclusive reset_control that could only be used once, fix kernel panic
on second edma_cleanup, stop traffic before module exit...
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This reverts commit a9e22ffa50.
After doing a clean rebuild, it turns out that this change is not necessary
Signed-off-by: Felix Fietkau <nbd@nbd.name>
3159bbe0a2eb improve isolation when selecting a fixed output port
c77a7a1ff74d nl: fix getting flow offload stats
a08e51e679dd add support for disabling bridge-local flows via config
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The new script uses a different strategy compared to the previous one.
Instead of trying to split flows by hash and spread them to all CPUs,
use RPS to redirect packets to a single core only.
Try to spread NAPI thread and RPS target CPUs across available CPUs
and try to ensure that the NAPI thread is on a different CPU than the
RPS target. This significantly reduces cycles wasted on the scheduler.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Limiting allowed channels per device may be required and is commonly
supported on other drivers, so include a pending patch to add support for
the same.
Signed-off-by: Robert Marko <robimarko@gmail.com>
As commit 3ce1e4c3d3 ("d1: define subtarget specifically") added the
'generic' subtarget, without 'BUILD_SUBTARGET' the correspond U-Boot
package will be no longer selected automatically.
Fixes: 3ce1e4c3d3 ("d1: define subtarget specifically")
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Update to the latest upstream release to include recent improvements and
bugfixes. Update copyright, fix typo in PKG_NAME, and remove unneeded use
of MAKE_VARS definition in Makefile. Drop 001-cflags.patch and simplify
002-includes.patch after refreshing. Also simplify LTO/DCE build flags.
Link: https://github.com/libbpf/bpftool/releases/tag/v7.4.0
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Update to the latest upstream release to include recent improvements and
bugfixes, and update copyright. Remove MAKE_VARS usage in Makefile and drop
001-cflags.patch which are no longer needed. Also add flags to disable LTO,
mistakenly dropped earlier.
Link: https://github.com/libbpf/libbpf/releases/tag/v1.4.0
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
only available from >= 1.0.15
Comments are useful. Apparently this config parameter was committed when
openwrt used an older version of lldpd which did not yet support it.
Signed-off-by: Paul Donald <newtwen+github@gmail.com>
Starting with Linux 6.3 the .probe call no longer got the id parameter,
see also commit torvalds/linux@03c835f498
("i2c: Switch .probe() to not take an id parameter").
As the parameter is anyway unused by the driver, drop it when
building the GCA230718 LED driver for newer kernels.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
HW specifications:
* Mediatek MT7981A
* 256MB SPI-NAND
* 512MB DRAM
* Uplink: 1 x 10/100/1000Base-T Ethernet, Auto MDIX, RJ-45 with 802.3at
PoE (Built-in GBe PHY)
* LAN: 1 x 10/100/1000Base-T Ethernet, Auto MDIX, RJ-45 (Airoha EN8801SC)
* 1 Tricolor LED
* Reset button
* 12V/2.0A DC input
Installation:
Board comes with OpenWifi/TIP which is OpenWrt based, so sysupgrade can
be used directly over SSH.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
This module supports the Microchip Technology Inc (SMSC)
EMC2301/EMC2302/EMC2303/EMC2305 fan speed PWM controller chips.
Signed-off-by: Oleg S <remittor@gmail.com>
Historically it's possible to leave the `SUBTARGETS` undefined and
automatically fallback to a "generic" subtarget. This however breaks
various downstream scripts which may have expectations around filenames:
While some targets with an explicit generic subtarget contain `generic`
in the filenames of artifacts, implicit "subtargets" don't.
Right now this breaks the CI[1], possibly also scripts using the ImageBuilders.
This commit removes all code that support implicit handling of
subtargets and instead requires every target to define "SUBTARGETS".
[1]: https://github.com/openwrt/openwrt/actions/runs/8592821105/job/23548273630
Signed-off-by: Paul Spooren <mail@aparcar.org>
e209a4ced1d8 add strdupa macro for compatibility
af1962b9a609 uclient: add helper function for getting ustream-ssl context/ops
488f1d52cfd2 http: add helper function for checking redirect status
b6e5548a3ecc uclient: defer read notifications to uloop timer
352fb3eeb408 http: call ustream_poll if not enough read data is available
e611e6d0ff0b add ucode binding
ddb18d265757 uclient: add function for getting the amount of pending read/write data
980220ad1762 ucode: fix a few ucode binding issues
6c16331e4bf5 ucode: add support for using a prototype for cb, pass it to callbacks
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This is mostly a cosmetic cleanup. The absence of
the return statement was not causing any problems.
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
So, when updating the hash for at91bootstrap it was done via CHECK_ALL=1
so that updated the PKG_MIRROR_HASH for the main v4 version hash, but
at91bootstrap checkout version depends on the subtarget as well.
Choosing to build for sam9x will change the at91bootstrap version to v3
and this hash was not refreshed thus causing the CI to fail.
Fixes: 6918c637b7 ("treewide: package: update missed hashes after switch to ZSTD")
Signed-off-by: Robert Marko <robimarko@gmail.com>
With the switch to ZSTD for git clone packaging, hashes have changed so
fixup remaining package hashes that were missed in the inital update.
Fixes: b3c1c57 ("treewide: update PKG_MIRROR_HASH to zst")
Signed-off-by: Robert Marko <robimarko@gmail.com>
When using zst instead of xz, the hash changes.
This was missed in the initial treewide updated.
Fixes: b3c1c57a35 ("treewide: update PKG_MIRROR_HASH to zst")
Signed-off-by: Robert Marko <robimarko@gmail.com>
When an IBBS interface is configured for IBSS legacy mode, wdev.htmode
is empty. This is empty string results in an empty positional argument
to the "ibbs join" command, for example:
iw dev phy0-ibss0 ibss join crymesh 2412 '' fixed-freq beacon-interval 100
This empty argument is interpreted as an invalid HT mode by 'iw',
causing the entire command to fail and print a "usage" message:
daemon.notice netifd: radio0 (4527): Usage: iw [options] \
dev <devname> ibss join <SSID> <freq in MHz> ...
Although nobody will ever need more than 640K of IBSS, explicitly use
"NOHT" if an HT mode is not given. This fixes the problem.
Fixes: e56c5f7b27 ("hostapd: add ucode support, use ucode for the main ubus object")
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name> [extend to cover more cases]
When using zst instead of xz, the hash changes. This commit fixes the
hash for packages and tools in core.
Signed-off-by: Paul Spooren <mail@aparcar.org>
On Fedora 40 system, some compile error happens when
building iconv-ostream.c. Linking to libiconv-full
fixes this.
Signed-off-by: Yanase Yuki <dev@zpc.st>
hostapd packages were accidentally left out. Clean up this mess by
changing the dependencies to hostapd-common
Signed-off-by: Felix Fietkau <nbd@nbd.name>
With the default BUILD_BOT configuration on a linux 6.6 kernel,
the WNDR4700's kernel no longer fits into the alloted ~3.5MiB,
even with LZMA compression.
Bigger kernels are possible, but there's a problem with Netgear's
"bootcmd":
> if loadn_dniimg 0 0x180000 0x4e0000 && chk_dniimg 0x4e0000; then nand read 0x800000 0x180000 0x20000;bootm 0x500000 - 0x800040;else fw_recovery; fi"
This loads the dni-image starting offset 0x180000 from the NAND
flash (which is the DTB partition) to 0x4e0000 in the RAM. It then
checks whenever the provided image is "valid". If it is then it
reads the DTB again to 0x800000 in the RAM and starts the extraction
and boot process. (If the image wasn't valid then it starts the
automated firmware recovery).
The issues here are that first: the kernel image gets "squeezed"
between 0x500040 and 0x7fffff... And second, the decompressor
only has area 0x0 - 0x500000 for decompression.
Hence the image now requires to update the bootcmd by providing
new values (which have been successfully tested with the original
Netgear WNDR4700 v1.0.0.56 firmware) for the RAM locations and
make full use of the fact that loadn_dniimg loads the DTB as well.
This needs to be done only once. Just connect a serial adapter to
interface with uboot and overwrite (and save) the new bootcmd.
WARNING: The serial port needs a TTL/RS-232 3.3v level converter!
Steps:
0. Power-off the WNDR4700
1. Connect the serial interface (you need to open the WNDR4700)
2. Power-up the WNDR4700
3. Monitor the boot-sequence and hit "Enter"-key when it says:
"Hit any key to stop autoboot" (Be quick, you have a ~2 second window)
4. in the Prompt enter the following commands (copy & paste)
setenv bootcmd "if loadn_dniimg 0 0x180000 0xce0000 && chk_dniimg 0xce0000; then bootm 0xd00000 - 0xce0040;else fw_recovery; fi"
saveenv
run bootcmd
Note: This new bootcmd will also unbrick devices that were bricked
by the bigger 4.19-6.1 kernels.
Note2: This method was tested with a WNDR4700. A big kernel with most
debug features enabled on v6.6.22 measured 4.30 MiB when compressed
with lzma. The uncompressed kernel is 12.34 MiB. This is over the 3 MiB,
the device reserves for the kernel... But it booted! For bigger kernels,
the device needs repartitioning of the the ubi partition due to the
kernel+dtb not fitting into the partition.
Note3: For initramfs development. I would advice to load the initramfs
images to 0x800000 (or higher). i.e.: tftp 800000 wndr4700.bin
Note4: the fw_recovery uboot command to transfer the factory image to
the flash still works.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The PKG_MIRROR_HASH was wrong (again), likely due to an old set of tools
which did not contain the downgrade of xz.
Ref 2070049 unetd: fix PKG_MIRROR_HASH
Fix 89c594e libubox: update to Git HEAD (2024-03-29)"
Signed-off-by: Paul Spooren <mail@aparcar.org>
Fix compilation warning enum-int-mismatch which results in failure to
build kmod-ltq-vmmc in case CONFIG_KERNEL_WERROR is set.
.../build_dir/target-mips_24kc_musl/linux-lantiq_xrx200/drv_vmmc-1.9.0/src/mps/drv_mps_vmmc_common.c:392:14: error: conflicting types for 'ifx_mps_fastbuf_init' due to enum/integer mismatch; have 'IFX_return_t(void)' [-Werror=enum-int-mismatch]
392 | IFX_return_t ifx_mps_fastbuf_init (IFX_void_t)
| ^~~~~~~~~~~~~~~~~~~~
.../build_dir/target-mips_24kc_musl/linux-lantiq_xrx200/drv_vmmc-1.9.0/src/mps/drv_mps_vmmc_common.c:120:13: note: previous declaration of 'ifx_mps_fastbuf_init' with type 'IFX_int32_t(void)' {aka 'int(void)'}
120 | IFX_int32_t ifx_mps_fastbuf_init (IFX_void_t);
| ^~~~~~~~~~~~~~~~~~~~
.../build_dir/target-mips_24kc_musl/linux-lantiq_xrx200/drv_vmmc-1.9.0/src/mps/drv_mps_vmmc_common.c:420:14: error: conflicting types for 'ifx_mps_fastbuf_close' due to enum/integer mismatch; have 'IFX_return_t(void)' [-Werror=enum-int-mismatch]
420 | IFX_return_t ifx_mps_fastbuf_close (IFX_void_t)
| ^~~~~~~~~~~~~~~~~~~~~
.../build_dir/target-mips_24kc_musl/linux-lantiq_xrx200/drv_vmmc-1.9.0/src/mps/drv_mps_vmmc_common.c:121:13: note: previous declaration of 'ifx_mps_fastbuf_close' with type 'IFX_int32_t(void)' {aka 'int(void)'}
121 | IFX_int32_t ifx_mps_fastbuf_close (IFX_void_t);
| ^~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
Refresh patches and bump PKG_RELEASE while at it.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
- move build/ifdef related changes together to the 200 patch range
- reduce adding/removing include statements across patches
- move patches away from the 99x patch range to simplify maintenance
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This adds From:, Date: and Subject: to patches, allowing one to run 'git
am' to import the patches to a hostapd git repository.
From: and Date: fields were taken from the OpenWrt commit where the
patches were first introduced.
Most of the Subject: also followed suit, except for:
- 300-noscan.patch: Took the description from the LuCI web interface
- 350-nl80211_del_beacon_bss.patch: Used the file name
The order of the files in the patch was changed to match what git
format-patch does.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Patch 050-build_fix.patch fixes the abscence of sha384-kdf.o from the
list of needed objetct files when FILS is selected without any other
option that will select the .o file.
While it is a bug waiting to be fixes upstream, it is not needed for
OpenWrt use case, because OWE already selects sha384-kdf.o, and FILS is
selected along with OWE.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
This brings many changes, including fixes for a couple of memory leaks,
and improved interoperability with 802.11r. There are also many changes
related to 802.11be, which is not enabled at this time.
Fixed upstream:
- 022-hostapd-fix-use-of-uninitialized-stack-variables.patch
- 180-driver_nl80211-fix-setting-QoS-map-on-secondary-BSSs.patch
- 993-2023-10-28-ACS-Fix-typo-in-bw_40-frequency-array.patch
Switch PKG_SOURCE_URL to https, since http is not currently working.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Tested-by: Ilya Katsnelson <me@0upti.me>
Tested by: Andrew Sim <andrewsimz@gmail.com>
a2fce001819e CI: add build test run
12bda4bdb197 CI: add CodeQL workflow tests
eb9bcb64185a ustream: prevent recursive calls to the read callback
Signed-off-by: Felix Fietkau <nbd@nbd.name>
It seems that somehow a wrong hash has slipped past PR CI again.
Fixes: 9ef4f7f919 ("qualcommax: ipq60xx: add yuncore fap650 support")
Signed-off-by: Robert Marko <robimarko@gmail.com>
Include the CONFIG_KVM_SMM option in the kvm-x86 package to enable system management mode emulation on KVM.
Co-authored-by: Stefan Hellermann <stefan@the2masters.de>
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Fix error: Package kmod-lan743x is missing dependencies for the following libraries:
fixed_phy.ko
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Kernel 6.2 folded virqfd (eventd interface for VFIO interrupts)
into the base vfio module, it is no longer a tristate option.
Change suggested by vincejv on GitHub:
https://github.com/openwrt/openwrt/pull/14868#issuecomment-1998260124
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Instead of redefining the version schema in cryptodev, use the one
automatically defined via `kernel.mk`.
Specifically this changes the version from <kernel>+<package> to
<kernel>.<package> and thereby making it compatible with APK.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Our CI on GitHub as well as my local machine generates a different
PKG_MIRROR_HASH from what Felix uploaded the other day.
After receiving Felix file, both have indeed different hashes, however
when unpackaged via `xz -d` both have the same tarball content.
Below the checksums to compare:
a62bef497078c7b825f11fc8358c1a43f5db3e6d4b97812044f7653d60747d5b dl/unetd-2024.03.31~80645766.tar.xz
fbdac59581742bf208c18995b1d69d9848c93bfce487e57ba780d959e0d62fc4 dl/unetd-2024.03.31~80645766_felix.tar.xz
After unpacking:
a7189cae90bc600abf3a3bff3620dc17a9143be8c27d27412de6eb66a1cf1b7d dl/unetd-2024.03.31~80645766.tar
a7189cae90bc600abf3a3bff3620dc17a9143be8c27d27412de6eb66a1cf1b7d dl/unetd-2024.03.31~80645766_felix.tar
The tarball with the wrong hash was accidentally generated without the xz
revert to version 5.4.6
Signed-off-by: Paul Spooren <mail@aparcar.org>
Add patch fixing compilation with kernel 6.6.
class_create now require only the name instead of the module ownership
reference.
Also the kernel enabled checks for enum.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add patch fixing compilation with kernel 6.6.
class_create now require only the name instead of the module ownership
reference.
Also the kernel enabled checks for enum.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
254810d16cf1 watchdog: always close fd on watchdog stop
946552a7b598 trace: use standard POSIX header for basename()
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add debugfs entry for disabling frames buffering that may be a reason
for mt7603 instability. This patch was sent upstream for review and at
least wasn't rejected yet. Let's add it to let OpenWrt users test if it
really helps.
Example usage:
echo N > /sys/kernel/debug/ieee80211/phy0/mt76/frames_buffering
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Build files shouldn't be symlinked into the staging directory, as doing so
would create a race condition if the build folder for 'qca-nss-dp' gets
deleted for any reason.
We should instead just copy over the required platform file to avoid
breaking compilation for any dependent packages.
Signed-off-by: Sean Khan <datapronix@protonmail.com>
The current build procedure always wipes away build files, this is
costly as ssdk is a parent dependency on a whole host of packages and
will always end up rebuilding (and in serial) the whole package.
This patch includes:
1. Module Building Optimization: Instead of creating a temporary
directory (temp) and copying files into it for module building,
the directly invoke the module build command with the
necessary paths. This simplifies the build process
and avoids unnecessary file operations, speeding up
the build process and reducing disk usage.
2. Parallel Build Support: By removing the explicit creation of
the temporary directory and associated file copying operations,
and passing in $(MAKE) $(PKG_JOBS) allows building in parallel.
3. Fix `EXTRA_CFLAGS`: This variable is referenced and set within MAKE_FLAGS,
so doesn't preserve spaces. Should have its defined value quoted.
Signed-off-by: Sean Khan <datapronix@protonmail.com>
52144f723bec pex: after receiving data update req, notify peer of local address/port
29aacb9386e0 pex: track indirect hosts (reachable via gateway) as peers without adding them to wg
48049524d4fc pex: do not send peer notifications for hosts with a gateway
12ac684ee22a pex: do not query for hosts with a gateway
203c88857354 pex: fix endian issues on config transfer
a29d45c71bca network: fix endian issue in converting port to network id
cbbe9d337a17 unet-cli: emit id by default
806457664ab6 unet-cli: strip initial newline in usage message
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Specification:
- MT7981 CPU using 2.4GHz and 5GHz WiFi (both AX)
- MT7531 switch
- 512MB RAM
- 128MB NAND flash with two UBI partitions with identical size
- 1 multi color LED (red, green, blue, white) connected via GCA230718
- 3 buttons (WPS, reset, LED on/off)
- 1 1Gbit WAN port
- 4 1Gbit LAN ports
Disassembly:
- There are four screws at the bottom: 2 under the rubber feets, 2 under the label.
- After removing the screws, the white plastic part can be shifted out of the blue part.
- Be careful because the antennas are mounted on the side and the top of the white part.
Serial Interface
- The serial interface can be connected to the 4 pin holes on the side of the board.
- Pins (from front to rear):
- 3.3V
- RX
- TX
- GND
- Settings: 115200, 8N1
MAC addresses:
- WAN MAC is stored in partition "Odm" at offset 0x81
- LAN (as printed on the device) is WAN MAC + 1
- WLAN MAC (2.4 GHz) is WAN MAC + 2
- WLAN MAC (5GHz) is WAN MAC + 3
Flashing via Recovery Web Interface:
- The recovery web interface always flashes to the currently active partition.
- If OpenWrt is flahsed to the second partition, it will not boot.
- Ensure that you have an OEM image available (encrypted and decrypted version). Decryption is described in the end.
- Set your IP address to 192.168.200.10, subnetmask 255.255.255.0
- Press the reset button while powering on the device
- Keep the reset button pressed until the LED blinks red
- Open a Chromium based and goto http://192.168.200.1 (recovery web interface)
- Download openwrt-mediatek-filogic-dlink_aquila-pro-ai-m30-a1-squashfs-recovery.bin
- The recovery web interface always reports successful flashing, even if it fails
- After flashing, the recovery web interface will try to forward the browser to 192.168.0.1 (can be ignored)
- If OpenWrt was flashed to the first partition, OpenWrt will boot (The status LED will start blinking white and stay white in the end). In this case you're done and can use OpenWrt.
- If OpenWrt was flashed to the second partition, OpenWrt won't boot (The status LED will stay red forever). In this case, the following steps are reuqired:
- Start the web recovery interface again and flash the **decrypted OEM image**. This will be flashed to the second partition as well. The OEM firmware web interface is afterwards accessible via http://192.168.200.1.
- Now flash the **encrypted OEM image** via OEM firmware web interface. In this case, the new firmware is flashed to the first partition. After flashing and the following reboot, the OEM firmware web interface should still be accessible via http://192.168.200.1.
- Start the web recovery interface again and flash the OpenWrt recovery image. Now it will be flashed to the first partition, OpenWrt will boot correctly afterwards and is accessible via 192.168.1.1.
Flashing via U-Boot:
- Open the case, connect to the UART console
- Set your IP address to 192.168.200.2, subnet mask 255.255.255.0. Connect to one of the LAN interfaces of the router
- Run a tftp server which provides openwrt-mediatek-filogic-dlink_aquila-pro-ai-m30-a1-initramfs-kernel.bin.
- Power on the device and select "7. Load image" in the U-Boot menu
- Enter image file, tftp server IP and device IP (if they differ from the default).
- TFTP download to RAM will start. After a few seconds OpenWrt initramfs should start
- The initramfs is accessible via 192.168.1.1, change your IP address accordingly (or use multiple IP addresses on your interface)
- Perform a sysupgrade using openwrt-mediatek-filogic-dlink_aquila-pro-ai-m30-a1-squashfs-sysupgrade.bin
- Reboot the device. OpenWrt should start from flash now
Revert back to stock using the Recovery Web Interface:
- Set your IP address to 192.168.200.2, subnetmask 255.255.255.0
- Press the reset button while powering on the device
- Keep the reset button pressed until the LED blinks red
- Open a Chromium based and goto http://192.168.200.1 (recovery web interface)
- Flash a decrypted firmware image from D-Link. Decrypting an firmware image is described below.
Decrypting a D-Link firmware image:
- Download https://github.com/RolandoMagico/firmware-utils/blob/M32/src/m32-firmware-util.c
- Compile a binary from the downloaded file, e.g. gcc m32-firmware-util.c -lcrypto -o m32-firmware-util
- Run ./m32-firmware-util M30 --DecryptFactoryImage <OriginalFirmware> <OutputFile>
- Example for firmware M30A1_FW101B05: ./m32-firmware-util M30 --DecryptFactoryImage M30A1_FW101B05\(0725091522\).bin M30A1_FW101B05\(0725091522\)_decrypted.bin
Flashing via OEM web interface is not possible, as it will change the active partition and OpenWrt is only running on the first UBI partition.
Controlling the LEDs:
- The LEDs are controlled by a chip called "GCA230718" which is connected to the main CPU via I2C (address 0x40)
- I didn't find any documentation or driver for it, so the information below is purely based on my investigations
- If there is already I driver for it, please tell me. Maybe I didn't search enough
- I implemented a kernel module (leds-gca230718) to access the LEDs via DTS
- The LED controller supports PWM for brightness control and ramp control for smooth blinking. This is not implemented in the driver
- The LED controller supports toggling (on -> off -> on -> off) where the brightness of the LEDs can be set individually for each on cycle
- Until now, only simple active/inactive control is implemented (like when the LEDs would have been connected via GPIO)
- Controlling the LEDs requires three sequences sent to the chip. Each sequence consists of
- A reset command (0x81 0xE4) written to register 0x00
- A control command (for example 0x0C 0x02 0x01 0x00 0x00 0x00 0xFF 0x01 0x00 0x00 0x00 0xFF 0x87 written to register 0x03)
- The reset command is always the same
- In the control command
- byte 0 is always the same
- byte 1 (0x02 in the example above) must be changed in every sequence: 0x02 -> 0x01 -> 0x03)
- byte 2 is set to 0x01 which disables toggling. 0x02 would be LED toggling without ramp control, 0x03 would be toggling with ramp control
- byte 3 to 6 define the brightness values for the LEDs (R,G,B,W) for the first on cycle when toggling
- byte 7 defines the toggling frequency (if toggling enabled)
- byte 8 to 11 define the brightness values for the LEDs (R,G,B,W) for the second on cycle when toggling
- byte 12 is constant 0x87
Comparison to M32/R32:
- The algorithms for decrypting the OEM firmware are the same for M30/M32/R32, only the keys differ
- The keys are available in the GPL sources for the M32
- The M32/R32 contained raw data in the firmware images (kernel, rootfs), the R30 uses a sysupgrade tar instead
- Creation of the recovery image is quite similar, only the header start string changes. So mostly takeover from M32/R32 for that.
- Turned out that the bytes at offset 0x0E and 0x0F in the recovery image header are the checksum over the data area
- This checksum was not checked in the recovery web interface of M32/R32 devices, but is now active in R30
- I adapted the recovery image creation to also calculate the checksum over the data area
- The recovery image header for M30 contains addresses which don't match the memory layout in the DTS. The same addresses are also present in the OEM images
- The recovery web interface either calculates the correct addresses from it or has it's own logic to determine where which information must be written
Signed-off-by: Roland Reinl <reinlroland+github@gmail.com>
Add basic support for the LED driver for GCA230718.
- I didn't find any documentation or driver for it, so the information below is purely based on my investigations
- If there is already I driver for it, please tell me. Maybe I didn't search enough
- I implemented a kernel module (leds-gca230718) to access the LEDs via DTS
- The LED controller supports PWM for brightness control and ramp control for smooth blinking. This is not implemented in the driver
- The LED controller supports toggling (on -> off -> on -> off) where the brightness of the LEDs can be set individually for each on cycle
- Until now, only simple active/inactive control is implemented (like when the LEDs would have been connected via GPIO)
- Controlling the LEDs requires three sequences sent to the chip. Each sequence consists of
- A reset command (0x81 0xE4) written to register 0x00
- A control command (for example 0x0C 0x02 0x01 0x00 0x00 0x00 0xFF 0x01 0x00 0x00 0x00 0xFF 0x87 written to register 0x03)
- The reset command is always the same
- In the control command
- byte 0 is always the same
- byte 1 (0x02 in the example above) must be changed in every sequence: 0x02 -> 0x01 -> 0x03)
- byte 2 is set to 0x01 which disables toggling. 0x02 would be LED toggling without ramp control, 0x03 would be toggling with ramp control
- byte 3 to 6 define the brightness values for the LEDs (R,G,B,W) for the first on cycle when toggling
- byte 7 defines the toggling frequency (if toggling enabled)
- byte 8 to 11 define the brightness values for the LEDs (R,G,B,W) for the second on cycle when toggling
- byte 12 is constant 0x87
Signed-off-by: Roland Reinl <reinlroland+github@gmail.com>
