Commit Graph

146 Commits

Author SHA1 Message Date
Robert Marko
eb564690c9 ipq40xx: add support for Wallystech DR40x9
Adds support for the Wallys DR40x9 series boards.
They come in IPQ4019 and IPQ4029 versions.
IPQ4019/4029 only differ in that that IPQ4029 is the industrial version that is rated to higher temperatures.

Specifications are:
* CPU: Qualcomm IPQ40x9 (4x ARMv7A Cortex A7) at 716 MHz
* RAM: 512 MB
* Storage: 2MB of SPI-NOR, 128 MB of parallel NAND
* USB 3.0 TypeA port for users
* MiniPCI-E with PCI-E 2.0 link
* MiniPCI-E for LTE modems with only USB2.0 link
* 2 SIM card slots that are selected via GPIO11
* MicroSD card slot
* Ethernet: 2x GBe with 24~48V passive POE
* SFP port (Does not work, I2C and GPIO's not connected on hardware)
* DC Jack
* UART header
* WLAN: In-SoC 2x2 802.11b/g/n and 2x2 802.11a/n/ac
* 4x MMCX connectors for WLAN
* Reset button
* 8x LED-s

Installation instructions:
Connect to UART, pins are like this:
-> 3.3V | TX | RX | GND

Settings are 115200 8n1

Boot initramfs from TFTP:
tftpboot 0x84000000 openwrt-ipq40xx-generic-wallys_dr40x9-initramfs-fit-uImage.itb

bootm

Then copy the sysupgrade image to the /tmp folder and execute sysupgrade -n <image_name>

The board file binary was provided from Wallystech on March 14th 2023
including full permission to use and distribute.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Signed-off-by: Koen Vandeputte <koen.vandeputte@citymesh.com>
2023-03-21 16:38:23 +01:00
David Bauer
bf055fcdca ipq40xx: convert Netgear EX6100/EX6150 v2 to DSA
Signed-off-by: David Bauer <mail@david-bauer.net>
2023-03-08 02:19:01 +01:00
James Andrewartha
7c04e80f87 ipq40xx: convert Extreme AP3915i to DSA
Convert and re-enabled Extreme AP3915i to DSA.

Signed-off-by: James Andrewartha <trs80@ucc.asn.au>
2023-01-17 23:45:44 +01:00
Martin Schiller
539b52068a ipq40xx: add DSL support for FritzBox 7530
Set up MAC, LED, settings and default packages for DSL usage, similar
to the lantiq target.

Due to licensing uncertainty, we do not include the firmware files for the
DSL drivers. To have a working DSL setup, follow the instructions below.

Download the firmware files locally:

  mkdir -p files/lib/firmware/09a9
  wget -P files/lib/firmware/09a9 https://gitlab.com/prpl-foundation/intel/vrx518_aca_fw/-/raw/ugw-8.5.2/platform/xrx500/aca_fw.bin
  wget -P files/lib/firmware https://gitlab.com/prpl-foundation/intel/vrx518_ppe_fw/-/raw/ugw_8.5.2.10/platform/xrx500/ppe_fw.bin
  wget -P files/lib/firmware https://gitlab.com/prpl-foundation/intel/dsl_vr11_firmware_xdsl/-/raw/ugw-8.5.2/xcpe_8D1507_8D0901.bin
  ln -s xcpe_8D1507_8D0901.bin files/lib/firmware/vdsl.bin

For people building their own images:

Run the above commands in the root of your local OpenWrt clone,
and the firmware files will be part of the resulting images.

For people downloading images:

Copy the firmware files onto the router once it's booted up:
  scp -O -r files/lib/firmware root@fritz:/lib
Reboot the device afterwards.

Signed-off-by: Martin Schiller <ms.3headeddevs@gmail.com>
[cleaned up]
Signed-off-by: Andre Heider <a.heider@gmail.com>
[set up LED]
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Signed-off-by: Andre Heider <a.heider@gmail.com>
2023-01-16 23:41:41 +00:00
Vincent Tremblay
9e4ede8344 ipq40xx: add support for Linksys WHW03 V2
SOC:             Qualcomm IPQ4019
WiFi 1:          QCA4019 IEEE 802.11b/g/n
WiFi 2:          QCA4019 IEEE 802.11a/n/ac
WiFi 3:          QCA8888 IEEE 802.11a/n/ac
Bluetooth:       Qualcomm CSR8811 (A12U)
Zigbee:          Silicon Labs EM3581 NCP + Skyworks SE2432L
Ethernet:        Qualcomm Atheros QCA8072 (2-port)
Flash 1:         Mactronix MX30LF4G18AC-XKI
RAM (NAND):      SK hynix H5TC4G63CFR-PBA (512MB)
LED Controller:  NXP PCA9633 (I2C)
Buttons:         Single reset button (GPIO).

- The three WiFis were fully tested and are configured with the same settings as in the vendor firmware.
- The specific board files were submitted to the ATH10k mailing list but I'm still waiting for a reply. They can be removed once they are approved upstream.
- Two ethernet ports are accessible on the device. By default one is configured as WAN and the other one is LAN. They are fully working.

Bluetooth:
========
- Fully working with the following caveats:
  - RFKILL need to be enabled in the kernel.
  - An older version of bluez is needed as bccmd is needed to configure the chip.

Zigbee:
======
- The spidev device is available in the /dev directory.
- GPIOs are configured the same way as in the vendor firmware.
- Tests are on-going. I am working on getting access to the Silicon Labs stack to validate that it is fully working.

Installation:
=========
The squash-factory image can be installed via the Linksys Web UI:
1. Open "http://192.168.1.1/ca" (Change the IP with the IP of your device).
2. Login with your admin password.
3. To enter into the support mode, click on the "CA" link and the bottom of the page.
4. Open the "Connectivity" menu and upload the squash-factory image with the "Choose file" button.
5. Click start. Ignore all the prompts and warnings by click "yes" in all the popups.

The device uses a dual partition mechanism. The device automatically revert to the previous partition after 3 failed boot attempts.
If you want to force the previous firmware to load, you can turn off and then turn on the device for 2 seconds, 3 times in a row.

It can also be done via TFTP:
1. Setup a local TFTP server and configure its IP to 192.168.1.100.
2. Rename your image to "nodes_v2.img" and put it to the TFTP root of your server.
3. Connect to the device through the serial console.
4. Power on device and press enter when prompted to drop into U-Boot.
5. Flash the partition of your choice by typing "run flashimg" or "run flashimg2".
6. Once flashed, enter "reset" to reboot the device.

Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Vincent Tremblay <vincent@vtremblay.dev>
2023-01-15 12:55:38 +01:00
Marcin Gajda
700c47a5f6 ipq40xx: Add support ZTE MF18A
Light and small router ( In Poland operators sells together with MC7010 outdoor modem to provide WIFI inside home).
Device specification

SoC Type: Qualcomm IPQ4019
RAM: 256 MiB
Flash: 128 MiB SPI NAND (Winbond W25N01GV)
ROM: 2MiB SPI Flash (GD25Q16)
Wireless 2.4 GHz (IP4019): b/g/n, 2x2
Wireless 5 GHz (QCA9982): a/n/ac, 3x3
Ethernet: 2xGbE (WAN/LAN1, LAN2)
USB ports: No
Button: 2 (Reset/WPS)
LEDs: 3 external leds: Power (blue) , WiFI (blue and red), SMARTHOME (blue and red) and 1 internal (blue) -- NOTE: Power controls all external led (if down ,all others also not lights even signal is up)
Power: 5VDC, 2,1A via USB-C socket
Bootloader: U-Boot
On board ZWave and Zigbee (EFR32 MG1P232GG..)  modules ( not supported by orginal software )
Installation

 1.Open MF18A case by ungluing rubber pad under the router and unscrew screws, and connect to serial console port,
   with the following pinout, starting from pin 1, which is the topmost pin when the board is upright (reset button on the bottom) :

    VCC (3.3V). Do not use unless you need to source power for the converer from it.
    TX
    RX
    GND

    Default port configuration in U-boot as well as in stock firmware is 115200-8-N-1.

 2.Place OpenWrt initramfs image for the device on a TFTP in the server's root. This example uses Server IP: 192.168.0.2

 3.Connect TFTP server to RJ-45 port (WAN/LAN1).

 4.Power on MF18A , stop in u-Boot (using ESC button) and run u-Boot commands:
    setenv serverip 192.168.0.2
    setenv ipaddr 192.168.0.1
    set fdt_high 0x85000000
    tftpboot 0x84000000 openwrt-ipq40xx-generic-zte_mf18a-initramfs-fit-zImage.itb
    bootm 0x84000000

 5.Please make backup of original partitions, if you think about revert to stock, specially mtd8 (Web UI) and mtd9 (rootFS). Use /tmp as temporary storage and do:

WEB PARITION

cat /dev/mtd8 > /tmp/mtd8.bin
scp /tmp/mtd8.bin root@YOURSERVERIP:/
rm /tmp/mtd8.bin
ROOT PARITION

cat /dev/mtd9 > /tmp/mtd9.bin
scp /tmp/mtd9.bin root@YOURSERVERIP:/
rm /tmp/mtd9.bin

If you are sure ,that you want to flash openwrt, from uBoot, before bootm, clean rootfs partition with command:
nand erase 0x1800000 0x1D00000

 6.Login via ssh or serial and remove stock partitions (default IP 192.168.1.1):
ubiattach -m 9 # it could return error if ubi was attached before or rootfs part was erased before
ubirmvol /dev/ubi0 -N ubi_rootfs # it could return error if rootfs part was erased before
ubirmvol /dev/ubi0 -N ubi_rootfs_data # some devices doesn't have it

 7. Install image via :
sysupgrade -n /tmp/openwrt-ipq40xx-generic-zte_mf18a-squashfs-sysupgrade.bin

previously wgeting bin. Sometimes it could print ubi attach error, but please ignore it if process goes forward.

Back to Stock (!!! need original dump taken from initramfs !!!) -------------

Place mtd8.bin and mtd9.bin initramfs image for the device on a TFTP in the server's root. This example uses Server IP: 192.168.0.2
Connect serial console (115200,8n1) to serial console connector .
Connect TFTP server to RJ-45 port (WAN/LAN1).
rename mtd8.bin to web.img and mtd9.bin to root_uImage_s
Stop in u-Boot (using ESC button) and run u-Boot commands:
This will erase Web and RootFS:
nand erase 0x1000000 0x800000
nand erase 0x1800000 0x1D00000

This will restore RootFS:
tftpboot 0x84000000 root_uImage_s
nand erase 0x1800000 0x1D00000
nand write 0x84000000 0x1800000 0x1D00000

This will restore Web Interface:
tftpboot 0x84000000 web.img
nand erase 0x1000000 0x800000
nand write 0x84000000 0x1000000 0x800000

After first boot on stock firwmare, do a factory reset. Push reset button for 5 seconds so all parameters will be reverted to the one printed on label on bottom of the router

As reference was taken MF289F support by Giammarco Marzano stich86@gmail.com and MF286D by Pawel Dembicki paweldembicki@gmail.com

Signed-off-by: Marcin Gajda <mgajda@o2.pl>
2023-01-14 19:19:36 +01:00
Tony Ambardar
4b367e2b60 ipq40xx: migrate Linksys WHW01 to DSA and re-enable
Convert Linksys WHW01 network configuration to DSA and re-enable builds.

Reviewed-by: Robert Marko <robimarko@gmail.com>
Tested-by: Wyatt Martin <wawowl@gmail.com>
Signed-off-by: Wyatt Martin <wawowl@gmail.com>
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
2022-12-31 05:02:38 -08:00
Tony Ambardar
2a9f3b7717 ipq40xx: fix up Linksys WHW01 board name, device definition
Update the board name defined in DTS to match online documentation and the
name encoded into factory firmware. This helps supports flashing firmware
factory images using 'sysupgrade'.

Original WHW01 device definition assumes the rootfs IMAGE_SIZE is 33 MB
instead of the correct 74 MB, and defines factory images which include
extra adjustments/padding that do not match OEM factory images and may
cause problems flashing. Update image size and build recipe to fix these.

Suggested-by: Wyatt Martin <wawowl@gmail.com>
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
2022-12-31 05:02:38 -08:00
Tony Ambardar
cda6f1c832 ipq40xx: re-enable EA6350v3, EA8300, MR8300 builds
Raise the kernel size from 3 MB to 5 MB for EA6350v3, EA8300 and MR8300,
and correspondingly reduce the rootfs size by 2 MB:
  * modify partition definitions in related .dts files
  * modify device kernel/image sizes in generic.mk

Update to compat-version 2.0 to force factory image usage on sysupgrade,
noting the current version 1.1 is an unreleased update for DSA migration.

Also update the compat-version message, explaining the need to run one of
the following console commands to update U-Boot's kernel-size variable
before flashing the OpenWrt factory image.

    fw_setenv kernsize 500000          # (OpenWrt command line)

    setenv kernsize 500000 ; saveenv   # (U-Boot serial console)

Finally, re-enable the 3 devices.

Reviewed-by: Robert Marko <robimarko@gmail.com>
Tested-by: Nicolas TORMO <badulesia.granieri@gmail.com> # MR8300
Tested-by: Tony Ambardar <itugrok@yahoo.com> # EA6350v3
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
2022-12-31 05:02:38 -08:00
Nick Hainke
3195a992d6
ipq40xx: convert Aruba AP-303H to DSA and enable target again
The target was disabled since noone did the DSA conversion. Add the
conversion and enable it again.

Tested-by: John Walshaw <jjw@myself.com>
Signed-off-by: Bjoern Dobe <bjoern@dobecom.de>
Signed-off-by: Nick Hainke <vincent@systemli.org>
2022-12-29 17:39:30 +01:00
Alexander Couzens
d4c460648d
ipq40xx: add support for Mikrotik wAP R ac / LTE / LTE6
The Mikrotik wAP R AC is an outdoor, dual band, dual radio (802.11ac) AP
with a miniPCIe slot for a LTE modem.
The wAP R AC is similar to the wAP AC but with the miniPCIe slot.
The wAP R AC requires installing a LTE modem.
The wAP LTE and wAP LTE6 comes with a LTE modem installed.

See https://mikrotik.com/product/wap_r_ac for more info.

Specifications:
- SoC: Qualcomm Atheros IPQ4018
- CPU: 4x ARM Cortex A7
- RAM: 128MB
- Storage: 16MB NOR flash
- Wireless:
   - Built-in IPQ4018 (SoC) 802.11b/g/n 2x2:2, internal antenna
   - Built-in IPQ4018 (SoC) 802.11a/n/ac 2x2:2, internal antenna
- Ethernet: Built-in IPQ4018 (SoC, QCA8075) , 2x 1000/100/10 ports
  one with 802.3af/at PoE in
- 1x Mini PCI-E port (USB2)

Installation:
Boot the initramfs image via TFTP, then flash the sysupgrade image using
sysupgrade. Details at https://openwrt.org/toh/mikrotik/common.

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
2022-11-27 13:28:22 +00:00
Sven Eckelmann
fc69532eb9 ipq40xx: Convert plasmacloud,pa2200 to DSA
* ethernet1:

  - physical port label "Ethernet 1"
  - its mac address is printed on the device label

* ethernet2:

  - physical port label "Ethernet 2"
  - can be used to power the device

Both ports are not marked by there role (because the vendor firmware
automatically detects roles) but the "Ethernet 2" port was used in the past
for "WAN" functionality in OpenWrt.

Tested-by: Michaël BILCOT <michael.bilcot@gmail.com>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
2022-11-13 15:26:34 +01:00
Sven Eckelmann
ce6c9e0328 ipq40xx: utilize nvmem-cells for plasmacloud,pa2200
The calibration data and mac addresses on this device are stored in the
0:ART partition. It is therefore possible to move the code to handle them
directly to the devicetree instead of the various scripts.

But the actual relevant information about the partition layout is provided
by the bootloader via bootargs (mtdparts) and not via the devicetree
itself. Instead of using a fixed-partition template, the mtd dynamic
partitions support from the upstream kernel is used.

Reported-by: Robert Marko <robert.marko@sartura.hr>
Tested-by: Michaël BILCOT <michael.bilcot@gmail.com>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
2022-11-13 15:26:34 +01:00
Sven Eckelmann
539a5fd624 ipq40xx: Convert plasmacloud,pa1200 to DSA
* ethernet1:

  - physical port label "Ethernet 1"
  - its mac address is printed on the device label

* ethernet2:

  - physical port label "Ethernet 2"
  - can be used to power the device

Both ports are not marked by there role (because the vendor firmware
automatically detects roles) but the "Ethernet 2" port was used in the past
for "WAN" functionality in OpenWrt.

Signed-off-by: Sven Eckelmann <sven@narfation.org>
2022-11-13 15:26:34 +01:00
Sven Eckelmann
b8bda645fc ipq40xx: utilize nvmem-cells for plasmacloud,pa1200
The calibration data and mac addresses on this device are stored in the
0:ART partition. It is therefore possible to move the code to handle them
directly to the devicetree instead of the various scripts.

But the actual relevant information about the partition layout is provided
by the bootloader via bootargs (mtdparts) and not via the devicetree
itself. Instead of using a fixed-partition template, the mtd dynamic
partitions support from the upstream kernel is used.

Reported-by: Robert Marko <robert.marko@sartura.hr>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
2022-11-13 15:26:34 +01:00
Sven Eckelmann
087a8e39be ipq40xx: utilize nvmem-cells for openmesh,a62
The calibration data and mac addresses on this device are stored in the
0:ART partition. It is therefore possible to move the code to handle them
directly to the devicetree instead of the various scripts.

But the actual relevant information about the partition layout is provided
by the bootloader via bootargs (mtdparts) and not via the devicetree
itself. Instead of using a fixed-partition template, the mtd dynamic
partitions support from the upstream kernel is used.

Reported-by: Robert Marko <robert.marko@sartura.hr>
Reviewed-by: Robert Marko <robimarko@gmail.com>
Tested-by: Michaël BILCOT <michael.bilcot@gmail.com>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
2022-11-12 18:15:55 +01:00
Sven Eckelmann
2b2f14c959 ipq40xx: utilize nvmem-cells for openmesh,a42
The calibration data and mac addresses on this device are stored in the
0:ART partition. It is therefore possible to move the code to handle them
directly to the devicetree instead of the various scripts.

But the actual relevant information about the partition layout is provided
by the bootloader via bootargs (mtdparts) and not via the devicetree
itself. Instead of using a fixed-partition template, the mtd dynamic
partitions support from the upstream kernel is used.

Reported-by: Robert Marko <robert.marko@sartura.hr>
Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
2022-11-12 18:15:55 +01:00
Sven Eckelmann
c6bef1b83a ipq40xx: Convert openmesh,a62 to DSA
* ethernet1:

  - physical port label "Ethernet 1"
  - can be used to power the device
  - its mac address is printed on the device label

* ethernet2:

  - physical port label "Ethernet 2"

Both ports are not marked by there role (because the vendor firmware
automatically detects roles) but the "Ethernet 1" port was used in the past
for "WAN" functionality in OpenWrt.

Reviewed-by: Robert Marko <robimarko@gmail.com>
Tested-by: Michaël BILCOT <michael.bilcot@gmail.com>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
2022-11-12 18:15:55 +01:00
Sven Eckelmann
66a3c32b47 ipq40xx: Convert openmesh,a42 to DSA
* ethernet1:

  - physical port label "Ethernet 1"
  - can be used to power the device
  - its mac address is printed on the device label

* ethernet2:

  - physical port label "Ethernet 2"

Both ports are not marked by there role (because the vendor firmware
automatically detects roles) but the "Ethernet 1" port was used in the past
for "WAN" functionality in OpenWrt.

Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
2022-11-12 18:15:55 +01:00
Guillaume Lefebvre
65d9a715fc ipq40xx: D-Link DAP-2610: convert to DSA
Reenable D-Link DAP-2610, convert it to DSA and label port to 'lan', as shown on the case

Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Guillaume Lefebvre <guillaume@zelig.ch>
2022-11-12 18:15:55 +01:00
Weiping Yang
9945d05171 ipq40xx: add support for GL.iNet GL-A1300
Specifications:
SOC:		Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core
RAM:		256 MiB
FLASH1:		4 MiB NOR
FLASH2:		128 MiB NAND
ETH:		Qualcomm QCA8075
WLAN1:		Qualcomm Atheros QCA4018 2.4GHz 802.11b/g/n 2x2
WLAN2:		Qualcomm Atheros QCA4018 5G 802.11n/ac W2 2x2
USB:		1 x USB 3.0 port
Button:		1 x Reset button
Switch:		1 x Mode switch
LED:		1 x Blue LED + 1 x White LED

Install via uboot tftp or uboot web failsafe.

By uboot tftp:
(IPQ40xx) # tftpboot 0x84000000 openwrt-ipq40xx-generic-glinet_gl-a1300-squashfs-nand-factory.ubi
(IPQ40xx) # nand erase 0 0x8000000
(IPQ40xx) # nand write 0x84000000 0 $filesize

By uboot web failsafe:
Push the reset button for 10 seconds util the power led flash faster,
then use broswer to access http://192.168.1.1

Afterwards upgrade can use sysupgrade image.

Signed-off-by: Weiping Yang <weiping.yang@gl-inet.com>
2022-11-09 23:34:37 +01:00
Csaba Sipos
cc8b8f1b41 ipq40xx: add support for MikroTik hAP ac3 LTE6 kit
This adds support for the MikroTik RouterBOARD RBD53GR-5HacD2HnD
(hAP ac³ LTE6 kit), an  indoor dual band, dual-radio 802.11ac
wireless AP with built-in Mini PCI-E LTE modem, one USB port, five
10/100/1000 Mbps Ethernet ports.

See https://mikrotik.com/product/hap_ac3_lte6_kit for more info.

Specifications:
 - SoC: Qualcomm Atheros IPQ4019
 - RAM: 256 MB
 - Storage: 16 MB NOR
 - Wireless:
   · Built-in IPQ4019 (SoC) 802.11b/g/n 2x2:2, 3 dBi internal antennae
   · Built-in IPQ4019 (SoC) 802.11a/n/ac 2x2:2, 5.5 dBi internal antennae
 - Ethernet: Built-in IPQ4019 (SoC, QCA8075) , 5x 1000/100/10 port
 - 1x USB Type A port
 - 1x Mini PCI-E port (supporting USB)
 - 1x Mini PCI-E LTE modem (MikroTik R11e-LTE6, Cat.6)

Installation:

Make sure your unit is runnning RouterOS v6 and RouterBOOT v6 (tested on 6.49.6).

0. Export your MikroTik license key (in case you want to use the device with RouterOS later)
1. Boot the initramfs image via TFTP
2. Upload the "openwrt-ipq40xx-mikrotik-mikrotik_hap-ac3-lte6-kit-squashfs-sysupgrade.bin" via SCP to the /tmp folder
3. Use sysupgrade to flash the image: sysupgrade -n /tmp/openwrt-ipq40xx-mikrotik-mikrotik_hap-ac3-lte6-kit-squashfs-sysupgrade.bin
4. Recovery to factory software is possible via Netinstall:
   https://help.mikrotik.com/docs/display/ROS/Netinstall

Signed-off-by: Csaba Sipos <metro4@freemail.hu>
2022-10-30 23:14:45 +01:00
Davide Fioravanti
8d921167e9
ipq40xx: convert to DSA and enable Netgear Orbi devices
Convert to DSA and enable again Netgear Orbi devices:
 - RBR50
 - RBS50
 - SRR60
 - SRS60

Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
2022-10-25 02:34:46 +02:00
Brian Norris
a3da858ab0 ipq40xx: Convert Google Wifi to DSA, reenable
Undo parts of these:

116feb4a1c ipq40xx: remove non-converted network configs
db19efee95 ipq40xx: disable boards not converted to DSA

Reintroduce the DT paths /soc/edma@c080000/gmac{0,1}, because the stock
bootloader has memorized them (instead of following aliases); then plug
the MAC address back in via 05_set_iface_mac_ipq40xx.sh, since the
'local-mac-address' property is no longer in the correct node.

Cc: David Bauer <mail@david-bauer.net>
Cc: Robert Marko <robert.marko@sartura.hr>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2022-10-23 08:27:40 +02:00
Jack Chen
57577bb8cc ipq40xx: convert to DSA and enable mobipromo,cm520-79f
Convert to DSA and enable the MobiPromo CM520-79F device again.

Signed-off-by: Jack Chen <redchenjs@live.com>
Reviewed-by: Robert Marko <robimarko@gmail.com>
2022-10-23 01:45:52 +02:00
Chen Minqiang
3505933073 ipq40xx: convert to DSA and enable asus,rt-ac42u
This convert board asus,rt-ac42u to DSA and re-enable it

Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
2022-10-22 20:09:58 +08:00
Mark Mentovai
9a8e008188 ipq40xx: Convert mikrotik,wap-ac to DSA
As done previously, this preserves the MAC addresses of they physical
Ethernet ports. The interfaces are renamed as eth0 is in use for the
native GMAC; the new interface naming matches the physical port labels.
 - sw-eth1 corresponds to the physical port labeled ETH1 and has the
   base MAC address. This port can be used to power the device.
 - sw-eth2 corresponds to the physical port labeled ETH2 and has a MAC
   address one greater than the base.

As this device has 2 physical ports, they are each connected to their
respective PHYs, allowing the link status to be visible to software.
Since they are not marked on the case with any role (such as LAN or
WAN), both are bridged to the lan network by default, although this can
easily be changed if needed.

Signed-off-by: Mark Mentovai <mark@mentovai.com>
2022-10-19 22:58:12 +02:00
INAGAKI Hiroshi
32e41ba18a ipq40xx: convert to DSA and enable Sony NCP-HG100/Cellular
This patch converts networking on Sony NCP-HG100/Cellular to DSA and
re-enables support for the device.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2022-10-09 22:45:06 +02:00
Dirk Buchwalder
579ea6b970 ipq40xx: ZTE MF289F: convert to DSA
Convert ZTE MF289F device to DSA, re-order network ports to match the
labels on the case and re-enable the device.

Signed-off-by: Dirk Buchwalder <buchwalder@posteo.de>
Reviewed-by: Robert Marko <robimarko@gmail.com>
Reviewed-by: Lech Perczak <lech.perczak@gmail.com>
2022-10-09 22:39:48 +02:00
Tomasz Maciej Nowak
ee38573093
ipq40xx: pakedge_wr-1: convert to DSA
Convert pakedge_wr-1 device to DSA and enable it.

Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Reviewed-by: Robert Marko <robimarko@gmail.com>i
[ improve commit description ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-10-05 19:16:52 +02:00
Tomasz Maciej Nowak
70d9193b51
ipq40xx: luma_wrtq-329acn: convert to DSA
Convert luma_wrtq-329acn device to DSA and enable it.

Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Reviewed-by: Robert Marko <robimarko@gmail.com>
[ improve commit description ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-10-05 19:10:28 +02:00
Robert Marko
116feb4a1c ipq40xx: remove non-converted network configs
Remove networking configs for non DSA converted boards in ipq40xx.
Currently, they are just causing clutter.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2022-10-02 23:04:39 +02:00
Lech Perczak
b9b4c51b2b ipq40xx: Meraki MR33: convert MAC addresses to nvmem
This fixes assigning random MAC to br-lan interface upon boot.
While at that, rename at24@50 node to eeprom@50, to align with upstream
device tree style.

Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
2022-10-02 23:04:39 +02:00
Robert Marko
550253bdf9 ipq40xx: convert some boards to DSA
Convert IPQ40xx boards to DSA setup.

Signed-off-by: Leon M. George <leon@georgemail.eu>
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Signed-off-by: Nick Hainke <vincent@systemli.org>
Signed-off-by: ChunAm See <z1250747241@gmail.com>
Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
Signed-off-by: Andrew Sim <andrewsimz@gmail.com>
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2022-10-02 23:04:39 +02:00
Giammarco Marzano
0de6a3339f ipq40xx: Add ZTE MF289F
It's a 4G Cat.20 router used by Vodafone Italy (called Vodafone FWA)
and Vodafone DE\T-Mobile PL (called GigaCube).

Modem is a MiniPCIe-to-USB based on Snapdragon X24,
it supports 4CA aggregation.

There are currently two hardware revisions, which
differ on the 5Ghz radio:

AT1 = QCA9984 5Ghz Radio on PCI-E bus
AT2 = IPQ4019 5Ghz Radio inside IPQ4019 like 2.4Ghz

Device specification
--------------------
SoC Type: Qualcomm IPQ4019
RAM: 256 MiB
Flash: 128 MiB SPI NAND (Winbond W25N01GV)
ROM: 2MiB SPI Flash (GD25Q16)
Wireless 2.4 GHz (IP4019): b/g/n, 2x2
Wireless 5 GHz:
	(QCA9984): a/n/ac, 4x4 HW REV AT1
	(IPA4019): a/n/ac, 2x2 HW REV AT2
Ethernet: 2xGbE (WAN/LAN1, LAN2)
USB ports: No
Button: 2 (Reset/WPS)
LEDs: 3 external leds: Network (white or red), Wifi, Power and 1 internal (blue)
Power: 12 VDC, 1 A
Connector type: Barrel
Bootloader: U-Boot

Installation
------------
1. Place OpenWrt initramfs image for the device on a TFTP
   in the server's root. This example uses Server IP: 192.168.0.2
2. Connect serial console (115200,8n1) to serial connector
   GND (which is right next to the thing with MF289F MIMO-V1.0), RX, TX
   (refer to this image: https://ibb.co/31Gngpr).
3. Connect TFTP server to RJ-45 port (WAN/LAN1).
4. Stop in u-Boot (using ESC button) and run u-Boot commands:

setenv serverip 192.168.0.2
setenv ipaddr 192.168.0.1
set fdt_high 0x85000000
tftp openwrt-ipq40xx-generic-zte_mf289f-initramfs-fit-zImage.itb
bootm $loadaddr

5. Please make backup of original partitions, if you think about revert to
   stock, specially mtd16 (Web UI) and mtd17 (rootFS).
Use /tmp as temporary storage and do:

WEB PARITION
--------------------------------------
cat /dev/mtd16 > /tmp/mtd16.bin
scp /tmp/mtd16.bin root@YOURSERVERIP:/
rm /tmp/mtd16.bin

ROOT PARITION
--------------------------------------
cat /dev/mtd17 > /tmp/mtd17.bin
scp /tmp/mtd17.bin root@YOURSERVERIP:/
rm /tmp/mtd17.bin

6. Login via ssh or serial and remove stock partitions
   (default IP 192.168.0.1):

 # this can return an error, if ubi was attached before
 # or rootfs part was erased before.
ubiattach -m 17

 # it could return error if rootfs part was erased before
ubirmvol /dev/ubi0 -N ubi_rootfs
 # some devices doesn't have it
ubirmvol /dev/ubi0 -N ubi_rootfs_data

7. download and install image via sysupgrade -n
 (either use wget/scp to copy the mf289f's squashfs-sysupgrade.bin
 to the device's /tmp directory)

 sysupgrade -n /tmp/openwrt-...-zte_mf289f-squashfs-sysupgrade.bin

Sometimes it could print ubi attach error, but please ignore it
if process goes forward.

Flash Layout

NAND:
mtd8: 000a0000 00020000 "fota-flag"
mtd9: 00080000 00020000 "0:ART"
mtd10: 00080000 00020000 "mac"
mtd11: 000c0000 00020000 "reserved2"
mtd12: 00400000 00020000 "cfg-param"
mtd13: 00400000 00020000 "log"
mtd14: 000a0000 00020000 "oops"
mtd15: 00500000 00020000 "reserved3"
mtd16: 00800000 00020000 "web"
mtd17: 01d00000 00020000 "rootfs"
mtd18: 01900000 00020000 "data"
mtd19: 03200000 00020000 "fota"
mtd20: 0041e000 0001f000 "kernel"
mtd21: 0101b000 0001f000 "ubi_rootfs"

SPI:
mtd0: 00040000 00010000 "0:SBL1"
mtd1: 00020000 00010000 "0:MIBIB"
mtd2: 00060000 00010000 "0:QSEE"
mtd3: 00010000 00010000 "0:CDT"
mtd4: 00010000 00010000 "0:DDRPARAMS"
mtd5: 00010000 00010000 "0:APPSBLENV"
mtd6: 000c0000 00010000 "0:APPSBL"
mtd7: 00050000 00010000 "0:reserved1"

Back to Stock (!!! need original dump taken from initramfs !!!)
-------------
1. Place mtd16.bin and mtd17.bin initramfs image
   for the device on a TFTP in the server's root.
   This example uses Server IP: 192.168.0.2
2. Connect serial console (115200,8n1) to serial console
   connector (refer to the pin-out from above).
3. Connect TFTP server to RJ-45 port (WAN/LAN1).
4. rename mtd16.bin to web.img and mtd17.bin to root_uImage_s
5. Stop in u-Boot (using ESC button) and run u-Boot commands:

This will erase RootFS+Web:
nand erase 0x1000000 0x800000
nand erase 0x1800000 0x1D00000

This will restore RootFS:
tftpboot 0x84000000 ${dir}root_uImage_s
nand erase 0x1800000 0x1D00000
nand write $fileaddr 0x1800000 $filesize

This will restore Web Interface:
tftpboot 0x84000000 ${dir}web.img
nand erase 0x1000000 0x800000
nand write $fileaddr 0x1000000 $filesize

After first boot on stock firwmare, do a factory reset.
Push reset button for 5 seconds so all parameters will
be reverted to the one printed on label on bottom of the router

Signed-off-by: Giammarco Marzano <stich86@gmail.com>
Reviewed-by: Lech Perczak <lech.perczak@gmail.com>
(Warning: commit message did not conform to UTF-8 - hopefully fixed?,
added description of the pin-out if image goes down, reformatted
commit message to be hopefully somewhat readable on git-web,
redid some of the gpio-buttons & leds DT nodes, etc.)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-09-24 23:53:53 +02:00
INAGAKI Hiroshi
c34f071972 ipq40xx: add support for Sony NCP-HG100/Cellular
Sony NCP-HG100/Cellular is a IoT Gateway with 2.4/5 GHz band 11ac
(WiFi-5) wireless function, based on IPQ4019.

Specification:

- SoC                   : Qualcomm IPQ4019
- RAM                   : DDR3 512 MiB (H5TC4G63EFR)
- Flash                 : eMMC 4 GiB (THGBMNG5D1LBAIT)
- WLAN                  : 2.4/5 GHz 2T2R (IPQ4019)
- Ethernet              : 10/100/1000 Mbps x2
  - Transceiver         : Qualcomm QCA8072
- WWAN                  : Telit LN940A9
- Z-Wave                : Silicon Labs ZM5101
- Bluetooth             : Qualcomm CSR8811
- Audio DAC             : Realtek ALC5629
- Audio Amp.            : Realtek ALC1304
- Voice Input Processor : Conexant CX20924
- Micro Controller Unit : Nuvoton MINI54FDE
  - RGB LED, Fan, Temp. sensors
- Touch Sensor          : Cypress CY8C4014LQI
- RGB LED driver        : TI LP55231 (2x)
- LEDs/Keys             : 11x, 6x
- UART                  : through-hole on PCB
  - J1: 3.3V, TX, RX, GND from tri-angle marking
  - 115200n8
- Power                 : 12 VDC, 2.5 A

Flash instruction using initramfs image:

1. Prepare TFTP server with the IP address 192.168.132.100 and place the
   initramfs image to TFTP directory with the name "C0A88401.img"

2. Boot NCP-HG100/Cellular and interrupt after the message
   "Hit any key to stop autoboot:  2"

3. Perform the following commands and set bootcmd to allow booting from
   eMMC

   setenv bootcmd "mmc read 0x84000000 0x2e22 0x4000 && bootm 0x84000000"
   saveenv

4. Perform the following command to load/boot the OpenWrt initramfs image

   tftpboot && bootm

5. On the initramfs image, perform sysupgrade with the sysupgrade image
   (if needed, backup eMMC partitions by dd command and download to
   other place before performing sysupgrade)

6. Wait for ~120 seconds to complete flashing

Known issues:

- There are no drivers for audio-related chips/functions in Linux Kernel
  and OpenWrt, they cannot be used.

- There is no driver for MINI54FDE Micro-Controller Unit, customized for
  this device by the firmware in the MCU. This chip controls the
  following functions, but they cannot be controlled in OpenWrt.

  - RGB LED
  - Fan
    this fan is controlled automatically by MCU by default, without
    driver
  - Thermal Sensors (2x)

- Currently, there is no driver or tool for CY8C4014LQI and cannot be
  controlled. It cannot be exited from "booting mode" and moved to "normal
  op mode" after booting. And also, the 4x buttons (mic mute, vol down,
  vol up, alexa trigger) connected to the IC cannot be controlled.

  - it can be exited from "booting mode" by installing and executing
    i2cset command:

    opkg update
    opkg install i2c-tools
    i2cset -y 1 0x14 0xf 1

- There is a connection issue on the control by uqmi for the WWAN module.
  But modemmanager can be used without any issues and the use of it is
  recommended.

- With the F2FS format, too many errors are reported on erasing eMMC
  partition "rootfs_data" while booting:

  [    1.360270] sdhci: Secure Digital Host Controller Interface driver
  [    1.363636] sdhci: Copyright(c) Pierre Ossman
  [    1.369730] sdhci-pltfm: SDHCI platform and OF driver helper
  [    1.374729] sdhci_msm 7824900.sdhci: Got CD GPIO
  ...
  [    1.413552] mmc0: SDHCI controller on 7824900.sdhci [7824900.sdhci] using ADMA 64-bit
  [    1.528325] mmc0: new HS200 MMC card at address 0001
  [    1.530627] mmcblk0: mmc0:0001 004GA0 3.69 GiB
  [    1.533530] mmcblk0boot0: mmc0:0001 004GA0 partition 1 2.00 MiB
  [    1.537831] mmcblk0boot1: mmc0:0001 004GA0 partition 2 2.00 MiB
  [    1.542918] mmcblk0rpmb: mmc0:0001 004GA0 partition 3 512 KiB, chardev (247:0)
  [    1.550323] Alternate GPT is invalid, using primary GPT.
  [    1.561669]  mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 p16 p17
  ...
  [    8.841400] mount_root: loading kmods from internal overlay
  [    8.860241] kmodloader: loading kernel modules from //etc/modules-boot.d/*
  [    8.863746] kmodloader: done loading kernel modules from //etc/modules-boot.d/*
  [    9.240465] block: attempting to load /etc/config/fstab
  [    9.246722] block: unable to load configuration (fstab: Entry not found)
  [    9.246863] block: no usable configuration
  [    9.254883] mount_root: overlay filesystem in /dev/mmcblk0p17 has not been formatted yet
  [    9.438915] urandom_read: 5 callbacks suppressed
  [    9.438924] random: mkfs.f2fs: uninitialized urandom read (16 bytes read)
  [   12.243332] mmc_erase: erase error -110, status 0x800
  [   12.246638] mmc0: cache flush error -110
  [   15.134585] mmc_erase: erase error -110, status 0x800
  [   15.135891] mmc_erase: group start error -110, status 0x0
  [   15.139850] mmc_erase: group start error -110, status 0x0
  ...(too many the same errors)...
  [   17.350811] mmc_erase: group start error -110, status 0x0
  [   17.356197] mmc_erase: group start error -110, status 0x0
  [   17.439498] sdhci_msm 7824900.sdhci: Card stuck in wrong state! card_busy_detect status: 0xe00
  [   17.446910] mmc0: tuning execution failed: -5
  [   17.447111] mmc0: cache flush error -110
  [   18.012440] F2FS-fs (mmcblk0p17): Found nat_bits in checkpoint
  [   18.062652] F2FS-fs (mmcblk0p17): Mounted with checkpoint version = 428fa16b
  [   18.198691] block: attempting to load /etc/config/fstab
  [   18.198972] block: unable to load configuration (fstab: Entry not found)
  [   18.203029] block: no usable configuration
  [   18.211371] mount_root: overlay filesystem has not been fully initialized yet
  [   18.214487] mount_root: switching to f2fs overlay

  So, this support uses ext4 format instead which has no errors.

Note:

- The primary uart is shared for debug console and Z-Wave chip. The
  function is switched by GPIO15 (Linux: 427).

  value:

    1: debug console
    0: Z-Wave

- NCP-HG100/Cellular has 2x os-image pairs in eMMC.

  - 0:HLOS, rootfs
  - 0:HLOS_1, rootfs_1

  In OpenWrt, the first image pair is used.

- "bootipq" command in U-Boot requires authentication with signed-image
  by default. To boot unsigned image of OpenWrt, use "mmc read" and
  "bootm" command instead.

- This support is for "Cellular" variant of NCP-HG100 and not tested on
  "WLAN" (non-cellular) variant.

- The board files of ipq-wifi may also be used in "WLAN" variant of
  NCP-HG100, but unconfirmed and add files as for "Cellular" variant.

- "NET" LED is used to indicate WWAN status in stock firmware.

- There is no MAC address information in the label on the case, use the
  address included in UUID in the label as "label-MAC" instead.

- The "CLOUD" LEDs are partially used for indication of system status in
  stock firmware, use they as status LEDs in OpenWrt instead of RGB LED
  connected to the MCU.

MAC addresses:

LAN    : 5C:FF:35:**:**:ED (ART, 0x6    (hex))
WAN    : 5C:FF:35:**:**:EF (ART, 0x0    (hex))
2.4 GHz: 5C:FF:35:**:**:ED (ART, 0x1006 (hex))
5 GHz  : 5C:FF:35:**:**:EE (ART, 0x5006 (hex))

partition layout in eMMC (by fdisk, GPT):

Disk /dev/mmcblk0: 7733248 sectors, 3776M
Logical sector size: 512
Disk identifier (GUID): ****
Partition table holds up to 20 entries
First usable sector is 34, last usable sector is 7634910

Number  Start (sector)    End (sector)  Size Name
     1              34            1057  512K 0:SBL1
     2            1058            2081  512K 0:BOOTCONFIG
     3            2082            3105  512K 0:QSEE
     4            3106            4129  512K 0:QSEE_1
     5            4130            4641  256K 0:CDT
     6            4642            5153  256K 0:CDT_1
     7            5154            6177  512K 0:BOOTCONFIG1
     8            6178            6689  256K 0:APPSBLENV
     9            6690            8737 1024K 0:APPSBL
    10            8738           10785 1024K 0:APPSBL_1
    11           10786           11297  256K 0:ART
    12           11298           11809  256K 0:HSEE
    13           11810           28193 8192K 0:HLOS
    14           28194           44577 8192K 0:HLOS_1
    15           44578          306721  128M rootfs
    16          306722          568865  128M rootfs_1
    17          568866         3958065 1654M rootfs_data

[initial work]
Signed-off-by: Iwao Yuki <dev.clef@gmail.com>
Co-developed-by: Iwao Yuki <dev.clef@gmail.com>
[adjustments, cleanups, commit message, sending patch]
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
(dropped clk_unused_ignore, dropped 901-* patches, renamed
key nodes, changed LEDs chan/labels to match func-en, made
:net -> (w)wan leds)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-09-24 23:53:53 +02:00
Tomasz Maciej Nowak
0410c95f0b ipq40xx: base-files: properly close case
Fix this occurrence during boot:
/bin/board_detect: line 10: Unsupported: not found

Fixes: 80baffd2aa (" ipq40xx: add support for Pakedge WR-1")
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
2022-09-24 23:53:53 +02:00
Kasparas Elzbutas
e562746263 ipq40xx: fix RUTX10 Wi-Fi woes
This partially reverts:
commit cfc13c4459 ("ipq40xx: utilize nvmem-cells for macs & (pre-)calibration data")

U-Boot on these devices mangles the device tree,
so nvmem-cell type calibration doesn't work.

Fixes: cfc13c4459 ("ipq40xx: utilize nvmem-cells for macs & (pre-)calibration data")
Signed-off-by: Kasparas Elzbutas <elzkas@gmail.com>
(added reference to commit, rewrote commit message)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-09-24 23:53:53 +02:00
David Bauer
4d014a7bd6 ipq40xx: add WAN LED mapping for GL-AP1300
Signed-off-by: David Bauer <mail@david-bauer.net>
2022-09-11 15:53:49 +02:00
Tomasz Maciej Nowak
80baffd2aa ipq40xx: add support for Pakedge WR-1
Pakedge WR-1 is a dual-band wireless router.

Specification
SoC: Qualcomm Atheros IPQ4018
RAM: 256 MB DDR3
Flash: 32 MB SPI NOR
WIFI: 2.4 GHz 2T2R integrated
      5 GHz 2T2R integrated
Ethernet: 5x 10/100/1000 Mbps QCA8075
USB: 1x 2.0
LEDS: 8x (3 GPIO controlled, 5 connected to switch)
Buttons: 1x GPIO controlled
UART: pin header J5
      1. 3.3V, 2. GND, 3. TX, 4. RX
      baud: 115200, parity: none, flow control: none

Installation
1. Rename initramfs image to:
   openwrt-ipq806x-qcom-ipq40xx-ap.dk01.1-c1-fit-uImage-initramfs.itb
   and copy it to USB flash drive with FAT32 file system.
2. Connect USB flash drive to the router and apply power while pressing
   reset button. Hold the button, on the lates bootloader version, when
   Power and WiFi-5 LEDs will start blinking release it. For the older
   bootloader holding it for 15 seconds should suffice.
3. Now the router boots the initramfs image, at some point (close to one
   minute) the Power LED will start blinking, when stops, router is fully
   booted.
4. Connect to one of LAN ports and use SSH to open the shell at
   192.168.1.1.
5. ATTENTION! now backup the mtd8 and mtd9 partitions, it's necessary if,
   at some point, You want to go back to original firmware. The firmware
   provided by manufacturer on its site is encrypted and U-Boot accepts
   only decrypted factory images, so there's no way to restore original
   firmware.
6. If the backup is prepared, transfer the sysupgrade image to the router
   and use 'sysupgrade' command to flash it.
7. After successful flashing router will reboot. At some point the Power
   LED will start blinking, wait till it stops, then router is ready for
   configuration.

Additional information
U-Boot command line is password protected. Password is unknown.

Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
2022-09-07 21:21:38 +02:00
David Bauer
e16a0e7e88 ipq40xx: add support for Extreme Networks WS-AP3915i
Hardware
--------
Qualcomm IPQ4029 WiSoC
2T2R 802.11 abgn
2T2R 802.11 nac
Macronix MX25L25635E SPI-NOR (32M)
512M DDR3 RAM
1x Gigabit LAN
1x Cisco RJ-45 Console port
Settings: 115200 8N1

Installation
------------

1. Attach to the Console port. Power up the device and press the s key
   to interrupt autoboot.

2. The default username / password to the bootloader is admin / new2day

3. Update the bootcommand to allow loading OpenWrt.

   $ setenv ramboot_openwrt "setenv serverip 192.168.1.66;
     setenv ipaddr 192.168.1.1; tftpboot 0x86000000 openwrt-3915.bin;
     bootm"
   $ setenv boot_openwrt "sf probe;
     sf read 0x88000000 0x280000 0xc00000; bootm 0x88000000"
   $ setenv bootcmd "run boot_openwrt"
   $ saveenv

4. Download the OpenWrt initramfs image. Serve it using a TFTP server as
   "openwrt-3915.bin" at 192.1681.66.

5. Download & boot the OpenWrt initramfs image on the access point.

   $ run ramboot_openwrt

6. Wait for OpenWrt to start.

7. Download and transfer the sysupgrade image to the device using e.g.
   SCP.

8. Install OpenWrt to the device using "sysupgrade"

   $ sysupgrade -n /path/to/openwrt.bin

Signed-off-by: David Bauer <mail@david-bauer.net>
2022-09-06 02:55:05 +02:00
Mark Mentovai
7f54bf6fe2
ipq40xx: add MikroTik wAP ac (RBwAPG-5HacD2HnD) support
The MikroTik wAP ac (RBwAPG-5HacD2HnD) is a dual-band dual-radio
802.11ac wireless access point with integrated antenna and two Ethernet
ports in a weatherproof enclosure. See
https://mikrotik.com/product/wap_ac for more information.

Important: this is the new ipq40xx-based wAP ac, not the older
ath79-based wAP ac (RBwAPG-5HacT2HnD), already supported in OpenWrt.

Specifications:
 - SoC: Qualcomm Atheros IPQ4018
 - CPU: 4x ARM Cortex A7
 - RAM: 128MB
 - Storage: 16MB NOR flash
 - Wireless
    - 2.4GHz: Built-in IPQ4018 (SoC) 802.11b/g/n 2x2:2, 2.5 dBi antennae
    - 5GHz: Built-in IPQ4018 (SoC) 802.11a/n/ac 2x2:2, 2.5 dBi antennae
 - Ethernet: Built-in IPQ4018 (SoC, QCA8075), 2x 1000/100/10Mb/s ports,
   one with 802.3af/at PoE in

Installation:
Boot the initramfs image via TFTP, then flash the sysupgrade image using
sysupgrade. Details at https://openwrt.org/toh/mikrotik/common.

Notes:
This preserves the MAC addresses of the physical Ethernet ports:
 - eth0 corresponds to the physical port labeled ETH1 and has the base
   MAC address. This port can be used to power the device.
 - eth1 corresponds to the physical port labeled ETH2 and has a MAC
   address one greater than the base.

MAC addresses are set from /lib/preinit/05_set_iface_mac_ipq40xx.sh
rather than /etc/board.d/02_network so that they are in effect for
preinit. This should likely be done for other MikroTik devices and
possibly other non-MikroTik devices as well.

As this device has 2 physical ports, they are each connected to their
respective PHYs, allowing the link status to be visible to software.
Since they are not marked on the case with any role (such as LAN or
WAN), both are bridged to the lan network by default, although this can
easily be changed if needed.

Signed-off-by: Mark Mentovai <mark@mentovai.com>
2022-07-18 01:45:47 +02:00
Matthew Hagan
811538ab22 ipq40xx: add support for Meraki MR74
The Meraki MR74 is part of the "Insect" series. This device is
essentially an outdoor variant of the MR33 with identical hardware, but
requiring a config@3 DTS option to be set to allow booting with the
stock u-boot.

The install procedure is replicated from the MR33, with the exception
being that the MR74 sysupgrade image must be used.

Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
2022-06-19 12:31:02 +02:00
Peter Adkins
b4184c666c ipq40xx: add support for Linksys WHW01 v1
This patch adds support for Linksys WHW01 v1 ("Velop") [FCC ID Q87-03331].

Specification
-------------

SOC:             Qualcomm IPQ4018
WiFi 1:          Qualcomm QCA4019 IEEE 802.11b/g/n
WiFi 2:          Qualcomm QCA4019 IEEE 802.11a/n/ac
Bluetooth:       Qualcomm CSR8811 (A12U)
Ethernet:        Qualcomm QCA8072 (2-port)
SPI Flash 1:     Mactronix MX25L1605D (2MB)
SPI Flash 2:     Winbond W25M02GV (256MB)
DRAM:            Nanya NT5CC128M16IP-DI (256MB)
LED Controller:  NXP PCA963x (I2C)
Buttons:         Single reset button (GPIO).

Notes
-----

There does not appear to be a way to trigger TFTP recovery without entering
U-Boot. The device must be opened to access the serial console in order to
first flash OpenWrt onto a device from factory.

The device has automatic recovery backed by a second set of partitions on
the larger of the two SPI flash ICs. Both the primary and secondary must
be flashed to prevent accidental rollback to "factory" after 3 failed boot
attempts.

Serial console
--------------

A serial console is available on the following pins of the populated J2
connector on the device mainboard (115200 8n1).

(<-- Top of PCB / Device)

  J2
  [o o o o o o]
       |   | |
       |   |  `-- GND
       |    `---- TX
       `--------- RX

Installation instructions
-------------------------

1. Setup TFTP server with server IP set to 192.168.1.236.
2. Copy compiled `...squashfs-factory.bin` to `nodes-jr.img` in tftp root.
3. Connect to console using pinout detailed in the serial console section.
4. Power on device and press enter when prompted to drop into U-Boot.
5. Flash first partition device via `run flashimg`.
6. Once complete, reset device and allow to power up completely.
7. Once comfortable with device upgrade reboot and drop back into U-Boot.
8. Flash the second partition (recovery) via `run flashimg2`.

Revert to "factory"
-------------------

1. Download latest firmware update from vendor support site.
2. Copy extracted `.img` file to `nodes-jr.img` in tftp root.
3. Connect to console using pinout detailed in the serial console section.
4. Power on device and press enter when prompted to drop into U-Boot.
5. Flash first partition device via `run flashimg`.
6. Once complete, reset device and allow to power up completely.
7. Once comfortable with device upgrade reboot and drop back into U-Boot.
8. Flash the second partition (recovery) via `run flashimg2`.

Link: https://github.com/openwrt/openwrt/pull/3682
Signed-off-by: Peter Adkins <peter@sunkenlab.com>
(calibration from nvmem, updated to 5.10+5.15)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-06-05 21:19:32 +02:00
Robert Marko
4d4462cc2a ipq40xx: mikrotik: provide BDF-s on demand
Since we now can pass the API 1 BDF-s aka board.bin to the ath10k
driver per radio lets use that to provide the BDF-s for MikroTik devices.

This also resolves the performance issues that happen as MikroTik changes
the boards and ships them under the same revision but they actually ship
with and require a different BDF.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2022-05-19 11:07:02 +02:00
Pawel Dembicki
af425e4221 ipq40xx: revert Cell-C RTL30VW to legacy caldata extraction
This partially reverts
commit cfc13c4459 ("ipq40xx: utilize nvmem-cells for macs & (pre-)calibration data").

After switching to nvmem RTL30VW, wifi was broken:

[   19.118319] ath10k_ahb a000000.wifi: qca4019 hw1.0 target 0x01000000 chip_id 0x003b00ff sub 0000:0000
[   19.118377] ath10k_ahb a000000.wifi: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
[   19.130285] ath10k_ahb a000000.wifi: firmware ver 10.4b-ct-4019-fW-13-5ae337bb1 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 6b2b5c5b
[   19.159092] ath10k_ahb a000000.wifi: failed to fetch board data for bus=ahb,vendor=0000,device=0000,subsystem-vendor=0000,subsystem-device=0000,variant=cellc,rtl30vw from ath10k/QCA4019/hw1.0/board-2.bin
[   19.238764] ath10k_ahb a000000.wifi: failed to fetch board-2.bin or board.bin from ath10k/QCA4019/hw1.0
[   19.238847] ath10k_ahb a000000.wifi: failed to fetch board file: -12
[   19.247362] ath10k_ahb a000000.wifi: could not probe fw (-12)
[   20.190797] ath10k_ahb a800000.wifi: qca4019 hw1.0 target 0x01000000 chip_id 0x003b00ff sub 0000:0000
[   20.190853] ath10k_ahb a800000.wifi: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
[   20.202893] ath10k_ahb a800000.wifi: firmware ver 10.4b-ct-4019-fW-13-5ae337bb1 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 6b2b5c5b
[   20.231357] ath10k_ahb a800000.wifi: failed to fetch board data for bus=ahb,vendor=0000,device=0000,subsystem-vendor=0000,subsystem-device=0000,variant=cellc,rtl30vw from ath10k/QCA4019/hw1.0/board-2.bin
[   20.317318] ath10k_ahb a800000.wifi: failed to fetch board-2.bin or board.bin from ath10k/QCA4019/hw1.0
[   20.317399] ath10k_ahb a800000.wifi: failed to fetch board file: -12
[   20.326098] ath10k_ahb a800000.wifi: could not probe fw (-12)

Bootloader mangles in NAND partitions and removes precal@X nodes in
working system:

root@OpenWrt:~# echo $(cat /sys/firmware/devicetree/base/soc/spi@78b5000/flash@0/partitions/partition@170000/label)
0:ART
root@OpenWrt:~# ls /sys/firmware/devicetree/base/soc/spi@78b5000/flash@0/partitions/partition@170000/
label  name   reg

Revert to legacy method fixed the problem.

Fixes: cfc13c4459 ("ipq40xx: utilize nvmem-cells for macs & (pre-)calibration data")
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2022-05-15 16:32:25 +02:00
Christian Lamparter
834c9b3f05 ipq40xx: Lyra: update RGB LED-Controller node for 5.10+
Add the reg and color property to each channel node. This
update is to accommodate the multicolor framework.

Refer to:
<https://lore.kernel.org/all/20200622185919.2131-9-dmurphy@ti.com>
<https://lore.kernel.org/all/20210818070209.1540451-1-michal.vokac@ysoft.com>

Note:

There is only a single extremely bright RGB-LED.
The RGB-color channels (i.e.: blue-0, blue-1 and blue-2)
are running in parallel to increase the current delivery
beyond what a single PWM-output on the LED controller
could do.

BugLink: https://github.com/openwrt/openwrt/issues/9851
Reported-By: Thomas Bøge <thomas@boegenielsen.dk>
Tested-By: Thomas Bøge <thomas@boegenielsen.dk>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-05-14 11:08:45 +02:00
Christian Lamparter
026fda10a5 ipq40xx: WAC510: device-tree overhauling
removes usb-port remains as neither the WAC510 nor the WAC505
come with a USB port. Update the LED properties to phase out
labels and introduce generic node-names as well as adding
the color, function and function-enumerator properties.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-03-26 02:02:44 +01:00
Brian Norris
f1c041e34f ipq40xx: Add subtarget for Google WiFi (Gale)
Google WiFi (codename: Gale) is an IPQ4019-based AP, with 2 Ethernet
ports, 2x2 2.4+5GHz WiFi, 512 MB RAM, 4 GB eMMC, and a USB type C port.
In its stock configuration, it runs a Chromium OS-based system, but you
wouldn't know it, since you can only manage it via a "cloud" +
mobile-app system.

The "v2" label is coded into the bootloader, which prefers the
"google,gale-v2" compatible string. I believe "v1" must have been
pre-release hardware.

Note: this is *not* the Google Nest WiFi, released in 2019.

I include "factory.bin" support, where we generate a GPT-based disk
image with 2 partitions -- a kernel partition (using the custom "Chrome
OS kernel" GUID type) and a root filesystem partition. See below for
flashing instructions.

Sysupgrade is supported via recent emmc_do_upgrade() helper.

This is a subtarget because it enables different features
(FEATURES=boot-part rootfs-part) whose configurations don't make sense
in the "generic" target, and because it builds in a few USB drivers,
which are necessary for installation (installation is performed by
booting from USB storage, and so these drivers cannot be built as
modules, since we need to load modules from USB storage).

Flashing instructions
=====================

Documented here:
https://openwrt.org/inbox/toh/google/google_wifi

Note this requires booting from USB storage.

Features
========

I've tested:

 * Ethernet, both WAN and LAN ports
 * eMMC
 * USB-C (hub, power-delivery, peripherals)
 * LED0 (R/G/B)
 * WiFi (limited testing)
 * SPI flash
 * Serial console: once in developer mode, console can be accessed via
   the USB-C port with SuzyQable, or other similar "Closed Case
   Debugging" tools:
     https://chromium.googlesource.com/chromiumos/third_party/hdctools/+/master/docs/ccd.md#suzyq-suzyqable
 * Sysupgrade

Not tested:

 * TPM

Known not working:

 * Reboot: this requires some additional TrustZone / SCM
   configuration to disable Qualcomm's SDI. I have a proposal upstream,
   and based on IRC chats, this might be acceptable with additional DT
   logic:
     [RFC PATCH] firmware: qcom_scm: disable SDI at boot
     https://lore.kernel.org/linux-arm-msm/20200721080054.2803881-1-computersforpeace@gmail.com/
 * SMP: enabling secondary CPUs doesn't currently work using the stock
   bootloader, as the qcom_scm driver assumes newer features than this
   TrustZone firmware has. I posted notes here:
     [RFC] qcom_scm: IPQ4019 firmware does not support atomic API?
     https://lore.kernel.org/linux-arm-msm/20200913201608.GA3162100@bDebian/
 * There's a single external button, and a few useful internal GPIO
   switches. I haven't hooked them up.

The first two are fixed with subsequent commits.

Additional notes
================

Much of the DTS is pulled from the Chrome OS kernel 3.18 branch, which
the manufacturer image uses.

Note: the manufacturer bootloader knows how to patch in calibration data
via the wifi{0,1} aliases in the DTB, so while these properties aren't
present in the DTS, they are available at runtime:

  # ls -l
/sys/firmware/devicetree/base/soc/wifi@a*/qcom,ath10k-pre-calibration-data
  -r--r--r--    1 root     root         12064 Jul 15 19:11 /sys/firmware/devicetree/base/soc/wifi@a000000/qcom,ath10k-pre-calibration-data
  -r--r--r--    1 root     root         12064 Jul 15 19:11 /sys/firmware/devicetree/base/soc/wifi@a800000/qcom,ath10k-pre-calibration-data

Ethernet MAC addresses are similarly patched in via the ethernet{0,1} aliases.

Signed-off-by: Brian Norris <computersforpeace@gmail.com>
(updated 901 - x1pro moved in the process)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-03-25 18:14:13 +01:00
Nicholas Smith
7ea2f3d6e2 ipq40xx: add support for Telco X1 Pro
Telco X1 Pro is a Cat12 LTE-A Pro modem router.
Vendor firmware is based on a recent version of OpenWrt.
Flashing is possible via CLI using sysupgrade -F -n
The serial headers allow bootloader and console access
Serial setting: 115200  8N1

Brief Specifications:
IPQ4019 SoC
32MB flash
512MB RAM
4x gigabit LAN
1x gigabit WAN
Dual-band Wave-2 wifi
2x SMA LTE antenna connectors
2x RP-SMA wifi antennas
1x USB 2.0 port
1x Reset button
Serial headers installed
1x Nano SIM tray
1x Quectel EM-12G LTE-A Pro modem
1x M.2 slot attached to USB 3.0
1x internal micro SD card slot

Signed-off-by: Nicholas Smith <nicholas@nbembedded.com>
2022-03-19 20:05:00 +01:00