This patch adds supports for GL-X1200.
Specification:
- SOC: QCA9563 (775MHz)
- Flash: 16 MiB
- RAM: 128 MiB DDR2
- Ethernet: 4x 1Gbps LAN + 1x 1Gbps WAN
- Wireless: QCA9563(2.4GHz) and QCA9886(5GHz)
- SIM: 2x SIM card slots
- MicroSD: 1x microSD slot
- Antenna: 2x external 5dBi antennas
- USB: 1x USB 2.0 port
- Button: 1x reset button
- LED: 16x LEDs (3x GPIO controllable)
- UART: 1x UART on PCB (JP1: 3.3V, RX, TX, GND)
- OEM U-Boot supplies HTTP/GUI access
Implementation Notes
====================
Both the NOR and NAND variants boot off a NOR-based kernel,
consistent with the OEM's firmware.
The mode LEDs are
* Boot, Running system
* Failsafe 2G
* Upgrade 5G
Installation
============
Using sysupgrade
----------------
sysupgrade may be used to install a NAND image on a device running
a NAND image or a NOR image on a device running a NOR image. It is
recommended to *not* preserve config when upgrading from OEM firmware
or previous versions of OpenWrt. No supported sysupgrade path should
require "force". Transitioning from NOR to NAND can be accomplished
Using U-Boot
------------
The OEM U-Boot can be put into a graphical, firmware-upload mode by
holding down the button on the side of the router while applying power
and for a bit more than five seconds following with the current OEM
U-Boot. The power LED will come on, then the 5G LED will flash five
times, about once a second. When the 5G LED stops flashing and the
2G LED lights solid, the router's U-Boot will provide an upload page
at http://192.168.1.1/ Either a browser may be used to upload an image,
or a utility such as curl may be used:
curl -X POST -F gl_firmware=\@*-nand-squashfs-factory.img \
http://192.168.1.1/index.html
or
curl -X POST -F gl_firmware=\@*-nor-squashfs-sysupgrade.bin \
http://192.168.1.1/index.html
Note that NOR vs. NAND is based on the file name extension.
Signed-off-by: Xinfa Deng <xinfa.deng@gl-inet.com>
The utils subtarget was used for uClibc and eglibc
which are both obsolete and replaced in Openwrt by mainline
musl and glibc, which do not have a utils Makefile target.
Ref: 5d19a38d8 ("toolchain: sync eglibc headers/build split with uclibc changes")
Fixes: 63fb17520 ("toolchain: remove uClibc-ng")
Suggested-by: Andre Heider <a.heider@gmail.com>
Signed-off-by: Michael Pratt <mcpratt@pm.me>
Reorganize dependencies between toolchain targets to save a line.
This also puts them in a linear order which is easier to read.
Signed-off-by: Michael Pratt <mcpratt@pm.me>
Use the gcc/final/install target stampfile as the prerequisite
for the toolchain/compile target stampfile.
The previous filename was also incorrect,
the stampfile name format was changed (see reference)
but was never updated here.
The issue was never noticed
because the usage of timestamp.pl was broken
(fixed in previous commit)
causing the extra prereq files passed to 'call stampfile'
to never get checked at all.
Fixes: 5149ed151 ("gcc: split up the build process into three distinct stages")
Signed-off-by: Michael Pratt <mcpratt@pm.me>
Release notes:
- Feature: link down event statistics (no option)
- Feature: JSON output for coalesce (-c)
- Feature: new link modes (no option)
- Feature: JSON output for ring (-g)
- Feature: netlink handler for RSS get (-x)
- Fix: fix boolean value output in JSON output
- Fix: fix build errors and warnings
Remove upstreamed patches:
- 100-uapi-Bring-in-if-h.patch
- 101-netlink-Fix-maybe-uninitialized-meters-variable.patch
- 102-raw-marvell-c-Fix-build-with-musl-libc.patch
Signed-off-by: Nick Hainke <vincent@systemli.org>
In DHCPv6-PD enabled environments, addresses are assigned to interfaces.
These new functions retrieve the IPv6 assigned prefix(es).
Signed-off-by: Mark Baker <mark@vpost.net>
The CONFIG_PPC_QUEUED_SPINLOCKS configuration option is not defined for
kernel 5.15, it is defined for kernel 5.10.
This fixes the compilation of mpc85xx/p2020 with kernel 5.15.
Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Synchronize the ath11k backports with the current ath-next tree.
This backports several memory leak issues, PCI IRQ fixup, peer add locking
fix as well as IPQ5018 support, though IPQ5018 support is unused for now.
This allows to easily backport further fixes as cherry picking them has
started requiring manual conflict resolution.
Signed-off-by: Robert Marko <robimarko@gmail.com>
They were backported to stable kernels but we backport more stuff on our
own so we have to pick up few remaining.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
The default kernel should be switched to 5.15 in order to enable testing
by a broader audience.
Tested on TP-Link TL-WDR4900 v1.
Acked-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
Signed-off-by: Nick Hainke <vincent@systemli.org>
PowerPC CONFIG_ARCH is defined as powerpc, not ppc. Fix that in the
DEPENDS condition.
Arc needs to be built with libatomic. Change the OpenSSL configuration
file, and add it to the libatomic DEPENDS condition.
Fixes: 7e7e76afca "openssl: bump to 3.0.8"
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Armada 7040 uses a rather small 15MB memory window for every PCI adapter,
however this is not sufficient for Qualcomm QCA6390 802.11ax cards that
are shipped along with the OpenWrt WLAN model of MOCHAbin as ath11k
requires at least 16MB of memory.
So, similar to what MACCHIATOBin has been doing for years, lets move
to using the second PCIe 2 memory window and expand it to 128MB to
make it future proof.
This has been already sent upstream [1].
[1] https://lore.kernel.org/linux-arm-kernel/20230219121418.1395401-1-robert.marko@sartura.hr/
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
This patch introduces DSA support for TP-Link TL-WDR4900 v1 switch.
Swconfig driver for QCA8327 switch is removed because this router is
only one device which use Qualcom swconfig switch.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Tested-by: Nick Hainke <vincent@systemli.org> # TP Link WDR4900 v1 (5.15)
The -Xpreset option changed format and dropped the -Xe and just require
the extreme string to be passed to the -Xpreset option.
Update the LZMA_XZ_OPTIONS to reflect this change.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
squashfs tool is finally reborn and correctly maintained.
Introduce the new version as a replacement for squasfs4kit as it was a
fork and also abandoned.
Add additional patch to add the missing feature present in squashfskit4
but still missing on this new project.
Backport each required patch that fix compilation error on macos.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This was apparently introduced to recreate the toolchain (wipe
staging_dir/toolchain*, but keep build_dir/toolchain*, followed by a
`make toolchain/compile`).
But it leaves leftovers and causes re-links to happen at src_install phase,
because of the changed paths, possibly adding yet another source of issues.
With the prior commits removing various hacks related to the "initial"
folder we can remove installing it twice altogether.
The recreated toolchain is exactly the same as before.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Add it to the existing list to fix it up.
Found by mold:
toolchain-x86_64_gcc-12.2.0_glibc/lib/libm.so:4: GROUP ( /lib/libm.so.6 AS_NEEDED ( /lib/libmvec.so.1 ) )
^ library not found: /lib/libm.so.6
Signed-off-by: Andre Heider <a.heider@gmail.com>
A modern glibc only links against libgcc_eh for its tests or when building it
static, which doesn't happen here.
Reverts a hunk of: a3edea1b "add support for alternative C libraries..."
Signed-off-by: Andre Heider <a.heider@gmail.com>
This reverts commit 9d1b619cb1.
No Linaro binutils are supported anymore, the leftover removal commit
missed one line.
Fixes: b648e1c0 "binutils: remove 2.25.1 support and leftovers of older versions"
Signed-off-by: Andre Heider <a.heider@gmail.com>
In [0] support for ARC specific binutils were added, which was later removed
again [Fixes:].
Upstream binutils never had an extlib.
[0] 8b5d644b "toolchain: add support of ARC architecture"
Fixes: 8568dcd9 "toolchain: Remove binutils 2.29 for ARC targets"
Signed-off-by: Andre Heider <a.heider@gmail.com>
This patch fixes a corner case when using passwords that are exactly 64
characters in length with mesh mode or passwords longer than 63 characters
with SAE because 'psk' is used instead of 'sae_password'.
SAE is obligatory for 802.11s (mesh point).
The 'psk' option for hostapd is suited for WPA2 and enforces length
restrictions on passwords. Values of 64 characters are treated as PMKs.
With SAE, PMKs are always generated during the handshake and there are no
length restrictions.
The 'sae_password' option is more suited for SAE and should be used
instead.
Before this patch, the 'sae_password' option is only used with mesh mode
passwords that are not 64 characters long.
As a consequence:
- mesh passwords can't be 64 characters in length
- SAE only works with passwords with lengths >8 and <=63 (due to psk
limitation).
Fix this by always using 'sae_password' with SAE/mesh and applying the PMK
differentiation only when PSK is used.
Fixes: #11324
Signed-off-by: Leon M. Busch-George <leon@georgemail.eu>
[ improve commit description ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Wiflyer WF3526-P and Zbtlink ZBT-WE1326 have the same circuit design.
Installing the misunderstading firmware of ZBT-WE3526 will cause Wi-Fi
not work due to allocate the wrong pcie port. Add alternative name to
help users easily build or download the correct firmware.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
MT7621 gets a new PCIe driver in the 5.15+ kernel. Allocating wrong PCIe
port will cause the PCIe NIC to not work properly. This commit fixes
the wrong port numbers on Zbtlink ZBT-WE1326.
According to the bootlog, MT7612E (5 GHz) is connected to pcie1, and
MT7603E (2 GHz) is connected to pcie2:
[4.197658] mt7621-pci 1e140000.pcie: pcie0 no card, disable it (RST & CLK)
[4.204609] mt7621-pci 1e140000.pcie: PCIE1 enabled
[4.209476] mt7621-pci 1e140000.pcie: PCIE2 enabled
...
[4.307988] pci 0000:01:00.0: [14c3:7662] type 00 class 0x028000
[4.367206] pci 0000:02:00.0: [14c3:7603] type 00 class 0x028000
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
On some devices the chip has RTC but no battery save time.
This leads back to getting the wrong time
and skipping the check of the last file modification date.
This commit ensures that the file time is checked even
if the RTC exists.
which would ordinarily return an approbiate
system time used for e.g. certificate generation.
Tested-on: NanoPi R2S
Signed-off-by: Yuan Tao <ty@wevs.org>
The name of squashfs is confusing since in reality it's a really old
version using an old lzma library. This tools is used for old ath79
netgear target and to produde a fake squasfs3 image needed for some
specific bootloader from some OEM (AVM for example)
Rename squashfs tool to squasfs3-lzma to better describe it.
Rename the installed bin from mksquashfs-lzma to mksquashfs3-lzma.
Use tar transform to migrate the root directory in tar to the new
naming.
Drop redundant PKG_CAT variable not needed anymore.
Also update any user of this tool.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Including kernel.mk moves the package build folder in the linux one, which
is confusing since this isn't building any kernel modules.
package-defaults.mk is already included my package.mk.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Chromium devices (like Google WiFi) have ramoops memory reserved by the
bootloader. Let's enable the ramoops kernel module by default, so we get
better crash logging.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Chromium devices (like OnHub) have ramoops memory reserved by the
bootloader. Let's enable the ramoops kernel module by default, so we get
better crash logging.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Pstore ramoops support is useful even when there isn't an explicit
panic/crash. We can log all kernel messages via a "console", and then
retrieve them in the event of some non-kernel-panic reset (e.g.,
watchdog).
Since the buffer memory is already reserved, there isn't much overhead
to doing this.
The new console files will show up as:
/sys/fs/pstore/console-ramoops-N
Cc: Hannu Nyman <hannu.nyman@iki.fi>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
